Planicrete AC is a one-component, concentrated liquid latex admixture used to enhance the performance of cementitious repair mortars, plasters, stuccos, concrete mixes and toppings for the restoration of horizontal, vertical and overhead concrete; concrete masonry units (CMU); and masonry surfaces.

ECO Prim Grip is a ready-to-use, low-VOC, synthetic resin-based primer with bond-promoting silica aggregates suspended in a dispersion. It enhances the performance and adhesion of mortars to existing ceramics and difficult-to-bond substrates, plus it improves bonding of self-leveling underlayments (SLUs) and bonds of render coats over cementitious substrates. Suitable for a wide variety of substrates, ECO Prim Grip combines excellent versatility with an easy, low-odor application.

2-1/2 to 1 is a grouting compound for interior or exterior floors of terra-cotta tile, such as Brazilian and Spanish tile, where grout joints range from 3/8" to 3/4" (10 to 19 mm).

Keracolor S is a premium-grade, preblended, polymer-modified sanded Portland-cement tile grout that requires only the addition of water for mixing. It will grout joints from 1/8" to 5/8" (3 to 16 mm).

Keracolor U is a premium-grade, preblended, polymer-modified unsanded Portland-cement tile grout that requires only the addition of water for mixing. It will grout joints from 1/16" to 1/8" (1,5 to 3 mm).

Ultracolor Plus with DropEffect™ technology is an ultra premium, fast-setting, polymer-modified, color-consistent, nonshrinking, efflorescence-free grout for joint widths from 1/16" to 1" (1,5 mm to 2,5 cm). DropEffect technology reduces surface absorption to help repel water, dirt and grime from penetrating grout joints. Ultracolor Plus is specially formulated with MAPEI's High-Hydrated Cement Technology (HCT') to eliminate the common problems related to Portland-cement grout, such as color consistency and efflorescence.

Mapesonic 2 is a patent-pending, next-generation, flexible thin, 76-mil (1,93-mm) lightweight, load-bearing, fabric-reinforced "peel-and-stick" sound-reduction and crack-isolation membrane. After application, ceramic tile or stone can be installed immediately with recommended MAPEI polymer-modified cement-based mortar, or glue-down wood flooring can be immediately installed with any MAPEI urethane or hybrid-polymer-based wood adhesive. Mapesonic 2 reduces transmission of impact sound (footsteps, dropped objects, etc.) and airborne sound (voice, TV, etc.) through floors when installed under ceramic tile, stone or wood floor coverings. It also helps to prevent existing or future in-plane floor cracks (with movement up to 3/8" (10 mm) wide) from transmitting through grout, ceramic tile or natural-stone assemblies.

Mapeguard 2 is a next-generation, flexible thin, 40-mil lightweight, load-bearing, fabric-reinforced "peel-and-stick" crack-isolation membrane. After application, ceramic tile or stone can be installed immediately with any polymer-modified cement-based mortar. Glue-down wood flooring can also be installed with any MAPEI urethane adhesive.

MAPEI SM Primer is a ready-to-use, fast-drying, water-based, latex primer for use under MAPEI's peel-and-stick sheet membranes on residential and commercial indoor or outdoor floors. MAPEI SM Primer greatly increases the bond of MAPEI's peel-and-stick sheet membranes to concrete, plywood and other approved, properly prepared floors. It can be applied with a roller or brush, is white in color and dries clear.

Mapelastic CI is a premixed, liquid-rubber, quick-drying crack-isolation membrane for installation under ceramic tile or stone in residential and commercial interior and exterior environments. Mapelastic CI meets ANSI A118.12 requirements, provides up to 1/8" (3 mm) of in-plane crack isolation, and dries after about 30 to 50 minutes. It is then ready to receive most MAPEI polymer-modified or epoxy mortars.

Keralastic is a premium-grade, high-performance, second-generation "flexible" acrylic latex additive used in the Kerabond/Keralastic™ System. This highly recommended additive enhances bond strength, flexural strength, elongation and freeze/thaw durability. To ensure proper flexibility, always use a latex additive when using a dry-set mortar for applications over plywood and for setting nonvitreous, semivitreous, vitreous and impervious tiles.

Keraply™ is a professional-grade, acrylic latex admixture used to enhance the performance of Keraset , Adesilex™ P10 and Keraflor™ dry-set mortars. This highly recommended admixture enhances bond strength, flexural strength, elongation and freeze/thaw durability. To ensure proper flexibility, always use a latex additive when using a dry-set mortar for applications over plywood and for setting nonvitreous tiles.

Floor & Wall Tile Mortar is a regular-setting, dry-set (non-polymer-enriched or "unmodified") mortar for installing tile on floors and walls in thin-set applications.

Floor Tile Mortar is a dry-set (non-polymer-enriched or "unmodified") mortar for installing floor tile in thin-set applications.

Kerabond is a premium-grade dry-set mortar for use in most interior, exterior, residential and light commercial floor and wall applications. This premium dry-set mortar is part of the Kerabond/Keralastic' high-performance mortar system.

Keraset is a dry-set mortar for use in interior/exterior residential and light commercial floor and wall applications.

