MasterFormat: 95

SpecWizard: customize this spec    Download this Bullet Resistant Products Specification for   WORD | WP | RTF | TEXT

Find over 500 more construction specifications | Arcat.com

	SECTION 13065
	BULLET RESISTANT PRODUCTS
	Copyright 2008 - 2011 ARCAT, Inc. - All rights reserved
	** NOTE TO SPECIFIER ** Armortex® Inc.; Bullet Resistant and physical security products. . This section is based on the products of Armortex® Inc., which is located at: 5926 Corridor Pkwy. Schertz, TX 78154 Toll Free Tel: 800-880-8306 Tel: 210-661-8306 Email: request info Web: www.armortex.com [ Click Here ] for additional information. Armortex® has been manufacturing Bullet Resistant and physical security products since 1980. Our product line includes Armortex® brand lightweight bullet and Blast Protection Composite panels, Bullet Resistant and containment glazing, Bullet Resistant transaction windows, pass-thru transaction equipment (drawers, hoppers, dip trays), speakers, gunports, guard towers, gun lockers, man traps, Bullet and Blast Resistant doors and related security equipment and aluminum storefront systems. Armortex® products are widely used in courtrooms, government and corporate offices, banks, convenience stores, gas stations, remote electronic buildings, check cashing facilities, cashier booths, prisons, vehicles and any place where ballistic and attack resistant security is required. Our Bullet and Blast Resistant products are available worldwide, direct from Armortex®. Phone, write or fax Armortex® for complete information.
	PART 1	GENERAL
	1.1	SECTION INCLUDES
	** NOTE TO SPECIFIER ** Delete items below not required for project.
		A.	Bullet Resistant Transaction Windows.
		B.	Bullet Resistant Hollow Metal Windows.
		C.	Bullet Resistant Aluminum Windows.
		D.	Bullet Resistant Metal Doors.
		E.	Bullet Resistant Wood Doors.
		F.	Bullet Resistant Transaction Equipment.
		G.	Bullet Resistant Speakers and Gun Ports.
		H.	Bullet Resistant and Detention Glazing.
		I.	Bullet Resistant Composite Panels.
	1.2	RELATED SECTIONS
	** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
		A.	Section 04899 - Masonry Assemblies: Masonry walls.
		B.	Section 05100 - Structural Metal Framing; Panel Supporting Members
		C.	Section 05500 - Metal Fabrications; Panel Supporting Members.
		D.	Section 06100 - Rough Carpentry; Panel Supporting Members.
		E.	Section 08710 - Door Hardware.
		F.	Section 08800 - Glazing.
		G.	Section 09300 - Plaster and Gypsum Board.
		H.	Section 09900 - Paints and Coatings.
	1.3	REFERENCES
	** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
		A.	ASTM C 1172 - Standard Specification for Laminated Architectural Flat Glass.
		B.	ASTM C 920 - Standard Specification for Elastomeric Joint Sealants.
		C.	ASTM C 1172 - Standard Specification for Laminated Architectural Flat Glass.
		D.	ASTM D 2000 - Standard Classification System for Rubber Products in Automotive Applications.
		E.	ASTM E 84 - Test method for the Surface Burning Characteristics of Building Materials.
		F.	AWS D1.1 - Structural Welding Code-Steel.
		G.	NIJ Standard 0108.01 - (National Institute of Justice) Standard for Ballistic Resistant Protective Materials (September, 1985).
		H.	UL 752 - Standard for Bullet Resisting Equipment (January 27, 1995)
	1.4	SUBMITTALS
		A.	Submit under provisions of Section 01300.
		B.	Product Data: Manufacturer's data sheets on each product to be used, including:
			1.	Preparation instructions and recommendations.
			2.	Storage and handling requirements and recommendations.
			3.	Installation methods.
		C.	Shop Drawings:
			1.	Submit shop drawings prepared by the manufacturer showing plans, sections, elevations, layouts, profiles and product component locations, including anchorage, bracing, fasteners, accessories and finishes.
			2.	Include dimensioned elevation of each type opening assembly in project; indicate sizes and locations of hardware, and lites if specified.
			3.	Schedule: Indicate each opening assembly in project; cross-referenced to plans, elevations, and details.
		D.	Design data: Bullet resistance analysis design calculations for specific project conditions, certifying system conformance to specified performance requirements.
		E.	Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.
		F.	Test Reports: Certified test reports showing compliance with specified performance characteristics and physical properties.
		G.	Closeout submittals: Warranty documents, issued and executed by manufacturer of systems, countersigned by Contractor.
	1.5	QUALITY ASSURANCE
		A.	Manufacturer Qualifications: Company specializing in manufacturing products of the type specified with a minimum documented experience of five years.
		B.	Installer Qualifications: Company specializing in installation of products specified with minimum three years documented experience.
	** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.
		C.	Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.
			1.	Finish areas designated by Architect.
			2.	Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.
			3.	Refinish mock-up area as required to produce acceptable work.
			4.	Accepted mock-ups shall be comparison standard for remaining Work
		D.	Pre-installation Meetings: Conduct pre-installation meeting to verify project requirements, substrate conditions, and manufacturer's installation instructions.
		E.	Coordination of Work: Coordinate layout and installation of components with other construction supported by, or penetrating through, ceilings, including light fixtures, HVAC equipment, fire-suppression system, and partitions.
	1.6	DELIVERY, STORAGE, AND HANDLING
		A.	Deliver materials in manufacturer's unopened, undamaged packaging, with manufacturer's labels intact.
		B.	Remove wraps or covers from doors and frames upon delivery at the building site; clean and touch-up scratches or disfigurement caused by shipping or handling promptly.
		C.	Store products in manufacturer's unopened packaging until ready for installation.
		D.	Store assemblies, off the ground and on end, to prevent damage to face corners and edges.
		E.	Store assemblies covered to protect them from damage but permitting air circulation.
	1.7	SEQUENCING
		A.	Ensure that locating templates and other information required for installation of products of this section are furnished to affected trades in time to prevent interruption of construction progress.
		B.	Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.
	1.8	PROJECT CONDITIONS
		A.	Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.
	PART 2	PRODUCTS
	2.1	MANUFACTURERS
		A.	Acceptable Manufacturer: Armortex® Inc., which is located at: 5926 Corridor Pkwy. ; Schertz, TX 78154; Toll Free Tel: 800-880-8306; Tel: 210-661-8306; Email: request info; Web: www.armortex.com
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
		B.	Substitutions: Not permitted.
		C.	Requests for substitutions will be considered in accordance with provisions of Section 01600.
	2.2	APPLICATIONS/SCOPE
		A.	Bullet resistant protection shall be provided in the sizes and in the configuration indicated on the Drawings.
		B.	Furnish all hardware necessary for the joining of the components specified.
		C.	Provide components complete with adhesive, fasteners, and other devices required for complete assembly.
	** NOTE TO SPECIFIER ** Select the bullet resistant transaction windows required from the following paragraphs and delete those not required.
	2.3	BULLET RESISTANT TRANSACTION WINDOWS
		A.	Baffle Design Transaction Barrier Window with Natural Voice Communication: Armortex Model SSTW-60, Baffle Window Assembly with two way "natural voice" communication permitted by the design of the vision panels and the offset vertical side baffles and acrylic spacers. All components are cut to size with necessary holes pre-drilled and tapped where required. Edges of all glazing are polished. Aluminum anchor supports and stainless steel fasteners are provided as required for complete assembly.
	** NOTE TO SPECIFIER ** Select one of the following two paragraphs and delete the one not required. Insert size as required.
			1.	Width:
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Indicate unit configurations and sizes on the Drawings.
				a.	Overall Size and Configuration: As indicated on the Drawings.
			2.	Height:
				a.	Size: As indicated on the Drawings.
			3.	Head and Sill Anchor Supports:
				a.	Extruded anodized aluminum angles.
				b.	Extruded anodized aluminum channels.
			4.	Side Jamb Anchor Supports: Extruded anodized aluminum angles, 1-1/4 inch by 1-1/4 inch by 1/8 inch.
			5.	Baffles: Laminated polycarbonate, bullet resistant UL level 3, nominal 1-1/4 inch thick. Baffles 5 inches deep by full height of the opening.
