Customize this spec with SpecWizard
Download SECTION 08 36 13 RESIDENTIAL SECTIONAL DOORS for
WORD | RTF | Text | Word Perfect
Find over 500 more CSI Sections
on Arcat.com
Switch to Masterformat 95
 
SECTION 08 36 13
RESIDENTIAL SECTIONAL DOORS
 
 
Copyright 2013 - 2017 ARCAT, Inc. - All rights reserved
** NOTE TO SPECIFIER ** Clopay Building Products Company; residential sectional doors.
This section is based on the products of Clopay Building Products Company, which is located at:
8585 Duke Blvd.
Mason, OH 45040-3101
Customer Service Toll Free: 800-225-6729
Corporate Offices Phone: 513-770-4800
Corporate Offices Fax: 513-770-3519
Email:cia@clopaydoor.com
Web Site: www.clopay.com
With two manufacturing facilities and 49 distribution centers across the U.S. and Canada, Clopay Building Products is North America's leading manufacturer of residential garage doors and a preferred supplier of commercial overhead sectional and rolling steel doors.
 
PART 1 GENERAL
 
1.1
SECTION INCLUDES
 
** NOTE TO SPECIFIER ** Delete types not required.
 
A.
Residential sectional doors of the following types:
1.
Full view aluminum doors. (Avante Collection)
2.
Steel sectional doors. (Classic Collection Premium Series)
3.
Steel sectional doors. (Classic Collection Value Plus Series)
4.
Steel sectional doors, non-insulated. (Classic Collection Value Series)
5.
Sectional doors. (Coachman Collection)
6.
Steel sectional doors. (Gallery Collection)
7.
Sectional doors. (Grand Harbor Collection)
8.
Sectional doors. (Canyon Ridge Collection)
9.
Steel sectional doors. (Modern Steel Collection)
1.2
RELATED SECTIONS
 
** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
 
A.
Section 05 50 00 - Metal Fabrications.
B.
Section 06 10 00 - Rough Carpentry.
C.
Section 08 71 53 - Security Door Hardware.
D.
Section 11 12 26.13 - Parking Fee Coin Collection Equipment.
E.
Division 16 - Electrical - Electrical service and connections for powered operators.
1.3
REFERENCES
 
** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
 
A.
ASTM International (ASTM):
1.
ASTM A 653 - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process.
2.
ASTM A 924 - Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process.
1.4
SUBMITTALS
A.
Submit under provisions of Section 01 30 00 - Administrative Requirements.
B.
Product Data: Manufacturer's data sheets and detail drawings for each product to be used, including:
1.
Preparation instructions and recommendations.
2.
Storage and handling requirements and recommendations.
3.
Installation details and methods.
4.
Operation and maintenance data.
 
** NOTE TO SPECIFIER ** Delete below if electrically operated doors not required.
 
5.
Nameplate data and ratings for motors.
C.
Shop Drawings: Include opening dimensions and required tolerances, connection details, anchorage spacing, hardware locations, and installation details.
 
** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.
 
D.
Selection Samples: Submit two complete sets of color chips representing manufacturer's full range of available colors and patterns.
E.
Verification Samples: For each finish product specified, submit samples that represent actual product, color, and sheen.
1.5
QUALITY ASSURANCE
A.
Manufacturer Qualifications: Company specializing in manufacturing the types of doors specified in this section, with not less than ten years of documented experience.
B.
Installer Qualifications: Company specializing in installing the types of products specified in this section, with minimum of two years of documented experience, and approved by the door manufacturer.
1.6
DELIVERY, STORAGE, AND HANDLING
A.
Deliver, store and handle materials and products in strict compliance with manufacturer's instructions and recommendations and industry standards.
B.
Store products indoors in manufacturer's or fabricator's original containers and packaging, with labels clearly identifying product name and manufacturer. Protect from damage.
1.7
PROJECT CONDITIONS
A.
Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install systems under environmental conditions outside manufacturer's recommended limits.
1.8
WARRANTY
A.
Finish Warranty:
 
** NOTE TO SPECIFIER ** Lifetime warranty period not available with all products. Consult manufacturer for details. Delete warranty periods not required.
 
1.
Warranty period: 5 years against cracking, checking and peeling. - All Residential Doors.
2.
Warranty period: 15 years against rust through. - All Value Residential Doors.
3.
Warranty period: 25 years against rust through. - All Value Plus Residential Doors.
4.
Warranty period: Lifetime against rust through. - All Premium Residential Doors.
 
** NOTE TO SPECIFIER ** Not applicable to all models. Delete if not required.
 
B.
Delamination Warranty: Provide manufacturer's standard warranty against delamination.
1.
Warranty period: 5 years.
C.
Hardware and Springs Warranty: Provide manufacturer's standard warranty against defects in materials or workmanship.
1.
Warranty period: 3 years.
 
** NOTE TO SPECIFIER ** Delete if not required.
 
D.
Warranty for Optional Windows: Provide manufacturer's standard warranty
 
** NOTE TO SPECIFIER ** Delete warranty period not required.
 
1.
Warranty period: 10 years against manufacturing defects and excessive discoloration of the optional windows.
2.
Warranty period: 3 years against defects in materials and workmanship of the optional windows.
PART 2 PRODUCTS
 
2.1
MANUFACTURERS
A.
Acceptable Manufacturer: Clopay Building Products Company, which is located at: 8585 Duke Blvd.; Mason, OH 45040; Toll Free Tel: 800-526-4301; Tel: 513-770-4800; Fax: 888-434-3193; Email: request info (arch@clopay.com); Web: www.clopaydoor.com/commercial/home
 
** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
 
B.
Substitutions: Not permitted.
C.
Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.
2.2
SECTIONAL OVERHEAD DOORS - GENERAL
A.
Wind Performance Requirements: As requested, design doors to withstand positive and negative wind loads as calculated in accordance with applicable building code. Doors tested to 1.5 times design wind load, according to ASTME330.
 
** NOTE TO SPECIFIER ** Fill in blanks below as applicable. If the two paragraphs below are retained, be careful not to specify specific doors that conflict with these requirements. Instead, select door types required and leave specific door thickness and gauge to manufacturer. Delete if not required.
 
1.
Design Wind Load: ________lb/sf (_____kPa).
 
** NOTE TO SPECIFIER ** Torsion spring counterbalance cannot be specified in conjunction with extension spring counterbalance. Delete counterbalance type not required.
 
B.
Counterbalance Type: Torsion spring counterbalance.
1.
Torsion spring counterbalance mechanism sized to weight of the door, with helically wound, coated oil tempered or galvanized torsion spring mounted on a steel shaft; cable drum of die cast aluminum with high strength galvanized aircraft cable with minimum 7 to 1 safety factor.
 
** NOTE TO SPECIFIER ** Delete spring type not required.
 
2.
Spring Type: Standard Cycle Spring, 10,000 cycle.
3.
Spring Type: Provide optional High Cycle Spring, 20,000 cycle.
 
** NOTE TO SPECIFIER ** The following is available for all models except Avante. Delete if not required.
 
C.
Counterbalance Type: Extension spring counterbalance.
1.
Extension spring counterbalance mechanism sized to weight of the door, with a black painted extension spring; cable sheaves of galvanized steel with high strength galvanized aircraft cable with minimum 7 to 1 safety factor. Standard high strength galvanized aircraft cable to contain spring in the event of spring failure; minimum 7 to 1 safety factor.
2.
Standard Cycle Spring: 10,000 cycle.
 
** NOTE TO SPECIFIER ** Delete if not required.
 
2.3
FULL VIEW ALUMINUM DOORS
A.
Full View Aluminum Doors: Clopay Avante Collections as manufactured by Clopay Building Products Company.
1.
Model AV - w/ 1/8 inch (3 mm) tempered glass.
2.
Model AVI- w/ Heavy Glazing (insulated or 1/4 inch (6 mm) tempered).
3.
Door Construction: 2.125 inch (54 mm) thick doors.
a.
Panel Sections: 2-1/8 inches (54 mm) thick extruded 6053-T5 aluminum, with integral reinforcing fin.
b.
Enclosed Top and Bottom Rails: 3-1/2 inches (89 mm) wide, meeting rails 2-13/16 inch (71.4 mm) wide, and end stiles 3-1/2 inches (89 mm) wide, with meeting rails meeting to form a tongue-and-groove joint and bottom rail configured to retain U-shaped flexible PVC astragal.
c.
Glazing and Solid Panels: Installed and sealed with hot melt sealant, locking retainer.
4.
Maximum Door Size AV: 20 ft 0 in (6.1 m) wide by 16 ft (4.9 m) high.
5.
Maximum Door Size AVI: 16 ft 2 in (5.0 m) wide by 16 ft (4.9 m) high.
 
** NOTE TO SPECIFIER ** Delete options for windows not required.
 
6.
Windows: None, doors come standard with no windows.
7.
Windows: Provide Full-view aluminum sections, pre-painted to match door.
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) clear tempered DSB glass.
b.
Glazing: 1/8 inch (3 mm) gray tinted tempered DSB glass.
c.
Glazing: 1/8 inch (3 mm) bronze tinted tempered DSB glass.
d.
Glazing: 1/8 inch (3 mm) obscure tempered DSB glass.
e.
Glazing: 1/8 inch (3 mm) frosted tempered DSB glass.
f.
Glazing: 1/8 inch (3 mm) frosted acrylic, special order.
g.
Glazing: 1/8 inch (3 mm) clear acrylic.
h.
Glazing: 1/8 inch (3 mm) gray acrylic, special order.
i.
Glazing: 1/8 inch (3 mm) white acrylic, special order.
j.
Glazing: 1/4 inch (6 mm) mirrored DSB glass, special order.
k.
Glazing: 1/4 inch (6 mm) white laminate DSB glass, special order.
l.
Glazing: 1/4 inch (6 mm) clear Polygal.
m.
Glazing: 1/4 inch (6 mm) bronze tinted Polygal, special order.
n.
Glazing: 1/2 inch (12 mm) clear tempered insulated DSB glass.
o.
Glazing: 1/2 inch (12 mm) obscure tempered insulated DSB glass.
p.
Glazing: 1/2 inch (12 mm) frosted tempered insulated DSB glass.
q.
Glazing: 1/2 inch (12 mm) low-e tempered insulated DSB glass.
r.
Glazing: Custom specialty glass ___.
s.
Glazing: None, no glazing, 0.050 inch (1.27 mm) aluminum panel.
 
** NOTE TO SPECIFIER ** Delete panel finishes not required.
 
1)
Panel Finish: Clear anodizing.
2)
Panel Finish: Black anodizing.
3)
Panel Finish: Bronze anodizing.
4)
Panel Finish: Standard White.
5)
Panel Finish: Dark Bronze anodizing
6)
Panel Finish: Chocolate painted.
7)
Panel Finish: Bronze painted
8)
Panel Finish: Ultra-Grain Cherry Light Finish simulated woodgrain paint finish.
9)
Panel Finish: Ultra-Grain Cherry Dark Finish simulated woodgrain paint finish.
10)
Panel Finish: Custom Color RAL Powder Coat _____________.
11)
Panel Finish: Clopay Color Blast Finish ________.
 
** NOTE TO SPECIFIER ** Paragraphs below are standard finish options; consult factory for other available custom finishes. Delete aluminum finishes not required;
 
8.
Aluminum Finish: Standard White painted.
9.
Aluminum Finish: Bronze painted.
10.
Aluminum Finish: Chocolate brown painted.
11.
Aluminum Finish: Clear Aluminum anodized.
12.
Aluminum Finish: Black anodized.
13.
Aluminum Finish: Bronze anodized.
14.
Aluminum Finish: Dark Bronze anodized.
15.
Aluminum Finish: Ultra-Grain Cherry Light Finish simulated woodgrain paint finish.
16.
Aluminum Finish: Ultra-Grain Cherry Dark Finish simulated woodgrain paint finish.
17.
Aluminum Finish: Custom Color RAL Powder Coat ______.
18.
Aluminum Finish: Clopay Color Blast Finish _____.
 
** NOTE TO SPECIFIER ** Delete locking type not required.
 
19.
Locking: 1 inside spring loaded slide bolt lock on end stile that engages slot in track.
20.
Locking: 2 inside spring loaded slide bolt locks on end stile that engage slots in track.
21.
Weatherstripping: Standard, provide U shaped bottom seal.
 
** NOTE TO SPECIFIER ** Perimeter seals are optional, choose from manufacturers standard options. Delete if not required.
 
22.
Perimeter Seals: _____.
23.
Tracks: Vertical tracks minimum 0.061 inch (1.55 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.075 inch (1.91 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required.
a.
Track Width: 2 inches (50 mm).
 
** NOTE TO SPECIFIER ** Delete track type not required.
 
b.
Provide standard lift tracks with 15 inches (381 mm) radius track as indicated.
c.
Provide vertical lift tracks as indicated.
d.
Provide high lift tracks as indicated.
e.
Provide tracks that follow roof slope tracks as indicated.
f.
Provide low headroom tracks as indicated.
2.4
RESIDENTIAL STEEL SECTIONAL DOORS - Premium (3-layer) Doors
A.
Residential Steel Sectional Doors: Classic Collection Premium Series as manufactured by Clopay Building Products Company
1.
Expanded Polystyrene (EPS) Insulated 1-3/8" (35mm) thick product :
 
** NOTE TO SPECIFIER ** Delete models not required.
 
a.
Short Panel Model: Clopay Model 4050.
b.
Long Panel Model: Clopay Model 4053.
2.
Expanded Polystyrene (EPS) Insulated 2 inches (51mm) thick product:
a.
Short Panel Model: Clopay Model 4300.
b.
Long Panel Model: Clopay Model 4310.
3.
Thermally-Broken, Intellicore Polyurethane insulated 1-3/8" (35mm) thick product:
 
** NOTE TO SPECIFIER ** Delete models not required.
 
a.
Short Panel Model: Clopay Model 9130.
b.
Long Panel Model: Clopay Model 9133.
4.
Thermally-Broken, Intellicore Polyurethane insulated 2 inches (51mm) thick product:
a.
Short Panel Model: Clopay Model 9200.
b.
Long Panel Model: Clopay Model 9203.
5.
Door Construction:
 
** NOTE TO SPECIFIER ** First option applies to models 4050, 4053, 4300, and 4310. Second option applies to models 9130, 9133, 9200 and 9203. Delete section not required.
 
a.
Sections (EPS): Pressure bonded expanded polystyrene (EPS) core construction between exterior and interior steel skins.
b.
Sections (Intellicore): Foamed in place Intellicore Polyurethane core construction between exterior and interior steel skins.
 
** NOTE TO SPECIFIER ** First option applies to models 4050, 4300, 9130 and 9200. Second option applies to models 4053, 4310, 9133 and 9203. Delete exterior steel skins not required.
 
c.
Exterior Steel Skins (Short Elegant Panel): Formed from Short Elegant Panel embossed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
d.
Exterior Steel Skins (Long Elegant Panel): Formed from flush Long Elegant Panel embossed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
e.
Interior Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
 
** NOTE TO SPECIFIER ** First option applies to models 4050 and 4053. Second option applies to models 4300, 4310, 9130, 9133, 9200 and 9203. Delete section joints not required.
 
f.
1 -3/8" EPS Section Joints: Sections formed to create tongue-in-groove meeting joint.
g.
Other Section Joints: Sections formed to create tongue-in-groove meeting joint with thermal break.
h.
Door Stiles: Galvanized steel end stiles and center stiles, pre-punched for easy hinge attachment.
i.
Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment.
j.
Connections: Stiles fastened to steel skins using Tog-L-Loc system.
k.
Handles: 2 High impact polymer step plate/lift handles to comply with DASMA 116 and be color-matched to the door sections.
 
