MasterFormat: 95

SpecWizard: customize this spec    Download this Coating Systems For Concrete Floors Specification for   WORD | WP | RTF | TEXT

Find over 500 more construction specifications | Arcat.com

	SECTION 09670
	COATING SYSTEMS FOR CONCRETE FLOORS
	Copyright 2006 - 2006 ARCAT, Inc. - All rights reserved
	** NOTE TO SPECIFIER ** Tennant Company, Floor Coatings Div.; concrete floor coating and surfacing products. This section is based on the products of Tennant Company, Tennant Coatings Technologies, which is located at: 701 N. Lilac Dr., P. O. Box 1452 Minneapolis, MN 55440-1452 Toll Free: (800) 228-4943 Phone: (763) 208-9414 Fax: (763) 208-4875 Web Site: www.tennantfloorcoatings.com E-mail:architect@tennantco.com
	[ Click Here ] for additional information. Tennant Company is a manufacturer of floor cleaning machines, parts and accessories, as well as floor coatings. Founded in 1870, Tennant is headquartered in Minneapolis, Minnesota, and has manufacturing facilities in Holland, Michigan, and Uden, The Netherlands. Our products are marketed worldwide under the brand names Tennant, and Nobles. We sell and service products directly in eight countries and through distributors in 45 others. This specification includes concrete floor coating and resurfacing systems for warehousing and distribution, manufacturing, aviation, commercial, food and beverage, and institutional applications.
	PART 1	GENERAL
	1.1	SECTION INCLUDES
	** NOTE TO SPECIFIER ** Delete items below not required for project.
		A.	Resurfacers for concrete floors.
		B.	Primer system for concrete floors.
		C.	Epoxy coating systems for concrete floors.
		D.	Urethane coating systems for concrete floors.
		E.	Decorative coating systems for concrete floors.
		F.	UV cured coating systems for vinyl composition tile and concrete floors.
		G.	MMA (Methyl Methacrylate) coating systems for concrete floors.
	1.2	RELATED SECTIONS
	** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
		A.	Section 01400 - Quality Requirements: Testing and Inspection Services.
		B.	Section 02760 - Paving Specialties: Pavement marking paints.
		C.	Section 09900 - Sealant and Joint Fillers.
		D.	Section 09980 - Coatings for Concrete and Masonry.
	1.3	REFERENCES
	** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
		A.	ASTM C 307 - Standard Test Method for Tensile Strength of Chemical-Resistant Mortar, Grouts, and Monolithic Surfacing.
		B.	ASTM C 579 - Standard Test Methods for Compressive Strength of Chemical- Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes.
		C.	ASTM C 580 - Standard Test Method for Flexural Strength and Modulus of Elasticity of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes.
		D.	ASTM D 256 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance Of Plastics.
		E.	ASTM D 570 - Standard Test Method for Water Absorption of Plastics.
		F.	ASTM D 531 - Standard Test Method for Linear Shrinkage and Coefficient of Thermal Expansion of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes.
		G.	ASTM D 648 - Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position.
		H.	ASTM D 695 - Standard Test Method for Compressive Properties of Rigid Plastics.
		I.	ASTM D 696 - Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between - 30 Degrees C and 30 Degrees C with a Vitreous Silica Dilatometer.
		J.	ASTM D 1308 - Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes.
		K.	ASTM D 2047 - Standard Test Method for Static Coefficient of Friction of Polish-Coated Flooring Surfaces as Measured by the James Machine.
		L.	ASTM D 2134 - Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker.
		M.	ASTM D 2369 - Standard Test Method for Volatile Content of Coatings.
		N.	ASTM D 2370 - Standard Test Method for Tensile Properties of Organic Coatings.
		O.	ASTM D 3960 - Standard Practice for Determining Volatile Organic Compound (Voc) Content of Paints and Related Coatings.
		P.	ASTM D 4060 - Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser.
		Q.	ASTM F 1869 - Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride.
		R.	ASTM F 2170 - Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using In Situ Probes.
		S.	ASTM G 21 - Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi.
		T.	L.A. Rule 66 and VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** Delete product references from the list below that are not actually required by the text of the edited section.
	1.4	PERFORMANCE REQUIREMENTS
		A.	Moisture Vapor Reducer: Eco-MVR. A fluid-applied uniquely-modified epoxy based moisture mitigation system.
			1.	Adhesion psi: 100 percent failure in concrete exposed to MVER of 10 lbs for 7 mils and 15 lbs for 15 mils per ASTM F 1869-04: >400.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		B.	Power Trowel Epoxy: Eco-PT 250/Eco-PT Topcoat. A filled two-component, 100 percent solids epoxy for resurfacing interior concrete floors.
			1.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic), Ethylene Glycol (Antifreeze) and Jet Fuel (JP-4) with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		C.	Multi-Purpose Epoxy: Eco-MPE, multi-purpose, two-component, 100 percent solids epoxy.
			1.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic), Ethylene Glycol (Antifreeze) and Jet Fuel (JP-4) with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		D.	Rapid Cure Epoxy/M: Eco-RCE/M, moderately accelerated cure, two-component, 100 percent solids epoxy.
			1.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic), Ethylene Glycol (Antifreeze) and Jet Fuel (JP-4) with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		E.	Rapid Cure Epoxy/F: Eco-RCE/F, fully accelerated cure, two-component, 100 percent solids epoxy.
			1.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic), Ethylene Glycol (Antifreeze) and Jet Fuel (JP-4) with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		F.	Rapid Cure Epoxy: Eco-RCE, rapid cure, two-component, 100 percent solids epoxy.
			1.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic), Ethylene Glycol (Antifreeze) and Jet Fuel (JP-4) with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		G.	Colored Epoxy Primer: Eco-CEP, white, two-component, 100 percent solids epoxy.
			1.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic), Ethylene Glycol (Antifreeze) and Jet Fuel (JP-4) with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		H.	High Wear Epoxy: Eco-Shield, three-component, 100 percent solids epoxy.
			1.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Ethylene Glycol (Antifreeze) and Jet Fuel (JP-4) with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		I.	Chemical Resistant Epoxy: Eco-CRE, two-component novolac epoxy.
			1.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic), 10 percent Nitric Acid, Jet Fuel (JP-4), Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7 day spot testing on concrete.
		J.	Cementitious Trowel Overlay: Eco-CTO. A three-component water- based cementitious-polyurethane for resurfacing interior concrete floors requiring thermal shock resistance.
			1.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to 50 percent sodium hydroxide with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		K.	Cementitious Workable Overlay: Eco-CWO. A three-component water- based cementitious-polyurethane for resurfacing interior concrete floors requiring thermal shock resistance.
			1.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to 50 percent sodium hydroxide with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		L.	Cementitious Flowable Overlay: Eco-CFO, a three-component cementitious-polyurethane slurry with aggregate broadcast for resurfacing interior concrete floors requiring thermal shock resistance.
			1.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and 37 percent sulfuric acid and excellent chemical resistance to 50 percent sodium hydroxide with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		M.	Cementitious Vertical Overlay: Eco-CVO. A three-component water- based cementitious-polyurethane for protecting vertical surfaces.
			1.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to 50 percent sodium hydroxide with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		N.	Satin Urethane Topcoat: Eco-HTS 100, 100 g/L reduced VOC, low odor, three-component, moisture cured, aliphatic urethane applied over Tennant 100 percent solids epoxy.
			1.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to Jet Fuel (JP-4), Xylene, Brake Fluid, Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with all current U.S. VOC/VOS Rules and Regulations.
		O.	Gloss Urethane Topcoat: Eco-HPS 100, 100 g/L reduced VOC, low odor, two component aliphatic, moisture cured urethane topcoat applied over Tennant 100 percent solids epoxy.
			1.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to Jet Fuel (JP-4), Xylene, Brake Fluid, Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with all current U.S. VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** The following product may not meet VOC requirements in some locations. Contact the manufacturer for additional information.
		P.	Gloss Urethane Topcoat: WEARGUARD-ITS, one component, moisture cured urethane topcoat.
			1.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Jet Fuel with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** The following product may not meet VOC requirements in some locations. Contact the manufacturer for additional information.
		Q.	Gloss Urethane Topcoat: WEARGUARD -CRU, two component, aliphatic, chemical resistant urethane coating.
			1.	Chemical Resistance: Excellent chemical resistance to Ethylene Glycol (Antifreeze), JP-4 and Jet A1 Jet Fuel, Brake Fluid, Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7-day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		R.	InstaCure+: Eco-UVC, two-component, UV cured coating for application over VCT, sheet vinyl and concrete or over previously coated aliphatic urethanes. Eco-UVC may also be suitable for other surfaces such as linoleum, mamoleum and terrazzo. Cures instantly with UV light machine application.
			1.	Chemical Resistance: Excellent chemical resistance to hand sanitizers, 10 percent hydrochloric acid and jet fuel with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		S.	InstaCure: Eco-UVS, three-component, UV cured coating for application over concrete or VCT, Quarry or unglazed ceramic tile or over previously coated epoxies or aliphatic urethanes. Cures instantly with UV light machine application.
			1.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Jet Fuel with no adverse effects, based on 7 day spot testing on concrete.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** Contact the manufacturer for a full list of 1 day and 7 day chemical resistance testing results.
		T.	Eco-DFS: Decorative Flake System with Eco-TCU Topcoat.
			1.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, ethylene glycol (Antifreeze), JP-4 and Jet A1 Jet Fuel, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
	** NOTE TO SPECIFIER ** Contact the manufacturer for a full list of 1 day and 7 day chemical resistance testing results.
		U.	Eco-DFS: Decorative Flake System with Eco-URE Topcoat.
			1.	Chemical Resistance: Excellent chemical resistance to JP-4 and Jet A1 Jet Fuel, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete. Good chemical resistance to acids and alkalis, and ethylene glycol (Antifreeze).
	** NOTE TO SPECIFIER ** Contact the manufacturer for a full list of 1 day and 7 day chemical resistance testing results.
		V.	Eco-DQS: Decorative Quartz System with Eco-TCU Topcoat.
			1.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, ethylene glycol (Antifreeze), JP-4 and Jet A1 Jet Fuel, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
			2.	Slip resistant as certified by the National Floor Safety Institute.
		W.	Eco-DQS: Decorative Quartz System with Eco-URE Topcoat.
			1.	Chemical Resistance: Excellent chemical resistance to JP-4 and Jet A1 Jet Fuel, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete. Good chemical resistance to acids and alkalis, and ethylene glycol (Antifreeze).
		X.	Eco-EDE: Electrostatic Dissipative Epoxy
			1.	Electrical Properties: Surface resistance at 100V: 1.0 x 105 - <1.0 x 109.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		Y.	Eco-ECT: Electrostatic Control Epoxy.
			1.	Electrical Properties: Surface resistance-point to point / point to ground. 1.0 x 105 - <1.0 x 106 with the Eco-ECP primer. 1.0 x 105 - <1.0 x 109 with the Eco-EDP primer.
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** The following product may not meet VOC requirements in some locations. Contact the manufacturer for additional information.
		Z.	Eco-ECP: Electrostatic Conductive Primer.
			1.	Percent Solids A/B combined, 77.06 percent
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		AA.	Eco-EDP: Electrostatic Dissipative Primer.
			1.	Percent Solids A/B combined, 90.95 percent
			2.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		AB.	MM (Methyl Methacrylate) Coating System:
			1.	MMA Primer.
				a.	Percent Solids 100 percent.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
			2.	MMA Body Coat.
				a.	Percent Solids 100 percent.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
			3.	MMA Clear Topcoat.
				a.	Percent Solids 100 percent.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
	1.5	SUBMITTALS
		A.	Submit under provisions of Section 01300.
		B.	Product Data: Manufacturer's data sheets on each product to be used, including:
			1.	Preparation instructions and recommendations.
			2.	Storage and handling requirements and recommendations.
			3.	Installation methods.
	** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.
		C.	Selection Samples: For each finish product specified, two complete sets of color charts representing manufacturer's full range of available colors.
