1. Configure Ludowici Roof Tile ROOF TILE:

ROOF TILE

A. Clay Roof Tile - General

Color:SELECT COLOR---------------Selected from full range of mfg's available colorsColor: __________Custom Color __________Multi-Color Custom SequenceColor A: _________Color B: _________Color C: _________Specified in SCHEDULES Article of this section

B. Flat Shingle Clay Roof Tile Type __:

Acceptable Products:

Antique Tile Brittany Tile Calais Tile Colonial Tile Crude Tile Georgian Tile Norman Tile Provincial Tile Flat Slab Shingle Tile

C. Interlocking Clay Roof Tile Type __:

Acceptable Products:

Americana Tile Americana XL Tile Classic Tile Classic XL Tile Lanai Tile Lanai XL Tile Williamsburg Tile Williamsburg XL Tile Imperial Tile

D. Interlocking Profile Clay Roof Tile Type __:

Acceptable Products:

French Tile National French 6 in Conosera Tile 8 in Conosera Tile 10 in Conosera Tile

E. Mission/Pan and Cover Clay Roof Tile Type __:

Choose 1 of the Following Acceptable Products:

Straight Barrel Mission Tile

Pan & Cover Nominal & Avg Exposure Length:SELECT LENGTH---------------Nominal Length: 14-1/4 in; Avg. Exposure Length: 11-1/4 inNominal Length: 16 in; Avg. Exposure Length: 13 inNominal Length: 18-3/8 in; Avg. Exposure Length: 15-3/8 in

Tapered Mission Tile

Pan Type:SELECT PAN---------------Straight Pan: Cover-to-cover centerline width of 10 in (254 mm)Tapered Pan: Cover-to-cover centerline width of 9-1/2 in (241 mm)

Pan & Cover Nominal & Avg Exposure Length:SELECT LENGTH---------------Nominal Length: 16 in; Avg. Exposure Length: 13 inNominal Length: 18-3/8 in; Avg. Exposure Length: 15-3/8 in

Greek Tile

Italian Tile

Cover Type:SELECT COVER---------------Straight, nominal length __ inches (__ mm)Tapered, nominal length __ inches (__ mm)

Pan Type:SELECT PAN---------------Straight Pan, cover-to-cover centerline width of __ inches and __ inches longTapered Pan, cover-to-cover centerline width of __ inches and __ inches long

Roman Tile

F. Spanish Roof Tile Type __:

Acceptable Product:SELECT PRODUCT---------------13-1/4 inch Spanish Tile18-3/8 inch Spanish Tile

G. Tower Clay Roof Tile Type __:

Acceptable Product: Tower Tile System

H. Special Shapes & Fittings:

Hip Caps Ridge Caps Rake Edges Detached Gable Rake Edges Eave Edges Valley Edges Termination Caps Half tile End Bands

CERAMIC ROOF TILE

A. Interlocking Ceramic Roof Tile Type __:

Ceramic Roof Tiles: Ceramic Slate

Color:SELECT COLOR---------------Slate GrayMontpelier GreenBrunswick BlackSlate RedPlumstoneAs selected by Architect from mfg's standard colorsColor Blend: Slate Gray: ____ percentColor Blend: Montpelier Green: ____ percentColor Blend: Brunswick Black: ____ percentColor Blend: Slate Red: ____ percentColor Blend: Plumstone: ____ percent

B. Special Shapes & Fittings:

Hip Caps Ridge Caps Rake Edges Detached Gable Rake Edges Eave Edges Valley Edges Termination Caps

ACCESSORY MATERIALS

NOTE: Do NOT select underlayment if specifying waterproofing membrane.

A. Underlayment:SELECT UNDERLAYMENT---------------Asphalt-impregnated fiberglass-reinforced organic feltAsphalt-saturated organic felt conforming to ASTM D 226, Type II, non-perforated,Asphalt-saturated & coated organic felt conforming to ASTM D 2626, non-perforated

B. Waterproofing Membrane

Ice Dam Protection: (For tile installation subjected to sever weather conditions)

C. Flashing:SELECT FLASHING------------------Terne coated stainless steel; 0.015 inch (0.38 mm) thick stainless steel core materialASTM B 370 copper, cold rolled, 16 oz/sq ft (0.56 mm thick), natural finishLead sheet, 2.5 lb/sq ft (1 mm thick); complying with ASTM B 749

D. Copper Wire: 18 gage (1.2 mm) minimum

E. Roof Cement: Asphalt roof cement conforming to ASTM D 4586, Type I or II

NOTE: Do not select if waterproofing membrane is specified, specify joint sealer instead

FLASHING FABRICATION

Choose 1 of the following: If specifying sheet metal items, edit 1st paragraph, if specified elsewhere edit the 2nd

Fabricate other indicated sheet metal items as follows:

1. Gutters: SMACNA Plate Number_______

2. Conductor Heads: SMACNA Plate Number_______

3. Downspouts: SMACNA Plate Number_______

Fabricate of other indicated sheet metal is specified in Section 07600

2. When you are finished making selections:

Generate Spec: Word     WP   or   RTF