MasterFormat: 95

SpecWizard: customize this spec    Download this Raceway and Boxes Specification for   WORD | WP | RTF | TEXT

Find over 500 more construction specifications | Arcat.com

	SECTION 16130
	RACEWAY AND BOXES
	** NOTE TO SPECIFIER ** Wiremold/Legrand; Surface raceways, indoor service poles, multi-service in-wall boxes, floor boxes, poke-thru systems, cable tray systems, underfloor ducts with junction boxes. . This section is based on the products of Wiremold/Legrand, which is located at: 60 Woodlawn Street West Hartford CT 06133-2500 Tel. (800) 621-0049 Fax. (203) 232-2062 Email: sales@wiremold.com Web: www.wiremold.com. . Wiremold/Legrand offers a complete line of products for communications, data, and electrical wiring management.
	PART 1	GENERAL
	1.1	SECTION INCLUDES
	** NOTE TO SPECIFIER ** Delete items below not required for project.
		A.	Surface Metallic Raceways.
		B.	Surface Non-Metallic Raceways.
		C.	Architectural Service Columns.
		D.	Indoor Service Poles.
		E.	Multi-Service In-Wall Box.
		F.	Floor Boxes.
			1.	Floor boxes for on-grade and above-grade concrete floors.
			2.	Fire-classified floor boxes for on-grade and above-grade concrete floors.
			3.	Floor boxes for raised floors.
			4.	Floor boxes for wood floors.
		G.	Fire Stop Thru-Wall/Thru-Floor Fittings
		H.	Poke-Thru Systems.
		I.	Cable Tray Systems.
		J.	Raceway and Enclosures for Secure Network Installations.
	1.2	RELATED SECTIONS
	** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
		A.	Section 07840 - Penetration Firestopping Devices.
		B.	Section 16050 - Basic Electrical Materials and Methods: Electrical systems and components.
		C.	Section 16053 - Electronic Safety and Security: Security systems and components.
		D.	Section 16700 - Communications: Communications systems and components.
	1.3	REFERENCES
	** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
		A.	NFPA 70 - National Electrical Code.
		B.	UL 5 - Surface Metal Raceways and Fittings.
		C.	UL 94 - Test for Flammability of Plastic Materials for Parts in Devices and Appliances.
	1.4	SUBMITTALS
		A.	Submit under provisions of Section 01300.
		B.	Product Data: Manufacturer's data sheets and descriptive literature on each product to be used, including:
			1.	Preparation instructions and recommendations.
			2.	Storage and handling requirements and recommendations.
			3.	Installation methods.
		C.	Shop Drawings: Indicate raceway layouts, each system component required for complete system, raceway lengths, device types, locations; identify all circuits.
		D.	Samples:
			1.	Submit three 6-inch lengths of exposed type surface raceways with required color and finish. Show standard color ranges available.
			2.	Submit service pole and architectural column samples with required color and finish. Show standard color ranges available.
		E.	Test Reports: Certified reports from independent testing laboratory supporting compliance of raceway system to specified requirements.
		F.	Manufacturer's instructions: Printed installation instructions for each system component; include storage requirements.
		G.	Project Record Documents: If variations from approved shop drawings occur during installation of raceway system, submit final as-built drawings indicating such variations.
	1.5	QUALITY ASSURANCE
	** NOTE TO SPECIFIER ** In this article, describe qualifications, regulatory requirements, certifications, field samples, mock-ups, and pre-installation meetings.
		A.	Manufacturer Qualifications: Firms regularly engaged in manufacture of raceway and box distribution products and systems of the types and sizes required, whose products have been in satisfactory use in similar service for not less than 10 years. Provide raceway and box distribution systems produced Wiremold/Legrand.
		B.	Source Limitation: Obtain each type of round recessed raised and stage floor box through one source from a single manufacturer.
	** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.
		C.	Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.
			1.	Finish areas designated by Architect.
			2.	Do not proceed with remaining work until workmanship, appearance and performance are approved by Architect.
			3.	Refinish mock-up area as required to produce acceptable work.
		D.	Electrical Components, Devices, and Accessories: Comply with requirements of applicable local codes, NEC, UL, and NEMA Standards pertaining to indoor service poles and architectural columns. Listed and labeled in accordance with NFPA 70, Article 100.
		E.	Electrical Floor Boxes and Components: Comply with requirements of applicable local codes, NEC, UL, and NEMA Standards pertaining to floor boxes and components. Meet or exceed UL Fire Classification requirements for recessed and flush style boxes. Listed and labeled in accordance with NFPA 70, Article 100.
		F.	Products: Listed and classified by Underwriters Laboratories, Inc. as suitable for the purpose specified and indicated.
		G.	Accessibility Compliance: Design device flange to meet ADA Accessibility Guidelines as to changes in floor and ground surface levels. Flanges shall be beveled so the slope is no greater than 1:2.
	1.6	DELIVERY, STORAGE, AND HANDLING
		A.	Store products in manufacturer's unopened packaging until ready for installation.
		B.	Store and handle in strict compliance with manufacturer's written instructions and recommendations.
		C.	Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.
		D.	Protect from damage due to weather, excessive temperature, and construction operations.
	1.7	PROJECT CONDITIONS
		A.	Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.
	PART 2	PRODUCTS
	2.1	MANUFACTURERS
		A.	Acceptable Manufacturer: Wiremold/Legrand, which is located at: 60 Woodlawn St. ; West Hartford, CT 06110; Toll Free Tel: 800-621-0049; Tel: 860-233-6251; Email: request info; Web: www.wiremold.com
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
		B.	Substitutions: Not permitted.
		C.	Requests for substitutions will be considered in accordance with provisions of Section 01600, and should include documentation of UL listings and a sample of components.
	** NOTE TO SPECIFIER ** Delete if not required.
	2.2	SURFACE METALLIC RACEWAYS
	** NOTE TO SPECIFIER ** Dimensions provided refer to assembled dimensions.
		A.	General:
			1.	System: Provide surface raceway systems for branch circuit and data network voice, video and other low-voltage wiring. Surface raceway system shall consist of raceway bases, covers, appropriate fittings and device mounting plates necessary for a complete installation.
			2.	Configuration: Raceways shall be one- or two-piece design with base and snap-on cover, or three-piece design with base and two snap-on covers which snap side by side on a common base. Base shall be dividable with a fixed barrier for up to 4 compartments. Raceway shall be available in widths of 3/4 inch to 10 inches (19 mm to 254 mm) and depths of 17/32 inch to 5 inches (13.5 mm to 127 mm) Provide raceways from a company which can provide custom sizes if required. Raceway covers shall be available in tamper-resistant form with screws on access plates and covers of fittings, but not on standard cover lengths.
			3.	Fittings: Fittings shall include flat, internal and external elbows, couplings for joining raceway sections, wire clips, blank end fittings, and device mounting brackets and plates as applicable. Where required, provide tamper-resistant form, dividable with barriers and matching the size of the accompanying raceway base. Provide full capacity corner elbows and tee fittings to maintain a controlled 2 inch cable bend radius, meeting the specification for Fiber Optic and UTP cabling and exceeding the TIA/EIA-569-A requirements for communications pathways.
			4.	Device Brackets and Plates: Provide in sizes to match the raceway width and with mounting holes located to ensure proper mounting of devices in up to 4 compartments. Device plates shall be available in any length from 6 inch to 60 inch, with cutouts to accommodate various combinations of power and communications devices in up to 4 compartments. Provide 6 inch and 12 inch long device plates with a flange to overlap the joint of adjacent cover as applicable.
			5.	Communications Devices and Accessories: Raceway shall accommodate a complete line of connectivity outlets and modular inserts for UTP (including Category 5, 5e, 6) STP (150 ohm) fiber optic, coaxial, and other cabling types with matching faceplates and bezels to facilitate mounting. Where indicated, provide connectivity outlets and modular inserts by Ortronics or approved equal.
		B.	Classification:
			1.	Raceway and system components shall be UL and CUL listed.
			2.	Surface raceways shall be suitable for use in dry interior locations only, as covered in Article 386 (Surface Metal Raceways) 388 (Surface Nonmetallic Raceways) of the National Electrical Code.
			3.	Surface metal raceways and fittings shall be listed by Underwriters Laboratories under File Number E4376, Listing and Classification Number RJBT and File Number E41751, Listing and Classification Number RJPR respectively.
			4.	Systems shall comply with UL Standard UL5 for Surface Metal Raceways.
			5.	Larger 2 and 3 channel non-metallic raceways shall be UL Listed under File Nos. E90378 Guide RJTX and E90377 Guide RJYT, respectively.
		C.	Product Requirements: Surface metallic raceway for dry interior locations, conforming to National Electrical Code, Article 352, Part B.
			1.	Metal Components: UL listed, conforming to specifications of UL 5.
			2.	Plastic Components: UL listed, exhibiting non-flammable, self-extinguishing characteristics when tested in accordance with UL 94, V-O.
		D.	Surface Metallic Raceways: Two-piece system; type 304 stainless steel with number 4 brush finish, consisting of a base and snap-on cover.
	** NOTE TO SPECIFIER ** The following raceway is available prewired. Please refer to Prewired Raceways paragraph.
			1.	Acceptable Product: Wiremold S4000 Dual-Channel Stainless Steel Raceway by Wiremold/Legrand.
				a.	Construction: 0.050 inch (1 mm) thick stainless steel; base has two 9/32 inch (7 mm) diameter knockouts on 18 inch (457 mm) centers; 4-3/4 inches (121 mm) wide by 1-3/4 inches (44 mm) deep.
		E.	Surface Metallic Raceways: Two-piece system of galvanized steel consisting of a base and snap-on cover.
	** NOTE TO SPECIFIER ** Delete the following acceptable product paragraphs not required by project. If more than one is specified, indicate where each is to be used.
			1.	Acceptable Product: Wiremold 2000 Series Two-Piece Single-Channel Metal Raceway by Wiremold/Legrand.
				a.	Construction: 0.040 inch (1 mm) metal thickness; 1-9/32 inches (33 mm) wide by 3/4 inch (19 mm) deep; downward facing devices, bend radius control fittings.
				b.	Finish: Manufacturer’s standard Ivory, Gray or custom color as selected.
			2.	Acceptable Product: Wiremold 2400 Series Two-Piece Metal Raceway by Wiremold/Legrand.
				a.	Construction: 0.040 inch (1 mm) metal thickness; 1-7/8 inches (48 mm) wide by 7/8 inch (22 mm) deep; downward facing devices, bend radius control fittings.
				b.	Finish: Manufacturer’s standard Ivory, Fog White or custom color as selected.
			3.	Acceptable Product: Wiremold 2400D Series Two-Piece Dual-Channel Metal Raceway by Wiremold/Legrand.
				a.	Construction: 0.040 inch (1 mm) metal thickness; integral barrier divides raceway into 1/3 and 2/3 channels; 1-7/8 inches (48 mm) wide by 7/8 inch (22 mm) deep, downward facing devices, bend radius control fittings.
				b.	Finish: Manufacturer’s standard Ivory, Fog White or custom color as selected.
				c.	Finish: Factory-applied polyester topcoat applied over ivory base suitable for field-applied topcoat.
	** NOTE TO SPECIFIER ** The following two raceways (3000 and 4000) are available prewired. Please refer to Prewired Raceways paragraph for specifying.
			4.	Acceptable Product: Wiremold 3000 Series Single-Channel Metal Surface Raceway by Wiremold/Legrand.
				a.	Construction: 0.040 inch (1 mm) metal thickness; 2-3/4 inches (70 mm) wide by 1-15/32 inches (37 mm) deep, predrilled Kos in base sections.
				b.	Finish: Manufacturer’s standard Ivory, Gray or custom color as selected.
				c.	Finish: Factory-applied polyester topcoat applied over ivory base suitable for field-applied topcoat.
			5.	Acceptable Product: Wiremold 4000 Series Metal Raceway by Wiremold/Legrand.
				a.	Construction: 0.050 inch (1 mm) metal thickness; base has two 9/32 inch (7 mm) diameter knockouts on 18 inch (457 mm) centers; 4-3/4 inches (121 mm) wide by 1-3/4 inches (44 mm) deep, cross-section area 7.14 square inches (4606 square mm); bend radius control fittings, removable divider.
				b.	Finish: Manufacturer’s standard Ivory, Gray or custom color as selected.
				c.	Finish: Factory-applied polyester topcoat applied over ivory base suitable for field-applied topcoat.
			6.	Acceptable Product: Wiremold 6000 Series Metal Raceway by Wiremold/Legrand.
				a.	Construction: 0.060 inch (1.5 mm) metal thickness; base has two 9/32 inch (7 mm) diameter knockouts 1-1/4 inches (32 mm) apart on 18 inch (457 mm) centers; 4-3/4 inches (121 mm) wide by 3-9/16 inches (90 mm) deep, bend radius control fittings.
				b.	Finish: Manufacturer’s standard Ivory, Gray or custom color as selected.
				c.	Finish: Factory-applied polyester topcoat applied over ivory base suitable for field-applied topcoat.
		F.	Brackets and Faceplates:
			1.	Steel Device Brackets and Plates: Steel overlap device plate for horizontal installation of devices. Plate shall overlap cover to conceal seam.
			2.	Plastic Overlapping Cover Bracket and Faceplate: Plastic device mounting bracket and trim plate for horizontal installation of devices. Plate shall overlap cover to conceal seam. Faceplate shall accept a variety of power and data/communication devices. Plastic shall be compatible with UL 94 for Plastic.
		G.	Surface Mounted Metal Raceways:
			1.	Acceptable Product: Wiremold DS4000 Series Raceway Three-Piece Dual-Channel Steel Raceway by Wiremold/Legrand.
			2.	Material: Galvanized steel, minimum thickness 0.040 inch (1mm).
			3.	Finish:
				a.	Manufacturer's standard Designer Ivory (fog white), Designer Gray, Metallic Bronze or Matte Black or custom color as selected.
				b.	Factory-applied polyester topcoat applied over ivory base suitable for field-applied topcoat.
			4.	Steel Device Brackets and Plates: Steel overlap device plate for horizontal installation of devices. Plate shall overlap cover to conceal seam.
			5.	Plastic Overlapping Cover Bracket and Faceplate: Plastic device mounting bracket and trim plate for horizontal installation of devices. Plate shall overlap cover to conceal seam. Faceplate shall accept a variety of power and data/communication devices. Plastic shall be compatible with UL 94 for Plastic.
			6.	Adjustable Length Raceway Couplings: Provide raceway base sections with adjustable couplings. Each pair of couplings works in conjunction with the raceway base's scored lines to allow less accurate field cuts. The coupling shall accommodate 4 inches (102 mm) of lateral movement and facilitate the ability of the raceway to maintain coordination with the wall framing as required. Each coupling shall provide a means of adding supplemental ground screws.
			7.	Fittings: Fittings shall include flat, internal and external elbows, tees, entrance fittings, wire clips, cover clips, couplings, support clips, and end caps. Covers for fittings shall overlap adjoining raceway covers a minimum of 3/8 inch (10 mm). Fittings shall be color matched to the raceway. Supply fittings with a base where applicable to eliminate mitering. Provide fittings with adjustable couplings that integrate with the raceway base. Provide a take-off fitting supporting dual services to adapt to existing flush wall boxes and other series of metallic raceways. Fittings shall have provisions to accept tamper resistant fasteners to fully secure the raceway.
				a.	Fiber Optic/UTP/STP Fittings: Corner elbows, tees, and entrance end fittings as required to maintain a controlled 2 inches (51 mm) nominal cable bend radius that meets the specifications for Fiber Optic and UTP/STP cabling and exceeds TIA 569 requirements for communications pathways.
				b.	Obstacle Avoidance and Offset Fittings: Provide fittings as required to bypass large and small obstacles and small offsets in supporting wall. Small obstacle avoidance fitting capable of being converted into a take off fitting to transition to other metallic raceways.
			8.	Device Brackets and Plates:
				a.	Forward Fittings: Provide device brackets to install single-gang devices horizontally in either channel within the raceway. Provide horizontal device brackets with a single gang face plate. Horizontal device mounting brackets shall be a single piece with integral auxiliary grounding points. Device brackets and activation face plates shall allow the electrical or communications devices to face forward from the sidewall of the raceway.
				b.	Downward Fittings: Provide downward facing device brackets and face plates with internal tunneling devices to allow cabling to cross over the adjacent channel and exit the downward facing sidewall and maintain separation of services and full capacity of the specified channel. When this is provided, the maximum cable bend radius is 4 inches (102 mm). Devices for both power and data/communication shall have the capacity of mounting flush or in conjunction with face plates. The face plates shall be used to conceal seams between raceway cover and installed face plate. Device brackets and plates with any combination of multiple opening options and with any combination of multiple device opening options. Color match device brackets and plates to the raceway.
			9.	Communications Devices and Accessories: Raceway shall accommodate a complete line of connectivity outlets and modular inserts for UTP (including Category 5, 5e, 6) STP (150 ohm) fiber optic, coaxial, and other cabling types with matching faceplates and bezels to facilitate mounting. Provide with complete line of preprinted station and port identification labels.
		H.	Surface Metallic Raceways: One-piece system of galvanized steel, base and cover preassembled.
	** NOTE TO SPECIFIER ** Delete one of the following two acceptable product paragraphs if not required by project. If both are specified, indicate where each is to be used.
			1.	Acceptable Product: Wiremold 500 Series One Piece Metal Raceway by Wiremold/Legrand.
				a.	Construction: 3/4 inch (19 mm) wide by 17/32 inch (14 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory or custom color as selected.
			2.	Acceptable Product: Wiremold 700 Series One Piece Metal Raceway by Wiremold/Legrand.
				a.	Construction: 3/4 inch (19 mm) wide by 21/32 inch (17 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
		I.	Surface Metallic Raceways: Extruded aluminum alloy 6303-T5, minimum thickness 0.050 inches (1.27 mm) with surface finish of minimum .004 inch (0.1 mm) anodized satin Type 204 clear Class R1 Mil-Spec; UL listed.
