MasterFormat: 95

SpecWizard: customize this spec    Download this Vinyl Windows Specification for   WORD | WP | RTF | TEXT

Find over 500 more construction specifications | Arcat.com

	SECTION 08560
	VINYL WINDOWS
	Copyright 2006 - 2007 ARCAT, Inc. - All rights reserved
	** NOTE TO SPECIFIER ** Harvey Building Products ; Vinyl Windows.
	This section is based on the products of Harvey Building Products , which is located at:
	1400 Main Street. Waltham, MA 02451-1623. Tel: (800) 598-5400. Fax: (781) 398-7749. E-mail: architects@harveybp.com. www.harveybp.com. Harvey Building Products is the leading manufacturer of insulating windows and doors and the premier wholesale distributor of quality building products in the Northeastern part of the United States. Distribution is primarily professional contractors and builders via strategically located branches as well as an extensive fleet of company owned trucks.
	PART 1	GENERAL
	1.1	SECTION INCLUDES
	** NOTE TO SPECIFIER ** Delete items below not required for project.
		A.	Vinyl New Construction Windows.
		B.	Vinyl Replacement Windows.
	1.2	RELATED SECTIONS
	** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
		A.	Section 03300: Cast-In-Place Concrete.
		B.	Section 04810: Unit Masonry Assemblies.
		C.	Section 06100: Rough Carpentry.
		D.	Section 06200: Finish Carpentry.
		E.	Section 07460: Siding.
	1.3	REFERENCES
	** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
		A.	ANSI/AAMA/NWWDA 101/I.S.2; 97 and current A-440-05 - Voluntary Specification for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors with revisions contained in "reprinting" of 12/99.
		B.	AAMA 701/702 - Combined Voluntary Specifications for Pile Weather strip and Replaceable Fenestration Weather seals.
		C.	AAMA 902 - Voluntary Specification for Sash Balances.
		D.	ASTM E 283 - Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls and Doors Under Specified Pressure Differences Across the Specimen.
		E.	ASTM E 330 - Standard Test Method for Structural Performance of Exterior Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference.
		F.	ASTM E 547 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Cyclic Static Air Pressure Difference.
		G.	ASTM E 1886 - Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials.
		H.	ASTM E 1996 - Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes.
		I.	ASTM E 2190 - Standard Specification for the Classification of the Durability of Sealed Insulating Glass Units.
		J.	ASTM F 588 - Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies, Excluding Glazing Impact.
		K.	NFRC 100/200 – Procedure for Determining Fenestration Product U-Factors and Solar Heat Gain.
	1.4	SUBMITTALS
		A.	Submit under provisions of Section 01300.
		B.	[ Product Data ]: Submit the following documents for each type of window.
			1.	Manufacturer's technical data, product descriptions and installation guides.
			2.	Elevation for each style window specified indicating its size, glazing type, muntin type and design.
			3.	Manufacturer's head, jamb and sill details for each window type specified.
	** NOTE TO SPECIFIER ** Delete selection samples if Colors have already been selected.
		C.	Selection Samples: For each finish product specified, a complete set of Color chips representing manufacturer's full range of available Colors.
		D.	Verification Samples: Provide operating units of each style window specified.
			1.	Verification samples may be operating scaled-down mock-ups of actual-size units.
			2.	Operating hardware such as balances, sash locks and weather-stripping.
			3.	Verification samples will be returned to manufacturer's representative at project closeout.
		E.	Test Reports: Submit certified independent testing agency reports indicating window units meet or exceed specified performance requirements.
	1.5	QUALITY ASSURANCE
		A.	Manufacturer Qualifications: Minimum ten (10) years producing vinyl (PVC) windows.
		B.	Installer Qualifications: Utilize an installer having demonstrated experience on projects of similar size.
		C.	Source Limitations: Obtain window units from one manufacturer through a single source.
		D.	Provide window units independently tested and found to be in compliance with ANSI/AAMA/NWWDA 101/I.S.2-97 and current A440-05 performance standards listed above.
		E.	Code Compliance: Provide windows that are labeled in compliance with the jurisdiction having authority over the project.
	** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.
		F.	Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.
			1.	Finish areas designated by Architect.
			2.	Do not proceed with remaining work until workmanship and color are approved by Architect.
			3.	Refinish mock-up area as required to produce acceptable work.
	1.6	DELIVERY, STORAGE, AND HANDLING
		A.	Deliver windows to project site in undamaged condition; handle windows to prevent damage to components and to finishes.
		B.	Store products in manufacturer's unopened packaging, out of direct sunlight or high temperature locations, until ready for installation.
	1.7	PROJECT CONDITIONS
		A.	Maintain environmental conditions (temperature, humidity and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.
	1.8	WARRANTY
		A.	Submit manufacturer's standard warranty against defects in workmanship and materials.
	** NOTE TO SPECIFIER ** Select project type. Delete one of the following two paragraphs. Select paragraph 1 for Residential applications or Paragraph 2 for commercial applications.
			1.	Limited Lifetime Limited Transferable warranty on extruded solid vinyl member and component parts. Insulated glass is warranted against material obstruction of transparency resulting from film formation or dust collection on the interior glass surfaces for a period of twenty (20) years. Consult warranty for complete details.
			2.	The warranty period for commercial project work such as apartments, housing authorities and other buildings not used by individual homeowners is 10 years, covering all vinyl, glass and component parts. Consult warranty for complete details.
	PART 2	PRODUCTS
	2.1	MANUFACTURERS
		A.	Acceptable Manufacturer: Harvey Building Products , which is located at: 1400 Main St. ; Waltham, MA 02451-9180; Toll Free Tel: 800-598-5400; Tel: 781-398-7800; Email: request info; Web: www.harveybp.com
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
		B.	Substitutions: Not permitted.
		C.	Requests for substitutions will be considered in accordance with provisions of Section 01600.
		D.	Substitutions must be submitted to Architect two weeks prior to bid opening.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION single hung windows are specified.
	2.2	NEW CONSTRUCTION HARVEY SINGLE HUNG WINDOW
		A.	Construction: Frame and top sash: Nominal 0.065 inch (1.8mm) frame thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Top lite to be integral to frame.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			1.	Siding Attachment: Integral 13/16 inch (21mm) "J" fin pocket.
			2.	Siding Attachment: L-fin (Integral J w/ L-adapter).
			3.	Color: White.
			4.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and glazing bead. Complies with ASTM E 2190.
			5.	Sash Balances: Factory calibrated block and tackle, complying with AAMA-902. Balance cords shall be anchored to glass filled nylon terminal housings that lock in place once the sash is tilted in. The locking terminal and pivot bar system shall be designed to positively interlock, to provide accurate alignment of the sash and the frame during installation and operation.
			6.	Top Glass - Fixed.
			7.	Sash Locks: Low profile composite sweep lock which anchors into the integrated keeper groove of the meeting rail frame. Double locks where openings exceed 30 1/4 inches (768mm) wide.
			8.	Weather Stripping: In compliance with AAMA 701.2.
			9.	Screens: Roll form aluminum frame, half screen with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete one of the next two paragraphs or both if not required.
			10.	Grids: Colonial contour grids between glass (GBG) dividers.
			11.	Grids: Flat diamond grids between glass (GBG) dividers.
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP30 Rating is required.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.05 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 4.60 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 45.14 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R30 (DP30)- Test Size: 42 inches x 77 inches (1166mm x 1955mm) in accordance with AAMA/WDMA/CSA 101/I.S.2 A440-05.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.49 / R-Value - 2.04 / SHGC - 0.61 / VT - 0.64.
				b.	Low-E: U-Factor - 0.35 / R-Value - 2.86/ SHGC - 0.31. / VT - 0.57
				c.	Low-E/Argon: U-Factor - 0.32 / R-Value - 3.12/ SHGC - 0.31 / VT - 0.57.
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP50 Rating is required.
		C.	Performance:
			1.	Air Infiltration: Maximum 0.05 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 75.24 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R50 (DP50)- Test Size: 42 inches x 77 inches (1166mm x 1955mm) in accordance with AAMA/WDMA/CSA 101/I.S.2 A440-05.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear DSB: U-Factor - 0.50 / R-Value - 2.00 / SHGC - 0.61 / VT - 0.64.
				b.	Low-E DSB: U-Factor - 0.36 / R-Value - 2.78 / SHGC - 0.31 / VT - 0.55.
				c.	Low-E/Argon DSB: U-Factor - 0.33 / R-Value - 3.03 / SHGC - 0.30 / VT - 0.55
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION Tribute double hung windows are specified.
	2.3	NEW CONSTRUCTION TRIBUTE DOUBLE HUNG WINDOWS
		A.	Construction:
			1.	Nominal 0.070 inch (1.8mm) frame thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Operable sash shall be a nominal 0.070 inch (1.8mm) thickness and fusion welded corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) “J” fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete two of the next three paragraphs.
			4.	Color: White.
			5.	Color Option: Custom Exterior Finish.
			6.	Color Option: Custom Interior Finish - Better Grain (dark oak, red cedar, pine).
			7.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and rigid PVC glazing bead. SunClean coating is applied to exterior surface. Complies with ASTM E 2190.
			8.	Sash Balances: Factory calibrated block and tackle, complying with AAMA-902. Balance cords shall be anchored to locking terminal housings when the sash is tilted in. The locking terminal and pivot bar system shall provide accurate alignment of the sash and the frame during operation.
			9.	Locks: Two low-profile sash locks to operate the tilt release latches allowing the sash to tilt in.
			10.	Weather Stripping: In compliance with AAMA 701.2.
			11.	Screens: Extruded aluminum full screen with VIEWS (Virtually invisible enhanced window screen).
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			12.	Grids: Colonial contour grids between glass (GBG) dividers.
			13.	Grids: Flat diamond grids between glass (GBG) dividers.
			14.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			15.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP35 Rating is required.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.07cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water resistance: no leakage when tested at 5.43 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 52.66 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-LC35 (DP 35) - Test Size: 48 inches x 84 inches (1118mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2 /A440-05.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified. Delete one of the next two paragraphs.
				a.	Low-E/Argon SunClean: U-Factor - 0.30 / R-Value - 3.33/ SHGC - 0.25 / VT - 0.45.
				b.	HP TG 2XLow E/Krypton SunClean and Climaguard: U-Factor - 0.22 / R-Value - 4.54 / SHGC - 0.21 / VT - 0.36.
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP50 Rating is required.
		C.	Performance:
			1.	Air Infiltration: Maximum 0.05cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water resistance: no leakage when tested at 7.52 psf in accordance with ASTM E-547.
			3.	Uniform structural test pressure at 74.24 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-LC 50 (DP 50) - Test Size: 42 inches x 77 inches (1118mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2 /A440-05.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and 200.
