MasterFormat: 95

SpecWizard: customize this spec    Download this Solid Surfaces Specification for   WORD | WP | RTF | TEXT

Find over 500 more construction specifications | Arcat.com

	SECTION 06600
	SOLID SURFACES
	Copyright 2008 - 2013 ARCAT, Inc. - All rights reserved
	** NOTE TO SPECIFIER ** InPro Corporation (IPC); Solid Surfaces. This section is based on solid surface material manufactured by InPro Corporation, which is located at: P.O. Box 406 S 80 W 18766 Apollo Drive Muskego, WI 53150 Toll Free Tel: 800 222-5556 Tel: 262-679-9010 Fax: 262-679-5531 E-mail: jjohnson@inprocorp.com. Website: www.inprocorp.com . InPro Corporation manufactures a wide range of interior protection products and decorative surfaces. . InPro Corporation is now considered by many to be the worldwide leader in its industry, since it is the only company in the industry to manufacture all the rigid and flexible plastic products it sells. .
	PART 1	GENERAL
	1.1	SECTION INCLUDES
	** NOTE TO SPECIFIER ** Retain only items below required for project. Add additional custom surfaces not listed.
		A.	Solid surfacing fabrications for the following applications:
			1.	Vanity tops.
			2.	Shower and tub surrounds.
			3.	Countertops and sinks.
			4.	Wall panels / sheet stock.
			5.	Window sills.
			6.	Custom fabrications including:
				a.	Tub and shower walls.
				b.	Wall cladding/wainscoting.
				c.	Bumper rails.
				d.	Laboratory countertops.
				e.	Reception areas/nurses' stations.
				f.	Tabletops.
				g.	Bar tops.
				h.	Cold cafeteria surfaces.
				i.	Hot cafeteria surfaces.
				j.	Cove backsplashes.
				k.	Colored inlays.
				l.	Shower receptor/bases.
				m.	Decorative panels.
	1.2	RELATED SECTIONS
	** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
		A.	Section 06100 - Rough Carpentry: Framing and blocking.
		B.	Section 09260 - Gypsum Board Assemblies.
		C.	Section 15100 - Building Services Piping.
		D.	Section 15410 - Plumbing Fixtures: Adjacent plumbing fixture installation.
	1.3	REFERENCES
	** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
		A.	ANSI Z 124.1.2 - Plastic Bathtub and Shower Units.
		B.	ANSI Z 124.3 - Plastic Lavatories.
		C.	ANSI Z 124.6 - Plastic Sinks, section 5.5 Chemical Resistance.
		D.	ASTM E 84 - Standard Test Method for Surface Burning Characteristics of Building Materials.
		E.	ASTM F 462 - Standard Consumer Safety Specification for Slip-Resistant Bathing Facilities.
		F.	ASTM G 21 - Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi.
		G.	ASTM G 22 - Standard Practice for Determining Resistance of Plastics to Bacteria.
		H.	NFPA 255 - Standard Method of Test of Surface Burning Characteristics of Building Materials.
		I.	UL 723 - Test for Surface Burning Characteristics of Building Materials.
	1.4	PERFORMANCE REQUIREMENTS:
		A.	Provide solid surface material that conforms to ANSI/ICPA SS-1 for workmanship and finish, structural integrity and material characteristics.
	** NOTE TO SPECIFIER ** Retain only paragraphs applicable to the surfaces specified in this section, and delete all others.
		B.	Provide Lavatory tops and sinks that conform to ANSI Z 124.3-2005 when tested in the following areas:
			1.	Color fastness - No change, 200 hours.
			2.	Wear and Cleaning - Passes.
			3.	Impact resistance - Passes.
			4.	Stain Resistance - Passes.
			5.	Chemical Resistance - Passes.
			6.	Drain Fitting Connection - Passes.
			7.	Loads on Lavatory Tops - Passes.
			8.	Thermal Shock Resistance - Passes.
			9.	Cigarette Burn Test - Passes.
		C.	Provide shower receptors and shower systems that conform to ANSI Z 124.1.2-2005 when tested for workmanship and finish, structural integrity and material characteristics.
