MasterFormat: 95

Download this Specification for   WORD | WP | RTF | TEXT

Find over 500 more construction specifications | Arcat.com

	SECTION 08571
	COMPOSITE WOOD WINDOWS
	(Andersen® A-Series)
	Copyright 2014 ARCAT, Inc. - All rights reserved
	** NOTE TO SPECIFIER ** Andersen Windows, Inc.; windows and doors. . This section is based on the products of Andersen Windows, Inc., which is located at: 100 Fourth Ave. N. P. O. Box 12 Bayport, MN 55003-1096 Toll Free Tel: 800-299-9029 Tel: 651-264-5150 Fax: 752-752-9230 Email: request info Web: www.andersenwindows.com [ Click Here ] for additional information. The privately owned business was founded in 1903 by Danish immigrant Hans Andersen and his family in Hudson, Wisconsin, where logs arrived via the St. Croix River. Today, Andersen Corporation is an international enterprise employing over 9,000 people at more than 20 locations with headquarters in Bayport, Minnesota, a 2.8 million-square-foot facility that covers 65 acres. Andersen annually manufactures more than six million wood windows and doors, with sales worldwide.
	PART 1	GENERAL
	1.1	SECTION INCLUDES
	** NOTE TO SPECIFIER ** Delete items below not required for project.
		A.	Composite clad wood windows of the following types (Andersen A-Series):
			1.	Double-hung windows.
			2.	Casement windows.
			3.	Awning windows.
			4.	Picture windows.
			5.	Transom fixed windows.
			6.	Transom venting windows.
		B.	Gliding patio doors of the following types (Andersen A-Series):
			1.	Gliding patio doors.
		C.	Hinged patio doors of the following types (Andersen A-Series):
			1.	Hinged patio doors.
			2.	Outswing patio doors.
			3.	Patio door sidelights.
			4.	Patio door transoms.
	1.2	RELATED SECTIONS
	** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
		A.	Section 03300 - Cast-In-Place Concrete: Openings in cast-in-place concrete.
		B.	Section 03450 - Precast Concrete Wall Panels: Openings in precast concrete wall panels.
		C.	Section 04810 - Unit Masonry Assemblies: Openings in masonry.
		D.	Section 05400 - Cold Formed Metal Framing: Framed Openings.
		E.	Section 06100 - Rough Carpentry: Framed openings.
		F.	Section 06200 - Finish Carpentry: Interior wood casing.
		G.	Section 07210 - Building Insulation: Batt insulation at window perimeter.
		H.	Section 07460 - Siding and trim.
		I.	Section 07620 - Flashing and Sheet Metal: Flashing associated with windows and doors.
		J.	Section 07900 - Joint Sealers: Perimeter joint sealant and backer rod.
	1.3	REFERENCES
	** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
		A.	AAMA 511 - Voluntary Guideline for Forensic Water Penetration Testing of Fenestration Products.
		B.	AAMA 502 - Voluntary Specification for Field Testing of Windows and Sliding Glass Doors.
		C.	AAMA/WDMA/CSA 101/I.S.2/A440 NAFS - North American Fenestration Standard/Specification for windows, doors, and skylights.
		D.	ASTM International (ASTM):
			1.	ASTM C 1036 - Standard Specification for Flat Glass.
			2.	ASTM C 1048 - Standard Specification for Heat-Treated Flat Glass--Kind HS, Kind FT Coated and Uncoated Glass.
			3.	ASTM E 90 - Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements.
			4.	ASTM E 330 - Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference.
			5.	ASTM E 2190 - Standard Specification for Insulating Glass Unit Performance and Evaluation
		E.	American Society of Civil Engineers (ASCE) 7 - Minimum Design Loads for Buildings and Other Structures.
		F.	International Standards Organization (ISO) 14021 - Environmental Labels and Declarations -- Self-Declared Environmental Claims (Type II environmental labeling).
		G.	National Fenestration Rating Council (NFRC) 100 - Procedure for Determining Fenestration Product U-factors.
		H.	National Fenestration Rating Council (NFRC) 200 - Procedure for Determining Fenestration Product Solar Heat Gain Coefficient and Visible Transmittance at Normal Incidence.
		I.	WDMA I.S.4 - Water-Repellent Preservative Treatment for Millwork.
	1.4	SYSTEM DESCRIPTION
	** NOTE TO SPECIFIER ** Refer to website for most current product performance data. Retain, edit, or delete language below to suit project requirements. Refer to www.andersenwindows.com for performance information.
		A.	Performance Requirements: Provide products/systems that have been manufactured, fabricated, and installed to the following performance criteria:
			1.	Comply with AAMA/WDMA/CSA 101/I.S.2/A440.
	** NOTE TO SPECIFIER ** Specify performance grade.
			2.	Performance Grade:
	** NOTE TO SPECIFIER ** Specify U-Factor.
			3.	U-Factor (NFRC 100):
	** NOTE TO SPECIFIER ** Specify SHGC.
			4.	Solar Heat Gain Coefficient (SHGC) (NFRC 200):
	** NOTE TO SPECIFIER ** Specify OITC.
			5.	Outdoor-Indoor Transmission Class (OITC) (ASTM E90):
	** NOTE TO SPECIFIER ** Specify STC.
			6.	Sound Transmission Class (STC) (ASTM E90):
	** NOTE TO SPECIFIER ** Manufacturer recommends referring to website design pressure estimator for additional wind load information. Retain, edit, or delete language below to suit project requirements.
		B.	Structural Requirements: Provide products/systems capable of withstanding wind loads based on testing units representative of those indicated for Project that pass AAMA/WDMA/CSA 101/I.S.2/A440, Uniform Structural Load Test:
			1.	Design Wind Loads: Determine design wind loads applicable to Product from basic wind speed indicted in miles per hour (meters per second) at 33 feet (10 meters) above grade, according to ASCE-7, Section 6, based upon mean roof heights indicted on Drawings.
	** NOTE TO SPECIFIER ** Specify wind speed.
				a.	Basic Wind Speed:
	** NOTE TO SPECIFIER ** Specify importance factor.
				b.	Importance Factor:
	** NOTE TO SPECIFIER ** Specify exposure category.
				c.	Exposure Category:
	** NOTE TO SPECIFIER ** Specify design pressure requirement.
				d.	Wind Load Requirement:
	1.5	SUBMITTALS
		A.	Submit under provisions of Section 01300.
		B.	Product Data: Manufacturer's data sheets on each product to be used, including:
			1.	Preparation instructions and recommendations.
			2.	Storage and handling requirements and recommendations.
			3.	Installation methods.
		C.	Shop Drawings: Provide drawings indicating direction of operable parts, typical jamb, head and sill conditions, and special mullion reinforcement details.
		D.	Quality Assurance/Control Submittals:
			1.	Performance Data: Manufacturer's published performance data for specified products.
	** NOTE TO SPECIFIER ** Delete if not required.
		E.	Sustainable Building Submittals:
	** NOTE TO SPECIFIER ** Retain subparagraph below and energy performance certification paragraph in quality assurance article if wood windows are required to be certified. Delete if not required.
			1.	Energy Performance:
				a.	Provide NFRC 100 and NFRC 200 Certified performance values meeting or exceeding values specified in Performance Criteria Article.
	** NOTE TO SPECIFIER ** Retain subparagraph below and recycled content certification in quality assurance article. Delete if not required.
			2.	Recycled Content.
				a.	Provide values in percent by weight of recycled content per ISO 14021 Standard for each product specified.
				b.	Provide statement indicating total content value for each product containing recycled content and fraction by weight that is considered recycled content.
	** NOTE TO SPECIFIER ** Retain subparagraph below if wood windows are required to be qualified for regional materials. Delete if not required.
			3.	Regional Materials.
				a.	Provide window manufacturer's Product Data for regional materials within 500 miles of project location, indicating location and distance from Project of material manufacturer and point of extraction, harvest, or recovery and manufacture for each qualifying window component.
				b.	Provide statement indicating content value for each product containing regional material and the fraction by weight that is considered regional material.
			4.	FSC Wood-based Materials.
				a.	Provide third party certification that wood-based window materials retain FSC Chain-of-Custody certification.
				b.	Provide statement indicating total content value for each product containing FSC wood-based content and fraction by weight that is considered FSC wood-based content.
	** NOTE TO SPECIFIER ** Retain paragraph below if windows are required to be certified for indoor air quality Delete if not required.
			5.	Indoor Environmental Quality.
				a.	Provide third party certification that window materials, including factory applied finishes, meet indoor air quality standards for low emitting materials under California CA Section 01350 Specifications.
	** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.
		F.	Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.
			1.	Hardware: Submit samples indicating typical finish on window hardware.
			2.	Cladding: Submit color samples of vinyl cladding.
			3.	Interior Finishes: Submit color samples of interior finishes.
		G.	Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.
			1.	Hardware: Submit samples indicating typical finish on window hardware.
			2.	Cladding: Submit color samples of vinyl cladding.
			3.	Interior Finishes: Submit color samples of interior finishes.
		H.	Manufacturer's Warranty: Submit, for Owner's acceptance, manufacturer's standard limited warranty document.
		I.	Owner's Manual: Bound manual clearly identified with project name, location, and completion date. Identify type and size of units installed. Provide recommendations for periodic inspections, care, and maintenance. Identify common causes of damage with instructions for temporary repair.
	1.6	QUALITY ASSURANCE
		A.	Manufacturer Qualifications: A manufacturer capable of fabricating wood windows that meet or exceed Performance Criteria indicated and of documenting this performance by inclusion in lists and by labels, test reports, and calculations.
	** NOTE TO SPECIFIER ** Delete FSC certification for manufacturer and vendor if not required..
			1.	A manufacturer who is certified for chain-of-custody by an FSC accredited certification body.
			2.	Vendor Qualifications: A vendor that is certified for chain of custody by an FSC accredited certification body.
		B.	Installer Qualifications: Utilize an installer having demonstrated experience on projects of similar size and complexity.
	** NOTE TO SPECIFIER ** Specify applicable requirements of regulatory agencies.
		C.	Regulatory Requirements and Approvals:
		D.	Certifications:
			1.	National Fenestration Rating Council (NFRC). Products shall be certified and labeled for U-Factor, Solar Heat Gain Coefficient (SHGC), and Visible Transmittance per NFRC 100 and 200 Procedures. Unique glass types that are special ordered may not apply, check with Manufacturer.
			2.	Window and Door Manufacturers Association (WDMA). Products shall be certified and labeled per WDMA Hallmark Certification Program to the AAMA/WDMA/CSA 101/I.S.2/A440 industry standard.
	** NOTE TO SPECIFIER ** Delete certification label not required.
			3.	Insulating Glass Units: Provide insulating glass units permanently marked with certification label of Insulating Glass Certification Council (IGCC) indicating compliance with ASTM E2190.
