Anti-Siphon Pressure Vacuum Breakers prevent the reverse flow of polluted water from entering into the potable water supply due to backsiphonage. Designed to stop contaminated water from entering into the potable water supply. Designed for use under continuous pressure. Assembly shall provide protection where a potential health hazard exists. It shall consist of bronze body construction, plastic check valve seat, stainless steel springs, a bonnet with silicone rubber O-ring seal, silicone rubber check valve disc, a lightweight plastic disc float, handles to shutoff water flow to the valve, and test cocks for winterization, draining and testing.
Manufacturer of Commercial and Industrial Plumbing and Drainage Products
Serving all of the USA, Canada, Australia and the Middle East, MIFAB can provide you with the quality, engineered plumbing and drainage solutions you need. Innovative product designs save the installer time and material cost and provides the owner with higher quality cast stainless steel drains and cleanouts for the same cost as the industry standard nickel bronze.
Continuing Education
Automatic Control Valves: Keeping the Balance:
This course educates the importance of automatic control valves, how they work and the different types of valves for each application.
The Importance of Backflow:
This course outlines how crucial backflow preventers are in a plumbing system and how they are used. The course also outlines different types of backflow devices and how they are assembled.
Guide to HDPE Interceptors:
This course educates on why there is a need for interceptors. Attendees will be able to understand the different types of interceptors and benefits of each material, the methods used for sizing interceptors, and how an interceptor effectively separates the material. The presentation shines light on the differences between gravity vs. hydromechanical interceptors before ending with the differences between IPC and UPC code requirements.
Guide to Siphonic Drainage:
This course educates on the benefits of using Siphonic drainage vs traditional gravity. Attendees will be able to understand a new method of roof drainage that utilizes smaller diameter pipe running with no pitch, a more efficient roof drain which leads to an overall safer roof with less penetrations, and lastly a look at how to utilize Siphonic drainage to be compliant with changes to code regarding sizing the roof drain based on GPM.
Trap Seal Primers Course Overview:
This course outlines how essential trap seal primers are in a plumbing system. Dry traps can be a passageway for contagious diseases by droplets, and maintain them is crucial, now more than ever. This course also outlines the various types of trap seal primers and their intended uses.
Access Doors
MIFAB® WID exterior access doors are designed to provide convenient access to any exterior application, or anywhere that requires protection against air leakage and/ or water penetration. WID doors are also designed to serve the custom air handling equipment manufacturers, as well as mechanical contractors who field assemble built-up air handling systems. All WID doors are manufactured with extruded aluminum flanged frames and door panel frames. Door panels are satin coat steel with optional stainless steel and aluminum sheet inserts. Door panels are insulated and gasketed. WID doors can be manufactured in custom sizes from 12" x 12" to 96" x 96". Available in 1″, 1 1/2″, 2″ Insulation Thickness.
MIFAB® MPFR Series fire rated access door is approved by Underwriters Laboratories Inc., for 1 1/2 hours, “B" label in walls and is approved by Warnock Hersey for 2 hours in ceilings and 3 hours in walls. The door meets ANSI-UL 10B standards. The same door can be used in walls and ceilings. Tests were conducted using mild steel and type 304 stainless steel.
MIFAB® MPFR-DW Series fire rated access door is approved by Underwriters Laboratories Inc., for 1 1/2 hours, “B" label in walls and is approved by Warnock Hersey for 2 hours in ceilings and 3 hours in walls. It meets ANSI-UL 10B standards. The same door can be used in walls and ceilings. Tests were conducted using mild steel and type 304 stainless steel. The MPFR-DW incorporates a drywall bead type of frame for a concealed frame application.
MIFAB® FHA/FHG Series floor access doors are for interior or exterior use where easy access is required. The angle frame construction with integral anchor flange is designed to be cast into concrete. They are available in either prime coated steel (FHG) or aluminum (FHA). Standard units withstand load bearing of 300 lbs. per square foot. They are designed for safety, durability and ease of operation.
MIFAB® RHA/RHG Series roof hatches are designed to provide convenient, economical access to the roofs of buildings. The are available in either white prime coated galvanized steel (RHG) or aluminum (RHA). All hatches are designed with weather resistant gasketing to ensure long life, low maintenance and ease of operation. Roof hatches install easily over the roof opening and are secured from the base flange to the roof deck.
MIFAB® MI-FVP Series flush valve panel is designed for back supply toilets and urinals where the flush valve is built into the wall. This panel allows easy access to service the flush valve by maintenance personnel. The panel provides protection to the flush valve from vandalism.
MIFAB® PA Series plastic access door is designed to provide easy access to plumbing and cables behind walls and ceilings. The door is removable from the frame and fits tightly with snap latches. The white finish can be painted or wallpapered or left as is to match the surrounding environment. This door should not be installed near any existing or potential source of excessive heat or open flame.