	** NOTE TO SPECIFIER ** Delete the following acceptable product paragraphs not required by project. If more than one is specified, indicate where each is to be used.
			1.	Acceptable Product: Wiremold AL2000 Series Surface Metal Raceway by Wiremold/Legrand.
				a.	Construction: Tapered blank cover; 1-7/16 inches (36 mm) wide by 1-1/8 inches (28 mm) deep.
			2.	Acceptable Product: Wiremold AL2400 Series Surface Metal Raceway by Wiremold/Legrand.
				a.	Construction: Tapered blank cover; 2 inches (51 mm) wide by 1-9/32 inches (32 mm) deep.
			3.	Acceptable Product: Wiremold AL3300 Series Surface Metal Raceway by Wiremold/Legrand.
				a.	Construction: 0.040 inch (1 mm) galvanized steel field installed divider creates dual channels; 2-7/8 inches (73 mm) wide by 1-7/8 inches (36 mm) deep; field installable divider.
	** NOTE TO SPECIFIER ** Delete if not required.
				b.	Provide 1-13/16 inch (46 mm) high snap-in dividers.
	** NOTE TO SPECIFIER ** The following two raceways (ALA3800 and ALA4800) are also available prewired. Please refer to Surface Prewired Raceways paragraph for specifying.
			4.	Acceptable Product: Wiremold ALA3800 Series Surface Metal Raceway by Wiremold/Legrand.
				a.	Construction: 3 inches (76 mm) wide by 2-1/4 inches (57 mm) deep.
			5.	Acceptable Product: Wiremold ALA4800 Series Surface Metal Raceway by Wiremold/Legrand.
				a.	Construction: Base with integral barrier creating dual channels; twin removable snap covers, one per channel; 6 inches (152 mm) wide by 2-1/4 inches (57 mm) deep, bend radius control fittings.
			6.	Acceptable Product: Wiremold AL5200 Series Surface Metal Raceway by Wiremold/Legrand.
				a.	Construction: 5 inches (127 mm) wide by 2 inches (51 mm) deep; four ribs in base for adding snap-in divider; dual covers.
	** NOTE TO SPECIFIER ** Delete if not required.
				b.	Provide 1-13/16 inch (46 mm) high snap-in dividers.
			7.	Acceptable Product: Wiremold ALDS4000 Series Surface Three-Piece Single or Dual-Channel Metal Raceway by Wiremold/Legrand.
				a.	Construction: 0.060 inch (1.52 mm) galvanized steel creates dual channels; 2-7/8 inches (73 mm) wide by 2-1/8 inches (54 mm) deep; dual covers, .078 inch (2 mm) satin anodized aluminum, prescored base with KOs.
			8.	Adjustable Length Raceway Couplings: Provide raceway base sections with adjustable couplings. Each pair of couplings works in conjunction with the raceway base’s scored lines to allow less accurate field cuts. The coupling shall accommodate 4 inches (102 mm) of lateral movement and facilitate the ability of the raceway to maintain coordination with the wall framing as required. Each coupling shall provide a means of adding supplemental ground screws.
			9.	Fiber Optic/UTP/STP Fittings: Corner elbows, tees, and entrance end fittings as required to maintain a controlled 2 inches (51 mm) nominal cable bend radius that meets the specifications for Fiber Optic and UTP/STP cabling and exceeds TIA 569 requirements for communications pathways.
			10.	Forward Fittings: Provide device brackets to install single-gang devices horizontally in either channel within the raceway. Provide horizontal device brackets with a single gang face plate. Horizontal device mounting brackets shall be a single piece with integral auxiliary grounding points. Device brackets and activation face plates shall allow the electrical or communications devices to face forward from the sidewall of the raceway.
			11.	Communications Devices and Accessories: Raceway shall accommodate a complete line of connectivity outlets and modular inserts for UTP (including Category 5, 5e, 6) STP (150 ohm) fiber optic, coaxial, and other cabling types with matching faceplates and bezels to facilitate mounting. Provide with complete line of preprinted station and port identification labels.
			12.	In addition to specified fittings, provide device covers to mount duplex devices.
			13.	Device Cover Plates: Suitable to mount commercially available duplex devices, single 1.40 inches (36 mm) and 1.59 inches (40 mm) diameter receptacles. GFCI, surge receptacles and other rectangular faced devices, and voice and data jacks. Cover plates shall be removable using standard screwdriver without marring the finish.
		J.	Surface Metallic Raceways: Wiremold AnySize Raceway.
			1.	Construction: Bend radius control fittings, optional
	** NOTE TO SPECIFIER ** Delete the following paragraphs if not required for project.
			2.	Fittings: Tamper resistant.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
			3.	Material: Galvanized steel, minimum 0.04 inches (1.02 mm) thick.
			4.	Material: Aluminum, minimum 0.05 inches (1.27 mm) thick.
	** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. Raceway may or may not be painted.
			5.	Finish: Painted in field. Refer to Room Finish Schedule.
			6.	Finish: As selected by Architect.
			7.	Finish: No finish.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
			8.	Provide two-piece design with a base and snap on cover.
			9.	Provide three-piece design with common base and two side-by-side snap on covers.
	** NOTE TO SPECIFIER ** Delete three of the following four paragraphs.
			10.	Fixed Barrier Divider: For one compartment.
			11.	Fixed Barrier Divider: For two compartments.
			12.	Fixed Barrier Divider: For three compartments.
			13.	Fixed Barrier Divider: For four compartments.
			14.	Raceway Width: As indicated on drawings.
			15.	Raceway Depth: As indicated on drawings.
	** NOTE TO SPECIFIER ** Delete the following paragraphs not required by project.
			16.	Provide raceway covers in enhanced tamper resistant form, with screws only on access plates and covers of certain fittings, not on standard cover lengths.
			17.	In addition to specified fittings, provide full compliment of mounting devices and brackets in size to match width of raceway and length and cutouts to match raceway devices.
	** NOTE TO SPECIFIER ** If 6 inch (152 mm) or 12 inch (305 mm) long device plates are specified, specify the following paragraph. Delete the following paragraph if not required.
			18.	In addition to specified fittings, provide device plate with flange to overlap joint of adjacent cover.
		K.	Surface PreWired Metallic Raceways: Wiremold Prewired series; factory designed and wired.
	** NOTE TO SPECIFIER ** Delete the following acceptable product paragraphs not required by project. If more than one is specified, indicate where each is to be used.
			1.	Acceptable Product: DS4000 Series Prewired Three-Piece Dual-Channel Steel Raceway by Wiremold/Legrand.
				a.	Material: Galvanized steel, minimum thickness 0.040 inch (1mm).
				b.	Finish:
					1)	Manufacturer's standard Designer Ivory (fog white), Designer Gray, Metallic Bronze or Matte Black or custom color as selected.
					2)	Factory-applied polyester topcoat applied over ivory base suitable for field-applied topcoat.
			2.	Acceptable Product: Wiremold 3000 Series Single-Channel Metal Raceway by Wiremold/Legrand.
				a.	Construction: Galvanized steel; base and snap-fit cover; 0.040 inch (1 mm) metal thickness; 2-3/4 inches (70 mm) wide by 1-15/32 inches (37 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, Gray or custom color as selected.
			3.	Acceptable Product: Wiremold 4000 Series Single- or Dual-Channel Raceway by Wiremold/Legrand.
				a.	Construction: Galvanized steel; base and snap fit cover; 0.050 inch (1 mm) metal thickness; base has two 9/32 inch (7 mm) diameter knockouts on 18 inch (457 mm) centers; 4-3/4 inches (121 mm) wide by 1-3/4 inches (44 mm) deep, cross-section area 7.14 square inches (4606 square mm).
				b.	Finish: Manufacturer’s standard Ivory, Gray or custom color as selected.
			4.	Acceptable Product: Wiremold Isoduct Single and Multiple Channel Prewired Aluminum Raceway AL4320 by Wiremold/Legrand.
				a.	Construction: 6303-T5 aluminum alloy; two channel base with integral divider; two snap fit covers, one cover per channel; 5-1/4 inches (133 mm) wide by 1-3/4 inches (45 mm) deep, snap off internal barriers.
			5.	Acceptable Product: Wiremold Isoduct Single and Multiple Channel Prewired Aluminum Raceway AL3000 by Wiremold/Legrand.
				a.	Construction: 6303-T5 aluminum alloy; base and snap-fit cover; 2-5/8 inches (29 mm) wide by 1-3/4 inches (45 mm) deep.
			6.	Acceptable Product: Wiremold Isoduct Single and Multiple Channel Prewired Aluminum Raceway AL4000 by Wiremold/Legrand.
				a.	Construction: 6303-T5 aluminum alloy; two channel base with integral divider; snap fit cover; 4-3/4 inches (121 mm) wide by 1-3/4 inches (45 mm) deep, bend internal barriers. Bend radius control fittings.
			7.	Acceptable Product: Wiremold Isoduct Single and Multiple Channel Prewired Aluminum Raceway AL4400 by Wiremold/Legrand.
				a.	Construction: 6303-T5 aluminum alloy; two channel base integral divider; snap fit cover; 4-3/4 inches (121 mm) wide by 2-1/4 inches (57 mm) deep, snap off internal barriers.
			8.	Acceptable Product: Wiremold Isoduct Single and Multiple Channel Prewired Aluminum Raceway AL4520 by Wiremold/Legrand.
				a.	Construction: 6303-T5 aluminum alloy; two channel base with integral divider; two snap fit covers, one cover per channel; 5-1/4 inches (133 mm) wide by 2-1/4 inches (57 mm) deep, snap off internal barriers.
			9.	Acceptable Product: Wiremold Isoduct Single and Multiple Channel Prewired Aluminum Raceway AL7320 by Wiremold/Legrand.
				a.	Construction: 6303-T5 aluminum alloy; three channel base with integral dividers; two snap-fit covers; one cover fits two channels, second cover fits one channel; 7-3/8 inches (187 mm) wide by 1-3/4 inches (45 mm) deep.
			10.	Acceptable Product: Wiremold Isoduct Single and Multiple Channel Prewired Aluminum Raceway AL7450 by Wiremold/Legrand.
				a.	Construction: 6303-T5 aluminum alloy; three channel base with integral dividers; two snap-fit covers; one cover fits two channels, second cover fits one channel; 7-3/8 inches (187 mm) wide by 2-1/4 inches (45 mm) deep.
			11.	Acceptable Product: Wiremold Isoduct Single and Multiple Channel Prewired Aluminum Raceway AL4750 by Wiremold/Legrand.
				a.	Construction: 6303-T5 aluminum alloy; two channel base with integral divider creating 1-1/4 inch (32 mm) and 2 inch (51 mm) wide channels; snap fit cover; 3-1/4 inches (83 mm) wide by 1-7/8 inches (48 mm) deep, bend internal barriers.
			12.	Acceptable Product: Wiremold ALA3800 Isoduct Architectural Aluminum Single Channel Raceway by Wiremold/Legrand.
				a.	Design: Single service aluminum raceway, with cover.
				b.	Conforms to UL, NEC, and NEMA standards and EIA/TIA recommendations.
			13.	Acceptable Product: Wiremold ALA4800 Isoduct Architectural Aluminum Twin Cover Raceway by Wiremold/Legrand.
				a.	Design: Dual service aluminum raceway, with twin covers and a built-in divider
				b.	Conforms to UL, NEC, and NEMA standards and EIA/TIA recommendations, bend internal barriers.
			14.	Acceptable Product: Wiremold ALDS4000 Designer Series Aluminum Raceway by Wiremold/Legrand.
				a.	Design: Dual service aluminum raceway, with twin covers and a built-in divider.
				b.	Construction: Bend radius control fittings, adjust-to-fit couplings, downward facing devices, prescored base, predrilled KOs in base.
				c.	Conforms to UL, NEC, and NEMA standards and EIA/TIA recommendations.
	** NOTE TO SPECIFIER ** The following paragraph applies to aluminum raceways. Delete if not required.
			15.	Finish: Minimum .004 inch (0.1 mm) anodized satin Type 204 clear Class R1 Mil-Spec
			16.	Devices: Factory installed wiring and connectors.
			17.	Receptacle Labels: Provide receptacles labeled with panel number and circuit number from which it is fed. For receptacles rated higher than a NEMA 5-20R configuration, provide receptacles labeled additionally with voltage, phase, and amperage.
			18.	Pigtails: Provide 12 inch (305 mm) pigtails at feed locations.
			19.	Grounding: Factory installed NEC sized grounding conductor(s).
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
			20.	Covers: Hole-cut for communications devices.
			21.	Covers: Factory-mounted for voice and data/LAN outlets.
			22.	Fittings: Provide full compliment of fittings necessary to make system workable, including but not limited to external corner units, internal corner units, flat units, blank end units, elbows, and couplings for joining raceway sections.
	** NOTE TO SPECIFIER ** Edit the following paragraph if project requirements differ.
			23.	Wire Clips: One for every 2 linear feet (609 mm) of indicated raceway configuration.
			24.	Retrofit Corner Elbows, Tee Fittings and Inserts: Provide full line of full capacity corner elbows and tee fittings and inserts for retrofit, to maintain controlled 2 inch (51 mm) cable bend radius that meets TIA/EIA 569-A requirements for communications pathways and specifications for fiber optic and Category 5 cabling.
			25.	Fittings Material: Same material and metal thickness as linear raceway components.
			26.	Fittings Finish: To match linear raceway components.
			27.	Device Brackets and Plates: Factory-formed, allowing installation of indicated power, data, and communications devices, both single-gang and two-gang, horizontally in raceways; finished to match linear raceway components.
			28.	Cover Brackets and Face Plates: Plastic device mounting brackets and trim plates allowing installation of indicated power, data, and communications devices horizontally in raceways; trim cover sized to overlap device cut-out in raceway, concealing seams; finished to match linear raceway components; plastic compatible with UL 94.
			29.	Communications Devices and Accessories: Factory-fabricated connectivity outlets, modular inserts, and other devices for indicated configurations and service requirements.
	** NOTE TO SPECIFIER ** Delete the following paragraphs if not required.
				a.	Cabling Type: ____________.
				b.	Cabling Type: UTP, including Category 5.
				c.	Cabling Type: STP; 150-ohm.
				d.	Cabling Type: Fiber Optics.
				e.	Cabling Type: Coaxial.
				f.	Mounting face plates and bezels.
				g.	Identification Accessory: Printed station and port identification labels.
				h.	Identification Accessory: Snap-in icon buttons.
				i.	Identification Accessory: Write-on station identification labels.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
			30.	Electrical Devices: Factory-installed for indicated configurations and service requirements; sight-exposed components finished to match linear raceway components.
			31.	Electrical Devices: Electrical devices, and wiring for electrical devices, are specified in sections of Division 16.
			32.	Fasteners: Types specified in manufacturer's installation instructions for project conditions.
	** NOTE TO SPECIFIER ** Delete if not required.
	2.3	SURFACE NON-METALLIC RACEWAYS
		A.	General:
			1.	System: Provide surface raceway systems for branch circuit and data network voice, video and other low-voltage wiring. Surface raceway system shall consist of raceway bases, covers, appropriate fittings and device mounting plates necessary for a complete installation.
			2.	Configuration: Raceways shall be one- or two-piece design with base and snap-on cover, or three-piece design with base and two snap-on covers which snap side by side on a common base. Base shall be dividable with a fixed barrier for up to 4 compartments. Raceway shall be available in widths of 3/4 inch to 10 inches (19 mm to 254 mm) and depths of 17/32 inch to 5 inches (13.5 mm to 127 mm). Provide raceways from a company which can provide custom sizes if required. Raceway covers shall be available in tamper-resistant form with screws on access plates and covers of fittings, but not on standard cover lengths.
			3.	Fittings: Fittings shall include flat, internal and external elbows, couplings for joining raceway sections, wire clips, blank end fittings, and device mounting brackets and plates as applicable. Where required, provide tamper-resistant form, dividable with barriers and matching the size of the accompanying raceway base. Provide full capacity corner elbows and tee fittings to maintain a controlled 2 inch cable bend radius, meeting the specification for Fiber Optic and UTP cabling and exceeding the TIA/EIA-569-A requirements for communications pathways.
			4.	Device Brackets and Plates: Provide in sizes to match the raceway width and with mounting holes located to ensure proper mounting of devices in up to 4 compartments. Device plates shall be available in any length from 6 inch to 60 inch, with cutouts to accommodate various combinations of power and communications devices in up to 4 compartments. Provide 6 inch and 12 inch long device plates with a flange to overlap the joint of adjacent cover as applicable.
			5.	Communications Devices and Accessories: Raceway shall accommodate a complete line of connectivity outlets and modular inserts for UTP (including Category 5, 5e, 6) STP (150 ohm) fiber optic, coaxial, and other cabling types with matching faceplates and bezels to facilitate mounting. Where indicated, provide connectivity outlets and modular inserts by Ortronics or approved equal.
		B.	Classification:
			1.	Raceway and system components shall be UL and CUL listed.
			2.	Surface raceways shall be suitable for use in dry interior locations only, as covered in Article 386 (Surface Metal Raceways) 388 (Surface Nonmetallic Raceways) of the National Electrical Code.
			3.	Surface metal raceways and fittings shall be listed by Underwriters Laboratories under File Number E4376, Listing and Classification Number RJBT and File Number E41751, Listing and Classification Number RJPR respectively.
			4.	Systems shall comply with UL Standard UL5 for Surface Metal Raceways.
			5.	Larger 2 and 3 channel non-metallic raceways shall be UL Listed under File Nos. E90378 Guide RJTX and E90377 Guide RJYT, respectively.
		C.	Surface Non-Metallic Large Raceways: System of rigid polyvinyl chloride (PVC) extrusions, 8 feet (2438 mm) in length with nominal 0.09 inch (2.3 mm) wall thickness.
	** NOTE TO SPECIFIER ** Delete the following acceptable product paragraphs not required by project. If more than one is specified, indicate where each is to be used.