	** NOTE TO SPECIFIER ** Select glazing type specified. Delete one of the next two paragraphs.
				a.	Low-E/Argon SunClean: U-Factor - 0.30 / R-Value - 3.33/ SHGC - 0.25/ VT - 0.45.
				b.	HP TG 2xLow E/Krypton SunClean and Climaguard: U-Factor - 0.22 / R-Value - 4.54/ SHGC - 0.21 / VT - 0.36.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION Vicon double hung windows are specified.
	2.4	NEW CONSTRUCTION VICON DOUBLE HUNG WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.070 inch (1.8mm) frame thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Sash shall be a nominal 0.065 inch (1.7mm) thickness and fusion welded corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) "J" fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** Frame color options - Delete one of the next two paragraphs.
			4.	Color: White.
			5.	Color: Almond.
			6.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and dual durometer glazing bead. Complies with ASTM E 2190.
			7.	Sash Balances: Factory calibrated block and tackle, complying with AAMA-902. Balance cords shall be anchored to glass filled nylon terminal housings that lock in place once the sash is tilted in. The locking terminal and pivot bar system shall be designed to positively interlock, to provide accurate alignment of the sash and the frame during installation and operation.
			8.	Sash Locks: Knife type locks anchored with screws driven through the sash rail and into an extruded aluminum reinforcing bar. Double locks where openings exceed 30 1/4 inches (768mm) wide.
			9.	Weather Stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Select Screens - Delete one of the following two paragraphs
			10.	Screens: Extruded aluminum full screen with 18 x 16 charcoal finished fiberglass mesh.
			11.	Screens: Extruded aluminum half screen with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete one of the next two paragraphs or both if not required.
			12.	Grids: Colonial contour grids between glass (GBG) dividers.
			13.	Grids: Flat diamond grids between glass (GBG) dividers.
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP35 Rating is required.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.12 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 5.25 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 45.0 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R35 (DP35) - Test Size: 42 inches x 77 inches (1066.8mm x 1955.8mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC ): 28 and 35.
			7.	Thermal Transmittance: Tested in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the following three paragraphs.
				a.	Clear: U-Factor - 0.48 / R-Value - 2.08/ SHGC - 0.61 VT - 0.64.
				b.	Low-E: U-Factor - 0.34 / R-Value - 2.94/ SHGC - 0.31 / VT - 0.56.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33/ SHGC - 0.31 / VT - 0.56
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP50 Rating is required.
		C.	Performance:
			1.	Air Infiltration: Maximum 0.22 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 75.24psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R50 (DP50) - Test Size: 40 inches x 63 inches (1168mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC ) 28 and 35.
			7.	Thermal Transmittance: Tested in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the following three paragraphs.
				a.	Clear DSB: U-Factor - 0.49 / R-Value - 2.04/ SHGC - 0.59 / VT - 0.63.
				b.	Low-E DSB: U-Factor - 0.35 / R-Value - 2.86/ SHGC - 0.31 / VT - 0.56.
				c.	Low-E/Argon DSB: U-Factor - 0.30 / R-Value - 3.33/ 0.30 / VT - 0.56
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION Vicon Classic double hung windows are specified.
	2.5	NEW CONSTRUCTION VICON CLASSIC DOUBLE HUNG WINDOWS
		A.	Construction:
			1.	Nominal 0.070 inch (1.8mm) frame thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Operable sash shall be a nominal 0.065 inch (1.7mm) thickness and fusion welded corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) "J" fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** Frame color options – Delete four of the next five paragraphs and insert custom color from manufacturer's available options where required.
			4.	Color: White.
			5.	Color: Almond.
			6.	Color: Bronze.
			7.	Color: Custom Exterior Finish.
			8.	Color: Custom Interior Finish - Better Grain (dark oak, red cedar, pine).
			9.	Glazing: Insulated glass units secured to sash frame using a sealant and dual durometer glazing bead. Complies with ASTM E 2190.
			10.	Sash Balances: Factory calibrated block and tackle, complying with AAMA-902. Balance cords shall be anchored to locking terminal housings when the sash is tilted in. The locking terminal and pivot bar system shall provide accurate alignment of the sash and the frame during operation.
			11.	Sash Locks: Cam type locks anchored with screws driven through the sash rail and into an extruded aluminum reinforcing bar. Double locks where openings exceed 30 1/4 inches (768mm) wide.
			12.	Weather Stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Select Screens - Delete three of the following four paragraphs
			13.	Screens: Extruded aluminum full screen with 18 x 16 charcoal finished fiberglass mesh.
			14.	Screens: Extruded aluminum half screen with 18 x 16 charcoal finished fiberglass mesh.
			15.	Screens: Extruded aluminum full screen with 18 x 16 charcoal finished aluminum mesh.
			16.	Screens: Extruded aluminum half screen with 18 x 16 charcoal finished aluminum mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			17.	Grids: Colonial contour grids between glass (GBG) dividers.
			18.	Grids: Flat diamond grids between glass (GBG) dividers.
			19.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			20.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
	** NOTE TO SPECIFIER ** Select the following paragraph if DP35 Rating is required.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.19 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water resistance: no leakage when tested at 5.25 psf in accordance with ASTM E-547.
			3.	Uniform structural test pressure at 52.5 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R35 (DP35) - Test Size: 44 inches x 60 inches (1118mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class: (STC) 28 and 35.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.48 / R-Value - 2.08/ SHGC - 0.59 / VT - 0.62.
				b.	Low-E: U-Factor - 0.34 / R-Value - 2.94 / SHGC - 0.30 / VT - 0.55.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.30 / VT - 0.55.
	** NOTE TO SPECIFIER ** Select the following paragraph if DP40 Rating. Reinforcements are required.
		C.	Performance:
			1.	Air infiltration maximum .014 CFM/sq. ft. at 1.57 psf (25mph) in accordance with ASTM E -283.
			2.	Water Resistance: No leakage when tested at 6.0 psf in accordance with ASTM E-547.
			3.	Uniform structural test pressure at 60.0 psf positive and negative in accordance with ASTM E 330.
			4.	Structural rating H-R 40 (DP40) - Test Size: 44 inches x 60 inches (1118mm x 1524mm) in accordance with AWSI/AAMA/NWWDA. 101/IS.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 28 and 35.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.48 / R-Value - 2.08 / SHGC - 0.59 / VT - 0.62.
				b.	Low-E: U-Factor - 0.34 / R-Value - 2.94 / SHGC - 0.30 / VT - 0.55.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.30 VT - 0.55.
		D.	Performance:
			1.	Air infiltration maximum .008 CFM/sq. ft. at 1.57 psf (25mph) in accordance with ASTM E -283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E-547.
			3.	Uniform structural test pressure at 75.24 psf positive and negative in accordance with ASTM E 330.
			4.	Structural rating H-R 50 (DP50)- Test Size: 46 inches x 60 inches (1118mm x 1524mm) in accordance with AWSI/AAMA/NWWDA. 101/IS.2 /A440-05
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 28 and 35.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear DSB: U-Factor - 0.48 / R-Value - 2.08 / SHGC 0.57 / VT - 0.61.
				b.	Low-E DSB: U-Factor - 0.35 / R-Value - 2.86/ SHGC - 0.30 / VT - 0.54.
				c.	Low-E/Argon DSB: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.30 / VT - 0.55.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION impact double hung windows are specified.
	2.6	NEW CONSTRUCTION VIGILANCE IMPACT DOUBLE HUNG WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.070 inch (1.8mm) polyvinyl chloride (PVC) with miter cut ,fusion welded corners and reinforced. Operable sash shall be a nominal 0.065 inch (1.7mm) thickness, fusion welded corners and reinforced with extruded aluminum.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) “J” fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete one of the next two paragraphs.
			4.	Color: White.
			5.	Color: Custom Exterior Finish.
			6.	Glazing: Shall be 7/8 inch (22mm) insulating glass, 8.2mm laminated glass with 0.090 PVB Interlayer on inside and 1/8 inch (3mm) double strength annealed glass on outer layer. System is wet glazed with structural silicone. Complies with ASTM E2190
			7.	Sash Balances: Factory calibrated stainless steel constant force balance system.
			8.	Sash Locks: Heavy duty cam type locks anchored with screws driven through the sash rail and into an extruded aluminum reinforcing bar. Double locks where openings exceed 30 1/4 inches (768mm) wide.
			9.	Weather Stripping: Complies with AAMA 701.2. The sill and sash shall have a negative and positive interlock.
			10.	Screens shall be extruded aluminum half or full screen with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			11.	Grids: Colonial contour grids between glass (GBG) dividers.
			12.	Grids: Flat diamond grids between glass (GBG) dividers.
			13.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			14.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance
			1.	Air Infiltration maximum 0.10 cfm/sq.ft .at 1.57 psf in accordance with ASTM E-283.
			2.	Water Resistance: no leakage when tested at 9.20 psf in accordance with ASTM E 547.
			3.	Uniform Structural Test Pressure at 97.81 psf positive and negative in accordance with ASTM E 330.
			4.	Design Pressure DP65 (H-R65) Test Size 42x72 in accordance with AAMA/WDMA/CSA/101 I/S.2/ A-440-5.
			5.	Forced Entry: Type B Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 34.
			7.	Impact Resistance: Meets requirements of ASTM E 1886 and E 1996 for small and large missile impact.
			8.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	IR Clear - U-Factor - 0.45 / R-Value - 2.22 / SHGc - 0.52 / VT - 0.57.
				b.	IR Low-E - U-Factor - 0.34 / R-Value - 2.94 / SHGc - 0.28 / VT - 0.51.
				c.	IR Low-E/Argon: U-Factor - 0.29 / R-Value - 3.45 / SHGC - 0.20 / VT - 0.45.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION Tribute casement windows are specified.
	2.7	NEW CONSTRUCTION TRIBUTE CASEMENT WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) “J” fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete two of the next three paragraphs.
			4.	Color: White.
			5.	Color: Custom Exterior Finish.
			6.	Color: Custom Interior Finish - Better Grain (oak, red cedar, pine).
			7.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and rigid PVC glazing bead. SunClean coating is applied to exterior surface. Complies with ASTM E 2190.
			8.	Hinges: Maxim 14 series.
			9.	Sash Locks: Sequentially locking multi-point type with single handle actuator.
			10.	Operator: Maxim 50 series.
			11.	Weather stripping: In compliance with AAMA 701.2.
			12.	Screens: Extruded aluminum frame with VIEWS (Virtually invisible screen wire.)
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			13.	Grids: Colonial contour grids between glass (GBG) dividers.
