MasterFormat: 95

SpecWizard: customize this spec    Download this Corner Guards, Wall Guards, Handrails, Protective Wall Covering, Door and Frame Protection Specification for   WORD | WP | RTF | TEXT

Find over 500 more construction specifications | Arcat.com

	SECTION 10260
	CORNER GUARDS, WALL GUARDS, HANDRAILS, PROTECTIVE WALL COVERING, DOOR AND FRAME PROTECTION
	** NOTE TO SPECIFIER ** InPro Corporation; interior protection products. . This section is based on corner guards, wall guards, handrails, protective wall covering, door and frame protection products manufactured by InPro Corporation, which is located at: P.O. Box 406 S 80 W 18766 Apollo Drive Muskego, WI 53150 Tel: 800 222-5556 Tel: 262-679-9010 Fax: 262-679-5531 E-mail address: service@inprocorp.com Website: www.inprocorp.com InPro Corporation manufactures a wide range of wall protection devices. InPro Corporation is now considered by many to be the worldwide leader in its industry, since it is the only company in the industry to manufacture all the rigid and flexible plastic products it sells. .
	PART 1	GENERAL
	1.1	SECTION INCLUDES
	** NOTE TO SPECIFIER ** Delete items below not required for project.
		A.	Surface-mounted corner guards.
		B.	Flush mounted corner guards.
		C.	Fire-rated flush mounted corner guards.
		D.	Bumper Guards.
		E.	Protective Corridor Handrails.
		F.	Protective Wall Covering.
		G.	Door and Frame Protection.
		H.	Mounting hardware, accessories, and trim.
	1.2	RELATED SECTIONS
	** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
		A.	Section 09210 - Gypsum Plaster.
		B.	Section 09260 - Gypsum Board Assemblies.
	1.3	REFERENCES
	** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
		A.	ANSI/UL 2079 - Standard for Tests for Fire Resistance of Building Joint System; 1998.
		B.	ASTM A 176 - Standard Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and Strip; 1999.
		C.	ASTM B 221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes; 2000.
		D.	ASTM D 256 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics; 2002.
		E.	ASTM D 543 - Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents; 1995(2001).
		F.	ASTM D 635 - Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position; 1998.
		G.	ASTM E 84 - Standard Test Method for Surface Burning Characteristics of Building Materials; 2001.
		H.	CAN/ULC S102.2 - Standard Method of Test for Surface Burning Characteristics of Building Materials.
		I.	SAE J-1545 - Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim; 1986.
	1.4	SUBMITTALS
		A.	Submit under provisions of Section 01300.
		B.	Product Data: Manufacturer's complete and current product data for each product required, including:
			1.	Preparation instructions and recommendations.
			2.	Storage and handling requirements and recommendations.
			3.	Complete installation methods.
		C.	Shop Drawings: Show locations of each item and installation details. Provide elevations of non-standard conditions.
		D.	Selection Samples: Color charts consisting of actual product pieces, demonstrating full range of available colors, for initial color selection.
		E.	Verification Samples: 8 inch (200 mm) long assemblies, including one end cap, in color specified.
	1.5	QUALITY ASSURANCE
		A.	Provide test reports showing compliance with the performance specified for:
			1.	Fire-related properties.
			2.	Accessibility and safety properties.
			3.	Impact strength.
	** NOTE TO SPECIFIER ** Delete paragraph below if no fire-rated flush mounted corner guards are required.
		B.	Fire Resistance: Where fire ratings are specified for flush mounted corner guards, provide assemblies meeting the requirements of ANSI/UL 2079 to maintain the rating of wall assemblies.
	** NOTE TO SPECIFIER ** Delete paragraph below if no BluNose™ high impact corner guards are required.
		C.	System Impact Resistance: Provide system capable of resisting an impact of 153.9 ft-lb (208.7 N m) while producing no visual blemishes on vinyl cover and no deformations in vinyl retainer.
	PART 2	PRODUCTS
	2.1	MANUFACTURERS
		A.	Acceptable Manufacturer: InPro Corporation, which is located at: S80 W18766 Apollo Dr. ; Muskego, WI 53150; Toll Free Tel: 800-222-5556; Tel: 262-679-9010; Email: request info; Web: www.inprocorp.com
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
		B.	Substitutions: Not permitted.
		C.	Requests for substitutions will be considered in accordance with provisions of Section 01600.
	2.2	MATERIALS
	** NOTE TO SPECIFIER ** Delete materials not used in selected products.
		A.	Vinyl: Fire retardant, high impact polyvinyl chloride (PVC), with an embossed pebbled finish.
			1.	Minimum Thickness: 0.080 inch (2.0 mm).
			2.	Vinyl Properties:
				a.	Surface burning characteristics, tested in accordance with ASTM E 84: Flame spread 10, smoke developed 350-450; maximum.
				b.	Surface burning characteristics, tested in accordance with CAN/ULC S102.2: Flame spread 15, smoke developed 35; maximum.
				c.	Self-extinguishing characteristics: CC1 classification, per ASTM D 635.
				d.	Impact strength, tested in accordance with ASTM D 256: 30.2 ft lb/inch (5285 N/m) of notch, minimum.
				e.	Chemical and stain resistant, as tested in accordance with ASTM D 543.
				f.	Fungus and bacteria resistant, as tested in accordance with ASTM G 21 and ASTM G 22.
				g.	Color consistency match when tested in accordance with SAE J-1545: Accurate to within 1.0 or less Delta E by CIE LAB 10 degree standard observer color difference and equation.
		B.	Polycarbonate/acrylonitrile butadiene styrene (PC/ABS): Provide corner guard components extruded from fire retardant, chemical and stain resistant PC/ABS, with an embossed pebbled finish.
		C.	Polycarbonate: Provide specialty surface mounted corner guards of clear polycarbonate.
		D.	Aluminum for Corner Guard Retainers: Alloy 6063-T5, in accordance with ASTM B 221; mill finish.
		E.	Stainless Steel: ASTM A 176, Type 430, 16 gauge, satin finish.
	2.3	SURFACE MOUNTED RIGID VINYL CORNER GUARDS
	** NOTE TO SPECIFIER ** Delete corner guard styles not required for project, or delete this entire article if no surface mounted corner guards of rigid vinyl are required. If more than one type is required, either schedule on drawings or add statements to specifications, describing locations for each corner guard style.
		A.	150: 3-inch (76 mm) wide, 0.80-inch (2.0 mm) thick rigid vinyl cover over continuous 0.070-inch (1.8 mm) aluminum retainer.
			1.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			2.	Color: As selected from manufacturer's standard palette of colors and patterns.
			3.	Color: ________________.
		B.	150BN: BluNose 3-inch (76 mm) wide, 0.80-inch (2.0 mm) thick rigid vinyl cover over continuous 0.070-inch (1.8 mm) vinyl retainer with co-extruded flexible vinyl apex for high impact resistance.
			1.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			2.	Color: As selected from manufacturer's standard palette of colors and patterns.
			3.	Color: ________________.
		C.	160: 2-inch (50 mm) wide, 0.080-inch (2.0 mm) thick rigid vinyl cover over continuous 0.070-inch (1.8 mm) aluminum retainer.
			1.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			2.	Color: As selected from manufacturer's standard palette of colors and patterns.
			3.	Color: ________________.
		D.	160BN: BluNose 2-inch (50 mm) wide, 0.080-inch (2.0 mm) thick rigid vinyl cover over continuous 0.070-inch (1.8 mm) vinyl retainer with co-extruded flexible vinyl apex for high impact resistance.
			1.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			2.	Color: As selected from manufacturer's standard palette of colors and patterns.