			6.	Glazing Type: Laminated Polycarbonate. Glazing to conform to UL 752 with a Level 3 protection level.
			7.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
		B.	C Channel Transaction Window with Voice Communication: Armortex Model SSTW preassembled with two way "natural voice" communication permitted by the design of the vertical side frames and neoprene spacer glazing technique.
	** NOTE TO SPECIFIER ** Windows are available in single SSTW or multiple SSTW-09 configurations. Indicate unit configurations and sizes on the Drawings.
			1.	Overall Size and Configuration: As indicated on the Drawings.
			2.	Frame: Stainless steel, 12 gauge with a No. 3 finish. Frame conforms to UL 752 Rating Level 3. Vertical jambs are fabricated with a minimum of 3 predrilled holes on each jamb to permit anchoring to structural backing. Hole located to prohibit access from the opposite site of the frame.
			3.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
	** NOTE TO SPECIFIER ** Select protection level required from the following two paragraphs and delete those not required.
					1)	Level 1.
					2)	Level 2.
					3)	Level 3.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
	** NOTE TO SPECIFIER ** Shelf is optional delete if not required.
			4.	Shelf: Full width of window and a minimum of 12 inches deep centered under the glazing:
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required.
				a.	Solid core covered with a black high pressure laminate.
				b.	Stainless steel 18 gauge minimum with a No. 3 finish.
				c.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
		C.	C Channel Split Frame Transaction Window with Voice Communication: Armortex Model SSTW-05 preassembled with two way "natural voice" communication permitted by the design of the vertical side frames and neoprene spacer glazing technique.
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Indicate unit configurations and sizes on the Drawings.
			1.	Overall Size and Configuration: As indicated on the Drawings.
	** NOTE TO SPECIFIER ** Select frame type required from the following two paragraphs and delete the one not required.
			2.	Frame: Carbon steel, 16 gauge adjustable wrap frame with a prime painted finish. Exterior faced with bullet resistant composite. Frame conforms to UL 752 Rating Level 3.
			3.	Frame: Stainless steel, 16 gauge adjustable wrap frame with a No. 3 finish. Exterior faced with bullet resistant composite. Frame conforms to UL 752 Rating Level 3.
			4.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
	** NOTE TO SPECIFIER ** Select protection level required from the following two paragraphs and delete those not required.
					1)	Level 1.
					2)	Level 2.
					3)	Level 3.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
	** NOTE TO SPECIFIER ** Shelf is optional delete if not required.
			5.	Shelf: Full width of window and a minimum of 12 inches deep centered under the glazing:
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required.
				a.	Solid core covered with a black high pressure laminate.
				b.	Stainless steel 18 gauge minimum with a No. 3 finish.
				c.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
		D.	C Channel Transaction Window with Transparent Package Receiver and Voice Communication: Armortex Model SSTW-07 preassembled with transparent package receiver and two way "natural voice" communication permitted by the design of the vertical side frames and neoprene spacer glazing technique.
	** NOTE TO SPECIFIER ** Windows are available in single configurations. Indicate unit configuration and sizes on the Drawings.
			1.	Overall Size and Configuration: As indicated on the Drawings.
			2.	Frame: Stainless steel, 12 gauge with a No. 3 finish. Frame conforms to UL 752 Rating Level 3. Vertical jambs are fabricated with a minimum of 3 predrilled hole on each jamb to permit anchoring to structural backing. Hole located to prohibit access from the opposite site of the frame.
			3.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
	** NOTE TO SPECIFIER ** Select protection level required from the following two paragraphs and delete those not required.
					1)	Level 1.
					2)	Level 2.
					3)	Level 3.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
			4.	Shelf: Full width of window and a minimum of 12 inches deep centered under the glazing:
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required.
				a.	Solid core covered with a black high pressure laminate.
				b.	Stainless steel 18 gauge minimum with a No. 3 finish.
				c.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
			5.	Package Receiver: Polycarbonate with polished edges, 18 inches deep, 18 inches wide and 18 inches high with access door on both the front and rear.
		E.	C Channel Transaction Window with Hinged Panel and Voice Communication: Armortex Model SSTW-10 preassembled with two way "natural voice" communication permitted by the design of the vertical side frames and neoprene spacer glazing technique.
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Indicate unit configurations and sizes on the Drawings.
			1.	Overall Size and Configuration: As indicated on the Drawings.
			2.	Frame: Stainless steel, 12 gauge with a No. 3 finish. Frame conforms to UL 752 Rating Level 3. Vertical jambs are fabricated with a minimum of 3 predrilled hole on each jamb to permit anchoring to structural backing. Hole located to prohibit access from the opposite site of the frame.
			3.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 Level 3.
				b.	Glazing Type: Polycarbonate
			4.	Hinged Panel: Polycarbonate to match glazing with stainless steel hinge, pull knob and security latch.
	** NOTE TO SPECIFIER ** Shelf is optional delete if not required.
			5.	Shelf: Full width of window and a minimum of 12 inches deep centered under the glazing:
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required.
				a.	Solid core covered with a black high pressure laminate.
				b.	Stainless steel 18 gauge minimum with a No. 3 finish.
				c.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
		F.	Three Sided HM Transaction Window with Speaker: Armortex Model SSTW-16 preassembled with speaker and non-ricochet type frame design.
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Indicate unit configurations and sizes on the Drawings.
			1.	Overall Size and Configuration: As indicated on the Drawings.
	** NOTE TO SPECIFIER ** Select frame type required from the following two paragraphs and delete the one not required.
			2.	Frame: Carbon steel, 16 gauge adjustable wrap frame with a prime painted finish. Interior of exterior face lined with bullet resistant composite. Frame conforms to UL 752 Rating Level 3. Provide with matching 1 inch by 1 inch removable glazing stop.
			3.	Frame: Stainless steel, 16 gauge adjustable wrap frame with a No. 3 finish. Interior of exterior face lined with bullet resistant composite. Frame conforms to UL 752 Rating Level 3. Provide with matching 1 inch by 1 inch removable glazing stop.
			4.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
	** NOTE TO SPECIFIER ** Select protection level required from the following two paragraphs and delete those not required.
					1)	Level 1.
					2)	Level 2.
					3)	Level 3.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
	** NOTE TO SPECIFIER ** Hinged panel is optional delete if not required.
			5.	Hinged Panel: Polycarbonate to match glazing with stainless steel hinge, pull knob and security latch.
	** NOTE TO SPECIFIER ** Shelf is optional delete if not required.
			6.	Shelf: Full width of window and a minimum of 12 inches deep centered under the glazing:
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required.
				a.	Solid core covered with a black high pressure laminate.
				b.	Stainless steel 18 gauge minimum with a No. 3 finish.
				c.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
			7.	Speaker: Speaker Model SSBRS-7.
	** NOTE TO SPECIFIER ** Sidelight(s) are optional delete if not required.
			8.	Bullet Resistant Sidelights: Provide fixed sidelights with frames, glazing and protection level matching the transaction window specified.
		G.	Three Sided HM Transaction Window with Voice Communication: Armortex Model SSTW-19 preassembled with non-ricochet type frame design and two way "natural voice" communication permitted by the design of the vertical side frames and neoprene spacer glazing technique.
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Indicate configurations and sizes on the Drawings.
			1.	Overall Size and Configuration: As indicated on the Drawings.
	** NOTE TO SPECIFIER ** Select frame type required from the following two paragraphs and delete the one not required.
			2.	Frame: Carbon steel, 16 gauge adjustable wrap frame with a prime painted finish. Interior of exterior face lined with bullet resistant composite. Frame conforms to UL 752 Rating Level 3. Provide with matching 1 inch by 1 inch removable glazing stop.
			3.	Frame: Stainless steel, 16 gauge adjustable wrap frame with a No. 3 finish. Interior of exterior face lined with bullet resistant composite. Frame conforms to UL 752 Rating Level 3. Provide with matching 1 inch by 1 inch removable glazing stop.
			4.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
	** NOTE TO SPECIFIER ** Select protection level required from the following two paragraphs and delete those not required.
					1)	Level 1.
					2)	Level 2.