			14.	Grids: Flat diamond grids between glass (GBG) dividers.
			15.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			16.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 60.15 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: C-40 (DP40) - Test Size: 36 inches x 80 inches (813mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 30 in accordance with ASTM F 588.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified. Delete one of the next two paragraphs.
				a.	Low-E/Argon SunClean: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.19 / VT - 0.34.
				b.	HP TG 2xLow E /Krypton SunClean and Climaguard: U-Factor - 0.22 / R-Value - 4.55/ SHGC - 0.17 / VT - 0.29.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION casement windows are specified.
	2.8	NEW CONSTRUCTION VICON CASEMENT WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) "J" fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			4.	Color: White.
			5.	Color: Almond.
			6.	Color: Bronze.
			7.	Color: Custom Exterior Finish.
			8.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and rigid PVC glazing bead. Complies with ASTM E 2190.
			9.	Hinges: Maxim 14 series.
			10.	Sash Locks: Sequentially locking multi-point type with single handle actuator.
			11.	Operator: Maxim 50 series.
			12.	Weather stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Screen Options - Delete one of the next two paragraphs.
			13.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
			14.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished aluminum mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			15.	Grids: Colonial contour grids between glass (GBG) dividers.
			16.	Grids: Flat diamond grids between glass (GBG) dividers.
			17.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			18.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP45 Rating is required.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 60.15 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: C-40 (DP 40) Test Size: 36 inches x 80 inches (914.4mm x 2032mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 30 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29 , 35 and 40.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the following three paragraphs.
				a.	Clear: U-Factor - 0.44 / R-Value - 2.27/ SHGC - 0.45 / VT - 0.47.
				b.	Low-E: U-Factor - 0.33 / R-Value - 3.03 / SHGC - 0.23 / VT -0.42.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33/ SHGC - 0.22 / VT - 0.37.
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP120 Rating is required.
		C.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.00 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 112.5 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: C-C120 (DP120) Test Size: 24 inches x 48 inches (610mm x 1219mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 30 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29, 35 and 40.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the following three paragraphs.
				a.	Clear: U-Factor - 0.44 / R-Value - 2.27 / SHGC - 0.45 / VT - 0.47.
				b.	Low-E: U-Factor - 0.33 / R-Value - 3.03 / SHGC - 0.23 / VT - 0.42.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.22 / VT - 0.37.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION impact casement windows are specified.
	2.9	NEW CONSTRUCTION VIGILANCE IMPACT CASEMENT WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Both sash and frame shall be reinforced with extruded aluminum.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) “J” fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete one of the next two paragraphs.
			4.	Color: White.
			5.	Color: Custom Exterior Finish.
			6.	Glazing: Shall be 7/8 inch (22mm) insulated glass, 8.2mm laminated with 0.090 inch PVB interlayer on inside and 1/8 inch (3mm) double strength annealed glass on outer layer. System shall be wet glazed with structural silicone. Complies with ASTM E2190.
			7.	Hinges: Stainless Steel Maxim 14 series.
			8.	Sash Locks: Sequentially locking multi-point type with single handle actuator.
			9.	Operator: Maxim 50 series.
			10.	Weather stripping: In compliance with AAMA 701.2.
			11.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			12.	Grids: Colonial contour grids between glass (GBG) dividers.
			13.	Grids: Flat diamond grids between glass (GBG) dividers.
			14.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			15.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 97.74 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: C-C65 (DP 65); Test Size: 32 inches by 65 inches 813mm x 651mm) in accordance with AAMA/NWWDA/CSA 101/I.S.2/A 440-05.
			5.	Forced Entry: Type B, Grade 30 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 34 and 37.
			7.	Impact Resistance: Meets requirements of ASTM E 1886 and E 1996 for small and large missile impact.
			8.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete one of the following two paragraphs.
				a.	Clear: U-Factor - 0.43 / R-Value - 2.32 / SHGc - 0.45 / VT - 0.47.
				b.	Low-E/Argon: U-Factor 0.30 / R-Value - 3.33 / SHGC - 0.26 / VT - 0.47.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION Tribute awning windows are specified.
	2.10	NEW CONSTRUCTION TRIBUTE AWNING WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) “J” fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete two of the next three paragraphs.
			4.	Color: White.
			5.	Color: Custom Exterior Finish.
			6.	Color: Custom Interior Finish - Better Grain (red cedar, oak, pine).
			7.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and rigid PVC glazing bead. Sun clean coating is applied to exterior surface. Complies with ASTM E .2190.
			8.	Hinges: Maxim 13 series.
			9.	Sash Locks: Maxim 24 Series single point locks.
			10.	Weather stripping: In compliance with AAMA 701.2.
			11.	Screens: Extruded aluminum frame with VIEWS (Virtually invisible enhanced window screen.)
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			12.	Grids: Colonial contour grids between glass (GBG) dividers.
			13.	Grids: Flat diamond grids between glass (GBG) dividers.
			14.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			15.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at60.19 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: AP-LC40 –(DP 40) Test Size: 60 inches x 42 inches (1524mm x 1067mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 20 in accordance with ASTM F 588.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified. Delete one of the next two paragraphs.
				a.	2XLow-E/Argon SunClean: U-Factor 0.30 / R-Value - 3.33 / SHGC - 0.19 / VT - 0.34.
				b.	HPTG 2x Low E/Krypton SunClean and Climaguard: U-Factor 0.22 / R Value - 4.55 / SHGC - 0.17 / VT - 0.29.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION awning windows are specified.
	2.11	NEW CONSTRUCTION VICON AWNING WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) “J” fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			4.	Color: White.
			5.	Color: Almond.
			6.	Color: Bronze.
			7.	Color: Custom Exterior Finish.
			8.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and rigid PVC glazing bead. Complies with ASTM E 2190.
			9.	Hinges: Maxim 13 series.
			10.	Sash Locks: Maxim 24 Series single point locks.
			11.	Weather stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Screen Options - Delete one of the next two paragraphs.
			12.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
			13.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished aluminum mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			14.	Grids: Colonial contour grids between glass (GBG) dividers.
			15.	Grids: Flat diamond grids between glass (GBG) dividers.
			16.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			17.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 60.19 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: AP-LC40 (DP40) - Test Size: 60 inches x 42 inches (1524mm x 1067mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 20 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29 and 35.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete one of the following two paragraphs.
				a.	Clear: U-Factor - 0.44 / R-Value 2.27 / SHGC - 0.45 / VT - 0.47.
				b.	Low-E: U-Factor - 0.30 / R-Value - 3.33/ SHGC - 0.23 / VT - 0.42.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION impact awning windows are specified.
	2.12	NEW CONSTRUCTION VIGILANCE IMPACT AWNING WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Both sash and frame shall be reinforced with extruded aluminum.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) “J” fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete one of the next two paragraphs.
			4.	Color: White.
			5.	Color: Custom Exterior Finish.
			6.	Glazing: Shall be 7/8 inch (22mm) insulated glass, 8.2 laminated glass with PVB Interlayer on inside and 1/8” double strength annealed glass on outer layer. System shall be wet glazed with structural silicone. Complies with ASTM E 2190
				a.	Low-E with Argon.
			7.	Hinges: Stainless Steel Maxim 13 series.
			8.	Sash Locks: Maxim 24 Series single point locks.
			9.	Weather stripping: In compliance with AAMA 701.2.
			10.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			11.	Grids: Colonial contour grids between glass (GBG) dividers.
			12.	Grids: Flat diamond grids between glass (GBG) dividers.
			13.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			14.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 112.7 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: AP-LC75 (DP75) Test Size: 48 inches by 32 inches (1219mm x 813mm) in accordance with AAMA/NWWDA /CSA101/I.S.2 /A440-05.
			5.	Forced Entry: Type B, Grade 20 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 34 and 37.
			7.	Impact Resistance: Meets requirements of ASTM E 1886 and E 1996 for small and large missile impact.
			8.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the following three paragraphs.
				a.	Clear: U-Factor - 0.44 / R-Value - 2.27 / SHGc - 0.45 / VT - 0.47.
				b.	Low-E: U-Factor - 0.33 / R-Value - 3.33 / SHGc - 0.23 - VT - 0.42.
				c.	ENERGYSTAR rated Low-E w/argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.26 / VT - 0.42.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION hopper windows are specified.
	2.13	NEW CONSTRUCTION VICON HOPPER WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.065 inch (1.7mm) thickness polyvinyl chloride (PVC) with frame corners miter cut and fusion welded. Sash thickness .065 inch (1.7mm) with mechanically fastened corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Snap-on applied 3/4 inch (20mm) “J” fin.
			3.	Siding Attachment: Snap-on applied "L" fin.
	** NOTE TO SPECIFIER ** Frame color options – Delete two of the next three paragraphs and insert custom color from manufacturer's available options where required.
			4.	Color: White.
			5.	Color: Almond.
			6.	Color: Custom Exterior Finish.
			7.	Glazing: Insulated glass units secured to sash frame using a sealant in corners and u-channel glazing bead. Complies with ASTM E 2190.
			8.	Hinges: Stainless Steel Maxim 13 series.
			9.	Sash Locks: Knife type. Double locks where openings exceed 30 1/4 inches (768mm) wide.
			10.	Weather stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Screen Options - Delete one of the next two paragraphs.
			11.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
			12.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished aluminum mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete one of the next two paragraphs or both if not required.
			13.	Grids: Colonial contour grids between glass (GBG) dividers.
			14.	Grids: Flat diamond grids between glass (GBG) dividers.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.06 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 2.93 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 22.57 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: AP-R-15(DP15) - Test Size: 48 inches x 32 inches (1219mm x 1067mm) in accordance with AAMA/NWWDA/CSA101/IS2/A440-05 101/I.S.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 34 and 37.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the following three paragraphs.
				a.	Clear: U-Factor - 0.46 / R-Value - 2.17 / SHGC - 0.55 / VT - 0.57.
				b.	Low-E: U-Factor - 0.34 / R-Value - 2.94 / SHGC - 0.28 / VT - 0.50.
				c.	2x Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33/ SHGC - 0.26 / VT - 0.44.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION Tribute rolling windows are specified.
	2.14	NEW CONSTRUCTION TRIBUTE ROLLING WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.1 inch (2.5mm) thickness polyvinyl chloride (PVC). Sill and jamb corners miter cut and fusion welded. Head frame and jamb butt jointed and mechanically fastened. Sash thickness a nominal 0.078 inch (2mm) with miter cut and mechanically fastened corners.
	** NOTE TO SPECIFIER ** Select Siding attachment. Delete one of the next two paragraphs.
			2.	Siding Attachment: Snap-on applied 3/4 inch (20mm) "J" fin.
			3.	Siding Attachment: Snap-on L-fin.
	** NOTE TO SPECIFIER ** White is standard. Custom colors are available. Insert custom color from manufacturer's available options. Delete two of the next three paragraphs.
