Customize this spec with SpecWizard
Download SECTION 11 52 13.50 SURFACE MOUNTED FRONT PROJECTION SCREENS for
WORD | RTF | Text | Word Perfect
Find over 500 more CSI Sections
on Arcat.com
Switch to Masterformat 95
 
SECTION 11 52 13.50
SURFACE MOUNTED FRONT PROJECTION SCREENS
 
 
Copyright 2015 - 2015 ARCAT, Inc. - All rights reserved
** NOTE TO SPECIFIER ** Draper, Inc.; Wall and ceiling surface mounted front projection screens.
This section is based on the products of Draper, Inc., which is located at:
411 S. Pearl P. O. Box 425
Spiceland, IN 47385-0425
Toll Free Tel: 800-238-7999
Tel: 765-987-7999
Fax: 866-637-5611
Email: request info (drapercontract@draperinc.com)
Web: www.draperinc.com
[ Click Here ] for additional information.
Draper manufactures the best and most complete line of projection screens in the world. We want to help you incorporate these screens into the most effective presentation systems. Planning a projection system involves several steps: choosing the screen size, viewing surface, screen model and control system if required. For additional information, see Draper Screen Selection/Resource Center at www.draperinc.com .
 
PART 1 GENERAL
 
1.1
SECTION INCLUDES
 
** NOTE TO SPECIFIER ** Delete items below not required for project.
 
A.
Manually operated, surface mounted, front projection screens.
B.
Electrically operated, surface mounted, front projection screens.
C.
Fixed, surface mounted, projection screen.
1.2
RELATED SECTIONS
 
** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
 
A.
Division 5 - Metal Fabrications: Suspension systems for projection screens.
B.
Section 06 40 00 - Architectural Woodwork.
C.
Section 09 22 26 - Suspension Systems.
D.
Section 09 26 13 - Gypsum Veneer Plastering.
E.
Section 09 21 16.23 - Gypsum Board Shaft Wall Assemblies.
F.
Section 09 51 23 - Acoustical Tile Ceilings.
G.
Division 16 for electrical wiring, connections, and installation of remote control switches for electrically operated projection screens.
1.3
REFERENCES
 
** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
 
A.
NFPA 70 - National Electrical Code.
B.
NFPA 701-99 - Fire Tests for Flame-Resistant Textiles and Films.
C.
GREENGUARD Environmental Institute Gold.
D.
US Green Building Council.
1.4
SUBMITTALS
A.
Submit under provisions of Section 01 30 00 - Administrative Requirements.
B.
Product Data: Manufacturer's data sheets on each product to be used, including:
1.
Preparation instructions and recommendations.
2.
Storage and handling requirements and recommendations.
3.
Installation methods.
 
** NOTE TO SPECIFIER ** Delete below if no electrically operated screens.
 
C.
Wiring diagram for electrically operated units.
 
** NOTE TO SPECIFIER ** Retain below for front projection screens where shop drawings are needed to understand relationships with adjoining work.
 
D.
Shop Drawings: Shop drawings showing layout and types of projection screens. Show the following:
 
** NOTE TO SPECIFIER ** Edit below to suit screens specified and project conditions.
 
1.
Location of screen centerline.
2.
Location of wiring connections.
3.
Seams in viewing surfaces.
4.
Detailed drawings for concealed mounting.
5.
Connections to suspension systems.
6.
Anchorage details.
7.
Accessories.
8.
Frame details.
 
** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.
 
E.
Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.
F.
Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.
1.5
QUALITY ASSURANCE
A.
Single Source Responsibility: Obtain each type of projection screen required from a single manufacturer as a complete unit, including necessary mounting hardware and accessories.
B.
Coordination of Work: Coordinate layout and installation of projection screens with other construction supported by, or penetrating through, ceilings, including light fixtures, HVAC equipment, fire-suppression system, and partitions.
1.6
DELIVERY, STORAGE, AND HANDLING
A.
Do not deliver projection screens until building is enclosed and other construction where screens will be installed is substantially complete.
B.
Store products in manufacturer's unopened packaging until ready for installation.
C.
Protect screens from damage during delivery, handling, storage, and installation.
1.7
COORDINATION
A.
Coordinate work with installation of ceilings, walls, electric service power characteristics, and location.
PART 2 PRODUCTS
 
2.1
MANUFACTURERS
A.
Acceptable Manufacturer: Draper, Inc., which is located at: 411 S. Pearl P. O. Box 425; Spiceland, IN 47385-0425; Toll Free Tel: 800-238-7999; Tel: 765-987-7999; Fax: 866-637-5611; Email: request info (drapercontract@draperinc.com); Web: www.draperinc.com
 
** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
 
B.
Substitutions: Not permitted.
C.
Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.
 
** NOTE TO SPECIFIER ** Delete from the following lists the types of front projection screens not used on the project.
 
2.2
MANUALLY OPERATED, SURFACE MOUNTED, FRONT PROJECTION SCREENS
 
** NOTE TO SPECIFIER ** Delete from the following paragraphs the models of wall and ceiling mounted, manually operated, front projection screens not used on the project.
 
A.
Silhouette/Series M: Spring roller operated, extruded aluminum case. Contoured aluminum case with removable front cover, which conceals all mounting devices and fasteners including viewing surfaces that retract completely inside the case.
1.
System Options:
 
** NOTE TO SPECIFIER ** Select the required case finish and delete two of the following paragraphs.
 
a.
Contoured aluminum case finished in a white color.
b.
Contoured aluminum case finished in a light grey color.
c.
Contoured aluminum case finished in a black color.
 
** NOTE TO SPECIFIER ** If projected mounting brackets are used select the extension required from the following paragraphs and delete the paragraph not used. Delete both paragraphs if projected mounting brackets are not required.
 
d.
Projected Mounting Brackets with a 6 inch (152 mm) clearance from wall.
e.
Projected Mounting Brackets with a 10/14 inch (254/356 mm) clearance from wall.
f.
Wall mount Z-clips.
 
** NOTE TO SPECIFIER **. If projected mounting brackets are used select the finish required from the following paragraphs and delete the paragraph not used. Delete both paragraphs if projected mounting bracket is not required.
 
g.
Projected mounting brackets shall have a white finish.
h.
Projected mounting brackets shall have a black finish.
i.
No projected mounting bracket required.
 
** NOTE TO SPECIFIER ** Select the following auto return paragraph if required and delete if not required.
 
j.
Auto Return spring roller with built-in inertia reduction mechanism to ensure viewing surface retracts slowly, smoothly and quietly into case. Provide intermediate stop positions.
2.
Projection Viewing Surface:
 
** NOTE TO SPECIFIER ** Select the screen type from the following paragraphs and delete those not required. Note that there are size limitations with some viewing surfaces. Contact manufacturer for additional information.
 
a.
Matt White XT1000E - On Axis gain of 1.0. 180 degree viewing cone. Washable surface. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Argent White XH1500E maximum size available is 8 feet by 10 feet (244 cm x 305 cm).
 
b.
Argent White XH1500E - On Axis gain of 1.5. High reflectivity fabric with broad viewing cone. Excellent resolution and color balance. Flame and Mildew resistant.
 
** NOTE TO SPECIFIER ** Pearl White CH1900E maximum size available is 96 inches by 96 inches (244 cm x 244 cm).
 
c.
Pearl White CH1900E - On Axis gain of 1.9. Matt white surface with reflective pearlescent coating.
d.
Contrast Grey XH800E - 0.8 On Axis gain. Smooth grey surface provides excellent resolution and enhances color contrast. 180 degree viewing cone. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Contrast White XH1100E maximum size available is 8 feet by 10 feet (244 cm x 305 cm).
 
e.
Contrast White XH1100E - On Axis gain of 1.1. Diffuse white coating over a grey base material. Recommended for use with low to moderate light output digital projectors, where some provision for light control exists.
 
** NOTE TO SPECIFIER ** ClearSound Perf XT950E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 20 feet (601 cm) from screen.
 
f.
ClearSound Perf XT950E - On Axis gain of 0.95. 180 degree viewing cone. Acoustically transparent. Textile backed matt white perforated surface.
 
** NOTE TO SPECIFIER ** ClearSound White Weave XT900E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
g.
ClearSound White Weave XT900E - On Axis gain of 0.9. 180 degree viewing cone. Acoustically transparent woven blend of fiberglass and PVC. Acoustical properties are comparable to the highest quality speaker grille cloth. Some control of ambient light is recommended. Flame and mildew resistant.
 
** NOTE TO SPECIFIER ** ClearSound Grey Weave XH600E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
h.
ClearSound Grey Weave XH600E - On Axis gain of 0.6. 180 degree viewing cone. Acoustically transparent woven blend of fiberglass and PVC. Grey material for higher contrast. Acoustical properties are comparable to the highest quality speaker grille cloth. Flame and mildew resistant.
i.
Chroma Key Blue - Blue flexible PVC surface for video production where you need the background to "disappear." Matte finish. Flame retardant, tear resistant, and wrinkle resistant. Offers excellent uniformity and consistent surface color edge to edge. Works effectively throughout 180 degree viewable range.
j.
Chroma Key Green - Green flexible PVC surface for video production where you need the background to "disappear." Matte finish. Flame retardant, tear resistant, and wrinkle resistant. Offers excellent uniformity and consistent surface color edge to edge. Works effectively throughout 180 degree viewable range.
 
** NOTE TO SPECIFIER ** Select the screen format and size required for the project. Delete the paragraphs not required.
 
3.
Viewing Area H x W.
a.
NTSC Format (4:3). Black masking borders standard.
1)
6 foot (1.83 m) diagonal, 42-1/2 inches x 56-1/2 inches (1080 mm x 1435 mm).
2)
7 foot (2.13 m) diagonal, 50 inches x 66-1/2 inches (1270 mm x 1689 mm).
3)
100 inch (2540 mm) diagonal, 60 inches x 80 inches (1524 mm x 2032 mm).
4)
10 foot (3.05 m) diagonal, 69 inches x 92 inches (1753 mm x 2337 mm).
b.
HDTV Format (16:9). Black masking borders standard.
1)
65 inch (1651 mm) 31-3/4 inches x 56-1/2 inches (806 mm x 1435 mm).
2)
73 inch (1854 mm) 36 inches x 64 inches (914 mm x 1626 mm).
3)
82 inch (2083 mm) 40-1/2 inches x 72 inches (1029 mm x 1829 mm).
4)
92 inch (2337 mm) diagonal, 45 inches x 80 inches (1143 mm x 2032 mm).
5)
100 inch (2540 mm) diagonal, 49 inches x 87 inches (1245 mm x 2210 mm).
6)
106 inch (2692 mm) diagonal, 52 inches x 92 inches (1321 mm x 2337 mm).
c.
16:10 Format. Black masking borders standard.
1)
67 inch (1702 mm) diagonal, 35-1/4 inches x 56-1/2 inches (895 mm x 1435 mm).
2)
76 inch (1930 mm) diagonal, 40 inches x 64 inches
3)
85 inch (2159 mm) diagonal, 45 inches x 72 inches (1143 mm x 1829 mm).
4)
94 inch (2438 mm) diagonal, 50 inches x 80 inches (1270 mm x 2032 mm).
5)
109 inch (2769 mm) diagonal, 57-1/2 inches x 92 inches (1461 mm x 2337 mm).
 
** NOTE TO SPECIFIER ** If an extra screen drop is required for the project, fill in the drop height and select one of the following paragraphs. Total screen height cannot exceed 8 feet (2.44 m). Select viewing surface color or black. Matching the viewing surface is standard for AV format, black is standard for all other formats. If not required, delete both paragraphs.
 