			1.	Acceptable Product: Wiremold Access 5000 Series Dual-Channel Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: Two channel base with integral divider; channel top has integral ribs to receive mounting device brackets; extruded snap-on cover; extruded cove snap-on trim cover finished to match; 5-3/4 inches (146 mm) wide by 13/16 inches (21 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory,
				c.	Finish: White
				d.	Finish: Gray.
				e.	Finish: Black.
				f.	Finish: Maple veneer
				g.	Finish: Oak veneer
				h.	Finish: Custom color as selected.
			2.	Acceptable Product: Wiremold 5400 Series Dual Channel Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: 5-1/4 inches (133 mm) wide by 1-3/4 inches (44 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
				c.	Base: Two channel, with integral divider (5400TB).
				d.	Base: Three channel, with two integral dividers, creating 1/2 and 1/4 compartments (5400TBD).
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
				e.	Cover: Full width snap-on cover.
				f.	Cover: Twin snap-on covers, one for each channel.
			3.	Acceptable Product: Wiremold 5500B Series Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: Base and snap-on cover; 6-11/16 inches (170 mm) wide by 1-11/16 inches (43 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
			4.	Acceptable Product: Wiremold 5500DB Series Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: Three channel base with integral dividers creating equal compartments; single snap-on cover; 6-11/16 inches (170 mm) wide by 1-11/16 inches (43 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
			5.	Acceptable Product: Wiremold CableSmart 40N2 Series Dual Channel Raceway by Wiremold/Legrand.
				a.	Construction: Two channel base with integral divider; snap-on cover spans entire base; 4 inches (102 mm) wide by 2 inches (51mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs. If more than one raceway is specified, indicate cover finishes for each.
			6.	Linear and Trim Cover Finish: _________.
			7.	Linear and Trim Cover Finish: As selected by Architect.
		D.	Surface Non-Metallic Small Raceways: Two piece system of rigid polyvinyl chloride (PVC) extrusions; 8 feet (2438 mm) in length with nominal 0.09 inch (2.3 mm) wall thickness.
	** NOTE TO SPECIFIER ** Delete the following acceptable product paragraphs not required by project. If more than one is specified, indicate where each is to be used.
			1.	Acceptable Product: Wiremold 400 Series Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: One channel base; snap cover wraps base top and sides; 7/8 inches (22 mm) wide by 7/16 inches (11 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
			2.	Acceptable Product: Wiremold 800 Series Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: One channel base; snap cover wraps base top and sides; 1-5/16 inches (33 mm) wide by 7/16 inches (11 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
			3.	Acceptable Product: Wiremold 2300 Series Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: One channel base; snap cover wraps base top and sides; 2-1/4 inches (57 mm) wide by 11/16 inches (18 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
			4.	Acceptable Product: Wiremold 2300D Series Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: Two channel base with integral divider; snap cover that wraps base top and sides; 2-1/4 inches (57 mm) wide by 11/16 inches (18 mm).
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs. If more than one raceway is specified, indicate cover finishes for each.
			5.	Linear and Trim Cover Finish: _________.
			6.	Linear and Trim Cover Finish: As selected by Architect.
		E.	Surface Non-Metallic Small Raceways: One piece system of rigid polyvinyl chloride (PVC) extrusions, base with co-extruded hinged cover and snap-close latch; 8 feet (2438 mm) in length with nominal 0.09 inch (2.3 mm) wall thickness.
	** NOTE TO SPECIFIER ** Delete the following acceptable product paragraphs not required by project. If more than one is specified, indicate where each is to be used.
	** NOTE TO SPECIFIER ** Uniduct 2700 is only for low voltage applications.
			1.	Acceptable Product: Wiremold Uniduct 2700 Series Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: 3/4 inches (19 mm) wide by 3/8 inches (10 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White, Fog White or custom color as selected.
	** NOTE TO SPECIFIER ** Uniduct 2800 is only for low voltage applications.
			2.	Acceptable Product: Wiremold Uniduct 2800 Series Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: 1 inch (25 mm) wide by 1/2 inch (13 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White, Fog White or custom color as selected.
	** NOTE TO SPECIFIER ** Uniduct 2900 is only for low voltage applications.
			3.	Acceptable Product: Wiremold Uniduct 2900 Series Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: 1-1/2 inches (38 mm) wide by 3/4 inches (19 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White, Fog White or custom color as selected.
			4.	Acceptable Product: Wiremold Eclipse PN03 Series Latching Surface Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: 13/16 inches (21 mm) wide by 1/2 inches (13 mm).
				b.	Finish: Manufacturer’s standard Ivory, White, Fog White or custom color as selected.
			5.	Acceptable Product: Wiremold Eclipse PN05 Series Latching Surface Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: 1-1/8 inches (29 mm) wide by 5/8 inches (16 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White, Fog White or custom color as selected.
			6.	Acceptable Product: Wiremold Eclipse PN10 Series Latching Surface Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: 1-11/16 inches (43 mm) wide by 13/16 inches (21 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White, Fog White or custom color as selected.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs. If more than one raceway is specified, indicate cover finishes for each.
			7.	Linear and Trim Cover Finish: _________.
			8.	Linear and Trim Cover Finish: As selected by Architect.
	** NOTE TO SPECIFIER ** Delete if not required by project.
		F.	Surface PreWired Non-Metallic Raceways: Wiremold Prewired series; factory designed and wired.
			1.	Acceptable Product: Wiremold 5500 Series Prewired Single and Multi-Channel Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: The system shall be manufactured of rigid PVC compound and have a textured finish, available in ivory and white colors. The raceway shall be a two-piece design with a base and snap-on cover. Total width shall be 6.68 inches by 1.75 inches (170 mm by 44 mm) deep with an approximate thickness of 0.10 inch (2.54 mm).
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
				c.	Base: Two channel, with integral divider (5500B).
				d.	Base: Three channel, with two integral divided compartments (5500BD).
			2.	Acceptable Product: Wiremold 5400 Series Prewired Dual Channel Nonmetallic Raceway by Wiremold/Legrand.
				a.	Construction: 5-1/4 inches (133 mm) wide by 1-3/4 inches (44 mm) deep.
				b.	Finish: Manufacturer’s standard Ivory, White or custom color as selected.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
				c.	Base: Two channel, with integral divider (5400TB).
				d.	Base: Three channel, with two integral dividers, creating 1/2 and 1/4 compartments (5400TBD).
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
				e.	Cover: Full width snap-on cover.
				f.	Cover: Twin snap-on covers, one for each channel.
			3.	Devices: Factory installed wiring and connectors.
			4.	Labels: Provide receptacles labeled with panel number and circuit number from which it is fed. For receptacles rated higher than a NEMA 5-20R configuration, provide receptacles labeled additionally with voltage, phase, and amperage.
			5.	Pigtails: Provide 12 inch (305 mm) pigtails at feed locations.
			6.	Grounding: Factory installed NEC sized grounding conductor(s).
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
			7.	Covers: Hole-cut for communications devices.
			8.	Covers: Factory-mounted for voice and data/LAN outlets.
	** NOTE TO SPECIFIER ** Delete any of the following paragraphs not required by project.
			9.	Fittings: Provide full compliment of fittings necessary to make system workable, including but not limited to external corner units, internal corner units, flat units, blank end units, elbows, and couplings for joining raceway sections.
	** NOTE TO SPECIFIER ** Edit the following paragraph if project requirements differ.
			10.	Wire Clips: One for every 2 linear feet (609 mm) of indicated raceway configuration.
			11.	Retrofit Corner Elbows, Tee Fittings and Inserts: Provide full line of full capacity corner elbows and tee fittings and inserts for retrofit, to maintain controlled 2 inch (51 mm) cable bend radius that meets TIA/EIA 569-A requirements for communications pathways and specifications for fiber optic and Category 5 cabling.
			12.	Replacement Divider Fittings: Provide two sections of replacement divider fitting for every 8 linear feet (2438 mm) of indicated base configuration.
			13.	Fittings Material: Same material and metal thickness as linear raceway components.
			14.	Fittings Finish: To match linear raceway components.
			15.	Device Brackets and Plates: Factory-formed, allowing installation of indicated power, data, and communications devices, both single-gang and two-gang, horizontally in raceways; finished to match linear raceway components.
			16.	Cover Brackets and Face Plates: Plastic device mounting brackets and trim plates allowing installation of indicated power, data, and communications devices horizontally in raceways; trim cover sized to overlap device cut-out in raceway, concealing seams; finished to match linear raceway components; plastic compatible with UL 94.
			17.	Communications Devices and Accessories: Factory-fabricated connectivity outlets, modular inserts, and other devices for indicated configurations and service requirements.
	** NOTE TO SPECIFIER ** Delete the following paragraphs if not required.
				a.	Cabling Type: ____________.
				b.	Cabling Type: UTP, including Category 5.
				c.	Cabling Type: STP; 150-ohm.
				d.	Cabling Type: Fiber Optics.
				e.	Cabling Type: Coaxial.
				f.	Mounting face plates and bezels.
				g.	Identification Accessory: Printed station and port identification labels.
				h.	Identification Accessory: Snap-in icon buttons.
				i.	Identification Accessory: Write-on station identification labels.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
			18.	Electrical Devices: Factory-installed for indicated configurations and service requirements; sight-exposed components finished to match linear raceway components.
			19.	Electrical devices, and wiring for electrical devices, are specified in sections of Division 16.
			20.	Fasteners: Types specified in manufacturer's installation instructions for project conditions.
	** NOTE TO SPECIFIER ** Delete if not required.
	2.4	INDOOR SERVICE POLES
		A.	Product: Wiremold Tele-Power Pole System; Two separate compartments.
		B.	General: Provide indoor service pole system to extend branch circuit wiring and data network, voice, video, and other communication cabling to points of use shown on the Drawings. System shall consist of pole multi-outlet assemblies, and appropriate fittings and accessories as required for a complete assembly.
		C.	Classification and Use: Indoor service pole system shall be suitable for use in dry interior locations, only as covered in Articles 353 and 352 Part A of the National Electrical Code, as adopted by the National Fire Protection Association and as approved by the American National Standards Institute.
		D.	The indoor service pole system is UL Listed under File Nos. E15191 Guide PVGT, E53857 Guide PVUR, E41751 Guide RJPR, and E169069 Guide ZTFR; also CUL Listed in the above files, or are CSA Certified in File LR350.
	** NOTE TO SPECIFIER ** Delete series if not required.
		E.	Series: 25DTP-4 Series and AMDTP-4 Series.
	** NOTE TO SPECIFIER ** Delete color not required.
			1.	Color: Steel.
			2.	Color: Ivory baked enamel.
			3.	Color: Clear anodized aluminum.
	** NOTE TO SPECIFIER ** Delete three of the following four paragraphs.
			4.	Length: 10 feet 5 inches (3175 mm).
			5.	Length: 12 feet 5 inches (3785 mm).
			6.	Length: 15 feet 5 inches (4699 mm).
			7.	Cross Section: 2.25 inches by 2.3125 inches (57mm by 59mm).
			8.	First compartment: factory wired with two duplex styles 20A, 125V. NEMA 5-20R grounding-type specification grade receptacles and colored to match the pole finish. Receptacles shall be UL tested to meet the performance requirements of Fed. Spec. W-C695G General Specification for Electrical Power Connectors and conform to NEMA Specification WD 1-7.01 to 7.10 "Heavy Duty General Use Grounding Receptacles". Receptacles shall also be UL Listed and be in compliance with UL-498.
			9.	Harness: single circuit (2 conductor plus ground) with #12 AWG solid type THHN conductors, factory assembled to the receptacles. 6 inches (152 mm) conductor leads are to be furnished for termination to the overhead wiring system. An 8 inches (203 mm) removable cover section shall be provided at the top of the power compartment to facilitate the hard wiring of the pole wire harness.
			10.	Second compartment: to be for field installation of telephone or data network cabling. An 8 inches (203 mm) removable cover section at the bottom of this compartment shall be provided to assemble and mount communications connectors. This section shall be removable without dismantling or removing the Tele-Power Pole after installation. The cover section is to have six knockouts for modular voice-data jacks (RJ-type) and a 1.375 inches by 2.7 inches (35 mm by 69 mm) rectangular knockout for a modular furniture outlet. A "mouse hole" knockout with furnished grommet is to be included for straight through communication cable access.
			11.	Fittings: Provide full compliment of fittings necessary to make system workable, including but not limited to entrance end fittings for top of each electrical channel, ceiling trim plate, pole-mounting bracket, Velcro(tm) carpet gripper pad, and adhesive pad. (If for air handling spaces, an entrance end fitting shall be furnished for the communications channel.)
			12.	Field install power device covers to add duplex, single 1.40 inch (36 mm) and 1.59 inch (40 mm), and rectangular-type receptacles, colored to match appropriate Tele-Power Pole.
			13.	Add-on communication covers shall be available to mount workstation device faceplates, inserts, and specialty mounting bezels. The power pole manufacturer will provide a complete line of connectivity outlets with multi-media modular inserts for UTP fiber optic, coaxial, and other cabling types.
			14.	UTP inserts shall feature a unique recessed area for port labeling and shall be able to accommodate designation icon buttons or icon labels. Custom label capabilities shall be available using templates that can be downloaded from the Internet.
			15.	Fiber Optic/Category 5 Cable Radius: There shall be a 2 inches (51mm) controlled radius entrance fitting, which meets or exceeds the specifications for fiber optic and Category 5 cabling and TIA/EIA-569A requirements for communications pathways, for the 25DT and AMDT Series Tele-Power Poles.
			16.	Modular Communications Insert Tele-Power Poles: The manufacturer shall provide a Tele-Power Pole with one compartment, factory wired with two duplex styles 20A, 125V NEMA 5-20R grounding-type specification grade receptacles, and colored to match the pole finish. Receptacles shall be UL tested to meet the performance requirements of Fed. Spec. W-C695G General Specification for Electrical Power Connectors and conform to NEMA Specification WD 1-7.01 to 7.10 "Heavy Duty General Use Grounding Receptacles". Receptacles shall also be UL Listed and be in compliance with UL-498. The harness is to be single circuit (2 conductor plus ground) with #12 AWG solid type THHN conductors, factory assembled to the receptacles. 6 inches (153) conductor leads are to be furnished for termination to the overhead wiring system. The other compartment shall have a modular communications insert bezel installed and three modular communications inserts, as well as labeling.
	** NOTE TO SPECIFIER ** Delete series if not required.
		F.	25DTP-4D Series and AMDTP-4D Dedicated / Isolated Ground Series
			1.	Color
	** NOTE TO SPECIFIER ** Delete color not required.
				a.	Steel
				b.	Ivory baked enamel
				c.	Clear Anodized Aluminum
			2.	Length:
	** NOTE TO SPECIFIER ** Delete length not required.
				a.	10 feet 5 inches (3.18 m).
				b.	12 feet 5 inches (3.78 m).
				c.	15 feet 5 inches (4.70 m).
			3.	Cross section: 2.25 inches by 2.3125 inches (57 mm by 59 mm).
			4.	First compartment: factory wired with one duplex specification grade grounding type receptacle, for branch circuits and one dedicated circuit duplex isolated ground receptacle, both rated 20A, 125V NEMA 5-20R. Each receptacle shall be on a separate circuit (six wires total) with #12 AWG solid type THHN conductors, factory assembled to the receptacles. 6 inches (152mm) conductor leads are to be furnished for termination to the overhead wiring system. An 8 inches (203 mm) removable cover section shall be provided at the top of the power compartment to facilitate the hard wiring of the pole harness.
			5.	Second compartment: for field installation of telephone or data network cabling. An 8 inches (203mm) removable cover section at the bottom of this compartment shall be provided to assemble and mount communications connectors. This section shall be removable without dismantling or removing the Tele-Power Pole after installation. The cover section is to have six knockouts for modular voice-data jacks (RJ-type) and a 1.375 inches by 2.7 inches (35mm by 69mm) rectangular knockout for a modular furniture outlet. A "mouse hole" knockout with furnished grommet is to be included for straight through communication cable access. The Tele-Power Pole shall be 10 feet 5 inches (3.18m) long.
			6.	Fittings: A full compliment of fittings for the Tele-Power Pole shall be available including, but not limited to, entrance end fitting for top of the electrical channel, ceiling trim plate, pole-mounting bracket, Velcro carpet gripper pad and adhesive pad. (If for air handling spaces, an entrance end fitting shall be furnished for the communications channel.)
			7.	Add-On Device Covers and Compartments: The Tele-Power Poles shall be UL Listed for field modifications, changes and additions of receptacles, devices, and circuits. Field installed device covers shall be available to add duplex, single 1.40 inches (36mm) and 1.59 inches (40mm) dia., and rectangular-type receptacles. These plates shall be color matched to the appropriate Tele-Power Pole.
			8.	Add-on communication covers shall be available to mount workstation device faceplates, inserts, and specialty mounting bezels. The power pole manufacturer will provide a complete line of connectivity outlets with multi-media modular inserts for UTP, fiber optic, coaxial, and other cabling types.
			9.	UTP inserts shall feature a unique recessed area for port labeling and shall be able to accommodate designation icon buttons or icon labels. Custom label capabilities shall be available using templates that can be downloaded from the Internet.
			10.	Fiber Optic/Category 5 Cable Radius: There shall be a 2 inches (51mm) controlled radius entrance fitting, which meets or exceeds the specifications for fiber optic and Category 5 cabling and TIA/EIA-569A requirements for communications pathways, entrance fitting for the 25DT and AMDT Series Tele-Power Poles.
			11.	Add-On Device Covers: The Tele-Power Poles shall be UL Listed for field modifications, changes and additions of receptacles, devices and circuits. Field installed device plates shall be available to add duplex, single 1.40 inches (36mm) and 1.59 inches (40mm) dia., and rectangular-type receptacles. These plates shall be ivory in color to match the Tele-Power Pole.
			12.	Add-on communication covers shall be available to mount workstation device faceplates, inserts, and specialty mounting bezels. The power pole manufacturer will provide a complete line of connectivity outlets and multi-media modular inserts for UTP, fiber optic, coaxial, and other cabling types.