Kerapoxy IEG CQ is a water-cleanable, 100%-solids epoxy grout with high chemical and stain resistance. It is a nonshrinking, nonsagging, fast-curing, efflorescence-free grout. Color-coated quartz dramatically improves its cleanability, so that Kerapoxy IEG CQ leaves very little film residue during cleanup of excess grout with a grout float. The color-coated quartz also eliminates pigment bleed, so tiles are not stained during installation.

Kerapoxy is a premium-grade, water-cleanable, 100%-solids, high-strength epoxy mortar and chemical-resistant nonsagging grout. Available in all MAPEI colors for grouting, Kerapoxy is excellent for countertops, high-traffic areas, and areas needing stain and chemical resistance.

Kerapoxy CQ is an improved two-component, 100%-solids epoxy grout and mortar. Nonsagging/nonslumping in joints up to 3/8" (10 mm), water-cleanable and easy to apply, Kerapoxy CQ uses a proprietary aggregate to achieve its durable color, making it excellent for countertops, high-traffic areas, and areas needing stain and chemical resistance. Easy to maintain, Kerapoxy CQ will clean to the original color and contains BioBlock' technology to help protect against mold and mildew. Kerapoxy CQ is efflorescence-free and has excellent resistance to chemicals, staining, alkalinity, chlorine, bacteria, cracking and color deterioration. Because Kerapoxy CQ is impervious, this ensures that spills stay at the surface level for easier maintenance.

Granirapid is the next generation of high-performance, flexible mortar systems. As the industry's first and only fast-curing system geared for fast-track projects, it develops high, early mechanical strength and can be specified for the same demanding applications as Keralastic'. However, Granirapid will cure considerable faster because of its superior drying-out characteristics, which produce low residual moisture behind the tile after 24 hours, and does not contribute to efflorescence. When installed in conjunction with Ultracolor® Plus grout, Granirapid will allow water submersion in a revolutionary 72 hours.

Kerabond/Keralastic System is a high-performance, two-part system: Keralastic ', a second-generation "flexible" acrylic latex additive, is used to enhance the performance of Kerabond ', which is a premium-grade dry-set mortar. This system has exceptional bond strength, flexural strength, elongation and freeze/thaw durability. To ensure proper flexibility, always use a latex additive when applying a dry-set mortar over plywood or to set nonvitreous tiles.

Large Floor Tile Mortar is a regular-setting, polymer-enriched ("modified") mortar ideal for installing large-format tile on floors. This medium-bed mortar is designed to bond and support large tile over a diverse range of floor substrates.

Ultracontact is an ultra premium, normal-setting, polymer-modified, high-performance full-contact mortar. Ultracontact meets or exceeds ANSI A118.4 and ANSI A118.11 requirements when mixed with water.

Ultracontact RS is an ultra premium, rapid-setting, polymer-modified, high-performance full-contact mortar. It uses MAPEI's High-Hydrated Cement Technology (HCT™).

Keracrete is a specially formulated latex additive for use in job-site-prepared setting beds (1 part sand to 1 part cement), resulting in a highly water- and frost-resistant mortar. Keracrete can be used in interior and exterior applications over structurally sound concrete, masonry block, gypsum wallboard and cement board to set marble, granite, pavers, quarry tiles, and vitreous and nonvitreous ceramic tiles.

Ultralite Mortar is a premium-grade, lightweight, single-component thin-set mortar that can also be used for medium-bed and non-sag applications. This high-performance, polymer-modified mortar is formulated with Easy Glide Technology™ for ease of application, and with BioBlock™ technology for mold and mildew resistance. Ultralite Mortar 's unique Ultralite Technology' provides twice the coverage of a standard thin-set mortar and contributes to LEED points with over 20% recycled content.routs.

KerTM 909 is a ready-to-use, nonflammable, high-viscosity, synthetic polymer emulsion-based adhesive.

Type 1 is a professional-grade, traditional, nonflammable, organic adhesive for setting impervious, vitreous, semivitreous and nonvitreous tile over gypsum drywall (walls only), cement board, exterior-grade plywood, concrete and masonry block. This adhesive is used for interior applications only. Type 1 meets or exceeds ANSI A136.1, Type 1 requirements.

Grout Maximizer is a premium latex-based additive for mixing with Keracolor™ S Portland-cement-based grout to increase resistance to water and oil-based stains.

UltraCare Grout Refresh is a nonflammable, ready-to-use, water-based, polymermodified colorant and sealer for grout joints. It can be applied onto and bonds to cement, epoxy, urethane and acrylic grouts.

Keracaulk S is a premium-grade, easy-to-use, easy-to-clean siliconized acrylic caulk formulated to match the color and texture of MAPEI sanded grouts.

Keracaulk U is a premium-grade, easy-to-use, easy-to-clean siliconized acrylic caulk formulated to match the color and texture of MAPEI unsanded grouts.