4.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with top border matching the viewing surface.
5.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with a black masking top border.
B.
Silhouette/Series C: Crank operated, tab tensioned, extruded aluminum case. Wall or ceiling mounted screen system. Contoured aluminum case with removable front cover, which conceals all mounting devices and fasteners including viewing surfaces that retract completely inside the case.
1.
System Options:
 
** NOTE TO SPECIFIER ** Select the required case finish and delete two of the following paragraphs.
 
a.
Contoured aluminum case finished in a white color.
b.
Contoured aluminum case finished in a light grey color.
c.
Contoured aluminum case finished in a black color.
 
** NOTE TO SPECIFIER ** If projected mounting brackets are used select the extension required from the following paragraphs and delete the paragraph not used. Delete both paragraphs if projected mounting brackets are not required.
 
d.
Projected Mounting Brackets with a 6 inch (152 mm) clearance from wall.
e.
Projected Mounting Brackets with a 10/14 inch (254/356 mm) clearance from wall.
f.
Wall mount Z-clips.
 
** NOTE TO SPECIFIER **. If projected mounting brackets are used select the finish required from the following paragraphs and delete the paragraph not used. Delete both paragraphs if projected mounting bracket is not required.
 
g.
Projected mounting brackets shall have a white finish.
h.
Projected mounting brackets shall have a black finish
2.
Projection Viewing Surface:
 
** NOTE TO SPECIFIER ** Select the screen type from the following paragraphs and delete those not required. Note that there are size limitations with some viewing surfaces. Contact manufacturer for additional information.
 
a.
Matt White XT1000V - On Axis gain of 1.0. 180 degree viewing cone. GREENGUARD Gold certified. Available with or without black backing.
b.
Pure White XT1300V - On Axis gain of 1.3. 180 degree viewing cone. For use in situations where lighting is well controlled and where enhanced brightness is needed due to limited projector brightness. Available with or without black backing.
 
** NOTE TO SPECIFIER ** Grey XH600V maximum size available is 9 feet by 12 feet. Available with or without black backing.
 
c.
Grey XH600V - On Axis gain of 0.6. Provides excellent contrast and color reproduction. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Pearl White MH1500V maximum size available is 9 feet by 12 feet (274 cm x 366 cm).
 
d.
Pearl White MH1500V - On Axis gain of 1.5. Matt white surface with reflective pearlescent coating with black backing.
 
** NOTE TO SPECIFIER ** ReAct MS1000V maximum size available is 79 inches by 140 inches (201 cm) x 511 cm).
 
e.
ReAct MS1000V - On Axis gain of 1.0. 60 degree viewing cone. Silver/grey surface provides superior performance in ambient light conditions, offers excellent contrast, optimal color rendition, and is fully HD compliant.
 
** NOTE TO SPECIFIER ** ClearSound NanoPerf XT800V is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
f.
ClearSound NanoPerf XT800V - On Axis gain of 0.8. 180 degree viewing cone. Acoustically transparent white PVC fabric with microscopic perforations.
 
** NOTE TO SPECIFIER ** ClearSound Perf XT900V is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 20 feet (601 cm) from screen.
 
g.
ClearSound Perf XT900V - On Axis gain of 1.0. 180 degree viewing cone. Acoustically transparent. Flexible matt white perforated surface. Reasonable control of ambient light is recommended.
h.
TecVision XH700X Grey - On Axis gain of 0.7. 180 degree viewing cone. Designed for blending applications on curved or flat screens where ambient light is present. Provides very good contrast and color reproduction. Imaging Science Foundation certified and 4K ready. Dark backing.
i.
TecVision XT1100X White - On-Axis gain of 1.1. 180 degree viewing cone. Designed for use when the projector brightness and size of screen require a minimal increase in gain. Imaging Science Foundation certified and 4K ready. Dark backing.
j.
TecVision XH900X Grey - On Axis gain of 0.9. 180 degree viewing cone. Provides very good contrast and color reproduction. Imaging Science Foundation certified. 4K ready. Dark backing.
k.
TecVision MS1000X Grey - On Axis gain of 1.0. 70 degree viewing cone. Provides excellent contrast and color reproduction. Performs well in ambient light. Imaging Science Foundation certified. 4K ready. Dark backing.
l.
TecVision XT1000X White - On Axis gain of 1.0. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready reference screen surface for blending applications, precise resolution, and color accuracy. Dark backing.
m.
TecVision XT1300X White - On Axis gain of 1.3. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready. Dark backing.
n.
TecVision XT1600X White - On Axis gain of 1.6. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready. Dark backing.
o.
TecVision XT1800X White - On Axis gain of 1.8. 180 degree viewing cone. Imaging Science Foundation certified. Suited for active 3D or color combining passive 3D systems. 4K ready. Dark backing.
p.
CineFlex CH1200V - On Axis gain of 1.2. 60 degree viewing cone. Neutral grey rear projection diffusing surface. Provides high resolution and excellent contrast, even in lighted rooms. Recommended for use with low to medium output projectors.
q.
CineFlex XT600V - On Axis gain of 0.6. 180 degree viewing cone. White rear projection surface works well for edge matching or edge blending applications, and also for short throw rear projection. Reasonable control of ambient light is recommended.
r.
CineFlex MH800V - On Axis gain of 0.8. 78 degree viewing cone. Low gain flexible rear material. Designed for use with high light output projectors and wide audience seating patterns.
3.
Tab-Tensioning System:
a.
Viewing surface with integrated tabs and cable on each side of fabric to provide tension and ensure flat viewing surface. Viewing surface and tabs CNC cut as a single piece. Tabs RF welded to the back of viewing surface to prevent tab separation. Tab adhesives are not acceptable. Warranted for 5 years against tab separation
b.
Viewing surface inserted into aluminum bottom dowel.
 
** NOTE TO SPECIFIER ** Select the screen format and size required for the project. Delete the paragraphs not required.
 
4.
Viewing Area H x W.
a.
Custom: Custom Size: ________ H x ____________ W.
b.
NTSC Format (4:3). Black masking borders standard.
1)
6 foot (1.83 m) diagonal, 42-1/2 inches x 56-1/2 inches (1080 mm x 1435 mm).
2)
7 foot (2.13 m) diagonal, 50 inches x 66-1/2 inches (1270 mm x 1689 mm).
3)
100 inch (2540 mm) diagonal, 60 inches x 80 inches (1524 mm x 2032 mm).
4)
10 foot (3.05 m) diagonal, 69 inches x 92 inches (1753 mm x 2337 mm).
c.
HDTV Format (16:9). Black masking borders standard.
1)
92 inch (2337 mm) diagonal, 45 inches x 80 inches (1143 mm x 2032 mm).
2)
106 inch (2692 mm) diagonal, 52 inches x 92 inches (1321 mm x 2337 mm).
 
** NOTE TO SPECIFIER ** If an extra screen drop is required for the project, fill in the drop height and select one of the following paragraphs. Total screen height cannot exceed 8 feet (2.44 m). Select viewing surface color or black. Matching the viewing surface is standard for AV format, black is standard for all other formats. If not required, delete both paragraphs.
 
5.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with top border matching the viewing surface.
6.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with a black masking top border.
C.
Luma 2: Heavy duty, spring roller operated, steel case. Pentagonal, flat back design, steel case with scratch-resistant white textured finish. Universal hanging brackets for attachment to wall or ceiling. Case 22 gauge steel with matching end caps with integral roller brackets.
1.
System Options:
 
** NOTE TO SPECIFIER ** If projected mounting brackets are used select the type required from the following three paragraphs. Select paragraph a. for use with screens through 8 feet wide. Select paragraph d. if projected mounting brackets are not required.
 
a.
Projected Adjustable Mounting Brackets with an 18-1/2 to 24 inch (470 to 610 mm) clearance from wall. White finish.
b.
Fixed Projected Mounting Brackets with a 6 inch (152 mm) clearance from wall. White finish.
c.
Fixed Projected Mounting Brackets with a 10/14 inch (254/356 mm) clearance from wall. White finish.
d.
No projected mounting bracket required.
e.
Floating Mounting Brackets for mounting screen to wall or ceiling.
 
** NOTE TO SPECIFIER ** Delete following paragraph if recessed ceiling installation is not required.
 
f.
Ceiling Trim Kit for recessing above acoustical tile ceiling grid.
 
** NOTE TO SPECIFIER ** Select the auto return paragraph if required and delete if not required.
 
g.
Auto Return spring roller with built-in inertia reduction mechanism to ensure viewing surface retracts slowly, smoothly and quietly into case. Provide intermediate stop positions.
h.
Aluminum Operating Pole:
 
** NOTE TO SPECIFIER ** Select pole required and delete those not required.
 
1)
4 feet.
2)
6 feet.
3)
None.
2.
Projection Viewing Surface:
 
** NOTE TO SPECIFIER ** Select the screen type from the following paragraphs and delete those not required. Note that there are size limitations with some viewing surfaces. Contact manufacturer for additional information.
 
a.
Matt White XT1000E - On Axis gain of 1.0. 180 degree viewing cone. Washable surface. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Argent White XH1500E maximum size available is 8 feet by 10 feet (244 cm x 305 cm).
 
b.
Argent White XH1500E - On Axis gain of 1.5. High reflectivity fabric with broad viewing cone. Excellent resolution and color balance. Flame and Mildew resistant.
 
** NOTE TO SPECIFIER ** Pearl White CH1900E maximum size available is 96 inches by 96 inches (244 cm x 244 cm).
 
c.
Pearl White CH1900E - On Axis gain of 1.9. Matt white surface with reflective pearlescent coating.
d.
Contrast Grey XH800E - 0.8 On Axis gain. Smooth grey surface provides excellent resolution and enhances color contrast. 180 degree viewing cone. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Contrast White XH1100E maximum size available is 8 feet by 10 feet (244 cm x 305 cm).
 
e.
Contrast White XH1100E - On Axis gain of 1.1. Diffuse white coating over a grey base material. Recommended for use with low to moderate light output digital projectors, where some provision for light control exists.
 
** NOTE TO SPECIFIER ** ClearSound Perf XT950E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 20 feet (601 cm) from screen.
 
f.
ClearSound Perf XT950E - On Axis gain of 0.95. 180 degree viewing cone. Acoustically transparent. Textile backed matt white perforated surface.
 
** NOTE TO SPECIFIER ** ClearSound White Weave XT900E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
g.
ClearSound White Weave XT900E - On Axis gain of 0.9. 180 degree viewing cone. Acoustically transparent woven blend of fiberglass and PVC. Acoustical properties are comparable to the highest quality speaker grille cloth. Some control of ambient light is recommended. Flame and mildew resistant.
 
** NOTE TO SPECIFIER ** ClearSound Grey Weave XH600E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
h.
ClearSound Grey Weave XH600E - On Axis gain of 0.6. 180 degree viewing cone. Acoustically transparent woven blend of fiberglass and PVC. Grey material for higher contrast. Acoustical properties are comparable to the highest quality speaker grille cloth. Flame and mildew resistant.
i.
Chroma Key Blue - Blue flexible PVC surface for video production where you need the background to "disappear." Matte finish. Flame retardant, tear resistant, and wrinkle resistant. Offers excellent uniformity and consistent surface color edge to edge. Works effectively throughout 180 degree viewable range.
j.
Chroma Key Green - Green flexible PVC surface for video production where you need the background to "disappear." Matte finish. Flame retardant, tear resistant, and wrinkle resistant. Offers excellent uniformity and consistent surface color edge to edge. Works effectively throughout 180 degree viewable range.
 
** NOTE TO SPECIFIER ** Select the screen format and size required for the project. Delete the paragraphs not required. Note that for sizes 70 inches (1778 mm) high and larger, a pull cord is factory attached.
 