			13.	UTP inserts shall feature a unique recessed area for port labeling and shall be able to accommodate designation icon buttons or icon labels. Custom label capabilities shall be available using templates that can be downloaded from the Internet.
	** NOTE TO SPECIFIER ** Delete series if not required.
		G.	30 Series:
			1.	Color:
	** NOTE TO SPECIFIER ** Delete color not required.
				a.	Steel.
				b.	Ivory baked enamel.
			2.	Length:
	** NOTE TO SPECIFIER ** Delete length not required.
				a.	10 feet 5 inches (3.18m).
				b.	12 feet 5 inches (3.78m).
			3.	Cross section:
	** NOTE TO SPECIFIER ** Delete type if not required.
				a.	30TP-2V — 1.53 inches by 2.75 inches (39mm by 70mm).
				b.	30TP-4V — 3 inches by 2.75 inches (76mm by 70mm).
			4.	First compartment: factory wired with two duplex 20A, 125V NEMA 5-20R grounding type specification grade receptacles, and matched to the pole finish. Harness: single circuit (2 conductor plus ground) with #12 AWG solid type THHN conductors, factory assembled to the receptacles. 6 inches (152mm) conductor leads are to be furnished for termination to the overhead wiring system.
			5.	Second compartment: for field installation of telephone or data network cabling. A 12 inches (305mm) removable cover section in this compartment shall be provided to assemble and mount communications connectors. This section shall be removable without dismantling or removing the Tele-Power Pole after installation. The cover section is to have four knockouts for modular voice-data jacks (RJ-type) and a 1.375 inches by 2.7 inches (35mm by 69mm) rectangular knockout for a modular furniture outlet. A "mouse hole" knockout with furnished grommet is to be included for straight through communication cable access.
			6.	Fittings: A full compliment of fittings for the Tele-Power Pole shall be available including, but not limited to, entrance end fitting for top of the electrical channel, ceiling trim plate, pole-mounting bracket, Velcro carpet gripper pad, and adhesive pad. (If for air handling spaces, an entrance end fitting shall be furnished for the communications channel.)
			7.	Add-On Device Covers: The Tele-Power Poles shall be UL Listed for field modifications, changes and additions of receptacles, devices and circuits. Field installed device plates shall be available to add duplex, single 1.40 inches (36mm) and 1.59 inches (40mm) dia., and rectangular-type receptacles. These plates shall be ivory in color to match the Tele-Power Pole.
			8.	Add-on communication covers shall be available to mount workstation device faceplates, inserts, and specialty mounting bezels. The power pole manufacturer will provide a complete line of connectivity outlets and multi-media modular inserts for UTP, fiber optic, coaxial, and other cabling types.
			9.	UTP inserts shall feature a unique recessed area for port labeling and shall be able to accommodate designation icon buttons or icon labels. Custom label capabilities shall be available using templates that can be downloaded from the Internet.
			10.	Modular Communications Inserts Tele-Power Poles: The manufacturer shall provide a Tele-Power Pole with one compartment, factory wired with two duplex styles 20A, 125V NEMA 5-20R grounding-type specification grade receptacles, and colored to match the pole finish. Receptacles shall be UL tested to meet the performance requirements of Fed. Spec. W-C695G General Specification for Electrical Power Connectors and conform to NEMA Specification WD 1-7.01 to 7.10 "Heavy Duty General Use Grounding Receptacles". Receptacles shall also be UL Listed and be in compliance with UL-498. The harness is to be single circuit (2 conductor plus ground) with #12 AWG solid type THHN conductors, factory assembled to the receptacles. 6 inches (152mm) conductor leads are to be furnished for termination to the overhead wiring system. The other compartment shall have a modular communications insert bezel installed and three modular communications inserts, as well as labeling.
	** NOTE TO SPECIFIER ** Delete series if not required.
		H.	Round ALTP Series
			1.	The Tele-Power Pole channel shall be a 2 inches (51mm) diameter round aluminum extrusion.
			2.	Color
	** NOTE TO SPECIFIER ** Delete color not required.
				a.	ALTP-20W painted office white.
				b.	ALTP-2P polished aluminum anodized.
				c.	ALTP-2S satin anodized.
			3.	The Tele-Power Pole shall be 10 feet 4 inches (3.17m) long.
			4.	First compartment is to be factory wired with four single 15A, 125V NEMA 5-15R grounding type specification grade receptacles.
			5.	Harness is to be single circuit (2 conductor plus ground) with #12 AWG solid type THHN conductors, factory assembled to the receptacles. 6 inches (152mm) conductor leads are to be furnished for termination to the overhead wiring system.
			6.	Second compartment is to be for field installation of telephone or data network cabling. A 1/2 inch (12.7mm) trade size knockout and grommet is to be provided at the base of the pole for straight through communication cable access.
			7.	Fittings: A full compliment of fittings for the Tele-Power Pole shall be available including, but not limited to, entrance end fitting for top of the electrical channel, ceiling trim plate, pole mounting bracket and foot assembly for carpet and hard surfaces.
	** NOTE TO SPECIFIER ** Delete series if not required.
		I.	NP600 Series
			1.	Color
	** NOTE TO SPECIFIER ** Delete color not required.
				a.	Anodized
				b.	Powder coated custom color (specify:_________)
			2.	Length: All poles may be provided between 8 feet (2.4m) and 30 feet (9.14m) in length. (specify: ________)
			3.	Cross section of 2.125 inches by 2.375 inches (54mm by 60mm)
			4.	Compartments: two separate compartments. Poles may be wired in either or both channels with wires suitable for 15, 20, or 30 amp circuits. Any channel may be wired with up to 12 duplex receptacles, with the number of circuits limited by the size of the utility box on the pole in accordance with this manufacturer's approvals. Receptacles shall be UL Listed or CSA Certified as applicable, and may be of any specified grade or style, and in standard, isolated ground, or surge form. The poles may also be used in conjunction with the Walkerflex Manufactured Wiring System. cUL Listed poles may be provided with up to two cord-ends per channel, with all components Canadian Certified. Cords are to be a maximum of 10 feet (3m) long.
			5.	Compartments intended for power wiring shall have the ends closed off by an outlet box, end plate, or foot. Power and communication or low voltage wiring shall be in separate channels. Receptacles shall be connected to an unbroken ground wire, which is either connected to the pole body or extends into the outlet box.
			6.	Wiring:
	** NOTE TO SPECIFIER ** Delete option not required.
				a.	Pole provided with wiring
				b.	Pole provided without wiring for subsequent routing of cables and conduit, according to this manufacturer's approvals.
			7.	Fittings: A full compliment of fittings for the Tele-Power Pole shall be available including, but not limited to, utility box for the top of a power channel, end blanks, adjustable and non-adjustable feet c/w carpet gripper pad and adhesive pad, ceiling trim plate, pole mounting bracket, and pole adapter.
			8.	Add-On Compartments: The Tele-Power Poles may be provided with up to two add-on compartments to provide additional channels. Poles may also be furnished fastened together through the sides to form a four channel side-by-side pole. The capacity of the add-on compartment is the same as one channel of the NP600.
			9.	Communication Devices and Accessories: The manufacturer will provide a complete line of connectivity outlets with modular multi-media inserts for voice, data, video, audio, etc. with faceplates and bezels to facilitate mounting. A complete line of preprinted station and port identification labels, snap-in icon buttons and write-on station identification labels shall be available.
			10.	UTP inserts shall feature a unique recessed area for port labeling and shall be able to accommodate designation icon buttons or icon labels. Custom label capabilities shall be available using templates that can be downloaded from the Internet.
	** NOTE TO SPECIFIER ** Delete series if not required.
		J.	NP800 Series
			1.	Color
	** NOTE TO SPECIFIER ** Delete color if not required.
				a.	Anodized.
				b.	Powder coated custom color (specify:_________).
			2.	Length: All poles may be provided between 8 feet (2.4m) and 30 feet (9.14m) in length. (specify: ________).
			3.	Cross section of 5 inches by 4.625 inches (127mm by 120mm).
			4.	Compartments: two separate compartments. Poles may be activated in either or both channels and wired with a maximum conductor size of #6 AWG. Any channel may be wired with up to 12 duplex receptacles, with the number of circuits limited by the size and number of utility boxes on the pole in accordance with this manufacturer's approvals. Receptacles shall be UL Listed or CSA Certified as applicable, and may be of any specified grade or style, and in standard, isolated ground, or surge form. The poles may also be used in conjunction with the Walkerflex Manufactured Wiring System. cUL Listed poles may be provided with up to three cord-ends per channel, with all components Canadian Certified. Cords are to be a maximum of 10 feet (3m) long.
			5.	Channels intended for power wiring shall have the ends closed off by an outlet box, end plate, or foot. Power and communication or low voltage wiring shall be in separate channels. Receptacles shall be connected to an unbroken ground wire, which is either connected to the pole body or extends into the outlet box.
			6.	The NP800 Base shall have four integral ribs on either side of the divider to accept snap-in divider sections. Snap-in dividers shall be extruded 0.050 inches (1.27mm) aluminum of the same length as the Tele-Power Pole. When snap-in dividers are utilized, each new compartment constitutes a new channel.
			7.	Wiring:
	** NOTE TO SPECIFIER ** Delete option not required.
				a.	Pole provided with wiring.
				b.	Pole provided without wiring for subsequent routing of cables and conduit, according to this manufacturer's approvals.
			8.	Fittings: A full compliment of fittings for the Tele-Power Pole shall be available including, but not limited to, utility box for the top of a power channel, end blanks, adjustable and non-adjustable feet c/w carpet gripper pad and adhesive pad, ceiling trim plate, pole mounting bracket, and pole adapter.
			9.	Communication Devices and Accessories: The manufacturer will provide a complete line of connectivity outlets and modular multi-media inserts for voice, data, video, audio, etc. with faceplates and bezels to facilitate mounting. A complete line of preprinted station and port identification labels, snap-in icon buttons, and write-on station identification labels shall be available.
			10.	UTP inserts shall feature a unique recessed area for port labeling and shall be able to accommodate designation icon buttons or icon labels. Custom label capabilities shall be available using templates that can be downloaded from the Internet.
	** NOTE TO SPECIFIER ** Delete series if not required.
	2.5	ARCHITECTURAL SERVICE COLUMNS
		A.	Vista Service Column as manufactured by Wiremold/Legrand.
		B.	Classification and Use: Architectural columns shall be suitable for use in dry interior locations only as covered in Article 380 of the National Electrical Code (NEC) and shall be UL Listed under File No. E15191, and be listed by Canadian Underwriters (cUL).
		C.	General: Architectural columns consisting of vertical chase and multi-outlet systems to provide a wire path and access point for communications and power. Systems shall consist of modular vertical channels and appropriate fittings as required for a complete assembly. Systems shall include a pre-punched support and aluminum end covers.
		D.	Frame: Four-piece design with two center supports with snap-on covers and end caps, providing a total of three useable wire and cable channels. Mill finished 6063-T6 aluminum with satin anodized aluminum end caps. Covers and access panels may be painted over and are suitable for field painting. The aluminum extrusions will be a minimum thickness of 0.06 inch (1.5mm), and steel covers .040 inch (1.0 mm). The system shall be available in 10 feet 6 inches (3.2 m) height. The system shall be available with an extension kit that includes aluminum tubes to allow for varying ceiling heights up to 15 feet (4.5 m). Access panels and covers up to a height of 30 inches (762 mm) above finished floor will provide access to wiring and devices. The frame supports shall be available with factory pre-punched hole cuts for communication receptacles and trade knockouts for electrical terminations.
			1.	End Caps:
	** NOTE TO SPECIFIER ** Delete design not required.
				a.	Design: Round.
				b.	Design: Square.
			2.	Material:
	** NOTE TO SPECIFIER ** Delete materialnot required.
				a.	Snap-on steel.
				b.	Snap on aluminum.
			3.	Center Panels:
	** NOTE TO SPECIFIER ** Delete finish not required.
				a.	Painted steel
				b.	Aluminum
				c.	Stainless steel
			4.	Heights:
	** NOTE TO SPECIFIER ** Delete height not required.
				a.	96 inches (2438 mm)
				b.	30 inches (762 mm)
				c.	24 inches (610 mm),
				d.	6 inches (152 mm)
	** NOTE TO SPECIFIER ** Delete adornment not required.
			5.	Adornment: Wood laminate.
			6.	Adornment: Nonmetallic laminate.
			7.	Adornment: Fabric.
			8.	Adornment: Painted.
			9.	Fittings: Provide internal braces with knockouts, snap-in dividers and wire clips and ceiling and carpet trim pieces as scheduled or required.
			10.	Multi-Outlet Wiring Harness: Consisting of 20 Amp 125 Volt NEMA 5-20R specification grade receptacles. The harnesses shall be available in single circuit (2 conductor plus ground) and alternating two circuit (3 conductor plus ground) wiring configuration as scheduled or required. Wiring shall be #12 AWG solid type THHN conductors, factory assembled to the receptacles.
	** NOTE TO SPECIFIER ** Delete if furniture feeds are not required.
			11.	Furniture Feed: Provide a plate with openings and knockouts providing the openings necessary for the architectural column to feed a modular furniture system.
	** NOTE TO SPECIFIER ** Delete series if not required.
		E.	Vista Consolidation Point as manufactured by Wiremold/Legrand.
			1.	One side shall be a metallic center panel, finished with laminate products or fabric. The other side shall be a lockable door to enclose the consolidation point.
				a.	Communication Devices and Accessories: Provide Ortronics 110 to Mini or Pass & Seymour 110 to Mini patch panels.
				b.	Size: 13.4 inches wide by 3.8 inches deep (340 mm by 96.5 mm).
				c.	System Height: 10 feet 6 inches (3200 mm).
				d.	Door: Provide a 60-inches (1524 mm) high door constructed of painted or anodized aluminum on the front side of the column. Equip door with handle as selected from manufacturer's currently available range.
	** NOTE TO SPECIFIER ** Delete keyed lock if not required.
				e.	Provide keyed lock.
	** NOTE TO SPECIFIER ** Delete series if not required.
		F.	Vista Architectural Column as manufactured by Wiremold/Legrand. Provide furniture feed or wired receptacle harnesses and appropriate fittings.
			1.	Sizes:
	** NOTE TO SPECIFIER ** Delete sizes not required.
				a.	8.9 inches wide by 3.8 inches deep (226 mm by 96.5 mm).
				b.	13.4 inches wide by 3.8 inches deep (340 mm by 96.5 mm).
			2.	System Height: 10 feet 6 inches (3200 mm).
			3.	Communication Devices and Accessories: Provide connectivity outlets and modular inserts for UTP, STP (150 ohm) Fiber Optic, Coaxial and other cabling types with faceplates and bezels to facilitate mounting.
	** NOTE TO SPECIFIER ** Delete if not required.
			4.	Lighting Bracket: Provide a bracket to attach commercially available light fixtures weighing no more than 10 lb (25 kg) to the column.
	** NOTE TO SPECIFIER ** Delete series if not required.
	2.6	MULTI-SERVICE IN-WALL BOX
		A.	Multi-Service In-Wall Boxes: Provide construction box system for bringing power and low voltage devices to one location or to back feed surface wiring systems. System shall consist of in-the-wall boxes, mounting brackets, dividers, device mounting brackets, trim rings, and device plates for a complete installation in accordance with the Drawings and schedules.
		B.	Classification and Use: Provide construction box system to be utilized in dry, interior locations only as defined by Article 300-15 of the National Electrical Code, as adopted by the National Fire Protection Association and approved by the American National Standards Institute. The box and system components shall be UL listed in accordance with UL 514A and UL514C. The device mounting bracket shall be molded from color matching UL approved resin.
		C.	Product: Wiremold WallSource Multi Service Box by Wiremold/Legrand.
	** NOTE TO SPECIFIER ** Delete material not required.
			1.	Material: 0.050 inch (1.27 mm) thick galvanized steel with gray or ivory suitable for field painting.
			2.	Material: 0.063 inches (1.52 mm) thick extruded aluminum with clear anodized finish.
		D.	Boxes: Each box shall include the box, dividers and mounting brackets. Dimensions of each shall be a minimum of 32 cubic inches per gang. The box shall accommodate standard power and communication devices.
			1.	The 2-gang box shall have knockouts located on top and bottom, 2-1/4 inches (57 mm) from the face to accommodate combinations of 1/2 inch, 3/4 inch, and 1 inch (13 mm, 19 mm and 25 mm) trade size conduits. Boxes of 4- or 6-gangs shall have knockouts to accommodate 1-1/2 inches (38 mm) trade size conduits.
			2.	Box shall have a separate ground terminal provided in each gang.
			3.	Box shall adjust for a flush installation with the finished wall. There shall be positive stops for surface mounting to 1/2 inch, 5/8 inch, 1 inch and 1-1/4 inches (13 mm, 16 mm, 25 mm and 32 mm) thick wallboard. Adjusting screws shall be located outside the box for adjustment prior to installation.
		E.	Device Mounting Brackets: Self-leveling device mounting bracket shall accommodate standard power devices, connectivity inserts, and Wiremold 5507 series faceplates. Mounting bracket shall be available to accommodate other manufacturer's devices. Mounting bracket shall accommodate six power devices or 18 communications inserts. All faceplates, mounting brackets and trim rings shall be color matched.
		F.	Communication Devices and Accessories: Box shall accommodate a complete line of connectivity outlets and modular inserts for UTP (including Category 5, 5e, 6) STP (150 ohm) fiber optic, coaxial, and other cabling types with matching faceplates and bezels to facilitate mounting. Where indicated, provide connectivity outlets and modular inserts by Ortronics or approved equal.
		G.	Fiber Optic/UTP (including Category 5, 5e, 6) Radius: The depth of the box shall accommodate a 1-1/4 inches (32 mm) cable bend radius, which meets or exceeds the specifications for fiber optic and UTP cabling and TIA/EIA-569A requirements for communications pathways. A 1 inch (25 mm) controlled radius storage loop shall be available.