			3.	Color: ________________.
		E.	G160: 2-inch (50mm) wide, 0.080-inch (2.0mm) thick rigid PC/ABS cover over continuous 0.080 -inch (2.0mm) continuous PC/ABS aluminum retainer.
			1.	Provide top and bottom closure caps of injection-molded thermoplastics in color match PC/ABS cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			2.	Color: As selected from manufacturer's standard palette of colors and patterns.
			3.	Color: ________________.
		F.	170: 3-inch (76 mm) wide, 0.080-inch (2.0 mm) thick, bull-nosed 7/8 inch (22 mm) radius, rigid vinyl cover over continuous 0.070-inch (1.8 mm) aluminum retainer.
			1.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			2.	Color: As selected from manufacturer's standard palette of colors and patterns.
			3.	Color: ________________.
		G.	170BN: BluNose 3-inch (76 mm) wide, 0.080-inch (2.0 mm) thick, bull-nosed 7/8 inch (22 mm) radius, rigid vinyl cover over continuous 0.070-inch (1.8 mm) vinyl retainer with co-extruded flexible vinyl apex for high impact resistance.
			1.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			2.	Color: As selected from manufacturer's standard palette of colors and patterns.
			3.	Color: ________________.
		H.	130: 3-inch (76 mm) wide, 0.080-inch (2.0 mm) thick, 135 degree corner, rigid vinyl cover over continuous 0.070-inch (1.8 mm) aluminum retainer.
			1.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			2.	Color: As selected from manufacturer's standard palette of colors and patterns.
			3.	Color: ________________.
		I.	130BN: BluNose 3-inch (76 mm) wide, 0.080-inch (2.0 mm) thick, 135 degree corner, rigid vinyl cover over continuous 0.070-inch (1.8 mm) vinyl retainer with co-extruded flexible vinyl apex for high impact resistance.
			1.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			2.	Color: As selected from manufacturer's standard palette of colors and patterns.
			3.	Color: ________________.
		J.	150D: Pair of 150 corner guards with variable width vinyl filler strip for end wall protection.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Color: As selected from manufacturer's standard palette of colors and patterns.
			2.	Color: ________________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Filler Strip Color: Match corner guards.
			4.	Filler Strip Color: Contrasting color: __________.
			5.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
		K.	150DBN: Pair of 150BN BluNose corner guards with variable width vinyl filler strip for end wall protection.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Color: As selected from manufacturer's standard palette of colors and patterns.
			2.	Color: ________________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Filler Strip Color: Match corner guards.
			4.	Filler Strip Color: Contrasting color: __________.
			5.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
		L.	160D: Pair of 160 corner guards with variable width vinyl filler strip for end wall protection.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Color: As selected from manufacturer's standard palette of colors and patterns.
			2.	Color: ________________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Filler Strip Color: Match corner guards.
			4.	Filler Strip Color: Contrasting color: __________.
			5.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
		M.	160DBN: Pair of 160BN BluNose corner guards with variable width vinyl filler strip for end wall protection.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Color: As selected from manufacturer's standard palette of colors and patterns.
			2.	Color: ________________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Filler Strip Color: Match corner guards.
			4.	Filler Strip Color: Contrasting color: __________.
			5.	Provide top and bottom closure caps of injection-molded thermoplastics in color matching vinyl cover.
	2.4	SPECIALTY SURFACE MOUNTED CORNER GUARDS
	** NOTE TO SPECIFIER ** Delete corner guard styles not required for project, or delete this entire article if no specialty surface mounted corner guards are required. If more than one type is required, either schedule on drawings or add statements to specifications, describing locations for each corner guard style.
		A.	Smooth Tape-On Vinyl: 0.080-inch (2.0 mm) thick, smooth rigid vinyl for installation by adhesive or double faced tape.
	** NOTE TO SPECIFIER ** Select style requirement. Delete one of the next two paragraphs.
			1.	Style: 3/4 x 3/4 inch (19 x 19 mm), 90 degree.
			2.	Style: 1-1/2 x 1-1/2 inch (38 x 38 mm), 90 degree.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Color: As selected from manufacturer's standard palette of colors and patterns.
			4.	Color: ________________.
		B.	Textured Tape-On Vinyl: 0.080-inch (2.0 mm) thick, pebble-textured rigid vinyl for installation by adhesive or double faced tape.
	** NOTE TO SPECIFIER ** Select style requirement. Delete five of the next six paragraphs.
			1.	Style: 3/4 x 3/4 inch (19 x 19 mm), 90 degree.
			2.	Style: 1-1/2 x 1-1/2 inch (38 x 38 mm), 90 degree.
			3.	Style: 1-1/2 x 1-1/2 inch (38 x 38 mm), 135 degree.
			4.	Style: 2 x 2 inch (50 x 50 mm), 90 degree bullnose.
			5.	Style: 3 x 3 inch (76 mm x 76 mm), 90 degree.
			6.	Style: 3 x 3 inch (76 mm x 76 mm), 135 degree.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			7.	Color: As selected from manufacturer's standard palette of colors and patterns.
			8.	Color: ________________.
		C.	180: 3-1/2 x 3-1/2-inch (89 x 89 mm) wide, 16 gauge Type 430 stainless steel, 90 degree corner with 1/8-inch (3.2 mm) radius, for adhesive installation.
		D.	181: 3-1/2 x 3-1/2-inch (89 x 89 mm) wide, 16 gauge Type 430 stainless steel, 90 degree corner with 3/4-inch (19 mm) radius, for adhesive installation.
		E.	180GS: 3-1/2 x 3-1/2-inch (89 x 89 mm) wide, 18 gauge Type 304 gold titanium stainless steel, 90 corner with 1/8-inch (3.2mm) radius, for adhesive installation.
		F.	182GS: 1-1/2 x 1-1/2-inch (38 x 38 mm) wide, 18 gauge Type 304 gold titanium stainless steel, 90 corner with 1/8-inch (3.2mm) radius, for adhesive installation.
		G.	Flexible Vinyl: 0.110-inch (2.8 mm) thick, smooth flexible vinyl for installation by adhesive.
	** NOTE TO SPECIFIER ** Select style requirement. Delete one of the next two paragraphs.
			1.	Style: 3/4 x 3/4 inch (19 x 19 mm), 90 degree.
			2.	Style: 3/4 x 3/4 inch (19 x 19 mm), 135 degree
			3.	Style: 1-1/2 x 1-1/2 inch (38 x 38 mm), 90 degree.
			4.	Style: 1-1/2 x 1-1/2 inch (38 x 38 mm), 135 degree.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			5.	Color: As selected from manufacturer's standard palette of colors and patterns.
			6.	Color: ________________.
		H.	Heavy-Duty Rubber: 4 x 4-inch (100 x 100mm) wide, rubber, 90 degree corner for installation by exposed fasteners.
		I.	Clear Polycarbonate:
	** NOTE TO SPECIFIER ** Select style requirement. Delete three of the next four paragraphs.
			1.	Style: 3/4 x 3/4 inch (19 x 19 mm), 0.050 inch (1.3 mm) thickness, 90 degree corner for installation with self-tapping nail screws.
			2.	Style: 1-1/8 x 1-1/8 inch (28 x 28 mm), 0.075 inch (1.9 mm) thickness, 90 degree corner for installation with chrome-plated screws.
			3.	Style: 2-1/2 x 2-1/2 inch (63.5 x 63.5 mm), 0.10 inch (2.5 mm) thickness, 90 degree corner for installation with chrome-plated screws.
			4.	Style: 2-1/2 x 2-1/2 inch (63.5 x 63.5 mm), 0.10 inch (2.5 mm) thickness, 135 degree corner for installation with chrome-plated screws.