3.
Viewing Area H x W.
a.
Custom: Custom Size: ________ H x ____________ W.
b.
NTSC Format (4:3). Black masking borders standard.
1)
100 inch (2540 mm) diagonal, 60 inches x 80 inches (1524 mm x 2032 mm).
2)
10 foot (3.05 m) diagonal, 69 inches x 92 inches (1753 mm x 2337 mm).
3)
11 foot (3.35 m) diagonal, 78 inches x 104 inches (1981 mm x 2642 mm).
4)
150 inch (3810 mm) diagonal, 87 inches x 116 inches (2210 mm x 3658 mm).
5)
15 foot (4.57 m) diagonal, 105 inches x 140 inches (2667 mm x 3556 mm).
c.
HDTV Format (16:9). Black masking borders standard.
1)
92 inch (2337 mm) diagonal, 45 inches x 80 inches (1143 mm x 2032 mm).
2)
100 inch (2540 mm) diagonal, 49 inches x 87 inches (1245 mm x 2210 mm)
3)
106 inch (2692 mm) diagonal, 52 inches x 92 inches (1321 mm x 2337 mm).
4)
110 inch (2794 mm) diagonal, 54 inches x 96 inches (1372 mm x 2438 mm)
5)
119 inch (3023 mm) diagonal, 58 inches x 104 inches (1473 mm x 2642 mm).
6)
133 inch (3378 mm) diagonal, 65 inches x 116 inches (1651 mm x 2947 mm).
7)
161 inch (4089 mm) diagonal, 79 inches x 140 inches (2007 mm x 3556 mm).
d.
16:10 Format. Black masking borders standard.
1)
94 inch (2438 mm) diagonal, 50 inches x 80 inches (1270 mm x 2032 mm).
2)
109 inch (2769 mm) diagonal, 57-1/2 inches x 92 inches (1461 mm x 2337 mm).
3)
113 inch (2870 mm) diagonal, 60 inches x 96 inches (1524 mm x 2438 mm).
4)
123 inch (3124 mm) diagonal, 65 inches x 104 inches (1351mm x 2642 mm).
5)
137 inch (3480) diagonal, 72-1/2 inches x 116 inches (1842 mm by 2946 mm).
6)
165 inch (4191 mm) diagonal, 87-1/2 inches x 140 inches (2223 mm by 3556 mm).
 
** NOTE TO SPECIFIER ** If an extra screen drop is required for the project, fill in the drop height and one of the following paragraphs and delete the other. Total screen height cannot exceed 12 feet (3.66 m). Select viewing surface color or black. Matching the viewing surface is standard for AV format, black is standard for all other formats. If extra screen drop is not required, delete both paragraphs.
 
4.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with top border matching the viewing surface.
5.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with a black masking top border.
2.3
MOTORIZED, SURFACE MOUNTED, FRONT PROJECTION SCREENS
 
** NOTE TO SPECIFIER ** Delete from the following paragraphs the types of surface mounted, motorized, front projection screens not used on the project.
 
A.
Artisan/Series V: Electric motor operated, hardwood or plastic laminate case, tab tensioned. Wall or ceiling mounted. Housing designed with internal junction box and plug-in wiring connections to allow housing to be installed and connected to building power supply separately from motor and viewing surface.
 
** NOTE TO SPECIFIER ** Select the Hardwood Case style and hardwood case material or the Plastic Laminate case and color from following paragraphs and delete the paragraph not required. Note that hardwood beveled case style increases case height by 1-1/8 inches. Note that plastic laminate is only available in a rectilinear style. If Custom hardwood or laminate is required, define in the space provided.
 
1.
Case Options:
a.
Hardwood Case
1)
Styles.
a)
Radius.
b)
Rectilinear.
c)
Traditional.
d)
Bevel.
2)
Solid Hardwood Case Material.
a)
Natural Maple.
b)
Natural Cherry.
c)
Light Oak.
d)
Medium Oak.
e)
Walnut.
f)
Medium Cherry.
g)
Mahogany.
h)
Custom Wood _________.
b.
Plastic Laminate Case (7/16 inch particleboard, 45 lb. Density, rectilinear styling).
1)
White.
2)
Beige
3)
Dove Grey.
4)
Burgundy.
5)
Black.
6)
Custom Color _________.
 
** NOTE TO SPECIFIER ** Select one of the following motor paragraphs and delete the paragraphs not required. Note that there are size limitations with quiet motors. Contact manufacturer for additional information.
 
2.
Motor mounted inside screen roller on rubber isolation insulators. Motor UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches. Motor with overload protection and electric brake.
3.
Quiet Motor mounted inside screen roller on rubber isolation insulators. Motor operates at 44db and is UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches. Motor with overload protection and electric brake.
 
** NOTE TO SPECIFIER ** Select controls and wall and/or remote-control switches required for project. Delete from the following paragraphs the types of controls and switches not used on the project. Coordinate the compatibility of multiple control selections.
 
4.
Motor Screen Controls, UL certified.
 
** NOTE TO SPECIFIER ** Not compatible with options b, c, d, e, h, i, j, k, or l.
 
a.
Single station control rated 115V AC, 60 Hz with 3-position rocker switch with cover plate to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, c, d, e, h, i, j, k, or l.
 
b.
Multiple station control rated 115V AC, 60 Hz with 3-position rocker switches with cover plates to stop or reverse screen at any point. Automatic override allows only one signal to reach the motor when operated simultaneously
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
c.
Low voltage control unit with three button 24V switches and cover plate to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
d.
Low voltage 24V control unit with hand held RF remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
e.
Low voltage 24V control unit with hand held IR remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options g, h, i, j, k, or l.
 
f.
Key Operated power supply switch to control power to control system.
 
** NOTE TO SPECIFIER ** Not compatible with options d, e, f, h, i, j, k, or l.
 
g.
Locking switch cover plate for limited access to three position switch.
 
** NOTE TO SPECIFIER ** . Not compatible with options a, b, c, d, e, f, g, i, j, k, or l.
 
h.
Key operated 3-position control switch rated 115V AC, 60 Hz to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, f, g, h, j. k, or l.
 
i.
3-position low voltage control switch key locking cover plate rated 24V to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Select one of the following Video Interface Control and delete the remaining. Note that Video Interface Control is not compatible with low voltage control unit. Delete all of the following three paragraphs if video interface control is not required. Not compatible with options a. through j.
 
j.
Video Interface Control for use with equipment with a 115V switched outlet.
k.
Video Interface Control for use with equipment with a 12V switched outlet..
l.
Video Interface Control for use with equipment with a 6V switched outlet.
 
** NOTE TO SPECIFIER ** Left hand motor location is standard. Right hand location is optional (screen will be reverse rolled). Select required paragraph and delete paragraph not required.
 
m.
Motor shall be right mounted (screen will be reverse rolled).
n.
Motor shall be left mounted.
5.
Projection Viewing Surface:
 
** NOTE TO SPECIFIER ** Select the screen type from the following paragraphs and delete those not required. Note that there are size limitations with some viewing surfaces. Contact manufacturer for additional information.
 
a.
Matt White XT1000V - On Axis gain of 1.0. 180 degree viewing cone. GREENGUARD Gold certified. Available with or without black backing.
b.
Pure White XT1300V - On Axis gain of 1.3. 180 degree viewing cone. For use in situations where lighting is well controlled and where enhanced brightness is needed due to limited projector brightness. Available with or without black backing.
 
** NOTE TO SPECIFIER ** Grey XH600V maximum size available is 9 feet by 12 feet. Available with or without black backing.
 
c.
Grey XH600V - On Axis gain of 0.6. Provides excellent contrast and color reproduction. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Pearl White CH1900E maximum size available is 96 inches by 96 inches (244 cm x 244 cm).
 
d.
Pearl White CH1900E - On Axis gain of 1.9. Matt white surface with reflective pearlescent coating.
 
** NOTE TO SPECIFIER ** ReAct MS1000V maximum size available is 79 inches by 140 inches (201 cm x 356 cm).
 
e.
ReAct MS1000V - On Axis gain of 1.0. 60 degree viewing cone. Silver/grey surface provides superior performance in ambient light conditions, offers excellent contrast, optimal color rendition, and is fully HD compliant.
 
** NOTE TO SPECIFIER ** ClearSound NanoPerf XT800V is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
f.
ClearSound NanoPerf XT800V - On Axis gain of 0.8. 180 degree viewing cone. Acoustically transparent white PVC fabric with microscopic perforations.
 
** NOTE TO SPECIFIER ** ClearSound NanoPerf XT900V is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 20 feet (610 cm) from screen.
 
g.
ClearSound Perf XT900V - On Axis gain of 1.0. 180 degree viewing cone. Acoustically transparent. Flexible matt white perforated surface. Reasonable control of ambient light is recommended.
h.
TecVision XH700X Grey - On Axis gain of 0.7. 180 degree viewing cone. Designed for blending applications on curved or flat screens where ambient light is present. Provides very good contrast and color reproduction. Imaging Science Foundation certified and 4K ready. Dark backing.
i.
TecVision XT1100X White - On-Axis gain of 1.1. 180 degree viewing cone. Designed for use when the projector brightness and size of screen require a minimal increase in gain. Imaging Science Foundation certified and 4K ready. Dark backing.
j.
TecVision XH900X Grey - On Axis gain of 0.9. 180 degree viewing cone. Provides very good contrast and color reproduction. Imaging Science Foundation certified. 4K ready. Dark backing.
k.
TecVision MS1000X Grey - On Axis gain of 1.0. 70 degree viewing cone. Provides excellent contrast and color reproduction. Performs well in ambient light. Imaging Science Foundation certified. 4K ready. Dark backing.
l.
TecVision XT1000X White - On Axis gain of 1.0. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready reference screen surface for blending applications, precise resolution, and color accuracy. Dark backing.
m.
TecVision XT1300X White - On Axis gain of 1.3. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready. Dark backing.
n.
TecVision XT1600X White - On Axis gain of 1.6. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready. Dark backing.
o.
TecVision XT1800X White - On Axis gain of 1.8. 180 degree viewing cone. Imaging Science Foundation certified. Suited for active 3D or color combining passive 3D systems. 4K ready. Dark backing.
p.
CineFlex CH1200V - On Axis gain of 1.2. 60 degree viewing cone. Neutral grey rear projection diffusing surface. Provides high resolution and excellent contrast, even in lighted rooms. Recommended for use with low to medium output projectors.
q.
CineFlex XT600V - On Axis gain of 0.6. 180 degree viewing cone. White rear projection surface works well for edge matching or edge blending applications, and also for short throw rear projection. Reasonable control of ambient light is recommended.
r.
CineFlex MH800V - On Axis gain of 0.8. 78 degree viewing cone. Low gain flexible rear material. Designed for use with high light output projectors and wide audience seating patterns.
6.
Tab-Tensioning System:
a.
Viewing surface with integrated tabs and cable on each side of fabric to provide tension and ensure flat viewing surface. Viewing surface and tabs CNC cut as a single piece. Tabs RF welded to the back of viewing surface to prevent tab separation. Tab adhesives are not acceptable. Viewing surface inserted into aluminum bottom dowel. Warranted for 5 years against tab separation.
 
** NOTE TO SPECIFIER ** Select the screen format and size required for the project. Delete the paragraphs not required.
 
7.
Viewing Area H x W.
a.
Custom Size: ________ H x ____________ W.
b.
NTSC Format (4:3). Black masking borders standard.
1)
6 foot (1.83 m) diagonal, 42-1/2 inches x 56-1/2 inches (1080 mm x 1435 mm).
2)
7 foot (2.13 m) diagonal, 50 inches x 66-1/2 inches (1270 mm x 1689 mm).
3)
100 inch (2540 mm) diagonal, 60 inches x 80 inches (1524 mm x 2032 mm).
4)
10 foot (3.05 m) diagonal, 72 inches x 96 inches (1829 mm x 2438 mm).
c.
HDTV Format (16:9). Black masking borders standard.
1)
92 inch (2337 mm) diagonal, 45 inches x 80 inches (1143 mm x 2032 mm).
2)
106 inch (2692 mm) diagonal, 52 inches x 92 inches (1321 mm x 2337 mm).
d.
16:10 Format. Black masking borders standard.
1)
94 inch (2438 mm) diagonal, 50 inches x 80 inches (1270 mm x 2032 mm).
2)
109 inch (2769 mm) diagonal, 57-1/2 inches x 92 inches (1461 mm x 2337 mm).
 