		H.	Device Covers: Device cover plates in the following configurations shall be available: duplex device cover plates, single 1.40 inch (36 mm) and 1.59 inches (40 mm) diameter receptacle cover plates, switch plates, GFCI cover plates, Sentrex surge receptacle cover plates and other rectangular faced plates. Single gang cover plates shall be modular in design.
		I.	Support Bracket: Provide support bracket for mounting on 16 inches (406 mm) on center studs on boxes with more than two gangs.
		J.	Dividers: Dividers shall be removable without any tools.
	** NOTE TO SPECIFIER ** Delete if not required.
	2.7	FLOOR BOXES FOR ON-GRADE AND ABOVE-GRADE CONCRETE FLOORS
		A.	Classification and Use: Provide floor boxes approved for use in concrete floor construction. Boxes shall be approved for above grade (stamped steel) and on grade (epoxy coated stamped steel (spec locker), cast iron or nonmetallic) applications. Floor boxes shall have been examined and tested by Underwriters Laboratories Inc. to meet UL514A and Canadian Standard C22.2 and shall bear the appropriate label. Floor boxes shall conform to the standard set in the National Electrical Code. Multi-compartment box shall have been evaluated by UL to meet the applicable U.S. and Canadian safety standards for scrub water exclusion when used on tile, terrazzo, wood, and carpet covered floors.
		B.	Configurations: Boxes shall be available in one-, two-, or three-gang configurations or a single unit with two to eleven independent wiring compartments and available in stamped steel, epoxy coated stamped steel, nonmetallic and cast iron versions. Boxes shall be available in deep and shallow versions. Boxes shall provide pre- and post-pour adjustments. Multiple gang boxes shall also provide a removable barrier between the individual compartments for greater capacity when required. Refer to Drawings for size and types.
			1.	Product: Resource RFB Series Floor Boxes for Concrete Floors by Wiremold/Legrand.
			2.	Product: Resource RFB4-SS Series Shallow Stamped Steel Floor Boxes for Concrete Floors by Wiremold/Legrand.
			3.	Product: 880 Omnibox Series Floor Boxes for Concrete Floors by Wiremold/Legrand.
			4.	Product: 880 Series Round Floor Boxes by Wiremold/Legrand.
			5.	Product: 800 Series Round Floor Boxes by Wiremold/Legrand.
			6.	Product: 880MP Series Nonmetallic Rectangular Floor Boxes by Wiremold/Legrand.
			7.	Product: 881 Series Nonmetallic Round Floor Boxes for Concrete Floors by Wiremold/Legrand.
			8.	Product: 882C/884C Series Nonmetallic Round Floor Boxes for Concrete Floors by Wiremold/Legrand.
		C.	Metallic Floor Boxes:
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs. Cast-iron option is not available for wood floors.
			1.	Material: Stamped steel, formed; 1-3/4 inches (44 mm) pre-pour adjustment; 1/2 inch (13 mm) post-pour adjustment.
			2.	Material: Cast iron; box interior and exterior painted; 1-3/4 inches (44 mm) pre-pour adjustment; 1/2 inch (13 mm) post-pour adjustment.
			3.	Material: Epoxy coated cast iron; box interior and exterior painted; 1-3/4 inches (44 mm) pre-pour adjustment; 1/2 inch (13 mm) post-pour adjustment.
			4.	Box Type: Rectangular.
			5.	Box Type: Round.
			6.	Service: Single.
			7.	Service: Dual.
			8.	Service: Multiple.
	** NOTE TO SPECIFIER ** Delete items not required.
			9.	Gang Capacity: 1 gang.
			10.	Gang Capacity: 2 gangs.
			11.	Gang Capacity: 3 gangs.
			12.	Gang Capacity: 4 gangs.
			13.	Gang Capacity: 6 gangs.
			14.	Gang Capacity: 9 gangs.
			15.	Gang Capacity: 11 gangs.
	** NOTE TO SPECIFIER ** First item below is for RFB Series; second is for Omnibox Series. Delete items not required.
			16.	Cover Construction: Die-cast aluminum.
			17.	Cover Construction: Metal/polycarbonate.
			18.	Cover Construction: Brass.
	** NOTE TO SPECIFIER ** Delete items not required.
			19.	Cover Plates and Flanges: Black on steel.
			20.	Cover Plates and Flanges: Brown on steel.
			21.	Cover Plates and Flanges: Brushed brass.
			22.	Cover Plates and Flanges: Brushed aluminum.
			23.	Cover Plates and Flanges: Bronze.
			24.	Cover Plate and Flange Applications: To match floor box configuration.
			25.	Flanges shall accommodate connectivity outlets and modular inserts. Where indicated, provide connectivity outlets and modular inserts by Ortronics or approved equal.
			26.	Modular inserts shall snap directly into each flange through the use of a mounting bezel.
		D.	Nonmetallic Floor Boxes: Boxes shall be manufactured through the use of injection molded Geon M3900 PVC material. The box shall be round or rectangular in shape. Box shall allow for ganging of boxes together through the dovetail, interlocking mechanism. Knockouts shall be provided on the side walls of each box to provide for pass-through capability between each gang. Box shall also have concrete depth markings on the exterior of the box to indicate box depth at the time of the pour. Box shall also provide graduated cubic inch markings on the interior of the box to indicate volume capacity at the appropriate box depth.
			1.	Concrete Depth: 3-1/2 inches (89 mm) minimum; 6 inches (152 mm) maximum.
	** NOTE TO SPECIFIER ** Delete items not required.
			2.	Service: Single.
			3.	Service: Dual.
			4.	Service: Multiple.
			5.	Floor Box Shape:
				a.	Rectangular.
				b.	Round.
			6.	Knockouts:
				a.	Rectangular floor boxes shall provide two 1-1/4 inches (32 mm) openings, adjustable to accommodate 1/2 inch (13 mm), 3/4 inch (19 mm) and 1 inch (25 mm) trade size conduits.
				b.	Round floor boxes shall provide four 1 inch (25mm) conduit opening to feed cabling to the box. Box shall provide the means to reduce this opening to fit 3/4 inch (19 mm) and 1/2 inch (13 mm) conduit sizes.
			7.	Box shall be equipped with a high impact mudcap to protect the box from damage and prevent concrete entry during the pour and debris entry after the pour. Box shall also provide ratchet teeth-(spec locker) along interior box walls to attach cover. Box shall include internal spacer to prevent deformation of the box sidewalls when high temperature additives are used in the concrete pour.
			8.	Adjusting rings shall be used to attach flanges and covers to the floor box body. Adjusting ring shall have ratchet teeth to align with the teeth on box wall to connect box body without the use of adhesive or mechanical fasteners. Adjusting ring shall provide for 10 degrees of adjustment after concrete pour to adjust to various concrete conditions and floor finishes. Provide brass inserts to mount finish flanges to box body. Adjusting ring shall also provide for grounding locations using brass inserts.
			9.	Adjusting ring shall provide the ability to accept a modular connectivity system. Modular communication inserts shall snap directly into the adjusting ring openings. Adjusting ring for the rectangular box shall provide a fiber storage loop to maintain proper fiber optic bend radius control and excess fiber storage. Each adjusting ring shall except up to six connectivity activation locations. Adjusting ring shall allow modular connectivity inserts to be mounted recessed and protected when not in use.
			10.	Covers and Flanges: Flanges shall be available in one-, two-, and three-gang applications. Rectangular flanges for brass, brushed aluminum and nonmetallic cover plates shall be available in one-, two-, and three-gang applications. Round flanges for brass, brushed aluminum and nonmetallic covers plates shall be available in single and multiservice applications. Each flange shall provide 1/2 inch (13 mm) of adjustment to accommodate various floor coverings and concrete depths.
	** NOTE TO SPECIFIER ** Delete items not required.
			11.	Cover Plates and Flanges: Black on steel.
			12.	Cover Plates and Flanges: Brown on steel.
			13.	Cover Plates and Flanges: Brushed brass.
			14.	Cover Plates and Flanges: Brushed aluminum.
			15.	Cover Plates and Flanges: Bronze.
			16.	Flanges shall accommodate connectivity outlets and modular inserts.
			17.	Modular inserts shall snap directly into each flange using a mounting bezel.
		E.	Multi-Compartment Floor Boxes: Two to eleven independent wiring compartments allow up to eleven duplex receptacles/communications services; tunneling feature allows internal wiring to various compartments; fully adjustable box, providing maximum 1-7/8 inches (48 mm) pre-pour and maximum 3/4 inch (19 mm) post-pour adjustments.
	** NOTE TO SPECIFIER ** Cast iron not available in shallow depth. Delete depth not required.
			1.	Depth: Deep.
			2.	Depth: Shallow.
			3.	Boxes shall provide a series of device mounting plates that will accept duplex power devices, audio/visual devices as well as plates that will accommodate connectivity outlets and modular inserts. Where scheduled, provide connectivity outlets and modular inserts by Ortronics or approved equal.
			4.	Activation Covers shall be available with options for tile or carpet inserts, blank covers, or covers with concentric 1-1/4 inches (32 mm) and 2 inches (51 mm) trade size plug openings for furniture feed applications as scheduled.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
				a.	Activation Cover: Die-cast aluminum - Flanged.
				b.	Activation Cover: Die-cast aluminum - Flangeless.
	** NOTE TO SPECIFIER ** Delete two of the following three paragraphs.
				c.	Activation Cover Finish: Brushed aluminum.
				d.	Activation Cover Finish: Black powder-coated.
				e.	Activation Cover Finish: Brass plated finish.
	** NOTE TO SPECIFIER ** Delete if not required.
	2.8	FIRE CLASSIFIED FLOOR BOXES FOR ON-GRADE AND ABOVE-GRADE CONCRETE FLOORS
	** NOTE TO SPECIFIER ** Fire classified floor box use is limited by the UL Fire Resistance Directory to a minimum spacing of 2 feet (610mm) on center and not more than one device per 4 square feet (.372m2) of floor area in each span. Nonmetallic Fire Classified Floor Box use is limited by the UL Fire Resistance Directory to a minimum spacing of 2 feet (610 mm) on center and not more than one device per 65 square feet (6 square meters) of floor area in each span.
		A.	Classification and Use: Floor boxes shall have been examined and tested by Underwriters Laboratories Inc. to comply with UL514A and/or UL514C and Canadian Standard C22.2, No. 18-98 and bear the U.S. and Canadian UL Listing Mark. Fire classified floor boxes shall also have been tested by UL and classified for fire resistance and bear the U.S. and Canadian UL Classification Mark. The floor boxes shall conform to the standards set forth in the National Electrical Code, Section 300-21.
			1.	Fire Rated Floor boxes shall be classified for use in 1, 1-1/2, or 2-hour rated floors and 1, 1-1/2, or 2 hour rated floors employing unprotected steel floor units and, or concrete floors with suspended ceilings. Fire resistive designs with suspended ceilings shall have provisions for accessibility in the ceiling below the floor boxes.
			2.	Floor boxes shall have been evaluated by UL to meet the applicable U.S. and Canadian safety standards for scrub water exclusion when used on tile, terrazzo, wood, and carpet covered floors.
			3.	These devices are not suitable for wet or damp locations, or other areas subject to saturation with water or other liquids such as commercial kitchens.
			4.	Floor boxes shall be suitable for use in air handling spaces in accordance with Section 300-22C of the National Electrical Code.
		B.	Configurations:
			1.	Fire classified floor boxes provide an interface between power, communication and audio/visual (A/V) cabling in an above grade concrete floor and the workstation or activation location where power, communication and/or A/V device outlets are required. These devices provide flush and recessed outlets that will not obstruct the floor area. Refer to the Drawings for types.
			2.	Fire classified floor boxes shall be compatible with the complete line of Ortronics workstation connectivity outlets and modular inserts, or Pass & Seymour Network Wiring System.
	** NOTE TO SPECIFIER ** In the following paragraph, retain only those products that are to be incorporated into the project and delete the others.
		C.	Omnibox 880 Series Fire Classified Floor Boxes: Boxes shall be available in one-, two-, or three-gang configurations and available in a stamped-steel version. Boxes shall also be rectangular in shape and available in deep and shallow versions. All boxes shall also provide pre- and post-pour adjustment. All boxes shall also provide a removable barrier between the individual compartments for greater capacity when required.
	** NOTE TO SPECIFIER ** Delete model not required.
			1.	Model: 880M1FC Fire Classified Floor Boxes as manufactured by Wiremold/Legrand.
			2.	Model: 880M2FC Fire Classified Floor Boxes as manufactured by Wiremold/Legrand.
			3.	Model: 880M3FC Fire Classified Floor Boxes as manufactured by Wiremold/Legrand.
			4.	Model: 880S1FC Fire Classified Floor Boxes as manufactured by Wiremold/Legrand.
			5.	Model: 880S2FC Fire Classified Floor Boxes as manufactured by Wiremold/Legrand.
			6.	Model: 880S3FC Fire Classified Floor Boxes as manufactured by Wiremold/Legrand.
	** NOTE TO SPECIFIER ** In the following paragraph, retain only those products that are to be incorporated into the project and delete the others.
			7.	Body: Boxes shall be manufactured from stamped steel and formed. Boxes shall be available in one-, two-, or three-gang configurations. Shallow stamped steel versions shall provide 3/4-inch (44mm) of pre-pour adjustment and 1/2-inch (12.7mm) of post-pour adjustment. Deep stamped steel versions shall provide 1/2-inch (12.7mm) of pre-pour adjustment and 1/2-inch (12.7mm) of post-pour adjustment. Minimum concrete depth of deep boxes shall be 4-1/2 inches (114mm). Minimum concrete depth of shallow boxes shall be 3-1/4 inches (83mm). Overall box dimensions for both shallow and deep boxes shall be as follows:
				a.	One-gang: 4-13/16 inches (122mm) W by 3-23/32 inches (94mm) L.
				b.	Two-gang: 4-13/16 inches (122mm) W by 7-15/16 inches (202mm) L.
				c.	Three-gang: 4-13/16 inches (122mm) W by 12 inches (305mm) L.
			8.	One-gang Boxes: Deep boxes shall provide at least 53 cu in (869ml) of device wiring chamber volume. Shallow boxes shall provide at least 37 cu in (607ml) of device wiring chamber volume.
				a.	The shallow and deep versions shall include one (1) intumescent stem with a 1-1/4-inch (31mm) diameter pass-through channel that allows the pathway to close off during a fire. The box shall provide an insulated assembly that will go on the underside of the floor structure to slow down the transfer of heat to the floor box.
			9.	Two-gang Boxes: Deep boxes shall provide at least a total of 117 cu in (1918ml) of device wiring chamber volume. This total volume shall be divided evenly between the two (2) gangs with 58.5 cu in (958ml) of volume in each gang. Shallow boxes shall provide at least a total of 80 cu in (1312ml) of device wiring chamber volume. This total volume shall be divided between the two (2) gangs with 40 cu in (656ml) of volume in each gang.
				a.	The shallow and deep versions shall include two (2) intumescent stems with a 1-1/4-inches (31mm) diameter pass-through channel that allows the pathway to close off during a fire. The box shall provide an insulated assembly that will go on the underside of the floor structure to slow down the transfer of heat to the floor box.
			10.	Three-gang Boxes: Deep boxes shall provide at least a total of 180 cu in (2951ml) of device wiring chamber volume. This total volume shall be divided among the three gangs with 54 cu in (885ml) of volume in each of the outside gangs and 67.5 cu in (1106ml) of volume in the center gang. Three-gang shallow boxes shall provide at least a total of 117 cu in (1917ml) of device wiring chamber volume. This total volume shall be divided among the three gangs with 36 cu in (590ml) of volume in each of the outside gangs and 45 cu in (737ml) of volume in the center gang.
				a.	The shallow and deep versions shall include three (3) intumescent stems with a 1-1/4-inches (31mm) diameter pass-through channel that allows the pathway to close off during a fire. The box shall provide an insulated assembly that will go on the underside of the floor structure to slow down the transfer of heat to the floor box.
	** NOTE TO SPECIFIER ** Select either the powder-coated or plated finish in the following subparagraph and delete the other finish.
			11.	Activation Cover: All floor box options shall accept brass and brushed aluminum cover plates and flanges. Flanges for brass and brushed aluminum shall be available for one-, two-, or three-gang applications and install on the previously mentioned boxes. Each flange shall provide 1/2 inch (12.7mm) of adjustment to accommodate various floor covering and concrete pour depths.
			12.	Communication covers shall accommodate Ortronics workstation connectivity outlets and modular inserts, and Wiremold Connectivity Modular Insert System.
			13.	Flanges: Brass, and brushed aluminum flanges shall be approved for use on carpet, tile, or wood covered floor applications. Brass and brushed aluminum flanges and cover plates shall have a buffed appearance and be protected with a lacquer finish. Brushed aluminum cover plate dimensions shall be 3.29 inches (83.566mm) W by 4.310 inches (109.474mm) L. Brushed aluminum cover plates shall seat inside only brushed aluminum and be flush with the finish floor. Brass cover plate dimensions shall be 3.156 inches (80.162mm) W by 4.182 inches (106.223mm) L. Brass cover plates shall seat inside only brass flanges and be flush with the finished floor. All cover plate options shall provide for both power and communication services.
				a.	Flanges shall also accommodate Ortronics workstation connectivity outlets and modular inserts, and Pass & Seymour Techchoice Modular Inserts. Modular inserts shall snap directly into each flange through use of a mounting bezel.
				b.	Flange Dimensions: Brushed aluminum and brass flange dimensions shall be as follows:
					1)	One-Gang:
						a)	Brass, 5.060 inches (128.524 mm) wide, 6.080 inches (154.432 mm) length.
						b)	Brushed aluminum, 4.920 inches (124.968 mm) wide, 5.940 inches (150.876 mm) length.
					2)	Two-Gang:
						a)	Brass, 9.185 inches (233.299 mm) wide, 6.080 inches (154.432 mm) length.
						b)	Brushed aluminum, 9.045 inches (229.743 mm) wide, 5.940 inches (150.876 mm) length.
