Download SECTION 12 93 43.13 SITE BENCHES for
WORD | RTF | Text | Word Perfect
Find over 500 more CSI Sections
on Arcat.com
Switch to Masterformat 95
 
SECTION 12 93 43.13
SITE BENCHES
 
 
Copyright 2006 - 2015 ARCAT, Inc. - All rights reserved
** NOTE TO SPECIFIER ** DuMor, Inc.; Site Furnishing products.
.
This section is based on the products of DuMor, Inc., which is located at:
 
P.
O. Box 142
 
Mifflintown, PA 17059-0142
Toll Free Tel: 800-598-4018
Tel: 717-436-2106
Fax: 717-436-9839
Email: request info (sales@dumor.com)
Web: www.dumor.com
[ Click Here ] for additional information.
DuMor Site Furnishings, Inc., one of America's most prominent producers of site furnishings, is adding several new site furnishings to our already extensive line for 2006. For over 20 years, DuMor Site Furnishings has been designing stylish and functional site furnishings for parks and common areas across the country. Site furnishings by DuMor Site Furnishings are available with a variety of polyester powder finishes, heavy-duty support options, recycled plastic colors, as well as high-grade woods.
 
PART 1 GENERAL
 
1.1
SECTION INCLUDES
 
** NOTE TO SPECIFIER ** Delete items below not required for project.
 
A.
Steel Benches.
B.
Recycled Plastic Benches.
C.
Wood Benches.
1.2
RELATED SECTIONS
 
** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
 
A.
Section 12 93 13 - Bicycle Racks.
1.3
REFERENCES
 
** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
 
A.
ASTM A 36 - Standard Specification for Carbon Structural Steel.
B.
ASTM A 123 - Standard Specification for Zinc (hot-dip galvanized) Coatings on Iron and Steel Products.
C.
ASTM A 53 - Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless.
1.4
SUBMITTALS
A.
Submit under provisions of Section 01 30 00 - Administrative Requirements.
B.
Product Data: Manufacturer's data sheets on each product to be used, including:
1.
Preparation instructions and recommendations.
2.
Storage and handling requirements and recommendations.
3.
Installation methods.
C.
Shop Drawings: Complete details of layout and assembly, showing member sizes and part identification, fasteners, anchors, and fittings.
 
** NOTE TO SPECIFIER ** Delete the following paragraphs if LEED is not applicable.
 
D.
LEED Submittals: Provide documentation of how the requirements of Credit will be met:
1.
Product Data for Credit MR 2.1 and 2.2: For products being recycled, documentation of total weight of project waste diverted from landfill.
2.
Product Data for Credit MR 4.1 and MR 4.2: For products having recycled content, documentation including percentages by weight of post consumer and preconsumer recycled content
a.
Include statement indicating costs for each product having recycled content.
3.
Product Data for Credit MR 5.1 and Credit MR 5.2: Submit data, including location and distance from Project of material manufacturer and point of extraction, harvest or recovery for main raw material.
a.
Include statement indicating cost for each regional material and the fraction by weight that is considered regional.
 
** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.
 
E.
Selection Samples: Color selections shall be made from the manufacturer's brochure representing manufacturer's full range of available colors and patterns.
F.
Manufacturer's Certificates: Certify products meet or exceed specified requirements.
G.
Manufacturers warranties.
1.5
QUALITY ASSURANCE
A.
Manufacturer Qualifications: Minimum of 15 years experience manufacturing site benches.
B.
Installer Qualifications: Minimum of 5 years experience assembling and installing site benches.
 
** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.
 
C.
Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.
1.
Finish areas designated by Architect.
2.
Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.
3.
Refinish mock-up area as required to produce acceptable work.
1.6
DELIVERY, STORAGE, AND HANDLING
A.
Store products in manufacturer's unopened packaging until ready for installation.
B.
Protect materials from exposure to moisture. Do not deliver until conditions are ready for installation.
1.7
WARRANTY
A.
Limited twenty-year warranty against structural failure of all steel bench frames or complete steel bench assemblies including cast iron bench supports.
B.
Limited five-year warranty against structural failure of douglas fir, redwood, and ipe wood bench materials.
C.
Limited ten-year warranty against structural failure of recycled plastic; it is further warrantied not to degrade, split, crack, or splinter during this period.
1.8
COORDINATION
A.
Coordinate Work with other operations and installation of benches to avoid damage to installed materials.
PART 2 PRODUCTS
 
2.1
MANUFACTURERS
A.
Acceptable Manufacturer: DuMor, Inc., which is located at: P. O. Box 142; Mifflintown, PA 17059-0142; Toll Free Tel: 800-598-4018; Tel: 717-436-2106; Fax: 717-436-9839; Email: request info (sales@dumor.com); Web: www.dumor.com
 
** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
 
B.
Substitutions: Not permitted.
C.
Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.
 
** NOTE TO SPECIFIER ** Select site furnishings required from the following paragraphs; delete paragraphs that are not required. Visit the manufacturer's web site at www.dumor.com for photos of standard designs. Contact the manufacturer for non-standard and custom products.
** NOTE TO SPECIFIER ** Select one or more of the following bench models. If more than one model is selected, clearly indicate the location of each on the Drawings. Delete models not used.
 
2.2
BENCHES
A.
Steel Benches with Backrests.
1.
DuMor 58 Series. Welded seat and back.
a.
End frames: Cast iron bench supports.
b.
Seats: 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bars.
c.
Fasteners: Stainless steel.
d.
Bracing: 1-1/4 inch (32 mm) O.D. pipe.
e.
Height: 17-1/16 inches (434 mm).
f.
Width: 27-9/16 inches (700 mm).
 
** NOTE TO SPECIFIER ** Center armrest is optional, delete if not required.
 
g.
Center Armrest: Cast Iron.
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
h.
Length: 6 feet (1829 mm).
i.
Length: 8 feet (2438 mm).
j.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Side panels are optional, delete if not required.
 
k.
Side Panels: Provide with custom lettered side panels as selected by the Architect.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
l.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
2.
DuMor 19 Series. Welded seat and back.
a.
End frames: Cast iron bench supports.
 
** NOTE TO SPECIFIER ** Armrest optional, delete if not required.
 
b.
Armrest: Cast Iron.
c.
Seats: 5/8 inch (15.9 mm) diameter steel bars and 2-3/8 inch (60 mm) O.D. steel pipe.
d.
Fasteners: Stainless steel.
e.
Bracing: 1-1/4 inch (32 mm) O.D. pipe.
f.
Height: 17 inches (432 mm).
g.
Width: 27-9/16 inches (700 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
h.
Length: 6 feet (1829 mm).
i.
Length: 8 feet (2438 mm).
j.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Side panels are optional, delete if not required.
 
k.
Side Panels: Provide with custom lettered side panels as selected by the Architect.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
l.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
3.
DuMor 59 Series.
a.
End frames and Supports: 1/2 inch (12.5 mm) by 3 inch (76 mm) steel bar.
 