** NOTE TO SPECIFIER ** Edit the following if an extra screen drop exceeding the standard of 12 inches (305 mm) is required for the project. Black is standard for all formats. Note that extra drop will increase the overall length of the case. Select the screen drop type and fill in the drop height from one of the following paragraphs and delete the other. Total screen height cannot exceed 12 feet (3.66 m). If extra screen drop is not required, delete both paragraphs.
 
8.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with top border matching viewing surface color.
9.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with a black masking top border.
B.
Artisan/Series E: Electric motor operated, hardwood or plastic laminate case. Wall or ceiling mounted. Housing designed with internal junction box and plug-in wiring connections to allow housing to be installed and connected to building power supply separately from motor and viewing surface.
 
** NOTE TO SPECIFIER ** Select the Hardwood Case style and hardwood case material or the Plastic Laminate case and color from following paragraphs and delete the paragraph not required. Note that plastic laminate is only available in a rectilinear style. If Custom hardwood or laminate is required, define in the space provided.
 
1.
Case Options:
a.
Hardwood Case
1)
Styles.
a)
Radius.
b)
Rectilinear.
c)
Traditional.
d)
Bevel.
2)
Solid Hardwood Case Material.
a)
Natural Maple.
b)
Natural Cherry.
c)
Light Oak.
d)
Medium Oak.
e)
Walnut.
f)
Medium Cherry.
g)
Mahogany.
h)
Custom Wood _________.
b.
Plastic Laminate Case (7/16 inch particleboard, 45 lb. Density, rectilinear styling).
1)
White.
2)
Beige
3)
Dove Grey.
4)
Burgundy.
5)
Black.
6)
Custom Color _________.
 
** NOTE TO SPECIFIER ** Select one of the following motor paragraphs and delete the paragraph not required. Note that there are size limitations with quiet motors. Contact manufacturer for additional information.
 
2.
Motor mounted inside screen roller on rubber isolation insulators. Motor UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches.
3.
Quiet Motor mounted inside screen roller on rubber isolation insulators. Motor operates at 44db and is UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches.
 
** NOTE TO SPECIFIER ** Select controls and wall and/or remote-control switches required for project. Delete from the following paragraphs the types of controls and switches not used on the project. Coordinate the compatibility of multiple control selections.
 
4.
Motor Screen Controls, UL certified.
 
** NOTE TO SPECIFIER ** Not compatible with options b, c, d, e, h, i, j, k, or l.
 
a.
Single station control rated 115V AC, 60 Hz with 3-position rocker switch with cover plate to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, c, d, e, h, i, j, k, or l.
 
b.
Multiple station control rated 115V AC, 60 Hz with 3-position rocker switches with cover plates to stop or reverse screen at any point. Automatic override allows only one signal to reach the motor when operated simultaneously
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
c.
Low voltage control unit with three button 24V switches and cover plate to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
d.
Low voltage 24V control unit with hand held RF remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
e.
Low voltage 24V control unit with hand held IR remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options g, h, i, j, k, or l.
 
f.
Key Operated power supply switch to control power to control system.
 
** NOTE TO SPECIFIER ** Not compatible with options d, e, f, h, i, j, k, or l.
 
g.
Locking switch cover plate for limited access to three position switch.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, c, d, e, f, g, i, j, k, or l.
 
h.
Key operated 3-position control switch rated 115V AC, 60 Hz to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, f, g, h, j, k, or l.
 
i.
3-position low voltage control switch with key locking cover plate rated 24V to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Select one of the following Video Interface Control and delete the remaining. Note that Video Interface Control is not compatible with low voltage control unit. Delete all of the following three paragraphs if video interface control is not required. Not compatible with options a. through j.
 
j.
Video Interface Control for use with equipment with a 115V switched outlet.
k.
Video Interface Control for use with equipment with a 12V switched outlet..
l.
Video Interface Control for use with equipment with a 6V switched outlet.
 
** NOTE TO SPECIFIER ** Left hand motor location is standard. Right hand location is optional (screen will be reverse rolled). Select required paragraph and delete paragraph not required.
 
m.
Motor shall be right mounted (screen will be reverse rolled).
n.
Motor shall be left mounted.
5.
Projection Viewing Surface:
 
** NOTE TO SPECIFIER ** Select the screen type from the following paragraphs and delete those not required. Note that there are size limitations with some viewing surfaces. Contact manufacturer for additional information.
 
a.
Matt White XT1000E - On Axis gain of 1.0. 180 degree viewing cone. Washable surface. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Argent White XH1500E maximum size available is 8 feet by 10 feet (244 cm x 305 cm).
 
b.
Argent White XH1500E - On Axis gain of 1.5. High reflectivity fabric with broad viewing cone. Excellent resolution and color balance. Flame and Mildew resistant.
 
** NOTE TO SPECIFIER ** Pearl White CH1900E maximum size available is 96 inches by 96 inches (244 cm x 244 cm).
 
c.
Pearl White CH1900E - On Axis gain of 1.9. Matt white surface with reflective pearlescent coating.
d.
Contrast Grey XH800E - 0.8 On Axis gain. Smooth grey surface provides excellent resolution and enhances color contrast. 180 degree viewing cone. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Contrast White XH1100E maximum size available is 8 feet by 10 feet (244 cm x 305 cm)
 
e.
Contrast White XH1100E - On Axis gain of 1.1. Diffuse white coating over a grey base material. Recommended for use with low to moderate light output digital projectors, where some provision for light control exists.
 
** NOTE TO SPECIFIER ** ClearSound Perf XT950E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 20 feet (601 cm) from screen.
 
f.
ClearSound Perf XT950E - On Axis gain of 0.95. 180 degree viewing cone. Acoustically transparent. Textile backed matt white perforated surface.
 
** NOTE TO SPECIFIER ** ClearSound White Weave XT900E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
g.
ClearSound White Weave XT900E - On Axis gain of 0.9. 180 degree viewing cone. Acoustically transparent woven blend of fiberglass and PVC. Acoustical properties are comparable to the highest quality speaker grille cloth. Some control of ambient light is recommended. Flame and mildew resistant.
 
** NOTE TO SPECIFIER ** ClearSound Grey Weave XH600E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
h.
ClearSound Grey Weave XH600E - On Axis gain of 0.6. 180 degree viewing cone. Acoustically transparent woven blend of fiberglass and PVC. Grey material for higher contrast. Acoustical properties are comparable to the highest quality speaker grille cloth. Flame and mildew resistant.
i.
Chroma Key Blue - Blue flexible PVC surface for video production where you need the background to "disappear." Matte finish. Flame retardant, tear resistant, and wrinkle resistant. Offers excellent uniformity and consistent surface color edge to edge. Works effectively throughout 180 degree viewable range.
j.
Chroma Key Green - Green flexible PVC surface for video production where you need the background to "disappear." Matte finish. Flame retardant, tear resistant, and wrinkle resistant. Offers excellent uniformity and consistent surface color edge to edge. Works effectively throughout 180 degree viewable range.
 
** NOTE TO SPECIFIER ** Select the screen format and size required for the project. Delete the paragraphs not required.
 
6.
Viewing Area H x W.
a.
Custom Size: ________ H x ____________ W.
b.
NTSC Format (4:3). Black masking borders standard.
1)
6 foot (1.83 m) diagonal, 42-1/2 inches x 56-1/2 inches (1080 mm x 1435 mm).
2)
7 foot (2.13 m) diagonal, 50 inches x 66-1/2 inches (1270 mm x 1689 mm).
3)
100 inch (2540 mm) diagonal, 60 inches x 80 inches (1524 mm x 2032 mm).
4)
10 foot (3.05 m) diagonal, 69 inches x 92 inches (1753 mm x 2337 mm).
c.
HDTV Format (16:9). Black masking borders standard.
1)
92 inch (2337 mm) diagonal, 45 inches x 80 inches (1143 mm x 2032 mm).
2)
106 inch (2692 mm) diagonal, 52 inches x 92 inches (1321 mm x 2337 mm).
d.
16:10 Format. Black masking borders standard.
1)
94 inch (2438 mm) diagonal, 50 inches x 80 inches (1270 mm x 2032 mm).
2)
109 inch (2769 mm) diagonal, 57-1/2 inches x 92 inches (1461 mm x 2337 mm).
 
** NOTE TO SPECIFIER ** If an extra screen drop is required for the project, fill in the drop height and select one of the following paragraphs. Total screen height cannot exceed 8 feet (2.44 m). Select viewing surface color or black. Matching the viewing surface is standard for AV format, black is standard for all other formats. If not required, delete both paragraphs.
 
7.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with top border matching the viewing surface.
8.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with a black masking top border.
C.
Silhouette/Series V: Electric motor operated, extruded aluminum case, tab tensioned. Wall or ceiling mounted. Contoured aluminum case with removable front cover, which conceals all mounting devices and fasteners including viewing surfaces that retract completely inside the case.
 
** NOTE TO SPECIFIER ** Select one of the following motor paragraphs and delete the paragraph not required. Note that there are size limitations with quiet motors. Contact manufacturer for additional information.
 
1.
Motor mounted inside screen roller on rubber isolation insulators. Motor UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches.
2.
Quiet Motor mounted inside screen roller on rubber isolation insulators. Motor operates at 44db and is UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches.
 
** NOTE TO SPECIFIER ** Select controls and wall and/or remote-control switches required for project. Delete from the following paragraphs the types of controls and switches not used on the project. Coordinate the compatibility of multiple control selections.
 
3.
Motor Screen Controls, UL certified.
 
** NOTE TO SPECIFIER ** Not compatible with options b, c, d, e, h, i, j, k, or l.
 
a.
Single station control rated 115V AC, 60 Hz with 3-position rocker switch with cover plate to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, c, d, e, h, i, j, k, or l.
 
b.
Multiple station control rated 115V AC, 60 Hz with 3-position rocker switches with cover plates to stop or reverse screen at any point. Automatic override allows only one signal to reach the motor when operated simultaneously
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
c.
Low voltage control unit with three button 24V switches and cover plate to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
d.
Low voltage 24V control unit with hand held RF remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
e.
Low voltage 24V control unit with hand held IR remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options g, h, i, j, k, or l.
 
f.
Key Operated power supply switch to control power to control system.
 
** NOTE TO SPECIFIER ** Not compatible with options d, e, f, h, i, j, k, or l.
 
g.
Locking switch cover plate for limited access to three position switch.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, c, d, e, f, g, i, j, k, or l.
 
h.
Key operated 3-position control switch rated 115V AC, 60 Hz to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, f, g, h, j, k, or l.
 
i.
3-position low voltage control switch with key locking cover plate rated 24V to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Select one of the following Video Interface Control and delete the remaining. Note that Video Interface Control is not compatible with low voltage control unit. Delete all of the following three paragraphs if video interface control is not required. Not compatible with options a. through j.
 
j.
Video Interface Control for use with equipment with a 115V switched outlet.
k.
Video Interface Control for use with equipment with a 12V switched outlet..
l.
Video Interface Control for use with equipment with a 6V switched outlet.
 
** NOTE TO SPECIFIER ** Left hand motor location is standard. Right hand location is optional (screen will be reverse rolled). Select required paragraph and delete paragraph not required.
 
m.
Motor shall be right mounted (screen will be reverse rolled).
n.
Motor shall be left mounted.
4.
System Options:
 
** NOTE TO SPECIFIER ** Select the required case finish and delete two of the following paragraphs.
 
a.
Contoured aluminum case finished in a white color.
b.
Contoured aluminum case finished in a light grey color.
c.
Contoured aluminum case finished in a black color.
 