					3)	Three-Gang:
						a)	Brass, 13.310 inches (338.074 mm) wide, 6.080 inches (154.432 mm) length.
						b)	Brushed aluminum, 13.170 inches (334.518 mm) wide, 5.940 inches (150.876 mm) length.
			14.	Communication Modules Mounting Accessories: Flanges shall also accommodate Ortronics workstation connectivity outlets and modular inserts, and Pass & Seymour Techchoice Category 6 discrete keystone connectors. Modular inserts shall snap directly into each flange through use of a mounting bezel.
	** NOTE TO SPECIFIER ** In the following paragraph, retain only those products that are to be incorporated into the project and delete the others.
		D.	Fire Classified Resource RFB Series: Boxes shall be available in two-, or four-gang configurations and in a stamped-steel version. Boxes shall also be rectangular in shape and available in deep and shallow versions. All boxes shall also provide pre- and post-pour adjustment. All boxes shall also provide a removable barrier and tunnels between the individual compartments for greater capacity when required.
	** NOTE TO SPECIFIER ** Delete model not required.
			1.	RFB2FC Series Floor Box by Wiremold/Legrand: Manufactured from stamped steel and approved for use on above grade floors. The box shall be 13-1/8 inches L by 6-1/2 inches W by 3-7/16 inches H (333mm by 165mm by 87mm). There shall be two (2) independent wiring compartments that allow capacity for up to two (2) duplex receptacles and/or communication services. The RFB2 Series Box shall permit tunneling from end power compartment to end power compartment. Each of the two (2) compartments shall have a minimum wiring capacity of 50 cu in (822 ml3).
				a.	The box shall include two (2) intumescent stems with a 1-1/4-inch (31mm) diameter pass-through channel that allows the pathway to close off during a fire. The box shall provide an insulated assembly that will go on the underside of the floor structure to slow down the transfer of heat to the floor box.
				b.	The box shall be fully adjustable, providing a maximum of 1-3/8-inch (35mm) pre-pour adjustment, and a maximum of 3/4-inch (19.1mm) after-pour adjustment. The minimum depth of concrete shall be 4-1/2 inches (114mm). The box shall provide a series of device mounting plates that will accept both duplex power devices, as well as plates that will accommodate Ortronics workstation connectivity outlets and modular inserts, the Pass & Seymour Network Wiring System, and other open system devices.
			2.	RFB2-SSFC Series Floor Box by Wiremold/Legrand: Manufactured from stamped steel and approved for use on above grade floors. The box shall be 13-1/8 inches L by 6-1/2 inches W by 2-5/8 inches H (333mm by 165mm by 67mm). There shall be two (2) independent wiring compartments that allow capacity for up to two (2) duplex receptacles and/or communication services. The RFB2-SS Series Box shall permit tunneling from end power compartment to end power compartment. Each of the two (2) compartments shall have a minimum wiring capacity of 38 cu in (622 ml3).
				a.	The box shall include two (2) intumescent stems with a 1-1/4-inch (31mm) diameter pass-through channel that allows the pathway to close off during a fire. The box shall provide an insulated assembly that will go on the underside of the floor structure to slow down the transfer of heat to the floor box.
				b.	The box shall be fully adjustable, providing a maximum of 1-3/8-inch (35mm) pre-pour adjustment, and a maximum of 3/4-inch (19.1mm) after-pour adjustment. The minimum depth of concrete shall be 3-1/4 inches (83mm). The box shall provide a series of device mounting plates that will accept both duplex power devices, as well as plates that will accommodate Ortronics workstation connectivity outlets and modular inserts, the Pass & Seymour Network Wiring System, and other open system devices.
			3.	RFB4-4DBFC Series Floor Boxes by Wiremold/Legrand: Manufactured from stamped steel and approved for use on above grade floors. The box shall be 12-3/4 inches L by 10 inches W by 3-7/16 inches H (324mm by 254mm by 87mm). There shall be four (4) independent wiring compartments that allow capacity for up to four (4) duplex receptacles and/or communication services. The RFB4 Series Box shall permit tunneling from end power compartment to end power compartment. The RFB4-4DB Series Box shall permit tunneling from adjacent or opposite compartments. Two (2) of the four (4) compartments shall have a minimum wiring capacity of 16.4 cu in (269cu cm), one (1) compartment shall have a minimum capacity of 32.3 cu in (529cu cm), and one (1) compartment shall have a minimum capacity of 50 cu in (820cu cm).
				a.	The box shall include two (2) intumescent stems with a 1-1/4-inch (31mm) diameter pass-through channel that allows the pathway to close off during a fire. The box shall provide an insulated assembly that will go on the underside of the floor structure to slow down the transfer of heat to the floor box.
				b.	The box shall be fully adjustable, providing a maximum of 1-7/8-inch (47.7mm) pre-pour adjustment, and a maximum of 3/4-inch (19.1mm) after-pour adjustment. The minimum depth of concrete shall be 4-1/2 inches (114mm). The box shall provide a series of device mounting plates that will accept both duplex power devices, as well as plates that will accommodate Ortronics workstation connectivity outlets and modular inserts, the Pass & Seymour Network Wiring System, and other open system devices.
			4.	RFB4-SSFC Series Floor Box by Wiremold/Legrand: Manufactured from stamped-steel and approved for use on above grade floors. The box shall be 13-5/8 inches L by 10 inches W by 2-7/16 inches H (346mm by 254mm by 62mm). There shall be four (4) independent wiring compartments that allow capacity for up to four (4) duplex receptacles and/or communication services. The RFB4-SS Series Box shall permit feed through tunneling from adjacent compartments. Two (2) of the four (4) compartments shall have a minimum wiring capacity of 15.7 cu in (257cu cm), and two (2) compartments shall have a minimum wiring capacity of 31.2 cu in (511cu cm).
				a.	The box shall include two (2) intumescent stems with a 1-1/4-inch (31mm) diameter pass-through channel that allows the pathway to close off during a fire. The box shall provide an insulated assembly that will go on the underside of the floor structure to slow down the transfer of heat to the floor box.
				b.	The box shall be fully adjustable, providing a maximum of 1-7/8-inch (48mm) pre-pour adjustment, and a maximum of 3/4-inch (19.1mm) after-pour adjustment. The minimum depth of concrete shall be 3-1/4 inches (83mm).
	** NOTE TO SPECIFIER ** Select one of the finishes in the following subparagraph and delete the others.
			5.	Activation Cover: Manufactured of die-cast aluminum or die-cast zinc, and finished in (brushed aluminum) (plated brass) (powder-coated paint). Activation covers shall be available in flanged and flangeless versions. Covers shall be available with options for tile or carpet inserts, flush covers. The activation cover shall have been evaluated by UL to meet the applicable U.S. and Canadian safety standards for scrub water exclusion when used on tile, terrazzo, wood, and carpet covered floors.
				a.	Flanged Cover Size: 7-3/4 inches L by 6-9/16 inches W (197mm by 167mm).
	** NOTE TO SPECIFIER ** In the following paragraph, retain only those products that are to be incorporated into the project and delete the others.
		E.	Fire Classified Nonmetallic Floor Boxes: Boxes shall be manufactured through the use of injection molded Geon M3900 PVC material. The box shall be round or rectangular in shape. Box shall also have concrete depth markings on the exterior of the box to indicate box depth at the time of the pour. Box shall also provide graduated cubic inch markings on the interior of the box to indicate volume capacity at the appropriate box depth.
	** NOTE TO SPECIFIER ** Delete model not required.
			1.	Model: 880MPFC Fire Classified Floor Boxes as manufactured by Wiremold/Legrand.
			2.	Model: 881FC Fire Classified Floor Boxes as manufactured by Wiremold/Legrand.
			3.	Box shall accommodate concrete depths from 3-1/2 inches (89 mm) minimum to six (6) inches (152mm) maximum.
				a.	Boxes shall include intumescent material on the inside of the box to maintain the fire classification of the floor.
			4.	Rectangular floor boxes shall provide two (2) 1-1/4-inch (32mm) conduit openings to feed cabling to the box. Box shall provide the means to reduce this opening to fit 1-inch (25mm), 3/4-inch (19mm) and 1/2-inch (13mm) conduit sizes. Round floor boxes shall provide four (4) 1-inch (25mm) conduit openings to feed cabling to the box. Box shall provide the means to reduce this opening to fit 3/4-inch (19 mm) and 1/2-inch (13 mm) conduit sizes.
				a.	Equip boxes with a high impact mudcap to protect the box from damage and prevent concrete entry during the pour and debris entry after the pour. The mudcap shall withstand loads up to 700-lbs over a 2-inch (50.8mm) diameter. Box shall also be provided with ratchet teeth along interior box walls to attach cover. Box shall include internal spacer to prevent deformation of the box sidewalls when high temperature additives are used in the concrete pour.
			5.	Adjusting rings shall be used to attach flanges and covers to the floor box body. Adjusting ring shall have ratchet teeth to align with the teeth on box wall to connect box body without the use of adhesive or mechanical fasteners. Adjusting ring shall provide for 10 degrees of adjustment after concrete pour to adjust to various concrete conditions and floor finishes. Provide brass inserts to mount finish flanges to box body. Adjusting ring shall also provide for grounding locations using brass inserts.
			6.	Adjusting ring shall provide the ability to accept a modular connectivity system. Modular communication inserts shall snap directly into the adjusting ring openings. Adjusting ring for the rectangular box shall provide a fiber storage loop to maintain proper fiber optic bend radius control and excess fiber storage. Each adjusting ring shall except up to six connectivity activation locations. Adjusting ring shall allow modular connectivity inserts to be mounted recessed and protected when not in use.
			7.	Covers and Flanges: Floor box options shall accept brass and brushed aluminum cover plates and flanges. Rectangular flanges for brass and brushed aluminum cover plates shall be available in a one-gang application. Round flanges for brass and brushed aluminum covers plates shall be available in single application. Each flange shall provide 1/2-inch (13mm) of adjustment to accommodate various floor coverings and concrete depths.
			8.	Flanges shall accommodate connectivity outlets and modular inserts.
			9.	Modular inserts shall snap directly into each flange using a mounting bezel.
	** NOTE TO SPECIFIER ** Delete if not required.
	2.9	FLOOR BOXES FOR RAISED FLOORS
		A.	Classification and Use: Floor boxes shall have been examined and tested by Underwriters Laboratories Inc. to comply with UL514A and/or UL514C and Canadian Standard C22.2, No. 18-98 and bear the U.S. and Canadian UL Listing Mark. Fire classified floor boxes shall also have been tested by UL and classified for fire resistance and bear the U.S. and Canadian UL Classification Mark. The floor boxes shall conform to the standards set forth in the National Electrical Code, Section 300-21.
			1.	Floor boxes shall have been evaluated by UL to meet the applicable U.S. and Canadian safety standards.
			2.	These devices are not suitable for wet or damp locations, or other areas subject to saturation with water or other liquids such as commercial kitchens.
			3.	Floor boxes shall be suitable for use in air handling spaces in accordance with Section 300-22C of the National Electrical Code.
		B.	General: Round recessed raised and stage floor boxes provide an interface between power, communication and audio/visual (A/V) cabling in a raised floor and at the workstation or activation location where power, communication and/or A/V device outlets are required. These devices provide flush and recessed outlets that will not obstruct the floor area. Refer to the Drawings for types.
			1.	Round recessed raised and stage floor boxes shall be compatible with the complete line of Ortronics workstation connectivity outlets and modular inserts, or Pass & Seymour Network Wiring System.
		C.	General: Square raised floor boxes.
		D.	Raised Floor Boxes:
			1.	AC Series Raised Floor Boxes by Wiremold/Legrand.
				a.	5 sizes of steel raised floor boxes with die-cast covers that offer enough capacity for power and communication for all applications.
				b.	Cover Color: Gray.
			2.	AF Series Raised Floor Boxes by Wiremold/Legrand.
				a.	2 sizes of die-cast raised floor boxes with nonmetallic covers that provide up to 4 compartments for power and communication.
				b.	Cover Color: Black, Brown or Gray.
			3.	SAF Series Raised Floor Boxes by Wiremold/Legrand.
				a.	Shallow raised floor box for 2 1/2
			4.	861 Series Raised Floor Boxes by Wiremold/Legrand.
				a.	Single service flush round boxes with over 20 cover options.
			5.	CRFB Series Raised Floor Boxes by Wiremold/Legrand.
		E.	Configuration: Round recessed raised and stage floor boxes shall be available in a four-gang configuration. Boxes shall provide a removable barrier between the individual compartments for greater capacity when required.
	** NOTE TO SPECIFIER ** Delete finish not required.
			1.	Finish: Black powder-coated die-cast construction for boxes, covers and flanges.
			2.	Finish: Peened aluminum die-cast construction for boxes, covers and flanges.
	** NOTE TO SPECIFIER ** Delete products not required.
			3.	Product: Model CRFB-CR-BK.
			4.	Product: Model CRFB-CR-AL.
			5.	Product: Model CRFB-NR-BK.
			6.	Product: Model CRFB-NR-AL.
			7.	Body: Boxes shall be manufactured from die-cast aluminum with a stamped steel base. Boxes shall be available in a four-gang configuration. Overall box dimensions are 8 inches (203 mm) by 6-5/8 inches (168 mm) H.
	** NOTE TO SPECIFIER ** Delete tamper-resistant cover assembly requirement if not required.
			8.	Cover assembly shall be available in 1/4 turn latch or lockable tamper-resistant versions.
			9.	Communication covers shall accommodate Ortronics workstation connectivity outlets and modular inserts, Wiremold Connectivity Modular Insert System, and Extron Electronics MAAP devices.
			10.	Communication Modules Mounting Accessories: Flanges shall also accommodate Ortronics workstation connectivity outlets and modular inserts, and Pass & Seymour Techchoice Category 6 discrete keystone connectors. Modular inserts shall snap directly into each flange through use of a mounting bezel.
	2.10	FLOOR BOXES FOR WOOD FLOORS
		A.	Classification and Use: Provide floor boxes approved for use in wood floor construction. Boxes shall be approved for above grade (stamped steel) and on grade (epoxy coated stamped steel (spec locker), or nonmetallic) applications. Floor boxes shall have been examined and tested by Underwriters Laboratories Inc. to meet UL514A and Canadian Standard C22.2 and shall bear the appropriate label. Floor boxes shall conform to the standard set in the National Electrical Code. Multi-compartment box shall have been evaluated by UL to meet the applicable U.S. and Canadian safety standards for scrub water exclusion when used on tile, terrazzo, wood, and carpet covered floors.
		B.	Configurations: Boxes shall be available in one-, two-, or three-gang configurations or a single unit with two to eleven independent wiring compartments and available in stamped steel, epoxy coated stamped steel, and nonmetallic and versions. Boxes shall be rectangular in shape and available in deep and shallow versions. Boxes shall provide pre- and post-pour adjustments. Multiple gang boxes shall also provide a removable barrier between the individual compartments for greater capacity when required. Refer to Drawings for size and types.
			1.	Product: 880 Series Floor Boxes for Wood Floors by Wiremold/Legrand.
			2.	Product: 863 Series Round Floor Boxes by Wiremold/Legrand.
			3.	Product: 861 Series Round Floor Boxes by Wiremold/Legrand.
		C.	Metallic Floor Boxes:
			1.	Material: Stamped steel, formed; 1-3/4 inches (44 mm) pre-pour adjustment; 1/2 inch (13 mm) post-pour adjustment.
			2.	Material: Die-cast aluminum.
			3.	Provide removable barrier between individual compartments of multi-gang boxes.
	** NOTE TO SPECIFIER ** Aluminum not available on Cast boxes. Delete cover plate and flange materials not required.
			4.	Cover Plates and Flanges: Brushed brass.
			5.	Cover Plates and Flanges: Brushed aluminum.
			6.	Cover Plates and Flanges: Non-metallic.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
				a.	Black.
				b.	Brown.
			7.	Flange Color: Match cover colors.
			8.	Cover Plate and Flange Applications: To match floor box configuration.
			9.	Flanges shall accommodate connectivity outlets and modular inserts. Where indicated, provide connectivity outlets and modular inserts by Ortronics or approved equal.
			10.	Modular inserts shall snap directly into each flange through the use of a mounting bezel.
		D.	Nonmetallic Floor Boxes: Boxes shall be manufactured through the use of injection molded Geon M3900 PVC material. The box shall be round or rectangular in shape. Box shall allow for ganging of boxes together through the dovetail, interlocking mechanism. Knockouts shall be provided on the side walls of each box to provide for pass-through capability between each gang. Box shall also have concrete depth markings on the exterior of the box to indicate box depth at the time of the pour. Box shall also provide graduated cubic inch markings on the interior of the box to indicate volume capacity at the appropriate box depth.
			1.	Knockouts:
				a.	Rectangular floor boxes shall provide two 1-1/4 inches (32 mm) openings, adjustable to accommodate 1/2 inch (13 mm), 3/4 inch (19 mm) and 1 inch (25 mm) trade size conduits.
				b.	Round floor boxes shall provide four 1 inch (25mm) conduit opening to feed cabling to the box. Box shall provide the means to reduce this opening to fit 3/4 inch (19 mm) and 1/2 inch (13 mm) conduit sizes.
			2.	Adjusting rings shall be used to attach flanges and covers to the floor box body. Adjusting ring shall have ratchet teeth to align with the teeth on box wall to connect box body without the use of adhesive or mechanical fasteners. Adjusting ring shall provide for 10 degrees of adjustment after concrete pour to adjust to various concrete conditions and floor finishes. Provide brass inserts to mount finish flanges to box body. Adjusting ring shall also provide for grounding locations using brass inserts.
			3.	Adjusting ring shall provide the ability to accept a modular connectivity system. Modular communication inserts shall snap directly into the adjusting ring openings. Adjusting ring for the rectangular box shall provide a fiber storage loop to maintain proper fiber optic bend radius control and excess fiber storage. Each adjusting ring shall except up to six connectivity activation locations. Adjusting ring shall allow modular connectivity inserts to be mounted recessed and protected when not in use.