MIFAB® CAD Series recessed access door is designed for use in acoustical, drywall, or tiled surfaces. The door panel is recessed 5/8" (15) to allow the insertion of various types of material. Only the thickness of the door and frame edges are exposed. It has a unique white finish.
MIFAB® CAD-DW Series recessed access door is designed for use in acoustical, drywall, or tiled surfaces. The door panel is recessed 5/8" (15) to allow the insertion of various types of material. The outer frame has a galvanized drywall taping bead. Drywall cement can be applied over the beading at the same time as the wallboard joins and corners. It has a unique white finish.
MIFAB® CAD-FR Series fire resistant access door is designed for use in a suspended drywall ceiling. The CAD-FR is not fire rated. However, the combination of steel and fire rated tile supplied by others may maintain the fire resistant quality of the ceiling assembly. The door is recessed 1 1/2" (38) to accommodate dual layered ceiling tile. Consult local Fire Codes for each application.
MIFAB® CAD-PL Series recessed access door is designed for use in acoustic plaster walls and ceilings. The door panel is recessed 5/8" (15) and is lined with a self-furring metal lath to allow the insertion of plaster within the door panel. A 2 3/4" (70) wide metal lath extends from the perimeter of the frame. Only the thickness of the door and frame edges are exposed. It has a unique white finish.
MIFAB® CAD-FL Series access door is designed for flush installation in drywall or plaster surfaces. The door panel is flush with the frame. When installed flush with the wall or ceiling, only the door panel is exposed. A mounting bracket is recessed 5/8" (15) from the door. It has a unique white finish.
MIFAB® CAD-FL-PL Series recessed access door is designed for flush installation in drywall or plaster surfaces. The door panel is flush with the frame. When installed flush with the wall or ceiling, only the door panel is exposed. A 2 3/4" (70) wide metal lath on all sides provides a rigid frame. A mounting bracket is recessed 5/8" (15) from the door. It has a unique white finish.
MIFAB® MDW Series access door is designed for installation after the drywall has been applied and when a concealed outer flange is required. The outer frame has a galvanized drywall taping bead. Drywall cement can be applied over the beading at the same time as the wallboard joints and corners. Only the door is visible. It has a unique white finish.
MIFAB® UA Series is a multi-purpose access door. It is designed for flush installation into drywall, block or tile, walls and ceilings. The door features rounded safety corners, concealed hinge, flush with frame fit, a unique white finish, and a 3/8" turn back in the door panel for extra rigidity and safety.
Acid Neutralization Tanks
MIFAB® Series MI-NEUT solid construction polyethylene body with inlet and outlet, optional vent connections, acidresistant epoxy coated bolted down gasketed lid, stainless steel hardware. The tank is filled with neutralization medium, lump limestone 1″ to 3″ diameter size, water is then added to the tank to help dilution.
Backwater Valves
MIFAB® Series BV1200-R lacquered cast iron backwater valve with no hub inlet and outlet, gasketed bolted cover, automatic pvc flapper type backwater valve, lacquered cast iron extension to receive pipe extension (by others) and nickel bronze scoriated access cover.
MIFAB® Series BV1300 in-line gate type manual operated backwater valve, lacquered cast iron body with automatic PVC flapper valve and a bronze gate valve manually controlled by a recessed handle underneath the floor cover connected to a bronze non-rising threaded control rod.
BEECO (Backflow Preventers)
The Automatic Control Valve shall be a Ductile Iron Body and Cover design. The Valve shall have a resilient seal disc, guided top and bottom; Bottom guide will be vanes, sliding in a stainless steel seat arrangement, single seated line pressure operated, diaphragm actuated, pilot controlled, valve. The valve shall seal by means of a stainless steel seat. All parts are to be replaceable in the field without removing the valve from the line. All flange dimensions including face to face lengths shall conform to ISO Standards.
The Automatic Control Valve shall be a Ductile Iron Body and Cover design. The Valve shall have a resilient seal disc, guided top and bottom; Bottom guide will be vanes, sliding in a stainless steel seat arrangement, single seated line pressure operated, diaphragm actuated, pilot controlled, valve. The valve shall seal by means of a stainless steel seat. All parts are to be replaceable in the field without removing the valve from the line. All flange dimensions including face to face lengths shall conform to ISO Standards.
The ACV-HF-EOSSV shall be a Ductile Iron Body and Cover design. The Valve shall have a resilient seal disc, guided top and bottom; Bottom guide will be vanes, sliding in a stainless steel seat arrangement, single seated line pressure operated, diaphragm actuated, pilot controlled, valve. The valve shall seal by means of a stainless steel seat. All parts are to be replaceable in the field without removing the valve from the line. All flange dimensions including face to face lengths shall conform to ISO Standards.