** NOTE TO SPECIFIER ** If projected mounting brackets are used select the extension required from the following paragraphs and delete the paragraph not used. Delete both paragraphs if projected mounting brackets are not required.
 
d.
Projected Mounting Brackets with a 6 inch (152 mm) clearance from wall.
e.
Projected Mounting Brackets with a 10/14 inch (254/356 mm) clearance from wall.
f.
Wall Mount: Z-clip.
 
** NOTE TO SPECIFIER **. If projected mounting brackets are used select the finish required from the following paragraphs and delete the paragraph not used. Delete both paragraphs if projected mounting bracket is not required.
 
g.
Projected mounting brackets shall have a white finish.
h.
Projected mounting brackets shall have a black finish
5.
Projection Viewing Surface:
 
** NOTE TO SPECIFIER ** Select the screen type from the following paragraphs and delete those not required. Note that there are size limitations with some viewing surfaces. Contact manufacturer for additional information.
 
a.
Matt White XT1000V - On Axis gain of 1.0. 180 degree viewing cone. GREENGUARD Gold certified. Available with or without black backing.
b.
Pure White XT1300V - On Axis gain of 1.3. 180 degree viewing cone. For use in situations where lighting is well controlled and where enhanced brightness is needed due to limited projector brightness. Available with or without black backing.
 
** NOTE TO SPECIFIER ** Grey XH600V maximum size available is 9 feet by 12 feet (274 cm x 366 cm).
 
c.
Grey XH600V - On Axis gain of 0.6. Provides excellent contrast and color reproduction. GREENGUARD Gold certified. Available with or without black backing.
 
** NOTE TO SPECIFIER ** Pearl White CH1900E maximum size available is 96 inches by 96 inches (244 cm x 244 cm).
 
d.
Pearl White CH1900E - On Axis gain of 1.9. Matt white surface with reflective pearlescent coating.
 
** NOTE TO SPECIFIER ** ReAct MS1000V maximum size available is 79 inches by 140 inches (201 cm x 356 cm).
 
e.
ReAct MS1000V - On Axis gain of 1.0. 60 degree viewing cone. Silver/grey surface provides superior performance in ambient light conditions, offers excellent contrast, optimal color rendition, and is fully HD compliant.
 
** NOTE TO SPECIFIER ** ClearSound NanoPerf XT800V is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
f.
ClearSound NanoPerf XT800V - On Axis gain of 0.8. 180 degree viewing cone. Acoustically transparent white PVC fabric with microscopic perforations.
 
** NOTE TO SPECIFIER ** ClearSound NanoPerf XT900V is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 20 feet (610 cm) from screen.
 
g.
ClearSound Perf XT900V - On Axis gain of 1.0. 180 degree viewing cone. Acoustically transparent. Flexible matt white perforated surface. Reasonable control of ambient light is recommended.
h.
TecVision XH700X Grey - On Axis gain of 0.7. 180 degree viewing cone. Designed for blending applications on curved or flat screens where ambient light is present. Provides very good contrast and color reproduction. Imaging Science Foundation certified and 4K ready.
i.
TecVision XT1100X White - On-Axis gain of 1.1. 180 degree viewing cone. Designed for use when the projector brightness and size of screen require a minimal increase in gain. Imaging Science Foundation certified and 4K ready.
j.
TecVision XH900X Grey - On Axis gain of 0.9. 180 degree viewing cone. Provides very good contrast and color reproduction. Imaging Science Foundation certified. 4K ready. Dark backing.
k.
TecVision MS1000X Grey - On Axis gain of 1.0. 70 degree viewing cone. Provides excellent contrast and color reproduction. Performs well in ambient light. Imaging Science Foundation certified. 4K ready. Dark backing.
l.
TecVision XT1000X White - On Axis gain of 1.0. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready reference screen surface for blending applications, precise resolution, and color accuracy. Dark backing.
m.
TecVision XT1300X White - On Axis gain of 1.3. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready. Dark backing.
n.
TecVision XT1600X White - On Axis gain of 1.6. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready. Dark backing.
o.
TecVision XT1800X White - On Axis gain of 1.8. 180 degree viewing cone. Imaging Science Foundation certified. Suited for active 3D or color combining passive 3D systems. 4K ready. Dark backing.
p.
CineFlex CH1200V - On Axis gain of 1.2. 60 degree viewing cone. Neutral grey rear projection diffusing surface. Provides high resolution and excellent contrast, even in lighted rooms. Recommended for use with low to medium output projectors.
q.
CineFlex XT600V - On Axis gain of 0.6. 180 degree viewing cone. White rear projection surface works well for edge matching or edge blending applications, and also for short throw rear projection. Reasonable control of ambient light is recommended.
r.
CineFlex MH800V - On Axis gain of 0.8. 78 degree viewing cone. Low gain flexible rear material. Designed for use with high light output projectors and wide audience seating patterns.
6.
Tab-Tensioning System:
a.
Viewing surface with integrated tabs and cable on each side of fabric to provide tension and ensure flat viewing surface. Viewing surface and tabs CNC cut as a single piece. Tabs RF welded to the back of viewing surface to prevent tab separation. Tab adhesives are not acceptable. Viewing surface inserted into aluminum bottom dowel. Warranted for 5 years against tab separation.
 
** NOTE TO SPECIFIER ** Select the screen format and size required for the project. Delete the paragraphs not required.
 
7.
Viewing Area H x W.
a.
Custom Size: ________ H x ____________ W.
b.
NTSC Format (4:3). Black masking borders standard.
1)
6 foot (1.83 m) diagonal, 42-1/2 inches x 56-1/2 inches (1080 mm x 1435 mm).
2)
7 foot (2.13 m) diagonal, 50 inches x 66-1/2 inches (1270 mm x 1689 mm).
3)
100 inch (2540 mm) diagonal, 60 inches x 80 inches (1524 mm x 2032 mm).
4)
10 foot (3.05 m) diagonal, 69 inches x 92 inches (1753 mm x 2337 mm).
c.
HDTV Format (16:9). Black masking borders standard.
1)
65 inch (1651 mm) 31-3/4 inches x 56-1/2 inches (806 mm x 1435 mm).
2)
73 inch (1854 mm) 36 inches x 64 inches (914 mm x 1626 mm).
3)
82 inch (2083 mm) 40-1/2 inches x 72 inches (1029 mm x 1829 mm).
4)
92 inch (2337 mm) diagonal, 45 inches x 80 inches (1143 mm x 2032 mm).
5)
100 inch (2540 mm) diagonal, 49 inches x 87 inches (1245 mm x 2210 mm)
6)
106 inch (2692 mm) diagonal, 52 inches x 92 inches (1321 mm x 2337 mm).
7)
110 inch (2794 mm) diagonal, 54 inches x 96 inches (1372 mm x 2438 mm)
d.
16:10 Format. Black masking borders standard.
1)
67 inch (1702 mm) diagonal, 35-1/4 inches x 56-1/2 inches (895 mm x 1435 mm).
2)
76 inch (1930 mm) diagonal, 40 inches x 64 inches
3)
85 inch (2159 mm) diagonal, 45 inches x 72 inches (1143 mm x 1829 mm).
4)
94 inch (2438 mm) diagonal, 50 inches x 80 inches (1270 mm x 2032 mm).
5)
109 inch (2769 mm) diagonal, 57-1/2 inches x 92 inches (1461 mm x 2337 mm).
6)
113 inch (2870 mm) diagonal, 60 inches x 96 inches (1524 mm x 2438 mm).
 
** NOTE TO SPECIFIER ** If an extra screen drop is required for the project, fill in the drop height and select one of the following paragraphs. Total screen height cannot exceed 8 feet (2.44 m). Select viewing surface color or black. Matching the viewing surface is standard for AV format, black is standard for all other formats. If not required, delete both paragraphs.
 
8.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with top border matching the viewing surface.
9.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with a black masking top border.
D.
Silhouette/Series E: Electric motor operated, extruded aluminum case. Contoured aluminum case with removable front cover, which conceals all mounting devices and fasteners including viewing surfaces that retract completely inside the case.
 
** NOTE TO SPECIFIER ** Select one of the following motor paragraphs and delete the paragraph not required. Note that there are size limitations with quiet motors. Contact manufacturer for additional information.
 
1.
Motor mounted inside screen roller on rubber isolation insulators. Motor UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches.
2.
Quiet Motor mounted inside screen roller on rubber isolation insulators. Motor operates at 44db and is UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches.
 
** NOTE TO SPECIFIER ** Select controls and wall and/or remote-control switches required for project. Delete from the following paragraphs the types of controls and switches not used on the project. Coordinate the compatibility of multiple control selections.
 
3.
Motor Screen Controls, UL certified.
 
** NOTE TO SPECIFIER ** Not compatible with options b, c, d, e, h, i, j, k, or l.
 
a.
Single station control rated 115V AC, 60 Hz with 3-position rocker switch with cover plate to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, c, d, e, h, i, j, k, or l.
 
b.
Multiple station control rated 115V AC, 60 Hz with 3-position rocker switches with cover plates to stop or reverse screen at any point. Automatic override allows only one signal to reach the motor when operated simultaneously
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
c.
Low voltage control unit with three button 24V switches and cover plate to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** . Not compatible with options a, b, g, h, j, k, or l.
 
d.
Low voltage 24V control unit with hand held RF remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
e.
Low voltage 24V control unit with hand held IR remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options g, h, i, j, k, or l.
 
f.
Key Operated power supply switch to control power to control system.
 
** NOTE TO SPECIFIER ** Not compatible with options d, e, f, h, i, j, k, or l.
 
g.
Locking switch cover plate for limited access to three position switch.
 
** NOTE TO SPECIFIER ** . Not compatible with options a, b, c, d, e, f, g, i, j, k, or l.
 
h.
Key operated 3-position control switch rated 115V AC, 60 Hz to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, f, g, h, j, k, or l.
 
i.
3-position low voltage control switch with key locking cover plate rated 24V to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Select one of the following Video Interface Control and delete the remaining. Note that Video Interface Control is not compatible with low voltage control unit. Delete all of the following three paragraphs if video interface control is not required. Not compatible with options a. through j.
 
j.
Video Interface Control for use with equipment with a 115V switched outlet.
k.
Video Interface Control for use with equipment with a 12V switched outlet..
l.
Video Interface Control for use with equipment with a 6V switched outlet.
 
** NOTE TO SPECIFIER ** Left hand motor location is standard. Right hand location is optional (screen will be reverse rolled). Select required paragraph and delete paragraph not required.
 
m.
Motor shall be right mounted (screen will be reverse rolled).
n.
Motor shall be left mounted.
4.
System Options:
 
** NOTE TO SPECIFIER ** Select the required case finish and delete two of the following paragraphs.
 
a.
Contoured aluminum case finished in a white color.
b.
Contoured aluminum case finished in a light grey color.
c.
Contoured aluminum case finished in a black color.
 
** NOTE TO SPECIFIER ** If projected mounting brackets are used select the extension required from the following paragraphs and delete the paragraph not used. Delete both paragraphs if projected mounting brackets are not required.
 
d.
Projected Mounting Brackets with a 6 inch (152 mm) clearance from wall.
e.
Projected Mounting Brackets with a 10 to 14 inch (254 to 356 mm) clearance from wall.
 