					3)	Level 3.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
	** NOTE TO SPECIFIER ** Hinged panel is optional delete if not required.
			5.	Hinged Panel: Polycarbonate to match glazing with stainless steel hinge, pull knob and security latch.
	** NOTE TO SPECIFIER ** Shelf is optional delete if not required.
			6.	Shelf: Full width of window and a minimum of 12 inches deep centered under the glazing:
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required.
				a.	Solid core covered with a black high pressure laminate.
				b.	Stainless steel 18 gauge minimum with a No. 3 finish.
				c.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
	** NOTE TO SPECIFIER ** Sidelight(s) are optional delete if not required.
			7.	Bullet Resistant Sidelights: Provide fixed sidelights with frames, glazing and protection level matching the transaction window specified but without communication feature.
		H.	Split Frame Three Sided HM Transaction Window with Voice Communication: Armortex Model SSTW-21 preassembled with non-ricochet type frame design and two way "natural voice" communication permitted by the design of the vertical side frames and neoprene spacer glazing technique.
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Indicate configurations and sizes on the Drawings.
			1.	Overall Size and Configuration: As indicated on the Drawings.
	** NOTE TO SPECIFIER ** Select frame type required from the following two paragraphs and delete the one not required.
			2.	Adjustable Split Frame: Carbon steel, 16 gauge adjustable wrap frame with a prime painted finish. Interior of exterior face lined with bullet resistant composite. Frame conforms to UL 752 Rating Level 3. Provide with matching 1 inch by 1 inch removable glazing stop.
			3.	Adjustable Split Frame: Stainless steel, 16 gauge adjustable wrap frame with a No. 3 finish. Interior of exterior face lined with bullet resistant composite. Frame conforms to UL 752 Rating Level 3. Provide with matching 1 inch by 1 inch removable glazing stop.
			4.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
	** NOTE TO SPECIFIER ** Select protection level required from the following two paragraphs and delete those not required.
					1)	Level 1.
					2)	Level 2.
					3)	Level 3.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
	** NOTE TO SPECIFIER ** Hinged panel is optional delete if not required.
			5.	Hinged Panel: Polycarbonate to match glazing with stainless steel hinge, pull knob and security latch.
	** NOTE TO SPECIFIER ** Shelf is optional delete if not required.
			6.	Shelf: Full width of window and a minimum of 12 inches deep centered under the glazing:
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required.
				a.	Solid core covered with a black high pressure laminate.
				b.	Stainless steel 18 gauge minimum with a No. 3 finish.
				c.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
	** NOTE TO SPECIFIER ** Sidelight(s) are optional delete if not required.
			7.	Bullet Resistant Sidelights: Provide fixed sidelights with frames, glazing and protection level matching the transaction window specified but without communication feature.
		I.	Three Sided HM Transaction Sliding Window: Armortex Model preassembled with speaker and non-ricochet type frame design.
	** NOTE TO SPECIFIER ** Windows are available in custom sizes. Select one of the following paragraphs and delete the one not required. Complete sizes below or show sizes on the Drawings. Consult with manufacturer with size limitations.
			1.	Model SSTW-23 Single Slide Window Size: __ inches wide by __ inches high.
			2.	Model SSTW-25 Double Slide Window Size: __ inches wide by __ inches high.
			3.	Overall Size and Configuration: As indicated on the Drawings.
	** NOTE TO SPECIFIER ** Select frame type required from the following two paragraphs and delete the one not required.
			4.	Frame: Carbon steel, 16 gauge adjustable wrap frame with a prime painted finish. Interior of exterior face lined with bullet resistant composite. Frame conforms to UL 752 Rating Level 3. Provide with matching 1 inch by 1 inch removable glazing stop.
			5.	Frame: Stainless steel, 16 gauge adjustable wrap frame with a No. 3 finish. Interior of exterior face lined with bullet resistant composite. Frame conforms to UL 752 Rating Level 3. Provide with matching 1 inch by 1 inch removable glazing stop.
			6.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge stainless steel with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
	** NOTE TO SPECIFIER ** Select protection level required from the following paragraphs and delete those not required.
					1)	Level 1.
					2)	Level 3.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Polycarbonate.
					2)	Acrylic.
			7.	Hardware:
				a.	Roller Track 1500 Series.
				b.	12 gauge stainless steel roller guard.
				c.	Bottom track 12 gauge stainless steel.
				d.	Handpull.
	** NOTE TO SPECIFIER ** Shelf is optional delete if not required.
			8.	Shelf: Full width of window and a minimum of 12 inches deep centered under the glazing:
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required.
				a.	Solid core covered with a black high pressure laminate.
				b.	Stainless steel 18 gauge minimum with a No. 3 finish.
				c.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
	** NOTE TO SPECIFIER ** Sidelight(s) are optional delete if not required.
			9.	Bullet Resistant Sidelights: Provide fixed sidelights with frames, glazing and protection level matching the transaction window specified.
		J.	Clamp-On Frame Aluminum Transaction Window: Armortex Model preassembled with non-ricochet type frame design. Frame conforms to UL 752 Rating Level 3.
	** NOTE TO SPECIFIER ** Select frame type required from the following three paragraphs and delete the ones not required.
			1.	Provide frame design with two way "natural voice" communication permitted by the design of the vertical side frames and neoprene spacer glazing technique.
			2.	Provide fixed frame design with Speaker Model SSBRS-7 in glazing.
			3.	Provide fixed frame design.
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Windows are available in custom sizes. Select one of the following paragraphs and delete the one not required. Complete sizes below or show sizes on the Drawings. Consult with manufacturer with size limitations.
			4.	Window Size: __ inches wide by __ inches high.
			5.	Overall Size and Configuration: As indicated on the Drawings.
			6.	Frame: Adjustable Two Piece Clamp-On Frame. Anodized 6063-T6 extruded aluminum with internal bullet resistant composite. Provide with matching secure side removable glazing stop.
			7.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
	** NOTE TO SPECIFIER ** Select protection level required from the following two paragraphs and delete the one not required.
					1)	Level 1.
					2)	Level 3.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
	** NOTE TO SPECIFIER ** Hinged panel is optional delete if not required.
			8.	Hinged Panel: Polycarbonate to match glazing with stainless steel hinge, pull knob and security latch.
	** NOTE TO SPECIFIER ** Shelf is optional delete if not required.
			9.	Shelf:
	** NOTE TO SPECIFIER ** Select shelf type required from the following paragraphs and delete those not required.
				a.	Full width of window and a minimum of 12 inches deep centered under the glazing.
				b.	Full width of window centered under the glazing and of depth indicated on the Drawings.
				c.	Provided as specified in Section ______.
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required. Delete entirely if shelf is specified elsewhere
				d.	Solid core covered with a black high pressure laminate.
				e.	Stainless steel 18 gauge minimum with a No. 3 finish.
				f.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
	** NOTE TO SPECIFIER ** Sidelight(s) are optional delete if not required.
			10.	Bullet Resistant Sidelights: Provide fixed sidelights with frames, glazing and protection level matching the transaction window specified but without communication feature.
		K.	Fixed Depth Frame Aluminum Transaction Window: Armortex Model preassembled with non-ricochet type frame design. Frame conforms to UL 752 Rating Level 3.
	** NOTE TO SPECIFIER ** Select frame type required from the following three paragraphs and delete the ones not required.
			1.	Provide frame design with two way "natural voice" communication permitted by the design of the vertical side frames and neoprene spacer glazing technique.
			2.	Provide fixed frame design with Speaker Model SSBRS-7 in glazing.
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Windows are available in custom sizes. Select one of the following paragraphs and delete the one not required. Complete sizes below or show sizes on the Drawings. Consult with manufacturer with size limitations.
			3.	Window Size: __ inches wide by __ inches high.
			4.	Overall Size and Configuration: As indicated on the Drawings.
			5.	Frame: Anodized 6063-T6 extruded aluminum with internal bullet resistant composite. Provide with matching secure side removable glazing stop.
			6.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
	** NOTE TO SPECIFIER ** Select protection level required from the following two paragraphs and delete the one not required.
					1)	Level 1.