			4.	Color: White.
			5.	Color: Custom Exterior Finish.
			6.	Color: Custom Interior Finish - Better Grain (dark oak, red cedar, pine).
			7.	Glazing: Insulated glass units secured to sash frame using a sealant in the corners and dual durometer U-channel glazed. SunClean coating is applied to exterior surface. Complies with ASTM E 2190.
			8.	Sash Locks: Cam type. Double locks where openings exceed 36 3/8 inches (924mm) height.
			9.	Weather stripping: In compliance with AAMA 701.2.
			10.	Screens: Extruded aluminum frame with VIEWS (Virtually Invisible Enhanced Window Screen.)
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			11.	Grids: Colonial contour grids between glass (GBG) dividers.
			12.	Grids: Flat diamond grids between glass (GBG) dividers.
			13.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			14.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.08 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 6.0 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 52.5 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: HS-LC35 (DP 35) Test Size: 78 inches x 64 inches (1981mm x 1626mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type D, Grade 20 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified. Delete one of the next two paragraphs.
				a.	2xLow-E/Argon SunClean: U-Factor - 0.32 / R-Value - 3.12 / SHGC - 0.26 / VT - 0.44.
				b.	HP TG 2X Low E/ Krypton-SunClean and Climaguard: U-Factor - 0.22 / R Value - 4.54 / SHGC - 0.24 / VT - 0.39.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION rolling windows are specified.
	2.15	NEW CONSTRUCTION VICON ROLLING WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.1 inch (2.5mm) thickness polyvinyl chloride (PVC). Sill and jamb corners miter cut and fusion welded. Head frame and jamb butt jointed and mechanically fastened. Sash thickness a nominal 0.078 inch (2mm) with miter cut and mechanically fastened corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Snap-on applied 3/4 inch (20mm) “J” fin.
			3.	Siding Attachment: Snap-on applied "L" fin.
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			4.	Color: White.
			5.	Color: Almond.
			6.	Color: Bronze.
			7.	Color: Custom Exterior Finish.
			8.	Glazing: Insulated glass units secured to sash frame using a sealant in the corners and dual durometer U-channel glazed. Complies with ASTM E 2190.
			9.	Sash Locks: Cam type. Double locks where openings exceed 36 3/8 inches (924mm) in height.
			10.	Weather stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Screen Options - Delete one of the next two paragraphs.
			11.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
			12.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished aluminum mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			13.	Grids: Colonial contour grids between glass (GBG) dividers.
			14.	Grids: Flat diamond grids between glass (GBG) dividers.
			15.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			16.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
	** NOTE TO SPECIFIER ** Select the following paragraph for a DP 35 Rating. Reinforcement is required.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.08 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 6.0 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 52.5 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: HS-LC35 (DP 35) - Test Size: 78 inches x 64 inches (1981mm x 1626mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type D, Grade 20 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.49 / R-Value - 2.04 / SHGC - 0.62 / VT - 0.64.
				b.	Low-E: U-Factor - 0.36 / R-Value - 2.78/ SHGC - 0.32 / VT - 0.57.
				c.	TG 2xLow-E/Argon: U-Factor - 0.27 / R-Value - 3.70 / SHGC - 0.27 / VT - 0.46.
	** NOTE TO SPECIFIER ** Select the following paragraph if a DP40 Rating is required.
		C.	Performance:
			1.	Air Infiltration: Maximum 0.08 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 6.0 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 75.0 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: HS-LC40 (DP 40)- Test Size: 69 inches x 54 inches (1753mm x 1372mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type A, Grade 20 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.49 / R-Value - 2.04 / SHGC - 0.62.
				b.	Low-E: U-Factor - 0.36 / R-Value - 2.78 / SHGC - 0.32.
				c.	TG 2xLow-E/Argon: U-Factor - 0.27 / R-Value - 3.70 / SHGC - 0.27 / VT - 0.46.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION Tribute picture windows are specified.
	2.16	NEW CONSTRUCTION TRIBUTE PICTURE WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.070 inch (1.8mm) wall thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) “J” fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** White is standard. Custom colors are available. Insert custom color from manufacturer's available options. Delete two of the next three paragraphs.
			4.	Color: White.
			5.	Color: Custom Exterior Finish.
			6.	Color: Custom Interior Finish - Better Grain (red cedar, dark oak, pine).
			7.	Glazing: Insulated glass units secured to sash frame using a sealant in the corners and glazing bead. Sun clean coating is applied to exterior surface. Complies with ASTM E2190.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			8.	Grids: Colonial contour grids between glass (GBG) dividers.
			9.	Grids: Flat diamond grids between glass (GBG) dividers.
			10.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			11.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E 5400.
			3.	Uniform structural test pressure at 75.19 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: F-C50 - (DP 50) Test Size: 70 inches x 70 inches (1372mm x 1372mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Sound Transmission Class (STC): 29.
			6.	Forced Entry: Type D, Grade 40 in accordance with ASTM F 588.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified. Delete one of the next two paragraphs.
				a.	Low-E/Argon SunClean: U-Factor - 0.26 / R-Value - 3.85 / SHGC - 0.25 / VT - 0.44.
				b.	HP TG 2X Low E/Krypton SunClean and Climaguard: U-Factor - 0.16 / R Value - 5.55 /SHGC - 0.23 / VT - 0.40.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION picture windows are specified.
	2.17	NEW CONSTRUCTION VICON PICTURE WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.070 inch (1.8mm) wall thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) “J” fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			4.	Color: White.
			5.	Color: Almond.
			6.	Color: Bronze.
			7.	Color: Custom Exterior Finish.
			8.	Glazing: Insulated glass units secured to sash frame using a sealant in the corners and glazing bead. Complies with ASTM E 2190.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			9.	Grids: Colonial contour grids between glass (GBG) dividers.
			10.	Grids: Flat diamond grids between glass (GBG) dividers.
			11.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			12.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 75.19 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: F-C50 (DP50) - Test Size: 70 inches x 70 inches (1778mm x 1778mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type D, Grade 40 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.45 / R-Value - 2.2 2 / SHGC - 0.61 / VT - 0.65.
				b.	Low-E: U-Factor - 0.31 / R-Value - 3.23 / SHGC - 0.31 / VT - 0.58.
				c.	Low-E/Argon: U-Factor - 0.27 / R-Value - 3.70 / SHG c-0.31 / VT - 0.58.
	** NOTE TO SPECIFIER ** Delete the following article if no NEW CONSTRUCTION Designer Shapes windows are specified.
	2.18	NEW CONSTRUCTION VICON DESIGNER SHAPES WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.1 inch (2.5mm) wall thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Siding attachment options. Delete one of the next two paragraphs.
			2.	Siding Attachment: Integral 13/16 inch (21mm) “J” fin pocket.
			3.	Siding Attachment: L-fin (Integral J w/ L-adapter).
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			4.	Color: White.
			5.	Color: Almond.
			6.	Color: Bronze.
			7.	Color: Custom Exterior Finish.
			8.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and dual durometer glazing bead. Complies with ASTM E 2190.
	** NOTE TO SPECIFIER ** Grid options – Delete one of the next two paragraphs or both if not required.
			9.	Grids: Colonial contour grids between glass (GBG) dividers.
			10.	Grids: Flat diamond grids between glass (GBG) dividers.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 4.5 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 45.0 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: F-C30 (DP30) - Test Size: 64 inches x 64 inches (1626mm x 1626mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 40 in accordance with ASTM F 588.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.47 / R-Value - 2.13 / SHGC - 0.6 / VT - 0.71.
				b.	Low-E: U-Factor - 0.32 / R-Value - 3.13/ SHGC - 0.34 / VT - 0.63.
				c.	Low-E/Argon: U-Factor - 0.28/ R-Value - 3.57/ SHGC - 0.34 / 0.63.
	2.19	NEW CONSTRUCTION WINDOW ACCESSORIES
	** NOTE TO SPECIFIER ** Mullion options - Delete entire paragraph if mullions are not required.
		A.	Mullions:
	** NOTE TO SPECIFIER ** Common mulled units are available up to 130 inches wide. Delete two of the next three paragraphs.
			1.	Common Jamb: Windows are contained within single frame and separated by a common mull post.
			2.	Non-Structural Combination Mullion: horizontal or vertical members. May be factory or field applied.
	** NOTE TO SPECIFIER ** Casing options. Casings are not available with Vigilance windows. Delete entire paragraph if casings are not required or Vigilance windows are specified.
		B.	Casings: Factory installed casing options.
	** NOTE TO SPECIFIER ** Select casing – Delete three of the next four paragraphs.
			1.	2 3/8 inch (60mm) brick mold, nominal thickness 0.080 inches (2mm); 4 Sides.
			2.	2 3/8 inch (60mm) brick mold, nominal thickness 0.080 inches (2mm) with 1 inch (25mm) sill nosing.
			3.	3 inch (76mm) flat casing, nominal thickness 0.080 inches (2mm); 4 sides.
			4.	3 inch (76mm) flat casing, nominal thickness 0.080 inches (2mm) with 1 inch (25mm) sill nosing.
		C.	Extension Jambs:
	** NOTE TO SPECIFIER ** Delete extension jamb finish not specified.
			1.	Pre-Primed.
			2.	Clear Pine.
	** NOTE TO SPECIFIER ** Delete extension jambs not specified. Custom depths available up to 7 1/4 inches (184mm).
			3.	4-9/16 inch (116mm) depth (2 x 4 wall construction).
			4.	6-9/16 inch (167mm) depth (2 x 6 wall construction).
			5.	Custom Depth: __________.
	** NOTE TO SPECIFIER ** Delete the following article if no patio doors are specified.
	2.20	SLIDING PATIO DOORS
		A.	Construction:
			1.	Frame and sash: Nominal 0.1 inch (2.5mm) thickness polyvinyl chloride (PVC). Frame corners mechanically fastened, jamb depth is 4-9/16” and fin is integral to master frame. Sash corners are miter cut and fusion welded.
	** NOTE TO SPECIFIER ** Frame color options – Delete two of the next three paragraphs and insert custom color from manufacturer's available options where required.
			2.	Color: White.
			3.	Color: Almond.
			4.	Color: Custom Exterior Finish.
			5.	Glazing: 7/8 inch (22mm) Nominal thickness insulated glass units secured to sash frame using a dual durometer glazing bead. Complies with ASTM E 2190.
	** NOTE TO SPECIFIER ** Hardware Options - Delete one of the next two paragraphs.
			6.	Locks and Hardware:
				a.	Dual point Lock.
				b.	Multi-point locking system.