		D.	Provide sinks that conform to ANSI Z 124.6-2005 when tested for workmanship and finish, structural integrity and material characteristics.
	** NOTE TO SPECIFIER ** The next three paragraphs apply only to PRISM material. Delete if not required.
		E.	Fungal and Bacterial Resistance: Provide a solid surface that does not support fungal and bacterial growth as tested in accordance with ASTM G 21 and ASTM G 22.
		F.	Provide solid surface material that conforms to ANSI/ICPA SS-1 for workmanship and finish, structural integrity and material characteristics.
		G.	Fire Performance Characteristics: Provide a solid surface wall cladding conforming with the NFPA class A fire rating as determined by ASTM E 84, UL 723, NFPA 255.
	1.5	SUBMITTALS
		A.	Submit under provisions of Section 01300.
		B.	Product Data: Manufacturer's complete and current product data for each product required, including:
			1.	Preparation instructions and recommendations.
			2.	Storage and handling requirements and recommendations.
			3.	Complete installation methods.
		C.	Shop Drawings: Show locations of each item and installation details. Provide plan, section and elevation drawings conditions as necessary to depict correct installation procedures.
		D.	Selection Samples: Color charts consisting of actual product pieces, demonstrating full range of available colors, for initial color selection.
		E.	Verification Samples: 3 inch (76 mm) square samples.
	1.6	QUALITY ASSURANCE
		A.	Manufacturer Qualifications: All primary products specified in this section will be provided by a single manufacturer with a minimum of ten (10) years experience.
		B.	Installer Qualifications: All products listed in this section are to be installed by a single installer with a minimum of five (5) years demonstrated experience in installing products of the same type and scope as specified.
	** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.
		C.	Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.
			1.	Finish areas designated by Architect.
			2.	Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.
			3.	Refinish mock-up area as required to produce acceptable work.
		D.	Provide test reports showing compliance with the performance specified for:
			1.	Fire-related properties.
			2.	Accessibility and safety properties.
			3.	Impact strength.
			4.	Coefficient of friction.
	1.7	DELIVERY, STORAGE, AND HANDLING
		A.	Store products in manufacturer's unopened packaging until ready for installation.
		B.	Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.
	1.8	PROJECT CONDITIONS
		A.	Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.
	1.9	WARRANTY
		A.	At project closeout, provide to the owner or owners representative an executed copy of the manufacturer's limited warranty against manufacturing defect outlining its terms, conditions and exclusions from coverage.
			1.	Duration: Ten (10) years.
	PART 2	PRODUCTS
	2.1	MANUFACTURERS
		A.	Acceptable Manufacturer: InPro Corporation, which is located at: S80 W18766 Apollo Dr. ; Muskego, WI 53150; Toll Free Tel: 800-222-5556; Tel: 262-679-9010; Fax: 262-679-9127; Email: request info; Web: www.inprocorp.com
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
		B.	Substitutions: Not permitted.
		C.	Requests for substitutions will be considered in accordance with provisions of Section 01600.
	** NOTE TO SPECIFIER ** Delete this entire article if Vanity Tops are not required. Where more than one type is required, coordinate locations with Contract Drawings and / or add statements describing locations for each style.