			4.	Covers and Flanges: Flanges shall be available in one-, two-, and three-gang applications. Rectangular flanges for brass, brushed aluminum and nonmetallic cover plates shall be available in one-, two-, and three-gang applications. Round flanges for brass, brushed aluminum and nonmetallic covers plates shall be available in single and multiservice applications. Each flange shall provide 1/2 inch (13 mm) of adjustment to accommodate various floor coverings and concrete depths.
	** NOTE TO SPECIFIER ** Delete the following paragraphs not required.
				a.	Cover Plates and Flanges: Brass.
				b.	Cover Plates and Flanges: Brushed Aluminum.
				c.	Cover Plates and Flanges: Non-metallic.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
				d.	Black.
				e.	Brown.
			5.	Flanges shall accommodate connectivity outlets and modular inserts.
			6.	Modular inserts shall snap directly into each flange using a mounting bezel.
		E.	Multi-Compartment Floor Boxes: Two to eleven independent wiring compartments allow up to eleven duplex receptacles/communications services; tunneling feature allows internal wiring to various compartments; fully adjustable box, providing maximum 1-7/8 inches (48 mm) pre-pour and maximum 3/4 inch (19 mm) post-pour adjustments.
	** NOTE TO SPECIFIER ** Cast iron not available in shallow depth. Delete depth not required.
			1.	Depth: Deep.
			2.	Depth: Shallow.
			3.	Boxes shall provide a series of device mounting plates that will accept duplex power devices, audio/visual devices as well as plates that will accommodate connectivity outlets and modular inserts. Where scheduled, provide connectivity outlets and modular inserts by Ortronics or approved equal.
			4.	Activation Covers shall be available with options for tile or carpet inserts, blank covers, or covers with concentric 1-1/4 inches (32 mm) and 2 inches (51 mm) trade size plug openings for furniture feed applications as scheduled.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
				a.	Activation Cover: Die-cast aluminum - Flanged.
				b.	Activation Cover: Die-cast aluminum - Flangeless.
	** NOTE TO SPECIFIER ** Delete two of the following three paragraphs.
				c.	Activation Cover Finish: Brushed aluminum.
				d.	Activation Cover Finish: Black powder-coated.
				e.	Activation Cover Finish: Brass plated finish.
	** NOTE TO SPECIFIER ** This specification covers firestop devices for use in through-penetration firestop systems, which are used to maintain the fire rating of the wall or floor, as well as to route and protect power and/or communications cable distribution for commercial, institutional, industrial and utility needs. Delete if not required.
	2.11	FIRE STOP THRU-WALL/THRU-FLOOR FITTINGS
		A.	Classification and Use: The firestop device for use in through-penetration firestop systems shall have been examined and tested by Underwriters Laboratories Inc. to UL1479 (ASTM E 814) and bear the U.S. and Canadian UL Classification Mark. The device shall be classified for use in one-, two-, three-, and four-hour rated gypsum, concrete and block walls and provide a maximum L rating of 3.3 cfm. The device shall be classified for use in one-, two-, and three-hour rated concrete floors having a minimum 4-1/2 inches (114 mm) thick reinforced lightweight or normal weight (100 to 150 pcf) (1600 to 2400 kg/cu. m). The devices shall also been tested by Underwriters Laboratories Inc. to UL2043 and determined to be suitable for use in air handling spaces.
		B.	Product: FlameStopper Thru-Wall /Floor Fitting as manufactured by Wiremold/Legrand.
	** NOTE TO SPECIFIER ** Delete size not required.
			1.	Size: Accommodates 2 inches (51 mm) diameter EMT conduit.
			2.	Size: Accommodates 4 inches (102 mm) diameter EMT conduit.
	** NOTE TO SPECIFIER ** Delete finish not required.
			3.	Finish: Red powder coat.
			4.	Finish: Custom color as scheduled.
			5.	Finish: Unpainted galvanized.
		C.	Construction:
			1.	The firestop device box shall be constructed of 17 gauge G90 steel.
			2.	The firestop device intumescent block shall be constructed of a graphite base material with expansion starting at 375 degrees F and an unrestrained expansion between 6 to 12 times. The intumescent block shall be held securely by the box in order to prevent tampering and damage during installation.
			3.	The firestop device shall have doors which can be adjusted to prevent materials from penetrating the device if the device is empty or completely full. The doors shall be constructed of 16 gauge G90 steel with No. 10-32 screws use to adjust opening size.
	** NOTE TO SPECIFIER ** For retrofit applications where an existing in-wall conduit extends out from the wall more than 7/8" [22mm], the Wiremold Heat Shield must be used in order to maintain UL Fire Classification. The firestop device is then installed onto the heat shield. Delete if not required.
			4.	Retrofit Accessory: Wiremold Heat Shield.
	** NOTE TO SPECIFIER ** For retrofit applications where no conduit is installed in the wall to protect existing cables, the Wiremold split conduit assembly should be used to protect cables. After installing the split conduit within the wall, the Wiremold wall plate should be installed to cover any irregularly shaped hole cut in the wall. The firestop device is then installed onto the conduit. Delete if not required.
			5.	Retrofit Accessory: Wiremold Split Conduit Assembly.
	** NOTE TO SPECIFIER ** Delete product if not required.
	2.12	POKE-THRU SYSTEMS
		A.	Classification and Use: Poke-thru device use is limited by the UL Fire Resistance Directory to a minimum spacing of 2 feet (610 mm) on center and not more than one device per 65 square feet (6 square meters) of floor area in each span. Poke-thru device shall have been examined and tested by Underwriters Laboratories Inc. to comply with UL514A and/or UL514C, as applicable and tested to Canadian Standard C22.2 and bear the cULus mark. The poke-thru shall conform to the standards set in the National Electrical Code, Section 300-21.
			1.	Poke-thru device shall be for use in 1, 1-1/2, or 2-hour rated, unprotected reinforced concrete floors and 1, 1-1/2, or 2 hour rated floors employing unprotected steel floor units and concrete toppings (D900 Series designs), or concrete floors with suspended ceilings. Fire resistive designs with suspended ceilings shall have provisions for accessibility in the ceiling below the poke-thru device fittings.
			2.	Poke-thru device shall have been evaluated by UL to meet the applicable U.S. and Canadian safety standards for scrub water exclusion when used on tile, terrazzo, wood, and carpet covered floors.
			3.	Poke-thru device shall be suitable for use in air handling spaces in accordance with Section 300-22C of the National Electrical Code.
	** NOTE TO SPECIFIER ** Delete series if not required.
		B.	Furniture Feed Poke-Thru Systems:
			1.	Product: Wiremold RC7FFTC Tile and Carpet Furniture Feed by Wiremold/Legrand.
			2.	Insert: One 3/4 inch (19 mm) conduit connected to insert body and one 24-1/2 cubic inch (0.4 cubic mm) stamped steel junction box for wire splices and connections; body of intumescent fire stop material to maintain floor slab fire-rating.
			3.	Channels: One 3/4 inch (19 mm) channel for power; two 1/2 inch (13 mm) channels for communication cabling, with communication cables conduit protected and connected to insert body.
			4.	Activation Cover: Three conduit openings with one piece die-cast aluminum alloy carpet flange; gasket to maintain scrub water tightness; virtually flush with floor.
	** NOTE TO SPECIFIER ** Delete finishes not required.
				a.	Finish: Gray; two-stage epoxy paint.
				b.	Finish: Black; two-stage epoxy paint.
				c.	Finish: Ivory; two-stage epoxy paint.
				d.	Finish: Plated brass.
				e.	Finish: Brushed aluminum.
	** NOTE TO SPECIFIER ** Delete series if not required.
		C.	Furniture Feed Poke-Thru Systems:
			1.	Product: Wiremold 4FFATC Insert Body by Wiremold/Legrand: Furnish with one 3/4 inch (19 mm) trade size channel for power, and one 1-1/4 inches (32 mm) trade size channel for communication cabling.
	** NOTE TO SPECIFIER ** Delete finishes not required.
				a.	Finish: Gray; two-stage epoxy paint.
				b.	Finish: Black; two-stage epoxy paint.
				c.	Finish: Plated brass.
				d.	Finish: Brushed aluminum.
			2.	Product: Wiremold 6ATCFF Evolution Series by Wiremold/Legrand: Furnish with 3/4 inch (19 mm) conduit for outer channel. Maximum 2 inch (51 mm) which takes up the center channel and one outer channel.
	** NOTE TO SPECIFIER ** Delete finishes not required.
				a.	Finish: Gray; two-stage epoxy paint.
				b.	Finish: Bronze.
				c.	Finish: Plated brass.
				d.	Finish: Nickel.
			3.	Product: Wiremold RC9AM2TC Insert Body by Wiremold/Legrand: Furnish with 2-inch (51mm) trade size conduit stem for either all power or all communication.
	** NOTE TO SPECIFIER ** Delete finishes not required.
				a.	Finish: Gray; two-stage epoxy paint.
				b.	Finish: Black; two-stage epoxy paint.
				c.	Finish: Brushed aluminum.
			4.	Product: Wiremold RC9AFFTC Tile and Carpet Furniture Feed by Wiremold/Legrand.
				a.	Finish: Gray; two-stage epoxy paint.
				b.	Finish: Black; two-stage epoxy paint.
			5.	Insert: Body of intumescent fire stop material to maintain floor slab fire rating.
			6.	Channels: One 1/2 inch (13 mm) channel for power; two 1-1/4 (32 mm) inch channels for communication cabling, with communication cables conduit protected and connected to insert body.
			7.	Activation Service Head: Die-cast aluminum alloy 7 inch (178 mm) diameter trim flange and 2-5/32 inch (55 mm) high by 5-1/2 inch (140 mm) diameter hexagonal service head; six openings for power/communications requirements; five openings with rubber grommet material for cable pass-through; one opening with zinc die-cast threaded drop-in hub to accept 3/4 inch (19 mm) conduit connector; gasket to maintain scrub water tightness.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
	** NOTE TO SPECIFIER ** Delete series if not required.
		D.	Flush Poke-Thru Systems:
			1.	Product: RC7 Series Tile and Carpet Flush Poke-Thru Devices by Wiremold/Legrand.
			2.	Product: RC9 Series Flush Poke-Thru Devices by Wiremold/Legrand.
			3.	Product: RC9AMD Series Tile and Carpet Flush Poke-Thru Devices by Wiremold/Legrand.
			4.	Product: RC3 Series Tile and Carpet Flush Poke-Thru Devices by Wiremold/Legrand.
			5.	Product: RC4 Series Flush Poke-Thru Devices by Wiremold/Legrand.
			6.	Product: AV3 Series Flush Poke-Thru Devices by Wiremold/Legrand.
			7.	Product: AMD8 Series Flush Poke-Thru Devices by Wiremold/Legrand.
	** NOTE TO SPECIFIER ** Delete series if not required. Activations on recessed poke-thru systems are recessed below floor surface for added protection
		E.	Recessed Poke-Thru Systems:
			1.	Product: 6AT Series Flush Poke-Thru Devices by Wiremold/Legrand.
				a.	Designed for a 6 inches (152mm) core hole and provides up to two and one-half (2 1/2) gangs of power, communication, or A/V capability.
			2.	Product: 8AT Series Flush Poke-Thru Devices by Wiremold/Legrand.
				a.	Designed for an 8 inches (203mm) core hole and provides up to four (4) gangs of power, communication, or A/V capability.
			3.	For use on carpet, tile, terrazzo, or wood covered floors as scheduled or required. Refer to drawings.
			4.	Insert: Body of intumescent fire stop material to maintain floor slab fire rating.
			5.	Channels: One 3/4 inch (19 mm) channel for power; two 1/2 inch (13 mm) channels for communication cabling, with communication cables conduit protected and connected to insert body.
			6.	Receptacles: Four, maximum; as scheduled on drawings.
			7.	Brackets: Non-metallic, with integral grommet at communication compartment opening; accommodates four connectivity modular inserts, maximum.
			8.	Activation Cover: Die-cast aluminum alloy; gasket to maintain scrub water tightness.
	** NOTE TO SPECIFIER ** Delete finishes not required.
				a.	Finish: Gray; two-stage epoxy paint.
				b.	Finish: Black; two-stage epoxy paint.
				c.	Finish: Bronze.
				d.	Finish: Plated brass.
				e.	Finish: Nickel.
			9.	Activation Slide Cover: Textured PVC; spring-loaded slides (spec locker) that snap back in place when not in use to protect flush mounted power receptacle; Finish to match cover.
	** NOTE TO SPECIFIER ** Delete series if not required.
		F.	Pedestal-Style Poke-Thru Systems:
			1.	Product: FIT Series Tile and Carpet Flush Poke-Thru Devices by Wiremold/Legrand.
			2.	For use on carpet, tile, terrazzo, or wood covered floors as scheduled or required. Refer to drawings.
			3.	Insert: Body of intumescent fire stop material to maintain floor slab fire rating.
			4.	Channels: There shall be a 1 inch (25 mm) trade size conduit channel with an integral divider for running both power and communication cabling.
			5.	Junction box (when used for power only) offers 30 cu. inches (492 ml) of volume capacity. When used for power and communication, the junction box offers 25 cu. inches (410 ml) of capacity in the power compartment.
			6.	Activation Service Head: The activation service head shall be manufactured of .125 inch (3.1 mm) clear anodized aluminum. Service heads shall come in single width and double width configurations. Service heads shall attach directly to the insert body. A gasket is attached to the underside of the service heads to maintain scrub water tightness. Service heads shall also provide a barrier to complete isolation of power and communication cables throughout the poke-thru assembly. Manufacturer shall utilize faceplates to provide power and communication services.
			7.	Faceplates shall be manufactured of a .086 inch (2.2 mm) clear anodized aluminum.
			8.	Manufacturer shall provide faceplates that accept Ortronics workstation connectivity outlets and modular inserts, or the Pass & Seymour Network Wiring System. Modular inserts shall snap directly into each faceplate through use of a mounting bezel. Faceplate dimensions shall be 9 inches (229 mm) L by 2-1/2 inches (64 mm) H.
	** NOTE TO SPECIFIER ** Delete series if not required.
		G.	Pedestal-Style Poke-Thru Systems:
			1.	Product: RC91GHBTC, RC92HGBTC Series Tile and Carpet Flush Poke-Thru Devices by Wiremold/Legrand.
			2.	For use on carpet, tile, terrazzo, or wood covered floors as scheduled or required. Refer to drawings.
			3.	Insert: Body of intumescent fire stop material to maintain floor slab fire rating.
			4.	Channels: There shall be one 1/2 inch (13 mm) trade size conduit channel and one 1-1/4 inches (32 mm) trade size conduit channel for power and communication cabling.
			5.	Activation Service Head: The activation service head shall be manufactured of .125 inch (3.1 mm) clear anodized aluminum. Service heads shall come in single width and double width configurations. Service heads shall attach directly to the insert body. A gasket is attached to the underside of the service heads to maintain scrub water tightness. Service heads shall also provide a barrier to complete isolation of power and communication cables throughout the poke-thru assembly. Manufacturer shall utilize faceplates to provide power and communication services.
			6.	Faceplates shall be manufactured of a .086 inch (2.2 mm) clear anodized aluminum.
			7.	Manufacturer shall provide faceplates that accept Ortronics workstation connectivity outlets and modular inserts, or the Pass & Seymour Network Wiring System. Modular inserts shall snap directly into each faceplate through use of a mounting bezel. Faceplate dimensions shall be 9 inches (229 mm) L by 2-1/2 inches (64 mm) H.
	** NOTE TO SPECIFIER ** Delete series if not required.
		H.	Pedestal-Style Poke-Thru Systems:
			1.	Product: RC9AFF Series Furniture Feed Style Flush Poke-Thru Devices with Hexagonal Service Head by Wiremold/Legrand.
			2.	For use on carpet, tile, terrazzo, or wood covered floors as scheduled or required. Refer to drawings.
			3.	Insert: Body of intumescent fire stop material to maintain floor slab fire rating.
			4.	Channels: There shall be one 1/2 inch (13 mm) trade size conduit channel and one 1-1/4 inches (32 mm) trade size conduit channel for power and communication cabling.
			5.	Activation Service Head: The activation service head shall be manufactured of .125 inch (3.1 mm) clear anodized aluminum. Service heads shall come in hexagonal shape. Service heads shall attach directly to the insert body. A gasket is attached to the underside of the service heads to maintain scrub water tightness. Service heads shall also provide a barrier to complete isolation of power and communication cables throughout the poke-thru assembly. Manufacturer shall utilize faceplates to provide power and communication services.
			6.	Faceplates shall be manufactured of a .086 inch (2.2 mm) aluminum.
			7.	Flanges: Galvanized (unfinished), gray or black as selected.
			8.	Manufacturer shall provide faceplates that accept Ortronics workstation connectivity outlets and modular inserts, or the Pass & Seymour Network Wiring System. Modular inserts shall snap directly into each faceplate through use of a mounting bezel. Faceplate dimensions shall be 9 inches (229 mm) L by 2-1/2 inches (64 mm) H.
	** NOTE TO SPECIFIER ** Delete series if not required.
		I.	Recessed Poke-Thru Systems:
			1.	Product: Evolution 6AT Series Poke-Thru Devices by Wiremold/Legrand.
			2.	This assembly consists of an insert and an activation cover. Overall poke-thru assembly length shall be 16-3/4 inches (425mm).
			3.	Insert: The insert body shall recess the devices a minimum of 2-3/4 inches (69 mm) and have a polyester based backing enamel finished interior (ivory). There shall be the necessary channels to provide complete separation of power and communication services. There shall be three compartments that allow for up to three duplex receptacles that can be wired as a standard receptacle or isolated ground and/or twelve communication ports and/or ten of Extron Electronics MAAP and/or two AAP devices.
				a.	The body will consist of an intumescent fire stop material to maintain the fire rating of the floor slab. The intumescent material will be held securely in place in the insert body and shall not have to be adjusted to maintain fire rating of the unit and the floor slab. The insert shall have retaining feature that will hold the poke-thru device in the floor slab without additional fasteners. The poke-thru insert shall also consist of a 3/4 inch trade size conduit stub that is connected to the insert body and a 24.5 cu. in. (402ml) stamped steel junction box for wire splices and connections. The stamped steel junction box shall also contain the necessary means to electrically ground the poke-thru device to the system ground.