					2)	Level 3.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
	** NOTE TO SPECIFIER ** Hinged panel is optional delete if not required.
			7.	Hinged Panel: Polycarbonate to match glazing with stainless steel hinge, pull knob and security latch.
	** NOTE TO SPECIFIER ** Shelf is optional delete if not required.
			8.	Shelf:
	** NOTE TO SPECIFIER ** Select shelf type required from the following paragraphs and delete those not required.
				a.	Full width of window and a minimum of 12 inches deep centered under the glazing.
				b.	Full width of window centered under the glazing and of depth indicated on the Drawings.
				c.	Provided as specified in Section ______.
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required. Delete entirely if shelf is specified elsewhere
				d.	Solid core covered with a black high pressure laminate.
				e.	Stainless steel 18 gauge minimum with a No. 3 finish.
				f.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
	** NOTE TO SPECIFIER ** Sidelight(s) are optional delete if not required.
			9.	Bullet Resistant Sidelights: Provide fixed sidelights with frames, glazing and protection level matching the transaction window specified but without communication feature.
		L.	Fixed Depth Frame Aluminum Transaction Sliding Window: Armortex Model preassembled with non-ricochet type frame design. Frame conforms to UL 752 Rating Level 3.
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Windows are available in custom sizes. Select one of the following paragraphs and delete the one not required. Complete sizes below or show sizes on the Drawings. Consult with manufacturer with size limitations.
			1.	Window Size: __ inches wide by __ inches high.
			2.	Overall Size and Configuration: As indicated on the Drawings.
			3.	Frame: Anodized 6063-T6 extruded aluminum with internal bullet resistant composite. Provide with matching secure side removable glazing stop.
			4.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
	** NOTE TO SPECIFIER ** Select protection level required from the following two paragraphs and delete the one not required.
					1)	Level 1.
					2)	Level 3.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
			5.	Hardware:
				a.	Roller Track 1500 Series.
				b.	12 gauge stainless steel roller guard.
				c.	Bottom track 12 gauge stainless steel.
				d.	Handpull.
	** NOTE TO SPECIFIER ** Shelf is optional delete if not required.
			6.	Shelf: Full width of window and a minimum of 12 inches deep centered under the glazing:
	** NOTE TO SPECIFIER ** Select shelf type required from the following two paragraphs and delete the one not required.
				a.	Solid core covered with a black high pressure laminate.
				b.	Stainless steel 18 gauge minimum with a No. 3 finish.
				c.	Dip Tray: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under the glazing no less than 1-5/8 inch. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
	** NOTE TO SPECIFIER ** Sidelight(s) are optional delete if not required.
			7.	Bullet Resistant Sidelights: Provide fixed sidelights with frames, glazing and protection level matching the transaction window specified.
	** NOTE TO SPECIFIER ** Select the bullet resistant aluminum windows required from the following paragraphs and delete if not required.
	2.4	BULLET RESISTANT ALUMINUM WINDOWS
		A.	Fixed, Thermally Broken, Bullet Resistant, Aluminum Windows: Amortex 625 BR Thermally Broken Aluminum Bullet Resistant Window, Up to 30 Caliber Armor Piecing. Fabricated of extruded aluminum with a thermal break between the interior and exterior surfaces. All surfaces smooth with no exposed fasteners.
			1.	Performance:
				a.	Windows shall conform to UL 752 for the following level of protection:
	** NOTE TO SPECIFIER ** Select one of the following performance standards as required. Delete those not required.
					1)	Level 1 Protection.
					2)	Level 2 Protection.
					3)	Level 3 Protection.
					4)	Level 4 Protection.
					5)	Level 5 Protection.
					6)	Level 6 Protection.
					7)	Level 7 Protection.
					8)	Level 8 Protection.
				b.	Windows shall conform to NIJ 0108.01 Standard for the following level of protection:
	** NOTE TO SPECIFIER ** Select one of the following performance standards as required. Delete those not required.
					1)	Level I.
					2)	Level II.
					3)	Level IIIa.
					4)	Level III.
					5)	Level IV.
			2.	Frame:
				a.	Size: Face 2-1/2 inch and 6 inches deep.
				b.	Material: Extruded aluminum, alloy and temper 6005-T6. Ultimate tensile strength of 37.7 ksi, and shear strength of 29.7 ksi.
				c.	Thermal Break: Continuous structural urethane thermal barrier around the entire perimeter of the frame that shall not be bridged by any metal conductor at any point. Thermally "improved" frames are not acceptable.
				d.	Glazing Cavity: Minimum of 1.75 inch deep and 2.875 wide.
			3.	Glass: Field glazed with laminated glass conforming to ASTM C 1172 and conforming to the level of protection specified. Glazing shall be:
				a.	Clear, flat annealed transparent laminated glass.
				b.	Insulated clear, flat annealed transparent laminated glass.
				c.	Insulated clear, flat annealed low E laminated glass.
			4.	Glazing: Glaze windows in accordance with GANA guide lines.
				a.	Silicone: Structural silicone Dow Corning 995 complying with ASTM C 920.
				b.	Setting Blocks: Neoprene in strict compliance with ASTM C 509 Type II option and ASTM C 864 with a 80-85 shore "A" durometer as tested under ASTM D 2000.
			5.	Anchors: Provide as required to suit the protection level specified.
			6.	Finish: Clear anodized aluminum 204-R1 Class-II anodized aluminum coating.
	** NOTE TO SPECIFIER ** Select the bullet resistant metal windows required from the following paragraphs and delete those not required.
	2.5	BULLET RESISTANT HOLLOW METAL WINDOWS
		A.	Fixed HM Window: Armortex Model SSFW preassembled with speaker and non-ricochet type frame design.
	** NOTE TO SPECIFIER ** Select frame type required from the following three paragraphs and delete the ones not required.
			1.	Provide frame design with two way "natural voice" communication permitted by the design of the vertical side frames and neoprene spacer glazing technique.
			2.	Provide fixed frame design with Speaker Model SSBRS-7 in glazing.
			3.	Provide fixed frame design.
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Windows are available in custom sizes. Select one of the following paragraphs and delete the one not required. Complete sizes below or show sizes on the Drawings. Consult with manufacturer with size limitations.
			4.	Window Size: __ inches wide by __ inches high.
			5.	Overall Size and Configuration: As indicated on the Drawings.
	** NOTE TO SPECIFIER ** Select frame type required from the following four paragraphs and delete the ones not required.
			6.	Fixed Frame: Carbon steel, 16 gauge frame with a prime painted finish. Interior of exterior face lined with bullet resistant composite as required for protection level specified. Provide with matching 1 inch by 1 inch removable glazing stop.
				a.	Frame to conform to UL 752 of the following protection level.
					1)	Levels 1 - 8, plus .30 caliber and .50 caliber AP.
			7.	Fixed Frame: Stainless steel, 16 gauge frame with a No. 3 finish. Interior of exterior face lined with bullet resistant composite as required for protection level specified. Provide with matching 1 inch by 1 inch removable glazing stop.
				a.	Frame to conform to UL 752 of the following protection level.
					1)	Levels 1 - 8, plus .30 caliber and .50 caliber AP.
			8.	Adjustable Split Frame: Carbon steel, 16 gauge adjustable wrap frame with a prime painted finish. Interior of exterior face lined with bullet resistant composite as required for protection level specified. Provide with matching 1 inch by 1 inch removable glazing stop.
				a.	Frame to conform to UL 752 of the following protection level.
					1)	Levels 1 - 8, plus .30 caliber and .50 caliber AP.
			9.	Adjustable Split Frame: Stainless steel, 16 gauge adjustable wrap frame with a No. 3 finish. Interior of exterior face lined with bullet resistant composite as required for protection level specified. Provide with matching 1 inch by 1 inch removable glazing stop.
				a.	Frame to conform to UL 752 of the following protection level.
					1)	Levels 1 - 8.
			10.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
					1)	Levels 1 - 8 plus AP.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
		B.	Fixed Aluminum Windows: Armortex Model preassembled with non-ricochet type frame design.
	** NOTE TO SPECIFIER ** Select frame type required from the following three paragraphs and delete the ones not required.
			1.	Provide frame design with two way "natural voice" communication permitted by the design of the vertical side frames and neoprene spacer glazing technique.