	2.5	FLUSH MOUNTED RIGID VINYL CORNER GUARDS
	** NOTE TO SPECIFIER ** Delete corner guard styles not required for project, or delete this entire article if no flush mounted corner guards are required. If more than one type is required, either schedule on drawings or add statements to specifications, describing locations for each corner guard style.
		A.	150F: 3-inch (76 mm) wide, 0.080-inch (2.0 mm) thick, 90 degree textured rigid vinyl cover over continuous 0.070-inch (1.8 mm) aluminum retainer, configured for flush installation on gypsum wallboard.
	** NOTE TO SPECIFIER ** The two paragraphs below are options. Delete if not required.
			1.	Cove Base Retainer: Fabricate from 6063-T5 aluminum with mill finish.
			2.	Closure Cap: Fabricate from 0.35 inch (0.8 mm) aluminum.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Color: As selected from manufacturer's standard palette of colors and patterns.
			4.	Color: ________________.
		B.	150FR: 3-inch (76 mm) wide, 0.080-inch (2.0 mm) thick, 90 degree textured rigid vinyl cover and foil covered fiber fire barrier over continuous 0.070-inch (1.8 mm) aluminum retainer, configured for flush installation on gypsum wallboard.
	** NOTE TO SPECIFIER ** Delete one of the following two fire ratings.
			1.	Fire Rating: One hour.
			2.	Fire Rating: Two hours.
			3.	Steel Angle: Galvanized 22 gauge steel angle, with 3-1/8 inch (79 mm) wings, for installation below corner guard.
	** NOTE TO SPECIFIER ** The paragraph below is an option. Delete if not required.
			4.	Cove Base Retainer: Fabricate from 6063-T5 aluminum with mill finish.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			5.	Color: As selected from manufacturer's standard palette of colors and patterns.
			6.	Color: ________________.
		C.	160F: 2-inch (50 mm) wide, 0.080-inch (2.0 mm) thick, 90 degree textured rigid vinyl cover over continuous 0.070-inch (1.8 mm) aluminum retainer, configured for flush installation on gypsum wallboard.
	** NOTE TO SPECIFIER ** The two paragraphs below are options. Delete if not required.
			1.	Cove Base Retainer: Fabricate from 6063-T5 aluminum with mill finish.
			2.	Closure Cap: Fabricate from 0.35 inch (0.8 mm) aluminum.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Color: As selected from manufacturer's standard palette of colors and patterns.
			4.	Color: ________________.
		D.	160FR: 2-inch (50 mm) wide, 0.080-inch (2.0 mm) thick, 90 degree textured rigid vinyl cover and foil covered fiber fire barrier over continuous 0.070-inch (1.8 mm) aluminum retainer, configured for flush installation on gypsum wallboard.
	** NOTE TO SPECIFIER ** Delete one of the following two fire ratings.
			1.	Fire Rating: One hour.
			2.	Fire Rating: Two hours.
			3.	Steel Angle: Galvanized 22 gauge steel angle, with 2-1/8 inch (54 mm) wings, for installation below corner guard.
	** NOTE TO SPECIFIER ** The paragraph below is an option. Delete if not required.
			4.	Cove Base Retainer: Fabricate from 6063-T5 aluminum with mill finish.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			5.	Color: As selected from manufacturer's standard palette of colors and patterns.
			6.	Color: ________________.
		E.	170F: 3-inch (76 mm) wide, 0.080-inch (2.0 mm) thick, bullnosed 90 degree textured rigid vinyl cover over continuous 0.070-inch (1.8 mm) aluminum retainer, configured for flush installation on gypsum wallboard.
	** NOTE TO SPECIFIER ** The two paragraphs below are options. Delete if not required.
			1.	Cove Base Retainer: Fabricate from 6063-T5 aluminum with mill finish.
			2.	Closure Cap: Fabricate from 0.35 inch (0.8 mm) aluminum.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Color: As selected from manufacturer's standard palette of colors and patterns.
			4.	Color: ________________.
		F.	170FR: 3-inch (76 mm) wide, 0.080-inch (2.0 mm) thick, bullnosed 90 degree textured rigid vinyl cover and foil covered fiber fire barrier over continuous 0.070-inch (1.8 mm) aluminum retainer, configured for flush installation on gypsum wallboard.
	** NOTE TO SPECIFIER ** Delete one of the following two fire ratings.
			1.	Fire Rating: One hour.
			2.	Fire Rating: Two hours.
			3.	Steel Angle: Galvanized 22 gauge steel angle, with 3-1/8 inch (79 mm) wings, for installation below corner guard.
	** NOTE TO SPECIFIER ** The paragraph below is an option. Delete if not required.
			4.	Cove Base Retainer: Fabricate from 6063-T5 aluminum with mill finish.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			5.	Color: As selected from manufacturer's standard palette of colors and patterns.
			6.	Color: ________________.
		G.	130F: 3-inch (76 mm) wide, 0.080-inch (2.0 mm) thick, 135 degree textured rigid vinyl cover over continuous 0.084-inch (2.1 mm) aluminum retainer, configured for flush installation on gypsum wallboard.
	** NOTE TO SPECIFIER ** The two paragraphs below are options. Delete if not required.
			1.	Cove Base Retainer: Fabricate from 6063-T5 aluminum with mill finish.
			2.	Closure Cap: Fabricate from 0.35 inch (0.8 mm) aluminum.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Color: As selected from manufacturer's standard palette of colors and patterns.
			4.	Color: ________________.
		H.	130FR: 3-inch (76 mm) wide, 0.080-inch (2.0 mm) thick, 135 degree textured rigid vinyl cover and foil covered fiber fire barrier over continuous 0.084-inch (2.1 mm) aluminum retainer, configured for flush installation on gypsum wallboard.
	** NOTE TO SPECIFIER ** Delete one of the following two fire ratings.
			1.	Fire Rating: One hour.
			2.	Fire Rating: Two hours.
			3.	Steel Angle: Galvanized 22 gauge steel angle, with 3-1/8 inch (79 mm) wings, for installation below corner guard.
	** NOTE TO SPECIFIER ** The paragraph below is an option. Delete if not required.
			4.	Cove Base Retainer: Fabricate from 6063-T5 aluminum with mill finish.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			5.	Color: As selected from manufacturer's standard palette of colors and patterns.
			6.	Color: ________________.
		I.	140D: Flush end wall protection with 2-inch (50 mm) return, 0.080-inch thick, textured rigid vinyl cover over two 0.070-inch aluminum retainers at outside corners, configured for flush installation on gypsum wallboard.
	** NOTE TO SPECIFIER ** Vinyl cover is custom fabricated to width of wall. Total width of wall may not exceed 12 inches (305 mm). Enter required width below, or delete paragraph below and show multiple widths on the drawings.
			1.	Width of Wall: ___________.
			2.	Width of Walls: As indicated on the drawings.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Color: As selected from manufacturer's standard palette of colors and patterns.
			4.	Color: ________________.
		J.	SS-CGFM: Custom size, 16 gauge Type 430 stainless steel, 90 degree corner, for installation with fasteners.
		K.	SS-EWFM: Custom size, 16 gauge Type 430 stainless steel, flush end wall protection, for installation with fasteners.
	2.6	BUMPER GUARDS
	** NOTE TO SPECIFIER ** Delete bumper guard styles not required for project, or delete this entire article if none are required. If more than one type is required, either schedule on drawings or add statements to specifications, describing locations for each style.