** NOTE TO SPECIFIER ** First option applies to models 4050, 4053, 9130 and 9133. Second option applies to models 4300, 4310, 9200, and 9203. Delete maximum door size not required.
 
6.
Maximum Door Size 1-3/8 inch Thick Product: 18 ft 2 in (5.5 m) wide by 16 ft (4.9 m) high.
7.
Maximum Door Size 2 inches Thick Product: 20 ft 2 in (6.1 m) wide by 16 ft (4.9 m) high.
8.
Overall Panel Thickness listed in description
9.
Steel Skin Thickness:
 
** NOTE TO SPECIFIER ** Second option applies to color Black and all Ultra-Grain Finish options Delete option not required.
 
a.
Exterior: Minimum 27 gauge 0.016 inch (0.40 mm).
b.
Exterior: Minimum 24 gauge 0.022 inch (0.55 mm).
 
** NOTE TO SPECIFIER ** First option applies to models 9130, 9133, 9200 and 9203. Second option applies to models 4050, 4053, 4300 and 4310. Delete option for interior not required.
 
c.
Interior: Minimum 29 gauge 0.012 inch (0.30 mm). - Intellicore Doors
d.
Interior: Minimum 27 gauge 0.015 inch (0.38 mm). - EPS Doors
10.
End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 20 gauge, 0.034 inch (0.86 mm) thick.
11.
Bottom Section: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with U-shaped flexible PVC astragal.
12.
Thermal Resistance: Calculated in accordance with DASMA TDS-163.
 
** NOTE TO SPECIFIER ** First option applies to models 4050 and 4053. Second option applies to models 4300 and 4310. Third option applies to model 9130 and 9133. Fourth option applies to 9200and 9203. Delete options not required.
 
a.
EPS 1-3/8 inch (35mm) Thick - R-Value: 6.5 (deg F hr sq ft/Btu.)
b.
EPS 2 inch (51mm) Thick - R-Value: 9.0 (deg F hr sq ft/Btu.)
c.
Intellicore 1-3/8 inch (35mm) Thick - R-Value: 12.9 (deg F hr sq ft/Btu.)
d.
Intellicore 2 inch (51mm) Thick - R-Value: 18.4 (deg F hr sq ft/Btu.)
 
** NOTE TO SPECIFIER ** Delete options for windows not required.
 
13.
Windows: None, doors come standard with no windows.
 
** NOTE TO SPECIFIER ** Windows below available with Models 4050, 4300, 9130 and 9200. Delete if not required.
 
14.
Optional Windows: Provide optional Decorative Insert Short Panel Windows; injection molded ASA plastic windows measuring 19-1/2 inches x 12 inches (495 mm x 305 mm).
a.
Glazing: 3/32 inch (2.5 mm) clear SSB glass.
b.
Glazing: 1/8 inch (3 mm) clear DSB glass.
c.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
d.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
e.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
f.
Glazing: 1/8 inch (3 mm) clear acrylic.
g.
Glazing: 1/8 inch (3 mm) Frosted glass.
h.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
i.
Glazing: 1/8 inch (3 mm) Rain glass.
j.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
k.
Glazing: 1/8 inch (3 mm) Seeded glass.
l.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
 
** NOTE TO SPECIFIER ** Delete options for decorative snap-in plastic inserts not required.
 
m.
Decorative Snap-in Plastic Inserts: Sunset 501.
n.
Decorative Snap-in Plastic Inserts: Sunset 502.
o.
Decorative Snap-in Plastic Inserts: Sunset 503.
p.
Decorative Snap-in Plastic Inserts: Sunset 504.
q.
Decorative Snap-in Plastic Inserts: Sunset 505.
r.
Decorative Snap-in Plastic Inserts: Sunset 506.
s.
Decorative Snap-in Plastic Inserts: Charleston 508.
t.
Decorative Snap-in Plastic Inserts: Colonial 509.
u.
Decorative Snap-in Plastic Inserts: Prairie 510.
 
** NOTE TO SPECIFIER ** Delete if not required.
 
15.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows; woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb. impact as per the Florida Building Code) measuring 19-1/2 inches x 12 inches (495 mm x 305 mm).
a.
Glazing: Clear Polycarbonate.
 
** NOTE TO SPECIFIER ** Delete options for decorative snap-in plastic inserts not required.
 
b.
Decorative Snap-in Plastic Inserts: Sunset 501.
c.
Decorative Snap-in Plastic Inserts: Sunset 502.
d.
Decorative Snap-in Plastic Inserts: Sunset 503.
e.
Decorative Snap-in Plastic Inserts: Sunset 504.
f.
Decorative Snap-in Plastic Inserts: Sunset 505.
g.
Decorative Snap-in Plastic Inserts: Sunset 506.
h.
Decorative Snap-in Plastic Inserts: Charleston 508.
i.
Decorative Snap-in Plastic Inserts: Colonial 509.
j.
Decorative Snap-in Plastic Inserts: Prairie 510.
 
** NOTE TO SPECIFIER ** Windows below available with Models 4050, 4300, 9130 and 9200. Delete if not required.
 
16.
Windows: Provide optional Decorative Wrought Iron Series and Leaded Series Short Panel Windows; injection molded ASA plastic windows measuring 19-1/2 inches x 12 inches (495 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) Carlisle Short, frosted DSB glass, leaded-look.
b.
Glazing: 1/8 inch (3 mm) Kristin Short, frosted DSB glass, leaded-look.
c.
Glazing: 1/8 inch (3 mm) Roselle Short, frosted DSB glass, leaded-look.
d.
Glazing: 1/8 inch (3 mm) Trenton Short, frosted DSB glass, leaded-look.
e.
Glazing: 1/2 inch (12 mm) Carlisle Short, frosted insulated DSB glass, leaded-look.
f.
Glazing: 1/2 inch (12 mm) Kristin Short, frosted insulated DSB glass, leaded-look.
g.
Glazing: 1/2 inch (12 mm) Roselle Short, frosted insulated DSB glass, leaded-look.
h.
Glazing: 1/2 inch (12 mm) Trenton Short, frosted insulated DSB glass, leaded-look.
i.
Glazing: Tuscany Short wrought iron acrylic.
j.
Glazing: Orleans Short wrought iron acrylic.
 
** NOTE TO SPECIFIER ** Windows below available with Models 4050, 4053, 4300, 4310, 9130, 9133, 9200, and 9203. Delete if not required.
 
17.
Windows: Provide optional Decorative Insert Long Panel Windows; injection molded ASA plastic windows measuring 40-1/2 inches x 12 inches (1029 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 3/32 inch (2.5 mm) clear SSB glass.
b.
Glazing: 1/8 inch (3 mm) clear DSB glass.
c.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
d.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
e.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
f.
Glazing: 1/8 inch (3 mm) clear acrylic.
g.
Glazing: 1/8 inch (3 mm) Frosted glass.
h.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
i.
Glazing: 1/8 inch (3 mm) Rain glass.
j.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
k.
Glazing: 1/8 inch (3 mm) Seeded glass.
l.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
 
** NOTE TO SPECIFIER ** Delete options for decorative snap-in plastic inserts not required.
 
m.
Decorative Snap-in Plastic Inserts: Sunset 601.
n.
Decorative Snap-in Plastic Inserts: Sunset 603.
o.
Decorative Snap-in Plastic Inserts: Sunset 605.
p.
Decorative Snap-in Plastic Inserts: Charleston 608.
q.
Decorative Snap-in Plastic Inserts: Prairie 610.
r.
Decorative Snap-in Plastic Inserts: Madison 611.
s.
Decorative Snap-in Plastic Inserts: Stockton 612.
t.
Decorative Snap-in Plastic Inserts: Madison Arch 613.
 
** NOTE TO SPECIFIER ** Windows below available with Models 4050, 4053, 4300, 9130, 9133, 9200 and 9203. Delete if not required.
 
18.
Windows: Provide optional Decorative Wrought Iron Series and Leaded Series Long Panel Windows; injection molded ASA plastic windows measuring 40-1/2 inches x 12 inches (1029 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) Carlisle Long, frosted DSB glass, leaded-look.
b.
Glazing: 1/8 inch (3 mm) Kristin Long, frosted DSB glass, leaded-look.
c.
Glazing: 1/8 inch (3 mm) Roselle Long, frosted DSB glass, leaded-look.
d.
Glazing: 1/8 inch (3 mm) Trenton Long, frosted DSB glass, leaded-look.
e.
Glazing: 1/2 inch (12 mm) Carlisle Long, frosted insulated DSB glass, leaded-look.
f.
Glazing: 1/2 inch (12 mm) Kristin Long, frosted insulated DSB glass, leaded-look.
g.
Glazing: 1/2 inch (12 mm) Roselle Long, frosted insulated DSB glass, leaded-look.
h.
Glazing: 1/2 inch (12 mm) Trenton Long, frosted insulated DSB glass, leaded-look.
i.
Glazing: Tuscany Long wrought iron acrylic.
j.
Glazing: Orleans Long wrought iron acrylic.
 
** NOTE TO SPECIFIER ** Windows below available with Models 9130, 9133, 9200 and 9203. Delete if not required.
 
19.
Windows: Provide optional Architectural Series Short Windows; extruded cellular PVC windows measuring 19-1/2 inches x 16 inches (495 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Grilles only available with first four glazing options. Delete if not required.
 
a.
Grilles: Short with square grilles, SQ22.
b.
Grilles: Short with rectangular grilles, REC11.
c.
Grilles: Plain Short, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Rain glass.
k.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
l.
Glazing: 1/8 inch (3 mm) Seeded glass.
m.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
n.
Glazing: 1/8 inch (3 mm) Kristin Short, frosted DSB glass, leaded-look.
o.
Glazing: 1/8 inch (3 mm) Trenton Short, frosted DSB glass, leaded-look.
p.
Glazing: 1/8 inch (3 mm) Clayton Short, frosted DSB glass, leaded-look.
q.
Glazing: 1/2 inch (12 mm) Kristin Short, frosted insulated DSB glass, leaded-look.
r.
Glazing: 1/2 inch (12 mm) Trenton Short, frosted insulated DSB glass, leaded-look.
s.
Glazing: 1/2 inch (12 mm) Clayton Short, frosted insulated DSB glass, leaded-look.
t.
Glazing: Wrought iron Short, acrylic.
 
** NOTE TO SPECIFIER ** Windows below available with Models 9130, 9133, 9200 and 9203. Delete if not required.
 
20.
Windows: Provide optional Architectural Series Long Windows; extruded cellular PVC windows measuring 42 inches x 16 inches (1067 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Grilles only available with first four glazing options. Delete if not required.
 
a.
Grilles: Long with square grilles, SQ24.
b.
Grilles: Long with rectangular grilles, REC14.
c.
Grilles: Plain Long, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Rain glass.
k.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
l.
Glazing: 1/8 inch (3 mm) Seeded glass.
m.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
n.
Glazing: 1/8 inch (3 mm) Kristin Long, frosted DSB glass, leaded-look.
o.
Glazing: 1/8 inch (3 mm) Trenton Long, frosted DSB glass, leaded-look.
p.
Glazing: 1/8 inch (3 mm) Clayton Long, frosted DSB glass, leaded-look.
q.
Glazing: 1/2 inch (12 mm) Kristin Long, frosted insulated DSB glass, leaded-look.
r.
Glazing: 1/2 inch (12 mm) Trenton Long, frosted insulated DSB glass, leaded-look.
s.
Glazing: 1/2 inch (12 mm) Clayton Long, frosted insulated DSB glass, leaded-look.
t.
Glazing: Wrought Iron Long, acrylic.
21.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows, woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb impact as per the Florida Building Code) measuring 19-12 inches x 16 inches (495 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Delete glazing options not required.
 
a.
Glazing: Clear polycarbonate.
b.
Glazing: Matte polycarbonate.
c.
Glazing: Bronze polycarbonate.
d.
Glazing: Pebbled polycarbonate.
e.
Grilles: Long with square grilles, SQ22.
f.
Grilles: Plain Short, no grilles.
22.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows, woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb impact as per the Florida Building Code) measuring 42 inches x 16 inches (1067 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Delete glazing options not required.
 
a.
Glazing: Clear polycarbonate.
b.
Glazing: Matte polycarbonate.
c.
Glazing: Bronze polycarbonate.
d.
Glazing: Pebbled polycarbonate
e.
Grilles: Long with square grilles, SQ24.
f.
Grilles: Plain Long, no grilles.
 
** NOTE TO SPECIFIER ** Windows below available with Models 9130, 9133, 9200 and 9203. Delete if not required.
 
23.
Windows: Provide optional Architectural Series ARCH1 Windows; extruded cellular PVC windows measuring 42 inches x 16 inches (1067 mm x 406 mm) with a 159-1/2 inches (4051 mm) radius top.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) clear DSB glass.
b.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
c.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
d.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
e.
Glazing: 1/8 inch (3 mm) Frosted glass.
f.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
g.
Glazing: 1/8 inch (3 mm) Rain glass.
h.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
i.
Glazing: 1/8 inch (3 mm) Seeded glass.
j.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
 
** NOTE TO SPECIFIER ** Delete grilles not required.
 
k.
Grilles: Snap-in plastic grilles.
l.
Grilles: Vertical grilles.
m.
Grilles: Plain, no grilles.
 
** NOTE TO SPECIFIER ** Windows below available with Models 9130, 9133, 9200 and 9203. Delete if not required.
 
24.
Windows: Provide optional Architectural Series ARCH2 Windows; extruded cellular PVC windows measuring 42 inches x 16 inches (1067 mm x 406 mm) with a 39-3/4 inches (1001 mm) radius top.
 
** NOTE TO SPECIFIER ** Delete grilles not required.
 
a.
Grilles: Snap-in plastic grilles.
b.
Grilles: Vertical grilles.
c.
Grilles: Plain, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Rain glass.
k.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
l.
Glazing: 1/8 inch (3 mm) Seeded glass.
m.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
n.
Glazing: Wrought Iron ARCH, acrylic.
 
** NOTE TO SPECIFIER ** First option below applies only to Models 4050, 4053, 4300 and 4310. Second option below applies only to Models 9130, 9133, 9200 and 9203. Delete interior finish not required.
 
25.
Interior Finish (EPS) Door- Stucco embossed texture with flush design, white interior color.
26.
Interior Finish (Intellicore) Door- Stucco embossed texture with shallow U ribbed pattern.
27.
Exterior Finishes:
 
** NOTE TO SPECIFIER ** First option available with Model 4050, 4300, 9130 and 9200. Second option available with Model 4053, 4310, 9133 and 9203. Delete finishes not required.
 
a.
Finish Type: Woodgrain embossed texture, Short Elegant Panel embossments.
b.
Finish Type: Woodgrain embossed texture, Long Elegant Panel embossments.
 