** NOTE TO SPECIFIER ** Select one of the following support options and delete those not required.
 
1)
Embedment.
2)
Surface plate.
3)
Gull wing.
4)
Sub-floor.
b.
Seats: 10 gauge perforated steel.
c.
Fasteners: Stainless steel.
d.
Height: 17-1/2 inches (444 mm).
e.
Width: 27-7/16 inches (697 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required and delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Provide with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
2)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
4.
DuMor 93 Series. One piece seat surface construction.
a.
End frames: Cast iron bench supports.
b.
Seats: 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bars and 2-3/8 inch (60 mm) O.D. pipe.
c.
Fasteners: Stainless steel.
d.
Height: 16-1/16 inches (408 mm).
e.
Width: 28-1/8 inches (714 mm).
 
** NOTE TO SPECIFIER ** Center armrest is optional, delete if not required.
 
f.
Center Armrest: 1 inch (25 mm) by 1-1/2 inch (38 mm) steel bar bench supports.
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
5.
DuMor 94 Series.
a.
End frames: 2 inch (50 mm) square steel by 11 gauge thick bench supports.
b.
Seats: 1 inch (25 mm) square by 13 gauge thick steel tubing and 2 inch (50 mm) by 1 inch (25 mm) by 13 gauge thick steel tube.
c.
Backs: 1/2 inch (12.5 mm) thick steel and 2 inch (50 mm) by 1 inch (25 mm) by 13 gauge thick steel tube.
d.
Fasteners: Stainless steel.
e.
Height: 16-3/4 inches (425 mm).
f.
Width: 26-7/16 inches (672 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
i.
Mounting:
1)
Free standing with adjustable nylon pad feet.
2)
Provide with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
3)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
6.
DuMor 117 Series. Chippendale design.
a.
End frames: 2 inch (50 mm) square steel by 11 gauge thick bench supports.
b.
Seats: 2 inch (50 mm) by 1 inch (25 mm) by 13 gauge thick steel tubing.
c.
Backs: 2 inch (50 mm) by 1 inch (25 mm) by 13 gauge thick steel tubing, 3/8 inch (10 mm) by 1-1/2 inch (38 mm) steel bar and 3/8 inch (10 mm) thick steel.
d.
Fasteners: Stainless steel.
e.
Height: 16-3/4 inches (425 mm).
f.
Width: 26-7/16 inches (672 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
i.
Mounting:
1)
Free standing with adjustable nylon pad feet.
2)
Provide with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
3)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
7.
DuMor 118 Series. Arch back design.
a.
End frames: 2 inch (50 mm) square steel by 11 gauge thick bench supports.
b.
Seats: 1 inch (25 mm) square by 13 gauge steel tube and 2 inch (50 mm) by 1 inch (25 mm) by 13 gauge thick steel tubing.
c.
Backs: 2 inch (50 mm) by 1 inch (25 mm) by 13 gauge thick steel tubing, 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar.
d.
Fasteners: Stainless steel.
e.
Height: 16-3/4 inches (425 mm).
f.
Width: 26-7/16 inches (672 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
i.
Mounting:
1)
Free standing with adjustable nylon pad feet.
2)
Provide with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
3)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
8.
DuMor 119 Series. All welded seat assembly.
a.
End frames: Cast Iron.
b.
Seats: 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar and 2-3/8 inch (60 mm) O.D. steel pipe.
c.
Bracing: 1-1/16 inch (27 mm) O.D. steel pipe.
d.
Fasteners: Stainless steel.
e.
Height: 18-13/16 inches (478 mm).
f.
Width: 28-1/16 inches (712 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provide with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
9.
DuMor 127 Series. Heavy duty arm rests and supports.
a.
Supports: 2-1/2 inch (62 mm), schedule 40 steel pipe or 3/8 inch (10 mm) steel plate.
b.
Seats: 14 gauge perforated steel with 1/2 inch (12.5 mm) by 2 inch (50 mm) steel supports.
c.
Arm Rests: 3/8 inch (10 mm) by 2 inch (50 mm) steel.
d.
Fasteners: Stainless steel.
e.
Height: 17-7/16 inches (443 mm).
f.
Width: 25-7/16 inches (646 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 2 seats, 46-1/2 inches (1181 mm).
h.
Length: 3 seats, 68-3/4 inches (1746 mm).
i.
Length: 4 seats, 91 inches (2311 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
j.
Mounting:
1)
Tri-Support.
2)
Surface Plate.
3)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
k.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
10.
DuMor 136 Series.
a.
Supports: 3 inch (76 mm), schedule 40 steel pipe.
b.
Frame: 2 inch (50 mm), schedule 40 steel pipe.
c.
Seats: 10 gauge perforated steel.
d.
Fasteners: Stainless steel.
e.
Height: 17 inches (432 mm).
f.
Width: 25-1/2 inches (648 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
i.
Mounting:
1)
Sub-Floor.
2)
Surface Plate.
3)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
11.
DuMor 137 Series.
a.
Supports: 3 inch (76 mm), schedule 40 steel pipe.
b.
Frame: 2 inch (50 mm), schedule 40 steel pipe.
c.
Seats: 5/8 inch (15.9 mm) diameter steel rods and 3/8 inch (10 mm) by 4-1/2 inch (114 mm) steel bar and 1/2 inch (12.5 mm) by 3 inch (76 mm) bar.
d.
Fasteners: Stainless steel.
e.
Height: 18 inches (457 mm).
f.
Width: 28-1/4 inches (718 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
i.
Mounting:
1)
Sub-Floor.
2)
Surface Plate.
3)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
12.
DuMor 140 Series. All welded seat assembly.
a.
End frames: Cast Iron.
 
** NOTE TO SPECIFIER ** Armrest optional, delete if not required.
 
b.
Armrest: Cast Iron.
c.
Seats: 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar and 2-3/8 inch (60 mm) O.D. steel pipe.
d.
Bracing: 1-1/16 inch (27 mm) O.D. steel pipe.
e.
Fasteners: Stainless steel.
f.
Height: 17-1/16 inches (433 mm).
g.
Width: 27-9/16 inches (700 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
h.
Length: 6 feet (1829 mm).
i.
Length: 8 feet (2438 mm).
j.
Mounting: Provide with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Side panels are optional, delete if not required.
 
k.
Side Panels: Provide with custom lettered side panels as selected by the Architect.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
l.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
13.
DuMor 141 Series. Welded seat and back.
a.
End frames: Cast iron bench supports.
 