The Automatic Control Valve shall be a Ductile Iron Body and Cover design. The Valve shall have a resilient seal disc, guided top and bottom; Bottom guide will be vanes, sliding in a stainless steel seat arrangement, single seated line pressure operated, diaphragm actuated, pilot controlled, valve. The valve shall seal by means of a stainless steel seat. All parts are to be replaceable in the field without removing the valve from the line. All flange dimensions including face to face lengths shall conform to ISO Standards.
The Automatic Control Valves shall be a Ductile Iron Body and Cover design. The Valve shall have a resilient plug seal, guided top and bottom; Bottom guide will be vanes, sliding in a stainless steel seat arrangement, single seated line pressure operated, diaphragm actuated, pilot controlled, valve. The valve shall seal by means of a stainless steel seat. All parts are to be replaceable in the field without removing the valve from the line. All flange dimensions including face to face lengths shall conform to ISO standards.
The Automatic Control Valve shall be a Ductile Iron Body and Cover design. The Valve shall have a resilient seal disc, guided top and bottom; Bottom guide will be vanes, sliding in a stainless steel seat arrangement, single seated line pressure operated, diaphragm actuated, pilot controlled, valve. The valve shall seal by means of a stainless steel seat. All parts are to be replaceable in the field without removing the valve from the line. All flange dimensions including face to face lengths shall conform to ISO Standards.'
The Automatic Control Valve shall be a Ductile Iron Body and Cover design. The Valve shall have a resilient seal disc, guided top and bottom; Bottom guide will be vanes, sliding in a stainless steel seat arrangement, single seated line pressure operated, diaphragm actuated, pilot controlled, valve. The valve shall seal by means of a stainless steel seat. All parts are to be replaceable in the field without removing the valve from the line. All flange dimensions including face to face lengths shall conform to ISO Standards.
A Water Pressure Reducing Valve with a built in strainer shall be installed in the incoming water line where supply main pressure exceeds 60psi (413 kPa). The Pressure Reducing Valve shall consist of a bronze body and metal cap, and shall have an adjustment screw to allow adjusting the pressure down to 50PSI (345 kPa), and shall be designed for incoming pressures up to 300 PSI (20.7 bar). The device must have a built in strainer that will stop debris from entering the pressure reducing chamber and is removable for cleaning. Valve shall be of the balanced piston design and shall reduce pressure in both flow and no-flow conditions.
A Water Pressure Reducing Valve with a built in strainer shall be installed in the incoming water line where supply main pressure exceeds 60psi (413 kPa). The Pressure Reducing Valve shall consist of a bronze body and metal cap, and shall have an adjustment screw to allow adjusting the pressure down to 50PSI (345 kPa), and shall be designed for incoming pressures up to 300 PSI (20.7 bar). The device must have a built in strainer that will stop debris from entering the pressure reducing chamber and is removable for cleaning. Valve shall be of the balanced piston design and shall reduce pressure in both flow and no-flow conditions.
The standard Beeco Air and Vacuum Valve (K) exhausts large quantities of air when the system is filling. The valve will remain open until the liquid has reached the float and is lifted into its seat, closing the valve. Likewise when a vacuum occurs, the float will drop, allowing air into the system to prevent pipe collapsing due to the negative pressure.
The standard Beeco Air and Vacuum Valve (K) exhausts large quantities of air when the system is filling. The valve will remain open until the liquid has reached the float and is lifted into its seat, closing the valve. Likewise when a vacuum occurs, the float will drop, allowing air into the system to prevent pipe collapsing due to the negative pressure.
The valve is designed for an efficient release of entrapped air from the pipeline, while the network is at normal working pressure. Due to the relatively large orifice, compare to other automatic valves in the market, it can also release the air through initial filling of a small-diameter pipe, or admit air into it while it is drained.
This valve has been designed for efficient discharge and intake of air in water transport systems, filtering systems, containers, and other places where confined air could impair the system's operation. The valve is appropriate for:
- Expelling the air at high flow velocity during the initial filling of the systems.
- Introducing large quantities of air when the pipe drains, maintaining atmospheric pressures in the pipe and preventing collapse and cavitation damage to the conduits.
This valve has been designed for efficient discharge and intake of air in water transport systems, filtering systems, containers, and other places where confined air could impair the system's operation. The valve is appropriate for:
- Expelling the air at high flow velocity during the initial filling of the systems.
- Introducing large quantities of air when the pipe drains, maintaining atmospheric pressures in the pipe and preventing collapse and cavitation damage to the conduits.
- Relieving the entrained air from the water, while the network is pressurized.
Check valves are mechanical valves that permit gases and liquids to flow in only one direction, preventing process flow from reversing. They are classified as one-way directional valves. Fluid flow in the desired direction opens the valve, while backflow forces the valve closed. The mechanics of check valve operation are not complicated.
