| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| 1. Configure Solatube International TUBULAR DAYLIGHTING DEVICE: |
| TUBULAR DAYLIGHTING DEVICES |
 |  | SolaMaster Series: Solatube Model 750 DS-O Open Ceiling, 21 inch (530 mm) Daylighting System: |
 |  | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | Roof Dome Assembly: |
| | | Outer Dome Glazing: Type DA, 0.125 inch (3.2 mm) minimum thickness injection molded acrylic classified as CC2 material; UV inhibiting (100 percent UV C, 100 percent UV B and 98.5 percent UV C), impact modified acrylic blend. |
| | | Inner Dome Glazing: |
| | | | | Security Kit: Type SK Dome Security Kit, rivets with nylon spacers to replace dome screws. |
| | Roof Flashing Base: |
| | | | One piece, seamless, leak-proof flashing functioning as base support for dome and top of tube. Sheet steel, corrosion resistant conforming to ASTM A 653/A 653M or ASTM A 463/A 463M, 0.028 inch (0.7 mm) thick. |
| | NOTE: 8 inch or 11 inch bases are recommended for flat commercial roofs. Curb cap is normally used only on metal roofs or other roofs where curb is preferred. |
| | | | Roof Flashing Base Style: |
| | | | Two-piece, inverted flange Metal Roof Flashing for Standing Seam Rib roof profile with greater than 14-3/8 inch (365 mm) minimum distance between ribs permitting a required greater than 2 inch (51 mm) clearance between flashing and rib: Type FSM. Aluminum 1060 Alloy, corrosion resistant conforming to ASTM B 209, 0.059 inch (1.5 mm) thick. |
| | | Flashing Insulator: Type FI, Thermal isolation material for use under flashing. |
| | | Dome Edge Protection Band: Type PB, For fire rated roofs with turret height less than 8 inches (203 mm). Galvanized steel. Nominal thickness of 0.039 inch (1 mm). |
| | | Roof Flashing Turret Extensions: |
| | | Reflective Tubes: (Tubing *Not* Standard. No Tubing Supplied Unless Selected) |
| | | | Top Tube Angle Adapter, Type TA: Reflective 45 degree adjustable Top Tube Angle Adapter, 16 inches (406 mm) long. |
| | | | Bottom Tube Angle Adapter, Type BA: Reflective 45 degree adjustable Bottom Tube Angle Adapter, 16 inches (406 mm) long. |
| | | | Top Tube Angle Adapter and Bottom Tube Angle Adapter Kit, Type AK: Reflective 45 degree adjustable top and bottom angle adapters (one each), 16 inches (406 mm) long. |
| | | | Extension Tube: Reflective extension tube, Type EXX, 24 inches (610 mm) long. |
| | | | Reflective 90 degree Adjustable tube: |
| | | | | Type A1 one 0 to 90 degree extension tube angle adapter |
| | | | | Type A2 two 0 to 90 degree extension tube angle adapters |
| | Diffuser Lens: |
| | Accessories: |
| | | | Security Bar: Type B Security Bar 0.375 inch (95 mm) stainless steel bar across flashing diameter opening. |
| | | | Open ceiling trim ring: Type R, ABS Plastic, White; nominal thickness of 0.04 inch (1mm). |
| | | | Wire Suspension Kit: Type E, Use the wire suspension kit when additional bracing to the structure is required. |
| | | | Local Dimmer Control: Type D |
|
 |  | SolaMaster Series: Solatube Model 750 DS-C Penetrating Ceiling, 21 inch (530 mm) Daylighting System: |
 |  | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | Roof Dome Assembly: |
| | | Outer Dome Glazing: Type DA, 0.125 inch (3.2 mm) minimum thickness injection molded acrylic classified as CC2 material; UV inhibiting (100 percent UV C, 100 percent UV B and 98.5 percent UV C), impact modified acrylic blend. |
| | | Inner Dome Glazing: |
| | | | | Security Kit: Type SK Dome Security Kit, rivets with nylon spacers to replace dome screws. |
| | Roof Flashing Base: |
| | | | One piece, seamless, leak-proof flashing functioning as base support for dome and top of tube. Sheet steel, corrosion resistant conforming to ASTM A 653/A 653M or ASTM A 463/A 463M, 0.028 inch (0.7 mm) thick. |
