Self-adhered single-ply roofing membrane. Best For: Installations where the fastest, easiest, low-odor application is a key requirement.

HydroStop^™ provides fully reinforced membrane system designed to protect as a primary waterproofing membrane for a variety of substrates. ENERGY STAR^® rated systems are available with system warranties up to 25 years.

HydroStop® PremiumCoat® Butter Grade Flashing is manufactured from an acrylic resin specifically designed to provide increased tensile strength and elongation in “level out" low-lying roof areas. Its lightweight, spreadable consistency is permanently flexible and contains no plasticizers.

A low-VOC, water-based coating system that provides outstanding flame spread and penetration protection to combustible roof decks in the event of fire.

A low-VOC, water-based coating system that provides flame spread and penetration protection to combustible roof decks in the event of fire.

A water-based, low-VOC, acrylic, sprayable polymeric liquid, which cures to form a seamless rubber membrane.

TOPCOAT® Membrane is a water-based, spray-applied liquid roofing membrane.

A 60% solid elastomeric acrylic coating that provides good weatherability, ultraviolet resistance, and fire resistance for the protection of polyurethane foam.

An acrylic elastomeric coating that provides excellent durability, weatherproofing, mildew resistance, ultraviolet resistance, and fire resistance.

A high solids elastomeric acrylic coating to be used in conjunction with United Coatings™ Diathon® Base Coat to provide excellent protection of polyurethane foam.

An elastomeric acrylic coating that provides good weatherability, ultraviolet resistance, and fire retardancy for the protection of polyurethane foam.

A unique advanced acrylic elastomeric coating that provides excellent physical properties, durability, weatherproofing, dirt and mildew resistance, ultraviolet resistance, and fire resistant.

United Coatings™ Diathon® QS Roof Coating is an advanced acrylic elastomeric coating specifically developed for use over SPF substrates in a quick set formula.

United Coatings™ Diathon® Roof Coating is an advanced acrylic elastomer coating specifically developed for use over SPF substrates.

A water-based roof coating designed to coat asphalt bleed-out at the seams of installed EnergyCap™ membranes.

A water-based, liquid thermoplastic rubber coating that cures to form a seamless rubber membrane.

An effective coating for providing long-term reflectivity over a wide range of roofing substrates.

United Coatings™ Roof Mate™ Base Coat is a water-based, acrylic elastomeric base coat that is part of the Roof Mate™ Coating System.

A water-based, high-solids acrylic sealant utilizing the latest advances in acrylic technology.

A unique water-based, high-tensile, elastomeric coating utilizing the latest advances in acrylic technology.

A high-strength, water-based acrylic flashing material used to seal properly fastened horizontal seams on metal roofs.

A sprayable, water-based, low-VOC polymeric coating, which cures to form a seamless rubber membrane.

A water-based elastomeric coating utilizing the latest advances in acrylic technology in a quick set formula.

A sprayable acrylic flashing-grade material that provides a seal along seams and around fasteners on metal roofs and counter-flashing.

A water-based acrylic roof coating that provides protection from weathering, aging, and ultraviolet exposure.

A water-based, high solids elastomeric coating utilizing the latest advances in acrylic technology.

A water-based, acrylic coating without biocide.

A water-based, acrylic flashing without biocide.

A water-based acrylic roof coating that provides a durable, protective weathering layer for low-slope roofs.

An acrylic polymer dispersion system that is designed to achieve high film thickness in just one coat.

A reactive agent used to induce curing of United Coatings™ PMMA Flashing Resins, supplied as a white granular powder in premeasured packets.

A clear blended solvent used for preparing the substrate to receive United Coatings™ PMMA Flashing.

A high-performance, multicomponent flexible PMMA resin for use in the PMMA Flashing System.

A high-performance, multicomponent flexible PMMA resin for use in the PMMA Flashing System.

A non-woven, needle-punched polyester fabric reinforcement specially designed for use with the United Coatings™ PMMA Flashing System.