** NOTE TO SPECIFIER ** Armrest optional, delete if not required.
 
b.
Armrest: Cast Iron.
c.
Seats: 5/8 inch diameter steel bars, 1/4 inch (6 mm) by 2 inch (50 mm) steel and 3/8 inch (9.5 mm) steel plate.
d.
Fasteners: Stainless steel.
e.
Bracing: 1-1/16 inch (27 mm) O.D. steel pipe.
f.
Height: 17-1/16 inches (434 mm).
g.
Width: 27-9/16 inches (700 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
h.
Length: 6 feet (1829 mm).
i.
Length: 8 feet (2438 mm).
j.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Side panels are optional, delete if not required.
 
k.
Side Panels: Provide with custom lettered side panels as selected by the Architect.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
l.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
14.
DuMor 160 Series. Welded seat and back.
a.
End frames: Cast iron bench supports.
 
** NOTE TO SPECIFIER ** Armrest optional, delete if not required.
 
b.
Armrest: Cast Iron.
c.
Seats: 1-15/16 inch (49 mm) O.D. schedule 40 steel pipe, 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar.
d.
Fasteners: Stainless steel.
e.
Height: 16-11/16 inches (424 mm).
f.
Width: 27-5/16 inches (694 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
15.
DuMor 161 Series. Welded seat and back.
a.
End frames: Cast iron bench supports.
 
** NOTE TO SPECIFIER ** Armrest optional, delete if not required.
 
b.
Armrest: Cast Iron.
c.
Seats: 1 inch (25 mm) square by 13 gauge wall and 2 inch (50 mm) by 1 inch (25 mm) by 13 gauge steel wall tubing.
d.
Back Panel: 1/4 inch (6 mm) steel plate and 2 inch (50 mm) by 1 inch (25 mm) by 13 gauge steel wall tubing.
e.
Bracing: 1-1/16 inch (27 mm) O.D. steel pipe.
f.
Fasteners: Stainless steel.
g.
Height: 16-3/4 inches (425 mm).
h.
Width: 27-9/16 inches (700 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
i.
Length: 6 feet (1829 mm).
j.
Length: 8 feet (2438 mm).
k.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
l.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
16.
DuMor 162 Series. Welded seat and back.
a.
End frames: Cast iron bench supports.
 
** NOTE TO SPECIFIER ** Armrest optional, delete if not required.
 
b.
Armrest: Cast Iron.
c.
Seats: 1 inch (25 mm) square by 13 gauge wall and 2 inch (50 mm) by 1 inch (25 mm) by 13 gauge steel wall tubing.
d.
Back Panel: 1/4 inch (6 mm) steel plate and 2 inch (50 mm) by 1 inch (25 mm) by 13 gauge steel wall tubing.
e.
Bracing: 1-1/16 inch (27 mm) O.D. steel pipe.
f.
Fasteners: Stainless steel.
g.
Height: 16-3/4 inches (425 mm).
h.
Width: 27-9/16 inches (700 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
i.
Length: 6 feet (1829 mm).
j.
Length: 8 feet (2438 mm).
k.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
l.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
17.
DuMor 168 series. Welded seat and back.
a.
End frames: Cast iron bench supports.
 
** NOTE TO SPECIFIER ** Armrest optional, delete if not required.
 
b.
Armrest: Cast Iron.
c.
Seats: 1-15/16 inch (49 mm) O.D. schedule 40 steel pipe, 3/8 " (?? mm) diameter steel bar.
d.
Fasteners: Stainless steel.
e.
Height: 16-5/8 inches (422 mm).
f.
Width: 27-5/16 inches (694 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
18.
DuMor 169 Series. Welded seat and back.
a.
End frames: Cast iron bench supports.
 
** NOTE TO SPECIFIER ** Armrest optional, delete if not required.
 
b.
Armrest: Cast Iron.
c.
Seats: 10 gauge slotted perforated steel
d.
Fasteners: Stainless steel.
e.
Height: 16-5/8 inches (422 mm).
f.
Width: 27-5/16 inches (694 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
19.
DuMor Bench 181-60:
a.
End frames: Cast aluminum bench supports.
b.
Seats: 10 gauge slotted perforated steel.
c.
Seat frame: Extruded aluminum channel.
d.
Fasteners: Stainless Steel.
e.
Height: 16-15/16 inches (430 mm).
f.
Width: 25-3/8 inches (645 mm).
g.
Length: 6 feet (1829 mm).
h.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
B.
Steel Benches without backrests.
1.
DuMor 92 Series. Welded seat and back.
a.
End frames: Cast iron bench supports.
b.
Seats: 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bars.
c.
Fasteners: Stainless steel.
d.
Bracing: 1-1/16 inch (29 mm) O.D. pipe.
e.
Height: 16-3/4 inches (425 mm).
f.
Width: 22-1/8 inches (562 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
2.
DuMor 95 Series. Welded seat and back.
a.
Supports: Cast iron bench supports.
b.
Seats: 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bars and 2-3/8 inch (60 mm) O.D. steel pipe.
c.
Fasteners: Stainless steel.
d.
Height: 17-9/16 inches (446 mm).
e.
Width: 22-3/16 inches (564 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
h.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
3.
DuMor 104 Series.
a.
End frames and Supports: 1/2 inch (12.5 mm) by 3 inch (76 mm) steel bar.
b.
Seats: 10 gauge perforated steel.
c.
Fasteners: Stainless steel.
d.
Height: 17-1/2 inches (445 mm).
e.
Width: 20 inches (508 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required and delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Surface plate.
2)
Gull wing.
3)
Sub-floor.
4)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
4.
DuMor 106 Series. One piece seat surface construction.
a.
End frames: Cast iron.
b.
Seats: 5/8 inch (15.9 mm) diameter steel bars.
c.
Fasteners: Stainless steel.
d.
Bracing: 1-1/16 inch (27 mm) O.D. pipe.
e.
Height: 16-3/4 inches (425 mm).
f.
Width: 22-1/8 inches (562 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
5.
DuMor 120 Series.
a.
End frames: Cast Iron
b.
Seats: 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar and 2-3/8 inch (60 mm) O. D. steel pipe.
c.
Bracing: 1-1/16 inch (27 mm) O.D. pipe.
d.
Fasteners: Stainless steel.
e.
Height: 18-3/4 inches (476 mm).
f.
Width: 22-1/4 inches (565 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
6.
DuMor 144 Series.
a.
End frames: Cast Iron.
b.
Seats: 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar and 2-3/8 inch (60 mm) O. D. steel pipe.
c.
Bracing: 1-1/16 inch (27 mm) O.D. pipe.
d.
Fasteners: Stainless steel.
e.
Height: 17 inches (432 mm).
f.
Width: 22-1/8 inches (562 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
7.
DuMor 145 Series.
a.
End frames: Cast Iron
b.
Seats: 5/8 inch (15.9 mm) diameter steel bars.
c.
Fasteners: Stainless steel.
d.
Height: 17 inches (432 mm).
e.
Width: 22-1/8 inches (562 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
h.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
8.
DuMor 164 Series.
a.
End frames: Cast Iron.
b.
Seats: 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar and 1-15/16 inch (60 mm) O.D. steel pipe.
c.
Fasteners: Stainless steel.
d.
Height: 16-7/8 inches (429 mm).
e.
Width: 22-3/8 inches (568 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
h.
Mounting: Provide with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
9.
DuMor 173 Series.
a.
End frames: Cast Iron.
b.
Seats: 3/8 inch (10 mm) diameter steel bar and 1-15/16 inch (60 mm) O.D. steel pipe.
c.
Fasteners: Stainless steel.
d.
Height: 16-7/8 inches (429 mm).
e.
Width: 22-3/8 inches (568 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
h.
Mounting: Provide with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm),stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
10.
DuMor Bench 174 series: welded seat:
a.
End frames: Cast iron bench supports.
b.
Seats: 10 gauge slotted perforated steel.
c.
Fasteners: Stainless Steel.
d.
Height: 16-3/4 inches (425 mm).
e.
Width: 22-1/4 inches (565 mm).
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
h.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
i.
Colors:
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
C.
Recycled plastic bench with backrest.
 