** NOTE TO SPECIFIER ** Models 4050 and 4053 only available in first 8 options. Delete colors not required.
 
c.
Color: Standard White.
d.
Color: Almond.
e.
Color: Desert Tan.
f.
Color: Sandtone.
g.
Color: Chocolate.
h.
Color: Bronze.
i.
Color: Hunter Green.
j.
Color: Gray.
k.
Color: Glacier White.
l.
Color: Mocha Brown.
m.
Color: Black.
n.
Color: Clopay Color Blast ____.
28.
Ultra-Grain Exterior Finish:
 
** NOTE TO SPECIFIER ** First option available with Model 4300 and 9200. Second option available with Model 4310 and 9203. Options not available on Models 9130 and 9133. Delete if not required.
 
a.
Finish Type: Ultra-Grain Exterior Finish Stucco embossed texture with Short Elegant Panel embossments to simulate the look of stained wood.
b.
Finish Type: Ultra-Grain Exterior Finish: Stucco embossed texture with Long Elegant Panel embossments in one of the following color options to simulate the look of stained wood.
 
** NOTE TO SPECIFIER ** Options not available on Models 9130 and 9133. Delete finish not required.
 
c.
Finish: Ultra-Grain Classic Medium Finish.
d.
Finish: Ultra-Grain Classic Cherry Finish.
e.
Finish: Ultra-Grain Classic Walnut Finish.
 
** NOTE TO SPECIFIER ** Delete locking types not required.
 
29.
Locking: Standard, keyed spring-loaded lock bar.
30.
Locking: Provide optional keyed spring-loaded snap latches.
31.
Locking: Provide optional non-keyed interior slide bolt.
32.
Weatherstripping: Standard, Provide U shaped bottom seal.
 
** NOTE TO SPECIFIER ** Perimeter seals are optional, choose from manufacturers standard options. Delete if not required.
 
33.
Perimeter Seals: _____.
34.
Tracks: Vertical tracks minimum 0.040 inch (1.02 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.051 inch (1.29 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required.
 
** NOTE TO SPECIFIER ** Delete track type not required.
 
a.
Track Type: Provide standard lift tracks.
b.
Track Type: Provide optional low headroom track.
c.
Track Type: Provide optional high lift track.
d.
Track Type: Provide optional follow-the-roof track.
e.
Track Width: 2 inches (50 mm).
 
** NOTE TO SPECIFIER ** 20 inch and 32 inch radius only available on doors up to 12 ft high. Delete track radius not required.
 
f.
Track Radius: 10 inch (254 mm).
g.
Track Radius: 12 inch (305 mm).
h.
Track Radius: 15 inch (381 mm).
i.
Track Radius: 20 inch (508 mm).
j.
Track Radius: 32 inch (813 mm).
2.5
RESIDENTIAL STEEL SECTIONAL DOORS - Value Plus (2-layer) Doors
A.
Residential Steel Sectional Doors: Classic Collection Value Plus Series as manufactured by Clopay Building Products Company.
 
** NOTE TO SPECIFIER ** Delete models not required.
 
1.
Clopay Model 1500: 25 Ga. Ship-Lap Joint Short Panel, 1-5/16 insulated Model:
2.
Clopay Model 76V: 25 Ga. Ship-Lap Joint Long Panel 1-5/16 insulated Model
3.
Clopay Model T41S: 24 Ga. Tongue and Groove Joint Short Panel 7/8" insulated Model:
4.
Clopay Model T41L: 24 Ga. Tongue and Groove Joint Long Panel 7/8" insulated Model
5.
Clopay Model T42S: 24 Ga. Tongue and Groove Joint Short Panel 1-5/16" insulated Model
6.
Clopay Model T42L: 24 Ga. Tongue and Groove Joint Long Panel 1-5/16" insulated Model:
7.
Clopay Model T51S: 25 Ga. Tongue and Groove Joint Short Panel 7/8" insulated Model:
8.
Clopay Model T51L: 25 Ga. Tongue and Groove Joint Long Panel 7/8" insulated Model
9.
Clopay Model T52S: 25 Ga. Tongue and Groove Joint Short Panel 1-5/16" insulated Model
10.
Clopay Model T52L: 25 Ga. Tongue and Groove Joint Long Panel 1-5/16" insulated Model
11.
Insulation: Polystyrene Insulated.
12.
Door Construction:
 
** NOTE TO SPECIFIER ** First option applies to Models 1500, 76V, T42S and T42L. Second option applies to Models T41S, T41L, T51S and T51L. Delete section not required.
 
a.
Sections: Steel frame and skin construction with 1-5/16 inch (33 mm) thick polystyrene insulation with vinyl backer.
b.
Sections: Steel frame and skin construction with bonded 7/8 inch (22 mm) thick polystyrene insulation with vinyl backer.
 
** NOTE TO SPECIFIER ** First option applies to Models 1500, T41S, T42S, T51S and T52S. Second option applies to Model 76V, T41L, T42L, T51L and T52L. Delete steel skins not required.
 
c.
Steel Skins: Formed from Short Traditional Panel embossed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
d.
Steel Skins: Formed from Long Traditional Panel embossed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
 
** NOTE TO SPECIFIER ** First option applies to Models 1500 and 76V. Second option applies to Models T41S, T41L, T42S, T42L, T51S, T51L, T52S and T52L. Delete section joints not required.
 
e.
Section Joints: Sections formed to create shiplap meeting joint.
f.
Section Joints: Sections formed to create tongue and groove meeting joint.
g.
Door Stiles: Galvanized steel end stiles and center stiles, pre-punched for easy hinge attachment.
h.
Connections: Stiles fastened to steel skins using Tog-L-Loc system.
i.
Handles: 2 high impact polymer step plate/lift handles to comply with DASMA 116 and be color-matched to the door sections.
 
** NOTE TO SPECIFIER ** First option applies to Models 1500, 76V, T41S, T41L, T51S, T51L, T52S and T52L. Second option applies to Models T42S and T42L. Delete maximum door size not required.
 
13.
24 Ga Models Maximum Door Size: 18 ft (5.5 m) wide by 16 ft (4.9 m) high.5
14.
25 Ga Models Maximum Door Size: 20 ft (6.1 m) wide by 16 ft (4.9 m) high.
 
** NOTE TO SPECIFIER ** First option applies to Models 1500 and 76V. Second option applies to Models T41S, T41L, T42S, T42L, T51S, T51L, T52S and T52L. Delete overall panel thickness not required.
 
15.
Overall Panel Thickness: 2.125 inches (54 mm).
16.
Overall Panel Thickness: 2 inches (51 mm).
 
** NOTE TO SPECIFIER ** First option applies to Models 1500, 76V, T52S and T52L. Second option applies to Models T41S, T41L, T42S and T42L. Delete steel skins not required.
 
17.
Steel Skin Thickness: Minimum 25 gauge 0.019 inch (0.48 mm)
18.
Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm)
19.
End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.049 inch (1.25 mm) thick.
 
** NOTE TO SPECIFIER ** First option applies to Models 1500 and 76V. Second option applies to Models T41S, T41L, T42S, T42L, T51S, T51L, T52S and T52L. Delete bottom section not required.
 
20.
Bottom Section: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with bulb-shaped flexible PVC astragal.
21.
Bottom Section: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with U-shaped flexible PVC astragal.
22.
Thermal Resistance: Calculated in accordance with DASMA TDS-163
 
** NOTE TO SPECIFIER ** First option applies to Models 1500, 76V, T42S and T42L. Second option applies to Models T41S, T41L, T51S and T51L. Delete option not required.
 
a.
R-Value: 6.3 deg F hr sq ft/Btu.
b.
R-Value: 4.4 deg F hr sq ft/Btu.
 
** NOTE TO SPECIFIER ** Delete options for windows not required.
 
23.
Windows: None, doors come standard with no windows.
 
** NOTE TO SPECIFIER ** Windows below available with Model 1500, T41S, T42S, T51S and T52S. Delete if not required.
 
24.
Windows: Provide optional Decorative Insert Series Short Panel Windows; injection molded ASA plastic windows measuring 19-1/2 inches x 12 inches (495 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 3/32 inch (2.5 mm) clear SSB glass.
b.
Glazing: 1/8 inch (3 mm) clear DSB glass.
c.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
d.
Glazing: 1/8 inch (3 mm) Clear acrylic.
e.
Glazing: 1/8 inch (3 mm) Frosted glass.
f.
Glazing: 1/8 inch (3 mm) Rain glass.
g.
Glazing: 1/8 inch (3 mm) Seeded glass.
 
** NOTE TO SPECIFIER ** Delete options for decorative snap-in plastic inserts not required.
 
h.
Decorative Snap-in Plastic Inserts: Sunset 501.
i.
Decorative Snap-in Plastic Inserts: Sunset 502.
j.
Decorative Snap-in Plastic Inserts: Sunset 503.
k.
Decorative Snap-in Plastic Inserts: Sunset 504.
l.
Decorative Snap-in Plastic Inserts: Sunset 505.
m.
Decorative Snap-in Plastic Inserts: Sunset 506.
n.
Decorative Snap-in Plastic Inserts: Charleston 508.
o.
Decorative Snap-in Plastic Inserts: Colonial 509.
p.
Decorative Snap-in Plastic Inserts: Prairie 510.
 
** NOTE TO SPECIFIER ** Windows below available with Model 1500, T41S, T42S, T51S and T52S. Delete if not required.
 
25.
Windows: Provide optional Decorative Short Panel Windows; injection molded ASA plastic windows measuring 19-1/2 inches x 12 inches (495 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) Carlisle Short, frosted DSB glass, leaded-look.
b.
Glazing: 1/8 inch (3 mm) Kristin Short, frosted DSB glass, leaded-look.
c.
Glazing: 1/8 inch (3 mm) Roselle Short, frosted DSB glass, leaded-look.
d.
Glazing: 1/8 inch (3 mm) Trenton Short, frosted DSB glass, leaded-look.
e.
Glazing: Tuscany Short wrought iron acrylic.
f.
Glazing: Orleans Short wrought iron acrylic.
26.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows; woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb. impact as per the Florida Building Code) measuring 19-1/2 inches x 12 inches (495 mm x 305 mm).
a.
Glazing: Clear Polycarbonate.
 
** NOTE TO SPECIFIER ** Delete decorative snap-in plastic inserts not required.
 
b.
Decorative Snap-in Plastic Inserts: Sunset 501.
c.
Decorative Snap-in Plastic Inserts: Sunset 502.
d.
Decorative Snap-in Plastic Inserts: Sunset 503.
e.
Decorative Snap-in Plastic Inserts: Sunset 504.
f.
Decorative Snap-in Plastic Inserts: Sunset 505.
g.
Decorative Snap-in Plastic Inserts: Sunset 506.
h.
Decorative Snap-in Plastic Inserts: Charleston 508.
i.
Decorative Snap-in Plastic Inserts: Colonial 509.
j.
Decorative Snap-in Plastic Inserts: Prairie 510.
 
** NOTE TO SPECIFIER ** Windows below available with Model 1500, 76V, T41S, T41L, T42S, T42L, T51S, T51L, T52S and T52L. Delete if not required.
 
27.
Windows: Provide optional Decorative Insert Series Long Panel Windows; injection molded ASA plastic windows measuring 40-1/2 inches x 12 inches (1029 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 3/32 inch (2.5 mm) clear SSB glass.
b.
Glazing: 1/8 inch (3 mm) clear DSB glass.
c.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
d.
Glazing: 1/8 inch (3 mm) Clear acrylic.
e.
Glazing: 1/8 inch (3 mm) Frosted glass.
f.
Glazing: 1/8 inch (3 mm) Rain glass.
g.
Glazing: 1/8 inch (3 mm) Seeded glass.
 
** NOTE TO SPECIFIER ** Delete options for decorative snap-in plastic inserts not required.
 
h.
Decorative Snap-in Plastic Inserts: Sunset 601.
i.
Decorative Snap-in Plastic Inserts: Sunset 603.
j.
Decorative Snap-in Plastic Inserts: Sunset 605.
k.
Decorative Snap-in Plastic Inserts: Charleston 608.
l.
Decorative Snap-in Plastic Inserts: Prairie 610.
m.
Decorative Snap-in Plastic Inserts: Madison 611.
n.
Decorative Snap-in Plastic Inserts: Stockton 612.
o.
Decorative Snap-in Plastic Inserts: Madison Arch 613.
 
** NOTE TO SPECIFIER ** Windows below available with Model 1500, 76V, T41S, T41L, T42S, T42L, T51S, T51L, T52S and T52L. Delete if not required.
 
28.
Windows: Provide optional Decorative Long Panel Windows; injection molded ASA plastic windows measuring 40-1/2 inches x 12 inches (1029 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) Carlisle Long, frosted DSB glass, leaded-look.
b.
Glazing: 1/8 inch (3 mm) Kristin Long, frosted DSB glass, leaded-look.
c.
Glazing: 1/8 inch (3 mm) Roselle Long, frosted DSB glass, leaded-look.
d.
Glazing: 1/8 inch (3 mm) Trenton Long, frosted DSB glass, leaded-look.
e.
Glazing: Tuscany Long wrought iron acrylic.
f.
Glazing: Orleans Long wrought iron acrylic.
29.
Interior Finish: Vinyl backer over expanded polystyrene (EPS) insulation.
30.
Exterior Finish:
 
** NOTE TO SPECIFIER ** First option below applies to Model 1500 and T52S. Second option applies to Model 76V and T52L. Delete option for exterior finish not required.
 
a.
Finish Type: Woodgrain embossed texture, Short Traditional Panel embossments.
b.
Finish Type: Woodgrain embossed texture with Long Traditional Panel embossments.
 
** NOTE TO SPECIFIER ** Delete options for color not required.
 
c.
Color: Standard White.
d.
Color: Almond.
e.
Color: Desert Tan.
f.
Color: Sandtone.
g.
Color: Chocolate.
 
** NOTE TO SPECIFIER ** Delete locking types not required.
 
31.
Locking: Standard, keyed spring-loaded lock bar.
32.
Locking: Provide optional keyed spring-loaded snap latches.
33.
Locking: Provide optional non-keyed interior slide bolt.
34.
Weatherstripping: Standard, Provide U-shaped bottom seal.
 
** NOTE TO SPECIFIER ** Perimeter seals are optional, choose from manufacturers standard options. Delete if not required.
 
35.
Perimeter Seals: _____.
36.
Tracks: Vertical tracks minimum 0.040 inch (1.02 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.051 inch (1.29 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required.
 
** NOTE TO SPECIFIER ** Delete track type not required.
 
a.
Track Type: Provide standard lift tracks.
b.
Track Type: Provide optional low headroom track.
c.
Track Type: Provide optional high lift track.
d.
Track Type: Provide optional follow-the-roof track.
e.
Track Width: 2 inches (50 mm).
 
** NOTE TO SPECIFIER ** 20 inch and 32 inch radius only available on doors up to 12 ft high. Delete track radius not required.
 
f.
Track Radius: 10 inch (254 mm).
g.
Track Radius: 12 inch (305 mm).
h.
Track Radius: 15 inch (381 mm).
i.
Track Radius: 20 inch (508 mm).
j.
Track Radius: 32 inch (813 mm).
2.6
RESIDENTIAL STEEL SECTIONAL DOORS, NON-INSULATED - Value Series
A.
Residential Steel Sectional Doors: Classic Collection Value Series as manufactured by Clopay Building Products Company.
 
** NOTE TO SPECIFIER ** Delete if not required.
 
1.
Clopay Model 73: 25 Ga. Ship-Lap Joint Model Short Panel.
2.
Clopay Model 76: 25 Ga. Ship-Lap Joint Long Panel Model.
3.
Clopay Model 94: 24 Ga. Ship-Lap Joint Short Panel Model.
4.
Clopay Model T40S: 24 Ga. Tongue and Groove Joint Short Panel Model.
5.
Clopay Model T40L: 24 Ga. Tongue and Groove Joint Long Panel Model.
6.
Clopay Model T50S: 25 Ga. Tongue and Groove Joint Short Panel Model.
7.
Clopay Model T50L: 25 Ga. Tongue and Groove Joint Long Panel Model.
8.
Door Construction:
a.
Sections: Steel frame and skin construction.
 