	** NOTE TO SPECIFIER ** Delete the following paragraph if corrosion resistant hardware is not required.
				c.	Corrosion resistant stainless steel rollers.
			7.	Weather stripping: In compliance with AAMA 701.2.
			8.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid Option. Delete if not required.
			9.	Grids: Colonial contour grids between glass (GBG) dividers.
			10.	Sizes: Standard and custom sizes.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.06 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 5.43 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 52.66 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: SD-R35 (DP35)- Test Size: 96 inches x 80 inches (2438mm x 2032mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete four of the following five paragraphs.
				a.	Tempered Clear / Tempered: U-Factor - 0.46 / R-Value - 2.17 / SHGC - 0.54 / VT - 0.59.
				b.	Tempered Low-E: U-Factor - 0.34 / R-Value - 2.94 / SHGC - 0.29 / VT - 0.53.
				c.	Tempered Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.25 / VT - 0.53.
				d.	Tribute DG2XLow-E/Argon SunClean: U-Factor- 0.30/ R-Value- 3.33/ SHGC - 0.25 / VT - 0.46.
				e.	Tribute HP TG 2XLow e/Krypton SunClean: U-Factor- 0.22/ R-Value 4.54 / SHGC - 0.22 / VT - 0.37.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT single hung windows are specified.
	2.21	REPLACEMENT SLIMLINE SINGLE HUNG WINDOWS
		A.	Construction:
			1.	Nominal 0.070 inch (1.8mm) frame thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Top sash fixed with a nominal 0.065 inch (1.7mm) thickness with fusion welded corners.
	** NOTE TO SPECIFIER ** Frame color options - Delete one of the next two paragraphs.
			2.	Color: White.
			3.	Color: Almond.
			4.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and dual durometer glazing bead. Complies with ASTM E 2190.
			5.	Sash Balances: Factory calibrated block and tackle, complying with AAMA-902. Balance cords shall be anchored to glass filled nylon terminal housings that lock in place once the sash is tilted in. The locking terminal and pivot bar system shall be designed to positively interlock, to provide accurate alignment of the sash and the frame during installation and operation.
			6.	Sash Locks: Knife type locks anchored into a reinforcing bar. Double locks where openings exceed 30 1/4 inches (768mm) wide.
			7.	Weather Stripping: In compliance with AAMA 701.2.
			8.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete one of the next two paragraphs or both if not required.
			9.	Grids: Colonial contour grids between glass (GBG) dividers.
			10.	Grids: Flat diamond grids between glass (GBG) dividers.
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP30 Rating is required.
		B.	Performance
			1.	Air Infiltration: Maximum 0.06cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 5.43 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 52.63 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R35 (DP35) - Test Size: 42 inches x 77 inches (10668.8mm x 1956.8mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2. 5.
			5.	Forced Entry: Type A, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 28 and 35.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.48 / R-Value - 2.08 / SHGC - 0.61 / VT - 0.64.
				b.	Low-E: U-Factor - 0.34 / R-Value - 2.94 / SHGC - / VT - 0.56.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.31 / VT - 0.56.
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP50 Rating is required.
		C.	Performance
			1.	Air Infiltration: Maximum 0.22 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 75.24 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R50 (DP50) - Test Size: 40 inches x 63 inches (1168mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2. 5.
			5.	Forced Entry: Type A, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 28 and 35.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear DSB: U-Factor - 0.49 / R-Value - 2.04/ SHGC - 0. 0.59 / VT - 0.63.
				b.	Low-E DSB: U-Factor - 0.35 / R-Value - 2.86 / SHGC - 0 0.31 / VT - 0.56.
				c.	Low-E/Argon DSB: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.30 / VT - 0.56.
	2.22	REPLACEMENT SLIMLINE DOUBLE HUNG WINDOWS
		A.	Construction:
			1.	Nominal 0.070 inch (1.8mm) frame thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Sash shall be a nominal 0.065 inch (1.7mm) thickness and fusion welded corners.
	** NOTE TO SPECIFIER ** Frame color options - Delete one of the next two paragraphs.
			2.	Color: White.
			3.	Color: Almond.
			4.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and dual durometer glazing bead. Complies with ASTM E 2190.
			5.	Sash Balances: Factory calibrated block and tackle, complying with AAMA-902. Balance cords shall be anchored to glass filled nylon terminal housings that lock in place once the sash is tilted in. The locking terminal and pivot bar system shall be designed to positively interlock, to provide accurate alignment of the sash and the frame during installation and operation.
			6.	Sash Locks: Knife type locks anchored into a reinforcing bar. Double locks where openings exceed 30 1/4 inches (768mm) wide.
			7.	Weather Stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Select Screens - Delete one of the following two paragraphs.
			8.	Screens: Extruded aluminum full screen with 18 x 16 charcoal finished fiberglass mesh.
			9.	Screens: Extruded aluminum half screen with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete one of the next two paragraphs or both if not required.
			10.	Grids: Colonial contour grids between glass (GBG) dividers.
			11.	Grids: Flat diamond grids between glass (GBG) dividers.
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP30 Rating is required.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.06 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 5.43 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 52.63 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R35 (DP35) - Test Size: 42 inches x 77 inches (1066.8mm x 1955.8mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type A, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 28 and 35.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.48 / R-Value - 2.04 / SHGC - 0.61 / VT - 0.64.
				b.	Low-E: U-Factor - 0.34 / R-Value - 2.94/ SHGC - 0.30 0.31 / VT - 0.56.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.31 / VT - 0.56.
	** NOTE TO SPECIFIER ** Retain the next paragraph If a DP50 Rating is required.
		C.	Performance:
			1.	Air Infiltration: Maximum 0.22 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 75.24 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R50 (DP50) - Test Size: 40 inches x 63 inches (1118mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type A, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 28 and 35.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear DSB: U-Factor - 0.49 / R-Value - 2.04/ SHGC - 0.61 / VT- 0.63.
				b.	Low-E: U-Factor - 0.35 / R-Value - 2.86/ SHGC - 0.31 / VT - 0.56.
				c.	Low-E/Argon DSB: U-Factor - 0.30 / R-Value - 3.33/ SHGC - 0.31 / VT - 0.56.
		D.	Performance:
			1.	Air Infiltration: Maximum 0.03 cfm/sq.ft. at 1.6psf. (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 45.11psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: C-50 (DP50) - Test Size: 40 inches x 63 inches (1168mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Thermal Transmittance: Tested in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear DSB: U-Factor - 0.49 / R-Value - 2.04 / SHGc - 0.59 / VT - 0.63.
				b.	Low-E DSB: U-Factor - 0.35 / R-Value - 3.33 / SHGc - 0.31 / VT - 0.56.
				c.	Low-E/Argon DSB: U-Factor - 0.30 / R-Value - 3.33 / SHGc - 0.30 / VT - 0.56.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT double hung windows are specified.
	2.23	REPLACEMENT COMMERCIAL SIGNATURE REPLACEMENT DOUBLE HUNG WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.080 inch (1.8mm) thickness reinforced polyvinyl chloride (PVC) frame with mechanically fastened corners. Sash shall be nominal 0.080 inch (2mm) thickness with mechanically fastened corners.
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete one of the next two paragraphs.
			2.	Color: White.
			3.	Color: Custom Exterior Finish.
			4.	Glazing: Insulated glass units secured to sash frame using a channel glazing with dual durometer glazing fins. Complies with ASTM E 2190.
			5.	Sash Balances: Factory calibrated block and tackle, complying with AAMA-902. Balance cords shall be anchored to glass filled nylon terminal housings that lock in place once the sash is tilted in. The locking terminal and pivot bar system shall be designed to positively interlock, to provide accurate alignment of the sash and the frame during installation and operation.
			6.	Sash Locks: Cam type locks anchored with screws driven through the sash rail and into an extruded aluminum reinforcing bar. Double locks where openings exceed 30 1/4 inches (768mm) wide.
			7.	Weather Stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Select Screens - Delete three of the following four paragraphs
			8.	Screens: Extruded aluminum full screen with 18 x 16 charcoal finished fiberglass mesh.
			9.	Screens: Extruded aluminum full screen with 18 x 16 charcoal finished aluminum mesh.
			10.	Screens: Extruded aluminum half screen with 18 x 16 charcoal finished fiberglass mesh.
			11.	Screens: Extruded aluminum half screen with 18 x 16 charcoal finished aluminum mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			12.	Grids: Colonial contour grids between glass (GBG) dividers.
			13.	Grids: Flat diamond grids between glass (GBG) dividers.
			14.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			15.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance
			1.	Air Infiltration: Maximum 0.09 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 6.00 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 60.0 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-C40 (DP40) -Test Size: 56 inches x 90 inches (1422mm x 2286mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type A, Grade 10 in accordance with ASTM F 588.
			6.	Thermal Transmittance: Tested in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.50 / R-Value - 2.00/ SHGC - 0.58 VT - 0.61.
				b.	Low-E: U-Factor - 0.37 / R-Value - 2.70/ SHGC - 0.29 / VT - 0.54.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.19 / VT - 0.38.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT classic double hung windows are specified.
	2.24	REPLACEMENT CLASSIC DOUBLE HUNG WINDOWS
		A.	Construction:
			1.	Nominal 0.070 inch (1.8mm) frame thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Sash shall be a nominal 0.065 inch (1.7mm) thickness with fusion welded corners.
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			2.	Color: White.
			3.	Color: Almond.
			4.	Color: Bronze.
			5.	Color: Custom Exterior Finish.
			6.	Glazing: Insulated glass units secured to sash frame using a sealant and dual durometer glazing bead. Complies with ASTM E 2190.
			7.	Sash Balances: Factory calibrated block and tackle, complying with AAMA-902. Balance cords shall be anchored to locking terminal housings when the sash is tilted in. The locking terminal and pivot bar system shall provide accurate alignment of the sash and the frame during operation.
			8.	Sash Locks: Cam type locks anchored with screws driven through the sash rail and into an extruded aluminum reinforcing bar. Double locks where openings exceed 30 1/4 inches (768mm) wide.
			9.	Weather Stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Select Screens - Delete three of the following four paragraphs
			10.	Screens: Extruded aluminum full screen with 18 x 16 charcoal finished fiberglass mesh.
			11.	Screens: Extruded aluminum full screen with 18 x 16 charcoal finished aluminum mesh.
			12.	Screens: Extruded aluminum half screen with 18 x 16 charcoal finished fiberglass mesh.
			13.	Screens: Extruded aluminum half screen with 18 x 16 charcoal finished aluminum mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			14.	Grids: Colonial contour grids between glass (GBG) dividers.