** NOTE TO SPECIFIER ** Select one of the following models. Delete model not used.
 
1.
DuMor Model 11PL:
a.
Supports: 2-7/8 inch (730 mm) O.D. steel pipe.
b.
Seat and Back: 4 inch by 4 inch (102 mm by 102 mm) recycled plastic with integral color.
c.
Fasteners: Stainless steel.
d.
Height: 17-15/16 inches (456 mm).
e.
Width: 24-15/16 inches (633 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Sub-Floor.
2)
Surface Plate.
3)
Embed 18 inches (457 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
2.
DuMor Model 57PL:
a.
End frames: Cast iron bench supports.
b.
Seat and Back: 2 inch by 3 inch (51 mm by 76 mm) recycled plastic with integral color.
c.
Seat Frame: 1/4 inch by 3 inch (6 mm by 76 mm) and 1/4 inch by 1-1/2 inch (6 mm by 38 mm) steel bar and 1 inch (25.5 mm) by 13 gauge square tube.
d.
Bracing: 1-1/16 inch (27 mm) steel pipe.
e.
Fasteners: Stainless steel.
f.
Height: 17 inches (432 mm).
g.
Width: 29-9/16 inches (751 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
h.
Length: 4 feet (1219 mm), 2 supports.
i.
Length: 6 feet (1829 mm), 2 supports.
j.
Length: 8 feet (2438 mm), 3 supports.
k.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Side panels are optional, delete if not required.
 
l.
Side Panels: Provide with custom lettered side panels as selected by the Architect.
m.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
n.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
3.
DuMor Model 88PL:
a.
Supports: 3/8 inch (10 mm) by 4-1/2 inch (114 mm) steel bar and 3 inch (76 mm) square by 1/4 inch (6 mm) wall steel tube.
b.
Seat and Back: 3 inch by 4 inch (76 mm by 102 mm) and profiled recycled plastic with integral color.
c.
Fasteners: Stainless steel.
d.
Height: 17-9/16 inches (446 mm).
e.
Width: 24-3/16 inches (614 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm), 2 supports.
g.
Length: 8 feet (2438 mm), 3 supports.
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Sub-Floor.
2)
Surface Plate.
3)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
4)
Gull wing.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
4.
DuMor Model 97: Team bench.
a.
Supports: 2-3/8 inch (61 mm) O.D. galvanized steel pipe.
 
** NOTE TO SPECIFIER ** Select one the following seat materials as required, delete the one not required.
 
b.
Seat and Back:
1)
2 inch by 10 inch (51 mm by 254 mm) recycled plastic with integral color and 1-5/16 inch (33 mm) O.D. galvanized pipe support.
2)
2 inch by 10 inch (51 mm by 254 mm) aluminum extrusion with a clear anodized finish. Bracing 1-5/16 inch (48 mm) O.D. galvanized steel pipe on plastic models only.
c.
Fasteners: Stainless steel.
d.
Height: 17-3/16 inches (437 mm).
e.
Width: 19-3/4 inches (502 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm), 2 supports.
g.
Length: 8 feet (2438 mm), 2 supports.
h.
Length: 12 feet (3658 mm), 3 supports.
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
i.
Mounting:
1)
Free Standing.
2)
Embed 18 inches (457 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
j.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
k.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
5.
DuMor Model 98PL:
a.
End frames: Cast iron bench supports.
b.
Seat and Back: 3 inch by 4 inch (76 mm by 102 mm) recycled plastic with integral color.
c.
Bracing: 1-1/16 (27 mm) O.D. steel pipe.
d.
Fasteners: Stainless steel.
e.
Height: 17-7/8 inches (454 mm).
f.
Width: 25-13/16 inches (656 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm), 3 supports.
h.
Length: 8 feet (2438 mm), 3 supports.
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
j.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
k.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
6.
DuMor Model 131PL:
a.
Supports: 1/2 inch (12.5 mm) by 3 inch (76 mm) steel.
b.
Seat and Back: 3 inch by 4 inch (76 mm by 102 mm) and profiled recycled plastic with integral color.
c.
Fasteners: Stainless steel.
d.
Height: 17-9/16 inches (446 mm).
e.
Width: 24-1/8 inches (613 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm), 3 supports.
g.
Length: 8 feet (2438 mm), 3 supports.
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Sub-Floor.
2)
Gull-Wing.
3)
Surface Plate.
4)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
7.
DuMor Model 138PL:
a.
Supports: 2 inch (51 mm) schedule 40 steel pipe and 3/8 inch (10 mm) by 4-1/2 inch (114 mm) steel bar.
b.
Seat and Back: 2 inch by 4 inch (51 mm by 102 mm) recycled plastic with integral color.
c.
Fasteners: Stainless steel.
d.
Height: 18 inches (457 mm).
e.
Width: 17-1/2 inches (445 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Sub-Floor.
2)
Surface Plate.
3)
Embed 18 inches (457 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
8.
DuMor Model 143PL:
a.
End frames: Cast iron bench supports.
b.
Seat and Back: 2 inch by 3 inch (51 mm by 76 mm) recycled plastic with integral color.
c.
Bracing: 1-1/16 (27 mm) O.D. steel pipe.
d.
Fasteners: Stainless steel.
e.
Height: 17-1/16 inches (433 mm).
f.
Width: 27-9/16 inches (700 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 4 feet (1219 mm), 2 supports.
h.
Length: 6 feet (1829 mm), 2 supports.
i.
Length: 8 feet (2438 mm), 3 supports.
j.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Side panels are optional, delete if not required.
 