** NOTE TO SPECIFIER ** First option applies to Model 73, 94, T40S, T50S. Second option applies to Model 76, T40L, T50L. Delete if not required.
 
b.
Steel Skins: Formed from Short Traditional Panel embossed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
c.
Steel Skins: Formed from Long Traditional Panel embossed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
 
** NOTE TO SPECIFIER ** Option below applies to Model T40L. Delete if not required.
 
d.
Section Joints: Sections formed to create tongue and groove meeting joint.
e.
Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment.
f.
Door Stiles: Galvanized steel end stiles and center stiles, pre-punched for easy hinge attachment.
g.
Connections: Stiles fastened to steel skins using Tog-L-Loc system.
h.
Handles: 2 High impact polymer step plate/lift handles to comply with DASMA 116 and be color-matched to the door sections.
 
** NOTE TO SPECIFIER ** First option applies to Models 73 and 76. Second option applies to Model 94, T40S and T40L. Delete options for maximum door size not required.
 
9.
Maximum Door Size: 18 ft (5.5 m) wide by 16 ft (4.9 m) high. - 25 Ga product.
10.
Maximum Door Size: 20 ft (6.1 m) wide by 16 ft (4.9 m) high. - 24 Ga products
 
** NOTE TO SPECIFIER ** First option applies to Models 73 and 76. Second option applies to Model 94, T40S, T40L, T50S and T50L. Delete options for overall panel thickness not required.
 
11.
Overall Panel Thickness: 2.125 inches (54 mm).
12.
Overall Panel Thickness: 2 inches (51 mm).
 
** NOTE TO SPECIFIER ** First option applies to Models 73 and 76. Second option applies to Model 94, T40S and T40L. Delete options for steel skin thickness not required.
 
13.
Steel Skin Thickness: Minimum 25 gauge 0.019 inch (0.48 mm)
14.
Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm)
15.
End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.049 inch (1.25 mm) thick.
 
** NOTE TO SPECIFIER ** First option applies to Models 73, 76 and 94. Second option applies to Model T40S, T40L, T50S and T50L. Delete options for bottom sections not required.
 
16.
Bottom Panel Sections: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with bulb-shaped flexible PVC astragal.
17.
Bottom Sections: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with U-shaped flexible PVC astragal.
 
** NOTE TO SPECIFIER ** Delete options for windows not required.
 
18.
Windows: None, doors come standard with no windows.
 
** NOTE TO SPECIFIER ** The following applies to Model 73, 94, T40S and T50S. Delete if not required.
 
19.
Windows: Provide optional Decorative Insert Series Short Panel Windows; injection molded ASA plastic windows measuring 19-1/2 inches x 12 inches (495 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
a.
Glazing: 3/32 inches (2.5 mm) clear SSB glass.
b.
Glazing: 1/8 inches (3 mm) clear DSB glass.
c.
Glazing: 1/8 inches (3 mm) obscure DSB glass.
d.
Glazing: 1/8 inch (3 mm) Clear acrylic.
e.
Glazing: 1/8 inch (3 mm) Frosted glass.
f.
Glazing: 1/8 inch (3 mm) Rain glass.
g.
Glazing: 1/8 inch (3 mm) Seeded glass.
 
** NOTE TO SPECIFIER ** Delete decorative snap-in plastic inserts not required.
 
h.
Decorative Snap-in Plastic Inserts: Sunset 501.
i.
Decorative Snap-in Plastic Inserts: Sunset 502.
j.
Decorative Snap-in Plastic Inserts: Sunset 503.
k.
Decorative Snap-in Plastic Inserts: Sunset 504.
l.
Decorative Snap-in Plastic Inserts: Sunset 505.
m.
Decorative Snap-in Plastic Inserts: Sunset 506.
n.
Decorative Snap-in Plastic Inserts: Charleston 508.
o.
Decorative Snap-in Plastic Inserts: Colonial 509.
p.
Decorative Snap-in Plastic Inserts: Prairie 510.
 
** NOTE TO SPECIFIER ** The following applies to Model 73 and 94. Delete if not required.
 
20.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows; woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb. impact as per the Florida Building Code) measuring 19-1/2 inches x 12 inches (495 mm x 305 mm).
a.
Glazing: Clear Polycarbonate.
 
** NOTE TO SPECIFIER ** Delete decorative snap-in plastic inserts not required.
 
b.
Decorative Snap-in Plastic Inserts: Sunset 501.
c.
Decorative Snap-in Plastic Inserts: Sunset 502.
d.
Decorative Snap-in Plastic Inserts: Sunset 503.
e.
Decorative Snap-in Plastic Inserts: Sunset 504.
f.
Decorative Snap-in Plastic Inserts: Sunset 505.
g.
Decorative Snap-in Plastic Inserts: Sunset 506.
h.
Decorative Snap-in Plastic Inserts: Charleston 508.
i.
Decorative Snap-in Plastic Inserts: Colonial 509.
j.
Decorative Snap-in Plastic Inserts: Prairie 510.
 
** NOTE TO SPECIFIER ** The following applies to Model 73, 94, T40S and T50S. Delete if not required.
 
21.
Windows: Provide optional Decorative Short Panel Windows; injection molded ASA plastic windows measuring 19-1/2 inches x 12 inches (495 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) Carlisle Short, frosted DSB glass, leaded-look.
b.
Glazing: 1/8 inch (3 mm) Kristin Short, frosted DSB glass, leaded-look.
c.
Glazing: 1/8 inch (3 mm) Roselle Short, frosted DSB glass, leaded-look.
d.
Glazing: 1/8 inch (3 mm) Trenton Short, frosted DSB glass, leaded-look.
e.
Glazing: Tuscany Short wrought iron acrylic.
f.
Glazing: Orleans Short wrought iron acrylic.
 
** NOTE TO SPECIFIER ** The following applies to Model 73, 76, 94, T40S, T40L and T50S. Delete if not required.
 
22.
Windows: Provide optional Decorative Insert Series Long Panel Windows; injection molded ASA plastic windows measuring 40-1/2 inches x 12 inches (1029 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
a.
Glazing: 3/32 inch (2.5 mm) clear SSB glass.
b.
Glazing: 1/8 inch (3 mm) clear DSB glass.
c.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
d.
Glazing: 1/8 inch (3 mm) Clear acrylic.
e.
Glazing: 1/8 inch (3 mm) Frosted glass.
f.
Glazing: 1/8 inch (3 mm) Rain glass.
g.
Glazing: 1/8 inch (3 mm) Seeded glass.
 
** NOTE TO SPECIFIER ** Delete decorative snap-in plastic inserts not required.
 
h.
Decorative Snap-in Plastic Inserts: Sunset 601.
i.
Decorative Snap-in Plastic Inserts: Sunset 603.
j.
Decorative Snap-in Plastic Inserts: Sunset 605.
k.
Decorative Snap-in Plastic Inserts: Charleston 608.
l.
Decorative Snap-in Plastic Inserts: Prairie 610.
m.
Decorative Snap-in Plastic Inserts: Madison 611.
n.
Decorative Snap-in Plastic Inserts: Stockton 612.
o.
Decorative Snap-in Plastic Inserts: Madison Arch 613.
 
** NOTE TO SPECIFIER ** The following applies to Model 73, 76, 94, T40S, T40L, T50S and T50L. Delete if not required.
 
23.
Windows: Provide optional Decorative Long Panel Windows; injection molded ASA plastic windows measuring 40-1/2 inches x 12 inches (1029 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) Carlisle Long, frosted DSB glass, leaded-look.
b.
Glazing: 1/8 inch (3 mm) Kristin Long, frosted DSB glass, leaded-look.
c.
Glazing: 1/8 inch (3 mm) Roselle Long, frosted DSB glass, leaded-look.
d.
Glazing: 1/8 inch (3 mm) Trenton Long, frosted DSB glass, leaded-look.
e.
Glazing: Tuscany Long wrought iron acrylic.
f.
Glazing: Orleans Long wrought iron acrylic.
24.
Interior Finish: Woodgrain embossed texture with white interior color.
25.
Exterior Finish:
 
** NOTE TO SPECIFIER ** Applies to Model 73, 94, T40S and T50S. Delete if not required.
 
a.
Finish Type: Woodgrain embossed texture, Short Traditional Panel embossments.
 
** NOTE TO SPECIFIER ** Applies to Model 76, T40L and T50L. Delete exterior finish not required.
 
b.
Finish Type: Woodgrain embossed texture with Long Traditional Panel embossments.
 
** NOTE TO SPECIFIER ** Delete color not required.
 
c.
Color: White.
d.
Color: Almond.
e.
Color: Desert Tan.
f.
Color: Sandtone.
g.
Color: Chocolate.
 
** NOTE TO SPECIFIER ** Delete locking types not required.
 
26.
Locking: Standard, keyed spring-loaded lock bar.
27.
Locking: Provide optional keyed spring-loaded snap latches.
28.
Locking: Provide optional non-keyed interior slide bolt.
29.
Weatherstripping: Standard, Provide U-shaped bottom seal.
 
** NOTE TO SPECIFIER ** Perimeter seals are optional, choose from manufacturers standard options. Delete if not required.
 
30.
Perimeter Seals: _____.
31.
Tracks: Vertical tracks minimum 0.040 inch (1.02 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.051 inch (1.29 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required.
 
** NOTE TO SPECIFIER ** Delete track type not required.
 
a.
Track Type: Provide standard lift tracks.
b.
Track Type: Provide optional low headroom track.
c.
Track Type: Provide optional high lift track.
d.
Track Type: Provide optional follow-the-roof track.
e.
Track Width: 2 inches (50 mm).
 
** NOTE TO SPECIFIER ** 20 inch and 32 inch radius only available on doors up to 12 ft high. Delete track radius not required.
 
f.
Track Radius: 10 inch (254 mm).
g.
Track Radius: 12 inch (305 mm).
h.
Track Radius: 15 inch (381 mm).
i.
Track Radius: 20 inch (508 mm).
j.
Track Radius: 32 inch (813 mm).
2.7
RESIDENTIAL SECTIONAL DOORS - Coachman Collection
A.
Residential Sectional Doors: Coachman Collection Doors as manufactured by Clopay Building Products Company.
 
** NOTE TO SPECIFIER ** Delete models not required.
 
1.
Model: Clopay Model CD Series; Thermally-broken, 1-3/8" thick expanded polystyrene (EPS) insulated.
2.
Model: Clopay Model CG Series; Thermally-broken, 2 inches thick expanded polystyrene (EPS) insulated.
3.
Model: Clopay Model CGU Series; Intellicore 2 inches thick polyurethane insulated.
4.
Door Construction:
 
** NOTE TO SPECIFIER ** First option below applies to Models CD and CG. Second option applies to Model CGU. Delete models not required.
 
a.
Sections: Composite overlays adhered to base door constructed of pressure bonded expanded polystyrene (EPS) core construction between exterior and interior steel skins.
b.
Sections: Composite overlays adhered to base door constructed of foamed in place Intellicore core construction between exterior and interior steel skins.
c.
Exterior Steel Skins: Formed from flush commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
d.
Interior Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
e.
Section Joints: Sections formed to create tongue-in-groove meeting joint with thermal break.
f.
Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment.
g.
Connections: Stiles fastened to steel skins using Tog-L-Loc system.
h.
Handles: Black powder coated, hot-dipped galvanized step plate and lift handle (2 sets on doors over 10 ft wide) to comply with DASMA 116.
 
** NOTE TO SPECIFIER ** First option applies to Model CD. Second option applies to Model CG and CGU. Delete maximum door size not required.
 
5.
Maximum Door Size: 1-3/8 inch thick base door 18 ft (5.5 m) wide by 16 ft (4.9 m) high.
6.
Maximum Door Size: 2 inch thick base door 20 ft (6.1 m) wide by 16 ft (4.9 m) high.
 
** NOTE TO SPECIFIER ** First option applies to Models CD and CG. Second option applies to Model CGU. Delete maximum door size not required.
 
7.
Steel Skin Thickness: EPS Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior.
8.
Steel Skin Thickness: Intellicore Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 29 gauge 0.012 inch (0.30 mm) interior.
9.
End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 20 gauge, 0.034 inch (0.86 mm) thick.
10.
Bottom Section: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with U-shaped flexible PVC astragal.
11.
Thermal Resistance: Calculated in accordance with DASMA TDS-163.
 
** NOTE TO SPECIFIER ** First option applies to Model CD. Second option applies to Model CG. Third option applies to Model CGU. Delete options not required.
 
a.
R-Value: 6.5 deg F hr sq ft/Btu.
b.
R-Value: 9.0 deg F hr sq ft/Btu.
c.
R-Value: 18.4 deg F hr sq ft/Btu.
 
** NOTE TO SPECIFIER ** Delete options for windows not required.
 
12.
Windows: None, doors come standard with no windows.
13.
Windows: Provide optional REC11 Windows.
14.
Windows: Provide optional REC13 Windows.
15.
Windows: Provide optional REC14 Windows.
16.
Windows: Provide optional SQ23 Windows.
17.
Windows: Provide optional SQ24 Windows.
18.
Windows: Provide optional ARCH1 Windows.
19.
Windows: Provide optional ARCH3 Windows.
20.
Windows: Provide optional ARCH4 Windows.
21.
Windows: Provide optional ARC1A Windows.
22.
Windows: Provide optional ARC3A Windows.
23.
Windows: Provide optional ARC4A Windows.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
24.
Glazing: 1/8 inch (3 mm) clear DSB glass.
25.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
26.
Glazing: 1/8 inch (3 mm) seeded DSB glass.
27.
Glazing: 1/2 inch (12 mm) insulated clear DSB glass.
28.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
29.
Glazing: 1/2 inch (12 mm) insulated seeded DSB glass.
30.
Glazing: 1/8 inch (3 mm) Frosted glass.
31.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
32.
Glazing: 1/8 inch (3 mm) Rain glass.
33.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
34.
Window Height: As scheduled and indicated on Drawings in accordance with manufacturer's guidelines.
35.
Window Width: As scheduled and indicated on Drawings in accordance with manufacturer's guidelines.
 
** NOTE TO SPECIFIER ** First option applies to Model CD and CG, Second option applies to Model CGU. Delete finish not required.
 
36.
Interior Finish: Stucco embossed texture with flush design, white interior color.
37.
Interior Finish: Stucco embossed texture with shallow U ribbed pattern, white interior color.
38.
Steel Base Door Exterior Finish: Woodgrain embossed texture with flush design.
 
** NOTE TO SPECIFIER ** Delete colors not required.
 
a.
Color: White.
b.
Color: Almond.
c.
Color: Desert Tan.
d.
Color: Sandtone.
39.
Composite Overlays Exterior Finish: Woodgrain embossed texture with beveled coped edges.
 
** NOTE TO SPECIFIER ** Delete colors not required.
 
a.
Color: White.
b.
Color: Almond.
c.
Color: Desert Tan.
d.
Color: Sandtone.
 
** NOTE TO SPECIFIER ** Delete locking type not required.
 
40.
Locking: Standard, non-keyed interior slide bolt.
41.
Locking: Provide optional decorative keyed snap latch lock.
42.
Weatherstripping: Standard, Provide U-shaped bottom seal.
 