Planiseal Easy is a proprietary MAPEI acrylic polymer specifically designed to treat concrete slabs (at least 14 days old) that exhibit moisture vapor emission rates (MVERs) up to 8 lbs. per 1,000 sq. ft. (3,63 kg per 92,9 m 2 ) per 24 hours (ASTM F1869) or up to 90% relative humidity (ASTM F 2170) and reduces transmission rates to 3 lbs. (1,36 kg) or less. Tinted green, Planiseal Easy is easy to apply with a 1/4" (6 mm) nap roller. This FastTrack Ready™ product dries quickly, allowing for floor-covering installations within 2 to 3 hours.

4 to 1 is a preblended mixture of finely graded sand and Portland cement used for thick-bed mortar installations. 4 to 1 flattens and levels an existing substrate before the installation of tile and stone.

Mapecem is a high-performance, shrinkage-compensated binder that is added to select aggregates with water to create a fast-curing, high-strength interior repair mortar and topping. Aggregate must be added to this product before placement. See the Mapecem Technical Data Sheet for aggregate mixing ratios and application thickness.

Mapecem ® Premix is a fast-setting, premixed cement-based mortar for concrete repairs and subfloor preparation work. Mixed exclusively with water, Mapecem Premix provides an easy-to-use, high-compressive-strength, fast-setting mortar that sets completely within 24 hours without shrinkage cracks. When properly used, Mapecem Premix will allow installation of ceramic tile and natural-stone flooring after only 3 to 4 hours and installation of floor covering (such as vinyl, wood, rubber, linoleum and carpet) after 16 to 18 hours.

Mapelath is a lightweight, noncorroding and alkali-resistant lath used to replace wire lath and traditional underlayments that are heavier, thicker and more labor-intensive to install. Mapelath minimizes the overall finished height of the floor.

Topcem Premix is a ready-to-use mortar requiring only the addition of water. Topcem Premix is suitable in both bonded and unbonded, interior and exterior applications. Topcem Premix has an accelerated cure, allowing for installation of ceramic flooring in 24 hours after placement, and nonbreathable flooring systems in 48 hours. Topcem Premix can easily be screeded or sloped, and has the workability and working time of conventional mortars with a much faster curing time. It is ideal for filling trenches, re-sloping balconies, or forming screeds that may or may not receive subsequent flooring installations.

Mapecem Quickpatch is a versatile, fast-setting, cementitious material used for the patching of interior/exterior concrete surfaces including concrete floors, driveways, sidewalks and concrete pads. Mapecem Quickpatch features extraordinary ease of placement, with a variable water ratio and outstanding workability. Light gray Mapecem Quickpatch can be applied from featheredge to 3" (7,5 cm) for ramping or filling. That makes it ideal for restoring weathered, damaged concrete surfaces to a uniform, superior wearing and better-than-new appearance. When used for horizontal substrate repair before application of self-leveling underlayments, Mapecem Quickpatch sets fast for easy and cost-efficient repairs, minimizing job-site turnaround time.

Planipatch Plus™ is an acrylic latex additive for use with Planipatch.

Planipatch is an ultra fast-drying, self-curing, polymer-modified, cement-based patching compound that rapidly develops high compressive strength. Use for smoothing, patching and filling cracks, holes, voids and depressions in concrete and approved wood underlayments prior to the installation of floor coverings. Floor coverings can be installed just 1 hour after application. Mix with Planipatch Plus' to use as an embossing leveler or patch over properly prepared vinyl sheet goods, vinyl composition tile (VCT), cement terrazzo and residual cutback adhesive surfaces.

Adesilex™ P10 is a premium-grade, bright white, multipurpose thin-set mortar formulated with nonsag properties. Adesilex P10 is designed for glass tile, glass mosaic and marble mosaic, and is ideal for light translucent natural stone.

Adesilex™ P10 is a premium-grade, bright white, multipurpose thin-set mortar formulated with nonsag properties. Adesilex P10 is designed for glass tile, glass mosaic and marble mosaic, and is ideal for light translucent natural stone.

Ceramic Tile Mortar is a regular-setting, polymer-enriched ("modified") mortar for installing tile and stone on floors and walls in thin-set applications.

Ker 111 is a single-component, thin-set mortar for interior and exterior installations of dimensional stone, ceramic, porcelain and quarry tile. This mortar is formulated with a unique dry polymer, resulting in good adhesion to substrates and tile.

Large Tile & Stone Mortar is a premium, regular-setting, polymer-enriched ("modified") medium-bed mortar ideal for installing large-format tile and stone on floors, walls and countertops. This mortar can also be used in thin-set applications to install smaller-format tile over a diverse range of substrates.

Mosaic & Glass Tile Mortar is regular-setting, polymer-enriched ("modified"), bright white, multipurpose mortar designed for installing sheet-mounted mosaic glass or stone tiles or individual tiles in thin-set applications.

Porcelain Tile Mortar is a regular-setting, polymer-enriched ("modified") mortar for installing a wide range of tile and stone over a diverse range of substrates in thin-set applications.

Rapid-Set Tile Mortar is a rapid-setting, polymer-enriched ("modified") mortar for installing a wide range of tile and stone over a diverse range of substrates in thin-set applications.