			2.	Provide fixed frame design with Speaker Model SSBRS-7 in glazing.
			3.	Provide fixed frame design.
	** NOTE TO SPECIFIER ** Windows are available in single or multiple configurations. Windows are available in custom sizes. Select one of the following paragraphs and delete the one not required. Complete sizes below or show sizes on the Drawings. Consult with manufacturer with size limitations.
			4.	Window Size: __ inches wide by __ inches high.
			5.	Overall Size and Configuration: As indicated on the Drawings.
	** NOTE TO SPECIFIER ** Select frame type required from the following four paragraphs and delete the ones not required.
			6.	Fixed Frame: Adjustable Two Piece Clamp-On Frame. Anodized 6063-T6 extruded aluminum with internal bullet resistant composite as required for protection level specified. Provide with matching 1 inch by 1 inch removable glazing stop.
				a.	Frame to conform to UL 752 of the following protection level.
					1)	Levels 1 - 8, plus .30 caliber and .50 caliber AP.
			7.	Adjustable Split Frame: Anodized 6063-T6 extruded aluminum with internal bullet resistant composite as required for protection level specified. Provide with matching 1 inch by 1 inch removable glazing stop.
				a.	Frame to conform to UL 752 of the following protection level.
					1)	Levels 1 - 8, plus .30 caliber and .50 caliber AP.
			8.	Glazing: Top and bottom edge of the glazing to be capped with a minimum 20 gauge with a No. 3 finish.
				a.	Glazing to conform to UL 752 of the following protection level.
					1)	Levels 1 - 8, plus AP.
				b.	Glazing Type:
	** NOTE TO SPECIFIER ** Select glazing type required from the following paragraphs and delete those not required.
					1)	Laminated Glass/Airspace/Laminated Polycarbonate.
					2)	Polycarbonate Acrylic Composite.
					3)	Multi-Ply Laminated Glass.
					4)	Glass/ Polycarbonate Composite.
	** NOTE TO SPECIFIER ** Select the bullet resistant metal doors required from the following paragraphs and delete those not required.
	2.6	BULLET RESISTANT HOLLOW METAL DOORS
		A.	Bullet Resistant Hollow Metal Steel Doors and Frames: Provide door and frame prehung with factory primed finish. Doors and frames of a "non-ricochet type" design with a Armortex Bullet Resistant Fiberglass ballistic encapturing barrier complying with ASTM E 119 with a one hour fire rating.
			1.	Steel Doors:
	** NOTE TO SPECIFIER ** Steel doors a are available in single door, double door and door with sidelight configurations. Consult with manufacturer with size limitations.
				a.	Door, Sizes and Configurations: As indicated on the Drawings.
	** NOTE TO SPECIFIER ** Select the door types required from the following paragraphs as required. Delete those not required.
					1)	Flush Unglazed Door Type NL.
					2)	Flush Glazed Door Type VL with a 10 inch by 10 inch glazed opening.
					3)	Flush Glazed Door Type SL with a 4 inch by 22 inch glazed opening.
					4)	Flush Glazed Door Type HL with a 21 inch by 32 inch glazed opening.
					5)	Flush Glazed Door Type DL with a 21 inch by 32 inch and a 21 inch by 21 inch glazed opening.
					6)	Flush Glazed Door Type FL with a 21 inch by 58 inch glazed opening.
				b.	Thickness:
					1)	1-3/4 inches (44 mm) minimum.
				c.	Face sheets:
					1)	Doors for interior use: Steel sheet, 16 gauge, factory primed.
					2)	Doors for exterior use: Galvanized steel sheet, 16 gauge, factory primed.
					3)	Visible seams on face sheets not permitted.
				d.	Core:
					1)	Fill spaces between face sheets with foamed in place rigid urethane foam and fiberglass core
				e.	Vertical edges:
					1)	Join face sheets by continuous welding. Grind and fill, dress welds to smooth flush surface.
					2)	Visible seams on vertical edges not permitted.
				f.	Horizontal edges:
					1)	Close top and bottom edges of doors with inverted continuous recessed steel channels, 12 gage minimum; spot-weld channels to both door faces.
					2)	Provide additional flush closing channel at top and bottom edges of exterior doors; spot-weld channel to both door faces.
					3)	Provide openings in bottom closure of exterior doors to permit escape of entrapped moisture.
				g.	Hardware preparation:
					1)	Mortise, reinforce, drill, and tap doors at factory for fully templated mortised hardware only, in accordance with approved hardware schedule and supplied templates.
					2)	Provide reinforcing plates at surface-mounted or non-templated hardware locations.
				h.	Glazing Moldings and stops:
					1)	Weld fixed moldings to door on security side.
					2)	Loose stops, countersunk for fasteners.
					3)	Form moldings with mitered corner joints.
				i.	Glazed lites: Factory-assemble lites in doors indicated to have lites, using glazing materials of the same ballistic level specified for the door and frame.
	** NOTE TO SPECIFIER ** HM frames are suitable for UL 752 Levels 1 to 8. Contact manufacturer for requirements for openings with higher levels.
			2.	HM Door Frames: Welded units with integral trim, of sizes and profiles indicated and as follows:
	** NOTE TO SPECIFIER ** Steel frames are available in multiple configurations including Wrap Frame, Split Frame, Butt Frame (for existing masonry/concrete openings), and Butt Frame for masonry built-in.
				a.	Frame Sizes and Configuration: As indicated on the Drawings.
				b.	Frames for interior use: Steel sheet, minimum 16 gage thickness, factory primed.
				c.	Frames for exterior use: Galvanized steel sheet, minimum 16 gage thickness, factory primed.
				d.	Stops: Minimum 5/8 inch (15.8 mm) in depth.
				e.	Contact edges of joints and mitered perimeter trim faces, continuously welded.
				f.	Hardware preparation:
					1)	Mortise, reinforce, drill, and tap frames at factory for fully templated mortised hardware, in accordance with approved hardware schedule.
					2)	Provide reinforcing plates at surface-mounted hardware locations.
				g.	Floor anchors:
					1)	Minimum 18 gage steel.
					2)	Weld anchors inside each jamb for floor anchorage.
				h.	Jamb anchors:
					1)	Weld anchors inside each jamb for wall anchorage.
					2)	Anchors of types suitable for adjacent wall construction.
				i.	Plaster guards: Minimum 26 gage galvanized steel; welded in place at hardware mortises on frames to be set in masonry or concrete openings.
				j.	Provide with temporary steel spreader welded to jamb feet for bracing during shipping and handling.
			3.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
				g.	UL 752 Level 7.
				h.	UL 752 Level 8.
				i.	UL 752 Level 9.
				j.	UL 752 Level 10.
	** NOTE TO SPECIFIER ** Select the bullet resistant wood doors required from the following paragraphs and delete those not required.
	2.7	BULLET RESISTANT WOOD DOORS
		A.	Bullet Resistant Wood Doors and Steel Frames: Provide door and frame prehung. Doors and frames of a "non-ricochet type" design with a Armortex Bullet Resistant Fiberglass ballistic encapturing barrier complying with ASTM E 119 with a one hour fire rating.
	** NOTE TO SPECIFIER ** Steel doors a are available in single door, double door and door with sidelight configurations. Consult with manufacturer with size limitations.
			1.	Door, Sizes and Configurations: As indicated on the Drawings.
	** NOTE TO SPECIFIER ** Select the door types required from the following paragraphs as required. Delete those not required.
				a.	Flush Unglazed Door Type NL.
				b.	Flush Glazed Door Type VL with a 10 inch by 10 inch glazed opening.
				c.	Flush Glazed Door Type SL with a 4 inch by 22 inch glazed opening.
				d.	Flush Glazed Door Type HL with a 21 inch by 32 inch glazed opening.
				e.	Flush Glazed Door Type DL with a 21 inch by 32 inch and a 21 inch by 21 inch glazed opening.
				f.	Flush Glazed Door Type FL with a 21 inch by 58 inch glazed opening.
			2.	Solid Core Wood Doors:
				a.	Thickness:
					1)	1-3/4 inches (44 mm) minimum.
				b.	Face sheets:
	** NOTE TO SPECIFIER ** Select the door face type required from the following paragraphs as required. Delete the one not required.