k.
Side Panels: Provide with custom lettered side panels as selected by the Architect.
l.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
m.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
9.
DuMor Model 154PL:
a.
Supports: 3/8 inch (10 mm) by 4-1/2 inch (114 mm) by 1/2 inch 12.5 mm) steel bar.
b.
Seat and Back: 3 inch by 4 inch (76 mm by 102 mm) and profiled recycled plastic with integral color.
c.
Fasteners: Stainless steel.
d.
Height: 16-15/16 inches (427 mm).
e.
Width: 22-11/16 inches (576 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm), 3 supports.
g.
Length: 8 feet (2438 mm), 3 supports.
h.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
10.
Model 165PL:
a.
Supports: Cast Iron.
b.
Seat and Back: 2 inch by 3 inch (51 mm by 76 mm) recycled plastic with integral color.
c.
Frame: 1-15/16 inch (49 mm) schedule 40 steel pipe and 1/4 inch (6 mm) by 3 inch (76 mm) and 1/2 inch (12.5 mm) by 3 inch (76 mm) steel bar.
d.
Fasteners: Stainless steel.
e.
Height: 16-11/16 inches (423 mm).
f.
Width: 27-5/16 inches (693 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm) 2 supports.
h.
Length: 8 feet (2438 mm) 2 supports.
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
j.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
k.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
11.
DuMor Model 177PL:
a.
Supports: 1-1/2 inch (38 mm) schedule 40 steel pipe and 3/8 inch (9.5 mm) steel plate.
b.
Seat and Back: 2 inch by 3 inch (51 mm by 76 mm) recycled plastic with integral color.
c.
Fasteners: Stainless Steel.
d.
Height: 17-1/16 inches (433 mm).
e.
Width: 26-1/16 inches (662 mm).
f.
Length: 4 feet (1219 mm).
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting:
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required.
 
1)
Sub floor
2)
Surface Plate
3)
Embed 18 inches (457mm) into a cast in place concrete foundation as specified in section 03 30 00 - Cast-in-Place Concrete.
j.
Plastic colors: As selected by the Architect from the manufacturer's 5 standard colors.
k.
Frame Colors:
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
12.
DuMor Model 185PL:
a.
End Frames: Cast iron bench supports.
b.
Seat and Back: 2 inch by 3 inch (51 mm by 76 mm) recycled plastic with integral color.
c.
Seat frame: 1/4 by 3 inch (6 mm by 76 mm) and 1/4 by 1-1/2 inch (6 mm by 38 mm) steel bar.
d.
Fasteners: Stainless Steel.
e.
Height: 17-13/16 inches (453 mm).
f.
Width: 22-5/16 inches (567 mm).
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm) stainless steel anchor bolts.
j.
Plastic colors: As selected by the Architect from the manufacturer's 5 standard colors.
k.
Frame Colors:
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
D.
Recycled plastic bench without backrest.
1.
Model 91PL:
a.
Supports: Cast Iron.
b.
Seat members: 2 inch by 3 inch (51 mm by 76 mm) recycled plastic with integral color.
c.
Frame: 1/4 inch (6 mm) by 3 inch (76 mm) and 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar and 1 inch (25 mm) by 13 gauge square tube.
d.
Bracing: 1-1/16 inch (73 mm) O.D. steel pipe.
e.
Fasteners: Stainless steel.
f.
Height: 16-3/4 inches (425 mm).
g.
Width: 22-1/8 inches (560 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
h.
Length: 4 feet (1219 mm) with 2 supports.
i.
Length: 6 feet (1829 mm) with 2 supports.
j.
Length: 8 feet (2438 mm) with 3 supports.
k.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
l.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
m.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
 