Ultraflex 1 is a standard-grade, single-component, polymer-modified thin-set mortar for most interior and exterior installations of tile. This mortar has an above average content of unique dry polymer, resulting in good adhesion to the substrate and tile. Ultraflex 1 can be used for both interior and exterior installations of tile in most residential floor and wall applications. In commercial applications, use on interior floor and wall installations and exterior floors. Ultraflex 1 meets or exceeds ANSI A118.4 and ANSI A118.11 requirements when mixed with water.

Ultraflex 2 is a professional-grade, single-component, high-performance, polymer-modified thin-set mortar for interior and exterior installations of tile. This mortar has a high content of unique dry polymer, resulting in excellent adhesion to the substrate and tile. Formulated with low-dust technology, Ultraflex 2 reduces dust by 90% during pouring and mixing, resulting in a cleaner environment. Ultraflex 2 meets or exceeds ANSI A118.4 and ANSI A118.11 requirements whenmixed with water.

Ultraflex 3 is a premium-grade, single-component, high-performance, polymer-modified thin-set mortar for interior and exterior installations of tile. This mortar has a high content of unique dry polymer, resulting in superior adhesion to the substrate and tile. In addition, it can be used for most interior/exterior residential and commercial tile applications on floors and walls. Ultraflex 3 meets or exceeds ANSI A118.4 and ANSI A118.11 when mixed with water.

Ultraflex™ Marble is a premium-grade, single-component, polymer-modified, rapid-setting mortar for moisture-sensitive marble and stone installations.

Ultraflex RS is a premium-grade, single-component, high-performance, polymer-modified, rapid-setting thin-set mortar for interior and exterior installations of tile. This mortar has a high content of unique dry polymer, resulting in excellent adhesion to the substrate and tile. Ultraflex RS is a FastTrack Ready' product, allowing grouting in 2 to 3 hours. It can be used for both interior and exterior installations of tile in most residential floor and wall applications. In commercial applications, use on interior floor and wall installations and exterior floors. Ultraflex RS meets or exceeds ANSI A118.4 and ANSI A118.11 requirements for fast-setting mortars when mixed with water.

Ultraflex LFT is a premium, nonsag medium-bed and thin-set mortar for large-format and heavy tile and stone for interior/exterior floor, wall and countertop installations. This mortar has a high content of unique dry polymer, resulting in excellent adhesion to the substrate and tile. It is formulated with Easy Glide Technology' for ease of application.

Ultraflex LFT Rapid is a premium, rapid-setting, nonsag medium-bed and thin-set mortar for large-format tile and stone for interior/exterior floor, wall and countertop installations. This mortar has a high content of unique dry polymer, resulting in excellent adhesion to the substrate and tile. Ultraflex LFT Rapid is FastTrack Ready™, allowing grouting in 3 to 4 hours.

Ultraflor is a medium-bed, polymer-modified mortar for interior and exterior setting of large-format tile, including heavy-ribbed-back tile, brick pavers, dimensional tile and natural-stone tile. Ultraflor is designed for use at 3/8" to 3/4" (10 to 19 mm) thickness to give better support under large-format tile.

Premixed Mortar is a premixed no-mess alternative to traditional thin-set mortars that require water and mixing. It is nonflammable and ready to use.

Natural-Stone & Marble Adhesive is a high-performance, nonflammable, acrylic latex adhesive for interior installations of marble, natural-stone, ceramic, and porcelain floor and wall tile. Its fast-grabbing, nonslip formula simplifies vertical installation of tiles.

Premium Mortar is a premixed no-mess alternative to traditional thin-set mortars that require water and mixing. It is nonflammable and ready to use.

Premixed Grout is a premixed stain-resistant grout for ceramic, porcelain and natural-stone tile in residential light-duty interior installations, such as walls, floors, countertops and showers.

Premixed Mortar is a premixed no-mess alternative to traditional thin-set mortars that require water and mixing. It is nonflammable and ready to use.

Premixed Patch & Level is a self-curing, polymer-modified, premixed patching compound that has a gray appearance.

Premixed Premium Grout is a premixed stain-resistant grout for ceramic, porcelain and natural-stone tile in residential light-duty interior installations, such as walls, floors, countertops and showers.

Premixed Thin-Set Mortar is a no-mess alternative to traditional thin-set mortars that require water and mixing. It is nonflammable and ready-mixed. Ready-to-use, no-mix thin-set mortar.

Primer E is a two-component, 100%-solids epoxy primer and bonding agent designed for use with MAPEI self-leveling underlayments and toppings. Primer E is the most effective method for bonding to nonporous, dense substrates before installing self-leveling underlayments or toppings subject to high stress. Primer E is highly recommended for all installations of decorative toppings (such as Ultratop ® ), which demand the highest degree of crack resistance and surface finish. Primer E low viscosity makes installation fast and easy, and provides excellent penetration into the substrate and therefore tenacious bond.

Primer L is a concentrated, solvent-free acrylic primer used before the installation of underlayments and topping materials. It is green for easy identification. Primer L improves the bond between a properly prepared and profiled concrete substrate, and self-leveling underlayment or topping materials.