					1)	Plain sliced red oak veneer.
					2)	Custom veneer as selected by the Architect.
				c.	Core:
					1)	Fill spaces between face sheets with foamed in place rigid urethane foam and fiberglass core
				d.	Hardware preparation:
					1)	Mortise, reinforce, drill, and tap doors at factory for fully templated mortised hardware only, in accordance with approved hardware schedule and supplied templates.
					2)	Provide reinforcing plates at surface-mounted or non-templated hardware locations.
				e.	Glazing Moldings and stops:
					1)	Wood moldings fastened to door on security side.
					2)	Loose stops, countersunk for fasteners.
					3)	Form moldings with mitered corner joints.
				f.	Glazed lites: Factory-assemble lites in doors indicated to have lites, using glazing materials of the same ballistic level specified for the door and frame.
	** NOTE TO SPECIFIER ** HM frames are suitable for UL 752 Levels 1 to 8.
			3.	HM Door Frames: Welded units with integral trim, of sizes and profiles indicated and as follows:
	** NOTE TO SPECIFIER ** Steel frames are available in multiple configurations including Wrap Frame, Split Frame, Butt Frame (for existing masonry/concrete openings), and Butt Frame for masonry built-in.
				a.	Frame Sizes and Configuration: As indicated on the Drawings.
				b.	Frames for interior use: Steel sheet, minimum 16 gage thickness, factory primed.
				c.	Stops: Minimum 5/8 inch (15.8 mm) in depth.
				d.	Contact edges of joints and mitered perimeter trim faces, continuously welded.
				e.	Hardware preparation:
					1)	Mortise, reinforce, drill, and tap frames at factory for fully templated mortised hardware, in accordance with approved hardware schedule.
					2)	Provide reinforcing plates at surface-mounted hardware locations.
				f.	Floor anchors:
					1)	Minimum 18 gage steel.
					2)	Weld anchors inside each jamb for floor anchorage.
				g.	Jamb anchors:
					1)	Weld anchors inside each jamb for wall anchorage.
					2)	Anchors of types suitable for adjacent wall construction.
				h.	Plaster guards: Minimum 26 gage galvanized steel; welded in place at hardware mortises on frames to be set in masonry or concrete openings.
				i.	Provide with temporary steel spreader welded to jamb feet for bracing during shipping and handling.
			4.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
				g.	UL 752 Level 7.
				h.	UL 752 Level 8.
	** NOTE TO SPECIFIER ** Select the bullet resistant transaction equipment required from the following paragraphs and delete those not required.
	2.8	BULLET RESISTANT TRANSACTION EQUIPMENT
		A.	Steel Package Receiver: 12 gauge steel, prime painted with UL Listed non-ricochet bullet resistant fiberglass in the doors offering the specified level of protection. Doors provided with interlocking mechanism, automatic door closer on the threat side door, threat side door lockout controlled from safe side, key locking on safe side door, and installation flanges as standard features.
			1.	Square Type Size:
	** NOTE TO SPECIFIER ** Select one of the following sizes from the following paragraphs as required. Delete the paragraph not required.
				a.	18 inches deep, 18 inches wide and 18 inches high.
				b.	18 inches deep, 24 inches wide and 24 inches high.
			2.	Door:
	** NOTE TO SPECIFIER ** Select one of the following door types from the following paragraphs as required. Delete the paragraph not required.
				a.	Steel sheet, 16 gauge, factory primed.
				b.	Stainless steel sheet, 18 gauge, with a No. 3 finish.
	** NOTE TO SPECIFIER ** The following paragraph is optional. Delete if not required.
				c.	Door Vision Panel: Safe side vision panel 6 inches by 6 inches. Laminated polycarbonate, minimum 1-1/4 inch thick with polished edges, conforms to offering the specified level of protection.
			3.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
		B.	Transparent Package Receiver: Laminated polycarbonate, minimum 1-1/4 inch thick with polished edges, conforms to offering the specified level of protection. Doors provided with interlocking mechanism, automatic door closer on the threat side door, threat side door lockout controlled from safe side, key locking on safe side door, and installation flanges as standard features.
			1.	Square Type Size:
	** NOTE TO SPECIFIER ** Select one of the following package receiver types from the following paragraphs as required. Delete the paragraphs not required.
				a.	14-1/2 inched deep, 14-1/2 inches wide and 14-1/2 inches high.
				b.	18 inches deep, 18 inches wide and 18 inches high.
			2.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
		C.	Rotary Package Receiver: High pressure laminated turntable and base with 12 gauge stainless steel outer body with UL Listed non-ricochet bullet resistant fiberglass offering the specified level of protection. Doors provided with night locking pin and rotating mechanism.
			1.	Size:
	** NOTE TO SPECIFIER ** Select one of the following package receiver types from the following paragraphs as required. Delete the paragraphs not required.
				a.	Turntable 16 inches in diameter on an 18 inch by 24 inch base and 20 inches high.
			2.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
		D.	Pivot Hopper: Body 12 gauge stainless steel with 16 gauge stainless steel flanges offering the specified level of protection. Stainless steel provided with a No. 3 finish. Doors provided with handle, safe latch, bumpers and pivot bolts.
			1.	Size:
				a.	16 inches wide by 10-1/8 inches high by 8 inches deep with 1 inch flanges.
			2.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
		E.	Money Cart Pass-Thru: Body 3/16 inch steel plate with 16 gauge steel flanges and UL Listed non-ricochet bullet resistant fiberglass offering the specified level of protection. All steel surfaces shop primed. Doors provided with continuous gear hinges, Falcon X581 locksets, Von Duprin 6211DS fail safe secure electric strikes.
			1.	Size:
				a.	42-3/8 inches wide by 42 inches high by 52 inches deep.
			2.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
		F.	Bullet Resistant Sliding Transaction Drawer: Steel, 16 gauge, painted case, stainless steel drawer front, stainless steel drawer and 16 gauge stainless steel flange frame with UL Listed non-ricochet bullet resistant fiberglass offering the specified level of protection. Stainless steel provided with a No. 3 finish. Drawer provided with sliding tracks and stainless steel release handle.
			1.	Size:
	** NOTE TO SPECIFIER ** Select one of the following drawer sizes as required. Delete the ones not required.
				a.	21-3/4 inches wide by 7-3/4 inches high by 24 inches deep with a 12 maximum travel drawer opening projection. Provided with key locking cash tray.
				b.	21-3/4 inches wide by 13-1/4 inches high by 24 inches deep with a 12 maximum travel drawer opening projection. Provided with key locking cash tray.
				c.	21-3/4 inches wide by 13-1/4 inches high by 24 inches deep with a 12 maximum travel drawer opening projection.
			2.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
		G.	Bullet Resistant Sliding Transaction Drawer with Dip Tray and Drawer Cover: Steel, 16 gauge, painted case, 12 gauge stainless steel drawer front, 12 gauge stainless steel top and front, stainless steel drawer and 16 gauge stainless steel flange frame, 16 gauge stainless dip tray, and stainless steel sliding drawer cover with UL Listed non-ricochet bullet resistant fiberglass offering the specified level of protection. Stainless steel provided with a No. 3 finish. Drawer provided with sliding tracks, perforated speaker opening in face panel and stainless steel actuating handle.
			1.	Size:
				a.	24 inches wide by 7-3/4 inches high by 24 inches deep with a 10-1/2 maximum travel drawer opening projection.
	** NOTE TO SPECIFIER ** Select the following optional accessories as required. Delete the ones not required.
			2.	Accessories:
				a.	Provide with speaker/microphone.
				b.	Transaction Window: Size as indicated on the Drawings. Frame and glazing provided to match the specified level of protection.
			3.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
		H.	Bullet Resistant Sliding Transaction Drawer with Hinged Drawer Front: Stainless steel 12 gauge flange and hood, 12 gauge stainless steel top hinged drawer front, 12 gauge stainless housing with UL Listed non-ricochet bullet resistant fiberglass offering the specified level of protection. Drawer lid fabricated of 1/2 inch thick lexan. Stainless steel provided with a No. 3 finish. Drawer provided with ball bearing sliding tracks, removable locking pin and stainless steel actuating handle.