	2.2	VANITY TOPS
		A.	PRISM Solid Surface Lavatory Tops:
			1.	Maximum size 36 inches x 144 inches (914mm x 3658mm), Shape - As shown in Contract Drawings.
	** NOTE TO SPECIFIER ** Select Lavatory Top Thickness. Delete two of the next three paragraphs.
			2.	Thickness: 1 inch (25 mm).
			3.	Thickness: 1 1/4 inches (32 mm).
			4.	Thickness: 1 1/2 inches (38 mm)., or other indicated by specifier.
	** NOTE TO SPECIFIER ** Select Edge Type. Delete one of the next two paragraphs.
			5.	Edge Type: Standard Edge, with bottom perimeter pad of MDF.
			6.	Edge Type: Upgrade Edge, with edge inlay option.
	** NOTE TO SPECIFIER ** Delete six of the next seven paragraphs.
			7.	Edge Treatment: Double Eased - 1/8 inch (3 mm) Radius.
			8.	Edge Treatment: Double Radius - 1/4 inch (6 mm) Radius.
			9.	Edge Treatment: Bevel - 1/4 inch (6 mm) Bevel.
			10.	Edge Treatment: Double Bevel - 1/4 inch (6 mm) Bevel.
			11.	Edge Treatment: S-Curve.
			12.	Edge Treatment: Classic Ogee.
			13.	Edge Treatment: Full Bullnose.
	** NOTE TO SPECIFIER ** Select Backsplash Type. Delete one of the next two paragraphs.
			14.	Backsplash: Attached coved backsplash with detached sidesplash.
			15.	Backsplash: Detached straight backsplash and sidesplash.
	** NOTE TO SPECIFIER ** Select Front Apron Type. Delete three of the next four paragraphs.
			16.	Front Apron: Flush.
			17.	Front Apron: Reveal, 3/8 inch x 1/8 inch (10 mm x 3 mm).
			18.	Front Apron: Setback.
			19.	Front Apron: Detached setback.
	** NOTE TO SPECIFIER ** Select Lavatory and Sink mounting method. Delete four of the next five paragraphs.
			20.	Sink Mounting: Integrally bonded - Roundover perimeter.
			21.	Sink Mounting: Integrally bonded - Bevel perimeter.
			22.	Sink Mounting: Integrally bonded - S-curve perimeter.
			23.	Sink Mounting: Mechanically Fastened and Sealed - Bullnose.
			24.	Sink Mounting: Mechanically Fastened and Sealed - Double 1/4 inch radius.
	** NOTE TO SPECIFIER ** Select Sink Type. Delete three of the next four paragraphs.
			25.	Sink: QS Standard Lav - inside dimensions: 17-1/4 inches w x 13-3/4 inches high x 5-3/4 inches deep (438 mm x 349 mm high x 146 mm deep).
			26.	Sink: QS ADA Lav - inside dimensions: 15-7/8 inches w x 12-3/4 inches high x 4 inches deep (403 mm x 324 mm high x 102 mm deep).
			27.	Sink: QS Small Lav - inside dimensions: 16-1/4 inches w x 10-1/2 inches high x 6 inches deep (413 mm x 267 mm high x 152 mm deep).
			28.	Sink: QS Enclosed Overflow (E/O).
				a.	Inside Dimensions: 17 inches w x 14 inches high x 6 inches deep (431 mm x 355 mm high x 152 mm deep).
	** NOTE TO SPECIFIER ** Delete this entire article if Shower And Tub Surrounds are not required. Where more than one type is required, coordinate locations with Contract Drawings and / or add statements describing locations for each style.
	2.3	SHOWER AND TUB SURROUNDS
		A.	Shower Surrounds:
			1.	32 inch x 32 inch Square Shower:
				a.	Door and shower receptor are not included.
				b.	Panels: back, right, and left wall panels.
			2.	36 inch x 36 inch Square Shower:
				a.	Door and shower receptor are not included.
				b.	Panels: back, right, and left wall panels.
			3.	32 inch x 48 inch One-Piece Back Wall Rectangular Shower.
				a.	Door and shower receptor are not included.
				b.	Panels: back, right, and left wall panels.
			4.	36 inch x 48 inch One-Piece Back Wall Rectangular Shower:
				a.	Door and shower receptor are not included.
				b.	Panels: back, right, and left wall panels.
			5.	36 inch x 60 inch One-Piece Back Wall Rectangular Shower:
				a.	Door and shower receptor are not included.
				b.	Panels: back, right, and left wall panels.
			6.	42 inch x 48 inch One-Piece Back Wall Rectangular Shower:
				a.	Door and shower receptor are not included.
				b.	Panels: back, right, and left wall panels.
			7.	32 inch x 60 inch Two-Piece Back Wall Rectangular Shower:
				a.	Door and shower receptor are not included.
				b.	Panels: back, right, and left wall panels.
			8.	36 inch x 60 inch Two-Piece Back Wall Rectangular Shower:
				a.	Door and shower receptor are not included.
				b.	Panels: back, right, and left wall panels.