** NOTE TO SPECIFIER ** Perimeter seals are optional, choose from manufacturers standard options. Delete if not required.
 
43.
Perimeter Seals: _____.
44.
Tracks: Vertical tracks minimum 0.060 inch (1.524 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.075 inch (1.905 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required.
 
** NOTE TO SPECIFIER ** Delete track type not required.
 
a.
Track Type: Provide standard lift tracks.
b.
Track Type: Provide optional low headroom track.
c.
Track Type: Provide optional high lift track.
d.
Track Type: Provide optional follow-the-roof track.
e.
Track Width: 2 inches (50 mm).
 
** NOTE TO SPECIFIER ** 20 inch and 32 inch radius only available on doors up to 12 ft high. Delete track radius not required.
 
f.
Track Radius: 10 inch (254 mm).
g.
Track Radius: 12 inch (305 mm).
h.
Track Radius: 15 inch (381 mm).
i.
Track Radius: 20 inch (508 mm).
j.
Track Radius: 32 inch (813 mm).
2.8
RESIDENTIAL STEEL SECTIONAL DOORS - Gallery Collection
A.
Residential Steel Sectional Doors: Gallery Collection Doors as manufactured by Clopay Building Products Company.
 
** NOTE TO SPECIFIER ** Delete models not required.
 
1.
Model: GD4S, Non-insulated.
2.
Model: GD4L, Non-insulated.
3.
Model: GD4SV, polystyrene insulated.
4.
Model: GD4LV, polystyrene insulated.
5.
Model: GD5S, Non-insulated
6.
Model: GD5SV, polystyrene insulated.
 
** NOTE TO SPECIFIER ** The following applies to Models GD4SV, GD4LV and GD5SV. Delete if not required.
 
7.
Thermal Resistance (R-value): 6.3 deg F hr sq ft/Btu; calculated in accordance with DASMA TDS-163.
8.
Door Construction:
 
** NOTE TO SPECIFIER ** First option below applies to Models GD4S, GD4L and GD5S. Second option applies to Models GD4SV, GD4LV and GD5SV. Delete options for sections not required.
 
a.
Sections: Steel frame and skin construction.
b.
Sections: Steel frame and skin construction with 1-5/16 inch thick polystyrene insulation with vinyl backer.
 
** NOTE TO SPECIFIER ** First option below applies to Models GD4S, GD4SV, GD5S and GD5SV. Second option applies to Models GD4L and GD4LV. Delete steel skins not required.
 
c.
Steel Skins: Formed from Short Grooved Panel embossed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
d.
Steel Skins: Formed from Long Grooved Panel embossed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
e.
Section Joints: Sections formed to create shiplap meeting joint.
f.
Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment.
g.
Door Stiles: Galvanized steel end stiles and center stiles, pre-punched for easy hinge attachment.
h.
Connections: Stiles fastened to steel skins using Tog-L-Loc system.
i.
Handles: Black powder coated, hot-dipped galvanized step plate and lift handle (2 sets on doors over 10 ft wide) to comply with DASMA 116.
9.
Maximum Door Size: 18 feet (5.5 m) wide by 16 feet (4.9 m) high for GD5S & GD5SV. UP to 20 feet ft (5.5 m) wide by 16 feet (4.9 m) for GD4S, GD4L, GD4SV, GD4LV.
10.
Overall Panel Thickness: 2.125 inches (54 mm).
 
** NOTE TO SPECIFIER ** First option below applies to Models GD4S, GD4L, GD4SV, GD4LV. Second option applies to Models GD5S and GD5SV. Delete steel skins not required.
 
11.
Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm).
12.
Steel Skin Thickness: Minimum 25 gauge 0.019 inch (0.48 mm).
13.
End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.049 inch (1.25 mm) thick.
14.
Bottom Section: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with bulb-shaped flexible PVC astragal.
 
** NOTE TO SPECIFIER ** Delete options for windows not required.
 
15.
Windows: None, doors come standard with no windows.
16.
Windows: Provide optional Architectural Series Short Windows; extruded cellular PVC windows measuring 19 -1/2 inches x 16 inches.
 
** NOTE TO SPECIFIER ** Grilles only available with first two glazing options. Delete grilles not required.
 
a.
Grilles: Short with square grilles, SQ22.
b.
Grilles: Short with rectangular grilles, REC11.
c.
Grilles: Plain Short, no grilles.
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/8 inch (3 mm) Frosted glass.
g.
Glazing: 1/8 inch (3 mm) Rain glass.
h.
Glazing: 1/8 inch (3 mm) Seeded glass.
i.
Glazing: 1/8 inch (3 mm) Kristin Short, frosted DSB glass, leaded-look.
j.
Glazing: 1/8 inch (3 mm) Trenton Short, frosted DSB glass, leaded-look.
k.
Glazing: 1/8 inch (3 mm) Clayton Short, frosted DSB glass, leaded-look.
l.
Glazing: Wrought Iron Short, acrylic.
17.
Windows: Provide optional Architectural Series Long Windows; extruded cellular PVC windows measuring 42 inches x 16 inches.
 
** NOTE TO SPECIFIER ** Grilles available only with first two glazing options. Delete if not required.
 
a.
Grilles: Long with square grilles, SQ24.
b.
Grilles: Long with rectangular grilles, REC14.
c.
Grilles: Plain Long, no grilles.
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/8 inch (3 mm) Frosted glass.
g.
Glazing: 1/8 inch (3 mm) Rain glass.
h.
Glazing: 1/8 inch (3 mm) Seeded glass.
i.
Glazing: 1/8 inch (3 mm) Kristin Long frosted DSB glass, leaded-look.
j.
Glazing: 1/8 inch (3 mm) Trenton Long, frosted DSB glass, leaded-look.
k.
Glazing: 1/8 inch (3 mm) Clayton Long, frosted DSB glass, leaded-look.
l.
Glazing: Wrought Iron Long, acrylic.
18.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows, woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb impact as per the Florida Building Code) measuring 19-1/2 inches x 16 inches (495 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: Clear polycarbonate.
b.
Glazing: Matte polycarbonate.
c.
Glazing: Bronze polycarbonate.
d.
Glazing: Pebbled polycarbonate.
e.
Grilles: Short with square grilles, SQ22.
f.
Grilles: Plain Short, no grilles.
19.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows, woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb impact as per the Florida Building Code) measuring 42 inches x 16 inches (1067 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: Clear polycarbonate.
b.
Glazing: Matte polycarbonate.
c.
Glazing: Bronze polycarbonate.
d.
Glazing: Pebbled polycarbonate
e.
Grilles: Long with square grilles, SQ24.
f.
Grilles: Plain Long, no grilles.
20.
Windows: Provide optional Architectural Series ARCH1 Windows; extruded cellular PVC windows measuring 42 inches x 16 inches with a 159 -1/2 inch radius top.
 
** NOTE TO SPECIFIER ** Delete grilles not required.
 
a.
Grilles: Snap-in plastic square grilles.
b.
Grilles: Vertical grilles.
c.
Grilles: Plain, no grilles.
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/8 inch (3 mm) Frosted glass.
g.
Glazing: 1/8 inch (3 mm) Rain glass.
h.
Glazing: 1/8 inch (3 mm) Seeded glass.
21.
Windows: Provide optional Architectural Series ARCH2 Windows; extruded cellular PVC windows measuring 42 inches x 16 inches with a 39-3/4 inch radius top.
 
** NOTE TO SPECIFIER ** Grilles available only with first two glazing options. Delete if not required.
 
a.
Grilles: Snap-in plastic square grilles.
b.
Grilles: Vertical grilles.
c.
Grilles: Plain, no grilles.
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/8 inch (3 mm) Frosted glass.
g.
Glazing: 1/8 inch (3 mm) Rain glass.
h.
Glazing: 1/8 inch (3 mm) Seeded glass.
i.
Glazing: Wrought Iron ARCH, acrylic.
22.
Windows: Provide optional Architectural Series ARCH3 Window Design; created by mixing Architectural Series Long windows measuring 42 inches x 16 inches with ARCH1 windows measuring 42 inches x 16 inches with a 159 -1/2 inch radius top.
 
** NOTE TO SPECIFIER ** Delete grilles not required.
 
a.
Grilles: Snap-in plastic square grilles.
b.
Grilles: Vertical grilles.
c.
Grilles: Plain, no grilles.
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/8 inch (3 mm) Frosted glass.
g.
Glazing: 1/8 inch (3 mm) Rain glass.
h.
Glazing: 1/8 inch (3 mm) Seeded glass.
 
** NOTE TO SPECIFIER ** First option below applies to Models GD4S, GD4L and GD5S. Second option applies to Models GD4SV, GD4LV and GD5SV. Delete options for interior finish not required.
 
23.
Interior Finish: Woodgrain embossed texture with white interior color.
24.
Interior Finish: Vinyl backer over polystyrene insulation.
25.
Exterior Finish:
 
** NOTE TO SPECIFIER ** First option below applies to Models GD4S, GD4SV, GD5S and GD5SV. Second option applies to Models GD4L and GD4LV. Delete steel skins not required.
 
a.
Finish Type: Woodgrain embossed texture with Short Grooved Panel embossments.
b.
Finish Type: Woodgrain embossed texture with Long Grooved Panel embossments:
 
** NOTE TO SPECIFIER ** Delete colors not required.
 
c.
Color: White.
d.
Color: Almond.
e.
Color: Desert Tan.
f.
Color: Sandtone.
g.
Color: Chocolate.
h.
Color: Clopay Color Blast ____.
 
** NOTE TO SPECIFIER ** Delete locking types not required.
 
26.
Locking: Standard, keyed spring-loaded lock bar.
27.
Locking: Provide optional keyed spring-loaded snap latches.
28.
Locking: Provide optional non-keyed interior slide bolt.
29.
Weatherstripping: Standard, Provide bulb-shaped bottom seal.
 
** NOTE TO SPECIFIER ** Perimeter seals are optional, choose from manufacturers standard options. Delete if not required.
 
30.
Perimeter Seals: _____.
31.
Tracks: Vertical tracks minimum 0.040 inch (1.02 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.051 inch (1.29 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required.
 
** NOTE TO SPECIFIER ** Delete track type not required.
 
a.
Track Type: Provide standard lift tracks.
b.
Track Type: Provide optional low headroom track.
c.
Track Type: Provide optional high lift track.
d.
Track Type: Provide optional follow-the-roof track.
e.
Track Width: 2 inches (50 mm).
 
** NOTE TO SPECIFIER ** 20 inch and 32 inch radius only available on doors up to 12 ft high. Delete track radius not required.
 
f.
Track Radius: 10 inch (254 mm).
g.
Track Radius: 12 inch (305 mm).
h.
Track Radius: 15 inch (381 mm).
i.
Track Radius: 20 inch (508 mm).
j.
Track Radius: 32 inch (813 mm).
2.9
RESIDENTIAL STEEL SECTIONAL DOORS - Gallery Collection
A.
Residential Steel Sectional Doors: Gallery Collection Doors as manufactured by Clopay Building Products Company.
 
** NOTE TO SPECIFIER ** Delete models not required.
 
1.
Model: GD1SP, Thermally-Broken, Expanded Polystyrene (EPS) Insulated.
2.
Model: GD1LP, Thermally-Broken, Expanded Polystyrene (EPS) Insulated.
3.
Model: GD1SU, Thermally-Broken, Intellicore Polyurethane Insulated.
4.
Model: GD1LU, Thermally-Broken, Intellicore Polyurethane Insulated.
5.
Model: GD2SP, Thermally-Broken, Expanded Polystyrene (EPS) Insulated.
6.
Model: GD2LP, Thermally-Broken, Expanded Polystyrene (EPS) Insulated.
7.
Model: GD2SU, Thermally-Broken, Intellicore Polyurethane Insulated.
8.
Model: GD2LU, Thermally-Broken, Intellicore Polyurethane Insulated.
9.
Door Construction:
 
** NOTE TO SPECIFIER ** First option applies to Models GD1SP, GD1LP, GD2SP, GD2LP. Second option applies to Model GD1SU, GD1LU, GD2SU and GD2LU. Delete if not required.
 
a.
Sections: Pressure bonded expanded polystyrene (EPS) core construction between exterior and interior steel skins.
b.
Sections: Foamed in place Intellicore Polyurethane core construction between exterior and interior steel skins.
 
** NOTE TO SPECIFIER ** First option applies to Model GD1SP, GD1SU,GD2SP and GD2SU. Second option applies to Model GD1LP, GD1LU,GD2LP and GD2LU. Delete if not required.
 
c.
Exterior Steel Skins: Formed from Short Grooved Panel embossed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
d.
Exterior Steel Skins: Formed from Long Grooved Panel embossed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
e.
Interior Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
f.
Section Joints: Sections formed to create tongue-in-groove meeting joint with thermal break.
g.
Door Stiles: Galvanized steel end stiles and center stiles, pre-punched for easy hinge attachment.
h.
Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment.
i.
Handles: Black powder coated, hot-dipped galvanized step plate and lift handle (2 sets on doors over 10 ft wide) to comply with DASMA 116.
 
** NOTE TO SPECIFIER ** First option applies to Models GD1SP, GD1LP, GD1SU and GD1LU. Second option applies to Model GD2SP, GD2LP, GD2SU, and GD2LU. Delete if not required.
 
10.
Maximum Door Size: 18 ft (5.5 m) wide by 16 ft (4.9 m) high.
11.
Maximum Door Size: 20 ft (6.1 m) wide by 16 ft (4.9 m) high.
 
** NOTE TO SPECIFIER ** First option applies to Models GD1SP, GD1LP, GD1SU and GD1LU. Second option applies to Model GD2SP, GD2LP, GD2SU, and GD2LU. Delete if not required.
 
12.
Overall Panel Thickness: 1.375 inches (35 mm).
13.
Overall Panel Thickness: 2 inches (35 mm).
 
** NOTE TO SPECIFIER ** First option applies to Models GD1SP, GD1LP, GD2SP and GD2LP. Second option applies to Model GD2SP, GD2LP, GD2SU, and GD2LU. Delete if not required. Third option applies to Models GD1SP, GD1LP, GD2SP and GD2LP in Black and all Ultra-Grain Finishes. Fourth option applies to Model GD2SP, GD2LP, GD2SU, and GD2LU. Delete if not required in Black and all Ultra-Grain Finishes.
 
14.
Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior.
15.
Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 29 gauge 0.012 inch (0.30 mm) interior.
16.
Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.55 mm) exterior; minimum 28 gauge 0.015 inch (0.38 mm) interior.
17.
Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.55 mm) exterior; minimum 29 gauge 0.012 inch (0.30 mm) interior.
18.
End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 20 gauge, 0.034 inch (0.86 mm) thick.
19.
Bottom Section: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with U-shaped flexible PVC astragal.
20.
Thermal Resistance: Calculated in accordance with DASMA TDS-163
 
** NOTE TO SPECIFIER ** First option applies to Models GD1SP, GD1LP. Second option applies to models GD2SP and GD2LP. Third option applies to Model GD1SU and GD1LU. Fourth option applies to Models GD2SU and GD2LU. Delete options not required.
 
a.
R-Value: 6.5 deg F hr sq ft/Btu.
b.
R-Value: 9.0 deg F hr sq ft/Btu.
c.
R-Value: 12.9 deg F hr sq ft/Btu.
d.
R-Value: 18.4 deg F hr sq ft/Btu.
 