		D.	Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.
		E.	Manufacturer's Certificates: Certify products meet or exceed specified requirements.
	1.6	QUALITY ASSURANCE
		A.	Installer Qualifications: Submit list of a minimum of five completed projects of similar size and complexity to this Work. Include for each project:
			1.	Project name and location.
			2.	Name of owner.
			3.	Name of contractor.
			4.	Name of architect.
			5.	Name of coating manufacturer.
			6.	Approximate area of coatings applied.
			7.	Date of completion.
	** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.
		B.	Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.
			1.	Finish areas designated by Architect.
			2.	Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.
			3.	Refinish mock-up area as required to produce acceptable work.
		C.	Pre-Application Meeting: Convene a pre-application meeting two weeks before the start of application of floor coating system. Require attendance of parties directly affecting work of this section, including the Contractor, Applicator and Manufacturer's Representative. Review the surface preparation, application, cleaning, protection and coordination with other work.
	1.7	DELIVERY, STORAGE, AND HANDLING
		A.	Delivery: Deliver materials to site in manufacturer's original, unopened containers and packaging, with labels clearly identifying product name and manufacturer.
		B.	Store materials in accordance with the manufacturers instructions.
			1.	Store materials in dry, enclosed area with adequate protection from moisture.
			2.	Keep containers sealed until ready for use.
			3.	Storage Temperature: 65 degrees F (18 degrees C) and 90 degrees F (32 degrees C).
		C.	Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.
	1.8	PROJECT CONDITIONS
		A.	Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.
		B.	Provide ventilation during coating evaporation stage in confined or enclosed areas in accordance with manufacturer's instructions.
		C.	Schedule coating work to avoid excessive dust and airborne contaminants. Protect work areas from excessive dust and airborne contaminants during coating application and curing.
	1.9	COORDINATION
		A.	Coordinate Work with other operations and installation of floor finish materials to avoid damage to installed materials.
	PART 2	PRODUCTS
	2.1	MANUFACTURERS
		A.	Acceptable Manufacturer: Tennant Company, Tennant Coatings Technologies, 701 N. Lilac Dr., P. O. Box 1452, Minneapolis, MN 55440-1452. ASD. Toll Free: (800) 228-4943. Phone: (763) 208-9414. Fax: (763) 208-4875. Web Site: www.tennantfloorcoatings.com E-mail: architect@tennantco.com.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
		B.	Substitutions: Not permitted.
		C.	Requests for substitutions will be considered in accordance with provisions of Section 01600.
	2.2	APPLICATION
	** NOTE TO SPECIFIER ** The following products are suitable for Factories, Assembly Lines, Loading Docks, Machine Shops. Abrasion resistance and slip and fall prevention are required for these abusive, punishing environments. Select the products required and delete those not required. Coordinate the product selected here with the Product Specifications in successive paragraphs.
		A.	Manufacturing Facility Systems:
			1.	Power Trowel Epoxy: Eco-PT 250/Eco-PT Topcoat. A filled two-component, two-component, 100 percent solids epoxy for resurfacing interior concrete floors.
				a.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic), Ethylene Glycol (Antifreeze) and Jet Fuel (JP-4) with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** The following product may not meet VOC requirements in some locations. Contact the manufacturer for additional information.
			2.	Gloss Urethane Topcoat: WEARGUARD-ITS, one component, moisture cured urethane topcoat.
				a.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Jet Fuel with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
			3.	Satin Urethane Topcoat: Eco-HTS 100, 100 g/L reduced VOC, low odor, three-component, moisture cured, aliphatic urethane applied over Tennant 100 percent solids epoxy. Application over prime coat required.
				a.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to Jet Fuel (JP-4), Xylene, Brake Fluid, Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with all current U.S. VOC/VOS Rules and Regulations.
			4.	Gloss Urethane Topcoat: Eco-HPS 100, 100 g/L reduced VOC, low odor, two-component aliphatic, moisture cured urethane topcoat over Tennant 100 percent solids epoxy. Application over prime coat required.
				a.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to Jet Fuel (JP-4), Xylene, Brake Fluid, Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with all current U.S. VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** The following product is part of a coating system. The system requires a prime coat of Eco-MPE followed by an intermediate coat of Eco-EDP.
			5.	Electrostatic Dissipative Epoxy: Eco-EDE, three-component 100 percent solids epoxy. Part of a coating system with Eco-MPE primer and Eco-EDP intermediate coat.
				a.	Electrical Properties: Surface resistance, 100V. 1.0 x 105 - <1.0 x 106.
				b.	Complies with all current U.S. VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** The following product is part of a coating system. The system requires a prime coat of Eco-MPE followed by an intermediate coat of either Eco-ECP, for a conductive floor, or Eco-EDP for a dissipative floor.
			6.	Electrostatic Control Epoxy: Eco-ECT, two-component 100 percent solids epoxy. Part of a coating system with Eco-MPE primer and Eco-ECP intermediate coat.
				a.	Electrical Properties: Surface resistance-point to point / point to ground. 1.0 x 105 - <1.0 x 106 with Eco-ECP . 1.0 x 105 - <1.0 x 109 with Eco-EDP.
				b.	Complies with all current U.S. VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** The following product is a high gloss surface that is jet fuel, Skydrol and industrial chemical resistant, slip resistant, easy to clean and durable coating are very suitable for image conscious aviation facilities. Select the products required and delete those not required Coordinate the product selected here with the Product Specifications in successive paragraphs.
		B.	Aviation Facility Systems:
	** NOTE TO SPECIFIER ** The following product may not meet VOC requirements in some locations. Contact the manufacturer for additional information.
			1.	WEARGUARD-CRU Hanger Floor Solution: Epoxy Prime coat with Wearguard-CRU, two component, chemical and UV resistant gloss urethane coating. Application over prime coat required.
				a.	Chemical Resistance: Excellent chemical resistance to Ethylene Glycol (Antifreeze), JP-4 and Jet A1 Jet Fuel, Brake Fluid, Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7-day spot testing on concrete.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
			2.	Satin Urethane Topcoat: Eco-HTS 100, 100 g/L reduced VOC, low odor, three-component, moisture cured, aliphatic urethane applied over Tennant 100 percent solids epoxy. Application over prime coat required.
				a.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to Jet Fuel (JP-4), Xylene, Brake Fluid, Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with all current U.S. VOC/VOS Rules and Regulations.
			3.	Gloss Urethane Topcoat: Eco-HPS 100, 100 g/L reduced VOC, low odor, two-component aliphatic, moisture cured urethane topcoat over Tennant 100 percent solids epoxy. Application over prime coat required.
				a.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to Jet Fuel (JP-4), Xylene, Brake Fluid, Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with all current U.S. VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** The following products are suitable for auto dealerships, retail outlets, sporting facilities, airport concourses, and hotel lobbies that require attractive, durable and slip resistant coatings. Contact the manufacturer for a full list of 1 day and 7 day chemical resistance testing results. Select the products required and delete those not required. Coordinate the product selected here with the Product Specifications in successive paragraphs.
		C.	Commercial Facility Systems:
			1.	Eco-DFS - Decorative Flake System.
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, ethylene glycol (Antifreeze), JP-4 and Jet A1 Jet Fuel, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
			2.	Eco-DQS: Decorative Quartz System.
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, ethylene glycol (Antifreeze), JP-4 and Jet A1 Jet Fuel, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
				b.	Slip resistant as certified by the National Floor Safety Institute.
			3.	Tennant MMA Broadcast Slurry System.
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, animal fats, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
				b.	Percent active resin: 100 percent solids. Complies with SCAQMD VOC Regulations.
			4.	Tennant MMA Double Broadcast System.
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, animal fats, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
				b.	Percent active resin: 100 percent solids. Complies with SCAQMD VOC Regulations.
	** NOTE TO SPECIFIER ** The following products are suitable for Pharmaceutical, Food and Beverage facilities, that require bacterial and thermal resistant, and durable coatings. Select the products required and delete those not required. Coordinate the product selected here with the Product Specifications in successive paragraphs.
		D.	Pharmaceutical, Food and Beverage Facility Systems:
			1.	Cementitious Trowel Overlay: Eco-CTO, Cementitious Trowel Overlay. A three-component water- based cementitious-polyurethane for resurfacing interior concrete floors requiring thermal shock resistance.
				a.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to 50 percent sodium hydroxide with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
			2.	Cementitious Workable Overlay: Eco-CWO, Cementitious Workable Overlay. A three-component water- based cementitious-polyurethane for resurfacing interior concrete floors requiring thermal shock resistance.
				a.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to 50 percent sodium hydroxide with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
			3.	Cementitious Flowable Overlay: Eco-CFO, a three-component cementitious-polyurethane slurry with aggregate broadcast for resurfacing interior concrete floors requiring thermal shock resistance.
				a.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and 37 percent sulfuric acid and excellent chemical resistance to 50 percent sodium hydroxide with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
			4.	Cementitious Vertical Overlay: Eco-CVO, Cementitious Vertical Overlay. A three-component water- based cementitious-polyurethane for protecting vertical surfaces.
				a.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to 50 percent sodium hydroxide with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
			5.	Eco-DQS: Decorative Quartz System:
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, ethylene glycol (Antifreeze), JP-4 and Jet A1 Jet Fuel, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
				b.	Slip resistant as certified by the National Floor Safety Institute.
			6.	Tennant MMA Broadcast Slurry System.
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, animal fats, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
				b.	Percent active resin: 100 percent solids. Complies with SCAQMD VOC Regulations.
			7.	Tennant MMA Double Broadcast System.
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, animal fats, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
				b.	Percent active resin: 100 percent solids. Complies with SCAQMD VOC Regulations.
	** NOTE TO SPECIFIER ** The following products are suitable for schools, hospitals, prisons, kitchens and sports facilities that require bacterial resistant, attractive, durable and slip resistant coatings. Contact the manufacturer for a full list of 1 day and 7 day chemical resistance testing results. Select the products required and delete those not required. Coordinate the product selected here with the Product Specifications in successive paragraphs.
		E.	Institutional Facility Systems
			1.	Eco-DFS - Decorative Flake System
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, ethylene glycol (Antifreeze), JP-4 and Jet A1 Jet Fuel, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
			2.	Eco-DQS: Decorative Quartz System
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, ethylene glycol (Antifreeze), JP-4 and Jet A1 Jet Fuel, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
				b.	Slip resistant as certified by the National Floor Safety Institute.
			3.	Tennant MMA Broadcast Slurry System.
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, animal fats, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
				b.	Percent active resin: 100 percent solids. Complies with SCAQMD VOC Regulations.
			4.	Tennant MMA Double Broadcast System.
				a.	Chemical Resistance: Excellent chemical resistance to acids and alkalis, animal fats, motor oils and bleach with no adverse effects, based on 1-day spot testing on concrete.
				b.	Percent active resin: 100 percent solids. Complies with SCAQMD VOC Regulations.
			5.	InstaCure+: Eco-UVC. two-component, UV cured coating.
				a.	Chemical Resistance: Excellent chemical resistance to hand sanitizers, 10 percent hydrochloric acid and jet fuel with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with SCAQMD VOC Regulations.
			6.	InstaCure: Eco-UVS. three-component, UV cured coating.
				a.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Jet Fuel with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with SCAQMD VOC Regulations.
	** NOTE TO SPECIFIER ** The following products are suitable for Loading Docks, Main Traffic Aisles, Storage Areas. High traffic areas demand high-wear solutions suitable for heavy wheeled traffic. Select the products required and delete those not required. Coordinate the product selected here with the Product Specifications in successive paragraphs.