			9.	36 inch Double Threshold Shower:
				a.	Door and shower receptor are not included.
				b.	Panels: back wall panels.
			10.	36 inch x 36 inch Neo-angle Shower:
				a.	Doors and shower receptor are not included.
				b.	Panels: back wall panels.
			11.	42 inch x 42 inch Neo-angle Shower:
				a.	Doors and shower receptor are not included.
				b.	Panels: back wall panels.
	** NOTE TO SPECIFIER ** Select Wall Height. Delete one of the next two paragraphs.
			12.	Wall Height: 72 inches (1829 mm).
			13.	Wall Height: 96 inches (2438 mm).
	** NOTE TO SPECIFIER ** Delete patterns not required.
			14.	Pattern: 4 inch (102 mm) squares.
			15.	Pattern: Diamond Accent Listello.
			16.	Pattern: 8 inch (203 mm) squares.
			17.	Pattern: Diamond.
			18.	Pattern: 6 inches (152 mm) x 24 inches (610 mm) horizontal.
			19.	Pattern: Beadboard.
			20.	Pattern: 3 inches (76 mm) x 6 inches (152 mm) Subway.
			21.	Pattern: Plankboard.
			22.	Pattern: 12 inch (305 mm) squares.
			23.	Pattern: Diamond Accent.
			24.	Pattern: Eclipse.
			25.	Pattern: Matrix.
			26.	Pattern: Tudor.
			27.	Pattern: Smooth Panel.
	** NOTE TO SPECIFIER ** Retain only Shower and Tub surround accessories required on this project. Delete the entire paragraph if accessories are not required.
		B.	Shower and Tub Surround Accessories:
	** NOTE TO SPECIFIER ** Soap Caddies, Soap Dishes and Shower Seats only Available with cultured products. Delete if not required.
			1.	Inside Corner Molding: Trapezoid-shaped corner molding, 3/4 inch (19 mm) from corner x 15/16 inch (25 mm) thick x 96 inch (2438 mm) h.
			2.	Batten Strip: Rectangular strip with radiused edges, 2-1/2 inch x 1/4 inch x 96 inch h (64 mm x 6 mm x 2438 mm).
	** NOTE TO SPECIFIER ** Delete styles not required for project or delete this entire article if Countertops and Sinks are not required. Where more than one type is required, coordinate locations with Contract Drawings and / or add statements describing locations for each style.
	2.4	COUNTERTOPS AND SINKS
		A.	PRISM Solid Surface Sinks:
			1.	Double Bowl:
				a.	Inside Dimensions: 29-1/4 inch w x 16-15/16 inch d x 9 inch h, (743 mm x 430 mm x 228 mm) Double Sink.
	** NOTE TO SPECIFIER ** Select Mounting Method. Delete one of the next two paragraphs.
				b.	Mounting: Undermount.
				c.	Mounting: Integral.
			2.	Offset Bowl:
				a.	Inside Dimensions: 30 inch w x 18 inch d x 8-1/2 inch h, (762 mm x 457 mm x 216 mm) Double Sink.
	** NOTE TO SPECIFIER ** Select Mounting Method. Delete one of the next two paragraphs.
				b.	Mounting: Undermount.
				c.	Mounting: Integral.
			3.	Large Rectangle:
				a.	Inside Dimensions: 20-7/8 inch w x 15-7/8 inch d x 7-1/2 inch h (530 mm x 403 mm x 190 mm), Single Sink.
			4.	Small Rectangle:
				a.	Inside Dimensions: 14 inch w x 10 inch d x 7-1/2 inch h (355 mm x 254 mm x 190 mm), Single Sink.
			5.	Square:
				a.	Inside Dimensions: 15-3/4 inch w x 15-3/4 inch d x 8-3/8 inch h (400 mm x 400 mm x 212 mm), Double Sink.