** NOTE TO SPECIFIER ** Delete options for windows not required.
 
21.
Windows: None, doors come standard with no windows.
22.
Windows: Provide optional Architectural Series Short Windows; extruded cellular PVC windows measuring 19-1/2 inches x 16 inches.
 
** NOTE TO SPECIFIER ** Grilles available only with first four glazing options. Delete if not required.
 
a.
Grilles: Short with square grilles, SQ22.
b.
Grilles: Short with rectangular grilles, REC11.
c.
Grilles: Plain Short, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Rain glass.
k.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
l.
Glazing: 1/8 inch (3 mm) Seeded glass.
m.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
n.
Glazing: 1/8 inch (3 mm) Kristin Short, frosted DSB glass, leaded-look.
o.
Glazing: 1/8 inch (3 mm) Trenton Short, frosted DSB glass, leaded-look.
p.
Glazing: 1/8 inch (3 mm) Clayton Short, frosted DSB glass, leaded-look.
q.
Glazing: 1/2 inch (12 mm) Kristin Short, frosted insulated DSB glass, leaded-look.
r.
Glazing: 1/2 inch (12 mm) Trenton Short, frosted insulated DSB glass, leaded-look.
s.
Glazing: 1/2 inch (12 mm) Clayton Short, frosted insulated DSB glass, leaded-look.
t.
Glazing: Wrought Iron Short, acrylic.
23.
Windows: Provide optional Architectural Series Long Windows, extruded cellular PVC windows measuring 42 inches x 16 inches.
 
** NOTE TO SPECIFIER ** Grilles available only with first four glazing options. Delete if not required.
 
a.
Grilles: Long with square grilles, SQ24.
b.
Grilles: Long with rectangular grilles, REC14.
c.
Grilles: Plain Long, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Rain glass.
k.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
l.
Glazing: 1/8 inch (3 mm) Seeded glass.
m.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
n.
Glazing: 1/8 inch (3 mm) Kristin Long, frosted DSB glass, leaded-look.
o.
Glazing: 1/8 inch (3 mm) Trenton Long frosted DSB glass, leaded-look.
p.
Glazing: 1/8 inch (3 mm) Clayton Long, frosted DSB glass, leaded-look.
q.
Glazing: 1/2 inch (12 mm) Kristin Long, frosted insulated DSB glass, leaded-look.
r.
Glazing: 1/2 inch (12 mm) Trenton Long, frosted insulated DSB glass, leaded-look.
s.
Glazing: 1/2 inch (12 mm) Clayton Long, frosted insulated DSB glass, leaded-look.
t.
Glazing: Wrought Iron Long, acrylic.
24.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows, woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb impact as per the Florida Building Code) measuring 19-12 inches x 16 inches (495 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing and grilles not required.
 
a.
Glazing: Clear polycarbonate.
b.
Glazing: Matte polycarbonate.
c.
Glazing: Bronze polycarbonate.
d.
Glazing: Pebbled polycarbonate.
e.
Grilles: Short with square grilles, SQ22.
f.
Grilles: Plain Short, no grilles.
25.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows, woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb impact as per the Florida Building Code) measuring 42 inches x 16 inches (1067 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing and grilles not required.
 
a.
Glazing: Clear polycarbonate.
b.
Glazing: Matte polycarbonate.
c.
Glazing: Bronze polycarbonate.
d.
Glazing: Pebbled polycarbonate.
e.
Grilles: Long with square grilles, SQ24.
f.
Grilles: Plain Long, no grilles.
26.
Windows: Provide optional Architectural Series ARCH1 Windows; extruded cellular PVC windows measuring 42 inches x 16 inches with a 159-1/2 inch radius top.
 
** NOTE TO SPECIFIER ** Delete grilles not required.
 
a.
Grilles: Snap-in plastic square grilles.
b.
Grilles: Vertical grilles.
c.
Grilles: Plain, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Rain glass.
k.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
l.
Glazing: 1/8 inch (3 mm) Seeded glass.
m.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
27.
Windows: Provide optional Architectural Series ARCH2 Windows; extruded cellular PVC windows measuring 42 inches x 16 inches with a 39-3/4 inches radius top.
 
** NOTE TO SPECIFIER ** Delete grilles not required.
 
a.
Grilles: Snap-in plastic square grilles.
b.
Grilles: Vertical grilles.
c.
Grilles: Plain, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Rain glass.
k.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
l.
Glazing: 1/8 inch (3 mm) Seeded glass.
m.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
n.
Glazing: Wrought Iron ARCH, Acrylic.
28.
Windows: Provide optional Architectural Series ARCH3 Window Design; created by mixing Architectural Series Long windows measuring 42 inches x 16 inches with ARCH1 windows measuring 42 inches x 16 inches with a 159-1/2 inch radius top.
 
** NOTE TO SPECIFIER ** Delete grilles not required.
 
a.
Grilles: Snap-in plastic square grilles.
b.
Grilles: Vertical grilles.
c.
Grilles: Plain, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Rain glass.
k.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
l.
Glazing: 1/8 inch (3 mm) Seeded glass.
m.
Glazing: 1/2 inch (12 mm) insulated Seeded glass.
 
** NOTE TO SPECIFIER ** First option applies to Models GD1SP, GD1LP, GD2SP and GD2LP. Second option applies to Model GD1SU, GD1LU, GD2SU and GD2LU. Delete if not required.
 
29.
Interior Finish: Stucco embossed texture with flush design, white interior color.
30.
Interior Finish: Stucco embossed texture with shallow U-ribbed pattern, white interior color.
31.
Exterior Finish:
 
** NOTE TO SPECIFIER ** First option applies to Model GD1SP, GD2SP, GD1SU and GD2SU. Second option applies to Model GD1LP, GD2LP, GD1LU and GD2LU. Delete if not required.
 
a.
Finish Type: Woodgrain embossed texture with Short Grooved Panel embossments.
b.
Finish Type: Woodgrain embossed texture with Long Grooved Panel embossments.
 
** NOTE TO SPECIFIER ** Delete colors not required.
 
c.
Color: Standard White.
d.
Color: Glacier White.
e.
Color: Almond.
f.
Color: Desert Tan.
g.
Color: Sandtone.
h.
Color: Bronze.
i.
Color: Chocolate.
j.
Color: Mocha Brown.
k.
Color: Black
l.
Color: Clopay Color Blast _____.
32.
Exterior Finish:
 
** NOTE TO SPECIFIER ** First option applies to Model GD1SP, GD2SP, and GD2SU. Second option applies to Model GD1LP, GD2LP, and GD2LU. Options are not available for Models GD1SU and GD1LU. Delete if not required.
 
a.
Finish Type: Ultra-Grain Exterior Finish; stucco embossed texture with Short Grooved Panel embossments
b.
Finish Type: Ultra-Grain Exterior Finish; stucco embossed texture with Long Grooved Panel embossments.
 
** NOTE TO SPECIFIER ** Options are not available for Models GD1SU and GD1LU. Delete color not required.
 
c.
Color: Ultra-Grain Oak Medium Finish.
d.
Color: Ultra-Grain Oak Dark Finish.
e.
Color: Ultra-Grain Oak Walnut Finish.
 
** NOTE TO SPECIFIER ** Delete locking types not required.
 
33.
Locking: Standard, keyed spring-loaded lock bar.
34.
Locking: Provide optional keyed spring-loaded snap latches.
35.
Locking: Provide optional non-keyed interior slide bolt.
36.
Weatherstripping: Standard, Provide U-shaped bottom seal.
 
** NOTE TO SPECIFIER ** Perimeter seals are optional, choose from manufacturers standard options. Delete if not required.
 
37.
Perimeter Seals: _____.
38.
Tracks: Vertical tracks minimum 0.040 inch (1.016 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.060 inch (1.524 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required.
 
** NOTE TO SPECIFIER ** Delete track type not required.
 
a.
Track Type: Provide standard lift tracks.
b.
Track Type: Provide optional low headroom track.
c.
Track Type: Provide optional high lift track.
d.
Track Type: Provide optional follow-the-roof track.
e.
Track Width: 2 inches (50 mm).
 
** NOTE TO SPECIFIER ** 20 inch and 32 inch radius only available on doors up to 12 ft high. Delete track radius not required.
 
f.
Track Radius: 10 inch (254 mm).
g.
Track Radius: 12 inch (305 mm).
h.
Track Radius: 15 inch (381 mm).
i.
Track Radius: 20 inch (508 mm).
j.
Track Radius: 32 inch (813 mm).
2.10
RESIDENTIAL SECTIONAL DOORS - Grand Harbor Collection
A.
Residential Sectional Doors: Grand Harbor Collection as manufactured by Clopay Building Products Company.
1.
Model: GH11 24-ga, Wood-grain Embossed Flush Steel Pan Doors w/Decorative Composite Overlays.
2.
Model: GH12 24-ga, Wood-grain Embossed Flush Steel Pan Doors w/Decorative Composite Overlays.
3.
Model: GH13 24-ga, Wood-grain Embossed Flush Steel Pan Doors w/Decorative Composite Overlays.
4.
Model: GH21 24-ga, Wood-grain Embossed Flush Steel Pan Doors w/Decorative Composite Overlays.
5.
Model: GH22 24-ga, Wood-grain Embossed Flush Steel Pan Doors w/Decorative Composite Overlays.
6.
Model: GH31 24-ga, Wood-grain Embossed Flush Steel Pan Doors w/Decorative Composite Overlays.
7.
Model: GH36 24-ga, Wood-grain Embossed Flush Steel Pan Doors w/Decorative Composite Overlays.
8.
Model: GH41 24-ga, Wood-grain Embossed Flush Steel Pan Doors w/Decorative Composite Overlays.
9.
Model: GH00: 24-ga, Wood-grain Embossed Flush Steel Pan Replacement Sections w/ no Overlays.
10.
Door Construction:
 
** NOTE TO SPECIFIER ** Thermal resistance subparagraph does not apply to first option. Delete option for section not required.
 
a.
Sections: Composite overlays adhered to base door constructed of steel frame and skin construction.
b.
Sections: Composite overlays adhered to base door constructed of steel frame and skin construction with 1-5/8 inch thick expanded polystyrene (EPS) insulation with vinyl backer.
c.
Steel Skins: Formed from flush commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
d.
Section Joints: Sections formed to create shiplap meeting joint.
e.
Door Stiles: Galvanized steel end stiles and center stiles, pre-punched for easy hinge attachment.
f.
Connections: Stiles fastened to steel skins using Tog-L-Loc system.
g.
Handles: Black powder coated, hot-dipped galvanized step plate and lift handle (2 sets on doors over 10 ft wide) to comply with DASMA 116.
11.
Maximum Door Size: 18 ft (5.5 m) wide by 12 ft (3.66 m) high.
12.
Base Door Thickness: 2.125 inches (54 mm).
13.
Overall Panel Thickness: 2.625 inches (67 mm).
14.
Steel Skin Thickness: Minimum 24 gauge 0.022 inch (0.56 mm).
15.
End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 18 gauge, 0.049 inch (1.25 mm) thick.
16.
Bottom Section: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with U-shaped flexible PVC astragal.
 
** NOTE TO SPECIFIER ** Delete thermal resistance paragraph below if insulation is not required.
 
17.
Thermal Resistance (R-value): 6.3 deg F hr sq ft/Btu ; calculated in accordance with DASMA TDS-163.
 
** NOTE TO SPECIFIER ** Delete options for windows not required.
 
18.
Windows: None, doors come standard with no windows.
19.
Windows: Provide optional Short Windows; extruded cellular PVC windows measuring 19-1/2 inches x 16 inches.
 
** NOTE TO SPECIFIER ** Grilles only available with first two glazing options. Delete grilles not required.
 
a.
Grilles: Snap-in plastic square grilles, SQ22.
b.
Grilles: Rectangular grilles, REC12.
c.
Grilles: Plain Short, no grilles.
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: Wrought Iron Short, acrylic.
20.
Windows: Provide optional Long Windows: Extruded cellular PVC windows measuring 42 inches x 16 inches.
 
** NOTE TO SPECIFIER ** Grilles only available with first two glazing options. Delete grilles not required.
 
a.
Grilles: Snap-in plastic square grilles, SQ24.
b.
Grilles: Rectangular grilles, REC14.
c.
Grilles: Plain Long, no grilles.
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: Wrought Iron Long, acrylic.
21.
Windows: Provide optional ARCH1 Windows; extruded cellular PVC windows measuring 42 inches x 16 inches with a 159-1/2 inch radius top.
 
** NOTE TO SPECIFIER ** Delete glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) clear DSB glass.
b.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
 
** NOTE TO SPECIFIER ** Delete grilles not required.
 
c.
Grilles: Snap-in plastic square grilles, GRLA1.
d.
Grilles: Vertical grilles, GRVA1.
e.
Grilles: Plain, no grilles.
22.
Windows: Provide optional XG24 "Faux Window" Design, measuring 42 inches x 16 inches, created using a solid dark gray steel background with decorative snap-in plastic Grilles.
a.
Glazing: None.
23.
Windows: Provide optional XG14 "Faux Window" Design, measuring 42 inches x 16 inches, created using a solid dark gray steel background with decorative snap-in plastic Grilles.
a.
Glazing: None.
24.
Windows: Provide optional XA24 "Faux Window" Design, measuring 42 inches x 16 inches with a 159-1/2 inch radius top, created using a solid dark gray steel background with decorative snap-in plastic Grilles.
a.
Glazing: None.
25.
Interior Finish: Vinyl backer over expanded polystyrene (EPS) insulation.
26.
Exterior Finish: Base Door Woodgrain embossed texture with flush design.
 
** NOTE TO SPECIFIER ** Delete colors not required.
 
a.
Color: White.
b.
Color: Almond.
c.
Color: Desert Tan.
d.
Color: Sandtone.
 
** NOTE TO SPECIFIER ** Delete locking type not required.
 
27.
Locking: Standard, non-keyed interior slide bolt.
28.
Locking: Provide optional decorative keyed snap latch lock.
29.
Weatherstripping: Standard, Provide bulb shaped bottom seal.
 
** NOTE TO SPECIFIER ** Perimeter seals are optional, choose from manufacturers standard options. Delete if not required.
 
30.
Perimeter Seals: _____.
31.
Tracks: Vertical tracks minimum 0.040 inch (1.016 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.060 inch (1.524 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required.
 
** NOTE TO SPECIFIER ** Delete track type not required.
 
a.
Track Type: Provide standard lift tracks.
b.
Track Type: Provide optional low headroom track.
c.
Track Type: Provide optional high lift track.
d.
Track Type: Provide optional follow-the-roof track.
e.
Track Width: 2 inches (50 mm).
 
** NOTE TO SPECIFIER ** 20 inch and 32 inch radius only available on doors up to 12 ft high. Delete track radius not required.
 
f.
Track Radius: 10 inch (254 mm).
g.
Track Radius: 12 inch (305 mm).
h.
Track Radius: 15 inch (381 mm).
i.
Track Radius: 20 inch (508 mm).
j.
Track Radius: 32 inch (813 mm).
2.11
RESIDENTIAL SECTIONAL DOORS - Canyon Ridge Collection
A.
Residential Sectional Doors: Canyon Ridge Collection as manufactured by Clopay Building Products Company.
 