Novoplan Easy Plus is an improved, high-strength, self-leveling, calcium-aluminate-based underlayment and repair mix for interior concrete and engineer-approved floors. Its unique formulation allows for direct application on substrates that are clean, securely bonded and properly primed.

Novoplan 2 Plus is a high-strength, self-leveling cement-based underlayment and repair mix with quicker curing time, for interior concrete and engineer-approved floors.

Planitex SL 35 is a gypsum-based, self-leveling underlayment with an exceptionally smooth, hard surface for use in dry interior residential and commercial areas. Planitex SL 35 is designed for application at depths of 1/4" to 3" (6 mm to 7,5 cm) and provides an excellent substrate for floor coverings such as rubber, sheet vinyl and vinyl composition tile (VCT). Planitex SL 35 can be used to cover radiant or in-floor heating systems. Its impressive compressive and flexural strengths allow it to support light wheeled traffic and light commercial activity.

Self-Leveler is a high-strength, regular-setting, cement-based, self-leveling underlayment and repair mix for use over interior concrete, plywood or other approved floor surfaces. Self-Leveler is convenient and easy to use. Once cured, it provides a smooth, level surface on which to install a variety of floor coverings.

Ultraplan Easy is an HCT™ (High-Hydrated Cement Technology)-based, quick-setting, self-leveling underlayment that typically requires only a clean, soundly bonded substrate before application. Typically requiring reduced surface preparation, Ultraplan Easy provides lower installation costs and fast turnaround on job sites. It features high strength and is able to withstand light foot traffic after 2 to 3 hours of installation.

Ultraplan 1 Plus is an HCT™ (High-Hydrated Cement Technology)-based, quick-setting, self-leveling, self-drying underlayment and repair mix for interior concrete and engineer-approved floors. Ultraplan 1 Plus has high strength and is abrasion-resistant, able to withstand light foot traffic after 2 to 3 hours and vehicular rubber-wheel traffic after 3 days.

Glass-Block Mortar is a premixed blend of Portland cement, sand and chemicals specifically designed for glass-block installation. This white mortar can be used for both setting and grouting of the block.

Kerapoxy 410 is a 100%-solids epoxy setting floor and wall mortar that is suited for areas where most chemical-resistant setting material is necessary. Kerapoxy 410 is formulated to be used as a non sag thin-set for wall applications of porcelain and monocottura tile up to 12" x 12" x 3/8" (30 cm x 30 cm x 10 mm) in format. It also has high compressive strength, which provides excellent impact strength in commercial facilities. Kerapoxy 410 is designed for setting most types of tile.

Planicrete W is tremendously flexible and excellent for installing tile over well-supported and properly prepared steel substrates (such as ship decks, elevators, steel staircases and bank vaults). It is designed for setting most types of tile, including moisture-sensitive tile and natural stone such as Rosso Levanto marble, Negro Marquina marble, and green marble and their agglomerates.

MAPEI's Fiberglass Mesh is a ready-to-use, thin, strong yet flexible alkali-resistant mesh for embedment with waterproofing and crack-isolation membranes, including MAPEI's Mapelastic, Mapelastic 315, Mapelastic HPG and Mapelastic Smart on residential and commercial floors, walls and ceilings.

Mapeband is a set of rubber-coated, polyester accessories for labor-saving installation of interior and exterior waterproofing. Sold separately, these accessories consist of a cove roll (tape), drain flashing and (available in Canada only) pre-formed inside and outside corners. Mapeband accessories are designed for use with MAPEI's Mapelastic™, Mapelastic 315 , Mapelastic HPG and Mapelastic Smart waterproofing membranes.

Mapelastic 315 is a trowel-applied, two-component, flexible, fiber-reinforced waterproofing and crack-isolation membrane. Mapelastic 315 meets ANSI A118.10 requirements for waterproofing and is IAPMO-listed as a shower-pan liner.

Mapelastic AquaDefense is a premixed, advanced liquid-rubber, extremely quick-drying waterproofing and crack-isolation membrane for installation under ceramic tile or stone in residential, commercial and industrial environments. Mapelastic AquaDefense provides a thin, continuous barrier to protect adjacent rooms and floors below from water damage. For common problem areas like coves, corners, cracks and drains, it can be combined with MAPEI's optional Reinforcing Fabric or Mapeband' accessories (cove roll and drain flash) to provide additional protection. Mapelastic AquaDefense dries after about 30 to 50 minutes and is then ready to receive any MAPEI polymer or epoxy mortar. Mapelastic AquaDefense can be flood-tested after 12 hours of drying time, is IAPMO-listed for use as a shower-pan liner, and exceeds ANSI A118.10 and ANSI A118.12 standards.

Mapelastic HPG is a next-generation, ready-to-use liquid membrane suited for concrete, masonry, cement board and engineer-approved, exterior-grade plywood. It is designed for both commercial and residential use. It can be applied to interior horizontal and vertical surfaces using a trowel or roller, and is a highly flexible acrylic-based membrane. Mapelastic HPG has excellent compatibility with cement-based bonding materials. It can accommodate minor in-plane substrate movement and also can be used as a crack-isolation membrane (when used with MAPEI™s Fiberglass Me sh ). When used with this mesh, Mapelastic HPG is IAPMO-approved and meets ANSI A118.10 standards for use as a shower-pan liner.