		B.	PRISM Solid Surface Counter Tops:
			1.	Maximum size 36 inches x 144 inches (914mm x 3658mm), Shape - As shown in Contract Drawings.
	** NOTE TO SPECIFIER ** Select Lavatory Top Thickness. Delete two of the next three paragraphs.
			2.	Thickness, 1 inch (25mm)
			3.	Thickness: 1 1/4 inches (32mm)
			4.	Thickness: 1 1/2 inches (38 mm), or other indicated by specifier.
	** NOTE TO SPECIFIER ** Select Edge Type. Delete one of the next two paragraphs.
			5.	Edge Type: Standard Edge, with bottom perimeter pad of MDF.
			6.	Edge Type: Upgrade Edge, with edge inlay option.
	** NOTE TO SPECIFIER ** Delete six of the next seven paragraphs.
			7.	Edge Treatment: Double Eased - 1/8 inch (3 mm) Radius.
			8.	Edge Treatment: Double Radius -1/4 inch (6 mm) Radius.
			9.	Edge Treatment: Bevel - 1/4 inch (6 mm) Bevel.
			10.	Edge Treatment: Double Bevel -1/4 inch (6 mm) Bevel.
			11.	Edge Treatment: S-Curve.
			12.	Edge Treatment: Classic Ogee.
			13.	Edge Treatment: Full Bullnose.
	** NOTE TO SPECIFIER ** Select Backsplash Type. Delete one of the next two paragraphs.
			14.	Backsplash: Attached coved backsplash with detached sidesplash.
			15.	Backsplash: Detached straight backsplash and sidesplash.
	** NOTE TO SPECIFIER ** Select Front Apron Type. Delete three of the next four paragraphs.
			16.	Front Apron: Flush.
			17.	Front Apron: Reveal, 3/8 inch x 1/8 inch (10 mm x 3 mm).
			18.	Front Apron: Setback.
			19.	Front Apron: Detached setback.
	** NOTE TO SPECIFIER ** Select Lavatory and Sink mounting method. Delete four of the next five paragraphs.
			20.	Sink Mounting: Integrally bonded - Roundover perimeter.
			21.	Sink Mounting: Integrally bonded - Bevel perimeter.
			22.	Sink Mounting: Integrally bonded - S-curve perimeter.
			23.	Sink Mounting: Mechanically fastened and sealed - Bullnose.
			24.	Sink Mounting: Mechanically fastened and sealed - Double 1/4 inch (6 mm) radius.
	** NOTE TO SPECIFIER ** Delete this entire article if Wall Panels or Sheet Stock is not required.
	2.5	WALL PANELS / SHEET STOCK
		A.	PRISM Wall cladding/wainscoting: Provide wall cladding/wainscoting from 1/4 inch (6 mm) solid surface panels. Butt panel joints and seal with silicone sealant. Adhere Panels only with silicone adhesive.
	** NOTE TO SPECIFIER ** Delete patterns not required.
			1.	Pattern: 4 inch (102 mm) squares.
			2.	Pattern: Diamond Accent Listello.
			3.	Pattern: 8 inch (203 mm) squares.
			4.	Pattern: Diamond.
			5.	Pattern: 6 inches (152 mm) x 24 inches (610 mm) horizontal.
			6.	Pattern: Beadboard.
			7.	Pattern: 3 inches (76 mm) x 6 inches (152 mm) Subway.
			8.	Pattern: Plankboard.
			9.	Pattern: 12 inch (305 mm) squares.
			10.	Pattern: Diamond Accent.
			11.	Pattern: Eclipse.
			12.	Pattern: Matrix.
			13.	Pattern: Tudor.
			14.	Pattern: Smooth Panel.
		B.	Wall Panel Accessories:
			1.	Outside Corner Molding: 1 inch x 1 inch x 1/4 inch x 96 inches (25 mm x 25 mm x 6 mm x 2438 mm).
			2.	Batten Strip: 2-1/2 inches x 1/4 inch x 96 inches (64 mm x 6 mm x 2438 mm).
			3.	Perimeter Trim, 2-1/2 inches x 1/4 inch x 96 inches (64 mm x 6 mm x 2438 mm).
			4.	Solid Surface Bonding Adhesive: 9.8 ounce (278 g).
			5.	Adhesive Cartridge Dispenser.
			6.	Adhesive Mixing Tips.
			7.	Silicone Sealant:
			8.	Inside Corner Molding: Trapezoid-shaped corner molding, 3/4 inch (19 mm) from corner x 1 inch (25 mm) thick x 96 inches (2438 mm) h.