		A.	200: 1-1/8 inch (28mm) high aluminum and vinyl wall guard system with 1-1/8 inch (28mm) projection from the wall. Wall guard shall have radius top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
		B.	500: 3 inch (76mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have radius top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
		C.	1300: 4-1/16 inch (103mm) high aluminum and vinyl wall guard system with 1-7/8 inch (48mm) projection from the wall. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
		D.	1400: 4 inch (102mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have radius top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
		E.	1455: 4 inch (102mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall and a co-extruded or co-laminated accent strip. Wall guard shall have radius top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and vinyl cover shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Color: As selected from manufacturer's standard palette of colors and patterns.
			2.	Color: ________________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Accent strip color: as selected from the manufacturer's accent strip color palette.
			4.	Accent strip color: __________.
		F.	1400i: 4 inch (102mm) high aluminum retainer clip and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have radius top and bottom edges. Aluminum retainer clips shall be 2 inch (51mm) wide and .080 inch (2mm) thick. Vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		G.	1455i: 4 inch (102mm) high aluminum retainer clip and vinyl wall guard system with 1 inch (25mm) projection from the wall and a co-extruded or co-laminated accent strip. Wall guard shall have radius top and bottom edges. Aluminum retainer clips shall be 2 inch (51mm) wide and .080 inch (2mm) thick. Vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Accent strip color: as selected from the manufacturer's accent strip color palette.
			4.	Accent strip color: __________.
		H.	1600: 6 inch (152mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have radius top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		I.	1655: 6 inch (152mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall and a co-extruded or co-laminated accent strip. Wall guard shall have radius top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Accent strip color: as selected from the manufacturer's accent strip color palette.
			4.	Accent strip color: __________.
		J.	1600i: 6 inch (152mm) high aluminum retainer clip and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have radius top and bottom edges. Aluminum retainer clips shall be 2 inch (51mm) wide and .080 inch (2mm) thick. Vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		K.	1655i: 6 inch (152mm) high aluminum retainer clip and vinyl wall guard system with 1 inch (25mm) projection from the wall and a co-extruded or co-laminated accent strip. Wall guard shall have radius top and bottom edges. Aluminum retainer clips shall be 2 inch (51mm) wide and .080 inch (2mm) thick. Vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Accent strip color: as selected from the manufacturer's accent strip color palette.
			4.	Accent strip color: __________.
		L.	700: 7-3/4 inch (196mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have radius top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		M.	700i: 7-3/4 inch (197mm) high aluminum retainer clip and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have radius top and bottom edges. Aluminum retainer clips shall be 2 inch (51mm) wide and .080 inch (2mm) thick. Vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		N.	700W: 7-3/4 inch (196mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall and a co-laminated wood grain pattern. Wall guard shall have radius top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color/pattern matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl colors/pattern: As selected from the manufacturer's woodland color palette.
			2.	Vinyl colors/pattern: __________.
		O.	700iW: 7-3/4 inch (197mm) high aluminum retainer clip and vinyl wall guard system with 1 inch (25mm) projection from the wall and a co-laminated wood grain pattern. Wall guard shall have radius top and bottom edges. Aluminum retainer clips shall be 2 inch (51mm) wide and .080 inch (2mm) thick. Vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl colors/pattern: As selected from the manufacturer's woodland color palette.
			2.	Vinyl colors/pattern: __________.
		P.	1800: 8 inch (204mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have distinctive silhouette shape. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		Q.	1800i: 8 inch (204mm) high aluminum retainer clip and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have distinctive silhouette shape. Aluminum retainer clips shall be 2-inch (50mm) wide and .080 inch (2mm) thick. Vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		R.	2500: 2 inch (50mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have half round profile. Aluminum retainer shall be .060 inch (1.5mm) thick and vinyl shall be .070 inch (1.8mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		S.	2600: 3 inch (76mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have transitional shaped profile. Aluminum retainer shall be .060 inch (1.5mm) thick and vinyl shall be .070 inch (1.8mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		T.	2700: 3 inch (76mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have traditional shaped profile. Aluminum retainer shall be .060 inch (1.5mm) thick and vinyl shall be .070 inch (1.8mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		U.	2700W: 3 inch (76mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall and a co-laminated wood grain pattern.. Wall guard shall have traditional shaped profile. Aluminum retainer shall be .060 inch (1.5mm) thick and vinyl shall be .070 inch (1.8mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color/pattern matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl colors/pattern: As selected from the manufacturer's woodland color palette.
			2.	Vinyl colors/pattern: __________.
		V.	5000: 4 inch (102mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have chiseled top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		W.	5055: 4 inch (102mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall and a co-extruded or co-laminated accent strip.. Wall guard shall have chiseled top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Accent strip color: as selected from the manufacturer's accent strip color palette.
			4.	Accent strip color: __________.
		X.	5000i: 4 inch (102mm) high aluminum retainer clip and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have chiseled top and bottom edges. Aluminum retainer clips shall be 2 inch (51mm) wide and .080 inch (2mm) thick. Vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		Y.	5055i: 4 inch (102mm) high aluminum retainer clip and vinyl wall guard system with 1 inch (25mm) projection from the wall and a co-extruded or co-laminated accent strip. Wall guard shall have chiseled top and bottom edges. Aluminum retainer clips shall be 2 inch (51mm) wide and .080 inch (2mm) thick. Vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Accent strip color: as selected from the manufacturer's accent strip color palette.
			4.	Accent strip color: __________.
		Z.	1500: 5 inch (127mm) high aluminum and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have distinctive silhouette shape. Aluminum retainer shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		AA.	1500i: 5 inch (127mm) high aluminum retainer clip and vinyl wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have distinctive silhouette shape. Aluminum retainer clips shall be 2-inch (50mm) wide and .080 inch (2mm) thick. Vinyl shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		AB.	G5000: 4 inch (101mm) high wood retainer and polycarbonate/acrylonitrile butadiene styrene (PC/ABS)wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have chiseled top and bottom edges. Wood shall be Forest Stewardship Council (FSC) certified and PC/ABS shall be .080 inch (2.0mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	PC/ABS color: As selected from the manufacturer's color palette.
			2.	PC/ABS color: __________.
		AC.	G5100: 4 inch (101mm) high wood retainer and polycarbonate/acrylonitrile butadiene styrene (PC/ABS) wall guard system with 1 inch (25mm) projection from the wall and a wood stained accent on the top edge. Wall guard shall have chiseled top and bottom edges. Wood shall be Forest Stewardship Council (FSC) certified and PC/ABS shall be .080 inch (2.0mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	PC/ABS color: As selected from the manufacturer's color palette.
			2.	PC/ABS color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Wood stain color: As selected from the manufacturer's wood stain color palette.
			4.	Wood stain color: __________.
		AD.	G700: 7-3/4 inch (196mm) high aluminum and non-PVC wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have radius top and bottom edges. Aluminum retainer shall be .080 inch (2mm) thick and non-PVC shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the non-PVC cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Non-PVC color: As selected from the manufacturer's non-PVC color palette.
			2.	Non-PVC color: __________.
		AE.	G700i: 7-3/4 inch (197mm) high aluminum retainer clip and non-PVC wall guard system with 1 inch (25mm) projection from the wall. Wall guard shall have radius top and bottom edges. Aluminum retainer clips shall be 2 inch (51mm) wide and .080 inch (2mm) thick. Non-PVC shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the non-PVC cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Non-PVC color: As selected from the manufacturer's color palette.