MAPEI's Reinforcing Fabric is a strong, absorbent polyester reinforcing fabric to use with Mapelastic 400 and for optional use with Mapelastic AquaDefense.

UltraCare Abrasive Surface Cleaner is a powerful, abrasive cleaner that is safe for use on a variety of ceramic, porcelain and natural-stone surfaces. This water-based, biodegradeable formula is nontoxic and nonflammable, containing no VOCs or acids. Cleaning does not require letting the product stand on the surface. UltraCare Abrasive Surface Cleaner penetrates deep into dense surface pores and easily removes ground-in dirt, grime, rust stains and mineral deposits. This product is formulated to remove most factory-applied waxes and floor finishes as well as light cementitious and epoxy grout residue. It is excellent for use on heavily textured and hard-to-clean surfaces. Plus, it can be used in combination with any UltraCare cleaner or problem-solver.

UltraCare Acidic Tile & Grout Cleaner is a highly concentrated acidic cleaner formulated to remove cement grout haze, mortar residue, mineral deposits, rust stains and efflorescence from tile, concrete and masonry surfaces. It is also effective for removing hard-water stains, lime deposits and soap scum. This product contains no phosphates.

UltraCare Concentrated Tile & Grout Cleaner is a highly concentrated neutral cleaner with a lemon scent for everyday use. When used regularly and per the directions, this biodegradable, neutral cleaner helps to maintain a variety of ceramic, porcelain and natural-stone surfaces as well as grout in pristine condition. In addition, it helps to prevent soap scum buildup and hard-water deposits.

UltraCare Everyday Stone & Grout Cleaner & Resealer is a ready-to-use, everyday spray cleaner. This product helps to boost the performance of any existing penetrating sealers while cleaning and deodorizing. Powerful enough to help dissolve grease and grime, UltraCare Everyday Stone & Grout Cleaner & Resealer is ideal for kitchen and bathroom countertops. Non-acidic, it is safe to use on natural stone, grout and tile.

UltraCare Everyday Stone Clean & Polish is a ready-to-use everyday spray cleaner and polish. This product will clean and help to enhance the appearance and beauty of natural stone all in one step. Ideal for kitchen and bathroom countertops, UltraCare Everyday Stone Clean & Polish is safe to use on natural stone

UltraCare Everyday Stone, Tile & Grout Cleaner is a high-performance, ready-to-use, everyday spray cleaner. This product helps to clean and deodorize kitchens and bathroom with a fresh lemon smell. Powerful enough to help dissolve grease and grime, UltraCare Everyday Stone, Tile & Grout Cleaner is ideal for kitchen and bathroom countertops. Non-acidic, it is safe to use on natural stone, grout and tile.

UltraCare Grout Refresh Pre-Cleaner is a ready-to-use cleaner specially formulated to prepare grout joints before application of MAPEI's UltraCare Grout Refresh. UltraCare Grout Refresh Pre-Cleaner will remove grease, dirt, soil, soap scum and hard water deposits from grout joints to ensure a superior bond for UltraCare Grout Refresh. This product should not be used on epoxy grout joints.

UltraCare Heavy-Duty Stone, Tile & Grout Cleaner is a highly concentrated and high-alkaline cleaner and degreaser. This product is formulated to quickly remove most waxes, grease, oil, light soap scum, and stains from mildew and algae. It is quite effective at removing most factory-applied waxes and floor finishes, and is ideal for areas that have been neglected or subject to heavy use.

UltraCare Cement Grout Haze Remover is a professional-strength formulation that helps to remove cement grout haze from tile, concrete and stone surfaces. It is an acidic, low-odor, non-flammable, easy-to-use, water-based formula.

UltraCare Deep Stain Remover for Stone helps to absorb food, grease and oil stains out of natural-stone surfaces including granite, marble, limestone, slate, travertine, terra cotta, flagstone, concrete and cementitious grout.

UltraCare Efflorescence Remover is a professional-strength, acid-based formulation that effectively removes efflorescence from ceramic and porcelain tile, concrete, brick and stone surfaces as well as cement grout.

UltraCare Epoxy Grout Haze Remover is a professional-strength formulation that helps to remove epoxy grout haze from tile, concrete and stone surfaces. UltraCare Epoxy Grout Haze Remover is water-based, has a natural citrus scent, is nonflammable and is easy to use.

UltraCare Heavy-Duty Sealer & Coating Stripper is a professional-strength formulation that helps to remove tough coatings, lacquers, varnishes, sealers, paints and epoxy grout haze from surfaces. This product effectively dissolves heavy wax, and helps to remove deep-set stains and heavy grease buildup. UltraCare Heavy-Duty Sealer & Coating Stripper is water-based, pleasantly scented, nonflammable and easy to use.