Check valves are mechanical valves that permit gases and liquids to flow in only one direction, preventing process flow from reversing. They are classified as one-way directional valves. Fluid flow in the desired direction opens the valve, while backflow forces the valve closed. The mechanics of check valve operation are not complicated.
The Beeco Full Port Ball Valve is a two piece Bronze Ball Valve with a chrome plated ball. The valve has a blow out proof stem with adjustable packing. Its full port design eliminates the significant pressure losses caused by standard reduced port valves.
The Beeco Full Port Ball Valve is a two piece Bronze Ball Valve with a chrome plated ball. The valve has a blow out proof stem with adjustable packing. Its full port design eliminates the significant pressure losses caused by standard reduced port valves.
The Beeco® Silent Check Valve is designed to reduce water hammer while performing all the same requirements of a swing check valve. The Sweat Version is designed to solder into lines without disassembly; a low temperature solder should be used in order to eliminate damage to the seating surface.
The BEECO Swing Check valves are used to prevent backflow protecting system equipment. Swing check valves are used to prevent flow reversal in piping systems. They are suitable for service in horizontal or vertical flow upward installation. Swing check valves have low pressure drop and are best suited for moderate velocity applications.
The BEECO In Line Dual Check Valve prevents the reverse flow of polluted water from entering into the drinking water supply. It is designed to be used in either the horizontal or vertical position and should be placed at the service entrance or can be used as a point of use device. This device is designed for continuous pressure applications in non-health hazard residential water system containment. It should be installed right after the water meter. Check with your local inspection authorities for installation requirements.
The BEECO DCAV is designed primarily for use on boiler feed lines to prevent backflow contamination when the pressure in the supply line is below the pressure in the boiler feed line. It is designed to be used in either horizontal or vertical applications. It is designed for use under continuous pressure applications. Check with your local inspection authorities for installation requirements.
The Beeco Eccentric Plug Valve is designed to operate in clean and dirty water applications. The valve performs well in sludge and slurry liquid applications as well. The valve seals with a “drop tight" closure. The interior design allows for a full flow with very little pressure drop.
The BEECO® GV-FXF-NRS Series is an AWWA C515 flange x flange resilient seated gate valve with a non-rising stem. Flanges are to ANSI B16.1, Class 125 drilling pattern. The body, bonnet, and wedge (disc) are of high strength ductileiron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.
The BEECO® GV-FXF-NRS-MJ Series is an AWWA C515 Mechanical Joint x Mechanical Joint resilient seated gate valve with a non-rising stem. MJ bells are to AWWA C153 Standard. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.
The BEECO® Series GV-FXF-OSY is a Flanged by Flanged OS&Y (Outside Screw and Yoke) Resilient Seated Gate Valve. It is manufactured in compliance with AWWA C515 Standard. Flanges are to ANSI B16.1, Class 125 drilling pattern. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.
The BEECO® GV-FXF-UL/FM Series is a UL Listed / FM Approved OS&Y (Outside Screw and Yoke) Resilient Seated Gate Valve. It is manufactured in compliance with AWWA C515 Standard. Flanges are to ANSI B16.1, Class 125 drilling pattern. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.
The BEECO® Series GV-FXG-NRS is a Flanged x Grooved gate valve. It features a non-rising stem for use in compact areas. All flanged dimensions comply with ANSI B16.1, Class 125; Grooved dimensions comply with AWWA C606 Standard. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.
The BEECO® Series GV-FXG-OSY is a Flanged x Grooved resilient seated OS&Y (Outside Screw and Yoke) gate valve. All flanged dimensions comply with ANSI B16.1, Class 125; Grooved dimensions comply with AWWA C606 Standard. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.
The BEECO® GV-FXG-UL/FM Series is a UL Listed / FM Approved Flanged by Grooved OS&Y (Outside Screw and Yoke) Resilient Seated Gate Valve. It is manufactured in compliance with AWWA C515 Standard. Flanges are to ANSI B16.1, Class 125 drilling pattern. Grooved dimensions are to AWWA C606 Standard. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.
The BEECO® Series GV-GXG-NRS is a grooved x grooved gate valve. It features a non-rising stem for use in compact areas. All grooved dimensions comply with AWWA C606 Standard. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.
The BEECO® GV-GXG-OSY Series is a Grooved x Grooved resilient seated OS&Y (Outside Screw and Yoke) gate valve. All grooved dimensions comply with AWWA C606 Standard. The valve complies with AWWA C515 Standard. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.
The BEECO® Series GV-GXG-UL/FM is a UL Listed / FM Approved Grooved by Grooved OS&Y (Outside Screw and Yoke) Resilient Seated Gate Valve. It is manufactured in compliance with AWWA C515 Standard. Grooved dimensions are to AWWA C606 Standard. The body, bonnet, and wedge (disc) are of high strength ductile-iron, ASTM A536, Grade 65-45-12. The wedge is encapsulated with EPDM rubber. The stem and bolts are of stainless steel.