			2.	Non-PVC color: __________.
		AF.	6000: 3-1/2 inch (89mm) high aluminum and vinyl bed locator system with 3-1/2 inch (89mm) projection from the wall. Bed Locator shall have sculpted profile. Aluminum retainer shall be .080 inch (2mm) thick and vinyl cover shall be .080 inch (2mm) thick. End caps shall serve as bed locating guides and project 7 3/8 inch (187mm) from the wall. Provide end caps of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		AG.	MB10 Cartguard: 1 1/8 inch (28mm) high vinyl retainer and flexible vinyl wall guard system with 7/8 inch (22mm) projection from the wall. Wall guard shall have half round appearance. Vinyl retainer shall be .050 inch (1.3mm) thick and vinyl cover shall be .175 inch (4.4mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover. Cover and molded components shall have a smooth gloss appearance.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Cartguard color: As selected from the manufacturer's Cartguard color palette.
			2.	Cartguard color: __________.
		AH.	MB20 Cartguard: 2 inch (28mm) high vinyl retainer and flexible vinyl wall guard system with 1 1/8 inch (29mm) projection from the wall. Wall guard shall have half round appearance. Vinyl retainer shall be .060 inch (1.5mm) thick and vinyl cover shall be 0.175 inch (4.4mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover. Cover and molded components shall have a smooth gloss appearance.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Cartguard color: As selected from the manufacturer's Cartguard color palette.
			2.	Cartguard color: __________.
		AI.	83: 3 inch (76mm) high polycarbonate wall guard with 5/16 inch (8mm) projection from the wall. Wall guard shall be clear with a gloss finish.
		AJ.	84: 4 inch (102mm) high polycarbonate wall guard with 5/16 inch (8mm) projection from the wall. Wall guard shall be clear with a gloss finish.
		AK.	30SS: 5-1/2 inch (140mm) high stainless steel wall guard system with 1-1/2 inch (38mm) projection from the wall. Wall guard shall have angled top and bottom edges. Wall guard shall be fabricated provided measurements.
		AL.	50AA: 4 inch (102mm) high aluminum wall guard system with a 3-1/4 inch (83mm) projection from the wall. Provide wall guard system with aluminum mounting brackets that have no visible mounting fasteners. End conditions and corner shall be fabricated in a finish matching that of the straight sections.
		AM.	50SS: 4 inch (102mm) high stainless steel wall guard system with a 3-5/16 inch (85mm) projection from the wall. Provide wall guard system with aluminum mounting brackets that have no visible mounting fasteners. End conditions and corner shall be fabricated in a finish matching that of the straight sections.
		AN.	CR-1: 3-1/2 inch (89 mm) wood chair rail system with 5/8 inch (16mm) projection from the wall. Chair rail shall have exclusively shaped profile. Wood shall be oak, maple or bamboo.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Wood chair rail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Wood chair rail stain color: __________.
		AO.	CR-2: 3-1/2 inch (89mm), wood, vinyl and aluminum chair rail system with 1-1/2 inch (38mm) projection from the wall and a 1 1/8 inch (28mm) bumper guard integrated into the chair rail. Wood shall be oak or maple. Bumper guard shall have an aluminum retainer 080 inch (2mm) thick and vinyl cover shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Wood chair rail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Wood chair rail stain color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Bumper guard color: As selected from the manufacturer's color palette.
			4.	Bumper guard vinyl color: __________.
		AP.	CR-3: 3-1/2 inch (89mm), wood, vinyl and aluminum chair rail system with 1-3/8 inch (35mm) projection from the wall and a 2 inch (25mm) bumper guard integrated into the chair rail. Wood shall be oak or maple. Bumper guard shall have an aluminum retainer 060 inch (1.5mm) thick and vinyl cover shall be .070 inch (1.8mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Wood chair rail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Wood chair rail stain color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Bumper guard color: As selected from the manufacturer's color palette.
			4.	Bumper guard vinyl color: __________.
		AQ.	NT-180: 6 inch (152mm), high-density polyethylene wall guard system with 1/2 inch (13mm) projection from the wall. High-density polyethylene manufactured from recycled No. 2 plastic containers.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	High-density polyethylene wall guard color: As selected from the manufacturer's Nu-Tree color palette.
			2.	High-density polyethylene color: __________.
		AR.	NT-140: 8 inch (203mm), high-density polyethylene wall guard system with 1/2 inch (13mm) projection from the wall. High-density polyethylene manufactured from recycled No. 2 plastic containers.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	High-density polyethylene wall guard color: As selected from the manufacturer's Nu-Tree color palette.
			2.	High-density polyethylene color: __________.
		AS.	NT-250: 3-1/2 inch (89mm), high-density polyethylene wall guard system with 3/4 inch (19mm) projection from the wall. High-density polyethylene manufactured from recycled No. 2 plastic containers.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	High-density polyethylene wall guard color: As selected from the manufacturer's Nu-Tree color palette.
			2.	High-density polyethylene color: __________.
		AT.	NT-518: 5-1/2 inch (140mm), high-density polyethylene wall guard system with 1 inch (25mm) projection from the wall. High-density polyethylene manufactured from recycled No. 2 plastic containers.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	High-density polyethylene wall guard color: As selected from the manufacturer's Nu-Tree color palette.
			2.	High-density polyethylene color: __________.
		AU.	NT-690: 5-1/2 inch (140mm), high-density polyethylene wall guard system with 1-1/2 inch (38mm) projection from the wall. High-density polyethylene manufactured from recycled No. 2 plastic containers.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	High-density polyethylene wall guard color: As selected from the manufacturer's Nu-Tree color palette.
			2.	High-density polyethylene color: __________.
		AV.	NT-694: 7-1/2 inch (198mm), high-density polyethylene wall guard system with 1-1/2 inch (38mm) projection from the wall. High-density polyethylene manufactured from recycled No. 2 plastic containers.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	High-density polyethylene wall guard color: As selected from the manufacturer's Nu-Tree color palette.
			2.	High-density polyethylene color: __________
		AW.	NT-695: 9-1/2 inch (241mm), high-density polyethylene wall guard system with 1-1/2 inch (38mm) projection from the wall. High-density polyethylene manufactured from recycled No. 2 plastic containers.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	High-density polyethylene wall guard color: As selected from the manufacturer's Nu-Tree color palette.
			2.	High-density polyethylene color: __________.
		AX.	D-Fender: 4-1/4 inch (107mm), rubber wall guard system with 3-3/4 inch (95mm) projection from the wall. Color: Black.
		AY.	E-Fender: 6 inch (150mm), rubber wall guard system with 1 1/8 inch (30mm) projection from the wall. Color: Black.
		AZ.	E-Fender: 8 inch (200mm), rubber wall guard system with 1 1/8 inch (30mm) projection from the wall. Color: Black.
	2.7	HANDRAILS
		A.	800: Provide 5-1/2 inch (140mm) high aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		B.	855: Provide 5-1/2 inch (140mm) high aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and a 1-1/2 inch (38mm) standoff from the wall and a co-extruded or co-laminated accent strip. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover base color.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Accent strip color: as selected from the manufacturer's color palette.
			4.	Accent strip color __________.
		C.	800W: Provide 5-1/2 inch (140mm) high aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and a 1-1/2 inch (38mm) standoff from the wall and a co-laminated wood grain pattern. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover base color.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's woodland color palette.
			2.	Vinyl color: __________.
		D.	1100: Provide 5-1/4 inch (133mm) high aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		E.	1200: Provide 6-1/4 inch (159mm) high aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		F.	1255: Provide 6-1/4 inch (159mm) high aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and a 1-1/2 inch (38mm) standoff from the wall and a co-extruded or co-laminated accent strip. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover base color.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Accent strip color: as selected from the manufacturer's accent strip color palette.