** NOTE TO SPECIFIER **. If projected mounting brackets are used select the finish required from the following paragraphs and delete the paragraph not used. Delete both paragraphs if projected mounting bracket is not required.
 
f.
Projected mounting brackets shall have a white finish.
g.
Projected mounting brackets shall have a black finish
5.
Projection Viewing Surface:
 
** NOTE TO SPECIFIER ** Select the screen type from the following paragraphs and delete those not required. Note that there are size limitations with some viewing surfaces. Contact manufacturer for additional information.
 
a.
Matt White XT1000E - On Axis gain of 1.0. 180 degree viewing cone. Washable surface. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Argent White XH1500E maximum size available is 8 feet by 10 feet (244 cm x 305 cm).
 
b.
Argent White XH1500E - On Axis gain of 1.5. High reflectivity fabric with broad viewing cone. Excellent resolution and color balance. Flame and Mildew resistant.
 
** NOTE TO SPECIFIER ** Pearl White CH1900E maximum size available is 96 inches by 96 inches (244 cm x 244 cm).
 
c.
Pearl White CH1900E - On Axis gain of 1.9. Matt white surface with reflective pearlescent coating.
d.
Contrast Grey XH800E - 0.8 On Axis gain. Smooth grey surface provides excellent resolution and enhances color contrast. 180 degree viewing cone. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Contrast White XH1100E maximum size available is 8 feet by 10 feet (244 cm x 305 cm).
 
e.
Contrast White XH1100E - On Axis gain of 1.1. Diffuse white coating over a grey base material. Recommended for use with low to moderate light output digital projectors, where some provision for light control exists.
 
** NOTE TO SPECIFIER ** ClearSound Perf XT950E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 20 feet (601 cm) from screen.
 
f.
ClearSound Perf XT950E - On Axis gain of 0.95. 180 degree viewing cone. Acoustically transparent. Textile backed matt white perforated surface.
 
** NOTE TO SPECIFIER ** ClearSound White Weave XT900E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
g.
ClearSound White Weave XT900E - On Axis gain of 0.9. 180 degree viewing cone. Acoustically transparent woven blend of fiberglass and PVC. Acoustical properties are comparable to the highest quality speaker grille cloth. Some control of ambient light is recommended. Flame and mildew resistant.
 
** NOTE TO SPECIFIER ** ClearSound Grey Weave XH600E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
h.
ClearSound Grey Weave XH600E - On Axis gain of 0.6. 180 degree viewing cone. Acoustically transparent woven blend of fiberglass and PVC. Grey material for higher contrast. Acoustical properties are comparable to the highest quality speaker grille cloth. Flame and mildew resistant.
i.
Chroma Key Blue - Blue flexible PVC surface for video production where you need the background to "disappear." Matte finish. Flame retardant, tear resistant, and wrinkle resistant. Offers excellent uniformity and consistent surface color edge to edge. Works effectively throughout 180 degree viewable range.
j.
Chroma Key Green - Green flexible PVC surface for video production where you need the background to "disappear." Matte finish. Flame retardant, tear resistant, and wrinkle resistant. Offers excellent uniformity and consistent surface color edge to edge. Works effectively throughout 180 degree viewable range.
 
** NOTE TO SPECIFIER ** Select the screen format and size required for the project. Delete the paragraphs not required.
 
6.
Viewing Area H x W.
a.
Custom Size: ________ H x ____________ W.
b.
NTSC Format (4:3). Black masking borders standard.
1)
6 foot (1.83 m) diagonal, 42-1/2 inches x 56-1/2 inches (1080 mm x 1435 mm).
2)
7 foot (2.13 m) diagonal, 50 inches x 66-1/2 inches (1270 mm x 1689 mm).
3)
100 inch (2540 mm) diagonal, 60 inches x 80 inches (1524 mm x 2032 mm).
4)
10 foot (3.05 m) diagonal, 69 inches x 92 inches (1753 mm x 2337 mm).
c.
HDTV Format (16:9). Black masking borders standard.
1)
65 inch (1651 mm) diagonal, 31.75 inches x 56.5 inches (808 mm x 1435 mm).
2)
73 inch (1854 mm) diagonal, 36 x 64 inches (914 mm x 1626 mm)
3)
82 inch (2083 mm) diagonal, 40.5 inches x 72 inches (1029 mm x 1829 mm).
4)
92 inch (2337 mm) diagonal, 45 inches x 80 inches (1143 mm x 2032 mm).
5)
100 inch (2540 mm) diagonal, 49 inches x 87 inches (1245 mm x 2210 mm)
6)
106 inch (2692 mm) diagonal, 52 inches x 92 inches (1321 mm x 2337 mm).
7)
110 inch (2794 mm) diagonal, 54 inches x 96 inches (1372 mm x 2438 mm)
d.
16:10 Format. Black masking borders standard.
1)
67 inch (1702 mm) diagonal, 35-1/4 inches x 56-1/2 inches (895 mm x 1435 mm).
2)
76 inch (1930 mm) diagonal, 40 inches x 64 inches
3)
85 inch (2159 mm) diagonal, 45 inches x 72 inches (1143 mm x 1829 mm).
4)
94 inch (2438 mm) diagonal, 50 inches x 80 inches (1270 mm x 2032 mm).
5)
109 inch (2769 mm) diagonal, 57-1/2 inches x 92 inches (1461 mm x 2337 mm).
6)
113 inch (2870 mm) diagonal, 60 inches x 96 inches (1524 mm x 2438 mm).
 
** NOTE TO SPECIFIER ** If an extra screen drop is required for the project, fill in the drop height and select one of the following paragraphs. Total screen height cannot exceed 8 feet (2.44 m). Select viewing surface color or black. Matching the viewing surface is standard for AV format, black is standard for all other formats. If not required, delete both paragraphs.
 
7.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with top border matching the viewing surface.
8.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with a black masking top border.
E.
Premier: Electric motor operated, pentagonal-shaped steel case, tab tensioned. Metal roller mounted on rubber isolation mounts. Case for sizes through 12 feet x 12 feet AV, 200 inch NTSC, 184 inch HDTV and 189 inch 16:10, is one piece 22 gauge steel with end caps forming universal wall or ceiling hanging bracket. Case for sizes above 12 feet x 12 feet AV, 200 inch NTSC, 184 inch HDTV and 189 inch 16:10, consists of a curved front and L-shaped back/top cover fabricated of extruded aluminum, with endcaps forming ceiling hanging bracket. Case and tensioning dowel finished in flat black.
 
** NOTE TO SPECIFIER ** Select one of the following motor paragraphs and the related control option as required. Delete the paragraphs not required. Note that there are size limitations with quiet motors. Contact manufacturer for additional information.
 
1.
Motor mounted inside screen roller on rubber isolation insulators. Motor UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches.
2.
Quiet Motor mounted inside screen roller on rubber isolation insulators. Motor operates at 44db and is UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches.
 
** NOTE TO SPECIFIER ** Select one of the following four motor paragraphs and the related control option as required. Delete the paragraphs not required. Note that there are size limitations with quiet motors. Contact manufacturer for additional information.
 
3.
Motor Screen Controls, UL certified.
 
** NOTE TO SPECIFIER ** Not compatible with options b, c, d, e, h, i, j, k, or l.
 
a.
Single station control rated 115V AC, 60 Hz with 3-position rocker switch with cover plate to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, c, d, e, h, i, j, k, or l.
 
b.
Multiple station control rated 115V AC, 60 Hz with 3-position rocker switches with cover plates to stop or reverse screen at any point. Automatic override allows only one signal to reach the motor when operated simultaneously
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
c.
Low voltage control unit with three button 24V switches and cover plate to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
d.
Low voltage 24V control unit with hand held RF remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
e.
Low voltage 24V control unit with hand held IR remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options g, h, i, j, k, or l.
 
f.
Key Operated power supply switch to control power to control system.
 
** NOTE TO SPECIFIER ** Not compatible with options d, e, f, h, i, j, k, or l.
 
g.
Locking switch cover plate for limited access to three position switch.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, c, d, e, f, g, i, j, k, or l.
 
h.
Key operated 3-position control switch rated 115V AC, 60 Hz to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, f, g, h, j, k, or l.
 
i.
3-position low voltage control switch with key locking cover plate rated 24V to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Select one of the following Video Interface Control and delete the remaining. Note that Video Interface Control is not compatible with low voltage control unit. Delete all of the following three paragraphs if video interface control is not required. Not compatible with options a. through j.
 
j.
Video Interface Control for use with equipment with a 115V switched outlet.
k.
Video Interface Control for use with equipment with a 12V switched outlet..
l.
Video Interface Control for use with equipment with a 6V switched outlet.
 
** NOTE TO SPECIFIER ** Left hand motor location is standard. Right hand location is optional (screen will be reverse rolled). Select required paragraph and delete paragraph not required.
 
m.
Motor shall be right mounted (screen will be reverse rolled).
n.
Motor shall be left mounted.
4.
System Options:
 
** NOTE TO SPECIFIER ** Select the required case finish and delete one of the following two paragraphs.
 
a.
Case finished black (standard).
b.
Case finished white.
 
** NOTE TO SPECIFIER ** Delete following paragraph if projected mounting bracket is not required.
 
c.
Projected Mounting Brackets with a 6 inch (152 mm) clearance from wall. Finished black.
d.
Floating Mounting Brackets for mounting screen to wall or ceiling.
 
** NOTE TO SPECIFIER ** Delete following paragraph if recessed ceiling installation is not required.
 
e.
Ceiling Trim Kit for recessing above acoustical tile ceiling grid.
5.
Projection Viewing Surface: Mildew resistant 100 percent vinyl with black masking borders and 12 inch (305 mm) black drop.
 
** NOTE TO SPECIFIER ** Select the screen type from the following paragraphs and delete those not required. Note that there are size limitations with some viewing surfaces. Contact manufacturer for additional information.
 
a.
Matt White XT1000V - On Axis gain of 1.0. 180 degree viewing cone. GREENGUARD Gold certified. Available with or without black backing.
b.
Pure White XT1300V - On Axis gain of 1.3. 180 degree viewing cone. For use in situations where lighting is well controlled and where enhanced brightness is needed due to limited projector brightness. Available with or without black backing.
 
** NOTE TO SPECIFIER ** Grey XH600V maximum size available is 9 feet by 12 feet (274 cm x 366 cm).
 
c.
Grey XH600V - On Axis gain of 0.6. Provides excellent contrast and color reproduction. GREENGUARD Gold certified. Available with or without black backing.
 
** NOTE TO SPECIFIER ** Pearl White CH1900E maximum size available is 9 feet by 12 feet (274 cm x 366 cm).
 
d.
Pearl White CH1900E - On Axis gain of 1.9. Matt white surface with reflective pearlescent coating and black backing.
 
** NOTE TO SPECIFIER ** ReAct MS1000V maximum size available is 79 inches by 140 inches (201 cm x 356 cm).
 
e.
ReAct MS1000V - On Axis gain of 1.0. 60 degree viewing cone. Silver/grey surface provides superior performance in ambient light conditions, offers excellent contrast, optimal color rendition, and is fully HD compliant.
 
** NOTE TO SPECIFIER ** ClearSound NanoPerf XT800V is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
f.
ClearSound NanoPerf XT800V - On Axis gain of 0.8. 180 degree viewing cone. Acoustically transparent white PVC fabric with microscopic perforations.
 