Designed for installation on potable water lines such as service sinks, laundry tubs and hose bibbs to protect against backsiphonage of polluted water into the potable water supply. Assembly shall provide protection where a potential health hazard does not exist.
Jumper Kits are used in new construction to temporarily take the place of your BEECO Pressure Reducing Valve, prior to the actual installation on potable water supply systems. The use of a this BEECO jumper permits testing of the building piping system for leaks and pressure loss and allows for flushing or construction debris prior to the installation of the water pressure reducing valve. The jumper kit reduces loss from theft or vandalism in area where there is not security around the clock. Kits consist of union connections, washers, a SS strainer and a brass pipe nipple.
Anti-Siphon Pressure Vacuum Breakers prevent the reverse flow of polluted water from entering into the potable water supply due to backsiphonage. Designed to stop contaminated water from entering into the potable water supply. Designed for use under continuous pressure. Assembly shall provide protection where a potential health hazard exists. It shall consist of bronze body construction, plastic check valve seat, stainless steel springs, a bonnet with silicone rubber O-ring seal, silicone rubber check valve disc, a lightweight plastic disc float, handles to shutoff water flow to the valve, and test cocks for winterization, draining and testing.
BEECO Style RPC Rigid Pipe Couplings provide a zero-flexibility combination of the piping system. The angle-pad design of 60 degrees adjust to steel pipes and roll/cut groove tolerances, positively clamping the pipe to resist flexural and torsion loads. Angle pad design and swing-over installation permit assembly by removing one nut/bolt and swinging housing over gasket, reducing assembly time and effort.
The Beeco Silent Check Valve is a fast-closing check valve that is designed to prevent slam when closing. It eliminates water hammer with a check valve that operates smoothly and silently itself. The Beeco SCV Series features a center guided single disc with bronze or stainless seating with special stainless steel spring control to insure positive, noiseless opening and closing.
The “Y" type strainer shall be a bronze body strainer with a bronze cap and a stainless steel mess screen. The valve shall be designed so the screen can be cleaned without removal of the valve from the pipe line and shall be equipped with a enclosure plug in the brass clean out cap for the addition of a test gauge or secondary water line.
The Ductile Iron “Y" type strainer shall be in 125 Class and conform to ANSI B16.1, and both the body and access cover shall be made of Ductile Iron A536 65-45 12. The valve shall be supplied with a drain/blow-off connection with a ductile iron closure plug. The integral strainer screen shall be accessible for cleaning without removing the device from the line.
The Ductile Iron “Y" type strainer shall be in 125 Class and conform to ANSI B16.1, and both the body and access cover shall be made of Ductile Iron A536 65-45 12. The valve shall be supplied with a drain/blow-off connection with a ductile iron closure plug and will have an FDA approved epoxy coating inside and out. The integral strainer screen shall be accessible for cleaning without removing the device from the line.
The BEECO Silent Check Valve is a fast-closing check valve that is designed to prevent slam when closing. Cast Iron Silent Check Valves are designed to prevent water hammer effect. The spring design allows the closure disc to travel further than other valves of this style, decreasing flow loss.
The BEECO® Series Barracuda 40 Reduced Pressure Valve Backflow Prevention Valve prevents non-health hazard pollutants and hazardous contaminants from entering a potable water supply system when backpressure and/or backsiphonage conditions occur. This product is designed for the waterwork, plumbing, and irrigation markets only. USC approved.
The BEECO Friendly Double Check Detector Assembly is designed to stop the reverse of flow of a liquid into a potable water system. The proper installation of a backflow preventer must be done by a certified expert under local codes and guidelines to assure the protection of the drinking water system. The Valve shall be certified to ASSE 1048, CSA B64.5 and IAPMO listed. Certified lead free devices.
The BEECO Friendly Double Check Backflow Preventer Valve is designed to stop the reverse of flow of a liquid into a potable water system. The proper installation of a backflow preventer must be done by a certified expert under local codes and guidelines to assure the protection of the drinking water system. The Valve shall be certified to ASSE 1015, CSA B64.5 and IAPMO listed.
The BEECO Friendly Double Check Backflow Preventer Valve is designed to stop the reverse of flow of a liquid into a potable water system. The proper installation of a backflow preventer must be done by a certified expert under local codes and guidelines to assure the protection of the drinking water system. The Valve shall be certified to ASSE 1015, CSA B64.5 and IAPMO listed. Certified lead free devices.
The BEECO Friendly Reduced Pressure Zone Backflow Preventer is designed to stop the reverse of flow of a liquid into a potable water system. The proper installation of a backflow preventer must be done by a certified expert under local codes and guidelines to assure the protection of the drinking water system. The Valve shall be certified to ASSE 1013, CSA B64.4 and IAPMO listed.