An innovative technology designed to deliver the proven durability and performance of traditional KYNAR® PVDF coatings.

A solvent-based, sprayable thermoplastic rubber coating, which cures to form a seamless rubber membrane.

A solvent-based, sprayable thermoplastic rubber coating.

A high-solids, moisture-cure silicone coating that provides protection for polyurethane foam insulation and other appropriate substrates.

An elastomeric silicone coating that provides excellent protection to polyurethane foam insulation and other appropriate substrates.

A thick, high-build silicone sealant featuring low odor, an easy application, a fast moisture cure, and enhanced adhesion to a variety of substrates.

A high-solids, moisture-catalyzed, single-component polyurethane base coat.

A high-solids, moisture-catalyzed, dual-component polyurethane coating.

A low-VOC, water-based coating system that provides outstanding flame spread and penetration protection to combustible roof decks in the event of fire.

An exceptional fire barrier, thermal barrier, and re-cover board with a pre-primed surface to make the bond even stronger.

An exceptional fire barrier, thermal barrier, and re-cover board used in various commercial roofing systems.

A high-performance roof board for use in low-slope roofing systems.

An ideal board for protecting your roof against the elements.

A high-density fiberboard roof insulation with unique bonding characteristics that ultimately result in excellent adhesion capabilities.

An insulation board made of glass fiber-reinforced cellulosic felt facers bonded to a core of isocyanurate foam.

A roof insulation systems that virtually eliminates ponding water.

Compatible with mechanically attached TPO, fully adhered TPO, cold-applied MB, cold-applied BUR applications, and more.

Roof insulation consisting of UltraShield™ coated glass-fiber mat facer laminated to a closed-cell polyisocyanurate foam core.

Consists of coated glass-fiber facers on both sides bonded to a core of isocyanurate foam.

A 1/2" thick high-density polyiso cover board.

A roof insulation system that virtually eliminates ponding water.

A non-halogenated polyiso insulation board that is better for the environment, since it does not contain potentially hazardous halogenated flame-retardant chemicals.

A non-halogenated ultra polyiso insulation board that is better for the environment, since it does not contain potentially hazardous halogenated flame-retardant chemicals.

A new non-halogenated polyiso insulation board that's better for the environment, since it does not contain potentially hazardous halogenated flame-retardant chemicals.

Consists of coated glass facers bonded to a core of non-halogenated isocyanurate foam.

A new non-halogenated polyiso insulation board that's better for the environment, since it does not contain potentially hazardous halogenated flame-retardant chemicals.

Sprayable, solvent-based contact adhesive.

Insulation - EnergyGuard™

Low Rise Foam Adhesives

M-Weld™ Snap-On Coping is an FM-approved and ES-1-tested coping system with 20-gauge cleat designed to channel water to the roof, eliminating the need for caulking.

This 24-gauge galvanized cleat clamps single-ply roof membrane against building like a termination bar to help prevent leaks.

Two-piece system consisting of coping clips and coping cap helps prevent leaks and save on installation costs.

Replaces traditional wood blocking or nailers at the perimeter of a low-slope roof.

EverGuard® EZ Fascia is made of formed galvanized steel, formed aluminum, or heavy-duty extruded aluminum for use with single-ply, Mod Bit, or BUR roofing systems.

Economically prefabricated metal edge for use with single-ply, modified, or BUR roof systems.

EverGuard® EZ Fascia EX clamps membrane like a termination bar and prevents wind & water from blowing under membrane.

EverGuard® Standard Drip Edge is a two-part assembly with a continuous cleat and a formed cover for low-slope roof systems.

FM-approved and ES-1-tested snap-on fascia system that is an economical solution for single-ply membranes that are less than 60-mil thick.

Large 26-gauge metal perforations ensure strong membrane-to-membrane adhesion.

Economically prefabricated metal edge for use with single-ply, modified, or BUR roof systems.

A two-piece snap-on fascia system with heavy-duty aluminum retainer to improve contractor productivity and enhance roof system performance.