	** NOTE TO SPECIFIER ** Delete this entire article if Window Sills are not required.
	2.6	WINDOW SILLS
		A.	PRISM Solid Surface Window Sills: PRISM Solid Surface fabricated to size and shape as specified on the Architect's Drawings. Seams shall be adhesively joined and inconspicuous.
	** NOTE TO SPECIFIER ** Delete one of the two following paragraphs.
			1.	Window Sill Thickness: 1/2 inch (12 mm).
			2.	Window Sill Thickness: 3/4 inch (19 mm).
		B.	Window Sill Accessories:
			1.	Solid Surface Bonding Adhesive: 9.8 ounce (278 g).
			2.	Adhesive Cartridge Dispenser.
			3.	Adhesive Mixing Tips.
			4.	Silicone Sealant.
	2.7	CUSTOM FABRICATIONS
		A.	Tub and shower walls: Provide Tub and Shower Walls from 1/4 inch (6mm), panels of PRISM Solid Surface.
		B.	Wall cladding/wainscoting: Provide wall cladding/wainscoting from 1/4 inch (6 mm), panels of PRISM Solid Surface. Panels shall have butt joints sealed with silicone sealant. Panels are to be adhered with silicone adhesive.
		C.	Bumper rails: Provide bumper rails from 1/2 inch or (12 mm) PRISM Solid Surface to size and shape as specified on the Architect's Drawings. Bumper rails shall have inconspicuous seams. Bumper rails are to be adhered with adhesive.
	** NOTE TO SPECIFIER ** Delete six of the next seven paragraphs.
			1.	Edge Treatment: Double Eased - 1/8 inch (3 mm) Radius.
			2.	Edge Treatment: Double Radius - 1/4 inch (6 mm) Radius.
			3.	Edge Treatment: Bevel - 1/4 inch (6 mm) Bevel.
			4.	Edge Treatment: Double Bevel - 1/4 inch (6 mm) Bevel.
			5.	Edge Treatment: S-Curve.
			6.	Edge Treatment: Classic Ogee.
			7.	Edge Treatment: Full Bullnose.
		D.	Laboratory countertops: Provide laboratory counter tops with 1/2 inch (12 mm) PRISM Solid Surface. Seams shall be adhesively joined and inconspicuous.
	** NOTE TO SPECIFIER ** Select Edge Type. Delete one of the next two paragraphs.
			1.	Edge Type: Standard Edge, with bottom perimeter pad of MDF.
			2.	Edge Type: Upgrade Edge, with edge inlay option.
	** NOTE TO SPECIFIER ** Delete six of the next seven paragraphs.
			3.	Edge Treatment: Double Eased - 1/8 inch (3 mm) Radius.
			4.	Edge Treatment: Double Radius - 1/4 inch (6 mm) Radius.
			5.	Edge Treatment: Bevel -1/4 inch (6 mm) Bevel.
			6.	Edge Treatment: Double Bevel - 1/4 inch (6 mm) Bevel.
			7.	Edge Treatment: S-Curve.
			8.	Edge Treatment: Classic Ogee.
			9.	Edge Treatment: Full Bullnose.
		E.	Reception areas/nurses' stations: Provide horizontal surfaces of reception areas/nurses' stations with 1/2 inch (12 mm) PRISM Solid Surface vertical surfaces shall be 1/4 inch (6 mm) PRISM Solid Surface. Seams shall be adhesively joined and inconspicuous.