			4.	Insulating Glass Units: Provide insulating glass units permanently marked with certification label of Insulating Glass Manufacturers Association of Canada (IGMAC) indicating compliance with CAN/CGSB or ASTM E2190.
	** NOTE TO SPECIFIER ** Retain paragraph below if pre-installation meeting is required. Specify requirements for pre-installation meeting.
		E.	Pre-Installation Meetings: Conduct meeting at Project site to comply with requirements in Division 01 Section - Project Management and Coordination.
	** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.
		F.	Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.
			1.	Finish areas designated by Architect.
			2.	Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.
			3.	Refinish mock-up area as required to produce acceptable work.
	1.7	DELIVERY, STORAGE, AND HANDLING
		A.	Comply with manufacturer's ordering instructions and lead time requirements to avoid construction delays.
		B.	Delivery: Deliver materials in manufacturer's original unopened, undamaged containers with identification labels intact.
		C.	Storage and Protection: Store materials protected from exposure to harmful environmental conditions and at temperature and humidity conditions recommended by the manufacturer.
		D.	Store materials and accessories off ground, under cover, and protected from weather and construction activities.
		E.	Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.
	1.8	PROJECT CONDITIONS
		A.	Field Measurements: Verify actual dimensions of openings by field measurements before fabrication. Record measurements on shop drawings. Coordinate field measurements and fabrication schedule with construction progress to avoid construction delays.
		B.	Install units in accordance with manufacturer's safety and weather requirements.
			1.	Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.
	1.9	WARRANTY
	** NOTE TO SPECIFIER ** Andersen window & doors are covered by our exclusive Owner-to-Owner limited warranty. Most other window warranties end when a home is sold, but our coverage is completely transferable from each owner to the next. And, because it is not prorated, the coverage offers full benefits, year after year, owner after owner, so it can add real value when you decide to sell your home. Plus, we have one of the largest service networks in the industry, so help is always there if you need it.
		A.	Project Warranty: Refer to Conditions of the Contract for project Warranty provisions.
	** NOTE TO SPECIFIER ** Coordinate article below with manufacturer's warranty requirements. Visit the Andersen website for a complete description of the standard limited warranty including exclusions and limitations.
		B.	Manufacturer's Warranty: Manufacturer's standard limited warranty.
			1.	Non-prorated. Transferable from owner to the next.
			2.	Term: 20 years on glass.
			3.	Term: 10 years on non-glass parts.
		C.	Andersen A Series window units are warranted to be free from defects in manufacturing, materials and workmanship for ten years from the date of purchase.
		D.	The glass is warranted not to develop, under normal conditions, any material obstruction of vision resulting from manufacturing defects or as a result of premature failure of the glass or organic seal for ten years from the date of purchase.
	PART 2	PRODUCTS
	2.1	MANUFACTURERS
		A.	Acceptable Manufacturer: Andersen Windows, Inc., which is located at: 100 Fourth Ave. N. P. O. Box 12 ; Bayport, MN 55003-1096; Toll Free Tel: 800-299-9029; Tel: 651-264-5150; Fax: 752-752-9230; Email: request info; Web: www.andersenwindows.com
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
		B.	Substitutions: Not permitted.
		C.	Requests for substitutions will be considered in accordance with provisions of Section 01600.
	** NOTE TO SPECIFIER ** When designing window sizes, consult with Andersen window's A-series window product guide document available at www.andersenwindows.com for full description of clear opening dimensions and positions. Delete if not required.
	2.2	WINDOWS
	** NOTE TO SPECIFIER ** Delete window products not required for project. Delete if not required.
		A.	Double-Hung Windows:
			1.	Product: Andersen A-Series Full Frame Double-Hung Windows.
	** NOTE TO SPECIFIER ** Andersen casement windows have a hinge at the side and crank open outward. Delete if not required.
		B.	Casement Windows:
			1.	Product: Andersen A-Series Casement Windows.
	** NOTE TO SPECIFIER ** Andersen awning windows have a hinge at the top and open outward. Delete if not required.
		C.	Awning Windows:
			1.	Product: Andersen A-Series Awning Windows.
	** NOTE TO SPECIFIER ** Andersen picture windows are stationary windows designed to match double-hung, gliding or casement windows. Picture windows have no moving hardware and offer a wider, brighter view of the outdoors. Delete if not required.
		D.	Picture Windows:
			1.	Product: Andersen A-Series Picture Windows.
	** NOTE TO SPECIFIER ** Andersen transom windows are stationary windows designed to match double-hung, gliding or casement windows. Transom windows are often found over entry doors or other windows. Delete if not required.
		E.	Transom Fixed Windows:
			1.	Product: Andersen A-Series Transom Fixed Windows.
	** NOTE TO SPECIFIER ** Andersen transom windows are windows designed to match double-hung, gliding or casement windows. Transom windows are often found over entry doors or other windows. Venting transoms are an option. Delete if not required.
		F.	Transom Venting Windows
			1.	Product: Andersen A-Series Transom Venting Windows.
		G.	Materials:
	** NOTE TO SPECIFIER ** Required to be certified for LEED or project is being designed with sustainable practices. Delete if not required.
			1.	Certified Wood: Windows shall be certified as "FSC Mixed Credit" per FSC STD-01-001, "FSC Principles and Criteria for Forest Stewardship," and FSC STD-40-004, "FSC Standard for Chain of Custody Certification."
			2.	Frame: Fabricated from a wood species approved in WDMA I.S.4.
			3.	Exterior Frame Members:
				a.	Material: Fibrex material outer frame with wood core. Provide units in the following color:
	** NOTE TO SPECIFIER ** Delete color not required.
					1)	Color: White.
					2)	Color: Sandtone.
					3)	Color: Terratone.
					4)	Color: Forest Green.
					5)	Color: Canvas.
					6)	Color: Dove Gray.
					7)	Color: Prairie Grass.
					8)	Color: Red Rock.
					9)	Color: Cocoa Bean.
					10)	Color: Dark Bronze.
					11)	Color: Black.
	** NOTE TO SPECIFIER ** Windows can be ordered with a sash color different from the frame color.
			4.	Operable Sash Members:
				a.	Exterior Sash: Pultruded fiberglass material with adhesively bonded PVC corner keys.
				b.	Interior Sash: Clear or veneer wood adhesively applied to exterior sash components.
				c.	Material with the following painted color:
	** NOTE TO SPECIFIER ** Delete color not required.
					1)	Color: White.
					2)	Color: Sandtone.
					3)	Color: Terratone.
					4)	Color: Forest Green.
					5)	Color: Canvas.
					6)	Color: Dove Gray.
					7)	Color: Prairie Grass.
					8)	Color: Red Rock.
					9)	Color: Cocoa Bean.
					10)	Color: Dark Bronze.
					11)	Color: Black.
				d.	Interior Components: Water repellant wood preservative treated interior framing per WDMA I.S.4 in the following species and finish. Adhesively bond exterior and interior sash components.
	** NOTE TO SPECIFIER ** Delete wood species not required.
					1)	Species: Pine.
					2)	Species: Oak.
					3)	Species: Maple.
	** NOTE TO SPECIFIER ** Delete wood finish not required.
					4)	Finish: Unfinished.
					5)	Finish: Clear coat finish.
					6)	Finish: Stain Color - Cinnamon.
					7)	Finish: Stain Color - Espresso.
					8)	Finish: Stain Color - Honey.
					9)	Finish: Stain Color - Mocha.
					10)	Finish: Stain Color - Russet.
					11)	Finish: Painted Color (Pine) - White.
					12)	Finish: Painted Color (Pine) - Birch Bark.
					13)	Finish: Painted Color (Pine) - Prime.
	** NOTE TO SPECIFIER ** Delete if not required.
			5.	Picture and Transom Sash Members:
				a.	Exterior Components: Pultruded fiberglass material with adhesively bonded PVC corner keys. in the following color:
	** NOTE TO SPECIFIER ** Delete color not required.
					1)	Color: White.
					2)	Color: Sandtone.
					3)	Color: Terratone.
					4)	Color: Forest Green.
					5)	Color: Canvas.
					6)	Color: Dove Gray.
					7)	Color: Prairie Grass.
					8)	Color: Red Rock.
					9)	Color: Cocoa Bean.
					10)	Color: Dark Bronze.
					11)	Color: Black.
				b.	Interior Components: Water repellant wood preservative treated interior framing per WDMA I.S.4 in the following species and finish. Clip-fasten interior components to exterior components.
	** NOTE TO SPECIFIER ** Delete wood species not required.
					1)	Species: Pine.
					2)	Species: Oak.
					3)	Species: Maple.
	** NOTE TO SPECIFIER ** Delete wood finish not required.
					4)	Finish: Unfinished.
					5)	Finish: Clear coat finish.
					6)	Finish: Stain Color - Cinnamon.
					7)	Finish: Stain Color - Espresso.
					8)	Finish: Stain Color - Honey.
					9)	Finish: Stain Color - Mocha.
					10)	Finish: Stain Color - Russet.
					11)	Finish: Painted Color (Pine) - White.
					12)	Finish: Painted Color (Pine) - Birch Bark.
					13)	Finish: Painted Color (Pine) - Prime.
			6.	Sill: Fibrex material outer frame with wood core approved in AAMA/WDMA/CSA 101/I.S.2/A440.
			7.	Weatherstripping:
				a.	Upper Sash Head and Lower Sash Sill: Continuous bulb style, foam-filled vinyl.
				b.	Upper Sash Stiles: Single bulb style, vinyl-covered, foam-filled.
				c.	Lower Sash Stiles: Dual bulb style, vinyl-covered, foam-filled.
				d.	Meeting Rails: Continuous bulb style, foam-filled vinyl.
		H.	Hardware:
	** NOTE TO SPECIFIER ** Delete if not required.
			1.	Double-Hung Window Hardware:
	** NOTE TO SPECIFIER ** Delete lock not required.
				a.	Hardware Locks: Die-cast zinc sash locks in the following style and color:
					1)	Style: Traditional.
	** NOTE TO SPECIFIER ** Delete color not required.
					2)	Color: Stone.
					3)	Color: White.
					4)	Color: Black.
					5)	Color: Gold Dust.
					6)	Color: Bright Brass.
					7)	Color: Antique Brass.
					8)	Color: Polished Chrome.
					9)	Color: Brushed Chrome.
					10)	Color: Oil Rubbed Bronze.
					11)	Color: Satin Nickel.
				b.	Lock and Keeper: Die-cast zinc hardware with the following style and color:
					1)	Style: Traditional.
	** NOTE TO SPECIFIER ** Delete color not required.
					2)	Color: Stone.
					3)	Color: White.
					4)	Color: Black.
					5)	Color: Gold Dust.
					6)	Color: Bright Brass.
					7)	Color: Antique Brass.