The BEECO Friendly Reduced Pressure Zone Backflow Preventer Valve is designed to stop the reverse of flow of a liquid into a potable water system. The proper installation of a backflow preventer must be done by a certified expert under local codes and guidelines to assure the protection of the drinking water system. The Valve shall be certified to ASSE 1013. Is Certified to cUPC and IAPMO listed.
The BEECO Friendly Reduced Pressure Zone Backflow Detector Preventer Valve is designed to stop the reverse of flow of a liquid into a potable water system. The proper installation of a backflow preventer must be done by a certified expert under local codes and guidelines to assure the protection of the drinking water system. The Valve shall be certified to ASSE 1015, Is Certified to cUPC and IAPMO listed.
C-PORT (Roof Pipe Supports)
The AP Series is designed to provide support for all electrical and HVAC equipment. Grooved recessed tray prevents movement and dampens vibration. Allows water passage; prevents growth of moss and mold. Lightweight. Consult roofing manufacturer or engineer for roof loading.
The best selling C-Port, the C Series channel support is designed for superior support of gas and refrigeration piping systems, cable tray, electrical conduit, multiple lines, HVAC equipment and hundreds of other applications.
The C510 and C6 Series provided additional height beyond the C-Series to meet various building codes. Just like the C Series they are designed for support of gas and refrigeration piping systems, cable tray, electricalc onduit, multiple lines, HVAC equipment.
The CB10 Bridge channel is designed as a superior sleeper for HVAC equipment, cable tray, roof walkway systems, refrigeration equipment and many other applications. It is UV resistant and suitable for installation on most types of roofing material or other flat surfaces.
The CE Series is designed for extended support of gas and refrigeration piping systems, cable tray, electrical conduit, multiple lines, HVAC equipment and many other applications. It is suitable for most types of roofing material or other flat surfaces.
The CES10 Series can support gas and refrigeration piping systems, cable tray, electrical conduit, multiple lines, HVAC equipment and many other applications. It is designed for rooftop applications requiring a heavier load bearing, and is suitable for most types of roofing material or other flat surfaces.
The CP36 Series is designed as a non-penetrating lightweight to bring to level platform surface. It is used for air conditioning, air condensing units, HVAC, and other electrical units. Free-flow leg system allows water passage. Other featuresinclude: prohibits moss and mold growth, easy to install, easy movement brackets that are suitable for all types of equipment, and adjustable. Consult roofing manufacturer or engineer for roof loading.
The CR10 Series is designed for superior support of gas and refrigeration pipes. The roller allows for longitudinal movements of the pipe. This support is suitable for most types of roofing material or other flat surfaces. The roller bracket has roller mounting holes 1″ apart so that the roller can be adjusted from 6″ or 7″ from the center line to the ground.
The CRE10 Series is designed for superior support of gas and refrigeration pipes at a higher elevation from the roof surface. The roller allows for longitudinal movements of the pipe. This support is suitable for most types of roofing material or other flat surfaces.
The CRM Series is the smallest C-PORT to come with a rubber roller to support gas and refrigeration pipes while allowing for small longitudinal movements. The CRM-B provides a less expensive alternative to the larger roller C-PORT. It's ideal for smaller pipes, and is adjustable in height by 1". Available with a 3" or 4" rubber roller.
CS Vari-Angle support is variable angle support designed for ventilation duct, walkway systems, HVAC equipment and many other applications installed on sloped or uneven surfaces. Adapter leg will accommodate 1 5/8" x 1 5/8" steel strut for framing. It is UV resistant and suitable for installation on most types of roofing material and sloped surfaces.
The CSE Series pipe / tubing support is engineered to support single piping systems where elevation adjustment is required.
The CXH model is the most economic and the smallest of the C-Port line, perfect for conduit and small piping.
The CZ Seismic Series is designed for superior support of gas and refrigeration piping systems, cable tray, electrical conduit, multiple lines, HVAC equipment and many other applications. This is a penetrating support fastened to the structure under the membrane. It is ideally designed for hurricane resistance or seismic applications. It is suitable for most types of roofing material or other flat surfaces.
The DSA10 Series is designed specifically for ductwork. The telescopic crossbeam allows for easy size adjustments. The bases feature vari-angle supports to adapt to any roof pitch and are made of 100% recycled rubber. Narrower bases are used with the DSA10 Series.
The CESHW12 Series can support gas and refrigeration piping systems, cable tray, electrical conduit, multiple lines, HVAC equipment and many other applications. It is designed for rooftop applications requiring a heavier load bearing, and is suitable for most types of roofing material or other flat surfaces.
The CESW12 Series can support gas and refrigeration piping systems, cable tray, electrical conduit, multiple lines, HVAC equipment and many other applications. It is designed for rooftop applications requiring a heavier load bearing, and is suitable for most types of roofing material or other flat surfaces. The wide bases provide this series with added stability. The CESW Series is suitable for use with one or two pipe hangars (by others).