			15.	Grids: Flat diamond grids between glass (GBG) dividers.
			16.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			17.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
	** NOTE TO SPECIFIER ** Select the following paragraph if a DP35 Rating is required.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.19 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water resistance: no leakage when tested at 5.25 psf in accordance with ASTM E-547.
			3.	Uniform structural test pressure at 52.5 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R35 (DP35) - Test Size: 44 inches x 60 inches (1118mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Sound Transmission Class (STC): 28 and 35.
			6.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear / Tempered: U-Factor - 0.48 / R-Value - 2.08 / SHGC - 0.59 / VT - 0.62.
				b.	Low-E: U-Factor - 0.34 / R-Value - 2.86 / SHGC - 0.30 / VT- 0.55.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.30 / VT 0.49.
	** NOTE TO SPECIFIER ** Select the following paragraph for a DP40 Rating. Reinforcement is required.
		C.	Performance:
			1.	Air infiltration maximum 0.14 cfm/sq. ft. at 1.57 psf (25mph) in accordance with ASTM E -283.
			2.	Water Resistance: No leakage when tested at 6.00 psf in accordance with ASTM E-547.
			3.	Uniform structural test pressure at 60.0 psf positive and negative in accordance with ASTM E 330.
			4.	Structural rating H-R 40 (DP40) - Test Size: 44 inches x 60 inches (1118mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 28 and 35.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear / Tempered: U-Factor - 0.48 / R-Value - 2.08/ SHGC - 0.59 / VT - 0.62.
				b.	Low-E: U-Factor - 0.34 / R-Value - 2.86 / SHGC - 0.30 / VT - 0.55.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.30 / VT - 0.55.
	** NOTE TO SPECIFIER ** Select the following paragraph for a DP50 Rating. Reinforcement is required.
		D.	Performance:
			1.	Air infiltration maximum 0.08 cfm/sq. ft. at 1.57 psf (25mph) in accordance with ASTM E -283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E-547.
			3.	Uniform structural test pressure at 75.24 psf positive and negative in accordance with ASTM E 330.
			4.	Structural rating H-R 50 (DP50)- Test Size: 46 inches x 60 inches (1118mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 28 and 35.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear / DSB: U-Factor - 0.48 / R-Value - 2.08/ SHGC - 0.57 / VT - 0.61.
				b.	Low-E /DSB: U-Factor - 0.35 / R-Value - 2.86 / SHGC - 0.30 / VT - 0.54.
				c.	Low-E/Argon/DSB: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.30 / VT - 0.55.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT Impact Double Hung windows are specified.
	2.25	REPLACEMENT VIGILANCE IMPACT DOUBLE HUNG WINDOWS
		A.	Construction:
			1.	Nominal 0.070 inch (1.8mm) frame thickness polyvinyl chloride (PVC) with miter cut ,fusion welded corners and reinforced Operable sash shall be a nominal 0.065 inch (1.7mm) thickness with fusion welded corners and reinforced with extruded aluminum.
			2.	Glazing: 7/8 inch (22mm) insulated glass - 8.2 mm laminated glass with 0.090 PVB Interlayer on inside pane and 1/8 inch (3mm) double strength annealed glass on outer pane. System wet glazed with structural silicone. Complies with ASTM E 2190.
				a.	Low-E with Argon.
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete one of the next two paragraphs.
			3.	Color: White.
			4.	Color: Custom Exterior Finish.
			5.	Sash Balances: Factory calibrated stainless steel constant force balance system
			6.	Sash Locks: Heavy duty cam type locks anchored with screws driven through the sash rail and into an extruded aluminum reinforcing bar. Double locks where openings exceed 30 1/4 inches (768mm) wide.
			7.	Weather Stripping: In compliance with AAMA 701.2.
			8.	Screen: Extruded aluminum half screen with 18x16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			9.	Grids: Colonial contour grids between glass (GBG) dividers.
			10.	Grids: Flat diamond grids between glass (GBG) dividers.
			11.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			12.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.10cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water resistance: no leakage when tested at 9.82 psf in accordance with ASTM E-547.
			3.	Uniform structural test pressure at 105.33psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R 70 (DP70) - Test Size: 42 inches x 72 inches in accordance with AAMA/NWWDA/CSA 101/I.S.2/a440-05.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 34.
			7.	Impact Resistance: Meets requirements of ASTM E 1886 and E 1996 for small and large missile impact.
			8.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
				a.	Low-E/Argon: U-Factor - 0.29 / R-Value - 3.45/ SHGC - 0.20 / VT - 0.45.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT Tribute Double Hung windows are specified.
	2.26	REPLACEMENT TRIBUTE DOUBLE HUNG WINDOWS
		A.	Construction:
			1.	Nominal 0.070 inch (1.8mm) frame thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Contoured sash design shall be a nominal 0.070 inch (1.7mm) thickness with fusion welded corners.
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete two of the next three paragraphs.
			2.	Color: White.
			3.	Color: Custom Exterior Finish.
			4.	Color: Custom Interior Finish - Better Grain (dark oak, red cedar, pine).
			5.	Glazing: Insulated glass units are silicone glazed with an exterior glazing bead. Complies with ASTM E 2190.
			6.	Sash Balances: Factory calibrated block and tackle, complying with AAMA-902. Balance cords shall be anchored to locking terminal housings when the sash is tilted in. The locking terminal and pivot bar system shall provide accurate alignment of the sash and the frame during operation.
			7.	Two Sash Locks: unique low profile locks operate the tilt release latches allowing the sash to tilt-in.
			8.	Weather Stripping: In compliance with AAMA 701.2.
			9.	Screens: Extruded aluminum half screen with VIEWS (Virtually invisible enhanced window screen.)
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			10.	Grids: Colonial contour grids between glass (GBG) dividers.
			11.	Grids: Flat diamond grids between glass (GBG) dividers.
			12.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			13.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
	** NOTE TO SPECIFIER ** Retain the following paragraph if a DP35 Rating is required.
		B.	Performance.
			1.	Air Infiltration: Maximum 0.07 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water resistance: no leakage when tested at 5.43 psf in accordance with ASTM E-547.
			3.	Uniform structural test pressure at 52.66 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-LC35 (DP35) - Test Size: 48 inches x 84 inches (1118mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588-97.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete one of the next two paragraphs.
				a.	Low-E/Argon SunClean: U-Factor 0.30 / R-Value: 3.33/ SHGC - 0.25 / VT - 0.45
				b.	Tribute HP TG2X Low E/Krypton SunClean and Climaguard: U-Factor 0.21 / R-Value 4.54/ SHGC - 0.21 / VT - 0.36.
	** NOTE TO SPECIFIER ** Retain the following paragraph if a DP50 Rating is required.
		C.	Performance.
			1.	Air Infiltration: Maximum 0.05 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water resistance: no leakage when tested at 7.52 psf in accordance with ASTM E-547.
			3.	Uniform structural test pressure at 74.24 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: H-R50 (DP50) - Test Size: 42 inches x 77 inches (1118mm x 1524mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588-97.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete one of the next two paragraphs.
				a.	Low-E/Argon SunClean: U-Factor 0.30 / R-Value: 3.33/ SHGC - 0.25 / VT - 0.45.
				b.	Tribute HP TG2X low e/Krypton SunClean and Climaguard U -Factor 0.21 / R-Value= 4.54/ SHGC - 0.21 / VT - 0.36.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT casement windows are specified.
	2.27	REPLACEMENT CASEMENT WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			2.	Color: White.
			3.	Color: Almond.
			4.	Color: Bronze.
			5.	Color: Custom Exterior Finish.
			6.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and rigid PVC glazing bead. Complies with ASTM E 2190.
			7.	Hinges: Maxim 14 series.
			8.	Sash Locks: Sequentially locking multi-point type with single handle actuator.
			9.	Operator: Maxim 50 series.
			10.	Weather Stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Screen Options - Delete one of the next two paragraphs.
			11.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
			12.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished aluminum mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			13.	Grids: Colonial contour grids between glass (GBG) dividers.
			14.	Grids: Flat diamond grids between glass (GBG) dividers.
			15.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			16.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
	** NOTE TO SPECIFIER ** Select the following paragraph if a DP120 Rating is required.
		B.	Performance:
			1.	Air Infiltration: Maximum .01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.00 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 112.50 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: C-C120 (DP120) - Test Size: 24 inches x 48 inches (mm x mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 30 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29, 35 and 40.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.44 / R-Value - 2.27 / SHGC - 0.45 / VT - 0.47.
				b.	Low-E: U-Factor - 0.33 / R-Value - 3.03 / SHGC - 0.23 / VT - 0.42.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.23 / VT - 0.42.
	** NOTE TO SPECIFIER ** Select the following paragraph if a DP40 Rating is required.
		C.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 60.15psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: C-40 (DP40)- Test Size: 36 inches x 80 inches (914mm x 2032mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 30 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29, 35 and 40.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.44 / R-Value - 2.27 / SHGC - 0.45 / VT - 0.47.
				b.	Low-E: U-Factor - 0.33 / R-Value - 3.03 / SHGC - 0.23 / VT - 0.42.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.23 / VT - 0.42.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT impact casement windows are specified.
	2.28	REPLACEMENT VIGILANCE IMPACT CASEMENT WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Both sash and frame are reinforced with extruded aluminum.
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete one of the next two paragraphs.
			2.	Color: White.
			3.	Color: Custom Exterior Finish.
			4.	Glazing: 7/8 inch (22mm) insulated glass 8.2 laminated glass with 0.090 inch PVB interlayer on inside and 1/8 inch (3mm) double strength annealed on outside. System to be wet glazed with structural silicone. Complies with ASTM E 2190.
			5.	Hinges: Stainless Steel Maxim 14 series.
			6.	Sash Locks: Sequentially locking multi-point type with single handle actuator.
			7.	Operator: Maxim 50 series.
			8.	Weather stripping: In compliance with AAMA 701.2.
			9.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			10.	Grids: Colonial contour grids between glass (GBG) dividers.
			11.	Grids: Flat diamond grids between glass (GBG) dividers.
			12.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			13.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 97.74 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: C-65 (DP65) Test Size: 32 inches x 65 inches in accordance with /AAMA/NWWDA/CSA 101/I.S.2
			5.	Sound Transmission Class (STC): 34 and 37.
			6.	Forced Entry: Type B, Grade 30 in accordance with ASTM F 588.
			7.	Impact Resistance: Meets requirements of ASTM E 1886 and E 1996 for small and large missile impact.
			8.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
				a.	Energy Star Low-E/Argon: U-Factor - 0.29 / R-Value - 3.45 / SHGC - 0.20 / VT - 0.45.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT Tribute casement windows are specified.