FM approved and ES-1 tested two-piece snap-on fascia system with heavy-duty aluminum retainer to improve contractor productivity and enhance roof system performance.

Tested per ANSI/SPRI/FM 4435/ES-1 and easy to install.

he M-Weld™ Gravel Stop MB Fascia is easy to install and is tested per ANSI/SPRI/FM 4435/ES-1.

Free-floating aluminum fascia for use with single-ply, Mod Bit, or BUR roofing systems.

Custom sized to meet your special requirements and designed with internal straps for smooth, clean lines and ease of installation.

Custom sized to meet your special requirements and designed with internal straps for smooth, clean lines and ease of installation.

Custom sized to meet your special requirements and designed with internal straps for smooth, clean lines and ease of installation.

Eliminate the need to start with a brown roof and farm it for years, hoping and waiting for it to become a green roof. GAF is partnering with LiveRoof® to combine the proven performance of EverGuard® TPO and PVC membranes with the LiveRoof® patented, proven hybrid green roof system.

Installation

Each module arrives to the jobsite fully grown and is simply set in place on the rooftop.
During installation, the unique, patent-pending Soil Elevator™ is easily removed to allow for a seamless fit, which provides the look of a "built-in" system without the extensive, ongoing costs of maturation.

Systems offer a variety of plant options, with four system depths:

LiveRoof® Lite: For retrofit projects where load limitations exist

LiveRoof® Standard: Maximizes storm water management and integrates perfectly with both new construction and existing buildings

LiveRoof® Deep: Irrigated to expand plant biodiversity to an array of drought-resistant, conventional, and native perennials, grasses, and vegetables

LiveRoof® MAXX: Meets municipal codes in locales with 8-inch soil depth requirement; perimeter ballast supports drought-resistant perennials, grasses, and vegetables and can be used to optimize biodiversity

A walkable waterproofing system for your roof or balcony.

A water-based, penetrating sealer designed to produce a clear, semi-gloss surface sheen.

Specifically developed for use over concrete, masonry, stucco, plaster, and asphalt surfaces where a durable colored coating is required.

A high-quality, water-based acrylic coating that incorporates an epoxy additive to increase its abrasion resistance.

A waterproofing barrier for all types of masonry surfaces.

A “crack bridging" elastomeric coating designed for waterproofing exterior walls.

Sealoflex® Coraflex™ Textured Wall Coating is a resinbonded, decorative, flexible textured finish.

Sealoflex® Sealclear™ Wall Coating is a siloxane emulsion that produces a high-performance, water-repelling coating.

Sealoflex® Wearcoat™ Coating can be used on decks and balconies, concrete pathways, pool surrounds and boardwalks, mechanical rooms, structural steel, and wrought ironwork.

A liquid-applied, advanced acrylic elastomeric designed to waterproof exterior vertical surfaces.

A deep penetrating concrete/masonry sealer and water-repellent treatment.

A modified, water-based acrylic, penetrating pigmented sealer.

Enhances the appearance of asphalt surfaces and helps protect the asphalt from degradation due to oxidation from exposure to UV rays and water.

Bonds permanently, when mixed with StreetBond® SB120 Pavement Coating Part B and StreetBond® Colorant, to asphalt and concrete surfaces to provide both an enduring, and aesthetic finish.

StreetBond® SB150 Pavement Coating Part B and StreetBond® Colorant, bonds permanently to asphalt surfaces to provide both an enduring, aesthetic finish.

The perfect addition to StreetBond® SB120 or StreetBond® SB150 Pavement Coatings.

Enhances the adhesion of StreetBond® Coatings applied over asphalt surfaces with polished aggregates.

Water-Based Epoxy Fortifier & Base Coat For Stamped Asphalt; enhances the adhesion of StreetBond® coatings to polished asphalt surface aggregates.

Hardener & Aggregate Mix For Skid Resistance.

Water-Based Primer For Concrete Surfaces.

Wire rope cable stamping templates for textured, imprinted, and stamped asphalt.