					8)	Color: Polished Chrome.
					9)	Color: Brushed Chrome.
					10)	Color: Oil Rubbed Bronze.
					11)	Color: Satin Nickel.
					12)	Tilt mechanism integrated into lock.
	** NOTE TO SPECIFIER ** Delete lift hardware not required.
				c.	Finger Lift Hardware: Zinc cast with baked, powder coated finish on chromate protective coating in the following style and color:
					1)	Finger Lifts: Provide 2 per sash unit.
					2)	Style: Traditional.
	** NOTE TO SPECIFIER ** Delete color not required.
					3)	Color: Stone.
					4)	Color: White.
					5)	Color: Black.
					6)	Color: Gold Dust.
					7)	Color: Bright Brass.
					8)	Color: Antique Brass.
					9)	Color: Polished Chrome.
					10)	Color: Brushed Chrome.
					11)	Color: Oil Rubbed Bronze.
					12)	Color: Satin Nickel.
				d.	Hand Lift Hardware: Zinc die cast with baked powder coated finish on chromate protective coating in the following style and color:
					1)	Hand Lift: Provide 1 hand lift per sash unit.
					2)	Style: Traditional.
	** NOTE TO SPECIFIER ** Delete color not required.
					3)	Color: Stone.
					4)	Color: White.
					5)	Color: Black.
					6)	Color: Gold Dust.
					7)	Color: Bright Brass.
					8)	Color: Antique Brass.
					9)	Color: Polished Chrome.
					10)	Color: Brushed Chrome.
					11)	Color: Oil Rubbed Bronze.
					12)	Color: Satin Nickel.
				e.	Bar Lift Hardware: Zinc die cast with baked powder coated finish on chromate protective coating in the following style and color:
					1)	Bar Lift: Provide 1 hand lift per window unit.
					2)	Style: Traditional.
	** NOTE TO SPECIFIER ** Delete color not required.
					3)	Color: Stone.
					4)	Color: White.
					5)	Color: Black.
					6)	Color: Gold Dust.
					7)	Color: Bright Brass.
					8)	Color: Antique Brass.
					9)	Color: Polished Chrome.
					10)	Color: Brushed Chrome.
					11)	Color: Oil Rubbed Bronze.
					12)	Color: Satin Nickel.
				f.	Balancers: Fit top and bottom sash with concealed frame mounted balancers. Design balancers to allow easy operation of double-hung units.
	** NOTE TO SPECIFIER ** Delete if design pressure (DP) upgrade is not required.
				g.	DP Upgrade Window Hardware:
					1)	Provide 2 retractable interior wind load brackets at check rail.
					2)	Provide 2 upper check rail support brackets located on side outer frame members. Match bracket color to exterior frame color.
					3)	Provide 2 bottom rail support brackets located on the sill. Match bracket color to exterior frame color.
	** NOTE TO SPECIFIER ** Delete if not required.
			2.	Awning and Venting Transom Hardware:
	** NOTE TO SPECIFIER ** Select SS hinge for use when exposed to salt air or other severe environmental or industrial areas calling for higher levels of corrosion protection. Delete hinge not required.
				a.	Hinges: Powder coated painted hinge arms with 300 Series stainless steel slide track.
				b.	Hinges: 300 Series stainless steel hinge arms with 300 Series stainless steel slide track.
				c.	Operator: Electrostatically plated rotary-type operator attached to chrome-plated steel rod applied to bottom rail of sash. Single steel operator arm stamped with gear ring. Set arm gear assembly between nylon bushing and nylon spacer. Encase drive shaft and worm gear assembly in zinc die cast base.
	** NOTE TO SPECIFIER ** Add the following for use when exposed to salt air or other severe environmental or industrial areas calling for higher levels of corrosion protection.
					1)	Operators: 300 Series stainless steel gear arm rivet; zinc plated steel bottom plate. Other parts plated and powder coated steel or zinc.
				d.	Operator Handle and Covers:
					1)	Folding Handle Hardware: Zinc die cast folding handle and cover with powder coated painted finish.
	** NOTE TO SPECIFIER ** Delete folding handle style not required.
					2)	Style: Traditional.
					3)	Style Contemporary
	** NOTE TO SPECIFIER ** Delete color not required.
					4)	Color: Stone.
					5)	Color: White.
					6)	Color: Black.
					7)	Color: Gold Dust.
					8)	Color: Bright Brass.
					9)	Color: Antique Brass (Traditional style only).
					10)	Color: Polished Chrome (Traditional style only).
					11)	Color: Brushed Chrome (Traditional style only).
					12)	Color: Oil Rubbed Bronze.
					13)	Color: Satin Nickel.
	** NOTE TO SPECIFIER ** Omit sash locks where remote window operators are required. Omitting sash locks will decrease window performance. Level 20 forced entry resistance is not available when electric operator is specified. Delete if not required.
				e.	Sash Locks: Single actuation lock concealed by trim stops. Die cast zinc, galvanized steel link and engineered polymer components in finishes to match handle options.
	** NOTE TO SPECIFIER ** Delete if not required.
				f.	Provide remote window operator.
					1)	Remote Awning Window Operator: Provide electric window opener for remote operation of venting unit where indicated on Drawings consisting of a 16 volt power operator, power supply (converting 120 V AC to 16 V DC), pushbutton command center, rain sensor that will signal power operator to close unit, and necessary mounting hardware. Provide safety connector that will not permit operation of electric window opener unless insect screen is in place. Do not provide sash locks on windows equipped with remote awning window operator.
	** NOTE TO SPECIFIER ** Delete if not required.
			3.	Venting Casement Hardware:
	** NOTE TO SPECIFIER ** SS for use when exposed to salt air or other severe environmental or industrial areas calling for higher levels of corrosion protection. Delete hinge not required.
				a.	Hinges: Powder coated painted hinge arms with 300 Series stainless steel slide track.
				b.	Hinges: 300 Series stainless steel hinge arms with 300 Series stainless steel slide track.
				c.	Operators: Hardened steel operator arm stamped with a gear ring. Set arm gear between nylon bushing and nylon spacer. Encase drive shaft and worm gear assemblies in zinc die cast base and removable, painted, die-cast cover.
	** NOTE TO SPECIFIER ** Add the following for use when exposed to salt air or other severe environmental or industrial areas calling for higher levels of corrosion protection.
					1)	Operators: 300 Series stainless steel gear arm link and clip; 300 Series stainless steel gear arm rivet; zinc plated steel bottom plate. Other parts plated and powder coated steel or zinc.
				d.	Folding Handle: Zinc die cast handle and cover with powder coated painted finish.
	** NOTE TO SPECIFIER ** Delete folding handle style not required.
					1)	Style: Traditional.
					2)	Style Contemporary
	** NOTE TO SPECIFIER ** Delete color not required.
					3)	Color: Stone.
					4)	Color: White.
					5)	Color: Black.
					6)	Color: Gold Dust.
					7)	Color: Bright Brass.
					8)	Color: Antique Brass (Traditional style only).
					9)	Color: Polished Chrome (Traditional style only).
					10)	Color: Brushed Chrome (Traditional style only).
					11)	Color: Oil Rubbed Bronze.
					12)	Color: Satin Nickel.
				e.	Lock Handle and Bezel: Universal lock handle of die cast zinc with powder coated paint finish and polycarbonate bezel in the following color:
	** NOTE TO SPECIFIER ** Delete color not required.
					1)	Color: Stone.
					2)	Color: White.
					3)	Color: Black.
					4)	Color: Gold Dust.
					5)	Color: Bright Brass.
					6)	Color: Antique Brass.
					7)	Color: Polished Chrome.
					8)	Color: Brushed Chrome.
					9)	Color: Oil Rubbed Bronze.
					10)	Color: Satin Nickel.
				f.	Sash Locks: Single actuation lock concealed by trim stops. Die cast zinc, galvanized steel link and engineered polymer components.
		I.	Accessories
	** NOTE TO SPECIFIER ** Delete if not required.
			1.	Sill Stool: Wood members machined from clear material or veneered finger joined material approved in AAMA/WDMA/CSA 101/I.S.2/A440.
	** NOTE TO SPECIFIER ** Delete if not required.
			2.	Extension Jambs: Wood members machined from clear material or veneered finger joined material. Pre-drill extension jambs for application. Factory-applied extension jambs are available in 1/16 inch (1.6 mm)depth increments ranging from 5-1/4 inch (133 mm) depth to 7-1/8 inch (181 mm).
	** NOTE TO SPECIFIER ** Delete if not required.
			3.	Exterior Trim and Casing: Where indicated on Drawings, provide trim attached to attachment strip.
				a.	Color: Match window framing unless indicated otherwise. Refer to Exterior Finish Schedule.
	** NOTE TO SPECIFIER ** Typical trim combination styles. Delete styles not required.
				b.	Trim Style: Flat trim with extended head and extended sill.
				c.	Trim Style: Flat trim with flush head and extended sill.
				d.	Trim Style: Brick mould with extended sill.
				e.	Trim Style: Flat trim with decorative drip cap and extended sill.
				f.	Trim Style: Flat trim with 2 inches (51 mm) cornice and extended sill.
				g.	Trim Style: Flat trim with 3-5/8 inches (92 mm) cornice and extended sill.
				h.	Profiles: Fibrex material.
	** NOTE TO SPECIFIER ** Delete trim not required.
					1)	Flat Trim Width: 3-1/2 inch (89 mm) by 1 1/2 inches (38 mm) deep.
					2)	Flat Trim Width: 4 1/2 inches (114 mm) by 1 1/2 inches (38 mm) deep.
					3)	Brick Mould: 2 inch (51 mm) wide by 1 5/8 inches (41 mm) deep.
					4)	Sill Nose: 1 15/16 inches (49 mm) wide by 1 7/8 inches (48 mm) deep.
					5)	Mull Cover: 4-1/4 inch (108 mm) wide by 1 1/2 inches (38 mm) deep.
	** NOTE TO SPECIFIER ** Mull cover above is for face. Mull cover below is for pockets.
					6)	Mull Cover: 3-3/4 inch (95 mm) wide by 1 1/2 inches (38 mm) deep.
				i.	Profiles: Molded Urethane.
	** NOTE TO SPECIFIER ** Delete trim not required.
					1)	Cornice: 3 5/8 inches (92 mm) high by 4 inches (102 mm) deep.
					2)	Cornice: 2 inches (51 mm) high by 3 1/4 inches (83 mm) deep.
					3)	Decorative Drip Cap: 15/16 inches (24 mm) high by 2 1/4 inches (57 mm) deep.
	** NOTE TO SPECIFIER ** Andersen bay windows can be wall supported or suspended. The cable support system is required when units are to be suspended. Each cable is capable of supporting a maximum load of 500 lb (227 kg). Additional support is necessary if the section of the window unit requiring support exceeds 500 lb (227 kg). Radius top windows cannot be use as bay windows.