| | NOTE: 8 inch or 11 inch bases are recommended for flat commercial roofs. Curb cap is normally used only on metal roofs or other roofs where curb is preferred. |
| | | | Roof Flashing Base Style: |
| | | | Two-piece, inverted flange Metal Roof Flashing for Standing Seam Rib roof profile with greater than 14-3/8 inch (365 mm) minimum distance between ribs permitting a required greater than 2 inch (51 mm) clearance between flashing and rib: Type FSM. Aluminum 1060 Alloy, corrosion resistant conforming to ASTM B 209, 0.059 inch (1.5 mm) thick. |
| | | Flashing Insulator: Type FI, Thermal isolation material for use under flashing. |
| | | Dome Edge Protection Band: Type PB, For fire rated roofs with turret height less than 8 inches (203 mm). Galvanized steel. Nominal thickness of 0.039 inch (1 mm). |
| | | Roof Flashing Turret Extensions: |
| | | Reflective Tubes: (Tubing *Not* Standard. No Tubing Supplied Unless Selected) |
| | | | Top Tube Angle Adapter, Type TA: Reflective 45 degree adjustable Top Tube Angle Adapter, 16 inches (406 mm) long. |
| | | | Bottom Tube Angle Adapter, Type BA: Reflective 45 degree adjustable Bottom Tube Angle Adapter, 16 inches (406 mm) long, required for transition box. |
| | | | Top Tube Angle Adapter and Bottom Tube Angle Adapter Kit, Type AK: Reflective 45 degree adjustable top and bottom angle adapters (one each), 16 inches (406 mm) long. |
| | | | Extension Tube: Reflective extension tube, Type EXX, 24 inches (610 mm) long. |
| | | | Reflective 90 degree Adjustable tube: |
| | | | | Type A1 one 0 to 90 degree extension tube angle adapter |
| | | | | Type A2 two 0 to 90 degree extension tube angle adapters |
| | Diffuser Lens: |
| | | Note: Required to meet Florida Building Code High Velocity Wind Zone and Texas Department of Insurance Impact Resistant zone requirements. |
| | | | Supplemental Natural Effect Lens made of acrylic for energy star rating. Type LN |
| | Accessories: |
| | | | Security Bar: Type B Security Bar 0.375 inch (95 mm) stainless steel bar across flashing diameter opening. |
| | | | Wire Suspension Kit: Type E, Use the wire suspension kit when additional bracing to the structure is required. |
| | | | Local Dimmer Control: Type D |
|
 |  | SolaMaster Series: Solatube Model 330 DS-O Open Ceiling, 21 inch (530 mm) Daylighting System: |
 |  | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | Roof Dome Assembly: |
| | | Glazing: Type DA, 0.143 inch (3.7 mm) minimum thickness injection molded acrylic classified as CC2 material; UV inhibiting (100 percent UV C, 100 percent UV B and 98.5 percent UV C), impact modified acrylic blend. |
| | Roof Flashing Base: |
| | | | One piece, seamless, leak-proof flashing functioning as base support for dome and top of tube. Sheet steel, corrosion resistant conforming to ASTM A 653/A 653M or ASTM A 463/A 463M, 0.028 inch (0.7 mm) thick. |
| | NOTE: 8 inch or 11 inch bases are recommended for flat commercial roofs. Curb cap is normally used only on metal roofs or other roofs where curb is preferred. |
| | | | Roof Flashing Base Style: |
| | | | Two-piece, inverted flange Metal Roof Flashing for Standing Seam Rib roof profile with greater than 14-3/8 inch (365 mm) minimum distance between ribs permitting a required greater than 2 inch (51 mm) clearance between flashing and rib: Type FSM. Aluminum 1060 Alloy, corrosion resistant conforming to ASTM B 209, 0.059 inch (1.5 mm) thick. |
| | | Flashing Insulator: Type FI, Thermal isolation material for use under flashing. |
| | | Dome Edge Protection Band: Type PB, For fire rated roofs with turret height less than 8 inches (203 mm). Galvanized steel. Nominal thickness of 0.039 inch (1 mm). |
| | | Roof Flashing Turret Extensions: |
| | | Reflective Tubes: (Tubing *Not* Standard. No Tubing Supplied Unless Selected) |
| | | | Top Tube Angle Adapter, Type TA: Reflective 45 degree adjustable Top Tube Angle Adapter, 16 inches (406 mm) long |