** NOTE TO SPECIFIER ** Select one of the following models. Delete model not used.
 
2.
DuMor Model 99:
a.
Supports: 2-3/8 inch (60 mm) O.D. steel pipe and 1 inch (25 mm) by 2 inch (51 mm) by 3/16 inch steel angle.
b.
Seat:
1)
2 inch by 10 inch (51 mm by 254 mm) recycled plastic with integral color and a 1-5/16 inch (33 mm) O.D. galvanized pipe support.
2)
2 inch by 10 inch (51 mm by 254 mm) aluminum extrusion with a clear anodized finish.
c.
Fasteners: Stainless steel.
d.
Height: 17-1/4 inches (438 mm).
e.
Width: 9-1/2 inches (241 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
h.
Length: 12 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
i.
Mounting:
1)
Free Standing.
2)
Embed 18 inches (457 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
j.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
k.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
3.
DuMor Model 103PL:
a.
Supports: 1/2 inch (12.5 mm) by 3 inch (76 mm) steel bar and 3 inch (76 mm) square by 1/4 inch (6 mm) wall steel tube.
b.
Seat: 3 inch by 4 inch (76 mm by 102 mm) recycled plastic with integral color.
c.
Fasteners: Stainless steel.
d.
Height: 18 inches (457 mm).
e.
Width: 19-1/2 inches (495 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm), 2 supports.
g.
Length: 8 feet (2438 mm), 3 supports.
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Sub-Floor.
2)
Gull-Wing.
3)
Surface Plate.
4)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
4.
DuMor Model 105PL:
a.
Supports: 2-7/8 inch (73 mm) O.D. galvanized steel pipe and 3/8 inch (10 mm) by 4-1/2 inch (114 mm) steel plate.
b.
Seat: 4 inch by 4 inch (102 mm by 102 mm) recycled plastic with integral color.
c.
Fasteners: Stainless steel.
d.
Height: 18 inches (457 mm).
e.
Width: 15-1/2 inches (394 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm), 2 supports.
g.
Length: 8 feet (2438 mm), 2 supports.
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Free Standing.
2)
Sub Floor.
3)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
5.
DuMor Model 132PL:
a.
Supports: 1/2 inch (12.5 mm) by 3 inch (76 mm) steel.
b.
Seat: 3 inch by 4 inch (76 mm by 102 mm) and profiled recycled plastic with integral color.
c.
Fasteners: Stainless steel.
d.
Height: 18 inches (457 mm).
e.
Width: 19-1/2 inches (495 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm), 3 supports.
g.
Length: 8 feet (2438 mm), 3 supports.
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Sub-Floor.
2)
Gull-Wing.
3)
Surface Plate.
4)
Embed 19-7/8 inches (505 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
6.
DuMor Model 139PL:
a.
Supports: 2-3/8 inch (61 mm) O.D. schedule 40 steel pipe and 3/8 inch (10 mm) by 4-1/2 (114 mm) inch steel bar.
b.
Seat: 2 inch by 4 inch (51 mm by 102 mm) recycled plastic with integral color.
c.
Fasteners: Stainless steel.
d.
Height: 18 inches (457 mm).
e.
Width: 15-1/2 inches (394 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm), 2 supports.
g.
Length: 8 feet (2438 mm), 2 supports.
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Free Standing.
2)
Sub-Floor.
3)
Embed 18 inches (457 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
7.
DuMor Model 147PL:
a.
Supports: Cast iron bench supports.
b.
Seat: 2 inch by 3 inch (51 mm by 76 mm) recycled plastic with integral color.
c.
Frame: 1/4 inch (6 mm) by 3 inch (76 mm) and 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar and 1 inch (25 mm) by 13 gauge square tube.
d.
Bracing: 1-1/16 (27 mm) O.D. steel pipe.
e.
Fasteners: Stainless steel.
f.
Height: 17 inches (432 mm).
g.
Width: 22-1/8 inches (562 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
h.
Length: 4 feet (1219 mm), 2 supports.
i.
Length: 6 feet (1829 mm), 2 supports.
j.
Length: 8 feet (2438 mm), 3 supports.
k.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
l.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
m.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
8.
DuMor Model 155PL:
a.
Supports: 3/8 inch (10 mm) by 4-1/2 inch (114 mm) by 1/2 inch 12.5 mm) steel bar.
b.
Seat: 3 inch by 4 inch (76 mm by 102 mm) and profiled recycled plastic with integral color.
c.
Fasteners: Stainless steel.
d.
Height: 17 inches (432 mm).
e.
Width: 20-11/16 inches (525 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm), 3 supports.
g.
Length: 8 feet (2438 mm), 3 supports.
h.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
9.
DuMor Model 163PL:
a.
Supports: 3/8 inch (10 mm) by 4-1/2 inch (114 mm) steel bar and 3 inch (76 mm) square by 1/4 inch (6 mm) wall steel tube.
b.
Seat: 2 inch by 3 inch (51 mm by 76 mm) and 3 inch by 4 inch (76 by 102 mm) recycled plastic with integral color separated by nylon spacers. Plated 1/2 inch (12.5 mm) diameter interior steel rods capped with matching plastic plugs.
c.
Fasteners: Stainless steel.
d.
Height: 17 inches (432 mm).
e.
Width: 19-13/16 inches (503 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Sub-Floor.
2)
Gull-Wing.
3)
Surface Plate.
4)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
i.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
10.
Model 166PL:
a.
Supports: Cast Iron.
b.
Seat: 2 inch by 3 inch (51 mm by 76 mm) recycled plastic with integral color.
c.
Frame: 1-15/16 inch (49 mm) O.D. schedule 40 steel pipe.
d.
Fasteners: Stainless steel.
e.
Height: 16-15/16 inches (431 mm).
f.
Width: 22-3/8 inches (568 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm) 2 supports.
h.
Length: 8 feet (2438 mm) 2 supports.
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
j.
Plastic Colors: As selected by the Architect from manufacturer's 5 standard colors.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
k.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
11.
DuMor Model 178PL:
a.
Supports: 1-1/2 inch (38 mm) schedule 40 steel pipe and 1/4 by 1/2 inch (6 mm by 12.5 mm) steel plate.
b.
Seat: 2 inch by 3 inch (51 mm by 76mm) recycled plastic with integral color.
c.
Fasteners: Stainless Steel
d.
Height: 17-1/16 inches (434 mm)
e.
Width: 21 inches (533 mm)
f.
Length: 4 feet (1219 mm)
g.
Length: 6 feet (1829 mm)
h.
Length: 8 feet (2438 mm)
i.
Mounting:
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required.
 
1)
Sub floor
2)
Surface Plate
3)
Embed 18 inches (457mm) into a cast in place concrete foundation as specified in section 03 30 00 - Cast-in-Place Concrete.
j.
Plastic colors: As selected by the Architect from the manufacturer's 5 standard colors.
k.
Frame Colors:
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
12.
DuMor Model 186PL:
a.
End Frames: Cast iron bench supports.
b.
Seat: 2 inch by 3 inch (51 mm by 76mm) recycled plastic with integral color.
c.
Seat frame: 1/4 by 3 inch (6 mm by 76 mm) and 1/4 by 1-1/2 inch (6 mm by 38 mm) steel bar.
d.
Fasteners: Stainless Steel.
e.
Height: 17-1/4 inches (438 mm).
f.
Width: 17-1/4 inches (438 mm).
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm) stainless steel anchor bolts.
j.
Plastic colors: As selected by the Architect from the manufacturer's 5 standard colors.
k.
Frame Colors:
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
E.
Wood benches with backrest.
1.
Model 34:
a.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 mm by 76 mm) Redwood.
2)
2 inch by 3 inch (51 mm by 76 mm) Douglas Fir.
b.
Frame: 3/8 inch (10 mm) by 4-1/2 inch (114 mm) steel bar and 2-1/2 inch (64 mm) by 1/4 inch (6 mm) square steel tube.
c.
Fasteners: Stainless steel.
d.
Height: 17-1/2 inches (445 mm).
e.
Width: 24-1/16 inches (611 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Gull-Wing.
2)
Sub-Floor.
3)
Surface Plate.
4)
Embed 18 inches (457 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
2.
Model 35:
a.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
3 inch by 3 inch (76 mm by 76 mm) and 3 inch by 4 inch (76 mm by 102 mm) Redwood.
2)
3 inch by 3 inch (76 mm by 76 mm) and 3 inch by 4 inch (76 mm by 102 mm) Douglas Fir.
b.
Frame: 1/2 inch (12.5 mm) by 3 inch (76 mm) steel bar and 2 inch (51 mm) by 3/8 inch (10 mm) steel bar.
c.
Fasteners: Stainless steel.
d.
Height: 17-1/2 inches (445 mm).
e.
Width: 23-9/16 inches (598 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Gull-Wing.
2)
Sub-Floor.
3)
Surface Plate.
4)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
3.
Model 39:
a.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 by 76 mm) and 3 inch by 4 inch (76 mm by 102 mm) Redwood.
2)
2 inch by 3 inch (51 by 76 mm) and 3 inch by 4 inch (76 mm by 102 mm) Douglas Fir.
b.
Frame: 1/2 inch (12.5 mm) by 3 inch (76 mm) steel bar and 2-1/2 inch (62 mm) by 1/4 inch (6 mm) square steel tube with 3/8 inch (10 mm) by 1 inch (25 mm) steel contour straps.
c.
Fasteners: Stainless steel.
d.
Height: 17-1/8 inches (433 mm).
e.
Width: 23 inches (584 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Gull-Wing.
2)
Sub-Floor.
3)
Surface Plate.
4)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
4.
Model 51:
a.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 4 inch (51 mm by 102 mm) and 4 inch by 4 inch (102 mm by 102 mm) Redwood.
2)
2 inch by 4 inch (51 mm by 102 mm) and 4 inch by 4 inch (102 mm by 102 mm) Douglas Fir.
b.
Frame: 3/8 inch (10 mm) by 4-1/2 inch (114 mm) steel bar and 3 inch (76 mm) by 1/4 inch (6 mm) wall square steel tube.
c.
Fasteners: Stainless steel.
d.
Height: 17-1/2 inches (445 mm).
e.
Width: 26-3/8 inches (670 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Gull-Wing.
2)
Sub-Floor.
3)
Surface Plate.
4)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
5.
Model 56:
a.
Supports: 2-7/8 inch (73 mm) O.D. steel pipe.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
4 inch by 4 inch (102 mm by 102 mm) Redwood.
2)
4 inch by 4 inch (102 mm by 102 mm) Douglas Fir.
c.
Fasteners: Stainless steel.
d.
Height: 18 inches (457 mm).
e.
Width: 24-15/16 inches (630 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Sub-Floor.
2)
Surface Plate.
3)
Embed 18 inches (457 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
6.
Model 57:
a.
End Frames: Cast Iron.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 mm by 76 mm) Redwood.
2)
2 inch by 3 inch (51 mm by 76 mm) Douglas Fir.
3)
2 inch by 3 inch (51 mm by 76 mm) Ipe.
c.
Bracing: 1-1/16 inch (27 mm) O.D. steel pipe.
d.
Fasteners: Stainless steel.
e.
Height: 17 inches (432 mm).
f.
Width: 27-9/16 inches (700 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Side panels are optional, delete if not required.
 