			4.	Accent strip color __________.
		G.	900: Provide aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		H.	2000: Provide aluminum and vinyl handrail system with 1-1/2 inch (38mm) x 2-1/4 inch (57mm) gripping surface and 1-1/2 inch (38mm) standoff from the wall. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		I.	2000W: Provide aluminum and vinyl handrail system with 1-1/2 inch (38mm) x 2-1/4 inch (57mm) gripping surface and 1-1/2 inch (38mm) standoff from the wall and a co-laminated wood grain pattern. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's woodland color palette.
			2.	Vinyl color: __________.
		J.	4000: Provide aluminum and vinyl handrail system with 1-1/2 inch (38mm) x 2 inch (51mm) gripping surface and 1-1/2 inch (38mm) standoff from the wall. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Vinyl color: As selected from the manufacturer's color palette.
			2.	Vinyl color: __________.
		K.	3000: Provide 6-1/8 inch (155mm) high aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Handrail system shall include 4 inch vinyl bumper guard below gripping surface with inner impact bumper. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Handrail vinyl color: As selected from the manufacturer's color palette.
			2.	Handrail vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Bumper guard color: As selected from the manufacturer's color palette.
			4.	Bumper guard vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			5.	Thumb insert color: As selected from the manufacturer's thumb insert color palette.
			6.	Thumb insert color: __________.
		L.	3055: Provide 6-1/8 inch (155mm) high aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Handrail system shall include 4 inch vinyl bumper guard below gripping surface with inner impact bumper and a co-extruded or co-laminated accent strip. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Handrail vinyl color: As selected from the manufacturer's color palette.
			2.	Handrail vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Bumper guard color: As selected from the manufacturer's color palette.
			4.	Bumper guard vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			5.	Accent strip color: as selected from the manufacturer's Accent strip color palette.
			6.	Accent strip color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			7.	Thumb insert color: As selected from the manufacturer's thumb insert color palette.
			8.	Thumb insert color: __________.
		M.	3000W: Provide 6-1/8 inch (155mm) high wood, aluminum and vinyl handrail system with an oak or maple hardwood rail that has a 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Handrail system shall include 4 inch vinyl bumper guard below gripping surface with inner impact bumper. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Wood handrail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Wood handrail stain color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Bumper guard color: As selected from the manufacturer's color palette.
			4.	Bumper guard vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			5.	Thumb insert color: As selected from the manufacturer's thumb insert color palette.
			6.	Thumb insert color: __________.
		N.	3055W: Provide 6-1/8 inch (155mm) high wood, aluminum and vinyl handrail system with an oak or maple hardwood rail that has a 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Handrail system shall include 4 inch vinyl bumper guard below gripping surface with inner impact bumper and a co-extruded or co-laminated accent strip. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Wood handrail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Wood handrail stain color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Bumper guard color: As selected from the manufacturer's color palette.
			4.	Bumper guard vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			5.	Accent strip color: as selected from the manufacturer's Accent strip color palette.
			6.	Accent strip color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			7.	Thumb insert color: As selected from the manufacturer's thumb insert color palette.
			8.	Thumb insert color: __________.
		O.	3500: Provide 7-7/8 inch (200mm) high aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Handrail shall be mounted on brushed stainless steel vertical projections spaced a maximum of 32 inch (813mm) on center. Handrail system shall include 5 inch (127mm) vinyl bumper guard below gripping surface with inner impact bumper. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Handrail vinyl color: As selected from the manufacturer's color palette.
			2.	Handrail vinyl color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Bumper guard color: As selected from the manufacturer's color palette.
			4.	Bumper guard vinyl color: __________.
		P.	3500W: Provide 7-7/8 inch (200mm) high wood, aluminum and vinyl handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Oak or maple hardwood rail shall be mounted on brushed stainless steel vertical projections spaced a maximum of 32 inch (813mm) on center. Handrail system shall include 5 inch (127mm) vinyl bumper guard below gripping surface with inner impact bumper. Aluminum shall be .080 inch (2mm) thick and vinyl shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover. Optional stainless steel handrail returns and corners are available.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Wood handrail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Wood handrail stain color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Bumper guard color: As selected from the manufacturer's color palette.
			4.	Bumper guard vinyl color: __________.
		Q.	HR1: Provide 5-1/2 inch (140mm) high wood handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Wood shall be oak, maple or bamboo. Provide returns, inside and outside corner of wood matching that of the handrail.
			1.	Wood handrail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Handrail wood stain color: __________.
		R.	HR2: Provide 5-1/2 inch (140mm) high wood, vinyl and aluminum handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall and a 1-1/8 inch (28mm) bumper guard integrated into the handrail below the gripping surface. Wood shall be oak or maple. Provide returns, inside and outside corner of wood matching that of the handrail. Bumper guard shall have an aluminum retainer 080 inch (2mm) thick and vinyl cover shall be .080 inch (2mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Wood handrail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Wood handrail stain color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Bumper guard color: As selected from the manufacturer's color palette.
			4.	Bumper guard vinyl color: __________.
		S.	HR3: Provide 5-1/2 inch (140mm) high wood, vinyl and aluminum handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall and a 2 inch (50mm) bumper guard integrated into the handrail below the gripping surface. Wood shall be oak or maple. Provide returns, inside and outside corner of wood matching that of the handrail. Bumper guard shall have an aluminum retainer 060 inch (1.5mm) thick and vinyl cover shall be .070 inch (1.8 mm) thick. Provide end caps, inside and outside corner of injection molded thermoplastic in a color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Wood handrail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Wood handrail stain color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Bumper guard color: As selected from the manufacturer's color palette.
			4.	Bumper guard vinyl color: __________.
		T.	HR9: Provide wood handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Wood shall be oak, maple or bamboo. Provide returns, inside and outside corner of wood matching the handrail. Optional stainless steel handrail returns, corners and splices are available. Brackets shall be stainless steel or injection molded thermoplastic.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Wood handrail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Wood handrail stain color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Molded plastic bracket color: As selected from the manufacturer's color palette.
			4.	Molded plastic bracket color: __________.
		U.	G800: Provide 5-1/2 inch (140mm) high aluminum and non-PVC handrail system with 1-1/2 inch (38mm) gripping diameter and 1-1/2 inch (38mm) standoff from the wall. Aluminum shall be .080 inch (2mm) thick and non-PVC covers shall be .080 inch (2mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Non-PVC color: As selected from the manufacturer's color palette.
			2.	Non PVC color: __________.
		V.	G4000: Provide wood retainer and polycarbonate/acrylonitrile butadiene styrene (PC/ABS)handrail system with 1-1/2 inch (38mm) x 2 inch (51mm) gripping surface and 1-1/2 inch (38mm) standoff from the wall. Wood shall be Forest Stewardship Council (FSC) certified and PC/ABS shall be .080 inch (2.0mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	PC/ABS color: As selected from the manufacturer's color palette.
			2.	PC/ABS color: __________.
		W.	G4100: Provide wood retainer and polycarbonate/acrylonitrile butadiene styrene (PC/ABS)handrail system with 1-1/2 inch (38mm) x 2 inch (51mm) gripping surface and 1-1/2 inch (38mm) standoff from the wall that includes a stained wood accent reveal. Wood shall be Forest Stewardship Council (FSC) certified and PC/ABS shall be .080 inch (2.0mm) thick. Provide returns, inside and outside corner of injection molded thermoplastic in a color matching the cover.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	PC/ABS color: As selected from the manufacturer's color palette.
			2.	PC/ABS color: __________.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			3.	Wood stain color: As selected from the manufacturer's wood stain color palette.
