| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| 1. Configure Mapei Corporation - CONCRETE RESURFACING AND REHABILITATION: |
| INTERIOR/EXTERIOR PRODUCTS |
| | Fast-Drying Non-Shrink Topping: Mapei Mapecem mixed with aggregate & water; allows traffic within 3-4 hours of |
| | applying; dries in 24 hours; for 3/8 in - 1-3/8 in monolithic topping or 1-3/8 in min. floating topping |
| | Fast-Setting Topping: Pre-blended, cementitious; for horizontal surfaces, allowing traffic or subsequent finishing
within 3-4 hours |
 | | | Mapei Mapecem 202: Two component, non-shrinking, self curing; 1/4 in - 2 in per coat, or aggregate
extended to 8'' thickness |
| | | Mapei Mapecem 100: One component, abrasion resistant; for 3/8 in - 4 in thick monolithic topping or
1-3/8 in - 4 in thick floating topping |
| | | Mapei Mapecem 102: One component, non shrinking, self-curing; for horizontal surfaces, 1/4 in - 2 in per
coat, or aggregate extended to 8 in thickness |
| | | Mapei Mapecem 101: One component, non-shrinking, self-curing; for horizontal surfaces, feather edge to 1 in
per coat |
| | Fluid Topping: Pre-blended two component polymer-modified high strength flowable cementitious topping mortar;
Mapei Planitop 25; 1/4 in - 1 in per coat |
| | Traffic Surface Repair Mortar: Pre-blended cementitious mortar suitable for vehicular traffic |
| | | Mapei Planitop 16: One-component magnesium phosphate concrete, abrasion resistant, allows vehicular
traffic in 45 minutes, suitable for large repair areas |
| | | Mapei Planitop 18: One component high-early-strength, shrinkage-compensated, allowing vehicular traffic
within 60 minutes; for small area repairs |
| | Exterior/Interior Repair Mortar: Pre-blended polymer-modified, cementitious patching mortar; for vertical,
horizontal, and ceiling surfaces |
| | | Mapei Planitop 12: One component, shrinkage-compensated, thixotropic mortar with fiber reinforcement; min.
1/4 in thickness |
| | | Mapei Planitop 23: Two component, fast-setting, thixotropic, with fiber reinforcement; 1/8 in - 1-5/8 in per coat |
| | | Mapei Planitop X: One component fast setting, shrinkage compensated, fiber reinforced horizontal, vertical
and overhead repair mortar; feather edge to 4 in per coat |
| | | Mapei Planitop 21: Two component; maximum 1/4 in per coat |
| | | Primer: As recommended by manufacturer |
| | Very Fluid Repair Mortar: Pre-blended one-component shrinkage-compensated cementitious fiber-reinforced
mortar; Mapei Planitop 15 |
| | Quick-Set Anchoring Mortar: Pre-blended cementitious quick-set hydraulic cement mortar; Mapei Quickcem Plug |
| | Hydraulic Plug Mortar: Pre-blended cementitious quick-set hydraulic cement mortar; Mapei Planiseal Plug |
| | Structural Grout: Pre-blended high strength shrinkage-compensated cementitious grout; ASTM C 1107 Grade C
and COE CRD-C 621 Grade C |
| | | Mapei Planigrout 740: capable of being placed in consistencies from plastic to very fluid |
| | | Mapei Planigrout 750: capable of being placed in consistencies from dry pack to very fluid |
| | Rebar Primer: 3 component epoxy cemntitious, with corrosion inhibitors; Mapei Planibond 3C |
| | Epoxy Adhesive: Two-component, non-shrink, solvent-free, moisture-insensitive epoxy adhesive |
| | | Mapei Planibound EBA |
| | | Mapei Planibound E Gel: thixotropic structural adhesive |
| | Slurry Bond Coat: Portland cement, sand, and Mapei Planicrete AC, SB, or PM mix; proportions as recommended
by manufacturer |
| | Curing Compound: White pigmented water-borne resin-based liquid curing compound, ASTM C 309 Type I Class B
and AASHTO M148 Type II Class B; Mapei Planicure 65 |
| INTERIOR PRODUCTS |
| | Self-Leveling Exposed Topping: Pre-blended, cementitious; self-curing, Mapei Ultratop; for over concrete;
min. thickness 1/4 in |
| | | Color: |
| | | Primer: As recommended by manufacturer |
| | The following toppings are intended as underlayment for a finish floor material such as carpet, ceramic tile, or
resilient flooring. Not suitable for dimensionally unstable substrates. |
| | Self-Leveling fast track Underlayment: Pre-blended cementitious, for fast track floor covering installation |
| | | Mapei Ultraplan M20: fast setting; for over concrete and exterior grade plywood, 1/4'' to 2'' |
| | | Mapei Ultraplan 1: fast setting; for over cured concrete and exterior grade plywood, feather edge to 1-1/2'' |
| | | Primer: As recommended by topping manufacturer |
| | Self-Leveling Underlayment: Pre-blended cementitious, for thickness from feather edge |
| | | Mapei Ultraplan M20: fast setting; for over concrete and exterior grade plywood, 1/4'' to 2'' |
| | | Mapei Ultraplan 1: fast setting, polymer modified; for over cured concrete, plywood, ceramic tile, old cutback
adhesive, vinyl, feather edge to 1-1/2" |
| | | Mapei Novoplan 2: normal setting, polymer-modified; for over cured concrete, feather edge to 1/2'' |
| | | Mapei Novo/Plan 6: normal setting; for over cured concrete, feather edge to 1/2'' |
| | | Primer: As recommended by topping manufacturer |
| | Interior Repair Mortar: Pre-blended cementitious patching for concrete |
| | | Mapei Planitop X: one component, fast setting, polymer-modified, synthetic fiber reinforced; for vertical and
horizontal surfaces, featheredge to 4 in for patching voids |
| | | Mapei Mapecem 101: one-component, fast-setting, non-shrinking, self-curing; for horizontal surfaces, feather
edge to 1 inch (25 mm) per coat |
| | | Mapei Planipatch/Planipatch Plus: two-component, fast-setting; for floor surfaces, feather edge to 1/4 in
(6 mm) thick |
| | | Mapei Ultraskim Coat: one-component, fast-setting; for floor surfaces, feather edge to 1/4 in
(6 mm) thick |
| | | Mapei Portland cement, sand, and Mapei Planicrete AC or SB mix; for minimum 3/8 in thickness |
| | | Primer: As recommended by topping manufacturer |
| | Interior moisture reduction Barrier: Planiseal MRB; A two-component, solvent-free fluid-applied breathable epoxy |
| 2. When you are finished making selections |
| Generate Spec:  Word  WP or  RTF |