j.
Side Panels: Provide with custom lettered side panels as selected by the Architect.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
k.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
7.
Model 79:
a.
Supports: 2-3/8 inch (60 mm) O.D. steel pipe.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 4 inch (51 mm by 102 mm) Redwood.
2)
2 inch by 4 inch (51 mm by 102 mm) Douglas Fir.
c.
Fasteners: Stainless steel.
d.
Height: 17 inches (432 mm).
e.
Width: 19-5/16 inches (491 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm) with two supports.
g.
Length: 8 feet (2438 mm) with three supports.
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Sub-Floor.
2)
Surface Plate.
3)
Embed 18 inches (457 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
8.
Model 88:
a.
Supports: 3/8 inch (10 mm) by 4-1/2 inch (114 mm) steel bar and 3 inch (76 mm) square by 1/4 inch (6 mm) wall steel tube.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
3 inch by 4 inch (76 mm by 102 mm) Redwood.
2)
3 inch by 4 inch (76 mm by 102 mm) Douglas Fir.
c.
Fasteners: Stainless steel.
d.
Height: 17-7/16 inches (423 mm).
e.
Width: 21-7/8 inches (556 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Gull-Wing.
2)
Sub-Floor.
3)
Surface Plate.
4)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
9.
Model 98:
a.
Supports: Cast Iron.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 4 inch (51 mm by 102 mm) Redwood.
2)
2 inch by 4 inch (51 mm by 102 mm) Douglas Fir.
3)
3 inch by 4 inch (76 mm by 102 mm) Redwood.
4)
3 inch by 4 inch (76 mm by 102 mm) Douglas Fir.
c.
Bracing: 1-1/16 inch (27 mm) O. D. steel pipe.
d.
Fasteners: Stainless steel.
 
** NOTE TO SPECIFIER ** Select one the following heights and delete the one not required. Use 16-7/8 for 2 by 4 wood and 17-7/8 for 3 by 4 wood seat members.
 
e.
Height: 16-7/8 inches (429 mm).
f.
Height: 17-7/8 inches (454 mm).
g.
Width: 25-13/16 inches (656 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
h.
Length: 6 feet (1829 mm) 2 supports.
i.
Length: 8 feet (2438 mm) 3 supports.
j.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
k.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
10.
Model 142:
a.
Supports: Cast Iron.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 mm by 76 mm) Redwood.
2)
2 inch by 3 inch (51 mm by 76 mm) Douglas Fir.
3)
2 inch by 3 inch (51 mm by 76 mm) Ipe.
c.
Bracing/Straps: 1-1/16 inch (27 mm) O. D. steel pipe and 1/4 inch (6 mm) by 3 inch (76 mm) steel bar and 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar.
d.
Fasteners: Stainless steel.
e.
Height: 17-1/16 inches (433 mm).
f.
Width: 27-9/16 inches (700 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm) 2 supports.
h.
Length: 8 feet (2438 mm) 2 supports.
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Side panels are optional, delete if not required.
 