			4.	Wood stain color: __________.
		X.	L1: Provide 5 inch (127mm) high wood leaning rail system with 3 inch (76mm) support ledge and a 3-5/8 inch (92mm) projection from the wall. Wood shall be oak or maple. Corners and end conditions are field fabricated.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			1.	Wood leaning rail stain color: As selected from the manufacturer's wood stain color palette.
			2.	Leaning rail stain color: __________.
	2.8	PROTECTIVE WALL COVERING
		A.	Wall Covering: Sanparrel rigid poly vinyl chloride sheet
			1.	Texture: Hair cell pattern.
			2.	Surface Burning Characteristics: Provide UL Classified Sanparrel Rigid Vinyl Sheet conforming with the NFPA Class A fire rating. Surface burning characteristics as determined by UL-723 (ASTM E-84), for Sanparrel Rigid Vinyl Sheet installed with 3M Fastbond 30, InPro Bond Adhesive, or Formulated Solutions, LLC inchXT- 2000+ inch Adhesive shall be a maximum flame spread of 20 and a maximum smoke developed of 350 for .060 inch (1.5mm) thick material. Provide ULC (Canada) listed Sanparrel Rigid Vinyl Sheet conforming to the requirements of the National Building Code of Canada 1990, Subsection 3.1.13. Surface burning characteristics, as determined by CAN/ULC-S102.2, shall be flame spread of 15 and smoke developed of 30.
			3.	Self Extinguishing: Provide rigid vinyl sheet with a CC1 classification, as tested in accordance with the procedures specified in ASTM D-635-74, Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Self-Supporting Plastics in a Horizontal Position, as referenced in UBC 52-4-1988.
			4.	Provide sheet materials that have been tested and results filed in compliance with article 15, part 1120 of the New York State uniform fire prevention and building code. DOS # 09960-930504-4001.
			5.	Impact Strength: Provide Sanparrel Rigid Vinyl Sheet that has an Impact Strength of 30.4 ft-lbs/ inch of thickness as tested in accordance with the procedures specified in ASTM D-256-90b, Impact Resistance of Plastics.
			6.	Chemical and Stain Resistance: Provide rigid vinyl sheet that show resistance to stain when tested in accordance with applicable provisions of ASTM D-543.
			7.	Fungal and Bacterial Resistance: Provide rigid vinyl that does not support fungal or bacterial growth as tested in accordance with ASTM G-21 and ASTM G-22.
	** NOTE TO SPECIFIER ** Select sheet size. Delete three of the next four paragraphs.
			8.	Sheet Size: 36 inches x 96 inches (914x2438mm).
			9.	Sheet Size: 48 inches x 96 inches (1219 x2438mm).
			10.	Sheet Size: 36 inches x 120 inches (914x3048mm).
			11.	Sheet Size: 48 inches x 120 inches (1219 x3048mm).
	** NOTE TO SPECIFIER ** Select thickness. Delete three of the next four paragraphs.
			12.	Thickness: .030 inches (0.8mm).
			13.	Thickness: .040 inches (1mm).
			14.	Thickness: .060 inches (1.5mm).
			15.	Thickness: .080 inches (2mm).
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			16.	Color: As selected from manufacturer's standard colors.
			17.	Color:______________.
			18.	Color Consistency: Provide components matched in accordance with SAE J-1545 - (Delta E) with a color difference no greater than 1.0 units using CIE Lab, CIE CMC, CIE LCh, Hunter Lab or similar color space scale systems.
		B.	Wall Covering: Sanparrel GT PC/ABS rigid sheet.
			1.	Texture: Hair cell pattern.
			2.	Surface Burning Characteristics: Provide UL Classified Sanparrel GT Sheet conforming with the NFPA Class A fire rating. Surface burning characteristics as determined by ASTM E-84, for Sanparrel GT Sheet installed with 3M Fastbond 30, or InPro Bond Adhesive shall be a maximum of 25 and a maximum smoke developed of 300 for .060 inch (1.5mm) sheet material.
			3.	Chemical and Stain Resistance: Provide rigid PC/ABS sheet that show resistance to stain when tested in accordance with applicable provisions of ASTM D-543.
			4.	Fungal and Bacterial Resistance: Provide rigid PC/ABS sheet that does not support fungal or bacterial growth as tested in accordance with ASTM G-21 and ASTM G-22.
			5.	Sheet Size: 48 inches x 96 inches (1219x2438mm).
	** NOTE TO SPECIFIER ** Select thickness. Delete one of the next two paragraphs.
			6.	Thickness: .040 inch (1mm).
			7.	Thickness: .060 inch (1.5mm).
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			8.	Color: As selected from manufacturer's standard colors.
			9.	Color: _________________.
			10.	Color Consistency: Provide components matched in accordance with SAE J-1545- (Delta E) with a color difference no greater than 1.0 units using CIE Lab, CIE CMC, CIE LCh, Hunter Lab or similar color space scale systems.
		C.	Trim: Provide trim components in the same color matching the wall covering, for use with .030 inch (0.8mm), .040 inch (1mm) and .060 inch (1.5mm) thick sheet.
			1.	Top Caps.
			2.	Vertical divider bars.
			3.	Inside corners.
			4.	Outside corner.
			5.	Color matched caulk.
		D.	Trim: Provide trim components in the same color matching the wall covering, for use with .080 inch thick sheet.
			1.	Top Caps.
			2.	Vertical divider bars.
			3.	Inside corners.
			4.	Outside corner.
			5.	Color matched caulk.
		E.	Adhesives: As recommended by manufacturer of rigid vinyl sheet.
	2.9	DOOR AND FRAME PROTECTION
		A.	Kickplates: Rigid polyvinyl chloride (PVC):
			1.	Fire Performance Characteristics: Provide UL Classified Cladding Material for fire door and fire door frames intended for application on listed door frames used with hollow metal and steel covered composite type fire doors rated up to 3 hours in accordance with UL 10B. Provide cUL (Canada accepted) Cladding Material intended for application on listed fire door frames used on hollow metal and steel composite type fire doors rated up to 3 hours in accordance with CAN4-S104-M80.
			2.	Fire Performance Characteristics: Provide UL Classified Cladding Material for doors and door frames intended for application on classified door frames used with wood composite and wood core type fire doors rated up to 1-1/2 hours in accordance with UL 10B. Provide cUL (Canada accepted) Cladding Material intended for application on classified wood composite and wood core type fire doors rated up to 1-1/2 hours in accordance with CAN4-S104-M80.
			3.	Self-Extinguishing: Provide kickplates with a CC1 classification, as tested in accordance with the procedures specified in ASTM D-635-74, Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Self-Supporting Plastics in a Horizontal Position, as referenced in UBC 52-4-1988.
			4.	Provide sheet materials that have been tested and results filed in compliance with article 15, part 1120 of the New York State uniform fire prevention and building code. DOS # 09960-930504-4001.
			5.	Impact Strength: Provide rigid vinyl sheet materials that have an Impact Strength of 30.4 ft-lbs/inch of thickness as tested in accordance with the procedures specified in ASTM D-256-90b, Impact Resistance of Plastics.
			6.	Chemical and Stain Resistance: Provide kickplates that show resistance to stain when tested in accordance with applicable provisions of ASTM D-543.
			7.	Fungal and Bacterial Resistance: Provide rigid vinyl that does not support fungal or bacterial growth as tested in accordance with ASTM G-21 and ASTM G-22.
			8.	Color Consistency: Provide components matched in accordance with SAE J-1545 - (Delta E) with a color difference no greater than 1.0 units using CIE Lab, CIE CMC, CIE LCh, Hunter Lab or similar color space scale systems.