The CEW12 Series channel support is designed as an extended support for gas and refrigeration piping systems, conduit and hundreds of other applications.
The CGW-E Series is on the 12″ x 12″ low-profile wide body base, giving this support series superior stability and load-bearing capacity.
The CGW-T Series is on the 12″ x 12″ low-profile wide body base, giving this support series superior stability and load-bearing capacity.
The CMPW Mechanical Platforms are designed to elevate rooftop mechanical units and other devices. CMPW Mechanical Support comes either as a frame with rails or equipped with a deck made from 12" x 2-1/2" x 13-gauge steel grating. The support bases are C-Port CXW supports. The support platforms are customizable in all dimensions per the project requirements. Consult roofing manufacturer or engineer for roof loading.
The CREW12 Series support is designed for superior support of gas and refrigeration pipes. The roller allows for longitudinal movements of the pipe. The wide-bodied base provides additional stability and load-bearing capacity. This support is suitable for most types of roofing material or other flat surfaces.
The CW Series is our economical wide body channel support. It offers additional stability and load-bearing capacity over the C Series. The CW Series is designed to support gas and refrigeration piping systems, cable trays, electrical conduit, or hundreds of other applications.
The DSAW12 Series is designed specifically for ductwork. The telescopic crossbeam allows for easy size adjustments. The bases feature vari-angle supports to adapt to any roof pitch and are made of 100% recycled rubber.
Cleanouts
MIFAB® C1460-S Series lacquered cast iron cleanout with large access area, tapered thread plug and square (specify cover size, either 7" x 7" or 9" x 9"), smooth nickel bronze access panel with allen key screwsand anchor frame with mounting lugs.
MIFAB Cleanout top assembly with 4″ machined N.P.S.M. threads. Available in 5″ diameter and in either medium duty nickel bronze (2,000 - 4,999 lbs.), or in heavy duty Type 304 stainless steel (5,000 - 7,499 lbs.) and / or “Special Duty" (over 10,000 lbs.) ductile iron. Furnished standard with vandal resistant allen key screws.
MIFAB® C1000 Series (specify top assembly design) adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and heavy duty cast stainless steel scoriated combined cover and plug top assembly with stainless steel vandal proof allen key screws and primary gasket seal. (For membrane floors, add Suffix -C for membrane clamp.).
MIFAB® C1100-R Series (specify top assembly design) adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and scoriated combined cover and plug top assembly (specify material type) with stainless steel vandal proof allen key screws and primary gasket seal. (For membrane floors, add Suffix -C for membrane clamp.)
MIFAB® C1100-RC Series adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and round nickel bronze scoriated combined cover and plug top assembly with stainless steel vandal proof allen key screws, primary gasket seal and 1 1/2" round stainless steel carpet marker. (For membrane floors, add Suffix -C for the membrane clamp.)
MIFAB® C1100-RFC Series (specify 7" or 9" for top assembly diameter) adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and heavy duty stainless steel scoriated cover with surface membrane clamp, secondary closure plug and stainless steel vandal proof allen key screws. (For membrane floors, add Suffix -C for the membrane clamp.).
MIFAB® C1100-T Series adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and round scoriated combined cover and plug top assembly (specify material type) with 1/8" recess for tile and stainless steel vandal proof allen key screws and primary gasket seal. (For membrane floors, add Suffix -C for the membrane clamp.)
MIFAB® C1100-UR Series adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and round scoriated combined cover and plug top assembly (specify material type) with 1 1/4" recess for terrazzo and stainless steel vandal proof allen key screws and primary gasket seal. (For membrane floors, add Suffix -C for the membrane clamp.)
MIFAB® C1100-XR Series adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and round heavy duty square scoriated combined cover and plug top assembly with stainless steel vandal proof allen key screws and primary gasket seal. (For membrane floors, add Suffix -C for the membrane clamp.).
MIFAB® C1200-C Series (specify top assembly design) adjustable floor cleanout with lacquered cast iron upper body and lower bodies with anchor flanges, secondary “O" ring Test Seal, cast iron membrane clamp rings for waterproofing membrane, neoprene expansion compensator, 4" cleanout opening and scoriated combined cover and plug top assembly (specify material type) with stainless steel vandal proof allen key screws and primary gasket seal.
MIFAB® C1200-C Series (specify top assembly design) adjustable floor cleanout with lacquered cast iron upper body and lower bodies with anchor flanges, secondary “O" ring Test Seal, cast iron membrane clamp rings for waterproofing membrane, neoprene expansion compensator, 4" cleanout opening and scoriated combined cover and plug top assembly (specify material type) with stainless steel vandal proof allen key screws and primary gasket seal.