** NOTE TO SPECIFIER ** ClearSound NanoPerf XT900V is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 20 feet (610 cm) from screen.
 
g.
ClearSound Perf XT900V - On Axis gain of 1.0. 180 degree viewing cone. Acoustically transparent. Flexible matt white perforated surface. Reasonable control of ambient light is recommended.
h.
TecVision XH700X Grey - On Axis gain of 0.7. 180 degree viewing cone. Designed for blending applications on curved or flat screens where ambient light is present. Provides very good contrast and color reproduction. Imaging Science Foundation certified and 4K ready. Dark backing.
i.
TecVision XT1100X White - On-Axis gain of 1.1. 180 degree viewing cone. Designed for use when the projector brightness and size of screen require a minimal increase in gain. Imaging Science Foundation certified and 4K ready. Dark backing.
j.
TecVision XH900X Grey - On Axis gain of 0.9. 180 degree viewing cone. Provides very good contrast and color reproduction. Imaging Science Foundation certified. 4K ready. Dark backing.
k.
TecVision MS1000X Grey - On Axis gain of 1.0. 70 degree viewing cone. Provides excellent contrast and color reproduction. Performs well in ambient light. Imaging Science Foundation certified. 4K ready. Dark backing.
l.
TecVision XT1000X White - On Axis gain of 1.0. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready reference screen surface for blending applications, precise resolution, and color accuracy. Dark backing.
m.
TecVision XT1300X White - On Axis gain of 1.3. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready. Dark backing.
n.
TecVision XT1600X White - On Axis gain of 1.6. 180 degree viewing cone. Imaging Science Foundation certified. 4K ready. Dark backing.
o.
TecVision XT1800X White - On Axis gain of 1.8. 180 degree viewing cone. Imaging Science Foundation certified. Suited for active 3D or color combining passive 3D systems. 4K ready. Dark backing.
p.
CineFlex CH1200V - On Axis gain of 1.2. 60 degree viewing cone. Neutral grey rear projection diffusing surface. Provides high resolution and excellent contrast, even in lighted rooms. Recommended for use with low to medium output projectors.
q.
CineFlex XT600V - On Axis gain of 0.6. 180 degree viewing cone. White rear projection surface works well for edge matching or edge blending applications, and also for short throw rear projection. Reasonable control of ambient light is recommended.
r.
CineFlex MH800V - On Axis gain of 0.8. 78 degree viewing cone. Low gain flexible rear material. Designed for use with high light output projectors and wide audience seating patterns.
6.
Tab-Tensioning System:
a.
Viewing surface with integrated tabs and cable on each side of fabric to provide tension and ensure flat viewing surface. Viewing surface and tabs CNC cut as a single piece. Tabs RF welded to the back of viewing surface to prevent tab separation. Tab adhesives are not acceptable. Viewing surface inserted into aluminum bottom dowel. Warranted for 5 years against tab separation.
 
** NOTE TO SPECIFIER ** Select the screen format and size required for the project. Delete the paragraphs not required. Ceiling Opening Trim Kit is not available for Premier over 12 foot x 12 foot AV, 200 inches NTSC, 184 inches HDTV, and 189 inches 16:10, depending on the format.
 
7.
Viewing Area H x W. Black masking borders standard. 12 inch (305 mm) black drop standard.
a.
Custom Size: ________ H x ____________ W.
b.
NTSC Format (4:3).
1)
6 foot (1.83 m) diagonal, 42-1/2 inches x 56-1/2 inches (1080 mm x 1435 mm).
2)
7 foot (2.13 m) diagonal, 50 inches x 66-1/2 inches (1270 mm x 1689 mm).
3)
100 inch (2540 mm) diagonal, 60 inches x 80 inches (1524 mm x 2032 mm).
4)
10 foot (3.05 m) diagonal, 72 inches x 96 inches (1829 mm x 2438 mm).
5)
11 foot (3.35 m) diagonal, 78 inches x 104 inches (1981 mm x 2642 mm).
6)
150 inch (3810 mm) diagonal, 87 inches x 116 inches (2210 mm x 3658 mm).
7)
15 foot (4.572 m) diagonal, 108 inches x 144 inches (2743 mm x 3658 mm).
8)
200 inch (508 mm) diagonal, 118 inches x 158 inches (2997 mm x 4013 mm).
 
** NOTE TO SPECIFIER ** The following large NTSC sizes require a different case construction with a larger profile. These are not compatible with 6" extension brackets, Ceiling Opening Trim Kit, Floating Wall Brackets, or optional Q, L, and QL motors. Contact Draper for additional information.
 
9)
210 inch (5.33 m) diagonal, 126 inches x 168 inches (3200 mm x 4267 mm).
10)
220 inch (5.59 m) diagonal, 132 inches x 176 inches (3353 mm x 4470 mm).
11)
230 inch (5.84 m) diagonal, 138 inches x 184 inches (3505 mm x 4674 mm).
12)
20 foot (6.10 m) diagonal, 144 inches x 192 inches (3658 mm x 4877 mm).
c.
HDTV Format (16:9).
1)
65 inch (1651 mm) diagonal, 31-3/4 inches x 56-1/2 inches (806 mm x 1435 mm).
2)
73 inch (1854 mm) diagonal, 36 inches x 64 inches (914 mm x 1626 mm).
3)
82 inch (2083 mm) diagonal, 40-1/2 inches x 42 inches (1029 mm x 1067 mm).
4)
92 inch (2337 mm) diagonal, 45 inches x 80 inches (1143 mm x 2032 mm).
5)
100 inch (2540 mm) diagonal, 49 inches x 87 inches (1245 mm x 2210 mm)
6)
106 inch (2692 mm) diagonal, 52 inches x 92 inches (1321 mm x 2337 mm).
7)
110 inch (2794 mm) diagonal, 54 inches x 96 inches (1372 mm x 2438 mm)
8)
119 inch (3023 mm) diagonal, 58 inches x 104 inches (1473 mm x 2642 mm).
9)
133 inch (3378 mm) diagonal, 65 inches x 116 inches (1651 mm x 2947 mm).
10)
161 inch (4089 mm) diagonal, 79 inches x 140 inches (2007 mm x 3556 mm).
11)
184 inch (4673 mm) diagonal, 90 inches x 160 inches (2286 mm x 4064 mm).
 
** NOTE TO SPECIFIER ** The following large HDTV sizes require a different case construction with a larger profile. These are not compatible with 6" extension brackets, Ceiling Opening Trim Kit, Floating Wall Brackets, or optional Q, L, and QL motors. Contact Draper for additional information.
 
12)
193 inch (4.90 m) diagonal, 94-1/2 inches x 168 inches (2400 mm x 4267 mm).
13)
220 inch (5.59 m) diagonal, 108 inches x 192 inches (2743 mm x 4877 mm).
d.
16:10 Format. Black masking borders standard.
1)
67 inch (1702 mm) diagonal, 35-1/4 inches x 56-1/2 inches (895 mm x 1435 mm).
2)
76 inch (1930 mm) diagonal, 40 inches x 64 inches
3)
85 inch (2159 mm) diagonal, 45 inches x 72 inches (1143 mm x 1829 mm).
4)
94 inch (2438 mm) diagonal, 50 inches x 80 inches (1270 mm x 2032 mm).
5)
109 inch (2769 mm) diagonal, 57-1/2 inches x 92 inches (1461 mm x 2337 mm).
6)
113 inch (2870 mm) diagonal, 60 inches x 96 inches (1524 mm x 2438 mm).
7)
123 inch (3124 mm) diagonal, 65 inches x 104 inches (1351mm x 2642 mm).
8)
137 inch (3480) diagonal, 72-1/2 inches x 116 inches (1842 mm by 2946 mm).
9)
165 inch (4191 mm) diagonal, 87-1/2 inches x 140 inches (2223 mm by 3556 mm).
10)
189 inch (4800 mm) diagonal, 100 inches x 160 inches (2540 mm x 4064 mm).
 
** NOTE TO SPECIFIER ** The following large 16:10 sizes require a different case construction with a larger profile. These are not compatible with 6" extension brackets, Ceiling Opening Trim Kit, Floating Wall Brackets, or optional Q, L, and QL motors. Contact Draper for additional information.
 
11)
198 inch (5029 mm) diagonal, 105 inches x 168 inches (2667 mm x 4267 mm).
12)
226 inch (5740 mm) diagonal, 120 inches x 192 inches (3048 mm x 4877 mm).
 
** NOTE TO SPECIFIER ** If an extra screen drop exceeding the standard of 12 inches (305 mm) is required for the project fill in the drop height and select one of the following paragraphs and delete the other. Total screen height cannot exceed 14 feet (4.27 m). Select viewing surface color or black. Black is standard. If extra screen drop is not required, delete both paragraphs.
 
8.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with top border matching the viewing surface.
9.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with a black masking top border.
F.
Targa: Electric motor operated, steel case. Cases for sizes through 12 feet x 12 feet AV, 200 inch NTSC, 184 inch HDTV and 189 inch 16:10, are one piece 22 gauge steel with end caps forming universal wall or ceiling hanging bracket. Cases for sizes above 12 feet x 12 feet AV, 200 inch NTSC, 184 inch HDTV and 189 inch 16:10 consists of a curved front and L-shaped back/top cover fabricated of extruded aluminum, with endcaps forming ceiling hanging bracket. White scratch resistant textured finish.
 
** NOTE TO SPECIFIER ** Select one of the following motor paragraphs and associated control option as required. Delete the paragraphs not required. Note that there are size limitations with quiet motors. Contact manufacturer for additional information.
 
1.
Motor mounted inside screen roller on rubber isolation insulators. Motor UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches.
2.
Quiet Motor mounted inside screen roller on rubber isolation insulators. Motor operates at 44db. UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches.
 
** NOTE TO SPECIFIER ** Select controls and wall and/or remote-control switches required for project. Delete from the following paragraphs the types of controls and switches not used on the project. Coordinate the compatibility of multiple control selections.
 
3.
Motor Screen Controls, UL certified.
 
** NOTE TO SPECIFIER ** Not compatible with options b, c, d, e, h, i, j, k, or l.
 
a.
Single station control rated 115V AC, 60 Hz with 3-position rocker switch with cover plate to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, c, d, e, h, i, j, k, or l.
 
b.
Multiple station control rated 115V AC, 60 Hz with 3-position rocker switches with cover plates to stop or reverse screen at any point. Automatic override allows only one signal to reach the motor when operated simultaneously
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
c.
Low voltage control unit with three button 24V switches and cover plate to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
d.
Low voltage 24V control unit with hand held RF remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, g, h, j, k, or l.
 
e.
Low voltage 24V control unit with hand held IR remote three button control switch to stop or reverse screen at any point, built-in RF receiver, built-in Video Interface Control trigger for 3V-28V, RS232, and dry contact relays.
 
** NOTE TO SPECIFIER ** Not compatible with options g, h, i, j, k, or l.
 
f.
Key Operated power supply switch to control power to control system.
 
** NOTE TO SPECIFIER ** Not compatible with options d, e, f, h, i, j, k, or l.
 
g.
Locking switch cover plate for limited access to three position switch.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, c, d, e, f, g, i, j, k, or l.
 
h.
Key operated 3-position control switch with key locking cover plate rated 115V AC, 60 Hz to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Not compatible with options a, b, f, g, h, j, k, or l.
 
i.
3-position low voltage control switch rated 24V to stop or reverse screen at any point.
 
** NOTE TO SPECIFIER ** Select one of the following Video Interface Control and delete the remaining. Note that Video Interface Control is not compatible with low voltage control unit. Delete all of the following three paragraphs if video interface control is not required. Not compatible with options a. through j.
 
j.
Video Interface Control for use with equipment with a 115V switched outlet.
k.
Video Interface Control for use with equipment with a 12V switched outlet..
l.
Video Interface Control for use with equipment with a 6V switched outlet.
 
** NOTE TO SPECIFIER ** Left hand motor location is standard. Right hand location is optional (screen will be reverse rolled). Select required paragraph and delete paragraph not required.
 
m.
Motor shall be right mounted (screen will be reverse rolled).
n.
Motor shall be left mounted.
4.
System Options:
 
** NOTE TO SPECIFIER ** Select the required case finish and delete two of the following paragraphs.
 
a.
Case finished black (standard).
b.
Case finished white.
 
** NOTE TO SPECIFIER ** Delete following paragraph if projected mounting bracket is not required.
 
c.
Projected Mounting Brackets with a 6 inch (152 mm) clearance from wall. Finished white or black.
d.
Floating Mounting Brackets for mounting screen to wall or ceiling.
 