			1.	Size:
				a.	19-5/8 inches wide by 11 inches high by 24-3/8 inches deep with a 5 inch maximum travel drawer opening projection.
	** NOTE TO SPECIFIER ** Select the following optional accessories as required. Delete the ones not required.
			2.	Accessories:
				a.	Transaction Window: Size as indicated on the Drawings. Frame and glazing provided to match the specified level of protection.
			3.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
		I.	Dip Tray:
	** NOTE TO SPECIFIER ** Select tray type required from the following paragraphs and delete the ones not required.
			1.	Dip Tray Recessed: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under of no less than 1-1/2 inches. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
			2.	Dip Tray with Weather Flap: Model RMDT1016, 10 inches by 16 inches from the outside edge of flanges with a clear open depth under of no less than 1-1/2 inches. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
			3.	Dip Tray Recessed: Model RMDT1012, 10 inches by 12 inches from the outside edge of flanges with a clear open depth under of no less than 1-1/2 inches. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
			4.	Dip Tray Surface Mount: Model SMDT1012, 10 inches by 12 inches from the outside edge with a clear open depth under of no less than 1-1/2 inches. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
			5.	Dip Tray Non-Ricochet: Model RMDT1012, 10 inches by 12 inches from the outside edge of flanges with a clear open depth under of no less than 1-3/4 inches. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
			6.	Dip Tray One-Way Non-Ricochet: Model RMDT1012, 10 inches by 12 inches from the outside edge of flanges with a clear open depth under of no less than 1-3/4 inches. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
			7.	Dip Tray with Flip Lid: Model RMDT1416, 14-1/2 inches by 16-5/8 inches from the outside edge of flanges with a clear open depth under of no less than 2-9/16 inches. Fabricate of a minimum 16 gauge stainless steel, with a No. 3 finish.
	** NOTE TO SPECIFIER ** Select the bullet resistant speaker and gun port products required from the following paragraphs and delete those not required.
	2.9	BULET RESISTANT SPEAKERS AND GUN PORTS
		A.	Bullet Resistant Speaker: Model SSBRS-7, 12 gauge stainless steel perforated speaker face and clamp plate with a No. 3 finish. Safe side provided with UL Listed Level 3 bullet resistant polycarbonate. Provided with 1/4 inch diameter stainless steel screws and space nuts to maintain a 7/8 inch clearance.
			1.	Size:
				a.	7 inch diameter.
		B.	Universal Bullet Resistant Speaker: Model SSS-7D, 12 gauge stainless steel perforated speaker face and clamp plate with a No. 3 finish. Provided with 1/4 inch diameter stainless steel screws and space nuts to maintain a 7/8 inch clearance.
			1.	Size:
				a.	7 inch diameter.
		C.	Universal Bullet Resistant Speaker: Model SSS-7S, 12 gauge stainless steel perforated speaker face and clamp plate with a No. 3 finish. Provided with 1/4 inch diameter stainless steel screws and space nuts to maintain a 7/8 inch clearance.
			1.	Size:
				a.	7 inch diameter.
		D.	Universal Bullet Resistant Speaker with Contraband Baffle: Model SSS-7D-3, 12 gauge stainless steel perforated speaker face and clamp plate with a No. 3 finish. Provided with contraband baffle, 1/4 inch diameter stainless steel screws and space nuts to maintain a 7/8 inch clearance.
			1.	Size:
				a.	7 inch diameter.
		E.	Bullet Resistant Speaker: Model SQ-BRS-6, 12 gauge stainless steel face and clamp plate with a No. 3 finish. Provided with 1/4 inch diameter stainless steel screws and neoprene spacers.
			1.	Size:
				a.	6 inches by 6 inches.
			2.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
		F.	Bullet Resistant Speaker: Model SSBRS-7, Safe side Armortex Hi-Hard Level 4 Ballistic Steel prime painted, 12 gauge stainless steel perforated face and clamp plate with a No. 3 finish. Provided with 1/4 inch diameter stainless steel screws and spacer nuts.
			1.	Size:
				a.	7 inch diameter.
			2.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
		G.	Bullet Resistant Pivot Gun Port: Model SSBRS-8, 12 gauge stainless steel face and back plate, 1/4 inch stainless steel pivot plate, with a No. 3 finish. Provided with 1/4 inch diameter stainless steel screws and spacer nuts, pivot, removable locking pin, stop and knob.
			1.	Size:
				a.	8 inch diameter.
			2.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
		H.	Bullet Resistant Pivot Gun Port: Model SSGP-8, 12 gauge stainless steel face and back plate, 1/4 inch prime finished ballistic steel pivot plate and support plate. Stainless steel provided with a No. 3 finish. Provided with 1/4 inch diameter stainless steel screws and spacer nuts, pivot, removable locking pin, stop and knob.
			1.	Size:
				a.	8 inch diameter.
			2.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
		I.	Bullet Resistant Sliding Gun Port: 14 gauge prime painted steel base, 16 gauge prime painted steel casing, ballistic steel or composite backing to suit resistance level specified, square 1/2 inch by 12 inch square tubes. Provided with springs, and locking latch.
			1.	Size:
				a.	8 inches by 5 inches including flanges.
			2.	Opening Security Level: Withstand bullet resistance level as follows, in accordance with UL 752.
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL 752 Level 1.
				b.	UL 752 Level 2.
				c.	UL 752 Level 3.
				d.	UL 752 Level 4.
				e.	UL 752 Level 5.
				f.	UL 752 Level 6.
	** NOTE TO SPECIFIER ** Select the bullet resistant and detention glazing products required from the following paragraphs and delete those not required. Armortex® Bullet Resistant and Detention Glazing is available in several configurations. High performance, multi-ply polycarbonate laminates are offered where both a lightweight and an attack resistant barrier is required. They are offered as Bullet Resistant products or as containment/forced entry barriers.
	2.10	BULLET RESISTANT AND DETENTION GLAZING
		A.	Bullet Resistant Glazing
			1.	Performance: UL 752, UL-1 (MPSA) 9 mm 124 Gr., FMJ 1175-1295 fps
				a.	TC 100: Laminated Glass/Airspace/ Laminated Polycarbonate, nominal thickness 13/16 inch (21 mm), nominal weight 5.3 lbs/SF (25.9 kg/sm).
				b.	TP 100: Polycarbonate Acrylic Composite, nominal thickness 3/4 inch (19 mm), nominal weight 5.1 lbs/SF (24.9 kg/sm).
				c.	BRG 100: Multi-Ply Laminated Glass, nominal thickness 1-3/16 inch (30 mm), nominal weight 18 (39.7 kg/sm).
				d.	GCP 100: Glass/Polycarbonate Composite, nominal thickness 3/4 inch (19 mm), nominal weight 8.4 lbs/SF (41 kg/sm).
			2.	Performance: UL 752, UL-2 (HPSA) .375 Mag. 158 Gr. Sp or Lead 1250-1375 fps
				a.	TC 200: Laminated Glass/Airspace/ Laminated Polycarbonate, nominal thickness 15/16 (24 mm), nominal weight 6.3 lbs/SF (30.7 kg/sm).
				b.	BRG 200: Multi-Ply Laminated Glass, nominal thickness 1-1/2 inch (38 mm), nominal weight 23 lbs/SF (112 kg/sm).
				c.	GCP 200: Glass/Polycarbonate Composite, nominal thickness 15/16 inch (24 mm), nominal weight 11.2 lbs/SF (54.7 kg/sm).
			3.	Performance: UL 752, UL-3 (SPSA) 44 Mag. 240 Gr. Sp 1350-1485 fps
				a.	TC 300: Laminated Glass/ Airspace/ Laminated Polycarbonate, nominal thickness 1-3/16 inch (30 mm), nominal weight lbs/SF 9.3 (45.4 kg/sm).
			4.	Performance: UL 752, UL-3 And UL-6 9mm 124 Gr. FMJ 1400-1540 fps 5 Shot
				a.	TP 300: Multi-Ply Polycarbonate, nominal thickness 1-1/4 inch (32 mm), nominal weight lbs/SF 8 (39 kg/sm).