			4.	Activation Cover: The activation covers shall be manufactured of die-cast aluminum alloy and be available in powder-coated gray, black, or plated in brass, nickel or bronze finish. Two gaskets (one for carpet and one for tile) are provided to go under the trim flange to maintain scrub water tightness. The activation cover shall be 7-1/4 inches (184mm) in diameter. The activation covers shall be available in carpet and tile versions. The carpet covers shall be surface mounted and the tile covers shall be flush with the finished floor covering. The cover shall have spring loaded slides to allow cables to egress out of the unit and maintain as small an egress opening as possible.
				a.	Mounting Accessories: The activation shall have three locations to mount communication connectors. Connectors shall be mounted using a mounting bracket. Mounting brackets shall be provided to mount up to twelve Ortronics TracJack Category 6 insert modules or TechChoice Category 6 discrete keystone connectors. The unit will also be supplied with two Category 6 keystone connectors and two Lucent keystones. The unit shall also accommodate a mechanism to permit protection of communication cabling. This mechanism shall be stamped steel construction and accept both flexible and rigid conduit. This mechanism shall accept 3/4 inch, 1-1/4 inches or 2 inches trade size conduits.
	** NOTE TO SPECIFIER ** Delete series if not required.
		J.	Recessed Poke-Thru Systems:
			1.	Product: Evolution 8AT Series Poke-Thru Devices by Wiremold/Legrand.
			2.	This assembly consists of an insert and an activation cover. Overall poke-thru assembly length shall be 16-3/4 inches.
			3.	Insert: The insert body shall recess the devices a minimum of 2-3/4 inches (69 mm) and have a polyester based backing enamel finished interior (ivory). There shall be the necessary channels to provide complete separation of power and communication services. There shall be five compartments that allow for up to five duplex receptacles that can be wired as a standard receptacle or isolated ground and/or twenty-two communication ports and/or sixteen of Extron Electronics MAAP and/or four AAP devices.
				a.	The body will consist of an intumescent fire stop material to maintain the fire rating of the floor slab. The intumescent material will be held securely in place in the insert body and shall not have to be adjusted to maintain fire rating of the unit and the floor slab. The insert shall have retaining feature that will hold the poke-thru device in the floor slab without additional fasteners. The poke-thru insert shall also consist of a 3/4 inches trade size conduit stub that is connected to the insert body and a 24.5 cu. in. (402ml) stamped steel junction box for wire splices and connections. The stamped steel junction box shall also contain the necessary means to electrically ground the poke-thru device to the system ground.
			4.	Activation Cover: The activation covers shall be manufactured of die-cast aluminum alloy and be available in powder-coated gray, black, or plated in brass, nickel or bronze finish. Two gaskets (one for carpet and one for tile) are provided to go under of the trim flange to maintain scrub water tightness. The activation cover shall be 9-1/4 inches (235mm) in diameter. The activation covers shall be available in carpet and tile versions. The carpet covers shall be surface mounted and the tile covers shall be flush with the finished floor covering. The cover shall have spring loaded slides to allow cables to egress out of the unit and maintain as small an egress opening as possible.
			5.	Mounting Accessories: The activation shall have three locations to mount communication connectors. Connectors shall be mounted using a mounting bracket. Mounting brackets shall be provided to mount up to twelve Ortronics TracJack Category 6 insert modules or TechChoice Category 6 discrete keystone connectors. The unit will also be supplied with two Category 6 keystone connectors and two Lucent keystones. The unit shall also accommodate a mechanism to permit protection of communication cabling. This mechanism shall be stamped steel construction and accept both flexible and rigid conduit. This mechanism shall accept 3/4 inch, 1-1/4 inches or 2 inches trade size conduits.
	** NOTE TO SPECIFIER ** Delete series if not required.
		K.	Recessed Poke-Thru Systems:
			1.	Product: Evolution 6AFF Series Poke-Thru Devices by Wiremold/Legrand.
			2.	This assembly consists of an insert and an activation cover. Overall poke-thru assembly length shall be 16-3/4 inches (425mm).
			3.	Insert: The insert body shall have the necessary channels to provide complete separation of power and communication services. There shall be two channels that allow for up to ten #10 AWG conductors in the power channel and twenty-eight category 6A data cables through the communication channel.
				a.	The body will consist of an intumescent fire stop material to maintain the fire rating of the floor slab. The intumescent material will be held securely in place in the insert body and shall not have to be adjusted to maintain fire rating of the unit and the floor slab. The insert shall have retaining feature that will hold the poke-thru device in the floor slab without additional fasteners. The poke-thru insert shall also consist of a 3/4 inches trade size conduit stub that is connected to the insert body and a 24.5 cu. in. (402ml) stamped steel junction box for wire splices and connections. The stamped steel junction box shall also contain the necessary means to electrically ground the poke-thru device to the system ground.
			4.	Activation Cover: The activation covers shall be manufactured of die-cast aluminum alloy and be available in powder-coated gray, black, or plated in brass, nickel or bronze finish. Two gaskets (one for carpet and one for tile) are provided to go under the trim flange to maintain scrub water tightness. The activation cover shall be 7-3/4 inches (196mm) in diameter. The activation covers shall be available in the surface mount (carpet) version. The cover shall have one (1) 3/4 inch (19.05mm) trade size opening for power and one (1) 1-1/4 inches / 2 inches (31.75/50.8) combination trade size opening for communications.
		L.	Communication Modules Mounting Accessories: The poke-thru manufacturer shall have available open modular inserts to facilitate mounting UTP (including Category 5, 5e, 6), STP, fiber optic, coaxial, and data/communications devices. The AV3 series shall accommodate Extron MAAP mini architectural adapter plates. Where indicated, provide connectivity outlets and modular inserts by Ortronics or approved equal.
		M.	Mounting: Units shall permit wiring to be completed at floor level. The units shall mount in either a 3-inch or 4-inch core hole as applicable. Installation shall be completed by pushing unit down into a cored hole. The specified poke-thru shall be UL listed to US and Canadian standards for use on carpet, tile, terrazzo, and wood covered floors.
	** NOTE TO SPECIFIER ** Delete series if not required.
	2.13	CABLE TRAY SYSTEMS
		A.	Cable Tray Systems: Provide cable tray system to route power and communications cable distribution for utility needs. Cable tray system shall consist of cable tray and appropriate fittings for a complete installation.
		B.	Classification and Use: Cable tray is to be utilized in locations only as covered in Section 12-2200 through 12-2212 of the Canadian Electric Code and Article 392 of the National Electric Code, as adopted by the National Fire Protection Association and as approved by the American National Standards Institute.
		C.	Cable Tray Systems:
			1.	Product: Wiremold SpecMate Cable Tray System by Wiremold/Legrand.
	** NOTE TO SPECIFIER ** Delete three of the following four paragraphs.
			2.	Construction: Aluminum alloy 6303-T6; trays formed to enable full viewing of cables. Center spine, consisting of center spine with two hollows, and rung with 1 inch (25 mm) of cable laying surface.
			3.	Construction: Aluminum alloy 6303-T6; trays formed to enable full viewing of cables. Twin spine, consisting of parallel center spines, and rung with 1 inch (25 mm) of cable laying surface.
			4.	Construction: Aluminum alloy 6303-T6; trays formed to enable full viewing of cables. Ladder tray, consisting of two longitudinal support side rails, and rungs with 7/8 inch (22 mm) of cable laying surface.
			5.	Construction: Aluminum alloy 6303-T6; trays formed to enable full viewing of cables. Wall mounted cable tray, consisting of support spine, and rungs with 1 inch (25 mm) of cable laying surface.
			6.	Tray Dimensions: As indicated on drawings.
			7.	Straight Section Rung Spacing: As indicated on drawings.
			8.	Inside Radius of Fittings: As indicated on drawings.
			9.	Provide plastic cap for ends of all rungs.
	** NOTE TO SPECIFIER ** Delete one of the following two paragraphs.
			10.	Fittings: ____________.
			11.	Fittings: Provide full compliment of fittings necessary to make system workable.
		D.	Cable Tray Systems:
			1.	Product: Wiremold SpecMate Solid Bottom Cable Tray System by Wiremold/Legrand;
	** NOTE TO SPECIFIER ** Delete material not required.
			2.	Material: Type G90 galvanized steel.
			3.	Material: Type A01 satin coat galvanized steel.
			4.	Material: ANSI type 304 stainless steel.
			5.	Material: Aluminum alloy 5052-H32.
	** NOTE TO SPECIFIER ** Delete flange not required.
			6.	Flange: Non-flanged.
			7.	Flange: Single return flange.
			8.	Flange: Double return flange.
			9.	Load Bearing Class: As selected by Architect.
			10.	Tray Dimensions: As indicated on drawings.
			11.	Inside Radius of Fittings: As indicated on drawings.
	** NOTE TO SPECIFIER ** Delete requirements not required.
			12.	Provide hinged and latched covers.
			13.	Provide ventilation louvers in base.
			14.	Provide ventilation louvers in cover.
			15.	Provide solid bottom form.
			16.	Fittings: Provide full compliment of fittings necessary to make system workable as scheduled or indicated.
	** NOTE TO SPECIFIER ** Delete if not required.
	2.14	SECURE SURFACE MOUNTED RACEWAYS
		A.	General:
			1.	System: Provide secure surface raceway and enclosure systems for SIPRNET, NIPRNET, JWICS, DoD, Federal Government and other sensitive information networks. Surface raceway system shall consist of raceway bases, covers, square 1 piece raceway (2 inchesx2 inches and 1 inchesx1 inches), secure (lockable) enclosures and appropriate fittings and device mounting plates necessary for a complete installation.
			2.	Configuration: Raceways shall be one-piece or two-piece design with base and structurally sound inter-locking cover, without the need for a distributive locking mechanism. 2-piece raceway shall be 4.75 inches (121mm) wide and 1-3/4 inches (45mm) deep with all seams located on the front of the raceway. 1-piece raceways shall be 2 inches by 2 inches (51mm by 51mm) or 1 inch by 1 inches (25mm by 25mm). Raceway couplings and fittings shall provide a 3 inches (76mm) overlap prevent covert and surreptitious entry. 2-piece raceway shall provide cable management brackets to facilitate cable ties. Provide raceways and enclosures from a company that can design and manufacture custom options where required. Note: Epoxy coating of seams and joints may be required - check with Designated (Local) Approval Authority for PDS requirements.
			3.	Fittings: Fittings shall include (but not limited to), internal and external elbows, tees, transitions, offsets, dropouts, end terminations, through wall, couplings for joining raceway sections, wire clips, blank end fittings, and device mounting brackets and plates as applicable. 2 inches by 2 inches and 1 inch by 1 inches raceway shall have universal tee and elbow fittings. Provide full capacity fittings to maintain a controlled 2 inches (51mm) cable bend radius, meeting the specification for Fiber Optic and UTP cabling and exceeding the TIA/EIA-569-A requirements for communications pathways.
			4.	Raceway and Fitting Mounting Brackets: Raceway system shall be secured to mounting surfaces using 1.5 inches (38mm) mounting brackets, providing 360 degree inspection capability of raceway and mounting hardware in compliance with NSTISSI 7003.
			5.	Enclosures: Enclosures shall have solid welded external seams, lockable doors with stainless steel hasps that accept Sargent & Greenleaf 8077AD padlocks, no external hinges and no pre-punched knock-outs are permitted. Enclosures which have raceway adapters, shall be factory welded.
			6.	Communications Devices and Accessories: Point of use enclosures shall accommodate a complete line of connectivity outlets and modular inserts for UTP (including Category 5, 5e, 6) STP (150 ohm) fiber optic, coaxial, and other cabling types with matching faceplates and bezels to facilitate mounting. Where indicated, provide connectivity outlets and modular inserts by Ortronics or approved equal.
		B.	Classification:
			1.	Surface raceways and enclosures shall be suitable for use in dry interior locations only.
			2.	Product shall meet or exceed requirements set out in NSTISSI 7003, Protective Distribution Systems as approved by the local/ Designated Approval Authority.
		C.	Secure Surface Mounted Metal Raceways: WSSR (2 piece), WSSR2x2 (1 piece), WSSR 1 by 1 (1 piece) manufactured by Wiremold/Legrand.
			1.	Material: WSSR2x2 - Type 409 SS, .055 inch wall. WSSR1x1 - Type 409 SS, .047 inch wall. WSSR - Galv-annealed mild steel, minimum thickness 0.048 inch (1.2mm).
			2.	Finish: Manufacturer's standard powder coat gloss ivory or custom color as selected.
			3.	Fittings: Fittings shall include (but not limited to), internal and external elbows, tees, transitions, offsets, dropouts, end terminations, through wall, couplings for joining raceway sections, wire clips, blank end fittings, and device mounting brackets and plates as applicable. 2 inches by 2 inches and 1 inch by 1 inch raceway shall have universal tee and elbow fittings. Provide full capacity fittings to maintain a controlled 2 inches (51mm) cable bend radius, meeting the specification for Fiber Optic and UTP cabling and exceeding the TIA/EIA-569-A requirements for communications pathways.
				a.	Fiber Optic/UTP/STP Fittings: Corner elbows, tees, and entrance end fittings as required to maintain a controlled 2 inches (51mm) nominal cable bend radius that meets the specifications for Fiber Optic and UTP/STP cabling and exceeds TIA 569 requirements for communications pathways.
				b.	Obstacle Avoidance and Offset Fittings: Provide fittings as required to bypass large and small obstacles and small offsets in supporting wall.
		D.	Communications Devices and Accessories: Point of use enclosures shall accommodate Ortronics workstation connectivity outlets and a complete line of connectivity outlets and modular inserts for UTP (including Category 5, 5e, 6) STP (150 ohm) fiber optic, coaxial, and other cabling types with matching faceplates and bezels to facilitate mounting.
	PART 3	EXECUTION
	3.1	EXAMINATION
		A.	Do not begin installation until substrates have been properly prepared.
		B.	If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
	3.2	PREPARATION
		A.	Clean surfaces thoroughly prior to installation.
		B.	Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
	3.3	INSTALLATION - GENERAL
		A.	Install in accordance with manufacturer's instructions for system components.
		B.	Install in accordance with complete system instruction sheets.
		C.	Install enclosures to be mechanically continuous and connected to all electrical outlets, boxes, device mounting brackets, and cabinets, in accordance with manufacturer's installation sheets.
		D.	Install enclosures to be electrically continuous and bonded in accordance with the National Electric Code for proper grounding.
	** NOTE TO SPECIFIER ** Delete if not required.
	3.4	POWER POLE INSTALLATION
		A.	Install indoor power poles and architectural columns in accordance with manufacturer's suggested installation instructions, and as specified. Locate the indoor power poles and architectural columns in strict accordance with the Drawings in order to maintain the indicated pole and column spacing.
		B.	Mechanical Security: Install system in such a manner that it is mechanically continuous and connected to all electrical outlets, boxes, and cabinets, in accordance with manufacturer's installation instructions.
		C.	Electrical Security: Install system in such a manner that it is electrically continuous and bonded in accordance with the provisions of the National Electric Code.
		D.	System Support: Securely support system at the ceiling and floor in accordance with manufacturer's installation instructions.
		E.	Install system complete with insulating bushings and inserts where required by manufacturer's installation instructions. Close all unused openings where wire is exposed.
	** NOTE TO SPECIFIER ** Delete if not required.
	3.5	SECURE NETWORK INSTALLATION
		A.	Strictly comply with manufacturer's installation instructions and recommendations and approved shop drawings. Coordinate installation with adjacent work to ensure proper clearances and to prevent electrical hazards. Ensure installation compliance with site CTTA (and/or DAA (Designated Approval Authority).
			1.	Mechanical Security: WSSR two piece raceway shall have structurally interlocking base seams and cover seams offset.
			2.	Raceway Support: Raceway shall be supported by 3 mounting brackets per 10 foot length. Raceway fittings shall be supported by 2 mounting brackets per fitting.
			3.	All pre-located raceway mounting holes shall be used to secure system in place.
			4.	Accessories: Provide accessories as required for a complete installation, where required by manufacturer.
	** NOTE TO SPECIFIER ** Delete if not required.
	3.6	FLOOR BOX INSTALLATION
		A.	Strictly comply with manufacturer's installation instructions and recommendations and approved shop drawings. Coordinate installation with adjacent work to ensure proper clearances and to prevent electrical hazards.
			1.	Mechanical Security: Raceway systems shall be mechanically continuous and connected to all electrical outlets, boxes, device mounting brackets, and cabinets, in accordance with manufacturer's installation sheets.
			2.	Electrical Security: Metal raceway shall be electrically continuous and bonded in accordance with the National Electric Code for proper grounding.
			3.	Raceway Support: Raceway shall be supported at intervals not exceeding 5 feet or in accordance with manufacturer's installation sheets.
			4.	Accessories: Provide accessories as required for a complete installation, including insulated bushings and inserts where required by manufacturer.
			5.	Unused Openings: Close unused raceway openings using manufacturer's recommended accessories.
		B.	Install floor boxes to permit all wiring to be completed at floor level.
	** NOTE TO SPECIFIER ** Delete if not required.
	3.7	FIRE STOP THRU-WALL/THRU-FLOOR FITTINGS INSTALLATION
		A.	Prior to and during installation, refer to the system layout or approval drawings containing all elements of the system. Installer shall comply with complete system instruction sheets.
		B.	The firestop device shall be installed in accordance with the UL Fire Resistance Directory, as well as any applicable codes and standards for general building, electrical and firestopping installation practices.
	3.8	PROTECTION
		A.	Protect installed products until completion of project.
		B.	Touch-up, repair or replace damaged products before Substantial Completion.
	END OF SECTION