| | | | Bottom Tube Angle Adapter, Type BA: Reflective 45 degree adjustable Bottom Tube Angle Adapter, 16 inches (406 mm) long. |
| | | | Top Tube Angle Adapter and Bottom Top Tube Angle Adapter Kit, Type AK: Reflective 45 degree adjustable top and bottom angle adapters (one each), 16 inches (406 mm) long. |
| | | | Extension Tube: Reflective extension tube, Type EXX, Notched for Open Ceiling diffuser attachment, 24 inches (610 mm) long. |
| | | | Reflective 90 degree Adjustable tube: |
| | | | | Type A1 one 0 to 90 degree extension tube angle adapter |
| | | | | Type A2 two 0 to 90 degree extension tube angle adapters |
| | Diffuser Lens: |
| | | Secondary Diffuser: Type SS, Acrylic plastic classified as CC2 material. |
| | Accessories: |
| | | | Security Bar: Type B Security Bar 0.375 inch (95 mm) stainless steel bar across flashing diameter opening. |
| | | | Security Kit: Type SK Dome Security Kit, rivets with nylon spacers to replace dome screws. |
| | | | Open Ceiling Trim Ring: Type R, ABS Plastic, White; nominal thickness of 0.04 inch (1mm). |
| | | | Wire Suspension Kit: Type E, Use the wire suspension kit when additional bracing to the structure is required. |
| | | | Local Dimmer Control: Type D |
|
 |  | SolaMaster Series: Solatube Model 330 DS-C Penetrating Ceiling, 21 inch (530 mm) Daylighting System: |
 |  | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | Roof Dome Assembly: |
| | | Glazing: Type DA, 0.143 inch (3.7 mm) minimum thickness injection molded acrylic classified as CC2 material; UV inhibiting (100 percent UV C, 100 percent UV B and 98.5 percent UV C), impact modified acrylic blend. |
| | Roof Flashing Base: |
| | | | One piece, seamless, leak-proof flashing functioning as base support for dome and top of tube. Sheet steel, corrosion resistant conforming to ASTM A 653/A 653M or ASTM A 463/A 463M, 0.028 inch (0.7 mm) thick. |
| | NOTE: 8 inch or 11 inch bases are recommended for flat commercial roofs. Curb cap is normally used only on metal roofs or other roofs where curb is preferred. |
| | | | Roof Flashing Base Style: |
| | | | Two-piece, inverted flange Metal Roof Flashing for Standing Seam Rib roof profile with greater than 14-3/8 inch (365 mm) minimum distance between ribs permitting a required greater than 2 inch (51 mm) clearance between flashing and rib: Type FSM. Aluminum 1060 Alloy, corrosion resistant conforming to ASTM B 209, 0.059 inch (1.5 mm) thick. |
| | | Flashing Insulator: Type FI, Thermal isolation material for use under flashing. |
| | | Dome Edge Protection Band: Type PB, For fire rated roofs with turret height less than 8 inches (203 mm). Galvanized steel. Nominal thickness of 0.039 inch (1 mm). |
| | | Roof Flashing Turret Extensions: |
| | | Reflective Tubes: (Tubing *Not* Standard. No Tubing Supplied Unless Selected) |
| | | | Top Tube Angle Adapter, Type TA: Reflective 45 degree adjustable Top Tube Angle Adapter, 16 inches (406 mm) long |
| | | | Bottom Tube Angle Adapter, Type BA: Reflective 45 degree adjustable Bottom Tube Angle Adapter, 16 inches (406 mm) long, required for transition box. |
| | | | Top Tube Angle Adapter and Bottom Top Tube Angle Adapter Kit, Type AK: Reflective 45 degree adjustable top and bottom angle adapters (one each), 16 inches (406 mm) long. |
| | | | Extension Tube: Reflective extension tube, Type EXX, 24 inches (610 mm) long. |
| | | | Reflective 90 degree Adjustable tube: |
| | | | | Type A1 one 0 to 90 degree extension tube angle adapter |
| | | | | Type A2 two 0 to 90 degree extension tube angle adapters |
| | Diffuser Lens: |
| | | | Supplemental Natural Effect Lens made of acrylic for energy star rating. Type LN |
| | | Secondary Diffuser: Type SS, Acrylic plastic classified as CC2 material. |
| | Accessories: |