UltraCare Penetrating Plus SB Stone & Porcelain Tile Sealer is a premium, natural-look, solvent-based penetrating sealer that uses VOC-exempt materials and will provide maximum protection against most common stains for all interior and exterior natural stone (marble, limestone, sandstone, slate, granite, travertine, etc.), unglazed porcelain and ceramic tiles, masonry, quarry tiles and cement grout. The product can also be used as a pre-grouting sealer.

UltraCare Enhancing Plus Stone Sealer is a premium, color-enhancing penetrating sealer that enhances the natural colors of stone and provides maximum protection against most common stains. It is safe for use on all interior and exterior naturalstone surfaces, such as marble, limestone, sandstone, slate, granite, travertine and cementitious grout. The product can also be used as a pre-grouting sealer.

UltraCare Grout Sealer is an affordable, water-based penetrating sealer that will provide protection against most common stains for sanded and non-sanded cementitious grout joints. It can also be used as a pre-grouting sealer.

UltraCare Enhancing Stone Sealer is an economical, color-enhancing penetrating sealer that enhances the natural colors of stone and provides protection against most common stains. It is safe for use on all interior and exterior natural-stone surfaces such as marble, limestone, sandstone, slate, granite, travertine and cementitious grout. The product can also be used as a pre-grouting sealer.

UltraCare Penetrating Plus Stone, Tile & Grout Sealer is a premium, natural-look, water-based penetrating sealer that provides maximum protection against most common stains for all interior and exterior natural stone (marble, limestone, sandstone, slate, granite, travertine, etc.), unglazed ceramic tile, masonry and grout. The product can also be used as a pre-grouting sealer.

UltraCare Penetrating Stone, Tile & Grout Sealer is an economical, natural-look, water-based penetrating sealer that protects against most common stains for all interior and exterior natural stone (marble, limestone, sandstone, slate, granite, travertine, etc.), unglazed ceramic tile, masonry and cement grout. The product contains no silicones and can also be used as a pre-grouting sealer.

Primer CE is an ultra low-viscosity, two-component, 100%-solids surface-consolidating epoxy primer. Primer CE effectively penetrates and consolidates the surface of weak concrete or gypsum substrates. Applied in a single- coat application, Primer CE is designed to restore structural integrity to friable substrates such as weak gypsum-based underlayments or lightweight concretes before the application of underlayments, toppings or floor finishes. Once installed, Primer CE is compatible with a wide number of primers and adhesives typically used with flooring installations, such as with tile, vinyl composition tile (VCT), carpet, sheet vinyl, wood and other floor finishing products.

Primer E is a two-component, 100%-solids epoxy primer and bonding agent designed for use with MAPEI self-leveling underlayments and toppings. Primer E is the most effective method for bonding to nonporous, dense substrates before installing self-leveling underlayments or toppings subject to high stress. Primer E is highly recommended for all installations of decorative toppings (such as Ultratop ), which demand the highest degree of crack resistance and surface finish. Primer E low viscosity makes installation fast and easy, and provides excellent penetration into the substrate and therefore tenacious bond.

Primer L is a concentrated, solvent-free acrylic primer used before the installation of underlayments and topping materials. It is green for easy identification. Primer L improves the bond between a properly prepared and profiled concrete substrate, and self-leveling underlayment or topping materials.

Primer T is a low-VOC, water-based acrylic primer that enhances the performance and adhesion of self-leveling underlayments (SLUs) on nonabsorbent surfaces such as ceramic tile, vinyl composition tile (VCT) and adhesive residue, as well as profiled, absorbent surfaces. Suitable for a wide variety of substrates, Primer T combines excellent versatility with an easy, low-odor application.

Primer WE (formerly Ultraprime WE) is a two-component, polymer-modified, solvent-free water-based epoxy primer for enhanced adhesion to nonporous substrates prior to the application of MAPEI self-leveling materials. When mixed, Primer WE is purple for easy identification. It improves adhesion over smooth, nonabsorbent and difficult-to-bond-to substrates such as properly prepared ceramic tile, cement-based terrazzo, old cutback adhesive residue and approved plywood subfloors.

Novoplan 2 Plus is a high-strength, self-leveling cement-based underlayment and repair mix with quicker curing time, for interior concrete and engineer-approved floors.

Novoplan Easy Plus is an improved, high-strength, self-leveling, calcium-aluminate-based underlayment and repair mix for interior concrete and engineer-approved floors. Its unique formulation allows for direct application on substrates that are clean, securely bonded and properly primed.

Planitex SL 35 is a gypsum-based, self-leveling underlayment with an exceptionally smooth, hard surface for use in dry interior residential and commercial areas. Planitex SL 35 is designed for application at depths of 1/4" to 3" (6 mm to 7,5 cm) and provides an excellent substrate for floor coverings such as rubber, sheet vinyl and vinyl composition tile (VCT). Planitex SL 35 can be used to cover radiant or in-floor heating systems. Its impressive compressive and flexural strengths allow it to support light wheeled traffic and light commercial activity.

Self-Leveler is a high-strength, regular-setting, cement-based, self-leveling underlayment and repair mix for use over interior concrete, plywood or other approved floor surfaces. Self-Leveler is convenient and easy to use. Once cured, it provides a smooth, level surface on which to install a variety of floor coverings.