			4.	Cable Support System: 1/8 inch (3.2 mm) diameter braided steel cable with hardware required for complete installation.
	** NOTE TO SPECIFIER ** Delete if not required.
		J.	Insect Screens
	** NOTE TO SPECIFIER ** Delete insect screen not required.
			1.	Insect Screens: Provide venting sash with an insect screen, including attachment hardware.
				a.	Insect Screen Cloth: 18 by 16 (1.0 by 1.1 mm) count per sq. inch aluminum mesh, gunmetal finish.
	** NOTE TO SPECIFIER ** Delete frame not required.
				b.	Frames: Full height 0.024 inch (0.61 mm) rolled aluminum frame with chromate conversion coating. Provide matching corner locks and latch retainers.
				c.	Frames: Half height 0.024 inch (0.61 mm) rolled aluminum frame with chromate conversion coating. Provide matching corner locks and latch retainers.
				d.	Frame Finish: High-bake polyester finish in the following color:
	** NOTE TO SPECIFIER ** Delete color not required.
					1)	Color: White.
					2)	Color: Stone.
					3)	Color: Gold Dust.
					4)	Color: Sandtone.
					5)	Color: Terratone.
					6)	Color: Forest Green.
					7)	Color: Canvas.
					8)	Color: Dove Gray.
					9)	Color: Prairie Grass.
					10)	Color: Red Rock.
					11)	Color: Cocoa Bean.
					12)	Color: Dark Bronze.
					13)	Color: Black.
			2.	Insect Screen: Provide TruScene at venting sash with attachment hardware.
				a.	Insect Screen Cloth: 25 by 25 count per square inch (9.84252 per sq cm) micro fine stainless steel wire with a polyester non-reflective coating.
	** NOTE TO SPECIFIER ** Delete frame not required.
				b.	Frames: Full height 0.024 (0.61 mm) inch rolled aluminum frame with chromate conversion coating and polyester painted finish.
				c.	Frames: Half height 0.024 (0.61 mm) inch rolled aluminum frame with chromate conversion coating and polyester painted finish.
				d.	Frame Finish: Polyester finish in the following color:
	** NOTE TO SPECIFIER ** Delete color not required.
					1)	Color: White.
					2)	Color: Stone.
					3)	Color: Gold Dust.
					4)	Color: Sandtone.
					5)	Color: Terratone.
					6)	Color: Forest Green.
					7)	Color: Canvas.
					8)	Color: Dove Gray.
					9)	Color: Prairie Grass.
					10)	Color: Red Rock.
					11)	Color: Cocoa Bean
					12)	Color: Dark Bronze.
					13)	Color: Black.
				e.	Wood Frames for Awning, Casement and Venting Transom Window Insect Screens: Full height.
	** NOTE TO SPECIFIER ** Delete wood species not required.
					1)	Species: Pine.
					2)	Species: Oak.
					3)	Species: Maple.
	** NOTE TO SPECIFIER ** Delete wood finish not required.
					4)	Finish: Unfinished.
					5)	Finish: Clear coat finish.
					6)	Finish: Stain Color - Cinnamon.
					7)	Finish: Stain Color - Espresso.
					8)	Finish: Stain Color - Honey.
					9)	Finish: Stain Color - Mocha.
					10)	Finish: Stain Color - Russet.
					11)	Match window interior unit wood species and finish.
		K.	Fabrication
			1.	Preservative Treatment: Treat wood sash and frame members after machining with a water repellent preservative per WDMA I.S.4.
	** NOTE TO SPECIFIER ** Delete if not required..
			2.	Double-Hung, Casement, Awning, Venting Transom Units:
	** NOTE TO SPECIFIER ** Extruded Fibrex is required to produce radius top units, transom and picture windows. Delete outer frame not required.
				a.	Outer Frame: Fibrex material laminated to wood core with PVC end caps.
				b.	Outer Frame (Radius Units): Extruded Fibrex material adhesively bonded corner keys. Mechanically fasten sill assembly and wood sub-frame components. Bond outer frame members to sub-frame with adhesive and mechanical fasteners.
				c.	Sill: Fibrex material.
				d.	Bond outer frame members and sill to wood base frame with adhesive.
	** NOTE TO SPECIFIER ** Delete Jamb and Head Jamb Liners not required.
				e.	Jamb and Head Jamb Liners (Pine):
					1)	Side Jamb Liner: Solid pine filler attached to a rigid PVC vinyl extrusion.
					2)	Head Jamb Liner: Solid pine head parting stop and interior aesthetic filler with rigid PVC vinyl head liner.
				f.	Jamb and Head Jamb Liners (Oak and maple):
					1)	Side Jamb Liner: Oak or maple veneer over solid, finger-joined pine filler attached to rigid PVC vinyl extrusion.
					2)	Head Jamb Liner: Oak or maple veneer over solid, finger-joined pine parting stop and interior aesthetic filler with a rigid PVC vinyl head liner.
				g.	Sash Components:
					1)	Exterior Sash: Pultruded fiberglass material with adhesively bonded PVC corner keys.
					2)	Interior Sash: Clear or veneer wood adhesively applied to exterior sash components.
	** NOTE TO SPECIFIER ** Delete if not required..
			3.	Picture and Transom Units:
				a.	Outer Frame: Pultruded fiberglass material with adhesively bonded PVC corner keys.
				b.	Interior Sash: Provide clear wood interior sash components clip fastened to exterior sash profile.
				c.	Provide clear or veneer wood stops.
				d.	Mechanically fasten sill assembly and wood sub frame components. Bond outer frame members to sub-frame with adhesive and mechanical fasteners.
			4.	Glazing: Factory glazed with glazing sealant.
			5.	Weatherstripping: Factory-applied to unit frame. Field-applied interlocking weatherstripping at panel meeting stiles.
	** NOTE TO SPECIFIER ** Delete if not required.
	2.3	SLIDING PATIO DOORS
		A.	Gliding Patio Doors:
			1.	Product: Andersen® A-Series Gliding Patio Doors.
		B.	Materials:
	** NOTE TO SPECIFIER ** Retain Certified Wood Paragraph below if wood doors are required to be certified for LEED or project is being designed with sustainable practices.
			1.	Certified Wood: Doors shall be certified as "FSC Mixed Credit" per FSC STD-01-001, "FSC Principles and Criteria for Forest Stewardship," and FSC STD-40-004, "FSC Standard for Chain of Custody Certification."
			2.	Wood Members: Fabricated from wood species approved in WDMA I.S.4.
			3.	Reinforced engineered plastic fiberglass frame cover: Comply with ASTM D3647.
			4.	Urethane Coating: High durability coating conforming to color uniformity, chemical resistance, detergent resistance, and weather resistance requirements of AAMA 2603.
			5.	Sill: Reinforced engineered plastic fiberglass
			6.	Weatherstripping:
				a.	Head Jamb weatherstripping for operating panel: Polypropylene pile with fin seal.
				b.	Sill weatherstripping: Foam filled Polyethylene leaf seal.
				c.	Side Jambs: Polypropylene pile with fin seal at operating side jamb and foam filled polyethylene leaf seal at stationary side jamb.
				d.	Meeting Stiles: PVC scissors interlock weatherstrip with silicone bulb primary weatherstrip.
		C.	Hardware:
			1.	Roller Assembly: Provide operating panels with adjustable roller assembly consisting of self-lubricating tandem wheels operating on ball bearings. Provide 2-tandem rollers for each operating panel.
	** NOTE TO SPECIFIER ** 6-pin key cylinder is optional. Retain, edit, or delete the following paragraph to suit project requirements.
			2.	Latch Levers: Forged brass or zinc die cast thumb-turn-operated reach- out dual multi-point hook bolt locking mechanism. Design lock to prevent automatic locking when door is closed.
	** NOTE TO SPECIFIER ** Retain one of the following two options per project requirements.
				a.	Provide blank cover at exterior.
				b.	Provide 6-pin keyed cylinder.
	** NOTE TO SPECIFIER ** Optional auxiliary and 6-pin key cylinder exterior keyed locks shipped separately. ** NOTE TO SPECIFIER ** Select between the following hardware styles. Delete styles not required for project.
			3.	Hardware Styles: Provide the following hardware where indicated:
				a.	Newbury® Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware lock finishes below. Delete finishes not required.
					1)	Finish: Bright Brass.
					2)	Finish: Antique Brass.
					3)	Finish: Polished Chrome.
					4)	Finish: Brushed Chrome.
					5)	Finish: Oil Rubbed Bronze.
					6)	Finish: Satin Nickel.
				b.	Metro™ Hardware: Cast zinc dichromate thumb turn and operating handle pull with powder coated painted finish in the following color:
	** NOTE TO SPECIFIER ** Retain one of the following hardware colors below. Delete colors not required.
					1)	Color: White.
					2)	Color: Stone.
				c.	Covington™ Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Finish: Bright Brass.
					2)	Finish: Antique Brass.
					3)	Finish: Oil Rubbed Bronze.
				d.	Encino® Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Finish: Distressed Bronze.
					2)	Finish: Distressed Nickel.
				e.	Yuma® Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Finish: Distressed Bronze.
					2)	Finish: Distressed Nickel.
				f.	Anvers® Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete colors not required.
					1)	Finish: Bright Brass.
					2)	Finish: Oil Rubbed Bronze.
					3)	Finish: Satin Nickel.
				g.	Whitmore® Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Finish: Bright Brass.
					2)	Finish: Antique Brass.
					3)	Finish: Oil Rubbed Bronze.
					4)	Finish: Satin Nickel.
				h.	Albany® Hardware: Cast zinc dichromate thumb turn and lever handle trim with powder coated painted finish in the following color:
	** NOTE TO SPECIFIER ** Retain one of the following hardware colors below. Delete colors not required.
					1)	Color: Gold Dust.
					2)	Color: White.
					3)	Color: Black.
					4)	Color: Stone.
	** NOTE TO SPECIFIER ** Auxiliary foot locks are optional on 2 and 4 panel doors. Delete paragraph if not required.
			4.	Auxiliary Foot Lock: Provide operating panels with auxiliary foot lock consisting of a spring loaded plunger that engages in a grommet in the sill. Provide auxiliary foot locks in the following finish or color:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes or colors below. Delete finishes or colors not required.
				a.	Finish: Bright Brass.
				b.	Finish: Antique Brass.
				c.	Finish: Polished Chrome.
				d.	Finish: Brushed Chrome.
				e.	Finish: Oil Rubbed Bronze.
				f.	Finish: Satin Nickel.
				g.	Finish: Distressed Bronze.
				h.	Finish: Distressed Nickel.
				i.	Color: Stone.
				j.	Color: White.
				k.	Color: Gold dust.