j.
Side Panels: Provide with custom lettered side panels as selected by the Architect.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
k.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
11.
Model 165:
a.
Supports: Cast Iron.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 mm by 76 mm) Redwood.
2)
2 inch by 3 inch (51 mm by 76 mm) Douglas Fir.
3)
2 inch by 3 inch (51 mm by 76 mm) Ipe.
c.
Frame: 1-15/16 inch (49 mm) schedule 40 steel pipe and 1/4 inch (6 mm) by 3 inch (76 mm) and 1/2 inch (12.5 mm) by 3 inch (76 mm) steel bar.
d.
Fasteners: Stainless steel.
e.
Height: 16-11/16 inches (423 mm).
f.
Width: 27-5/16 inches (693 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm) 2 supports.
h.
Length: 8 feet (2438 mm) 2 supports.
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
12.
DuMor Model 185:
a.
End Frames: Cast iron bench supports.
b.
Wood seat and back members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 mm by 76 mm) Redwood.
2)
2 inch by 3 inch (51 mm by 76 mm) Douglas Fir.
3)
2 inch by 3 inch ( 51 mm by 76 mm) Ipe.
c.
Seat frame: 1/4 inch by 3 inch (6 mm by 76 mm) and 1/4 inch by 1-1/2 inch (6 mm by 38 mm) steel bar.
d.
Fasteners: Stainless Steel.
e.
Height: 17-13/16 inches (452 mm).
f.
Width: 22-5/16 inches (567 mm).
g.
Length: 6 feet (1829mm)
h.
Length: 8 feet (2438mm)
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm) stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
F.
Wood benches without backrest.
1.
Model 37:
a.
Supports: 3 inch (76 mm) by 1/4 inch (6 mm) square steel tube with 3/8 inch (10 mm) by 4-1/2 inch (114 mm) steel bar.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 mm by 76 mm) and 3 inch by 6 inch (76 mm by 152 mm) Redwood.
2)
2 inch by 3 inch (51 mm by 76 mm) and 3 inch by 6 inch (76 mm by 152 mm) Douglas Fir.
c.
Fasteners: Stainless steel.
d.
Height: 17 inches (432 mm).
e.
Width: 19-13/16 inches (503 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Gull-Wing.
2)
Sub-Floor.
3)
Surface Plate.
4)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
2.
Model 53:
a.
Supports: 1/2 inch (12.5 mm) by 3 inch (76 mm) steel bar and 2 inch (51 mm) by 3/8 inch (10 mm) steel bar.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
3 inch by 3 inch (76 mm by 76 mm) and 3 inch by 4 inch (76 mm by 102 mm) Redwood.
2)
3 inch by 3 inch (76 mm by 76 mm) and 3 inch by 4 inch (76 mm by 102 mm) Douglas Fir.
c.
Fasteners: Stainless steel.
d.
Height: 17-1/2 inches (445 mm).
e.
Width: 18-15/16 inches (481 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Gull-Wing.
2)
Sub-Floor.
3)
Surface Plate.
4)
Embed 24 inches (610 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
3.
Model 91:
a.
Supports: Cast Iron.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 mm by 76 mm) Redwood.
2)
2 inch by 3 inch (51 mm by 76 mm) Douglas Fir.
3)
2 inch by 3 inch (51 mm by 76 mm) Ipe.
c.
Frame: 1/4 inch (6 mm) by 3 inch (76 mm) and 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar.
d.
Bracing: 1-1/16 inch (73 mm) O.D. steel pipe.
e.
Fasteners: Stainless steel.
f.
Height: 16-3/4 inches (425 mm).
g.
Width: 22-1/8 inches (560 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
h.
Length: 6 feet (1829 mm).
i.
Length: 8 feet (2438 mm).
j.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
k.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
4.
Model 105:
a.
Supports: 3/8 inch (10 mm) by 4-1/2 inch (114 mm) steel bar and 2-7/8 inch (73 mm) O.D. steel pipe.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
4 inch by 4 inch (102 mm by 102 mm) Redwood.
2)
4 inch by 4 inch (102 mm by 102 mm) Douglas Fir.
c.
Fasteners: Stainless steel.
d.
Height: 18 inches (457 mm).
e.
Width: 15-1/2 inches (394 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
f.
Length: 6 feet (1829 mm).
g.
Length: 8 feet (2438 mm).
 
** NOTE TO SPECIFIER ** Select one the following mounting types as required and delete those not required.
 
h.
Mounting:
1)
Sub-Floor.
2)
Surface Plate.
3)
Embed 19-7/8 inches (505 mm) into a cast in place concrete foundation as specified is Section 03 30 00 - Cast-in-Place Concrete.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
i.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
5.
Model 146:
a.
Supports: Cast Iron.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 mm by 76 mm) Redwood.
2)
2 inch by 3 inch (51 mm by 76 mm) Douglas Fir.
3)
2 inch by 3 inch (51 mm by 76 mm) Ipe.
c.
Bracing/Straps: 1-1/16 inch (27 mm) O. D. steel pipe and 1/4 inch (6 mm) by 3 inch (76 mm) and 1/4 inch (6 mm) by 1-1/2 inch (38 mm) steel bar.
d.
Fasteners: Stainless steel.
e.
Height: 17 inches (432 mm).
f.
Width: 22-7/8 inches (581 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm) 2 supports.
h.
Length: 8 feet (2438 mm) 2 supports.
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
j.
Frame Colors:
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
6.
Model 166:
a.
Supports: Cast Iron.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 mm by 76 mm) Redwood.
2)
2 inch by 3 inch (51 mm by 76 mm) Douglas Fir.
3)
2 inch by 3 inch (51 mm by 76 mm) Ipe.
c.
Frame: 1-15/16 inch (49 mm) O.D. schedule 40 steel pipe.
d.
Fasteners: Stainless steel.
e.
Height: 16-15/16 inches (431 mm).
f.
Width: 22-3/8 inches (568 mm).
 
** NOTE TO SPECIFIER ** Select one the following lengths as required, delete those not required.
 
g.
Length: 6 feet (1829 mm) 2 supports.
h.
Length: 8 feet (2438 mm) 2 supports.
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm), stainless steel anchor bolts.
j.
Frame Colors:
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
7.
DuMor Model 186
a.
End Frames: Cast iron bench supports.
b.
Wood seat members:
 
** NOTE TO SPECIFIER ** Select one the following wood seat sizes and materials, delete those not required.
 
1)
2 inch by 3 inch (51 mm by 76 mm) Redwood.
2)
2 inch by 3 inch (51 mm by 76 mm) Douglas Fir.
3)
2 inch by 3 inch (51 mm by 76 mm) Ipe.
c.
Seat frame: 1/4 by 3 inch (6 mm by 76 mm) and 1/4 by 1-1/2 inch (6 mm by 38 mm) steel bar.
d.
Fasteners: Stainless Steel.
e.
Height: 17-1/4 inches (438 mm).
f.
Width: 17-1/4 inches (438 mm).
g.
Length: 6 feet (1829 mm).
h.
Length: 8 feet (2438 mm).
i.
Mounting: Provided with 1/2 inch (12.5 mm) by 3-3/4 inch (95 mm) stainless steel anchor bolts.
j.
Frame Colors:
 
** NOTE TO SPECIFIER ** Select one the following paragraphs as required, delete those not required. Custom colors are available at additional cost.
 
1)
As selected by the Architect from manufacturer's 11 standard powder coated colors.
2)
Custom color as selected by the Architect.
PART 3 EXECUTION
 
3.1
EXAMINATION
A.
Do not begin installation until substrates have been properly prepared.
B.
If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
3.2
PREPARATION
A.
Clean surfaces thoroughly prior to installation.
B.
Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
3.3
INSTALLATION
A.
Install in accordance with manufacturer's instructions.
B.
Embedded mounting. Material is to be extended a minimum of 12 inches (305 mm) below finish surface and cast in concrete.
C.
Surface mounting. Location and drilling of holes for inserts included. Anchor bolts and inserts provided by others.
3.4
PROTECTION
A.
Protect installed products until completion of project.
B.
Touch-up, repair or replace damaged products before Substantial Completion.
END OF SECTION