Ultraplan Easy is an HCT' (High-Hydrated Cement Technology)-based, quick-setting, self-leveling underlayment that typically requires only a clean, soundly bonded substrate before application. Typically requiring reduced surface preparation, Ultraplan Easy provides lower installation costs and fast turnaround on job sites. It features high strength and is able to withstand light foot traffic after 2 to 3 hours of installation.

Ultraplan 1 Plus is an HCT' (High-Hydrated Cement Technology)-based, quick-setting, self-leveling, self-drying underlayment and repair mix for interior concrete and engineer-approved floors. Ultraplan 1 Plus has high strength and is abrasion-resistant, able to withstand light foot traffic after 2 to 3 hours and vehicular rubber-wheel traffic after 3 days.

Ultraplan M20 Plus is an HCT™ (High-Hydrated Cement Technology) calcium-aluminate-based, quick-setting self-leveling, self-drying material. It is specially formulated for the resurfacing and construction of interior horizontal surfaces as a high-compressive-strength underlayment with maximum resistance to wheel tracking and indentations experienced in softer underlayments. Ultraplan M20 Plus is suitable for use as a commercial wear topping in warehouse and alternate industrial applications where an exceptional flat and smooth concrete surface is desired.

Mapecure SRA is a liquid admixture that reacts chemically to reduce hydraulic shrinkage and the formation of microcracks. Mapecure SRA is compatible with traditional MAPEI concrete restoration materials, such as cementitious grouts and repair mortars.

Planicrete AC is a one-component, concentrated liquid latex admixture used to enhance the performance of cementitious repair mortars, plasters, stuccos, concrete mixes and toppings for the restoration of horizontal, vertical and overhead concrete; concrete masonry units (CMUs); and masonry surfaces.

Planicrete UA is a next-generation, water-based, one-component, concentrated liquid latex admixture used to enhance the performance of several MAPEI products, including mortar mixes. Using Planicrete UA as part of the designated design mixes will increase product performance in the areas of bond, flexural and tensile strengths in addition to increased durability and enhanced workability.

Elastocolor Coat is a water-based, high-build, 100%-acrylic coating designed to protect and decorate above-grade, exterior/interior vertical concrete, masonry, stucco, fiber-reinforced polymer (FRP) composites and EIFS systems. Elastocolor Coat is available in two textures (smooth and fine), in a wide range of standard colors and in an unlimited number of custom colors to increase its design versatility

Elastocolor Flex is an elastomeric, high-build, water-based, 100%-acrylic coating to protect and decorate above-grade, vertical exterior concrete, masonry, stucco and EIFS systems. Elastocolor Flex is available in two textures (smooth and fine), in a wide range of standard colors and in an unlimited number of custom colors to increase its design versatility.

Elastocolor Paint is a high-quality, water-based, 100%-acrylic coating that forms a protective film for use on above-grade, exterior/interior concrete, masonry, stucco, fiber-reinforced polymer (FRP) composites and EIFS systems. Elastocolor Paint is available in a wide range of standard colors and in an unlimited number of custom colors to increase its design versatility.

Elastocolor Primer WB is a water-based, 100%-acrylic primer for use with Elastocolor coatings. Elastocolor Primer WB improves adhesion on porous, dusting and new substrates.

Mapecrete Protector FF is a film-forming, high-gloss protective coating designed to increase the stain resistance of interior concrete floors. Mapecrete Protector FF is ideal for polished or decorative concrete and cement terrazzo floors, and helps to protect against accidental spills of water and other staining materials (such as food products and household cleaners). Mapecrete Protector FF also increases the reflectivity (or gloss) of polished concrete floors.

Mapefinish Wet Look is a one-part, water-based, transparent, high-gloss sealer designed for protecting concrete surfaces - from highly textured stamped concrete to smooth self-leveling toppings. Mapefinish Wet Look utilizes a self-cross-linking acrylic resin that offers superior abrasion, blush resistance and slip resistance, outperforming most solvent-based acrylics and many urethane dispersions. Mapefinish Wet Look is low in VOCs, low-odor, non-yellowing and permeable to water vapor, making it perfect for application on both interior and exterior concrete surfaces. With its superior performance combined with user-friendly application, Mapefinish Wet Look is an ideal sealer for concrete and masonry.

Mapefloor Finish 415 NA is a two-component, solvent-free, aromatic polyurethane topcoat specifically designed to provide a protective wear coat for elevated concrete surfaces, where the Mapefloor parking deck system is utilized. Mapefloor Finish 415 NA, in combination with the proper Mapefloor parking deck system, protects concrete substrates from water and salt intrusion while, at the same time, providing a seamless, attractive, slip-resistant wearing surface.

Mapefloor Finish 450 is a two-component, solvent-free, aliphatic polyurethane topcoat specifically designed to provide a protective wear coat for elevated concrete surfaces in areas that are exposed to direct sunlight. Mapefloor Finish 450, in combination with the proper Mapefloor parking deck system, protects concrete substrates from water and chloride penetration while, at the same time, providing a seamless, attractive, slip-resistant wearing surface.