		F.	Warehousing And Distribution Systems:
			1.	Satin Urethane Topcoat: Eco-HTS 100, 100 g/L reduced VOC, low odor, three-component, moisture cured, aliphatic urethane applied over Tennant 100 percent solids epoxy. Application over prime coat required.
				a.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to Jet Fuel (JP-4), Xylene, Brake Fluid, Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with all current U.S. VOC/VOS Rules and Regulations.
			2.	Gloss Urethane Topcoat: Eco-HPS 100, 100 g/L reduced VOC, low odor, two-component aliphatic, moisture cured urethane topcoat over Tennant 100 percent solids epoxy. Application over prime coat required.
				a.	Chemical Resistance: Excellent chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Lactic acid and excellent chemical resistance to Jet Fuel (JP-4), Xylene, Brake Fluid, Skydrol 500B and Skydrol LD4 with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with all current U.S. VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** The following product may not meet VOC requirements in some locations. Contact the manufacturer for additional information.
			3.	Gloss Urethane Topcoat: WEARGUARD -ITS, one component, moisture cured urethane topcoat. Application over prime coat required.
				a.	Chemical Resistance: Good chemical resistance to 30 percent Hydrochloric Acid (Muriatic) and Jet Fuel with no adverse effects, based on 7 day spot testing on concrete.
				b.	Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
	** NOTE TO SPECIFIER ** The following product specifications are grouped by product types. Select the products required and delete those not required. Coordinate the product selected here with the Applications specified above.
	2.3	RESURFACERS
	** NOTE TO SPECIFIER ** Eco-PT™ 250 is a filled two-component, 100 percent solids epoxy for resurfacing interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		A.	Epoxy Overlay Resurfacer: Eco-PT 250, Power Trowel Epoxy, a filled two-component, 100 percent solids epoxy.
			1.	Properties:
				a.	Percent Solids, ASTM D 2369:
					1)	Part A - 100 percent.
					2)	Part B - 100 percent.
					3)	Part C - 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D3960: 0 lb/gal or 0 g/L
				c.	Coefficient of Thermal Linear Expansion, ASTM D 696: 1.97 x 10-5 mm/mm/ degrees C.
				d.	Compressive Strength, ASTM C 579: 10,000 psi (69,000 kPA).
				e.	Flexural Strength, ASTM C 580: 3,700 psi (25,530 kPA).
				f.	Heat Deflection Temperature, ASTM D 648:
					1)	60 degrees C @ 264 psi load.
					2)	66 degrees C @ 66 psi load.
				g.	Izod Impact Strength, ASTM D 256: 0.26 lb/in or 45.53 (N/m).
				h.	Tensile Strength, ASTM C 307: 1,690 psi or 11,661 kPa.
	** NOTE TO SPECIFIER ** Eco-CTO™ a three-component water-based cementitious-polyurethane for resurfacing interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		B.	Cementitious Trowel Overlay: Eco-CTO, Cementitious Troweled Overlay, a three-component water-based cementitious-polyurethane.
			1.	Properties:
				a.	Volatile Organic Compound (VOC), ASTM D 3960: 0 lb/gal (0 g/L).
				b.	Tensile Strength, ASTM C 307: 700 psi (4,826 kPa).
				c.	Percent Solids, ASTM D 2369:
					1)	Part A - 67.49 percent.
					2)	Part B - 100 percent.
					3)	Part C - 100 percent.
				d.	Coefficient of Linear Thermal Expansion, ASTM C 531: 1.71 x 10-5 mm/mm/ degrees F.
				e.	Compressive Strength, ASTM C 579: 7,500-8,500 psi (52-59 MPA).
				f.	Flexural Strength, ASTM C 580: 1,700 psi (10,342 kPA).
				g.	Flexural Modulas, ASTM C 580: 617,000 psi (4,254 MPa).
	** NOTE TO SPECIFIER ** Select color required. Delete those not required.
			2.	Colors: Available only in the following colors:
				a.	Red.
				b.	Beige.
				c.	Light Gray. Beige mixed with 1.5 oz Canada Gray colorant per bag.
				d.	Dark Gray. Beige mixed with 1.5 oz Battleship Gray colorant per bag.
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			3.	Traction Grit: Silica Sand.
	** NOTE TO SPECIFIER ** Cove is optional, select if required and delete if not required.
			4.	Optional Cove:
				a.	Cove Primer: Eco-CVP, Cementitious Vertical Primer. A two-component primer for use with Eco-CVO.
				b.	Cove: Eco-CVO, Cementitious Vertical Overlay. A three- component, water-based cementitious-polyurethane.
		C.	Cementitious Workable Overlay: Eco-CWO, Cementitious Workable Overlay, a three-component water-based cementitious-polyurethane.
			1.	Properties:
				a.	Volatile Organic Compound (VOC), ASTM D 3960: 0 lb/gal (0 g/L).
				b.	Tensile Strength, ASTM C 307: 700 psi (4,826 kPa).
				c.	Percent Solids, ASTM D 2369:
					1)	Part A - 67.49 percent.
					2)	Part B - 100 percent.
					3)	Part C - 100 percent.
				d.	Coefficient of Linear Thermal Expansion, ASTM C 531: 1.71 x 10-5 mm/mm/ degrees F.
				e.	Compressive Strength, ASTM C 579: 7,500-8,500 psi (52-59 MPA).
				f.	Flexural Strength, ASTM C 580: 1,700 psi (10,342 kPA).
				g.	Flexural Modulas, ASTM C 580: 617,000 psi (4,254 MPa).
	** NOTE TO SPECIFIER ** Select color required. Delete those not required.
			2.	Colors: Available only in the following colors:
				a.	Red.
				b.	Beige.
				c.	Light Gray. Beige mixed with 1.5 oz Canada Gray colorant per bag.
				d.	Dark Gray. Beige mixed with 1.5 oz Battleship Gray colorant per bag.
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			3.	Traction Grit: Silica Sand.
	** NOTE TO SPECIFIER ** Cove is optional, select if required and delete if not required.
			4.	Optional Cove:
				a.	Cove Primer: Eco-CVP, Cementitious Vertical Primer. A two-component primer for use with Eco-CVO.
				b.	Cove: Eco-CVO, Cementitious Vertical Overlay. A three- component, water-based cementitious-polyurethane.
	** NOTE TO SPECIFIER ** Eco-CFO™ a three-component cementitious-polyurethane for resurfacing interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		D.	Cementitious Flowable Overlay: Eco-CFO, Cementitious Flowable Overlay. A three-component water- based cementitious-polyurethane slurry with aggregate broadcast for resurfacing interior concrete floors.
			1.	Properties:
				a.	Volatile Organic Compound (VOC), ASTM D 3960: 0 lb/gal (0 g/L).
				b.	Tensile Strength, ASTM C 307: 700 psi (4,826 kPa).
				c.	Percent Solids, ASTM D 2369:
					1)	Part A - 67.49 percent.
					2)	Part B - 100 percent
					3)	Part C - 100 percent.
				d.	Coefficient of Linear Thermal Expansion, ASTM C 531: 1.71 x 10-5 mm/mm/ degrees F.
				e.	Compressive Strength, ASTM C 579: 8,500 psi (59 MPA).
				f.	Flexural Strength, ASTM C 580: 1,500 psi (10,342 kPA).
				g.	Flexural Modulas, ASTM C 580: 617,000 psi (4,254 MPa).
	** NOTE TO SPECIFIER ** Select color required. Delete those not required.
			2.	Colors: Available only in the following colors:
				a.	Red.
				b.	Beige.
				c.	Light Gray. Beige mixed with 1.5 oz Canada Gray colorant per bag.
				d.	Dark Gray. Beige mixed with 1.5 oz Battleship Gray colorant per bag.
	** NOTE TO SPECIFIER ** Decorative Traction Material and Traction grit is optional, select one of the following two paragraphs if required. Delete both if not required. A seal coat of Eco-CRE™ is recommended over the traction broadcast but is not required.
			3.	Traction Grit: Silica Sand.
			4.	Decorative Traction Material: Tennant Colored Quartz.
			5.	Optional Cove:
	** NOTE TO SPECIFIER ** Select cove required. Delete those not required.
				a.	Cove Primer: Eco-CVP, Cementitious Vertical Primer. A two-component primer for use with Eco-CVO.
				b.	Cove: Eco-CVO, Cementitious Vertical Overlay. A three- component, water-based cementitious-polyurethane.
	2.4	MOISTURE MITIGATION COATING
	** NOTE TO SPECIFIER ** Eco-MVR™ is applied either at 7 mils in one coat or 15 mils in two coats depending on factors such as moisture test results and age of the concrete. Call Tennant technical support for details and select system required.
		A.	Moisture Vapor Reducer: Eco-MVR, fluid-applied uniquely-modified epoxy.
			1.	System:
				a.	7 mils in one coat.
				b.	15 mils in two coats.
			2.	Properties:
				a.	Volatile Organic Compound (VOC), ASTM D 3960; .02 lb/gal or 2 g/L.
				b.	Alkali Resistance, ASTM D 1308; Resistant.
				c.	Microbial Resistance, ASTM G 21; Passes.
	2.5	PRIMER COATINGS
	** NOTE TO SPECIFIER ** Eco-MPE™ is a multi-purpose, two-component, 100 percent solids epoxy for protecting interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		A.	Multi-Purpose Epoxy: Eco-MPE, multi-purpose, two-component, 100 percent solids epoxy.
			1.	Properties:
				a.	Volatile Organic Compound (VOC), ASTM D 3960; 0 lb/gal or 0 g/L.
				b.	Tensile Strength, ASTM D 2370; 8,000 psi or 55,200 kPa.
				c.	Percent Elongation, ASTM D 2370; 5 percent.
	** NOTE TO SPECIFIER ** Select colorant if required. Delete if not required.
			2.	Colorant:
				a.	Battleship Gray.
				b.	Tile Red.
				c.	Smoke Blue.
				d.	Ivy Green.
				e.	Medium Gray.
				f.	Canada Gray.
				g.	Regal Blue.
				h.	Sandy Beige.
				i.	Black.
	** NOTE TO SPECIFIER ** Eco-RCE/M and Eco-RCE/F™ are fast cure (12 hour) high performance, two-component, 100 percent solids epoxies for protecting interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		B.	Rapid Cure Epoxy/M: Eco-RCE/M, moderately accelerated cure, two-component, 100 percent solids epoxy.
			1.	Properties:
				a.	Volatile Organic Compound (VOC), ASTM D 3960; 0 lb/gal or 0 g/L.
				b.	Tensile Strength, ASTM D 2370; 5,200 psi (35,880 kPa).
				c.	Percent Elongation, ASTM D 2370; 4 percent.
			2.	Colorant: Use only 100 series colorants in this epoxy
				a.	Black 100g/l
				b.	White 100g/l
				c.	Light Gray 100g/l
				d.	Canada Gray 100g/l
				e.	Medium Gray 100 g/l
				f.	Yellow 100 g/l
		C.	Rapid Cure Epoxy/F: Eco-RCE/F, fully accelerated cure, two-component, 100 percent solids epoxy.
			1.	Properties:
				a.	Volatile Organic Compound (VOC), ASTM D 3960; 0 lb/gal or 0 g/L.
				b.	Tensile Strength, ASTM D 2370; 5,200 psi (35,880 kPa).
				c.	Percent Elongation, ASTM D 2370; 4 percent.
			2.	Colorant: Use only 100 series colorants in this epoxy.
				a.	Black 100g/l
				b.	White 100g/l
				c.	Light Gray 100g/l
				d.	Canada Gray 100g/l
				e.	Medium Gray 100 g/l
				f.	Yellow 100 g/l
	** NOTE TO SPECIFIER ** Rapid Cure Epoxy: Eco-RCE™ is a fast set, two-component, 100 percent solids epoxy. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		D.	Rapid Cure Epoxy: Eco-RCE, fast set, two-component, 100 percent solids epoxy.