	2.29	REPLACEMENT TRIBUTE CASEMENT WINDOWS
		A.	Construction.
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete two of the next three paragraphs.
			2.	Color: White.
			3.	Color: Custom Exterior Finish.
			4.	Color: Custom Interior Finish - Better Grain (dark oak, red cedar, pine).
			5.	Glazing: Insulated glass units secured to sash frame using a silicone sealant and rigid PVC glazing bead. Complies with ASTM E 2190.
			6.	Hinges: Maxim 14 series.
			7.	Sash Locks: Sequentially locking multi-point type with single handle actuator.
			8.	Operator: Maxim 50 series.
			9.	Weather Stripping: In compliance with AAMA 701.2.
			10.	Screens: Extruded aluminum frame with VIEWS (Virtually invisible enhanced window screen.)
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			11.	Grids: Colonial contour grids between glass (GBG) dividers.
			12.	Grids: Flat diamond grids between glass (GBG) dividers.
			13.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			14.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance.
			1.	Air Infiltration: Maximum 0.01cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 60.15 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: C-40 (DP-40) - Test Size: 36 inches x 80 inches (914mm x 2032mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 30 in accordance with ASTM F 588-97.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete one of the next two paragraphs.
				a.	Low-E/Argon SunClean: U-Factor 0.30 / R-Value: 3.33 / SHGC - 0.21 / VT 0.36.
				b.	HP TG 2X Low-E/ Krypton SunClean and Climaguard: U-Factor: 0.22 / R-Value: 4.55 / SHGC - 0.17 / VT - 0.29.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT awning windows are specified.
	2.30	REPLACEMENT AWNING WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			2.	Color: White.
			3.	Color: Almond.
			4.	Color: Bronze.
			5.	Color: Custom Exterior Finish.
			6.	Glazing: Insulated glass units secured to sash frame using a sealant and rigid PVC glazing bead. Complies with ASTM E 2190.
			7.	Hinges: Maxim 13 series.
			8.	Sash Locks: Maxim 24 Series single point locks.
			9.	Weather stripping: In compliance with AAMA 701.2.
			10.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			11.	Grids: Colonial contour grids between glass (GBG) dividers.
			12.	Grids: Flat diamond grids between glass (GBG) dividers.
			13.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			14.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 60.19 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: AP-LC40 (DP40)- Test Size: 60 inches x 42 inches (1524mm x 1067mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 20 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29, 35 and 40.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.44 / R-Value - 2.27/ SHGC- 0.45 / VT - 0.47.
				b.	Low-E: U-Factor - 0.33 / R-Value - 3.03/SHGC-0.23 / VT - 0.42.
				c.	Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33./SHGC- 0.23 / VT - 0.42.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT Impact Awning windows are specified.
	2.31	REPLACEMENT VIGILANCE IMPACT AWNING WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. Both sash and frame are reinforced with extruded aluminum.
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete one of the next two paragraphs.
			2.	Color: White.
			3.	Color: Custom Exterior Finish.
			4.	Glazing: 7/8 inch (22mm) insulated glass, 8.2 laminated glass with 0.090 PVB Interlayer on inside and 1/8 double strength annealed glass on outside . System shall be wet glazed with structural silicone. Complies with ASTM E 2190.
			5.	Hinges: Stainless Steel Maxim 13 series.
			6.	Sash Locks: Maxim 24 Series single point locks.
			7.	Weather stripping: In compliance with AAMA 701.2.
			8.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			9.	Grids: Colonial contour grids between glass (GBG) dividers.
			10.	Grids: Flat diamond grids between glass (GBG) dividers.
			11.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			12.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 112.78 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: AP-LC75 (DP75) - Test Size: 48 inches x 32 inches in accordance with AAMA/NWWDA/CSA 101/I.S.2 /A440-05.
			5.	Forced Entry: Type B, Grade 20 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 34 and 37.
			7.	Impact Resistance: Meets requirements of ASTM E 1886 and E 1996 for small and large missile impact.
			8.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
				a.	Low-E/Argon: U-Factor 0.30 / R-Value - 3.33/ SHGC - 0.26 / VT - 0.47.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT Tribute awning windows are specified.
	2.32	REPLACEMENT TRIBUTE AWNING WINDOWS
		A.	Construction.
			1.	Frame and Sash: Nominal 0.080 inch (2mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete two of the next three paragraphs.
			2.	Color: White.
			3.	Color: Custom Exterior Finish.
			4.	Color: Custom Interior Finish - Better Grain (dark oak, red cedar, pine).
			5.	Glazing: 7/8 inch (22mm) nominal thickness insulated glass units secured to sash frame using a silicone sealant and rigid PVC glazing bead. Complies with ASTM E 2190.
			6.	Hinges: Maxim 13 series.
			7.	Sash Locks: Maxim 24 Series single point locks.
			8.	Weather stripping: In compliance with AAMA 701.2.
			9.	Screens: Extruded aluminum frame with VIEWS (Virtually invisible enhanced window screen.)
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			10.	Grids: Colonial contour grids between glass (GBG) dividers.
			11.	Grids: Flat diamond grids between glass (GBG) dividers.
			12.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			13.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance.
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 1 12.12 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 60.19 psf positive and negative in accordance with ASTM E 330.
			4.	Sound Transmission Class (STC): 29, 35 and 40.
			5.	Structural Rating: AP-LC40 (DP 40) - Test Size: 60 inches x 42 inches (1524mm x 1067mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			6.	Forced Entry: Type B, Grade 20 in accordance with ASTM F 588-97.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete one of the next two paragraphs.
				a.	Low-E/Argon SunClean: U-Factor 0.30 / R-Value - 3.33 / SHGC - 0.21 / VT - 0.36.
				b.	HP TG 2 X Low-E/Krypton SunClean and Climaguard: U-Factor 0.22 / R-Value - 4.55/ SHGC - 0.17 / VT - 0.29.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT hopper windows are specified.
	2.33	REPLACEMENT HOPPER WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.065 inch (1.7mm) thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
			2.	Sash: Nominal 0.065 inch (1.7 mm) miter cut and mechanically fastened corners.
	** NOTE TO SPECIFIER ** Frame color options – Delete two of the next three paragraphs and insert custom color from manufacturer's available options where required.
			3.	Color: White.
			4.	Color: Almond.
			5.	Color: Custom Exterior Finish.
			6.	Glazing: Insulated glass to be glazed utilizing a two leaf dual durometer glazing channel. Complies with ASTM E 2190.
			7.	Hinges: Maxim 13 series.
			8.	Sash Locks: Knife type double locks where openings exceed 30 1/4 inches (768mm) wide.
			9.	Weather stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Screen Options - Delete one of the next two paragraphs.
			10.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished fiberglass mesh.
			11.	Screens: Extruded aluminum frame with 18 x 16 charcoal finished aluminum mesh.
	** NOTE TO SPECIFIER ** Grid options - Delete one of the next two paragraphs or both if not required.
			12.	Grids: Colonial contour grids between glass (GBG) dividers.
			13.	Grids: Flat diamond grids between glass (GBG) dividers.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.06 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 2.93 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 22.57 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: AP-R15 - Test Size: 48 inches x 32 inches (1219mm x 813mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2/A440-05.
			5.	Forced Entry: Type B, Grade 10 in accordance with ASTM F 588.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.46 / R-Value - 2.17 / SHGC - 0.55 / VT - 0.57.
				b.	Low-E: U-Factor - 0.34 / R-Value - 2.94/ SHGC - 0.28 / VT - 0.50.
				c.	2X Low-E/Argon: U-Factor - 0.30 / R-Value - 3.33 / SHGC - 0.26 / VT - 0.44.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT rolling windows are specified.
	2.34	REPLACEMENT ROLLING WINDOWS
		A.	Construction:
			1.	Frame and Sash: Nominal 0.1 inch (2.5mm) thickness polyvinyl chloride (PVC). Sill and Jamb corners are miter cut and fusion welded. Head and jamb corners are miter cut and mechanically fastened. Sash shall be a nominal 0.078 inch (2.0mm) thickness with miter cut and mechanically fastened corners.
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			2.	Color: White.
			3.	Color: Almond.
			4.	Color: Bronze.
			5.	Color: Custom Exterior Finish.
			6.	Glazing: Insulated glass units secured to sash frame using sealant and a dual durometer U-channel glazed. Complies with ASTM E 2190.
			7.	Sash Locks: Cam type locks into a reinforcement bar and double locks where openings exceed 36 3/8 inches (924mm) in height.
			8.	Weather stripping: In compliance with AAMA 701.2.
	** NOTE TO SPECIFIER ** Select Screens - Delete one of the following two paragraphs
			9.	Screens: Extruded aluminum screen with 18 x 16 charcoal finished fiberglass mesh.
			10.	Screens: Extruded aluminum screen with 18 x 16 charcoal finished aluminum mesh.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			11.	Grids: Colonial contour grids between glass (GBG) dividers.
			12.	Grids: Flat diamond grids between glass (GBG) dividers.
			13.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			14.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
	** NOTE TO SPECIFIER ** Select the following paragraph if a DP35 Rating is required.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.08 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 6.0 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 52.50 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: HS-LC35 (DP35) - Test Size: 78 inches x 64 inches (1981mm x 1626mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type A, Grade 20 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC): 29.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.49 / R-Value - 2.04 / SHGC - 0.62 / VT - 0.64.
				b.	Low-E: U-Factor - 0.36 / R-Value - 2.78 / SHGC - 0.32 / VT - 0.57.
				c.	TG - 2XLow-E/Argon: U-Factor - 0.27 / R-Value - 3.70 / SHGC - 0.27 / VT - 0.46.
	** NOTE TO SPECIFIER ** Select the following paragraph if a DP40 Rating is required.
		C.	Performance:
			1.	Air Infiltration: Maximum 0.08 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 6.0 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 75.0 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: HS-LC40 (DP40) - Test Size: 69 inches x 54 inches (1753mm x 1372mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type D, Grade 20 in accordance with ASTM F 588.
			6.	Sound Transmission Class (STC):29.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.49 / R-Value - 2.04 / SHGC - 0.62 / VT - 0.57.
				b.	Low-E: U-Factor - 0.36 / R-Value - 2.78/ SHGC - 0.32 / VT - 0.57.
				c.	TG- 2X Low-E/Argon: U-Factor - 0.27 / R-Value - 3.70 / SHGC - 0.27 / VT - 0.46.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT Tribute rolling windows are specified.
	2.35	REPLACEMENT TRIBUTE ROLLING WINDOWS
		A.	Construction.
			1.	Frame and Sash: Nominal 0.1 inch (2.5mm) thickness polyvinyl chloride (PVC). Sill and Jamb corners are miter cut and fusion welded. Head and jamb corners are miter cut and mechanically fastened. Sash shall be a nominal 0.078 inch (2.0mm) thickness with miter cut and mechanically fastened corners.