	** NOTE TO SPECIFIER ** Specify subordinate or secondary items that aid and assist primary products specified above or are necessary for preparation or installation of those items.
		D.	Accessories:
			1.	Provide wood interior extension jamb members machined from clear or veneered, finger joined clear material approved in ANSI/AAMA/NWWDA 101/I.S.2. Pre-drill extension jambs for application.
			2.	Exterior Trim and Casing: Where indicated on Drawings, provide Fibrex® material in the following thickness, conforming to NIST Voluntary Product Standards P.S.1 and rigid vinyl channels.
				a.	Thickness: 1/2 inch (13 mm).
				b.	Color: Match patio door framing.
				c.	Andersen® Fibrex material trim kits:
	** NOTE TO SPECIFIER ** Retain one of the following widths below.
					1)	Trim Width: 3-1/2 inches (89 mm) Flat.
					2)	Trim Width: Brickmold.
	** NOTE TO SPECIFIER ** Retain subparagraph above for andersen® vinyl trim board. retain subparagraph below for vinyl laminated board.
				d.	Support Mullion Trim: 2 inch (51 mm) wide wood filler and vinyl trim strip.
					1)	Color: Match door unit exterior color.
		E.	Insect Screens:
	** NOTE TO SPECIFIER ** Select between the gliding or retractable Insect screen options.
			1.	Gliding Insect Screens: Provide gliding patio doors with gliding insect screen installed on exterior.
				a.	Insect Screen Door Frame: 0.040 inch (1 mm) roll formed aluminum frame with chromate conversion coating in the following polyester painted color.
	** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete subparagraphs not required.
					1)	Color: White.
					2)	Color: Sandtone.
					3)	Color: Terratone®.
					4)	Color: Forest Green
					5)	Color: Black
					6)	Color: Coco Bean
					7)	Color: Dove Grey
					8)	Color: Canvas
					9)	Color: Red Rock
					10)	Color: Prairie Grass
					11)	Color: Dark Bronze
				b.	Insect Screen Cloth: 18 by 16 glass fiber mesh, charcoal color finish.
				c.	Rollers: Insect screen doors operate on injection molded bottom rollers with self contained leveling adjusters engaged in sill track.
				d.	Operating Handles: Polycarbonate operating handles to receive locking mechanism in the following color.
	** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete subparagraphs not required.
					1)	Color: White.
					2)	Color: Stone.
					3)	Color: Black
					4)	Color: Coco Bean
					5)	Color: Dove Grey
					6)	Color: Canvas
					7)	Color: Red Rock
					8)	Color: Prairie Grass
					9)	Color: Dark Bronze
			2.	Retractable Insect Screens: Provide gliding patio doors with retractable insect screen installed on exterior.
				a.	Insect Screen Door Housing: Extruded aluminum housing in the following color.
	** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete subparagraphs not required.
					1)	Color: White.
					2)	Color: Sandtone.
					3)	Color: Terratone®.
					4)	Color: Forest Green finish.
					5)	Color: Black
					6)	Color: Coco Bean
					7)	Color: Dove Grey
					8)	Color: Canvas
					9)	Color: Red Rock
					10)	Color: Prairie Grass
					11)	Color: Dark Bronze
				b.	Insect Screen Cloth: 18 by 16 glass fiber mesh, charcoal color finish.
			3.	Top Hung Gliding Insect Screens: Provide gliding patio doors with gliding insect screen installed on exterior.
				a.	Insect Screen Door Frame: 0.040 inch (1 mm) roll formed aluminum frame with chromate conversion coating in the following polyester painted color.
	** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete subparagraphs not required.
					1)	Color: White.
					2)	Color: Sandtone.
					3)	Color: Terratone®.
					4)	Color: Forest Green finish.
					5)	Color: Black
					6)	Color: Coco Bean
					7)	Color: Dove Grey
					8)	Color: Canvas
					9)	Color: Red Rock
					10)	Color: Prairie Grass
					11)	Color: Dark Bronze
				b.	Insect Screen Cloth: 18 by 16 glass fiber mesh, charcoal color finish.
	** NOTE TO SPECIFIER ** Describe items that must be shop manufactured, fabricated, or assembled before being delivered to the site.
		F.	Fabrication:
			1.	Preservative Treatment: Treat wood frame and door panel wood members after machining with a water repellent preservative per WDMA I.S.4.
			2.	Frame Components:
				a.	Corner Fastening: Dual dowel and water resistant structural adhesive.
				b.	Attach reinforced engineered plastic frame cover to wood frame.
				c.	Factory-apply urethane coating (2.6 mil minimum dry film thickness) to exterior exposed surfaces of sensitized, reinforced, engineered plastic frame cover.
			3.	Door Panels:
				a.	Stiles: 1-1/2 inch (38 mm) LVL wood core. Provide solid wood edge strips, phenolic interior and exterior outer substrate, and spliced veneer interior surface.
					1)	8 foot (2438 mm) units use laminated veneer lumber core.
				b.	Top Rails: Solid, clear material or finger joined and edge glued wood core. Provide solid wood edge strips, phenolic interior and exterior outer substrate, and spliced veneer interior surface.
				c.	Bottom Rails: Laminated construction consisting of spliced veneer interior surface over laminated veneer lumber core with phenolic overlay interior and exterior outer substrate.
				d.	Panel Finish:
	** NOTE TO SPECIFIER ** Retain appropriate option below or change to change to project staining section.
					1)	Interior: Unfinished, natural clear veneer of the following species to receive field applied paint or stain finish as specified in the painting section.
					2)	Interior: Natural clear veneer of the following species shall be prefinished.
	** NOTE TO SPECIFIER ** Retain project required veneer subparagraph below. Delete subparagraphs not required.
						a)	Species: Oak.
						b)	Species Type: Maple.
						c)	Species Type: Pine.
						d)	Finish Type: Water based
							1)	Prefinished Painted White Pine interior.
							2)	Prefinished Painted Birch Bark interior.
							3)	Prefinished Painted Prime interior.
							4)	Prefinished stained clear coat interior.
							5)	Prefinished stained Honey interior.
							6)	Prefinished stained Cinnamon interior.
							7)	Prefinished stained Russet interior.
							8)	Prefinished stained Mocha interior.
							9)	Prefinished stained Espresso interior.
							10)	Exterior: Factory-applied, high durability, urethane coating in the following color:
	** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete subparagraphs not required.
								a)	Color: White.
								b)	Color: Sandtone.
								c)	Color: Terratone®.
								d)	Color: Forest Green finish.
								e)	Color: Black.
								f)	Color: Coco Bean.
								g)	Color: Dove Grey.
								h)	Color: Canvas.
								i)	Color: Red Rock.
								j)	Color: Prairie Grass.
								k)	Color: Dark Bronze.
			4.	Weatherstripping: Factory-applied to unit frame. Field-apply interlocking weatherstripping at panel meeting stiles.
			5.	Glazing: Factory-glazed with glazing sealant and wood interior trim stops.
	** NOTE TO SPECIFIER ** Delete if not required.
	2.4	HINGED PATIO DOORS
		A.	Proprietary Products/Systems:
	** NOTE TO SPECIFIER ** Delete door type not required.
			1.	Product: Andersen® A-Series Hinged Patio Doors.
			2.	Product: Andersen® A-Series Outswing Patio Doors.
			3.	Product: Andersen® A-Series Patio Door Sidelights.
			4.	Product: Andersen® A-Series Patio Door Transoms.
	** NOTE TO SPECIFIER ** Specify materials to be furnished. This article may be omitted and the materials can be included with the description of a manufactured unit, equipment, component, or accessory.
		B.	Materials:
	** NOTE TO SPECIFIER ** Retain Certified Wood Paragraph below if wood doors are required to be certified for LEED or project is being designed with sustainable practices.
			1.	Certified Wood: Doors shall be certified as "FSC Mixed Credit" per FSC STD-01-001, "FSC Principles and Criteria for Forest Stewardship," and FSC STD-40-004, "FSC Standard for Chain of Custody Certification."
			2.	Wood Members: Fabricated from wood species approved in WDMA I.S.4.
			3.	Reinforced engineered plastic fiberglass frame cover: Comply with ASTM D3647.
			4.	Urethane Coating: Durable coating conforming to color uniformity, chemical resistance, detergent resistance, and weather resistance requirements of AAMA 2603.
			5.	Weatherstripping: Continuous, flexible, compressible bulb type with welded corners.
			6.	Sill: Reinforced engineered plastic fiberglass.
		C.	Hardware:
			1.	Hinges: Ball bearing, adjustable, captured hinge design with cover plate. Hinges allow vertical and rack panel adjustment, in the following finish to match lock trim:
	** NOTE TO SPECIFIER ** Retain one of the following hardware lock colors below. Delete colors not required.
				a.	Finish: Bright Brass.
				b.	Finish: Antique Brass.
				c.	Finish: Polished Chrome.
				d.	Finish: Brushed Chrome.
				e.	Finish: Oil Rubbed Bronze.
				f.	Finish: Satin Nickel.
				g.	Finish: Distressed Bronze.
				h.	Finish: Distressed Nickel.
				i.	Finish: Gold Dust.
				j.	Finish: Black.
			2.	Hinges for Doors with Prefinished White Interior: Prefinished White zinc die cast.
				a.	Other interior finished or unfinished doors will default to Gold Dust colored hinges, steel adjustable, captured hinge design with ball bearing pivots.
			3.	Locks: Stainless steel locking mechanism consisting of lever handle operated latch and 3-point deadbolt lock mechanism. 3-point locking mechanism consists of thumb turn operated 0.787 inch (20 mm) metal deadbolt, which when projected, locks 2 additional hook bolts engaging active panel.
				a.	Provide 6-pin keyed cylinder and thumb turn at interior.
			4.	Coastal Upgrade for AP/PA Units: 5-point stainless steel lock.
			5.	Lever Handle Trim: Provide the following trim style and finish where indicated:
	** NOTE TO SPECIFIER ** Select between the following hardware styles.
				a.	Newbury® Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Finish: Bright Brass.
					2)	Finish: Antique Brass.
					3)	Finish: Polished Chrome.
					4)	Finish: Brushed Chrome.
					5)	Finish: Oil Rubbed Bronze.
					6)	Finish: Satin Nickel.
				b.	Covington™ Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Finish: Bright Brass.
					2)	Finish: Antique Brass.
					3)	Finish: Oil Rubbed Bronze.
				c.	Encino® Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Finish: Distressed Bronze.
					2)	Finish: Distressed Nickel.
				d.	Yuma® Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Finish: Distressed Bronze.
					2)	Finish: Distressed Nickel.
				e.	Anvers® Hardware: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Finish: Bright Brass.
					2)	Finish: Oil Rubbed Bronze.
					3)	Finish: Satin Nickel.
				f.	Whitmore®: Forged brass thumb turn and operating handle pull with the following finish:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Finish: Bright Brass.