			1.	Properties:
				a.	Volatile Organic Compound (VOC), ASTM D 3960; 0 lb/gal or 0 g/L.
				b.	Tensile Strength, ASTM D 2370; 5,200 psi (35,880 kPa).
				c.	Percent Elongation, ASTM D 2370; 4 percent.
	** NOTE TO SPECIFIER ** Eco-CEP(tm) is a two-component, white, 100 percent solids epoxy for white and light gray topcoat application with excellent hiding properties. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		E.	Multi-Purpose Epoxy: Eco-CEP, multi-purpose, two-component, 100 percent solids epoxy.
			1.	Properties:
				a.	Volatile Organic Compound (VOC), ASTM D 3960; 0.07 lb/gal or 9 g/L.
				b.	Compressive Strength, ASTM D 695; 13,500 psi or 93,100 kPa.
				c.	Abrasion Resistance, ASTM D 4060; 120-135.
	** NOTE TO SPECIFIER ** Eco-CEP can be tinted to match gray topcoats. Call Tennant technical support for details.
			2.	Color: White.
	2.6	EPOXY COATINGS
	** NOTE TO SPECIFIER ** Eco-CRE™ is a chemical resistant, two-component, 100 percent solids epoxy for interior concrete floors.
		A.	Chemical Resistant Epoxy: Eco-CRE, two-component epoxy.
			1.	Percent Solids, ASTM D 2369:
				a.	Part A - 100 percent.
				b.	Part B - 100 percent.
			2.	Volatile Organic Compound (VOC), ASTM D 3960: 1. 0 lb/gal or 0 g/L.
			3.	Tensile Strength, ASTM D 2370: 8,000 psi or 55,200 kPa.
			4.	Percent Elongation, ASTM D 2370: 1.5 percent.
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			5.	Traction Grit: Tennant 291 Grit (60 mesh) - white aluminum oxide.
		B.	High Wear Epoxy: Eco-Shield:
			1.	Percent Solids, ASTM D 2369:
				a.	Part A - 94.35 percent.
				b.	Part B - 99.82 percent.
				c.	Part C - 100 percent.
			2.	Volatile Organic Compound (VOC), ASTM D 3960: 0. 41 lb/gal or 50 g/L.
			3.	Tensile Strength, ASTM D 2370: 8,000 psi or 55,200 kPa.
			4.	Percent Elongation, ASTM D 2370: 5 percent.
	** NOTE TO SPECIFIER ** Select colorant if required. Delete if not required.
			5.	Colorant:
				a.	Battleship Gray.
				b.	Tile Red.
				c.	Smoke Blue.
				d.	Ivy Green.
				e.	Medium Gray.
				f.	Canada Gray.
				g.	Regal Blue.
				h.	Sandy Beige.
				i.	Black.
				j.	Rotunda Red.
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			6.	Traction Grit: Tennant 291 Grit (60 mesh) - white aluminum oxide.
	2.7	ESD COATINGS
		A.	Electrostatic Conductive Primer: Eco-ECP, two-component epoxy.
			1.	Percent Solids, ASTM D 2369:
				a.	Part A - 70.61 percent.
				b.	Part B - 100 percent.
			2.	Volatile Organic Compound (VOC), ASTM D 3960, 2.05 lb/gal or 246 g/L.
		B.	Electrostatic Dissipative Primer: Eco-EDP, two-component epoxy.
			1.	Percent Solids, ASTM D 2369:
				a.	Part A - 87.74 percent.
				b.	Part B - 99.91 percent.
			2.	Volatile Organic Compound (VOC), ASTM D 3960, 0.82 lb/gal or 99 g/L.
		C.	Electrostatic Dissipative Epoxy: Eco-EDE, three-component epoxy.
			1.	Percent Solids, ASTM D 2369:
				a.	Part A – 99.36
				b.	Part B - 100
				c.	Part C – 100
			2.	Volatile Organic Compound (VOC), ASTM D 3960, 0.04 lb/gal or 5 g/L.
			3.	Tensile Strength, ASTM D 2370: 8,000 psi or 55,200 kPa.
			4.	Compressive Strength, ASTM D 695: 13,500 pi.
			5.	Colorant:
	** NOTE TO SPECIFIER ** Select colorant if required. Delete if not required.
				a.	Black.
				b.	Canada Gray.
				c.	Medium Gray.
				d.	Battleship Gray.
				e.	Sandy Beige.
				f.	Yellow.
				g.	Tile Red.
				h.	Rotunda Red.
				i.	Ivy Green.
				j.	Smoke Blue.
				k.	Regal Blue.
				l.	Canada Gray 100.
				m.	Medium Gray 100.
		D.	Electrostatic Control Epoxy: Eco-ECT, two-component epoxy.
			1.	Percent Solids, ASTM D 2369:
				a.	Part A - 98.29 percent.
				b.	Part B - 99.81 percent.
			2.	Volatile Organic Compound (VOC), ASTM D 3960, 0.11 lb/gal or 13 g/L.
			3.	Tensile Strength, ASTM D 2370: 8,000 psi or 55,200 kPa.
			4.	Percent Elongation, ASTM D 2370: 5 percent.
	** NOTE TO SPECIFIER ** Select colorant if required. Delete if not required.
			5.	Colorant:
				a.	Canada Gray 100.
				b.	Tile Red.
				c.	Sandy Beige.
	2.8	URETHANE COATINGS
	** NOTE TO SPECIFIER ** Eco-HTS 100(tm) is a reduced VOC, low odor, three-component, moisture cured urethane for interior concrete floors.
		A.	Satin Urethane Topcoat: Eco-HTS 100, 100 g/L reduced VOC, low odor, three-component, moisture cured, aliphatic urethane.
			1.	Percent Solids, ASTM D 2369:
				a.	Part A - 99.35 percent.
				b.	Part B - 59.23 percent.
				c.	Part C - 100 percent.
				d.	Mixed - 94 percent.
			2.	Volatile Organic Compound (VOC), ASTM D 3960: 0.71 lb/gal or 86 g/L.
			3.	Abrasion Resistance, ASTM D 4060: 18.0 mg loss, CS-17 wheel, 1000 gram load, 1000 revolutions.
			4.	Tensile Strength, ASTM D 2370: 6,250 psi or 43,088 kPa.
			5.	Percent Elongation, ASTM D 2370: 6 percent.
			6.	Konig Hardness, 171.3 (3 mil film).
	** NOTE TO SPECIFIER ** Select colorant if required. Delete if not required.
			7.	Colorant:
				a.	Black.
				b.	White.
				c.	Light Gray.
				d.	Canada Gray.
				e.	Medium Gray.
				f.	Battleship Gray.
				g.	Sandy Beige.
				h.	Yellow.
				i.	Tile Red.
				j.	Rotunda Red.
				k.	Ivy Green.
				l.	Smoke Blue.
				m.	Regal Blue.
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			8.	Traction Grit:
				a.	Tennant 291 Grit (60 mesh) - white aluminum oxide.
	** NOTE TO SPECIFIER ** Eco-HPS 100(tm), 100 g/L reduced VOC, low odor, two-component aliphatic, moisture cured urethane topcoat for interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		B.	Gloss Urethane Topcoat: Eco-HPS 100, 100 g/L reduced VOC, low odor, two-component aliphatic, moisture cured urethane topcoat.
			1.	Percent Solids, ASTM D 2369:
				a.	Part A - 99.35 percent.
				b.	Part B - 59.23 percent.
				c.	Mixed - 91.3 percent.
			2.	Volatile Organic Compound (VOC), ASTM D 3960: 0.83 lb/gal (99 g/L).
			3.	Abrasion Resistance, ASTM D 4060: 18.8 mg loss CS-17 wheel, 1000 gram load, at 1000 revolutions.
			4.	Tensile Strength, ASTM D 2370: 6,250 psi (43,088 kPa).
			5.	Percent Elongation, ASTM D 2370: 6 percent.
			6.	Konig Hardness, 171.3 (3 mil film).
	** NOTE TO SPECIFIER ** Select colorant if required. Delete if not required.
			7.	Colorant:
				a.	Black.
				b.	White.
				c.	Light Gray.
				d.	Canada Gray.
				e.	Medium Gray.
				f.	Battleship Gray.
				g.	Sandy Beige.
				h.	Yellow.
				i.	Tile Red.
				j.	Rotunda Red.
				k.	Ivy Green.
				l.	Smoke Blue.
				m.	Regal Blue.
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			8.	Traction Grit:
				a.	Tennant 291 Grit (60 mesh) - white aluminum oxide.
	** NOTE TO SPECIFIER ** WEARGUARD-ITS™ is a high performance, one-component, moisture cured urethane for interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		C.	Gloss Urethane Topcoat: WEARGUARD-ITS, one component, moisture cured urethane topcoat.
			1.	Gloss Urethane Topcoat: One component, moisture cured aliphatic urethane topcoat.
				a.	Percent Solids, ASTM D 2369: 60 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 3.30 lb/gal (400 g/L).
				c.	Abrasion Resistance, ASTM D 4060: 30-40 mg loss, CS-17 wheel, 1000 gram load at 1000 revolutions.
				d.	Tensile Strength, ASTM D 2370: 5,000 psi (34,500 kPa).
				e.	Percent Elongation, ASTM D 2370: 120 percent.
				f.	Flexibility, ASTM D1522: Passes highest rating 1/8 inch.
				g.	Sward Hardness, ASTM D 2134: 32-36 (1 mil film).
	** NOTE TO SPECIFIER ** Select colorant if required. Delete if not required.
			2.	Colorant:
				a.	Canada Gray.
				b.	Medium Gray.
				c.	Battleship Gray.
				d.	Sandy Beige.
				e.	Tile Red.
				f.	Ivy Green.
				g.	Smoke Blue.
				h.	Regal Blue.
				i.	Black.
				j.	Yellow.
				k.	Rotunda Red.
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			3.	Traction Grit:
				a.	Tennant 291 Grit (60 mesh) - white aluminum oxide.
				b.	Tennant 292 Grit (30 mesh) - white aluminum oxide.
	** NOTE TO SPECIFIER ** WEARGUARD-CRU™ is a high performance, two-component, chemical resistant clear urethane coating for interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		D.	Gloss Urethane Topcoat: WEARGUARD-CRU, two component, clear chemical resistant urethane coating.
			1.	Chemical Resistant Urethane Topcoat: Two component, chemical resistant urethane topcoat.
				a.	Percent Solids, ASTM D 2369:
					1)	Part A - 76.5 percent.
					2)	Part B - 66.2 percent.
					3)	Mixed - 73.5 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: <3.3 lb/gal or <400 g/L.
				c.	Tensile Strength, ASTM D 2370: 6,000 psi (41,400 kPa).
				d.	Percent Elongation, ASTM D 2370: 45 percent.
				e.	Sward Hardness, ASTM D 2134: 52 (1 mil film).
				f.	König Hardness, ASTM D 4366: 165 (1 mil film).
	** NOTE TO SPECIFIER ** Eco-DFS™ and DFQ™ is a decorative system consisting of epoxy resin and colored quartz aggregate or vinyl flake chips and a aliphatic urethane topcoat for an attractive, slip-resistant surface on interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
	2.9	DECORATIVE FLOOR COATINGS
		A.	Eco-DQS - Decorative Quartz System. Eco-MPE resins and quartz aggregate topcoated with Eco-TCU.
			1.	Resurfacer Liquids: Eco-MPE two-component, 100 percent solids epoxy.
				a.	Percent Solids, ASTM D 2369:
					1)	Part A - 100 percent.
					2)	Part B - 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0.0 lb/gal (0 g/L).
				c.	Tensile Strength, ASTM D 2370: 8,000 psi (55,200 kPa).
				d.	Percent Elongation, ASTM D 2370: 5 percent.
			2.	Quartz Aggregate:
				a.	Aggregate Hardness, Moh's Mineral Scale: 6.5-7.
				b.	Light Stability: Shall be light stable.