** NOTE TO SPECIFIER ** Delete models not required.
 
1.
Model: Clopay Model CAN2 Limited Edition Series Doors.
2.
Model: Clopay Model CAN2 Ultra-Grain Series Doors.
3.
Door Construction:
a.
Sections: Composite cladding and overlays adhered to base door constructed of foamed in place Intellicore polyurethane core construction between exterior and interior steel skins.
b.
Exterior Steel Skins: Formed from flush commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
c.
Interior Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
d.
Section Joints: Sections formed to create weather tight tongue-in-groove meeting joint with thermal break.
e.
Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment.
f.
Door Stiles: Galvanized steel end stiles and center stiles, pre-punched for easy hinge attachment.
g.
Handles: Black powder coated, hot-dipped galvanized step plate and lift handle (2 sets on doors over 10 ft wide) to comply with DASMA 116.
4.
Maximum Door Size: 20 ft (6.1 m) wide by 10 ft (3.05 m) high.
5.
Base Door Thickness: 2 inches (51 mm).
 
** NOTE TO SPECIFIER ** First option applies to Limited Edition. Second option applies to Ultra-Grain. Delete overall panel thickness not required.
 
6.
Overall Panel Thickness: 3 inches (76.2 mm).
7.
Overall Panel Thickness: 2.5 inches (63.5 mm).
8.
Steel Skin Thickness: Minimum 27 gauge 0.016 inch (0.40 mm) exterior; minimum 29 gauge 0.012 inch (0.30 mm) interior.
9.
End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 20 gauge, 0.034 inch (0.86 mm) thick.
10.
Bottom Section: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with U-shaped flexible PVC astragal.
11.
Thermal Resistance: Calculated in accordance with DASMA TDS-16.
 
** NOTE TO SPECIFIER ** First option applies to Limited Edition. Second option applies to Ultra-Grain. Delete option not required.
 
a.
R-Value: 20.4 deg F hr sq ft/Btu.
b.
R-Value: 18.4 deg F hr sq ft/Btu.
 
** NOTE TO SPECIFIER ** Delete options for windows not required.
 
12.
Windows: None, doors come standard with no windows.
13.
Windows: Provide optional REC11 Windows.
14.
Windows: Provide optional REC13 Windows.
15.
Windows: Provide optional REC14 Windows.
16.
Windows: Provide optional SQ23 Windows.
17.
Windows: Provide optional SQ24 Windows.
18.
Windows: Provide optional ARCH1 Windows.
19.
Windows: Provide optional ARCH3 Windows.
20.
Windows: Provide optional ARCH4 Windows.
21.
Windows: Provide optional ARC1A Windows.
22.
Windows: Provide optional ARC3A Windows.
23.
Windows: Provide optional ARC4A Windows.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
24.
Glazing: 1/8 inch (3 mm) clear DSB glass.
25.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
26.
Glazing: 1/8 inch (3 mm) seeded DSB glass.
27.
Glazing: 1/2 inch (12 mm) insulated clear DSB glass.
28.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
29.
Glazing: 1/2 inch (12 mm) insulated seeded DSB glass.
30.
Glazing: 1/8 inch (3 mm) Frosted glass.
31.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
32.
Glazing: 1/8 inch (3 mm) Rain glass.
33.
Glazing: 1/2 inch (12 mm) insulated Rain glass.
 
** NOTE TO SPECIFIER ** Delete options for window height not required.
 
34.
Window Height: 11 inches (279.4 mm) on 21 inches (533.4 mm) high sections.
35.
Window Height: 14 inches (355.6 mm) on 24 inches (609.6 mm) high sections.
36.
Window Width: As scheduled and indicated on Drawings in accordance with manufacturer's guidelines.
37.
Interior Finish: Stucco embossed texture with shallow U ribbed pattern, white interior color.
 
** NOTE TO SPECIFIER ** The following option applies only to Limited Edition. Delete if not required.
 
38.
Exterior Finish: Composite cladding.
 
** NOTE TO SPECIFIER ** Whitewash finish available only on Mahogany cladding. Factory primed finish must be painted or stained in field. Delete option for color not required.
 
a.
Color: Medium Finish.
b.
Color: Dark Finish.
c.
Color: Walnut Finish.
d.
Color: Whitewash Finish.
e.
Color: Primed.
 
** NOTE TO SPECIFIER ** Delete option for texture not required.
 
f.
Texture: Clear Cypress woodgrain.
g.
Texture: Pecky Cypress woodgrain.
h.
Texture: Mahogany woodgrain.
 
** NOTE TO SPECIFIER ** The following option applies only to Limited Edition. Delete if not required.
 
39.
Exterior Finish: Composite overlays.
 
** NOTE TO SPECIFIER ** Whitewash finish available only on Mahogany overlays. Factory primed finish must be painted or stained in field. Delete option for color not required.
 
a.
Color: Medium Finish.
b.
Color: Dark Finish.
c.
Color: Walnut Finish.
d.
Color: Whitewash Finish.
e.
Color: Primed.
 
** NOTE TO SPECIFIER ** Delete option for texture not required.
 
f.
Texture: Clear Cypress woodgrain.
g.
Texture: Mahogany woodgrain.
 
** NOTE TO SPECIFIER ** The following option applies only to Ultra-Grain. Delete if not required.
 
40.
Exterior Finish: Ultra-Grain Base Door Woodgrain embossed texture with flush design in one of the following color options to simulate the look of stained wood:
 
** NOTE TO SPECIFIER ** Delete color not required.
 
a.
Color: Ultra-Grain Cypress Medium Finish.
b.
Color: Ultra-Grain Cypress Walnut Finish.
 
** NOTE TO SPECIFIER ** The following option applies only to Ultra-Grain. Delete if not required.
 
41.
Exterior Finish: Composite overlays with Clear Cypress woodgrain texture and square edges.
 
** NOTE TO SPECIFIER ** Delete color not required.
 
a.
Color: Medium Finish.
b.
Color: Walnut Finish.
 
** NOTE TO SPECIFIER ** Delete locking type not required.
 
42.
Locking: Standard, non-keyed interior slide bolt.
43.
Locking: Provide optional decorative keyed snap latch lock.
44.
Weatherstripping: Standard, Provide U -shaped bottom seal.
 
** NOTE TO SPECIFIER ** Perimeter seals are optional, choose from manufacturers standard options. Delete if not required.
 
45.
Perimeter Seals: _____.
46.
Tracks: Vertical tracks minimum 0.060 inch (1.524 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.075 inch (1.905 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required.
 
** NOTE TO SPECIFIER ** Delete track type not required.
 
a.
Track Type: Provide standard lift tracks.
b.
Track Type: Provide optional low headroom track.
c.
Track Type: Provide optional high lift track.
d.
Track Type: Provide optional follow-the-roof track.
e.
Track Width: 2 inches (50 mm).
 
** NOTE TO SPECIFIER ** 20 inch and 32 inch radius only available on doors up to 12 ft high. Delete track radius not required.
 
f.
Track Radius: 10 inch (254 mm).
g.
Track Radius: 12 inch (305 mm).
h.
Track Radius: 15 inch (381 mm).
i.
Track Radius: 20 inch (508 mm).
j.
Track Radius: 32 inch (813 mm).
2.12
RESIDENTIAL SECTIONAL DOORS - Modern Steel Collection
A.
Residential Steel Sectional Doors: Modern Steel Collection as manufactured by Clopay Building Products Company
1.
Expanded Polystyrene (EPS) Insulated 1-3/8" (35mm) thick product:
 
** NOTE TO SPECIFIER ** Delete models not required.
 
a.
Flush Model: Clopay Model 4051.
b.
Flush Model: Clopay Model 4132.
c.
Flush Model: Clopay Model 4138.
2.
Expanded Polystyrene (EPS) Insulated 2 inches (51mm) thick product:
a.
Flush Model: Clopay Model 4301.
b.
Flush Model: Clopay Model 4302.
c.
Flush Model: Clopay Model 4308.
d.
Grooved Model: Clopay Model 4305.
e.
Grooved Model: Clopay Model 4309.
3.
Thermally-Broken, Intellicore Polyurethane insulated 1-3/8" (35mm) thick product:
 
** NOTE TO SPECIFIER ** Delete models not required.
 
a.
Flush Model: Clopay Model 9131.
b.
Flush Model: Clopay Model 9132.
c.
Flush Model: Clopay Model 9138.
d.
Grooved Model: Clopay Model 9139.
4.
Thermally-Broken, Intellicore Polyurethane insulated 2 inches (51mm) thick product:
a.
Flush Model: Clopay Model 9201.
b.
Flush Model: Clopay Model 9202.
c.
Flush Model: Clopay Model 9208.
d.
Grooved Model: Clopay Model 9205
e.
Grooved Model: Clopay Model 9209.
5.
Tongue and Groove Flush Models:
a.
Flush Model T40F: 24 Ga. Tongue and Groove Joint Flush Non- Insulated Model.
b.
Flush Model T42F: 24 Ga. Tongue and Groove Joint Flush 1-5/16" insulated Model.
c.
Flush Model T41F: 24 Ga. Tongue and Groove Joint Flush 7/8" insulated Model:
d.
Flush Model T51F: 25 Ga. Tongue and Groove Joint Flush 7/8" insulated Model
6.
Door Construction:
 
** NOTE TO SPECIFIER ** First option applies to models 4051, 4132, 4301, 4302 and 4305. Second option applies to models 9131, 9132, 9201, 9202 and 9205. Delete section not required.
 
a.
Sections (EPS): Pressure bonded expanded polystyrene (EPS) core construction between exterior and interior steel skins.
b.
Sections (Intellicore): Foamed in place Intellicore Polyurethane core construction between exterior and interior steel skins.
c.
Exterior Steel Skins: Formed from flush commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
d.
Interior Steel Skins: Formed from roll formed commercial or drawing quality steel sheet, hot-dip galvanized per ASTM A 924/A 924M and ASTM A 653/A 653M, pre-painted with primer and baked-on polyester topcoat.
e.
Section Joints: Sections formed to create tongue-in-groove meeting joint with thermal break.
f.
Door Stiles: Galvanized steel end stiles and center stiles, pre-punched for easy hinge attachment.
g.
Reinforcing: Galvanized and primed steel reinforcement located under each hinge location, pre-punched for hinge attachment.
h.
Connections: Stiles fastened to steel skins using Tog-L-Loc system.Handles: 2 High impact polymer step plate/lift handles to comply with DASMA 116 and be color-matched to the door sections.
 
** NOTE TO SPECIFIER ** First option applies to models 4051, 4132, 9131, and 9132. Second option applies to models 4301, 4302, 4305, 9201, 9202 and 9205. Delete maximum door size not required.
 
7.
Maximum Door (Size 1-3/8 inch Thick Product): 18 ft (5.5 m) wide by 16 ft (4.9 m) high.
8.
Maximum Door (Size 2 inch Thick Product): 20 ft (6.1 m) wide by 16 ft (4.9 m) high.
9.
Steel Skin Thickness:
 
** NOTE TO SPECIFIER ** Second option applies to color Black and all Ultra-Grain finish options. Delete option not required.
 
a.
Exterior: Minimum 27 gauge 0.016 inch (0.40 mm).
b.
Exterior: Minimum 24 gauge 0.022 inch (.055) mm).
 
** NOTE TO SPECIFIER ** First option applies to models 9131, 9132, 9201, 9202 and 9205. Second option applies to models 4051, 4132, 4301, 4302 and 4305. Delete option for interior not required.
 
c.
Interior: Minimum 29 gauge 0.012 inch (0.30 mm). - Intellicore Doors.
d.
Interior: Minimum 27 gauge 0.015 inch (0.38 mm). - EPS Doors.
10.
End Stiles: Galvanized steel end stiles, engineered for easy hardware attachment through pre-punched holes. Minimum 20 gauge, 0.034 inch (0.86 mm) thick.
11.
Bottom Section: Reinforced with continuous 0.040 inch (1.016 mm) aluminum astragal retainer with U-shaped flexible PVC astragal.
12.
Thermal Resistance: Calculated in accordance with DASMA TDS-163.
 
** NOTE TO SPECIFIER ** First option applies to models 4051, 4138 and 4132. Second option applies to models 4301, 4302, 4308, 4309 and 4305. Third option applies to models 9131, 9138, 9139 and 9132. Fourth option applies to models 9201, 9202, 9208, 9209 and 9205. Delete options not required.
 
a.
EPS 1-3/8 inch (35mm) Thick - R-Value: 6.5 (deg F hr sq ft/Btu.)
b.
EPS 2 inch (51mm) Thick - R-Value: 9.0 (deg F hr sq ft/Btu.)
c.
Intellicore 1-3/8 inch (35mm) Thick - R-Value: 12.9 (deg F hr sq ft/Btu.)
d.
Intellicore 2 inch (51mm) Thick - R-Value: 18.4 (deg F hr sq ft/Btu.)
 
** NOTE TO SPECIFIER ** Delete options for windows not required.
 
13.
Windows: None, doors come standard with no windows.
 
** NOTE TO SPECIFIER ** Delete options for windows not required. Windows below available with Models 4051, 4301, 9131 and 9201. Delete if not required.
 
14.
Optional Windows: Provide optional Decorative Insert Short Panel Windows; injection molded ASA plastic windows measuring 19-1/2 inches x 12 inches (5495 mm x 305 mm).
a.
Glazing: 3/32 inch (2.5 mm) clear SSB glass.
b.
Glazing: 1/8 inch (3 mm) clear DSB glass.
c.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
d.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
e.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
f.
Glazing: 1/8 inch (3 mm) Clear acrylic.
g.
Glazing: 1/8 inch (3 mm) Frosted glass.
h.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
i.
Glazing: 1/8 inch (3 mm) Narrow Reed glass.
j.
Glazing: 1/2 inch (12 mm) insulated Narrow Reed glass.
 
** NOTE TO SPECIFIER ** Delete options for decorative snap-in plastic inserts not required.
 
k.
Decorative Snap-in Plastic Inserts: Sunset 501.
l.
Decorative Snap-in Plastic Inserts: Sunset 502.
m.
Decorative Snap-in Plastic Inserts: Sunset 503.
n.
Decorative Snap-in Plastic Inserts: Sunset 504.
o.
Decorative Snap-in Plastic Inserts: Sunset 505.
p.
Decorative Snap-in Plastic Inserts: Sunset 506.
q.
Decorative Snap-in Plastic Inserts: Charleston 508.
r.
Decorative Snap-in Plastic Inserts: Colonial 509.
s.
Decorative Snap-in Plastic Inserts: Prairie 510.
 
** NOTE TO SPECIFIER ** Windows below available with Model 4301, 9201, and 9131. Delete if not required.
 
15.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows; woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb. impact as per the Florida Building Code) measuring 19-1/2 inches x 12 inches (5495 mm x 305 mm).
a.
Glazing: Clear Polycarbonate.
 
** NOTE TO SPECIFIER ** Delete options for decorative snap-in plastic inserts not required.
 
b.
Decorative Snap-in Plastic Inserts: Sunset 501.
c.
Decorative Snap-in Plastic Inserts: Sunset 502.
d.
Decorative Snap-in Plastic Inserts: Sunset 503.
e.
Decorative Snap-in Plastic Inserts: Sunset 504.
f.
Decorative Snap-in Plastic Inserts: Sunset 505.
g.
Decorative Snap-in Plastic Inserts: Sunset 506.
h.
Decorative Snap-in Plastic Inserts: Charleston 508.
i.
Decorative Snap-in Plastic Inserts: Colonial 509.
j.
Decorative Snap-in Plastic Inserts: Prairie 510.
 