					2)	Finish: Antique Brass.
					3)	Finish: Oil Rubbed Bronze.
					4)	Finish: Satin Nickel.
				g.	Tribeca® Hardware: Cast zinc dichromate thumb turn and lever handle trim with powder coated painted finish in the following color:
	** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not required.
					1)	Color: White.
					2)	Color: Stone.
	** NOTE TO SPECIFIER ** Specify subordinate or secondary items that aid and assist primary products specified above or are necessary for preparation or installation of those items.
		D.	Accessories:
			1.	Exterior Trim and Casing: Where indicated on Drawings, provide vinyl sheathed plywood in the following thickness, conforming to NIST Voluntary Product Standards P.S.1 and rigid vinyl channels.
				a.	Thickness: 1/2 inch (12.7 mm).
	** NOTE TO SPECIFIER ** Retain thickness above or below.
				b.	Thickness: 3/4 inch (19 mm).
				c.	Color: Match door framing.
				d.	Vinyl Trim Board: 0.043 inch (1.09 mm) thick vinyl with lightly textured surface laminated with adhesive to 3/4 inch (19 mm) thick plywood.
	** NOTE TO SPECIFIER ** Retain subparagraph above for andersen® vinyl trim board. Retain subparagraph below for vinyl laminated board.
				e.	Vinyl Laminated Board: 0.045 inch (1.14 mm) thick vinyl with smooth surface laminated with adhesive to 1/2 inch (12.7 mm) thick plywood.
				f.	Trim Channels: Rigid vinyl extrusions furnished by door manufacturer for use on same product line.
				g.	Jamb Depth:
					1)	Inswing 4-9/16 inches and 6 9/16 inch (116 mm).
					2)	Outswing 4-9/16 inches (116 mm).
					3)	Sidelights and Transoms 4-9/16 inches (116 mm).
			2.	Interior Extension Jambs: Solid or veneered wood in the following species and depths:
	** NOTE TO SPECIFIER ** Retain project required species subparagraph below and delete subparagraphs not required.
				a.	Species: Maple.
				b.	Species: Pine.
				c.	Species: Oak.
				d.	Species: Prefinished Pine.
	** NOTE TO SPECIFIER ** Retain project required jamb width subparagraph below and delete subparagraphs not required.
				e.	Jamb Width: Available in 1/16 inch (1.6 mm) depths up to 7-1/8 inches (181 mm):
			3.	A-Series Outswing Door Panel Stop: Provide panel stops fabricated from the following species:
	** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete subparagraphs not required.
				a.	Species: Pine.
				b.	Species: Oak.
				c.	Species: Maple.
				d.	Species: Painted.
			4.	A-Series Hinged Inswing and Outswing Door Threshold: Provide threshold fabricated from the following species:
				a.	Species: Oak.
	** NOTE TO SPECIFIER ** Retain species above or below.
				b.	Species: Mahogany.
			5.	Exterior Keyed Lock: 6-pin keyed lock system.
			6.	Support Mullion Trim: 2 inch (51 mm) wide wood filler and vinyl trim strip.
				a.	Color: Match door unit exterior color.
			7.	Provide wood interior extension jamb members machined from clear or veneered, finger joined clear material approved in ANSI/AAMA/NWWDA 101/I.S.2. Pre-drill extension jambs for application.
		E.	Insect Screens:
			1.	Hinged Door Insect Screens: Provide hinged patio doors with an insect screen installed on exterior.
				a.	Insect Screen Door Frame: 0.040 inch (1.02 mm) roll formed aluminum frame with chromate conversion coating.
				b.	Hinged Insect Screen Door Frame for Single Panel and Active Passive Units: 0.040 inch (1.02 mm) extruded aluminum frame with chromate conversion coating. Provide hinged insect screen doors complete with hinges, closers, and latches.
				c.	Double-Hinged Insect Screen: 0.040 inch (1.02 mm) aluminum frame with chromate conversion coating.
					1)	Perma-Clean® Top Hung Gliding Insect Screens: Provide Inswing hinged patio doors with gliding insect screen installed on exterior for Active Stationary or 3 panel configurations.
				d.	Insect Screen Cloth: 18 by 16 glass fiber mesh, charcoal color finish.
				e.	Frame Finish:
	** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete subparagraphs not required.
					1)	Color: White.
					2)	Color: Sandtone.
					3)	Color: Terratone®.
					4)	Color: Forest Green.
					5)	Color: Cocoa Bean.
					6)	Color: Red Rock.
					7)	Color: Black.
					8)	Color: Prairie Grass.
					9)	Color: Canvas.
					10)	Color: Dove Grey.
				f.	Rollers: Insect screen doors operate on injection molded bottom rollers with self contained leveling adjusters engaged in sill track.
				g.	Operating Handles: Polycarbonate operating handles to receive locking mechanism in the following color.
	** NOTE TO SPECIFIER ** Retain project required color subparagraph below. delete subparagraphs not required. "Polane" is a registered trademark of the Sherwin-Williams Company.
					1)	Color: White.
					2)	Color: Stone.
					3)	Color: Forest Green.
					4)	Color: Cocoa Bean.
					5)	Color: Red Rock.
					6)	Color: Black.
					7)	Color: Prairie Grass.
					8)	Color: Canvas.
					9)	Color: Dove Grey.
				h.	Polane® coating, 6063 aluminum extrusion with corner locks and drive rivet fastening system.
				i.	Color: Match patio door unit exterior color.
			2.	Outswing Door Insect Screens: Provide outswing hinged patio doors with retractable insect screen installed on interior jamb.
				a.	Retractable Insect Screen Housing Assembly: Aluminum with white painted finish.
				b.	Insect Screen Cloth: 18 by 16 glass fiber mesh, charcoal color finish.
	** NOTE TO SPECIFIER ** Describe items that must be shop manufactured, fabricated, or assembled before being delivered to the site.
		F.	Fabrication:
			1.	Preservative Treatment: Treat wood frame and door panel wood members after machining with water repellent preservative per WDMA I.S.4.
			2.	Frame Components:
				a.	Attach reinforced engineered plastic frame cover to wood frame.
				b.	Factory-applied urethane coating (2.6 mil minimum dry film thickness) to exterior exposed surfaces of sensitized, reinforced, engineered plastic frame cover.
			3.	Door Panels:
				a.	Stiles and Top Rails: Finger joined and edge glued wood core or LVL, 1-3/4 inches (44 mm) thick before milling. Provide solid wood edge strips, phenolic interior and exterior outer substrate, and veneered interior surface.
				b.	Bottom Rails: Laminated construction consisting of veneer interior surface over laminated veneer lumber core with phenolic overlay interior and exterior outer substrate.
				c.	Corner Fastening:
					1)	Door Units: Joint/corners are secured with hardwood dowels and water-resistant structural adhesive.
					2)	Sidelight and Transom Units: Multi-surface butt joint with adhesive, silicone and 2 wood screws.
				d.	Door Panel Finish:
	** NOTE TO SPECIFIER ** Retain appropriate option below or change to change to project staining section.
					1)	Interior: Unfinished, natural clear veneer of the following species to receive field applied paint or stain finish as specified in the painting section.
					2)	Interior: Natural clear veneer of the following species shall be prefinished.
	** NOTE TO SPECIFIER ** Retain project required veneer subparagraph below. Delete subparagraphs not required.
						a)	Species: Oak.
						b)	Species: Maple.
						c)	Species: Pine.
						d)	Finish Type: Prefinished water based Painted or Stained interior.
							1)	Prefinished Painted White Pine interior.
							2)	Prefinished Painted Birch Bark interior.
							3)	Prefinished Painted Prime interior.
							4)	Prefinished stained clear coat interior.
							5)	Prefinished stained Honey interior.
							6)	Prefinished stained Cinnamon interior.
							7)	Prefinished stained Russet interior.
							8)	Prefinished stained Mocha interior.
							9)	Prefinished stained Espresso interior.
					3)	Exterior: Factory-applied, high durability, urethane coating in the following color:
	** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete subparagraphs not required.
						a)	Color: White.
						b)	Color: Sandtone.
						c)	Color: Terratone®.
						d)	Color: Forest Green.
						e)	Color: Cocoa Bean.
						f)	Color: Red Rock.
						g)	Color: Black.
						h)	Color: Prairie Grass.
						i)	Color: Canvas.
						j)	Color: Dove Grey finish.
			4.	Sill: Reinforced Engineered Plastic "Fiberglass".
			5.	Weatherstripping: Factory-applied to panel.
			6.	Glazing: Factory-glazed with silicone glazing and interior wood glazing stops.
	** NOTE TO SPECIFIER ** Select glass and grilles for windows and doors selected for project. Delete provisions not required for project.
	2.5	GLAZING AND GRILLES
		A.	Glazing:
			1.	General: Tempered insulating glass units certified through the Insulating Glass Certification Council as conforming to the requirements of IGCC. Provide dual sealed units consisting of polyisobutylene primary seal and silicone secondary seal. Provide metal spacers with bent or soldered corners.
	** NOTE TO SPECIFIER ** Retain certification requirements paragraph above or below.
			2.	General: Tempered insulating glass units certified through the Insulating Glass Manufacturers Association of Canada (IGMAC) conforming to the requirements of Canadian General Standards Board CAN/CGSB 12.8 or ASTM E2190. Provide dual sealed units consisting of polyisobutylene primary seal and silicone secondary seal. Provide metal spacers with bent or soldered corners.
	** NOTE TO SPECIFIER ** Select between the following standard glazing options. Consult Andersen Corporation for additional glazing options. Consult Andersen Corporation for assistance in selecting appropriate glazing type.
			3.	High-Performance™ Low-E4® Argon Gas Blend Filled Insulating Glass Units:
				a.	Glass: Tempered insulating glass units consisting of an outboard and inboard lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3, Kind FT.
				b.	Magnetron sputtering vapor deposition (MSVD) TiO2 coating applied to the No. 1 surface.
				c.	High-Performance Low-E4 Glass Coating: Magnetron sputtering vapor deposition (MSVD) Low-E coating applied to the No. 2 surface.
				d.	Filling: Fill space between glass lites with argon gas blend.
				e.	Protective removable polyolefin film applied to glass surfaces No. 1 and No. 4.
			4.	High-Performance Low-E4 Sun Glass, Low SHGC, Argon Gas Blend Filled Insulating Glass Units:
				a.	Glass: Tempered insulating glass units consisting of an outboard and inboard lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3, Kind FT.
				b.	Magnetron sputtering vapor deposition (MSVD) TiO2 coating applied to the No. 1 surface.
				c.	High-Performance Low-E4 Sun Glass Coating: Magnetron sputtering vapor deposition (MSVD) Low-E coating applied to the No. 2 surface.
				d.	Filling: Fill space between glass lites with argon gas blend.
				e.	Protective removable polyolefin film applied to glass surfaces No. 1 and No. 4.