			3.	Urethane Topcoat: Eco-TCU, two component, aliphatic urethane.
				a.	Percent Solids, ASTM D 2369:
					1)	Part A - 88.4 percent.
					2)	Part B - 93.6 percent.
					3)	Part A/B - 90.6 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0.9 lb/gal (100 g/L).
				c.	Tensile Strength, ASTM D 2370: 7,000 psi (48,300 kPa).
				d.	Percent Elongation, ASTM D 2370: 7 percent.
	** NOTE TO SPECIFIER ** Select colors required. Custom blends and solid colors are also available. Delete those not required.
			4.	Colors -Quartz:
				a.	Black Cherry.
				b.	Cinnamon Twist.
				c.	Cranberry Red.
				d.	Northwoods Green.
				e.	Sandstone.
				f.	Stone Gray.
				g.	Twilight Blue.
				h.	Wild Plum.
				i.	Custom as selected.
		B.	Eco-DFS - Decorative Flake System. Eco-MPE resins and vinyl flake chips topcoated with Eco-TCU.
			1.	Resurfacer Liquids: Eco-MPE two-component, 100 percent solids epoxy.
				a.	Percent Solids, ASTM D 2369:
					1)	Part A - 100 percent.
					2)	Part B - 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0.0 lb/gal (0 g/L).
				c.	Tensile Strength, ASTM D 2370: 8,000 psi (55,200 kPa).
				d.	Percent Elongation, ASTM D 2370: 5 percent.
			2.	Vinyl Flake.
				a.	Flake Size: 1/4 inch (6 mm).
				b.	Light Stability: Shall be light stable.
			3.	Urethane Topcoat: Eco-TCU, two component, aliphatic urethane.
				a.	Percent Solids, ASTM D 2369:
					1)	Part A - 88.4 percent.
					2)	Part B - 93.6 percent.
					3)	Part A/B - 90.6 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0.9 lb/gal (100 g/L).
				c.	Tensile Strength, ASTM D 2370: 7,000 psi (48,300 kPa).
				d.	Percent Elongation, ASTM D 2370: 7 percent.
	** NOTE TO SPECIFIER ** Select colors required. Custom blends and solid colors are also available. Delete those not required.
			4.	Colors - Flake:
				a.	Checkerboard.
				b.	Tweed.
				c.	Evergreen.
				d.	Storm.
				e.	Tornado.
				f.	Custom as selected.
		C.	Eco-DQS - Decorative Quartz System. Eco-MPE resins and quartz aggregate topcoated with Eco-URE.
			1.	Resurfacer Liquids: Eco-MPE two-component, 100 percent solids epoxy.
				a.	Percent Solids, ASTM D 2369:
					1)	Part A - 100 percent.
					2)	Part B - 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0.0 lb/gal (0 g/L).
				c.	Tensile Strength, ASTM D 2370: 8,000 psi (55,200 kPa).
				d.	Percent Elongation, ASTM D 2370: 5 percent.
			2.	Quartz Aggregate:
				a.	Aggregate Hardness, Moh's Mineral Scale: 6.5-7.
				b.	Light Stability: Shall be light stable.
			3.	UV Resistance Epoxy Topcoat: Eco-URE, two component, with UV resistance epoxy.
				a.	Percent Solids, ASTM D 2369:
					1)	Part A - 100 percent.
					2)	Part B - 100 percent.
					3)	Part A/B - 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0.05 lb/gal (100 g/L).
				c.	Tensile Strength, ASTM D 2370: 8,000 psi (55,200 kPa).
				d.	Percent Elongation, ASTM D 2370: 5 percent.
	** NOTE TO SPECIFIER ** Select colors required. Custom blends and solid colors are also available. Delete those not required.
			4.	Colors -Quartz:
				a.	Black Cherry.
				b.	Cinnamon Twist.
				c.	Cranberry Red.
				d.	Northwoods Green.
				e.	Sandstone.
				f.	Stone Gray.
				g.	Twilight Blue.
				h.	Wild Plum.
				i.	Custom as selected.
		D.	Eco-DFS - Decorative Flake System. Eco-MPE resins and vinyl flake chips topcoated with Eco-URE.
			1.	Resurfacer Liquids: Eco-MPE two-component, 100 percent solids epoxy.
				a.	Percent Solids, ASTM D 2369:
					1)	Part A - 100 percent.
					2)	Part B - 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0.0 lb/gal (0 g/L).
				c.	Tensile Strength, ASTM D 2370: 8,000 psi (55,200 kPa).
				d.	Percent Elongation, ASTM D 2370: 5 percent.
			2.	Vinyl Flake.
				a.	Flake Size: 1/4 inch (6 mm).
				b.	Light Stability: Shall be light stable.
			3.	UV Resistant Epoxy Topcoat: Eco-URE, two component, UV Resistant Epoxy.
				a.	Percent Solids, ASTM D 2369:
					1)	Part A - 100 percent.
					2)	Part B - 100 percent.
					3)	Part A/B - 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0.5lb/gal (100 g/L).
				c.	Tensile Strength, ASTM D 2370:8,000 psi (55,200 kPa).
				d.	Percent Elongation, ASTM D 2370: 5 percent.
	** NOTE TO SPECIFIER ** Select colors required. Custom blends and solid colors are also available. Delete those not required.
			4.	Colors - Flake:
				a.	Checkerboard.
				b.	Tweed.
				c.	Evergreen.
				d.	Storm.
				e.	Tornado.
				f.	Custom as selected.
	** NOTE TO SPECIFIER ** Eco-UVS(tm) and Eco-UVC(tm) are high performance, UV cured coatings for interior vinyl tile, sheet vinyl and concrete floors that cure instantly with the use of a UV light machine.
	2.10	UV CURED COATINGS
		A.	UV Cured Topcoat: Eco-UVC InstaCure+, two component, UV cured coating.
			1.	Percent Solids, ASTM D 2369: 88.63 percent.
			2.	Abrasion Resistance, ASTM D 4060: 65 mg loss CS-17 wheel, 1000 gram load at 1000 revolutions.
			3.	Coefficient of Friction, James Friction Tester, ASTM D2047: 0.54.
			4.	König Hardness, ASTM D 4366: 115 (1 mil film).
			5.	Finish, Gloss.
		B.	UV Cured Topcoat: Eco-UVS InstaCure, three component, UV cured coating.
			1.	Percent Solids, ASTM D 2369: 100 percent.
			2.	Abrasion Resistance, ASTM D 4060: 40-60 mg loss CS-17 wheel, 1000 gram load at 1000 revolutions.
			3.	Sward Hardness, ASTM D 2134: 20 (1 mil film).
			4.	König Hardness, ASTM D 4366: 120-140 (1 mil film).
			5.	Finish, Satin.
	** NOTE TO SPECIFIER ** MMA is a high performance, methyl methacrylate resin and decorative quartz or vinyl flake system for interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
	2.11	MMA (METHYL METHACRYLATE) SYSTEMS
		A.	MMA Double Broadcast Decorative Quartz System. MMA resins and quartz aggregate.
			1.	Primer Resin: Tennant MMA Primer: A two-component, high build, fast-setting methyl methacrylate primer.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM C307: 4,250 psi or 29.30 MPa.
				d.	Percent Elongation, ASTM D638: 3 percent.
				e.	Water Absorption, ASTM D570: <0.1 percent.
			2.	Broadcast Resin: MMA Body Coat. A two-component, high build, fast-setting methyl methacrylate broadcast resin.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM D638 and ASTM C307: 3,200 psi or 22.06 MPa and 2,100 or 14 MPa.
				d.	Percent Elongation, ASTM D638: 3 percent.
				e.	Water Absorption, ASTM D570: <0.1 percent.
			3.	Quartz Aggregate:
				a.	Aggregate Hardness, Moh's Mineral Scale: 6.5-7.
				b.	Light Stability: Light stable.
			4.	MMA Topcoat: Tennant MMA Topcoat. A two component, high build, fast setting methyl methacrylate topcoat.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM C307: 2,100 or 14 MPa.
				d.	Compressive Strength, ASTM C109: 7,500 psi, 52 MPa.
				e.	Water Absorption, ASTM D570: <0.1 percent.
	** NOTE TO SPECIFIER ** Select colors required. Custom blends and solid colors are also available. Delete those not required.
			5.	Colors -Quartz:
				a.	Black Cherry.
				b.	Cinnamon Twist.
				c.	Cranberry Red.
				d.	Northwoods Green.
				e.	Sandstone.
				f.	Stone Gray.
				g.	Twilight Blue.
				h.	Wild Plum.
				i.	Custom as selected.
		B.	MMA Double Broadcast Decorative Flake System. MMA resins and vinyl flake chips.
			1.	Primer Resin: Tennant MMA Primer: A two-component, high build, fast-setting methyl methacrylate primer.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM C307: 4,250 psi or 29.30 MPa.
				d.	Percent Elongation, ASTM D638: 3 percent.
				e.	Water Absorption, ASTM D570: <0.1 percent
			2.	Broadcast Resin: MMA Body Coat. A two-component, high build, fast-setting methyl methacrylate broadcast resin.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM D638 and ASTM C307: 3,200 psi or 22.06 MPa and 2,100 or 14 MPa.
				d.	Percent Elongation, ASTM D638: 3 percent.
				e.	Water Absorption, ASTM D570: <0.1 percent.
			3.	Vinyl Flake:
				a.	Flake Size: 1/4 inch (6 mm).
				b.	Light Stability: Light stable.
			4.	MMA Topcoat: Tennant MMA Topcoat. A two component, high build, fast setting methyl methacrylate topcoat.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM C307: 2,100 or 14 MPa.
				d.	Compressive Strength, ASTM C109: 7,500 psi, 52 MPa.
				e.	Water Absorption, ASTM D570: <0.1 percent.
			5.	Colors - Flake:
				a.	Checkerboard.
				b.	Tweed.
				c.	Evergreen.
				d.	Storm.
				e.	Tornado.
				f.	Custom as selected.
		C.	MMA Slurry Broadcast System, Quartz: MMA resins, filler and quartz aggregate.
			1.	Primer Resin: Tennant MMA Primer: A two-component, high build, fast-setting methyl methacrylate primer.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM C307: 4,250 psi or 29.30 MPa.
				d.	Percent Elongation, ASTM D638: 3 percent.
				e.	Water Absorption, ASTM D570: <0.1 percent
			2.	Broadcast Resin: MMA Body Coat. A two-component, high build, fast-setting methyl methacrylate broadcast resin.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM D638 and ASTM C307: 3,200 psi or 22.06 MPa and 2,100 or 14 MPa.
				d.	Percent Elongation, ASTM D638: 3 percent.
				e.	Water Absorption, ASTM D570: <0.1 percent.
			3.	Quartz Aggregate:
				a.	Aggregate Hardness, Moh's Mineral Scale: 6.5-7.
				b.	Light Stability: Light stable.
			4.	MMA Topcoat: Tennant MMA Topcoat. A two component, high build, fast setting methyl methacrylate topcoat.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM C307: 2,100 or 14 MPa.
				d.	Compressive Strength, ASTM C109: 7,500 psi, 52 MPa.
				e.	Water Absorption, ASTM D570: <0.1 percent.
	** NOTE TO SPECIFIER ** Select colors required. Custom blends and solid colors are also available. Delete those not required.
			5.	Colors -Quartz:
				a.	Black Cherry.
				b.	Cinnamon Twist.
				c.	Cranberry Red.
				d.	Northwoods Green.
				e.	Sandstone.
				f.	Stone Gray.
				g.	Twilight Blue.
				h.	Wild Plum.
				i.	Custom as selected.