** NOTE TO SPECIFIER ** Delete following paragraph if recessed ceiling installation is not required.
 
e.
Ceiling Trim Kit for recessing above acoustical tile ceiling grid.
5.
Projection Viewing Surface:
 
** NOTE TO SPECIFIER ** Select the screen type from the following paragraphs and delete those not required. Note that there are size limitations with some viewing surfaces. Contact manufacturer for additional information.
 
a.
Matt White XT1000E - On Axis gain of 1.0. 180 degree viewing cone. Washable surface. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Argent White XH1500E maximum size available is 8 feet by 10 feet (244 cm x 305 cm).
 
b.
Argent White XH1500E - On Axis gain of 1.5. High reflectivity fabric with broad viewing cone. Excellent resolution and color balance. Flame and Mildew resistant.
 
** NOTE TO SPECIFIER ** Pearl White CH1900E maximum size available is 96 inches by 96 inches (244 cm x 244 cm).
 
c.
Pearl White CH1900E - On Axis gain of 1.9. Matt white surface with reflective pearlescent coating.
d.
Contrast Grey XH800E - 0.8 On Axis gain. Smooth grey surface provides excellent resolution and enhances color contrast. 180 degree viewing cone. GREENGUARD Gold certified.
 
** NOTE TO SPECIFIER ** Contrast White XH1100E maximum size available is 8 feet by 10 feet (244 cm x 305 cm).
 
e.
Contrast White XH1100E - On Axis gain of 1.1. Diffuse white coating over a grey base material. Recommended for use with low to moderate light output digital projectors, where some provision for light control exists.
 
** NOTE TO SPECIFIER ** ClearSound Perf XT950E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 20 feet (601 cm) from screen.
 
f.
ClearSound Perf XT950E - On Axis gain of 0.95. 180 degree viewing cone. Acoustically transparent. Textile backed matt white perforated surface.
 
** NOTE TO SPECIFIER ** ClearSound White Weave XT900E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
g.
ClearSound White Weave XT900E - On Axis gain of 0.9. 180 degree viewing cone. Acoustically transparent woven blend of fiberglass and PVC. Acoustical properties are comparable to the highest quality speaker grille cloth. Some control of ambient light is recommended. Flame and mildew resistant.
 
** NOTE TO SPECIFIER ** ClearSound Grey Weave XH600E is not recommended for use in sizes less than 80 inches (203 cm) wide or for viewing less than 10 feet (305 cm) from screen.
 
h.
ClearSound Grey Weave XH600E - On Axis gain of 0.6. 180 degree viewing cone. Acoustically transparent woven blend of fiberglass and PVC. Grey material for higher contrast. Acoustical properties are comparable to the highest quality speaker grille cloth. Flame and mildew resistant.
i.
Chroma Key Blue - Blue flexible PVC surface for video production where you need the background to "disappear." Matte finish. Flame retardant, tear resistant, and wrinkle resistant. Offers excellent uniformity and consistent surface color edge to edge. Works effectively throughout 180 degree viewable range.
j.
Chroma Key Green - Green flexible PVC surface for video production where you need the background to "disappear." Matte finish. Flame retardant, tear resistant, and wrinkle resistant. Offers excellent uniformity and consistent surface color edge to edge. Works effectively throughout 180 degree viewable range.
 
** NOTE TO SPECIFIER ** Select the screen format and size required for the project. Delete the paragraphs not required. Ceiling Opening Trim Kit is not available for Targa over 12 foot x 12 foot AV, 200 inches NTSC, 184 inches HDTV, and 189 inches 16:10.
 
6.
Viewing Area H x W.
a.
Custom Size: ________ H x ____________ W.
b.
NTSC Format (4:3). Black masking borders standard.
1)
6 foot (1.83 m) diagonal, 42-1/2 inches x 56-1/2 inches (1080 mm x 1435 mm).
2)
7 foot (2.13 m) diagonal, 50 inches x 66-1/2 inches (1270 mm x 1689 mm).
3)
100 inch (2540 mm) diagonal, 60 inches x 80 inches (1524 mm x 2032 mm).
4)
10 foot (3.05 m) diagonal, 69 inches x 92 inches (1753 mm x 2337 mm).
5)
11 foot (3.35 m) diagonal, 78 inches x 104 inches (1981 mm x 2642 mm).
6)
150 inch (3810 mm) diagonal, 87 inches x 116 inches (2210 mm x 3658 mm).
7)
15 foot (4.57 m) diagonal, 105 inches x 140 inches (2667 mm x 3556 mm).
8)
200 inch (5080 mm) diagonal, 118 inches x 158 inches (2997 mm x 4013 mm).
 
** NOTE TO SPECIFIER ** The following large NTSC sizes require a different case construction with a larger profile. These are not compatible with 6 inch extension brackets, Ceiling Opening Trim Kit, Floating Wall Brackets, or optional Q, L, and QL motors. Contact Draper for additional information.
 
9)
210 inch (5.33 m) diagonal, 126 inches x 168 inches (3200 mm x 4268 mm).
10)
240 inch (6.10 m) diagonal, 141 inches x 188 inches (3581 mm x 4776 mm).
c.
HDTV Format (16:9). Black masking borders standard.
1)
65 inch (1651 mm) diagonal, 31-3/4 inch by 56-1/2 inch (781 mm by 1435 mm).
2)
73 inch (1854 mm) diagonal, 36 inches x 64 inches (
3)
82 inch (2083 mm) diagonal, 40-1/2 inches x 72 inches (
4)
92 inch (2337 mm) diagonal, 45 inches x 80 inches (1143 mm x 2032 mm).
5)
100 inch (2540 mm) diagonal, 49 inches x 87 inches (1245 mm x 2210 mm).
6)
106 inch (2692 mm) diagonal, 52 inches x 92 inches (1321 mm x 2337 mm).
7)
110 inch (2794 mm) diagonal, 54 inches x 96 inches (1372 mm x 2438 mm).
8)
119 inch (3023 mm) diagonal, 58 inches x 104 inches (1473 mm x 2642 mm).
9)
133 inch (3378 mm) diagonal, 65 inches x 116 inches (1651 mm x 2947 mm).
10)
161 inch (4089 mm) diagonal, 79 inches x 140 inches (2007 mm x 3556 mm).
11)
184 inch (4674 mm) diagonal, 90 inches x 160 inches (2286 mm x 4064 mm).
 
** NOTE TO SPECIFIER ** The following large HDTV sizes require a different case construction with a larger profile. These are not compatible with 6 inch extension brackets, Ceiling Opening Trim Kit, Floating Wall Brackets, or optional Q, L, and QL motors. Contact Draper for additional information.
 
12)
193 inch (4.90 m) diagonal, 94-1/2 inches x 168 inches (2400 mm x 4268 mm).
13)
220 inch (5.59 m) diagonal, 106 inches x 188 inches (2692 mm x 4776 mm).
d.
16:10 Format. Black masking borders standard.
1)
67 inch (1702 mm) diagonal, 35-1/4 inches x 56-1/2 inches (895 mm x 1435 mm).
2)
76 inch (1930 mm) diagonal, 40 inches x 64 inches
3)
85 inch (2159 mm) diagonal, 45 inches x 72 inches (1143 mm x 1829 mm).
4)
94 inch (2438 mm) diagonal, 50 inches x 80 inches (1270 mm x 2032 mm).
5)
109 inch (2769 mm) diagonal, 57-1/2 inches x 92 inches (1461 mm x 2337 mm).
6)
113 inch (2870 mm) diagonal, 60 inches x 96 inches (1524 mm x 2438 mm).
7)
123 inch (3124 mm) diagonal, 65 inches x 104 inches (1351mm x 2642 mm).
8)
137 inch (3480) diagonal, 72-1/2 inches x 116 inches (1842 mm by 2946 mm).
9)
165 inch (4191 mm) diagonal, 87-1/2 inches x 140 inches (2223 mm by 3556 mm).
10)
189 inch (4800 mm) diagonal, 100 inches x 160 inches (2540 mm x 4064 mm).
 
** NOTE TO SPECIFIER ** The following large HDTV sizes require a different case construction with a larger profile. These are not compatible with 6 inch extension brackets, Ceiling Opening Trim Kit, Floating Wall Brackets, or optional Q, L, and QL motors. Contact Draper for additional information.
 
11)
198 inch (5029 mm) diagonal, 105 inches x 168 inches (2667 mm x 4267 mm).
12)
222 inch (5639 mm) diagonal, 117 inches x 188 inches (2972 mm x 4775 mm).
 
** NOTE TO SPECIFIER ** If an extra screen drop is required for the project, fill in the drop height and select one of the following paragraphs. Total screen height cannot exceed 18 feet (5.49 m). Select viewing surface color or black. Matching the viewing surface is standard for AV format, black is standard for all other formats. If not required, delete both paragraphs.
 
7.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with top border matching the viewing surface.
8.
Provide an extra screen drop with an overall screen drop of ___ inches (___ mm) with a black masking top border.
 
** NOTE TO SPECIFIER ** Delete the following front projection screen if not used on the project.
 
2.4
FIXED, SURFACE MOUNTED, FRONT PROJECTION SCREENS
A.
Scribe - Write-On Fixed Projection Screen: Magnetic whiteboard surface with low profile black bezel frame. Flush wall mounting with sliding brackets, integrated in the back of the frame. Includes tray, eraser, markers and liquid cleaner.
 
** NOTE TO SPECIFIER ** The Image format from the following paragraphs and delete the one not required.
 
1.
Size Options: Image format 16:10
 
** NOTE TO SPECIFIER ** Select the size required and delete one of the following paragraphs.
 
a.
Image Diagonal: 87 inches (2210 mm).
1)
Viewable Area: 46-1/8 inches x 73-3/4 inches 1172 mm x 1873 mm).
2)
Overall Size: 46-5/8 inches x 74-1/4 inches (1184 mm x 1886 mm.
b.
Image Diagonal: 68 inches (1727 mm).
1)
Viewable Area: 36 inches x 57-1/2 inches (914 mm x 1461 mm).
2)
Overall Size: 36-1/2 inches x 58 inches (927 mm x 1473 mm).
2.
Size Options: Image format HDTV 16:9
 
** NOTE TO SPECIFIER ** Select the size required and delete one of the following paragraphs.
 
a.
Image Diagonal: 94 inches (2388 mm).
1)
Viewable Area: 46-1/8 inches x 82-1/8 inches (1172 mm x 2086 mm).
2)
Overall Size: 46-5/8 inches x 82-5/8 inches (1184 x 2091 mm.
b.
Image Diagonal: 73 inches (1854 mm).
1)
Viewable Area: 36 inches x 64 inches (914 mm x 1626 mm).
2)
Overall Size: 36-1/2 inches x 64-1/2 inches (927 mm x 1638 mm).
PART 3 EXECUTION
 
3.1
EXAMINATION
A.
Do not begin installation until substrates have been properly prepared.
B.
Verify rough-in openings are properly prepared.
C.
If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
3.2
PREPARATION
A.
Clean surfaces thoroughly prior to installation.
B.
Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
3.3
INSTALLATION
A.
Install in accordance with manufacturer's instructions.
B.
Install front projection screens with screen cases in position and relationship to adjoining construction as indicated, securely anchored to supporting substrate, and in manner that produces a smoothly operating screen with plumb and straight vertical edges and plumb and flat viewing surfaces when screen is lowered.
 
** NOTE TO SPECIFIER ** Select manual or electrically operated screens from the following two paragraphs as required by the project requirements.
 
C.
Test manually operated units to verify that screen operating components are in optimum functioning condition
D.
Test electrically operated units to verify that screen, controls, limit switches, closure and other operating components are in optimum functioning condition.
3.4
PROTECTION
A.
Protect installed products until completion of project.
B.
Touch-up, repair or replace damaged products before Substantial Completion.
END OF SECTION