	** NOTE TO SPECIFIER ** Select Edge Type. Delete one of the next two paragraphs.
			1.	Edge Type: Standard Edge, with bottom perimeter pad of MDF.
			2.	Edge Type: Upgrade Edge, with edge inlay option.
	** NOTE TO SPECIFIER ** Delete six of the next seven paragraphs.
			3.	Edge Treatment: Double Eased - 1/8 inch (3 mm) Radius.
			4.	Edge Treatment: Double Radius - 1/4 inch (6 mm) Radius.
			5.	Edge Treatment: Bevel - 1/4 inch (6 mm) Bevel.
			6.	Edge Treatment: Double Bevel - 1/4 inch (6 mm) Bevel.
			7.	Edge Treatment: S-Curve.
			8.	Edge Treatment: Classic Ogee.
			9.	Edge Treatment: Full Bullnose.
		F.	Table Tops: Provide table tops with 1/2 inch (12 mm) PRISM Solid Surface. Seams shall be adhesively joined and inconspicuous.
	** NOTE TO SPECIFIER ** Select Edge Type. Delete one of the next two paragraphs.
			1.	Edge Type: Standard Edge, with bottom perimeter pad of MDF.
			2.	Edge Type: Upgrade Edge, with edge inlay option.
	** NOTE TO SPECIFIER ** Delete six of the next seven paragraphs.
			3.	Edge Treatment: Double Eased - 1/8 inch (3 mm) Radius.
			4.	Edge Treatment: Double Radius - 1/4 inch (6 mm) Radius.
			5.	Edge Treatment: Bevel - 1/4 inch (6 mm) Bevel.
			6.	Edge Treatment: Double Bevel - 1/4 inch (6 mm) Bevel.
			7.	Edge Treatment: S-Curve.
			8.	Edge Treatment: Classic Ogee.
			9.	Edge Treatment: Full Bullnose.
		G.	Bar Tops: Provide bar tops with 1/2 inch (12 mm) PRISM Solid Surface. Seams shall be adhesively joined and inconspicuous.
	** NOTE TO SPECIFIER ** Select Edge Type. Delete one of the next two paragraphs.
			1.	Edge Type: Standard Edge, with bottom perimeter pad of MDF.
			2.	Edge Type: Upgrade Edge, with edge inlay option.
	** NOTE TO SPECIFIER ** Delete six of the next seven paragraphs.
			3.	Edge Treatment: Double Eased - 1/8 inch (3 mm) Radius.
			4.	Edge Treatment: Double Radius - 1/4 inch (6 mm) Radius.
			5.	Edge Treatment: Bevel -1/4 inch (6 mm) Bevel.
			6.	Edge Treatment: Double Bevel - 1/4 inch (6 mm) Bevel.
			7.	Edge Treatment: S-Curve.
			8.	Edge Treatment: Classic Ogee.
			9.	Edge Treatment: Full Bullnose.
		H.	Cold Cafeteria Surfaces: Provide surfaces with 1/2 inch (12 mm) PRISM Solid Surface. Seams shall be adhesively joined and inconspicuous. Fabricator to reinforce joints and cutouts as required and provide insulation between solid surface material and adjacent cold pans. Adequately insulate and isolate hot and cold areas.
	** NOTE TO SPECIFIER ** Select Edge Type. Delete one of the next two paragraphs.
			1.	Edge Type: Standard Edge, with bottom perimeter pad of MDF.
			2.	Edge Type: Upgrade Edge, with edge inlay option.
	** NOTE TO SPECIFIER ** Delete six of the next seven paragraphs.
			3.	Edge Treatment: Double Eased - 1/8 inch (3 mm) Radius.
			4.	Edge Treatment: Double Radius - 1/4 inch (6 mm) Radius.
			5.	Edge Treatment: Bevel - 1/4 inch (6 mm) Bevel.
			6.	Edge Treatment: Double Bevel - 1/4 inch (6 mm) Bevel.
			7.	Edge Treatment: S-Curve.
			8.	Edge Treatment: Classic Ogee.
			9.	Edge Treatment: Full Bullnose.
		I.	Hot Cafeteria Surfaces: Provide surfaces with 1/2 inch (12 mm) PRISM Solid Surface. Provide expansion joints in countertop as detailed on the Architect's Drawings. Fabricator to reinforce joints and cutouts as required and provide insulation between solid surface material and adjacent cold pans. Adequately insulate and isolate hot and cold areas. Vent cabinets as required.