		D.	MMA Slurry Broadcast System, Flake: MMA resins, filler and vinyl flake chips.
			1.	Primer Resin: Tennant MMA Primer: A two-component, high build, fast-setting methyl methacrylate primer.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM C307: 4,250 psi or 29.30 MPa.
				d.	Percent Elongation, ASTM D638: 3 percent.
				e.	Water Absorption, ASTM D570: <0.1 percent
			2.	Broadcast Resin: MMA Body Coat. A two-component, high build, fast-setting methyl methacrylate broadcast resin.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM D638 and ASTM C307: 3,200 psi or 22.06 MPa and 2,100 or 14 MPa.
				d.	Percent Elongation, ASTM D638: 3 percent.
				e.	Water Absorption, ASTM D570: <0.1 percent.
			3.	Vinyl Flake:
				a.	Flake Size: 1/4 inch (6 mm).
				b.	Light Stability: Light stable.
			4.	MMA Topcoat: Tennant MMA Topcoat. A two component, high build, fast setting methyl methacrylate topcoat.
				a.	Percent Active Resin: 100 percent.
				b.	Volatile Organic Compound (VOC), ASTM D 3960: 0 g/L).
				c.	Tensile Strength, ASTM C307: 2,100 or 14 MPa.
				d.	Compressive Strength, ASTM C109: 7,500 psi, 52 MPa.
				e.	Water Absorption, ASTM D570: <0.1 percent.
			5.	Colors - Flake:
				a.	Checkerboard.
				b.	Tweed.
				c.	Evergreen.
				d.	Storm.
				e.	Tornado.
				f.	Custom as selected.
	2.12	SEALER
	** NOTE TO SPECIFIER ** Eco-Hard-N-Seal™ is a high performance, sodium silicate hardener sealer for interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		A.	Hardener/Sealer: Tennant Eco-Hard-N-Seal. Sodium silicate hardener.
			1.	Percent Solids, ASTM D 2369: 19.8 percent.
			2.	Volatile Organic Compound (VOC), ASTM D 3960: 0 lb/gal or 0 kg/L.
	PART 3	EXECUTION
	3.1	EXAMINATION
		A.	Examine concrete surface to receive floor coating system. Do not begin surface preparation of application until unacceptable conditions have been corrected.
		B.	Notify Architect of unsatisfactory conditions before proceeding.
	3.2	PREPARATION
		A.	Allow concrete substrate to cure a minimum of 30 days.
	** NOTE TO SPECIFIER ** Although testing is critical, it is not a guarantee against future problems. This is especially true if there is no vapor barrier or the vapor barrier is not functioning properly and/or you suspect you may have concrete contamination from oils, chemical spills or excessive salts.
		B.	Test concrete for moisture in accordance with ASTM F 1869 or ASTM F 2170. Except where otherwise specified, readings shall be below 3 pounds per 1,000 square feet over a 24-hour period on the calcium chloride test or below 70 percent relative internal concrete humidity.
		C.	Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
			1.	Cleaning: Scrub with Tennant detergent and rinse with clean water to remove surface dirt, grease and oil.
			2.	Remove coating or membranes for existing concrete with one of the following methods:
				a.	Shot blast.
				b.	Scarify.
				c.	Diamond Grinding.
			3.	Sweep and vacuum concrete surface.
			4.	Use magnetic broom to remove excess shot.
			5.	For thin mil applications (3-10 mils), the floor can be mechanically prepared using the Tennant EasyPrep system:
				a.	Use 100 grit concrete tools on bare concrete.
				b.	Use 100 grit polymer tools to abrade existing coating for recoat.
	** NOTE TO SPECIFIER ** Include the following paragraphs for use only when the moisture mitigation coating is specified. Coordination with one coat 7 mil or two coat 15 mil coating as specified under Products above.
		D.	Prepare surfaces for moisture mitigation coating installation using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
			1.	Test concrete for moisture in accordance with ASTM 1869.
				a.	7-Mil System: Concrete must be less than one year old and readings must not be greater than 10 lbs (4.5 kgs) per 1,000 sq ft (92.9 sq m) in 24 hours.
				b.	15-Mil System: For fully cured concrete readings must not be greater than 15 lbs (6.8 kgs) per 1,000 sq ft (92.9 sq m) in 24 hours.
			2.	Cleaning: Scrub with Tennant detergent and rinse with clean water to remove surface dirt, grease and oil.
			3.	Remove coating or membranes for existing concrete as followings:
				a.	Shot blast.
			4.	Sweep and vacuum concrete surface.
			5.	Use magnetic broom to remove excess shot.
	** NOTE TO SPECIFIER ** Eco-MVR™ Eco-MVR must be topcoated with at least 8 mils of epoxy and floor surface must be shotblasted to a CSP 3-4 profile prior to application.
	3.3	MOISTURE MITIGATION COATING INSTALLATION
		A.	Install in accordance with manufacturer's instructions.
		B.	Moisture Mitigation Coating:
			1.	Material: Eco-MVR – Moisture Vapor Reducer.
			2.	Open only enough material that can be applied within 25 minutes.
			3.	Mix components together.
	** NOTE TO SPECIFIER ** Select the one of the following two paragraphs as required and delete the one not required.
			4.	7 mil system:
				a.	Apply at the rate of 225 sf/gal.
				b.	Allow coating to hard cure before applying additional coatings. See Product Bulletin for hard cure times.
			5.	15 mil system:
				a.	Apply prime coat at the rate of 321 sf/gal.
				b.	After the prime coat becomes tacky and within 24 hours apply a second coat of Eco-MVR at the rate of 160 sf/gal. Total dry film thickness must be 15 mils or greater.
				c.	Allow coating to hard cure before applying additional coatings. See Product Bulletin for hard cure times.
	3.4	RESURFACER INSTALLATION
		A.	Install in accordance with manufacturer's instructions.
	** NOTE TO SPECIFIER ** The following paragraph is applicable for the Eco-PT™ 250 resurfacer system consisting of Eco-MPE™ primer and Eco-PT™ 250 Resurfacers and Eco-PT™ Topcoat as the grout coat.
		B.	Resurfacer System: Eco-PT250.
			1.	Primer:
				a.	Eco-MPE - Muti-Purpose Epoxy.
				b.	Mix components in accordance with manufacturer's instructions.
				c.	Open only enough material that can be applied within 25 minutes.
				d.	Apply at the rate of 150-250 sf/gal.
			2.	Resurfacer Eco-PT 250:
				a.	Mix resurfacer components together in a mortar mixer.
				b.	Place mixed material within 15 minutes.
				c.	Pour mixed material into screed box and screed over desired area.
				d.	Power trowel to compact and achieve finished texture.
				e.	Allow resurfacer to cure 6 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
				f.	Remove high spots and imperfections using a terrazzo grinder.
				g.	Vacuum up loose material and dust.
			3.	Grout Coat: Eco-PT Topcoat:
				a.	Mix components in accordance with manufacturer's instructions.
				b.	Open only enough material that can be applied within 25 minutes.
				c.	Apply at the rate of 150-250 sf/gal.
			4.	Optional topcoats can be applied.
	** NOTE TO SPECIFIER ** Eco-CTO™ is a filled three-component, water-based cementitious-polyurethane for resurfacing interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		C.	Cementitious Trowel Overlay: Eco-CTO, a three-component water- based cementitious-polyurethane.
	** NOTE TO SPECIFIER ** Cove is optional, select if required and delete if not required.
			1.	Optional Cove:
				a.	Cove Primer: Eco-CVP Cementitious Vertical Primer:
					1)	Mix primer components together.
					2)	Mix only enough material, which can be applied within 15 minutes.
					3)	Apply at the rate of 30 lineal feet (4 inch cove height) per unit.
				b.	Cove Overlay: Eco-CVO, Cementitious Vertical Overlay.
					1)	Mix cove components together.
					2)	Mix only enough material, which can be blended and coved within a 20-minute period.
					3)	Apply at the rate of 30 lineal feet (4 inch cove height) at 3/16 inch per unit.
			2.	Overlay: Eco-CTO - Cementitious Trowel Overlay.
				a.	Mix overlay components together in a mortar mixer.
				b.	Pour the mixed material into screed box and screed over desired area.
				c.	Mixed material must be screeded and troweled within 20 minutes.
				d.	Compact and level material to achieve finished texture.
			3.	Allow overlay to cure 12 hours at 70 degrees F (20 degrees C).
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			4.	Traction Grit: Silica Sand.
		D.	Cementitious Workable Overlay: Eco-CWO, a three-component water- based cementitious-polyurethane.
	** NOTE TO SPECIFIER ** Cove is optional, select if required and delete if not required.
			1.	Optional Cove:
				a.	Cove Primer: Eco-CVP Cementitious Vertical Primer:
					1)	Mix primer components together.
					2)	Mix only enough material, which can be applied within 15 minutes.
					3)	Apply at the rate of 30 lineal feet (4 inch cove height) per unit.
				b.	Cove Overlay: Eco-CVO, Cementitious Vertical Overlay.
					1)	Mix cove components together.
					2)	Mix only enough material, which can be blended and coved within a 20-minute period.
					3)	Apply at the rate of 30 lineal feet (4 inch cove height) at 3/16 inch per unit.
			2.	Overlay: Eco-CWO - Cementitious Workable Overlay.
				a.	Mix overlay components together in a mortar mixer.
				b.	Pour the mixed material into screed box and screed over desired area.
				c.	Mixed material must be screeded and troweled within 20 minutes.
				d.	Compact and level material to achieve finished texture.
			3.	Allow overlay to cure 12 hours at 70 degrees F (20 degrees C).
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			4.	Traction Grit: Silica Sand.
	** NOTE TO SPECIFIER ** Eco-CFO(tm) is a filled three-component, water-based cementitious-polyurethane for resurfacing interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		E.	Cementitious Flowable Overlay: Eco-CFO, a three-component water- based cementitious-polyurethane.
			1.	Overlay: Eco-CFO - Cementitious Flowable Overlay.
				a.	Mix overlay components together in a mortar mixer.
				b.	Pour the mixed material onto flow and rake over desired area.
				c.	Level material to achieve finished texture.
			2.	Allow overlay to cure 12 hours at 70 degrees F (20 degrees C).
	** NOTE TO SPECIFIER ** Cove is optional, select if required and delete if not required.
			3.	Optional Cove:
				a.	Cove Primer: Eco-CVP Cementitious Vertical Primer:
					1)	Mix primer components together.
					2)	Mix only enough material, which can be applied within 15 minutes.
					3)	Apply at the rate of 30 lineal feet (4 inch cove height) per unit.
				b.	Cove Overlay: Eco-CVO, Cementitious Vertical Overlay.
					1)	Mix cove components together.
					2)	Mix only enough material, which can be blended and coved within a 20-minute period.
					3)	Apply at the rate of 30 lineal feet (4 inch cove height) at 3/16 inch per unit.
	3.5	PRIMER INSTALLATION
		A.	Install in accordance with manufacturer's instructions.
	** NOTE TO SPECIFIER ** The following paragraph is applicable for Eco-MPE™, Eco-RCE™ and Eco-FSE™ primers. Select the products required and delete those not required.
		B.	Primer:
			1.	Material:
	** NOTE TO SPECIFIER ** Select the following paragraphs as required and delete the one(s) not required.
				a.	Eco-MPE - Muti-Purpose Epoxy.
				b.	Eco-RCE/M- Rapid Cure Epoxy/ Moderate.
				c.	Eco-RCE/F- Rapid Cure Epoxy/ Fully.
				d.	Eco-RCE - Rapid Cure Epoxy.
				e.	Eco-CEP - Colored Epoxy primer.
			2.	Mix components in accordance with manufacturer's instructions.
			3.	Open only enough material that can be applied within 25 minutes.
			4.	Apply at the rate of 321-535 Sf/gal.
			5.	Allow coating to cure 2 to 6 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
	3.6	EPOXY COATING INSTALLATION
		A.	Install in accordance with manufacturer's instructions.
	** NOTE TO SPECIFIER ** The following paragraph is applicable for Eco-MPE(tm), Eco-FSE(tm) and Eco-CPE epoxy coatings. Select the products required and delete those not required.