	** NOTE TO SPECIFIER ** Select style. Delete one of the next two paragraphs.
			9.	Style: Rectangular kickplate.
			10.	Style: Designer kickplate.
	** NOTE TO SPECIFIER ** Select thickness. Delete two of the next three paragraphs.
			11.	Thickness: .040 inches (1mm).
			12.	Thickness: .060 inches (1.5mm).
			13.	Thickness: .080 inches (2mm).
	** NOTE TO SPECIFIER ** Insert dimensions in the next two paragraphs.
			14.	Width: _________.
			15.	Height: _________.
	** NOTE TO SPECIFIER ** Select backing type. Delete one of the next two paragraphs.
			16.	Backing: Adhesive Backed.
			17.	Backing: Unbacked.
	** NOTE TO SPECIFIER ** Select color requirement. Delete one of the next two paragraphs.
			18.	Color: To be selected by architect from manufacturer's standard colors.
			19.	Color: ________.
		B.	Kickplate: Stainless Steel.
	** NOTE TO SPECIFIER ** Select material. Type 430, 16 gauge is standard. Delete four of the next five paragraphs.
			1.	Material: Type 430, 16 gauge.
			2.	Material: Type 430, 14 gauge.
			3.	Material: Type 430, 18 gauge.
			4.	Material: Type 304 (meets NSF Standard 51), 14 gauge.
			5.	Material: Type 304 (meets NSF Standard 51), 16 gauge.
	** NOTE TO SPECIFIER ** Insert dimensions in the next two paragraphs.
			6.	Width_____________.
			7.	Height____________.
		C.	Kickplate: Gold Titanium Stainless Steel.
			1.	Material: Type 304 (meets NSF Standard 51), 18 gauge (standard)
	** NOTE TO SPECIFIER ** Insert dimensions in the next two paragraphs.
			2.	Width_____________.
			3.	Height____________.
		D.	Door Edge Protector: Rigid polyvinyl chloride (PVC).
	** NOTE TO SPECIFIER ** Select shape. Delete one of the next two paragraphs.
			1.	Shape: L-shaped 2 inch x 1-5/8 inch (51x41mm).
				a.	Attachment: With factory applied adhesive
				b.	Attachment: Without adhesive
			2.	Shape: U-shaped 1 inch x 1-3/4 inch x 1 inch (25x44x25mm)
	** NOTE TO SPECIFIER ** Select attachment method. Delete one of the next two paragraphs.
				a.	Attachment: Cement-on.
				b.	Attachment: Screw-on.
	** NOTE TO SPECIFIER ** Select angle. Delete one of the next two paragraphs.
			3.	Angle: 90 degrees.
			4.	Angle: 93 degrees.
	** NOTE TO SPECIFIER ** Select height requirement. Delete two of the next three paragraphs.
			5.	Height: 36 inches (.91m).
			6.	Height: 96 inches (2.44m).
			7.	Height: Custom - ______ inches.
		E.	Door Edge Protector: Stainless Steel.
	** NOTE TO SPECIFIER ** Select material. Type 430, 16 gauge is standard. Delete four of the next five paragraphs.
			1.	Material: Type 430, 16 gauge.
			2.	Material: Type 430, 14 gauge.
			3.	Material: Type 430, 18 gauge.
			4.	Material: Type 304 (meets NSF Standard 51), 14 gauge.
			5.	Material: Type 304 (meets NSF Standard 51), 16 gauge.
	** NOTE TO SPECIFIER ** Select shape. Delete one of the next two paragraphs.
			6.	Shape: L-shaped 1 inch x 1-3/4 inches (19x45mm).
			7.	Shape: U-shaped 3/4 inch x 1-3/4 inch x 3/4 inch (19x45x19mm).
	** NOTE TO SPECIFIER ** Select attachment method. Delete one of the next two paragraphs.
			8.	Attachment: Cement-on.
			9.	Attachment: Screw-on.
	** NOTE TO SPECIFIER ** Select angle. Delete one of the next two paragraphs.
			10.	Angle: 90 degrees.
			11.	Angle: 93 degrees.
	** NOTE TO SPECIFIER ** Select height requirement. Delete one of the next two paragraphs.
			12.	Height: 38 inches (65mm).
			13.	Height: Custom - ______ inches.
		F.	Door Frame Protection: Custom formed rigid polyvinyl chloride (PVC).
	** NOTE TO SPECIFIER ** Select thickness. .040 inch is standard Delete one of the next two paragraphs.
			1.	Thickness: .040 inch (1mm).
			2.	Thickness: .060 inch (1.5mm).
			3.	Profile: single piece to mate with doorframe.
	** NOTE TO SPECIFIER ** Select Dimensions. Delete five of the next six paragraphs.
			4.	Door Frame height and width: 36 inches (914mm) x up to 12 inches (305mm).
			5.	Door Frame height and width: 36 inches (914mm) x over 12 inches (305mm).
			6.	Door Frame height and width: 48 inches (1219mm) x up to 12 inches (305mm).
			7.	Door Frame height and width: 48 inches (1219mm) x over 12 inches (305mm).
			8.	Door Frame height and width: 96 inches (2438mm) x up to 12 inches (305mm).
			9.	Door Frame height and width: 96 inches (2438mm) x over 12 inches (305mm).
		G.	Door Frame Protection: High impact door frame guard.
			1.	3 inch (76mm) wide, .080 inch (2mm) thick bull-nosed 7/8 inch (21mm) radius, rigid vinyl cover over continuous .070 inch (1.8mm) aluminum retainer.
			2.	Provide top and bottom cap and dust cap of injection molded thermoplastics in color matching the vinyl cover.
	** NOTE TO SPECIFIER ** Select height. Delete two of the next three paragraphs.
			3.	Height: 36 inches (914mm).
			4.	Height: 48 inches (1219mm).
			5.	Height: 96 inches (2438mm).
		H.	Door Knob Protectors: Vacuum formed polyvinyl chloride (PVC).
			1.	Door Knob Protector: 9 inches h x 13-11/16 inches w x 2-3/4 inches deep (228x348x71mm).
			2.	Door Handle Protector: 16 inches h x 16 inches w x 3-7/8 inches deep (406x406x97mm).
			3.	Universal door knob protector: right side, 9-1/2 inches h x 15-1/2 inches w x 4-5/16 inches deep (241x394x110mm).
			4.	Universal door knob protector: left side, 9-1/2 inches h x 15-1/2 inches w x 4-5/16 inches deep (241x394x110mm).
	2.10	HEIGHTS
	** NOTE TO SPECIFIER ** If only one type and height is required for project, delete this article and add height to product description. If this article is retained, edit to reflect project requirements.
		A.	Heights: Provide corner guards in heights as follows:
			1.	Standard 4 Feet (1.22 m): Locate at ___________________.
			2.	Standard 8 Feet (2.44 m): Locate at ___________________.
			3.	Standard 9 Feet (2.74 m): Locate at ___________________.
			4.	Standard 12 Feet (3. 66 m): Locate at __________________.
			5.	As indicated on the drawings.
			6.	Height: ________________.
	2.11	ACCESSORIES
		A.	Provide appropriate fasteners and accessories as required to properly complete installation.
	PART 3	EXECUTION
	3.1	EXAMINATION
		A.	Verify that walls are in proper condition to receive installation of products.
	3.2	PREPARATION
		A.	Clean substrate to remove dust, debris, and loose particles.
	3.3	INSTALLATION
		A.	General: Install products level and plumb, in full compliance with manufacturer's installation instructions.
	3.4	ADJUSTING AND CLEANING
		A.	Verify that products are plumb and rigidly secured to substrate; make any adjustments required.
		B.	Clean products and immediate areas of installation, using materials and methods recommended by manufacturer. Remove from project site packaging and debris caused by installation.
	END OF SECTION