	** NOTE TO SPECIFIER ** Select Edge Type. Delete one of the next two paragraphs.
			1.	Edge Type: Standard Edge, with bottom perimeter pad of MDF.
			2.	Edge Type: Upgrade Edge, with edge inlay option.
	** NOTE TO SPECIFIER ** Delete six of the next seven paragraphs.
			3.	Edge Treatment: Double Eased - 1/8 inch (3 mm) Radius.
			4.	Edge Treatment: Double Radius - 1/4 inch (6 mm) Radius.
			5.	Edge Treatment: Bevel - 1/4 inch (6 mm) Bevel.
			6.	Edge Treatment: Double Bevel - 1/4 inch (6 mm) Bevel.
			7.	Edge Treatment: S-Curve.
			8.	Edge Treatment: Classic Ogee.
			9.	Edge Treatment: Full Bullnose.
		J.	Cove Backsplash: Provide cove backsplash from 1/2 inch (12 mm) PRISM Solid Surface. 1/2 inch (12 mm) cove radius at the intersection of counter and backsplash.
		K.	Colored Inlays: Provide colored inlays that have a maximum groove depth of 1/8 inch (3mm). Groove shall be filled with color selected by architect and sanded smooth to match surrounding solid surface material.
		L.	Shower Receptor/Base: Provide poured-mold solid surface custom ADA or custom non-ADA: Up to 25 square feet (maximum mold size: 90 inches (2286 mm) x 114 inches (2896 mm) - drain minimum 7.25 inches (184 mm) from edge, featuring a non-skid surface, and integral water barrier. Non-skid surface to meet coefficient of friction of not less than .38 in compliance with ASTM F 462.
		M.	Decorative Panels: Provide 1/4 inch (6 mm) thick sheet routed in a tile-like pattern without seams or grout, custom sizes up to 48 inches (1219 mm) wide and 144 inches (3658 mm) long. Seamed panels up to 60 inches (1524 mm) wide 96 inches (2438 mm) long. Seams shall be adhesively joined and inconspicuous.
		N.	Accessories:
			1.	Outside Corner Molding: 1 inch x 1 inch x 1/4 inch x 96 inch (25 mm x 25 mm x 6 mm x 2438 mm).
			2.	Batten Strip: 2-1/2 inch x 1/4 inch x 96 inch (64 mm x 6 mm x 2438 mm).
			3.	Perimeter Trim, 2-1/2 inch x 1/4 inch x 96 inch (64 mm x 6 mm x 2438 mm).
			4.	Solid Surface Bonding Adhesive: 9.8 ounce (278 g).
			5.	Adhesive Cartridge Dispenser.
			6.	Adhesive Mixing Tips.
			7.	Silicone Sealant.
			8.	Inside Corner Molding: Trapezoid-shaped corner molding, 3/4 inch (19 mm) from corner x 1 inch (25 mm) thick x 96 inch (2438 mm) h.
	2.8	FINISHES
		A.	Colors: Provide surfaces in colors as follows:
	** NOTE TO SPECIFIER ** Select color requirement, and Insert specific color where already selected. Delete two of the next three paragraphs.
			1.	As selected from manufacturer's standard palette of colors.
			2.	As noted on the Finish Schedule of the Contract Drawings.
			3.	Color: ________________.
			4.	Finish: ________________.
	2.9	ACCESSORIES
		A.	Provide appropriate fasteners and accessories as required to properly complete installation.
	PART 3	EXECUTION
	3.1	EXAMINATION
		A.	Do not begin installation until substrates have been properly prepared.
		B.	If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
	3.2	PREPARATION
		A.	Clean surfaces thoroughly prior to installation.
		B.	Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
	3.3	INSTALLATION
		A.	Install in accordance with manufacturer's instructions.
	3.4	PROTECTION
		A.	Protect installed products until completion of project.
		B.	Touch-up, repair or replace damaged products before Substantial Completion.
	3.5	ADJUSTING AND CLEANING
		A.	Verify that surfaces are level, plumb and rigidly secured to substrate; make any adjustments required.
		B.	Clean finished surfaces and immediate areas of installation, using materials and methods recommended by manufacturer. Remove from project site packaging and debris caused by installation.
	END OF SECTION