		B.	Epoxy Coating:
			1.	Material:
	** NOTE TO SPECIFIER ** Select one of the following paragraphs and delete the ones not required.
				a.	Eco-MPE - Muti-Purpose Epoxy.
				b.	Eco-RCE/M- Rapid Cure Epoxy/ Moderate.
				c.	Eco-RCE/F- Rapid Cure Epoxy/ Fully.
				d.	Eco-RCE- Rapid Cure Epoxy.
				e.	Eco-CEP - Colored Epoxy Primer.
			2.	Mix only enough material that can be applied within 25 minutes.
			3.	Apply at the rate of 53-321 Sf/gal while the prime coat is still tacky.
			4.	Allow coating to cure 16 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
	** NOTE TO SPECIFIER ** Eco-CRE™ is a chemical resistant, two-component, 100 percent solids epoxy for interior concrete floors.
		C.	Chemical Resistant Epoxy:
			1.	Material: Eco-CRE - Chemical Resistant Epoxy.
			2.	Open only enough material that can be applied within 25 minutes.
			3.	Prime Coat:
				a.	Apply prime coat at the rate of 325-535 sf/gal.
				b.	Allow coating to cure 2-6 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
			4.	Finish Coat:
				a.	Apply finish coat at the rate of 200-267 sf/gal.
				b.	Allow coating to cure 24 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			5.	Traction Grit: Tennant 291 Grit (60 mesh) - white aluminum oxide.
	** NOTE TO SPECIFIER ** Eco-Shield(tm) is a filled three-component, 100 percent solids epoxy for resurfacing interior concrete floors. Complies with L.A. Rule 66 and VOC/VOS Rules and Regulations.
		D.	High Wear Epoxy: Eco-Shield, three-component, 100 percent solids epoxy.
			1.	Coating: Eco-Shield.
				a.	Mix components together.
				b.	Mix only enough material, which can be applied within 20 minutes.
				c.	Apply Eco-Shield at the rate of 321-535 ft2/gal.
				d.	Porous concrete may require a second coat. Apply the second coat while the first is still tacky.
			2.	Allow coating to cure 16 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
	3.7	ESD COATING INSTALLATION
		A.	Electrostatic Conductive Primer: Eco-ECP, two-component epoxy.
			1.	Coating: Eco-ECP.
				a.	Install grounding system to customer's specifications.
				b.	Mix components together.
				c.	Mix only enough material, which can be applied within 20 minutes.
				d.	Apply Eco-ECP at the rate of 321-535 ft2/gal.
			2.	Coating must be set up enough to walk on before applying Eco-ECT Topcoat.
		B.	Electrostatic Dissipative Primer: Eco-EDP, two-component epoxy.
			1.	Coating: Eco-EDP.
				a.	Install grounding system to customer's specifications.
				b.	Mix components together.
				c.	Mix only enough material, which can be applied within 20 minutes.
				d.	Apply Eco-EDP at the rate of 321-535 ft2/gal.
			2.	Coating must be set up enough to walk on before applying Eco-ECT or ECO EDE Topcoat.
		C.	Electrostatic Dissipative Epoxy: Eco-EDE, three-component, 100 percent solids epoxy.
			1.	Coating: Eco-EDE.
				a.	Premix components per manufactures instructions.
				b.	Mix components together.
				c.	Mix only enough material, which can be applied within 20 minutes.
				d.	Apply Eco-EDE at the rate of 20-32 ft2/gal.
			2.	Allow coating to cure 24 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
		D.	Electrostatic Control Epoxy: Eco-ECT, two-component, 100 percent solids epoxy.
			1.	Coating: Eco-ECT.
				a.	Premix components per manufactures instructions.
				b.	Mix components together.
				c.	Mix only enough material, which can be applied within 20 minutes.
				d.	Apply Eco-ECT at the rate of 80-107 ft2/gal.
			2.	Allow coating to cure 24 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
	3.8	URETHANE COATING INSTALLATION
		A.	Install in accordance with manufacturer's instructions.
	** NOTE TO SPECIFIER ** Eco-HTS 100(tm) is a 100 g/L reduced VOC, low odor, three-component, moisture cured, aliphatic urethane for interior concrete floors. Eco-HTS(tm) can be applied over Eco-Shield(tm), Eco-MPE(tm), Eco-FSE(tm), Eco-CEP(tm) or Eco-RCE(tm) based on the prep method and required thickness. Complies with all current U.S. VOC/VOS Rules and Regulations.
		B.	Satin Urethane Topcoat: Eco-HTS 100, 100 g/L reduced VOC, low odor, three-component, moisture cured, aliphatic urethane.
			1.	Topcoat Coating: Eco-HTS 100.
				a.	Open and mix only enough material, which can be applied in a 2 hour period.
				b.	Apply Eco-HTS at the rate of 500 sf/gal.
				c.	Allow coating to dry 24 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
	** NOTE TO SPECIFIER ** Eco-HPS 100(tm) is a high performance, 100 g/L reduced VOC, low odor, two-component aliphatic, moisture cured topcoat for interior concrete floors. Eco-HPS can be applied over Eco-Shield, Eco-MPE(tm), Eco-FSE(tm), Eco-CEP(tm) or Eco-RCE(tm) based on the prep method and required thickness. Complies with all current U.S. VOC/VOS Rules and Regulations.
		C.	Gloss Urethane Topcoat: Eco-HPS 100, 100 g/L reduced VOC, low odor, two-component aliphatic, moisture cured urethane topcoat.
			1.	Topcoat Coating: Eco-HPS.
				a.	Open and mix only enough material, which can be applied in a 2 hour period.
				b.	Apply Eco-HPS at the rate of 500 ft2/gal.
				c.	Allow coating to dry 24 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
	** NOTE TO SPECIFIER ** WEARGUARD-ITS(tm) is a high performance, one-component, moisture cured urethane for interior concrete floors.
		D.	Gloss Urethane Topcoat: WEARGUARD-ITS, one component moisture cured urethane topcoat.
			1.	Gloss Urethane Topcoat: One component, moisture cured aliphatic urethane topcoat.
				a.	Mix components together and add bonding additive.
				b.	Open and mix only enough material, which can be applied in a 2 hour period.
				c.	Apply at the rate of 350-450 sf/gal.
				d.	Allow coating to dry 5 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
				e.	Sand with 100 grit sandpaper, detergent scrub and rinse with clean water to ensure adequate adhesion between coats.
				f.	Apply second coat at the rate of 350-450 sf/gal.
				g.	Allow coating to dry 12 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
	** NOTE TO SPECIFIER ** Traction grit is optional, select if required and delete if not required.
			2.	Traction Grit: Tennant 291 Grit (60 mesh) - white aluminum oxide
	** NOTE TO SPECIFIER ** WEARGUARD-CRU™ is a high performance, two-component, chemical resistant urethane coating for interior concrete floors. Use over Eco-CRU primer for chemically prepped floors. Use MPE, FSE, CEP or RCE primers and epoxy coats for mechanically prepped floors.
		E.	Gloss Urethane Topcoat: WEARGUARD-CRU, two component, chemical resistant urethane coating.
			1.	Coating: CRU Chemical Resistant Urethane Topcoat.
				a.	Open and mix only enough material, which can be applied in a 2-hour period.
				b.	Apply CRU at the rate of 400 sf/gal.
				c.	Allow coating to dry 12 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
				d.	Apply second coat of CRU.
				e.	Allow coating to dry 24 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
	3.9	DECORATIVE FLOOR COATING INSTALLATION
		A.	Install in accordance with manufacturer's instructions.
		B.	Eco-DFS - Decorative Flake System. Eco-MPE, two-component epoxy primer and a Eco-TCU two component, moisture cured, aliphatic urethane topcoat.
			1.	Seed Coats: Eco-DFS - Decorative Flake Solutions.
				a.	Mix Eco-MPE primer components together.
				b.	Mix only enough material, which can be applied within 25 minutes.
				c.	Apply Eco-MPE at the rate of 160-267 sf/gal.
				d.	Immediately broadcast decorative flake into the resin system at the rate of 0.2 pounds per SF.
				e.	Allow coating to cure 8-12 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
				f.	Apply second coat Eco-MPE at 107 sf/gal and broadcast.
			2.	Topcoat: Eco-TCU -- Thick Coat Urethane.
			3.	Mix components together.
			4.	Mix only enough material, which can be applied within 15 minutes.
			5.	Apply Eco-TCU at the rate of 107 Sf/gal.
			6.	Allow coating to dry 24 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
			7.	If less texture is desired, apply Eco-TCU at the rate of 200 sf/gal within 24 hours of applying the previous coat.
	** NOTE TO SPECIFIER ** Base is optional, select if required and delete if not required.
			8.	Base:
				a.	Provide base as indicated on the Drawings.
				b.	Cove Base: Provide a 4 inch cove base as indicated.
		C.	Eco-DQS - Decorative Quartz System. Eco-MPE, two-component epoxy quartz aggregate and Eco-TCU two component, moisture cured, aliphatic urethane topcoat.
			1.	Seed Coats: Eco-DQS - Decorative Quartz Solutions.
				a.	Mix Eco-MPE primer components together.
				b.	Mix only enough material, which can be applied within 25 minutes.
				c.	Apply Eco-MPE at the rate of 160-267 sf/gal.
				d.	Immediately broadcast decorative quartz granules into the resin system at the rate of 0.4 to 0.5 pounds per SF.
				e.	Allow coating to cure 8-12 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
				f.	Apply second coat Eco-MPE at 107 sf/gal and broadcast.
			2.	Topcoat: Eco-TCU -- Thick Coat Urethane
			3.	Mix components together.
			4.	Mix only enough material, which can be applied within 15 minutes.
			5.	Apply Eco-TCU at the rate of 107 Sf/gal.
			6.	Allow coating to dry 24 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
			7.	If less texture is desired, apply Eco-TCU at the rate of 200 sf/gal within 24 hours of applying the previous coat.
	** NOTE TO SPECIFIER ** Base is optional, select if required and delete if not required.
			8.	Base:
				a.	Provide base as indicated on the Drawings.
				b.	Cove Base: Provide a 4 inch cove base as indicated.
		D.	Eco-DFS - Decorative Flake System. Eco-MPE, two-component epoxy primer and Eco-URE a two component, UV resistant epoxy topcoat.
			1.	Seed Coats: Eco-DFS - Decorative Flake Solutions.
				a.	Mix Eco-MPE primer components together.
				b.	Mix only enough material, which can be applied within 25 minutes.
				c.	Apply Eco-MPE at the rate of 160-267 sf/gal.
				d.	Immediately broadcast decorative flake into the resin system at the rate of 0.2 pounds per SF.
				e.	Allow coating to cure 8-12 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
				f.	Apply second coat Eco-MPE at 107 sf/gal and broadcast.
			2.	Topcoat: Eco-URE – UV Resistant Epoxy.
			3.	Mix components together.
			4.	Mix only enough material, which can be applied within 15 minutes.
			5.	Apply Eco-URE at the rate of 107 Sf/gal.
			6.	Allow coating to dry 24 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
			7.	If less texture is desired, apply Eco-URE at the rate of 200 sf/gal within 24 hours of applying the previous coat.
	** NOTE TO SPECIFIER ** Base is optional, select if required and delete if not required.
			8.	Base:
				a.	Provide base as indicated on the Drawings.
				b.	Cove Base: Provide a 4 inch cove base as indicated.
		E.	Eco-DQS - Decorative Quartz System. Eco-MPE, two-component epoxy quartz aggregate and Eco-URE a two component, UV resistant epoxy topcoat
			1.	Seed Coats: Eco-DQS - Decorative Quartz Solutions.
				a.	Mix Eco-MPE primer components together.
				b.	Mix only enough material, which can be applied within 25 minutes.
				c.	Apply Eco-MPE at the rate of 160-267 sf/gal.
				d.	Immediately broadcast decorative quartz granules into the resin system at the rate of 0.4 to 0.5 pounds per SF.
				e.	Allow coating to cure 8-12 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
				f.	Apply second coat Eco-MPE at 107 sf/gal and broadcast.