| | | | Security Bar: Type B Security Bar 0.375 inch (95 mm) stainless steel bar across flashing diameter opening. |
| | | | Security Kit: Type SK Dome Security Kit, rivets with nylon spacers to replace dome screws. |
| | | | Wire Suspension Kit: Type E, Use the wire suspension kit when additional bracing to the structure is required. |
| | | | Local Dimmer Control: Type D |
|
 |  | Brighten Up Series: Solatube Model 290 DS: 14 Inch (350 mm) Daylighting System: |
 |  | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | Roof Dome Assembly: |
| | | Outer Dome Glazing: Type DA, 0.125 inch (3.25 mm) minimum thickness impact resistant injection molded acrylic classified as CC2 material; UV inhibiting inhibiting (100 percent UV C, 100 percent UV B and 98.5 percent UV C), impact modified acrylic blend. |
| | | Shock Inner Dome Glazing: Type DI, 0.115 inch (2.9 mm) minimum thickness classified as CC1 material. High impact resistant injection molded acrylic (Hurricane Zones Only) |
| | NOTE: Steel bases are available both flat and pitched. |
| | NOTE: For different roof slope use base that is closest fit but be aware that skylight dome will not be mounted precisely level. |
| | Flashing Base: |
| | | Flashing Insulator: Type FI, Thermal isolation material for use under flashing |
| | | Metal Roof Flashing Kit: Type MR. Includes Butyl tape, flashing screws, speed nuts, corner washers and polyurethane sealant |
| | | Dome Edge Protection Band: Type PB, For fire rated roofs. Aluminized steel. Nominal thickness of 0.028 inches (0.7 mm) |
| | | Roof Flashing Turret Extensions: |
| | | Reflective extension tube, Type EXX, 24 inches (610 mm) long. |
| | | Reflective 90 degree Adjustable tube |
| | | | Type A1 one 0 to 90 degree extension tube angle adapter |
| | | | Type A2 two 0 to 90 degree extension tube angle adapters |
| | Dual Glazed Diffuser Assembly: |
| | Accessories: |
| | | | Lighting Fixture for 290 DS: |
| | | | Local Dimmer Control: Type D |
| | | | Wire Suspension Kit: Type E |
|
 |  | Brighten Up Series: Solatube Model 160 DS: 10 Inch (250 mm) Daylighting System: |
 |  | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | Roof Dome Assembly: |
| | | Outer Dome Glazing: Type DA, 0.125 inch (3 mm) minimum thickness injection molded acrylic classified as CC2 material; UV inhibiting (100 percent UV C, 100 percent UV B and 98.5 percent UV C), impact modified acrylic blend. |
| | | Shock Inner Dome Glazing: Type DI, 0.115 inch (2.9 mm) minimum thickness classified as CC1 material. High impact injection molded acrylic required for high velocity wind zones(Hurrican Zones Only) |
| | Note: Steel bases are available both flat and pitched. |
| | Note: For different roof slope use base that is closest fit but be aware that skylight dome will not be mounted precisely level. |
| | Flashing Base: |
| | | Flashing Insulator: Type FI, Thermal isolation material for use under flashing |
| | | Metal Roof Flashing Kit: Type MR. Includes Butyl tape, flashing screws, speed nuts, corner washers and polyurethane sealant |
| | | Dome Edge Protection Band: Type PB, For fire rated roofs. Aluminized steel. Nominal thickness of 0.028 inches (0.7 mm) |
| | | Roof Flashing Turret Extensions: |
| | | Reflective extension tube, Type EXX, 24 inches (610 mm) long. |
| | | Reflective 90 degree Adjustable tube |
| | | | Type A1 one 0 to 90 degree extension tube angle adapter |
| | | | Type A2 two 0 to 90 degree extension tube angle adapters |
| | Dual Glazed Diffuser Assembly: |
| | Accessories: |
| | | | Lighting Fixture for 160 DS: |
| | | | Local Dimmer Control: Type D |
| | | | Wire Suspension Kit: Type E |
| | | | Exhaust Fan: Type VEN |
| | | | | Exhaust Vent, Low Profile Roof Cap, Type RV |
| | | | Electrical Requirements: |
|
| 2. When you are finished making selections: |
 | Generate Spec: Word WP or RTF |