1. Configure SEAL-KRETE PENETRATING SEALER:

MATERIALS

Waterproof Sealer:  Clear, non-staining, waterborne acrylic-base penetrating sealerprimer containing

low quantities of VOCs (volatile organic compounds); SEAL-KRETE Waterproofing Sealer.

Resistance to Water Penetration:  Minimum rating of Excellent, when tested according to

FS TT-P-0035, modified using 4 by 8 by 16 inch (100 by 200 by 400 mm) concrete block,

at equivalent of 98 mph (158 km/h) wind speed

Water Vapor Transmission:  3.6 perms (207 ng/(Pa s sqm), maximum, when tested

in accordance with ASTM D 1653.

Corrosion Resistance:  No visible degradation of film after 48 hours, when subjected to

sodium hypochlorite, hydrochloric acid, sodium chloride (salt), and chlorine.

Solids Content:  25 percent, minimum.

Flammability:  Non-flammable.

Toxicity:  USDA approved for application to surfaces where there is possibility of contact with food.

Tensile Strength:  1000 psi (6890 kPa).

Freeze/Thaw Stability:  Stable.

Fading Resistance:  Approximately 0.05 percent, maximum, after 312 hours of testing.

Comply with Florida Department of Transportation Specification 926-16 for Type 'O' Compounds,

Florida DOT Method FM5-518.

Pigmenting Agent: SELECT PIGMENTING AGENT-----------Latex-based paint, specified in Section 09900Latex-based stain, specified in Section 09900

Heavy Duty Commercial Grade Waterproofer:  Advanced, high-solids, siliconized, acrylic blend designed to protect and strengthen bare,

porous concrete and masonry, such as split-face or fluted concrete block.

Resistance to Water Penetration:  No more than 25 percent dampness appearing on back of wall specimen,

when tested in accordance with ASTM E 514 for 4 hours.

Solids Content: 25 percent minimum.

Meets FS SS-W-110C for Water Repellency on Masonry.

Mildew Resistance: ASTM D 5590.

Flammability: Non-flammable.

Toxicity: USDA approved for application to surfaces where there is possibility of contact with food.

APPLICATION

Apply Non-Pigmented Sealer to the Following Surfaces:

New foundation walls as primer for subsequent installation of waterproofing specified in Section 07140 Existing foundation walls as primer for subsequent installation of waterproofing specified in Section 07140

New vertical cast-in-place concrete surfaces Existing vertical cast-in-place concrete surfaces New vertical precast concrete surfaces Existing vertical precast concrete surfaces New tilt-up concrete panel surfaces Existing tilt-up concrete panel surfaces New concrete masonry unit surfaces Existing concrete masonry unit surfaces New brick masonry surfaces Existing brick masonry surfaces New stone masonry surfaces Existing stone masonry surfaces New galvanized metal surfaces Existing galvanized metal surfaces New vertical wood surfaces Existing vertical wood surfaces New vinyl siding Existing vinyl siding New stucco surfaces Existing stucco surfaces New plaster surfaces Existing plaster surfaces New adobe surfaces Existing adobe surfaces New drywall surfaces Existing drywall surfaces New ceramic tile grout joints Existing ceramic tile grout joints Substrates to receive wallcoverings Low density block Split-face block Fluted block Limestone

Apply Sealer, Mixed with Specified Pigmenting Agent in accordance with manufaturer's instructions,

to the Following Surfaces:

New vertical cast-in-place concrete surfaces Existing vertical cast-in-place concrete surfaces New vertical precast concrete surfaces Existing vertical precast concrete surfaces New tilt-up concrete panel surfaces Existing tilt-up concrete panel surfaces New concrete masonry unit surfaces Existing concrete masonry unit surfaces New brick masonry surfaces Existing brick masonry surfaces New stone masonry surfaces Existing stone masonry surfaces New galvanized metal surfaces Existing galvanized metal surfaces New vertical wood surfaces Existing vertical wood surfaces New stucco surfaces Existing stucco surfaces New plaster surfaces Existing plaster surfaces New adobe surfaces Existing adobe surfaces New drywall surfaces Existing drywall surfaces Substrates to receive wallcoverings Low density block Split-face block Fluted block Limestone

2. When you are finished making selections:

Generate Spec: Word     WP   or   RTF