			2.	Topcoat: Eco-URE – UV Resistant Epoxy.
			3.	Mix components together.
			4.	Mix only enough material, which can be applied within 15 minutes.
			5.	Apply Eco-URE at the rate of 107 Sf/gal.
			6.	Allow coating to dry 24 hours at 75 degrees F (24 degrees C) and 50 percent relative humidity.
			7.	If less texture is desired, apply Eco-URE at the rate of 200 sf/gal within 24 hours of applying the previous coat.
	** NOTE TO SPECIFIER ** Base is optional, select if required and delete if not required.
			8.	Base:
				a.	Provide base as indicated on the Drawings.
				b.	Cove Base: Provide a 4 inch cove base as indicated.
	** NOTE TO SPECIFIER ** Eco-UVS(tm) and Eco-UVC are high performance coatings for interior vinyl tile, sheet vinyl and concrete floors that cure instantly with the use of a UV light machine.
	3.10	UV COATING INSTALLATION
		A.	Install in accordance with manufacturer's instructions.
		B.	UV Cured Coating Eco-UVC InstaCure+, two component, UV cured coating.
			1.	Preparation requirements vary based on the type of substrate being coated. See manufactures instructions.
			2.	Apply at the rate of 500 Sf/gal.
			3.	Cure coating with UV light machine.
		C.	UV Cured Coating Eco-UVS, three component, UV cured coating.
			1.	Preparation requirements vary based on the type of substrate being coated. See manufactures instructions.
			2.	Apply at the rate of 500 Sf/gal.
			3.	Cure coating with UV light machine.
	3.11	MMA (METHYL METHACRYLATE) INSTALLATION
		A.	Install in accordance with manufacturer's instructions.
		B.	Provide sufficient ventilation. All fans must be explosion proof and grounded.
		C.	MMA Double Broadcast Decorative Flake System. MMA resins and vinyl flake chips.
			1.	Primer: MMA Primer.
				a.	Mix components together. Tennant MMA Bonding Additive must be used in primer.
				b.	Do not mix more than 1.25 gallons of material (combined Primer Resin and Bonding Additive) at one time.
				c.	Immediately after mixing, pour all the material on the floor to dissipate the heat.
				d.	Apply Tennant MMA Primer at the rate of 90-110 sf/gal.
				e.	Allow coating to cure until it is completely tack free before applying the next coat.
			2.	Patching/Sloping (if required).
				a.	Mix MMA Polymer Concrete as recommended by manufacturer. Use mixture for repair and sloping as needed.
			3.	Seed Coats: MMA Body Coat and vinyl flake chips.
				a.	Mix MMA Body Coat components together. MMA Body Coat may be colored to increase hide of the substrate.
				b.	Do not mix more than 1 gallon of material at a time. Immediately after mixing, pour all the material onto the floor to dissipate heat.
				c.	Apply Tennant MMA Body Coat at 100 sf/gal. (See appropriate product bulletin for mixing and application instructions).
				d.	Immediately broadcast decorative flake to rejection. Approximate usage rate for 1/4 inch (6 mm) flake is 0.20-0.25 lbs per sq/f.
				e.	Allow to cure until completely tack free.
				f.	Sweep and vacuum to remove excess flake.
				g.	Apply second coat Tennant MMA Body Coat at 100 sf/gal and broadcast.
				h.	Allow to dry until completely tack free and remove excess flake.
			4.	Topcoat MMA Clear Topcoat.
				a.	Flake broadcast must be topcoated with MMA Clear Topcoat after broadcast resin is completely tack free.
				b.	Mix components together.
				c.	Do not mix more than 1 gallons of material at one time. Immediately after mixing, pour all the material onto the floor to dissipate heat.
				d.	Apply at 80-90 sf/gal
				e.	Apply second topcoat at a coverage rate of 90-110 sf/gal.
	** NOTE TO SPECIFIER ** Base is optional, select if required and delete if not required.
			5.	Base:
				a.	Provide base as indicated on the Drawings.
				b.	Cove Base: Provide a 4 inch cove base as indicated.
		D.	MMA Double Broadcast Decorative Quartz System. MMA resins and quartz aggregate.
			1.	Primer: MMA Primer.
				a.	Mix components together. MMA Bonding Additive must be used in primer.
				b.	Do not mix more than 1.25 gallons of material (combined Primer Resin and Bonding Additive) at one time.
				c.	Immediately after mixing, pour all the material on the floor to dissipate the heat.
				d.	Apply MMA Primer at the rate of 90-110 sf/gal.
				e.	Allow coating to cure until it is completely tack free before applying the next coat.
			2.	Patching/Sloping (if required).
				a.	Mix MMA Polymer Concrete as recommended by manufacturer. Use mixture for repair and sloping as needed.
			3.	Seed Coats: MMA Body Coat and quartz aggregate.
				a.	Mix MMA Body Coat components together. MMA Body Coat may be colored to increase hide of the substrate.
				b.	Do not mix more than 1 gallon of material at a time. Immediately after mixing, pour all the material onto the floor to dissipate heat.
				c.	Apply Tennant MMA Body Coat at 100 sf/gal. (See appropriate product bulletin for mixing and application instructions).
				d.	Immediately broadcast quartz aggregate to rejection. Approximate usage rate is 0.50 lbs per sq/f.
				e.	Allow to cure until completely tack free.
				f.	Sweep and vacuum to remove excess quartz.
				g.	Apply second coat MMA Body Coat at 100 sf/gal and broadcast.
				h.	Allow to dry until completely tack free and remove excess quartz.
			4.	Topcoat: MMA Clear Topcoat.
				a.	Quartz broadcast must be topcoated with MMA Clear Topcoat after broadcast resin is completely tack free.
				b.	Mix components together.
				c.	Do not mix more than 1 gallon of material at a time. Immediately after mixing, pour all the material onto the floor to dissipate heat.
				d.	Apply at 80-90 sf/gal
				e.	Apply second topcoat at a coverage rate of 90-110 sf/gal.
	** NOTE TO SPECIFIER ** Base is optional, select if required and delete if not required.
			5.	Base:
				a.	Provide base as indicated on the Drawings.
				b.	Cove Base: Provide a 4 inch (101 mm) cove base as indicated.
		E.	MMA Broadcast Slurry System, Flake: MMA resins, filler and vinyl flake chips.
			1.	Primer: MMA Primer.
				a.	Mix components together. MMA Bonding Additive must be used in primer.
				b.	Do not mix more than 1.25 gallons of material (combined Primer Resin and Bonding Additive) at one time.
				c.	Immediately after mixing, pour all the material on the floor to dissipate the heat.
				d.	Apply MMA Primer at the rate of 90-110 sf/gal.
				e.	Allow coating to cure until it is completely tack free before applying the next coat.
			2.	Patching/Sloping (if required).
				a.	Mix MMA Polymer Concrete as recommended by manufacturer. Use mixture for repair and sloping as needed.
			3.	Slurry Coat: MMA Body Coat with filler and vinyl flake chips.
				a.	Mix MMA Body Coat components together per manufactures instructions. MMA Body Coat may be colored to increase hide of the substrate.
				b.	Do not mix more than 2 gallons of material at a time. Immediately after mixing, pour all the material onto the floor to dissipate heat.
				c.	Apply MMA Body Coat with a gauged rake set at 1/8 inch (3 mm) or 3/16 inch (5 mm) (See appropriate product bulletin for mixing and application instructions).
				d.	Use a porcupine roller to level the material and to release any entrapped air.
				e.	Immediately broadcast decorative flake to rejection. Approximate usage rate for 1/8 (3 mm) flake is 0.17 lbs per sq/f.
				f.	Allow to cure until completely tack free.
				g.	Sweep and vacuum to remove excess flake.
			4.	Topcoat: MMA Clear Topcoat.
				a.	Flake broadcast must be topcoated with MMA Clear Topcoat after broadcast resin is completely tack free.
				b.	Mix components together.
				c.	Do not mix more than 1 gallon of material at one time.
				d.	Immediately after mixing, pour all the material on the floor to dissipate the heat.
				e.	Apply at 80-90 sf/gal
				f.	Allow coating to cure until it is completely tack free before applying the next coat.
				g.	Apply 2nd topcoat at a coverage rate of 90-110 sf/gal.
	** NOTE TO SPECIFIER ** Base is optional, select if required and delete if not required.
			5.	Base:
				a.	Provide base as indicated on the Drawings.
				b.	Cove Base: Provide a 4 inch (101 mm) cove base as indicated on the Drawings.
		F.	MMA Broadcast Slurry System, Quartz: MMA resins, filler and quartz aggregate.
			1.	Primer: MMA Primer.
				a.	Mix components together. MMA Bonding Additive must be used in primer.
				b.	Do not mix more than 1.25 gallons of material (combined Primer Resin and Bonding Additive) at one time.
				c.	Immediately after mixing, pour all the material on the floor to dissipate the heat.
				d.	Apply MMA Primer at the rate of 90-110 sf/gal.
				e.	Allow coating to cure until it is completely tack free before applying the next coat.
			2.	Patching/Sloping (if required).
				a.	Mix MMA Polymer Concrete as recommended by manufacturer. Use mixture for repair and sloping as needed.
			3.	Slurry Coat: MMA Body Coat with filler and quartz aggregate.
				a.	Mix MMA Body Coat components per manufacture's instructions. MMA Body Coat may be colored to increase hide of the substrate.
				b.	Do not mix more than 2 gallons of material at a time. Immediately after mixing, pour all the material onto the floor to dissipate heat.
				c.	Apply MMA Body Coat with a gauged rake set at 1/8 inch (3 mm) or 3/16 inch (5 mm) (See appropriate product bulletin for mixing and application instructions).
				d.	Use a porcupine roller to level the material and to release any entrapped air.
				e.	Immediately broadcast decorative quartz to rejection. Approximate usage rate for 1/8 inch (3 mm) is 0.80 lbs per sq/f.
				f.	Allow to cure until completely tack free.
				g.	Sweep and vacuum to remove excess quartz.
			4.	Topcoat: MMA Clear Topcoat.
				a.	Flake broadcast must be topcoated with MMA Clear Topcoat after broadcast resin is completely tack free.
				b.	Mix components together.
				c.	Do not mix more than 1 gallon of material at one time.
				d.	Immediately after mixing, pour all the material on the floor to dissipate the heat.
				e.	Apply at 80-90 sf/gal
				f.	Allow coating to cure until it is completely tack free before applying the next coat.
				g.	Apply 2nd topcoat at a coverage rate of 90-110 sf/gal.
	** NOTE TO SPECIFIER ** Base is optional, select if required and delete if not required.
			5.	Base:
				a.	Provide base as indicated on the Drawings.
				b.	Cove Base: Provide a 4 inch (101 mm) cove base as indicated on the Drawings.
	3.12	FIELD QUALITY CONTROL
		A.	Coating manufacturers representative to verify that installation is in conformance to the manufacturer's recommendations.
	3.13	PROTECTION AND CLEANING
		A.	Immediately remove coatings that fall on surrounding areas and surfaces not scheduled to be coated.
		B.	Protect installed products until completion of project.
		C.	Touch-up, repair or replace damaged products before Substantial Completion.
		D.	Remove temporary coverings and protection of surrounding areas and surfaces.
	3.14	SCHEDULES
	** NOTE TO SPECIFIER ** Specify the coating system schedule here or on the drawings. Delete this schedule if not required.
		A.	Coating System Schedule:
	** NOTE TO SPECIFIER ** Specify the color schedule here or on the drawings. Delete this schedule if not required.
		B.	Color Schedule:
	END OF SECTION