			5.	SmartSun™Low-E Glass, Low SHGC, Argon Gas Blend Filled Insulating Glass Units:
				a.	Glass: Tempered insulating glass units consisting of an outboard and inboard lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3, Kind FT.
	** NOTE TO SPECIFIER ** Where patterned glass is required for project, delete paragraph above and retain paragraph below with appropriate patterned glass type. Delete types not required for project.
				b.	Glass: Tempered insulating glass units consisting of an outboard lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3, Kind FT and the following patterned glass:
				c.	Inboard Pattern Glass Lite:
					1)	Cascade.
					2)	Fern.
					3)	Obscure.
					4)	Reed.
				d.	Air Space: 3/4 inch (19 mm).
				e.	SmartSun™ Low-E Glass Coating: Magnetron sputtering vapor deposition (MSVD) Low-E coating applied to the No. 2 surface.
				f.	Filling: Fill space between glass lites with argon gas blend.
			6.	High-Performance™ Low-E4® SmartSun Glass, Low SHGC, Argon Gas Blend Filled Insulating Glass Units:
				a.	Glass: Tempered insulating glass units consisting of an outboard and inboard lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3, Kind FT.
	** NOTE TO SPECIFIER ** Where patterned glass is required for project, delete paragraph above and retain paragraph below with appropriate patterned glass type. Delete types not required for project.
				b.	Glass: Tempered insulating glass units consisting of an outboard lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3, Kind FT and the following patterned glass:
				c.	Inboard Pattern Glass Lite:
					1)	Cascade.
					2)	Fern.
					3)	Obscure.
					4)	Reed.
				d.	Air Space: 3/4 inch (75 mm).
				e.	Magnetron sputtering vapor deposition (MSVD) TiO2 coating applied to the No. 1 surface.
				f.	High-Performance Low-E4 Sun Glass Coating: Magnetron sputtering vapor deposition (MSVD) Low-E coating applied to the No. 2 surface.
				g.	Filling: Fill space between glass lites with argon gas blend.
				h.	Protective removable polyolefin film applied to glass surfaces No. 1 and No. 4.
	** NOTE TO SPECIFIER ** Select between the two impact resistant glass types if impact resistant glazing required.
			7.	Monolithic Impact Glass:
				a.	Impact Resistant Glazing: Provide impact resistant glazing that has been tested per ASTM E1996 large missile impact requirements.
				b.	Glass: Impact resistant glass consisting of two (2) lites of clear annealed glass conforming to ASTM C1036, Type 1, Class 1, q3, Kind LA, laminated with 0.090 inch (2.3 mm) polyvinyl butyral interlayer in the following color:
	** NOTE TO SPECIFIER ** Retain project required color below. Delete colors not required.
					1)	Color: Clear.
					2)	Color: Gray tinted.
				c.	Protective removable polyolefin film applied to glass surfaces No. 1 and No. 2.
			8.	Insulating Impact Resistant Glass:
				a.	Impact Resistant Glazing: Provide impact resistant glazing that has been tested per ASTM E1996 large missile impact requirements.
				b.	Glass: Insulating glass units consisting of an outboard lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3, Kind FT, and a laminated inboard lite of cleared annealed glass conforming to ASTM C1036, Type 1, Class 1, q3, Kind LA, laminate with a 0.090 inch (2.3 mm) polyvinyl butyral interlayer.
				c.	Magnetron sputtering vapor deposition (MSVD) TiO2 coating applied to the No. 1 surface.
				d.	High-Performance Low-E4 Coating: Magnetron sputtering vapor deposition (MSVD) Low-E coating applied to the No. 2 surface.
	** NOTE TO SPECIFIER ** Retain subparagraph above for standard low-e coating. Retain subparagraph below for sun low-e coating.
				e.	High-Performance™ Low-E4® Sun Glass: Magnetron sputtering vapor deposition (MSVD) Low-E coating applied to the No. 2 surface.
				f.	Filling: Fill space between glass lites with argon gas blend.
				g.	Protective removable polyolefin film applied to glass surfaces No. 1 and No. 4.
		B.	Grilles:
	** NOTE TO SPECIFIER ** Interior grilles can be fixed or permanently applied Fibrex® material or wood as selected below. Fixed interior grilles must be used in conjunction with fixed exterior grilles. Consult specifications for grille material of adjacent unit for joined units of different types. Consult an Andersen representative for additional grille options. ** NOTE TO SPECIFIER ** Coordinate specifications for grille material of adjacent unit for joined units of different types. Refer to Andersen® Divided Light Pattern Guide for available divided light patterns and details. Exterior and interior colors can be different colors. Retain project required grille pattern subparagraph below and delete subparagraphs not required. Full divided light and Finelight grilles are not available for impact resistant glazed products.
			1.	Full Divided Light Grilles: Fixed exterior and interior grilles with an anodized aluminum muntin bar, 1/2 inch (13 mm) wide, to match spacer within insulated glass unit where indicated on Drawings.
				a.	Exterior Grille: Provide Fibrex material exterior grilles where indicated on Drawings. Install grilles on exterior of glass with adhesive tape to simulate true divided light muntin bars in the following color:
					1)	Color: White.
					2)	Color: Stone.
					3)	Color: Sandtone.
					4)	Color: Forest Green.
					5)	Color: Black.
					6)	Color: Coco Bean.
					7)	Color: Dove Grey.
					8)	Color: Canvas.
					9)	Color: Red Rock.
					10)	Color: Prairie Grass.
					11)	Color: Dark Bronze
					12)	Color: Terratone.
				b.	Fixed Interior grille: Provide profiled wood grilles applied with adhesive tape to interior glass surface.
					1)	Grille Type: Unfinished Maple.
					2)	Grille Type: Unfinished Oak.
					3)	Grille Type: Unfinished Pine.
					4)	Grille Type: White Fibrex material.
					5)	Grille Type: Primed wood.
					6)	Grille Type: Finished wood.
						a)	Finished Wood Type: Oak.
						b)	Finished Wood Type: Pine.
						c)	Finished Wood Type: Maple.
						d)	Finish Color: Clear Coat.
						e)	Finish Color: Honey Stain.
						f)	Finish Color: Cinnamon Stain.
						g)	Finish Color: Russet Stain.
						h)	Finish Color: Mocha Stain.
						i)	Finish Color: Espresso Stain.
						j)	Finish Color: Andersen White Paint.
						k)	Finish Color: Birch Bark Paint.
	** NOTE TO SPECIFIER ** Retain project required grille width subparagraph below. Delete subparagraphs not required.
				c.	Width: 3/4 inch (19 mm).
				d.	Width: 7/8 inch (22 mm).
				e.	Width: 1-1/8 inches (29 mm).
				f.	Width: 2-1/4 inches (57mm).
				g.	Pattern as indicated on Drawings.
			2.	Simulated Divided Light Grilles: Fixed exterior grilles with fixed or removable interior grilles where indicated on Drawings.
				a.	Exterior Grille: Provide Fibrex material exterior grilles where indicated on Drawings. Install grilles on exterior of glass with continuous adhesive tape to simulate true divided light muntin bars in the following color:
					1)	Color: White.
					2)	Color: Terratone.
					3)	Color: Sandtone.
					4)	Color: Black.
					5)	Color: Coco Bean.
					6)	Color: Dove Grey.
					7)	Color: Canvas.
					8)	Color: Red Rock.
					9)	Color: Prairie Grass.
					10)	Color: Forest Green.
					11)	Color: Dark Bronze
	** NOTE TO SPECIFIER ** Retain project required interior grille subparagraph below. Delete subparagraphs not required.
				b.	Fixed Interior Grille: Provide profiled wood grilles applied with adhesive tape to interior glass surface.
					1)	Grille Type: Unfinished Maple.
					2)	Grille Type: Unfinished Oak.
					3)	Grille Type: Unfinished Pine.
					4)	Grille Type: White Fibrex material.
					5)	Grille Type: Primed wood.
					6)	Grille Type: Finished wood.
						a)	Finished Wood Type: Oak.
						b)	Finished Wood Type: Pine.
						c)	Finished Wood Type: Maple.
						d)	Finish Color: Clear Coat.
						e)	Finish Color: Honey Stain.
						f)	Finish Color: Cinnamon Stain.
						g)	Finish Color: Russet Stain.
						h)	Finish Color: Mocha Stain.
						i)	Finish Color: Espresso Stain.
						j)	Finish Color: Andersen White Paint.
						k)	Finish Color: Birch Bark Paint.
				c.	Removable Interior Grilles: Provide removable, hardwood maple divided light grilles where indicated on Drawings. Install removable grilles against interior glass, attached with metal fasteners or integral tabs to sash.
	** NOTE TO SPECIFIER ** Delete wood species not required.
					1)	Species: Oak.
					2)	Species: Maple.
	** NOTE TO SPECIFIER ** Delete wood finish not required.
					3)	Finish: Unfinished.
					4)	Finish: Clear coat finish.
					5)	Finish: Stain Color - Cinnamon.
					6)	Finish: Stain Color - Espresso.
					7)	Finish: Stain Color - Honey.
					8)	Finish: Stain Color - Mocha.
					9)	Finish: Stain Color - Russet.
					10)	Finish: Painted Color (Pine) - White.
					11)	Finish: Painted Color (Pine) - Birch Bark.
					12)	Finish: Painted Color (Pine) - Prime.
					13)	Match window interior unit wood species and finish.
	** NOTE TO SPECIFIER ** Retain project required Grille width subparagraph below. Delete subparagraphs not required.
				d.	Width: 3/4 inch (19 mm).
				e.	Width: 7/8 inch (22 mm).
				f.	Width: 1-1/8 inches (29 mm).
	** NOTE TO SPECIFIER ** Not available for Andersen® A-Series Windows only.
				g.	Width: 2-1/4 inches (57mm).
	** NOTE TO SPECIFIER ** Delete pattern not required.
				h.	Pattern: As indicated on Drawings.
				i.	Pattern: Colonial.
				j.	Pattern: Prairie A (9 light).
				k.	Pattern: Prairie (6 light).
				l.	Pattern: Specified equal light.
			3.	Removable Interior Grilles: Provide removable, hardwood maple divided light grilles where indicated on Drawings. Install removable grilles against interior glass, attached with metal fasteners or integral tabs to sash. Provide dual face profile to give muntin bar appearance from both interior and exterior.
	** NOTE TO SPECIFIER ** Oak not available for Andersen® A-Series Doors. Delete species not required.
				a.	Species: Oak.
				b.	Species: Maple.