** NOTE TO SPECIFIER ** Windows below available with Models 4051, 4301, 9131 and 9201. Delete if not required.
 
16.
Windows: Provide optional Decorative Short Panel Windows; injection molded ASA plastic windows measuring 19-1/2 inches x 12 inches (5495 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) Carlisle Short, frosted DSB glass, leaded-look.
b.
Glazing: 1/8 inch (3 mm) Kristin Short, frosted DSB glass, leaded-look.
c.
Glazing: 1/8 inch (3 mm) Roselle Short, frosted DSB glass, leaded-look.
d.
Glazing: 1/8 inch (3 mm) Trenton Short, frosted DSB glass, leaded-look.
e.
Glazing: 1/2 inch (12 mm) Carlisle Short, frosted insulated DSB glass, leaded-look.
f.
Glazing: 1/2 inch (12 mm) Kristin Short, frosted insulated DSB glass, leaded-look.
g.
Glazing: 1/2 inch (12 mm) Roselle Short, frosted insulated DSB glass, leaded-look.
h.
Glazing: 1/2 inch (12 mm) Trenton Short, frosted insulated DSB glass, leaded-look.
i.
Glazing: Tuscany Short Wrought Iron, acrylic.
j.
Glazing: Orleans Short Wrought Iron, acrylic.
 
** NOTE TO SPECIFIER ** Windows below available with Models 4051, 4301, 9131 and 9201. Delete if not required.
 
17.
Windows: Provide optional Decorative Insert Long Panel Windows; injection molded ASA plastic windows measuring 40-1/2 inches x 12 inches (1029 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 3/32 inch (2.5 mm) clear SSB glass.
b.
Glazing: 1/8 inch (3 mm) clear DSB glass.
c.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
d.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
e.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
f.
Glazing: 1/8 inch (3 mm) Clear acrylic.
g.
Glazing: 1/8 inch (3 mm) Frosted glass.
h.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
i.
Glazing: 1/8 inch (3 mm) Narrow Reed glass.
j.
Glazing: 1/2 inch (12 mm) insulated Narrow Reed glass.
 
** NOTE TO SPECIFIER ** Delete options for decorative snap-in plastic inserts not required.
 
k.
Decorative Snap-in Plastic Inserts: Sunset 601.
l.
Decorative Snap-in Plastic Inserts: Sunset 603.
m.
Decorative Snap-in Plastic Inserts: Sunset 605.
n.
Decorative Snap-in Plastic Inserts: Charleston 608.
o.
Decorative Snap-in Plastic Inserts: Prairie 610.
p.
Decorative Snap-in Plastic Inserts: Madison 611.
q.
Decorative Snap-in Plastic Inserts: Stockton 612.
r.
Decorative Snap-in Plastic Inserts: Madison Arch 613.
 
** NOTE TO SPECIFIER ** Windows below available with Models 4051, 4301, 9131 and 9201. Delete if not required.
 
18.
Windows: Provide optional Decorative Long Panel Windows; injection molded ASA plastic windows measuring 40-1/2 inches x 12 inches (1029 mm x 305 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) Carlisle Long, frosted DSB glass, leaded-look.
b.
Glazing: 1/8 inch (3 mm) Kristin Long, frosted DSB glass, leaded-look.
c.
Glazing: 1/8 inch (3 mm) Roselle Long, frosted DSB glass, leaded-look.
d.
Glazing: 1/8 inch (3 mm) Trenton Long, frosted DSB glass, leaded-look.
e.
Glazing: 1/2 inch (12 mm) Carlisle Long, frosted insulated DSB glass, leaded-look.
f.
Glazing: 1/2 inch (12 mm) Kristin Long, frosted insulated DSB glass, leaded-look.
g.
Glazing: 1/2 inch (12 mm) Roselle Long, frosted insulated DSB glass, leaded-look.
h.
Glazing: 1/2 inch (12 mm) Trenton Long, frosted insulated DSB glass, leaded-look.
i.
Glazing: Tuscany Long Wrought Iron, acrylic.
j.
Glazing: Orleans Long Wrought Iron, acrylic.
 
NOTE TO SPECIFIER ** Windows below available with Models 4132, 4138, 4302, 4305, 4308, 4309, 9131, 9132, 9138, 9139, 9201, 9202, 9205, 9208, and 9209. Delete if not required.
 
19.
Windows: Provide optional Architectural Series Short Windows; extruded cellular PVC windows measuring 19-1/2 inches x 16 inches (495 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Grilles only available with first four glazing options. Delete if not required.
 
a.
Grilles: Short with square grilles, SQ22.
b.
Grilles: Short with rectangular grilles, REC11.
c.
Grilles: Plain Short, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Narrow Reed glass.
k.
Glazing: 1/2 inch (12 mm) insulated Narrow Reed glass.
l.
Glazing: 1/8 inch (3 mm) Kristin Short, frosted DSB glass, leaded-look.
m.
Glazing: 1/8 inch (3 mm) Trenton Short, frosted DSB glass, leaded-look.
n.
Glazing: 1/8 inch (3 mm) Clayton Short, frosted DSB glass, leaded-look.
o.
Glazing: 1/2 inch (12 mm) Kristin Short, frosted insulated DSB glass, leaded-look.
p.
Glazing: 1/2 inch (12 mm) Trenton Short, frosted insulated DSB glass, leaded-look.
q.
Glazing: 1/2 inch (12 mm) Clayton Short, frosted insulated DSB glass, leaded-look.
r.
Glazing: Wrought Iron Short, acrylic.
 
** NOTE TO SPECIFIER ** Windows below available with Models 4132, 4138, 4302, 4305, 4308, 4309, 9131, 9132, 9138, 9139, 9201, 9202, 9205, 9208, and 9209. Delete if not required
 
20.
Windows: Provide optional Architectural Series Long Windows; extruded cellular PVC windows measuring 42 inches x 16 inches (1067 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Grilles only available with first four glazing options. Delete if not required.
 
a.
Grilles: Long with square grilles, SQ24.
b.
Grilles: Long with rectangular grilles, REC14.
c.
Grilles: Plain Long, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Narrow Reed glass.
k.
Glazing: 1/2 inch (12 mm) insulated Narrow Reed glass.
l.
Glazing: 1/8 inch (3 mm) Kristin Long, frosted DSB glass, leaded-look.
m.
Glazing: 1/8 inch (3 mm) Trenton Long, frosted DSB glass, leaded-look.
n.
Glazing: 1/8 inch (3 mm) Clayton Long, frosted DSB glass, leaded-look.
o.
Glazing: 1/2 inch (12 mm) Kristin Long, frosted insulated DSB glass, leaded-look.
p.
Glazing: 1/2 inch (12 mm) Trenton Long, frosted insulated DSB glass, leaded-look.
q.
Glazing: 1/2 inch (12 mm) Clayton Long, frosted insulated DSB glass, leaded-look.
r.
Glazing: Wrought Iron Long, acrylic.
21.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows, woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb impact as per the Florida Building Code) measuring 19-12 inches x 16 inches (495 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: Clear polycarbonate.
b.
Glazing: Matte polycarbonate.
c.
Glazing: Bronze polycarbonate.
d.
Glazing: Pebbled polycarbonate.
e.
Grilles: Short with square grilles, SQ22.
f.
Grilles: Plain Short, no grilles.
22.
Windows: Provide optional Decorative Insert Series Impact Resistant Windows, woodgrain textured, structurally enhanced window frames (to withstand up to a 350 ft-lb impact as per the Florida Building Code) measuring 42 inches x 16 inches (1067 mm x 406 mm).
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: Clear polycarbonate.
b.
Glazing: Matte polycarbonate.
c.
Glazing: Bronze polycarbonate.
d.
Glazing: Pebbled polycarbonate.
e.
Grilles: Long with square grilles, SQ24.
f.
Grilles: Plain Long, no grilles.
 
** NOTE TO SPECIFIER ** Windows below available with Models 4132, 4138, 4302, 4305, 4308, 4309, 9131, 9132, 9138, 9139, 9201, 9202, 9205, 9208, and 9209. Delete if not required.
 
23.
Windows: Provide optional Architectural Series ARCH1 Windows; extruded cellular PVC windows measuring 42 inches x 16 inches (1067 mm x 406 mm) with a 159-1/2 inches (4051 mm) radius top.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
a.
Glazing: 1/8 inch (3 mm) clear DSB glass.
b.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
c.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
d.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
e.
Glazing: 1/8 inch (3 mm) Frosted glass.
f.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
g.
Glazing: 1/8 inch (3 mm) Narrow Reed glass.
h.
Glazing: 1/2 inch (12 mm) insulated Narrow Reed glass.
 
** NOTE TO SPECIFIER ** Delete grilles not required.
 
i.
Grilles: Snap-in plastic grilles.
j.
Grilles: Vertical grilles.
k.
Grilles: Plain, no grilles.
 
** NOTE TO SPECIFIER ** Windows below available with Models 4132, 4138, 4302, 4305, 4308, 4309, 9131, 9132, 9138, 9139, 9201, 9202, 9205, 9208, and 9209. Delete if not required.
 
24.
Windows: Provide optional Architectural Series ARCH2 Windows; extruded cellular PVC windows measuring 42 inches x 16 inches (1067 mm x 406 mm) with a 39-3/4 inches (1001 mm) radius top.
 
** NOTE TO SPECIFIER ** Delete grilles not required.
 
a.
Grilles: Snap-in plastic grilles.
b.
Grilles: Vertical grilles.
c.
Grilles: Plain, no grilles.
 
** NOTE TO SPECIFIER ** Delete options for glazing not required.
 
d.
Glazing: 1/8 inch (3 mm) clear DSB glass.
e.
Glazing: 1/8 inch (3 mm) obscure DSB glass.
f.
Glazing: 1/2 inch (12 mm) insulated DSB glass.
g.
Glazing: 1/2 inch (12 mm) insulated obscure DSB glass.
h.
Glazing: 1/8 inch (3 mm) Frosted glass.
i.
Glazing: 1/2 inch (12 mm) insulated Frosted glass.
j.
Glazing: 1/8 inch (3 mm) Narrow Reed glass.
k.
Glazing: 1/2 inch (12 mm) insulated Narrow Reed glass.
l.
Glazing: Wrought Iron ARCH, acrylic.
 
** NOTE TO SPECIFIER ** First option below applies only to Models 4302, 4301, 4308, 4305, 4309, 4051, 4132, and 4138. Second option below applies only to Models 9131, 9132, 9201, 9202, 9208, 9209, 9138, and 9139. Delete interior finish not required.
 
25.
Interior Finish: EPS Door- Stucco embossed texture with flush design, white interior color.
26.
Interior Finish: Intellicore Door- Stucco embossed texture with shallow U ribbed pattern.
27.
Exterior Finishes:
 
** NOTE TO SPECIFIER ** First option below applies only to Models 9202, 9201, 9132, 9131, 4302, 4301, 4132, 4051, T42F, T41F, T51F, and T40F. Second option below applies only to Models 9208, 9205, 9209, 9138, 9139, 4308, 4305, 4309, and 4138. Delete exterior finish not required.
 
a.
Finish Type: Woodgrain embossed texture.
b.
Finish Type: Stucco embossed texture.
 
** NOTE TO SPECIFIER ** Hunter Green and Gray not available with Models 9202, 9208, 9205, 9209, 9132, 9138, 9139, 4302, 4308, 4305, 4309, 4132, and 4138. Glacier White and Mocha Brown not available on models 4051. Black not available on 4051. Models T42F, T41F, T51F, and T40F only available in White, Almond, Desert Tan, Sandtone, and Chocolate. Delete colors not required.
 
c.
Color: Standard White.
d.
Color: Almond.
e.
Color: Desert Tan.
f.
Color: Sandtone.
g.
Color: Chocolate.
h.
Color: Bronze.
i.
Color: Hunter Green.
j.
Color: Gray.
k.
Color: Glacier White.
l.
Color: Mocha Brown
m.
Color: Black.
n.
Color: Clopay Color Blast ____.
28.
Ultra-Grain Exterior Finish:
 
** NOTE TO SPECIFIER ** Options only available on Models 9202, 9208, 9205, 9209, 4302, 4308, 4305, 4309. Delete if not required.
 
a.
Finish Type: Ultra-Grain Exterior Finish Woodgrain embossed texture to simulate the look of stained wood.
b.
Finish Type: Ultra-Grain Exterior Finish Woodgrain embossed texture in one of the following color options to simulate the look of stained wood.
 
** NOTE TO SPECIFIER ** Options only available on Models 9202, 9208, 9205, 9209, 4302, 4308, 4305, 4309. Delete color not required.
 
1)
Finish: Ultra-Grain Cypress Medium Finish.
2)
Finish: Ultra-Grain Cypress Cherry Finish.
3)
Finish: Ultra-Grain Cypress Walnut Finish.
 
** NOTE TO SPECIFIER ** Delete locking types not required.
 
29.
Locking: Standard, keyed spring-loaded lock bar.
30.
Locking: Provide optional keyed spring-loaded snap latches.
31.
Locking: Provide optional non-keyed interior slide bolt.
32.
Weatherstripping: Standard, Provide U shaped bottom seal.
 
** NOTE TO SPECIFIER ** Perimeter seals are optional, choose from manufacturers standard options. Delete if not required.
 
33.
Perimeter Seals: _____.
34.
Tracks: Vertical tracks minimum 0.040 inch (1.02 mm) galvanized steel tapered and mounted for wedge type closing. Horizontal tracks minimum 0.051 inch (1.29 mm) galvanized steel, reinforced with minimum 0.0897 inch (2.28 mm) galvanized steel angles as required.
 
** NOTE TO SPECIFIER ** Delete track type not required.
 
a.
Track Type: Provide standard lift tracks.
b.
Track Type: Provide optional low headroom track.
c.
Track Type: Provide optional high lift track.
d.
Track Type: Provide optional follow-the-roof track.
e.
Track Width: 2 inches (50 mm).
 
** NOTE TO SPECIFIER ** 20 inch and 32 inch radius only available on doors up to 12 ft high. Delete track radius not required.
 
f.
Track Radius: 10 inch (254 mm).
g.
Track Radius: 12 inch (305 mm).
h.
Track Radius: 15 inch (381 mm).
i.
Track Radius: 20 inch (508 mm).
j.
Track Radius: 32 inch (813 mm).
PART 3 EXECUTION
 
3.1
EXAMINATION AND PREPARATION
A.
Inspect and prepare substrates and openings for compliance with anchorage requirements using the methods recommended by the manufacturer for achieving best result for the substrates and openings under project conditions. Examine wall and overhead areas, including opening framing and blocking, with installer present, for compliance with requirements for installation tolerances, clearances, and other conditions affecting performance of Work in this Section.
B.
Do not proceed with installation until substrates and opening have been prepared using the methods recommended by the manufacturer and deviations from manufacturer's recommended tolerances and conditions that will be detrimental to the installation are corrected. Commencement of installation constitutes acceptance of conditions.
C.
If preparation is the responsibility of another installer, notify Architect in writing of deviations from manufacturer's recommended installation tolerances and conditions.
3.2
INSTALLATION
A.
Install products in accordance with approved shop drawings and the manufacturer's printed instructions. Install in proper relationship with adjacent construction. Test for proper operation and repeat until satisfactory results are obtained.
3.3
PROTECTION
A.
Protect installed products until completion of project.
B.
Touch-up, repair or replace damaged products before Substantial Completion.
END OF SECTION