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete two of the next three paragraphs.
			2.	Color: White.
			3.	Color: Custom Exterior Finish.
			4.	Color: Custom Interior Finish. Better Grain (red cedar, pine and oak).
			5.	Glazing: Insulated glass units secured to sash frame using channel glazing with dual durometer glazing fins. Complies with ASTM E 2190.
			6.	Sash Locks: Cam type locks into a reinforcement bar and double locks where openings exceed 36 3/8 inches (924mm) in height.
			7.	Weather stripping: In compliance with AAMA 701.2.
			8.	Screens: Extruded aluminum screen VIEWS (Virtually invisible enhanced window screen.)
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			9.	Grids: Colonial contour grids between glass (GBG) dividers.
			10.	Grids: Flat diamond grids between glass (GBG) dividers.
			11.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			12.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
	** NOTE TO SPECIFIER ** Select the following paragraph if a DP35 Rating is required.
		B.	Performance.
			1.	Air Infiltration: Maximum 0.08 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 6.0 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 52.5 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: HS-LC35 (DP 35) - Test Size: 78 inches x 64 inches (1981mm x 1626mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type D, Grade 20 in accordance with ASTM F 588-97.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete one of the next two paragraphs.
				a.	HP TG - 2xLow E /Argon SunClean: U-Factor - 0.27/ R-Value - 3.70/ SHGC - 0.27 / VT - 0.46.
				b.	HP TG 2X Low E/Krypton SunClean and Climaguard: U-Factor - 0.22 / R-Value - 4.55/ SHGC - 0.23 / VT - 0.39.
	** NOTE TO SPECIFIER ** Select the following paragraph if a DP40 Rating is required.
		C.	Performance.
			1.	Air Infiltration: Maximum 0.08 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 6.0 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 75.00 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: HS-LC40 (DP 40) - Test Size: 69 inches x 54 inches (1752mm x 1371mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type D, Grade 20 in accordance with ASTM F 588-97.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete one of the next two paragraphs.
				a.	HP TG - 2xLow E /Argon SunClean: U-Factor - 0.27 / R-Value - 3.70/ SHGC - 0.27 / VT - 0.46.
				b.	HP TG 2x Low E/Krypton SunClean and Climaguard: U-Factor - 0.22 / R-Value - 4.55/ SHGC - 0.23 / VT - 0.39.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT picture windows are specified.
	2.36	REPLACEMENT PICTURE WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.075 inch (1.9mm) wall thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			2.	Color: White.
			3.	Color: Almond.
			4.	Color: Bronze.
			5.	Color: Custom Exterior Finish.
			6.	Glazing: Insulated glass units secured to sash frame using sealant and a dual durometer glazing bead. Complies with ASTM E 2190.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			7.	Grids: Colonial contour grids between glass (GBG) dividers.
			8.	Grids: Flat diamond grids between glass (GBG) dividers.
			9.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			10.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 7.50 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 7.52 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: F-C50 (DP50) - Test Size: 70 inches x 70 inches (1778mm x 1778mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Sound Transmission Class (STC):29.
			6.	Forced Entry: Type D, Grade 40 in accordance with ASTM F 588.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear / Tempered: U-Factor - 0.49 / R-Value - 2.04 / SHGC - 0.63 / VT - 0.66.
				b.	Low-E: U-Factor - 0.35 / R-Value - 2.86 / SHGC - 0.31.
				c.	Low-E/Argon: U-Factor - 0.27 / R-Value - 3.57 / SHGC - 0.31 / VT - 0.58.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT impact picture windows are specified.
	2.37	REPLACEMENT VIGILANCE IMPACT PICTURE WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.075 inch (1.9mm) wall thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners. All frame members shall be reinforced with aluminum
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete one of the next two paragraphs.
			2.	Color: White.
			3.	Color: Custom Exterior Finish.
			4.	Glazing shall be 7/8 inch (22mm) insulating glass, 8.2mm laminated with 0.090 inch PVB Interlayer on outer layer and 1/8 inch (3mm) double strength annealed glass on inside layer. System is wet glazed with structural silicone.
				a.	Low-E with Argon.
	** NOTE TO SPECIFIER ** Grid options - Delete three of the next four paragraphs or all if not required.
			5.	Grids: Colonial contour grids between glass (GBG) dividers.
			6.	Grids: Flat diamond grids between glass (GBG) dividers.
			7.	Grids: SDL (Simulated Divided Lites).
			8.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 75.19 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: F-C50 (DP50) - Test Size: 64 inches x 65 inches in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type D, Grade 40 in accordance with ASTM F 588.
			6.	Impact Resistance: Meets requirements of ASTM E 1886 and E 1996 for small and large missile impact.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
				a.	Low-E/Argon: U-Factor - 0.27 / R-Value - 3.7 / SHGC - 0.29 / VT - 0.50.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT Tribute picture windows are specified.
	2.38	REPLACEMENT TRIBUTE PICTURE WINDOWS
		A.	Construction.
			1.	Frame: Nominal 0.070 inch (1.8mm) wall thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** White is standard. Custom Colors are available. Insert custom color from manufacturer's available options. Delete two of the next three paragraphs.
			2.	Color: White.
			3.	Color: Custom Exterior Finish.
			4.	Color: Custom Interior Finish - Better Grain (red cedar, dark oak and pine).
			5.	Glazing: Insulated glass units secured to sash frame using sealant and a dual durometer glazing bead. Complies with ASTM E 2190.
	** NOTE TO SPECIFIER ** Grid options – Delete three of the next four paragraphs or all if not required.
			6.	Grids: Colonial contour grids between glass (GBG) dividers.
			7.	Grids: Flat diamond grids between glass (GBG) dividers.
			8.	Grids: 5/8 inch (16mm) SDL (Simulated Divided Lites).
			9.	Grids: 1 inch (25mm) SDL (Simulated Divided Lites).
		B.	Performance.
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 7.52 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 75.19 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: F-C50 (DP 50) - Test Size: 70 inches x 70 inches (1778mm x 1778mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Sound Transmission Class (STC): 29.
			6.	Forced Entry: Type D, Grade 40 in accordance with ASTM F 588-97.
			7.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified – Delete one of the next two paragraphs.
				a.	Low-E/Argon SunClean: U-Factor - 0.26 / R-Value: 3.85 / SHGC - 0.25 / VT - 0.44.
				b.	HP TG 2X low E /Krypton SunClean and Climaguard: U- Factor - 0.16 / R-Value - 6.25 / SHGC - 0.23 / VT - 0.40.
	** NOTE TO SPECIFIER ** Delete the following article if no REPLACEMENT Designer Shapes windows are specified.
	2.39	REPLACEMENT DESIGNER SHAPES WINDOWS
		A.	Construction:
			1.	Frame: Nominal 0.1 inch (2.5mm) wall thickness polyvinyl chloride (PVC) with miter cut and fusion welded corners.
	** NOTE TO SPECIFIER ** Frame color options – Delete three of the next four paragraphs and insert custom color from manufacturer's available options where required.
			2.	Color: White.
			3.	Color: Almond.
			4.	Color: Bronze.
			5.	Color: Custom Exterior Finish.
			6.	Glazing: Insulated glass units secured to sash frame using silicone removable glazing bead. Complies with ASTM E 2190.
	** NOTE TO SPECIFIER ** Grid option – Delete the next paragraph if not required.
			7.	Grids: Colonial contour grids between glass (GBG) dividers.
		B.	Performance:
			1.	Air Infiltration: Maximum 0.01 cfm/sq. ft. at 1.57 psf (25 mph) in accordance with ASTM E 283.
			2.	Water Resistance: No leakage when tested at 4.5 psf in accordance with ASTM E 547.
			3.	Uniform structural test pressure at 45.0 psf positive and negative in accordance with ASTM E 330.
			4.	Structural Rating: F-C30 (DP30) - Test Size: 64 inches x 64 inches (1626mm x 1626mm) in accordance with ANSI/AAMA/NWWDA 101/I.S.2.
			5.	Forced Entry: Type B, Grade 40 in accordance with ASTM F 588.
			6.	Thermal Transmittance: The following values are in accordance with NFRC 100 and NFRC 200.
	** NOTE TO SPECIFIER ** Select glazing type specified - Delete two of the next three paragraphs.
				a.	Clear: U-Factor - 0.47 / R-Value - 2.13/ SHGC - 0.66 / VT - 0.71.
				b.	Low-E: U-Factor - 0.32 / R-Value - 3.13/ SHGC - 0.34 / VT - 0.63.
				c.	Low-E/Argon:U-Factor0.28/R-Value-3.57SHGc- 0.34/ VT 0.63.
	2.40	REPLACEMENT WINDOW ACCESSORIES
	** NOTE TO SPECIFIER ** Mullion options – Delete entire paragraph if mullions are not required.
		A.	Mullions:
	** NOTE TO SPECIFIER ** Common mulled units are available up to 130 inches wide. Delete two of the next three paragraphs.
			1.	Common Jamb: Windows are contained within single frame and separated by a common mull post.
			2.	Structural Mullion: DP 50 rated mullion for areas requiring conformance to increased wind loads.
			3.	Non-Structural Combination Mullion: Horizontal or vertical members formed by joining two or more window units. May be factory or field applied.
	PART 3	EXECUTION
	3.1	EXAMINATION
		A.	Verify rough opening size is of sufficient size to receive window unit and complies with manufacturer's requirements for opening clearances.
		B.	Verify that sill plate is level.
		C.	Notify Architect of unacceptable conditions before proceeding with installation.
	3.2	INSTALLATION
		A.	Install window unit in accordance with manufacturer's printed instructions.
		B.	Apply sealant around perimeter of window unit between nail fin and exterior sheathing of wall. Refer to Division 7 Section "Joint Sealants".
		C.	Install window unit level and plumb. Center window unit in opening and secure window unit by nailing through nail fin and screw through jambs as indicated in manufacturer's instructions.
		D.	Flash window in accordance with AAMA's "Standard Practice for Installation of Windows with a Mounting Flange in Stud Frame Construction".
		E.	Insulate between window frame and rough opening with insulation. Refer to Division 7 Section "Building Insulation".
	3.3	ADJUSTING
		A.	Adjust units for smooth operation without binding or racking.
		B.	Adjust sash locks and screens for smooth operation.
	3.4	CLEANING
		A.	Clean soiled surfaces and glass prior to substantial completion.
	3.5	PROTECTION
		A.	Protect window unit from damage until substantial completion. Repair or replace damaged units.
	END OF SECTION