	** NOTE TO SPECIFIER ** Retain project required exterior facing subparagraph below. Delete subparagraphs not required.
				c.	Exterior Facing: White color painted finish.
				d.	Exterior Facing: Sandtone color painted finish.
				e.	Exterior Facing: Terratone color painted finish.
				f.	Exterior Facing: Black color painted finish.
				g.	Exterior Facing: Canvas color painted finish.
				h.	Exterior Facing: Dove Gray color painted finish.
				i.	Exterior Facing: Red Rock color painted finish.
				j.	Exterior Facing: Prairie Grass color painted finish.
				k.	Exterior Facing: Cocoa Bean color painted finish.
				l.	Exterior Facing: Forest Green color painted finish.
	** NOTE TO SPECIFIER ** Available for Andersen® A-Series Gliding Patio Doors only.
				m.	Exterior Facing. Maple grille with Dark Bronze color painted finish.
	** NOTE TO SPECIFIER ** Retain project required interior facing subparagraph below. Delete subparagraphs not required.
				n.	Interior Facing: Unfinished Maple.
				o.	Interior Facing: Andersen White Painted maple interior.
	** NOTE TO SPECIFIER ** Below available for Andersen® A-Series Doors only.
				p.	Interior Facing: Birch Bark Painted maple interior.
				q.	Interior Facing: Prime Painted maple interior.
				r.	Interior Facing: Painted maple interior.
				s.	Interior Facing: Clear Coat stain maple interior.
				t.	Interior Facing: Honey stain maple interior.
				u.	Interior Facing: Cinnamon stain maple interior.
				v.	Interior Facing: Russet stain maple interior.
				w.	Interior Facing: Mocha stain maple interior.
				x.	Interior Facing: Espresso stain maple interior.
	** NOTE TO SPECIFIER ** Retain project required grille width subparagraph below. Delete subparagraphs not required.
				y.	Width: 3/4 inch (19 mm).
				z.	Width: 7/8 inch (22 mm).
				aa.	Width: 1-1/8 inches (29 mm).
	** NOTE TO SPECIFIER ** Delete pattern not required.
				ab.	Pattern: As indicated on Drawings.
				ac.	Pattern: Colonial.
				ad.	Pattern: Prairie A (9 light).
				ae.	Pattern: Prairie (6 light).
				af.	Pattern: Specified equal light.
			4.	Finelight™ Grilles: Provide contour profile aluminum muntin bars permanently mounted within insulating glass unit where indicated on Drawings.
				a.	Grille Intersections: ABS concealed plastic connectors with nylon end keepers.
	** NOTE TO SPECIFIER ** Delete surface finish not required. Specify if exterior color is different than interior color.
				b.	Exterior and Interior Surface Finish: White color painted finish.
				c.	Exterior and Interior Surface Finish: Sandtone color painted finish.
				d.	Exterior and Interior Surface Finish: Terratone color painted finish.
				e.	Exterior and Interior Surface Finish: Forest Green color painted finish.
	** NOTE TO SPECIFIER ** Below finishes available for Andersen® A-Series Windows only.
				f.	Exterior and Interior Surface Finish: Canvas color painted finish.
				g.	Exterior and Interior Surface Finish: Dove Gray color painted finish.
				h.	Exterior and Interior Surface Finish: Prairie Grass color painted finish.
				i.	Exterior and Interior Surface Finish: Red Rock color painted finish.
				j.	Exterior and Interior Surface Finish: Cocoa Bean color painted finish.
				k.	Exterior and Interior Surface Finish: Dark Bronze color painted finish.
				l.	Exterior and Interior Surface Finish: Black color painted finish.
	** NOTE TO SPECIFIER ** Delete width not required.
				m.	Width: 3/4 inch (19 mm).
				n.	Width: 1 inch (25 mm).
	** NOTE TO SPECIFIER ** Delete pattern not required.
				o.	Pattern: As indicated on Drawings.
				p.	Pattern: Colonial.
				q.	Pattern: Modified Colonial.
				r.	Pattern: Prairie A (9 light).
				s.	Pattern: Prairie (6 light).
				t.	Pattern: Specified equal light.
				u.	Pattern: Short fractional.
				v.	Pattern: Tall fractional.
				w.	Pattern: Custom.
	2.6	DOOR AND WINDOW JOINING SYSTEMS:
	** NOTE TO SPECIFIER ** Andersen windows strongly recommends consultation with an experienced structural engineer, architect, or contractor and a local Andersen representative when specifying Andersen joining systems. Consult an Andersen representative for joining options when joining Impact Resistant door products. ** NOTE TO SPECIFIER ** If required for project, retain one of the 1-way or 2-way combinations below and related subparagraph. Delete combinations not required for project.
		A.	LVL Reinforced Joining - 1-way Combination: Provide 4-9/16 inches (116 mm) by 3/4 inch (19 mm) laminated veneer lumber (LVL) joining with extruded anodized aluminum trim receptor end cap.
			1.	Provide corrosion resistant screws and bolts for fastening reinforcement members to wood frame and fastening end brackets to reinforcement members.
		B.	LVL Reinforced Joining - 1-way Combination: Provide 6-9/16 inches (167 mm) by 3/4 inch (19 mm) laminated veneer lumber (LVL) joining with extruded anodized aluminum trim receptor end caps.
			1.	Provide corrosion resistant screws and bolts for fastening reinforcement members to wood frame and fastening end brackets to reinforcement members.
		C.	LVL Reinforced Joining - 2-way Combination: Provide 4-9/16 inches (116 mm) by 3/4 inch (19 mm) laminated veneer lumber (LVL) joining with extruded anodized aluminum trim receptor end cap.
			1.	Provide corrosion resistant screws and bolts for fastening reinforcement members to wood frame and fastening end brackets to reinforcement members.
		D.	LVL Reinforced Joining - 2-way Combination: Provide 6-9/16 inches (167 mm) by 3/4 inch (19 mm) laminated veneer lumber (LVL) joining with extruded anodized aluminum trim receptor end caps.
			1.	Provide corrosion resistant screws and bolts for fastening reinforcement members to wood frame and fastening end brackets to reinforcement members.
		E.	Gusset Plates: Galvanized steel plates as recommended by door manufacturer for specific application.
		F.	Fasteners: Corrosion-resistant screws as provided by door manufacturer for fastening reinforcement members and gusset plates to wood frame. Other fasteners are provided by door installer.
		G.	Head Flashing: 6 inches (152 mm) long sheet vinyl.
			1.	Color: Match door exterior color.
		H.	Sealant: As recommended by door manufacturer.
		I.	Exterior Vinyl Trim Strips: Provide for each joining method used.
			1.	Color: Match door exterior color.
	PART 3	EXECUTION
	3.1	EXAMINATION
		A.	Site Verification of Conditions: Verify that site conditions are acceptable for installation of units, including the following:
			1.	Concrete surfaces are dry and free of excess mortar, rocks, sand, and other construction debris.
	** NOTE TO SPECIFIER ** Retain subparagraph below for masonry construction.
			2.	Masonry openings are square and dimensions are correct.
	** NOTE TO SPECIFIER ** Retain subparagraph below for wood framing.
			3.	Rough openings are square and dimensions are correct.
				a.	Sill plates are level.
				b.	Wood frame walls are dry, clean, sound, and well nailed or glued, free of voids and without offsets at joints.
				c.	Nail heads are driven flush with surfaces in openings and within 3 inches (75 mm) of rough opening.
		B.	Do not proceed with installation of units until unacceptable conditions are corrected.
		C.	If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
	3.2	PREPARATION
		A.	Clean surfaces thoroughly prior to installation.
		B.	Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
		C.	General:
			1.	Remove unit components, parts, accessories, and installation guides from carton.
			2.	Inspect unit components and verify that components are not damaged and that parts are included before disposing of carton.
	** NOTE TO SPECIFIER ** Delete if not required.
			3.	Field-assemble multiple units before installation in accordance with manufacturer's installation guide.
		D.	Interface With Other Work:
			1.	Perform installation in accordance with Manufacturer's instructions.
			2.	Install units level, plumb, square, true to line, without distortion, anchored securely in place to structural support, and in proper relation to wall flashing and other adjacent construction.
			3.	Separate aluminum and other corrodible surfaces from sources of corrosion or electrolytic action at points of contact with other materials.
			4.	Install insulation in shim space around unit perimeter to maintain continuity of building insulation. Do not overfill.
			5.	Hold back exterior siding or other finish materials from edge of unit to allow for expansion and contraction and installation of proper joint sealant with backing materials. Seal perimeter of unit after exterior finish is applied per requirements of Division 07 "Joint Sealants" Section.
			6.	Extend vapor barrier to interior face of unit frame and attach.
			7.	Finish interior units per requirements specified in related sections. Refer to, and comply with, additional requirements in manufacturer's installation guides.
			8.	Install optional hardware and unit accessories after cleaning.
		E.	Site Tolerances:
			1.	Adjust operation, insect screens, hardware, and accessories for a tight fit at contact points and weatherstripping for smooth operation and weather tight closure.
	** NOTE TO SPECIFIER ** Specify the final action required to clean installed equipment or other completed work to properly function or perform. Coordinate article below with Division 01 Execution Requirements (Cleaning) Section and specific project requirements.
	3.3	CLEANING
		A.	Clean units using cleaning material and methods specifically recommended by window manufacturer.
		B.	Remove excess sealants, glazing materials, dirt, and other substances.
		C.	Avoid damaging protective coatings and finishes.
		D.	Protect unit surfaces from masonry cleaning solution that could damage insulation glass panels or hardware.
		E.	Remove debris from work site and properly dispose of debris.
	** NOTE TO SPECIFIER ** Delete if not required.
	3.4	FIELD TESTING
	** NOTE TO SPECIFIER ** Coordinate article below with conditions of the contract and with division 01 quality control. Testing equipment shall be calibrated per Section 9 of ASTM E1105: Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors and Curtain Walls, by Uniform or Cyclic Static Air Pressure Difference, where the water test pressure shall be run at 2/3 (0.667) of the water test pressure used to achieve the products rated design pressure. The numbers of products tested shall be agreed and written in the project specification and shall not exceed 1 percent of the total number of openings unless specified otherwise.
		A.	General: Test units per the following procedures:
			1.	Inspect units and verify installation per Manufacturer's instructions.
			2.	For products installed less than 6 months, comply with AAMA 502-08 Voluntary Specification for Field Testing of Windows and Sliding Glass Doors, Procedure B.
			3.	For products installed longer than 6 months, comply with AAMA 511-08: Voluntary Guideline for Forensic Water Penetration Testing of Fenestration Products. If test indicates that field testing of units is necessary, test product as indicated in paragraph 1 above.
			4.	Do not proceed with installation of additional units until unacceptable conditions are corrected.
	3.5	PROTECTION
		A.	Protect installed products until completion of project.
		B.	Touch-up, repair or replace damaged products before Substantial Completion.
	END OF SECTION