			5.	Performance: UL 752, UL-3 (SPSA) 44 Mag. 240 Gr. Sp 1350-1485 fps
				a.	BRG 300: Multi-Ply Laminated Glass, nominal thickness 2-1/8 inch (54 mm), nominal weight 32 lbs/SF (156 kg/sm).
			6.	Performance: UL 752, UL-3 (SPSA) 44 Mag. 240 Gr. Sp 1350-1485 fps
				a.	GCP 300: Glass/Polycarbonate Composite, nominal thickness 1-3/16 inch (30 mm), nominal weight 13.2 lbs/SF (64 kg/sm).
			7.	Performance: UL 752, UL-4 (HPR) .30 Cal Rifle 180 Gr. Sp 1350-1485 fps
				a.	GCP 400: Glass/Polycarbonate Composite, nominal thickness 1-1/4 inch (32 mm), nominal weight 13.6 (66 kg/sm).
				b.	BRG 400: Multi-Ply Laminated Glass, nominal thickness 2-1/8 inch (54 mm), nominal weight 32 lbs/SF (156 kg/sm).
		B.	Forced Entry and Detention Glazing:
			1.	Performance: H.P. White Level-1 HPW-TP-0500-02
				a.	PC 10: Monolithic Polycarbonate with Hardcoat, nominal thickness 1/2 inch (13 mm), nominal weight 3.1 lbs/SF (15 kg/sm).
			2.	Performance: H.P. White Level-1 HPW-TP-0500-02
				a.	GCP 10: Glass/ Polycarbonate/ Glass Composite, nominal thickness 9/16 inch (14 mm), nominal weight 5.1 lbs/SF (24.9 kg/sm).
			3.	Performance: Southwest Research 02-5845-134
				a.	D II: Laminated Glass/ Airspace/ Polycarbonate/ Airspace Laminated Glass, nominal thickness 1-5/8 inch (41 mm), nominal weight 8.9 lbs/SF (43.4 kg/sm).
			4.	Performance: H.P. White Level-A-II
				a.	GCP 20: Glass/ Polycarbonate/ Glass Composite, nominal thickness 11/16 inch (17 mm), nominal weight 6.1 lbs/SF (29.8 kg/sm).
			5.	Performance: H.P. White A-I and WMFL III (30 Minute Containment)
				a.	PL 30: Multi-Ply Polycarbonate with Hardcoat, nominal thickness 3/8 inch (10 mm), nominal weight 2.5 lbs/SF (12.2 kg/sm).
			6.	Performance: H.P. White A-II HPW-TP-0500-02
				a.	GCP 30: Glass/Multi-Ply Polycarbonate/ Glass Composite Multi-Ply, nominal thickness 13/16 inch (21 mm), nominal weight 6.3 lbs/SF (30.7 kg/sm).
			7.	Performance: H.P. White A-I and WMFL II (60 Minute Containment)
				a.	PL 60: Polycarbonate with Hardcoat, nominal thickness 1/2 inch (13 mm), nominal weight 3.3 lbs/SF (16.1 kg/sm).
			8.	Performance: H.P. White Level A-IV HPW-TP-0500-02
				a.	GCP 60: Glass/Multi-Ply Polycarbonate/ Glass Composite, nominal thickness 15/16 inch (24 mm), nominal weight 7 lbs/SF (34.2 kg/sm).
	2.11	BULLET RESISTANT COMPOSITE PANELS
		A.	Composite Panels: Armortex Bullet and Blast Protection Composite Panels. FRP composite panel manufactured using multiple layers of starch-oil woven roving ballistic grade fiberglass cloth impregnated with a thermoset polyester resin and compressed into flat rigid sheets.
			1.	Composite panels shall be of the "non ricochet type" intended to permit the encapture and retention of an attacking projectile lessening the potential of a random injury or lateral penetration.
			2.	Material will meet ASTM E 119 one hour fire resistance when installed in a non-bearing steel stud wall with 5/8 inch firecode gypsum on the exterior and with 5/8 inch firecode gypsum over the FRP panel on the inside.
			3.	Panels conforming to UL 752 Rating level as follows:
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	UL Level I: Armortex OF 100.
				b.	UL Level 2: Armortex OF 200.
				c.	UL Level 3: Armortex OF 300.
				d.	UL Level 4: Armortex OF 400.
				e.	UL Level 5: Armortex OF 500.
				f.	UL Level 6: Armortex OF 600.
				g.	UL Level 7: Armortex OF 700.
				h.	UL Level 8: Armortex OF 800.
			4.	Panels conforming to National Institute of Justice (N.I.J) 0108.01 Threat Level Rating as follows:
	** NOTE TO SPECIFIER ** Select one of the following security levels as required. Delete the security levels not required.
				a.	N.I.J Level I: Armortex A-1.
				b.	N.I.J Level IA-A: Armortex A-2.
				c.	N.I.J Level II: Armortex O.F.200.
				d.	N.I.J Level __: Armortex A-3.
				e.	N.I.J Level III-A: Armortex O.F.300.
				f.	N.I.J Level __: Armortex A-4.
				g.	N.I.J Level III: Armortex O.F. 800.
	2.12	FABRICATION
		A.	All welds shall be in accordance with the requirements and standard practices of the American Welding Society. All exposed welds shall be ground flush and finished smooth.
		B.	All joints and connections shall be tight, providing hairline joints and true alignment of adjacent members.
	PART 3	EXECUTION
	3.1	EXAMINATION
		A.	Do not begin installation until openings and installing surfaces have been properly prepared.
		B.	Verify openings are in accordance with approved shop drawings
		C.	Verify that all supports have been installed in accordance with the Drawings.
		D.	If preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
	3.2	PREPARATION
		A.	Clean surfaces thoroughly prior to installation.
		B.	Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
	3.3	INSTALLATION
		A.	Install in accordance with manufacturer's instructions and requirements of UL 752.
		B.	Install all equipment plumb, level, rigid and in true alignment.
		C.	Set equipment in accordance with the manufacturer's printed recommendations. Use proper anchoring devices for the material to be anchored to. All exposed anchor holes shall be used for anchoring.
		D.	Install fire-rated assemblies in accordance with NFPA 80.
		E.	Bullet Resistant Fiberglass panels can be installed using an industrial adhesive, mastic, screws or bolts. Method of application shall maintain the bullet resistive rating at junctures with the concrete floor slab, concrete roof slab, bullet resistive door frames, bullet resistive window frames, and all required penetrations.
			1.	All joints reinforced by a back-up layer of bullet resistive material.
			2.	Bullet resistance of the joint, as reinforced, shall be at least equal to that of the panel.
			3.	Minimum width of reinforcing layer at joint shall be 4 inches (2 inches on each panel or a 2 inch minimum overlap).
		F.	Install hardware as specified in Section 08710 in accordance with the hardware manufacturer's recommendations and templates.
		G.	Field painting is specified in Section 09900.
		H.	Installation tolerances: Do not exceed the following installation tolerances:
			1.	Squareness: Plus or minus 1/16 inch (1.6 mm) measured on a line, 90 degrees from one jamb, at the upper corner of the frame at the other jamb.
			2.	Alignment: Plus or minus 1/16 inch (1.6 mm) measured on jambs on a horizontal line parallel to the plane of the wall.
			3.	Twist: Plus or minus 1/16 inch (1.6 mm) measured at face corners of jambs on parallel lines perpendicular to the plane of the wall.
			4.	Plumb: Plus or minus 1/16 inch (1.6 mm) measured on the jamb at the floor.
		I.	Adjust installed doors for correct swings and site tolerances.
		J.	Adjust installed for smooth non-binding operation and site tolerances.
	3.4	PROTECTION
		A.	Protect installed products until completion of project.
		B.	Touch-up, repair or replace damaged products before Substantial Completion.
	3.5	SCHEDULES
	** NOTE TO SPECIFIER ** Retain Paragraph below if required to suit project requirements. Identify products by name on the Drawings or use this paragraph to define the location of each type of material to be used. The following are some examples of schedule references. Edit as required to suit project or delete and identify products on the Drawings.
		A.	:
		B.	:
	END OF SECTION