MIFAB® Model C1200-C-T adjustable floor cleanout with lacquered cast iron upper and lower bodies with anchor flanges, secondary “O" ring Test Seal, cast iron membrane clamp rings for waterproofing membrane, neoprene expansion compensator, 4″ diameter cleanout opening and scoriated combined cover and plug top assembly with stainless steel vandal proof allen key screws and primary gasket seal.
MIFAB® Model C1200-C-UR Series adjustable floor cleanout with lacquered cast iron upper and lower bodies with anchor flanges, secondary “O" ring Test Seal, cast iron membrane clamp rings for waterproofing membrane, neoprene expansion compensator, 4″ diameter cleanout opening and scoriated combined cover and plug top assembly with stainless steel vandal proof allen key screws and primary gasket seal.
MIFAB® Model C1200-C-XR Series adjustable floor cleanout with lacquered cast iron upper and lower bodies with anchor flanges, secondary “O" ring Test Seal, cast iron membrane clamp rings for waterproofing membrane, neoprene expansion compensator, 4″ diameter cleanout opening and scoriated combined cover and plug top assembly with stainless steel vandal proof allen key screws and primary gasket seal.
MIFAB® C1220 Series (specify top assembly design) adjustable floor cleanout with lacquered cast iron body, secondary closure plug and scoriated combined cover and plug top assembly (specify material type) with stainless steel vandal proof allen key screws.
MIFAB® C1100-S Series adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and square scoriated combined cover and plug top assembly (specify material type) with stainless steel vandal proof allen key screws and primary gasket seal. (For membrane floors, add Suffix -C for the membrane clamp.)
MIFAB® C1100-TS Series adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and square scoriated combined cover and plug top assembly (specify material type) with 1/8" recess for tile and stainless steel vandal proof allen key screws and primary gasket seal. (For membrane floors, add Suffix -C for the membrane clamp.).
MIFAB® C1100-US Series adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and square scoriated combined cover and plug top assembly (specify material type) with 1 1/4" recess for terrazzo and stainless steel vandal proof allen key screws and primary gasket seal. (For membrane floors, add Suffix -C for the membrane clamp.)
MIFAB® C1100-XS Series adjustable floor cleanout with lacquered cast iron body and anchor flange, secondary “O" ring Test Seal, 4" diameter cleanout opening and heavy duty square scoriated combined cover and plug top assembly with stainless steel vandal proof allen key screws and primary gasket seal. (For membrane floors, add Suffix -C for the membrane clamp.)
Counterline Products
MIFAB® C220-R Series adjustable floor cleanout with lacquered cast iron body, secondary closure plug and scoriated combined gasketed cover and plug top assembly (specify material type) with stainless steel vandal proof allen key screws.
MIFAB® C220-S Series square adjustable floor cleanout with lacquered cast iron body, secondary closure plug and scoriated combined gasketed cover and plug top assembly (specify material type) with stainless steel vandal proof allen key screws.
MIFAB® C230-TS Series adjustable floor cleanout cover with lacquered cast iron body, scoriated cover (specify material type) with stainless steel vandal proof allen key screws and three anchoring set screws.
MIFAB® C300 Series R for round scoriated, C300-S for square scoriated access cover with frame (specify material) anchor lugs and vandal resistant stainless steel allen key screws.
MIFAB® F300 Series floor drain with anchor flange, primary and secondary weepholes, and standard 1" (25) thick, 7" (178) round, ductile iron tractor grate.MIFAB® Series F300 floor drain with anchor flange, primary and secondary weepholes, and standard 1" (25) thick, 7" (178) round, ductile iron tractor grate.
MIFAB® F320 Series floor drain with anchor flange, primary and secondary weepholes, and standard 1" (25) thick, 9" (229) round, ductile iron tractor grate.MIFAB® Series F320 floor drain with anchor flange, primary and secondary weepholes, and standard 1" (25) thick, 9" (229) round, ductile iron tractor grate.
MIFAB® FD240 Series lacquered ductile iron area drain with 1/2" (13) thick, 6 1/2" (165) diameter heavy duty ductile iron grate with stainless steel screws. Recommended for use in vehicular traffic areas. MIFAB® Series FD240 lacquered ductile iron area drain with 1/2" (13) thick, 6 1/2" (165) diameter heavy duty ductile iron grate with stainless steel screws. Recommended for use in vehicular traffic areas.
MIFAB® SD7000 Series Shower Drain with ABS, or lacquered cast iron body, membrane clamp, adjustable strainer with stainless steel grate.
MIFAB® MI-440 Series mild steel stack fitting with counter flashing recess, threaded stack and extension connections.
MIFAB® R100 Series lacquered cast iron roof drain with anchor flange, cast iron waterproofing membrane clamp ring with integral gravel stop, and standard self-locking polydome dome strainer with a free area of 43 square inches.
MIFAB® R100-90 Series lacquered cast iron roof drain with threaded side outlet, anchor flange, cast iron waterproofing membrane clamp ring with integral gravel stop, and standard self-locking aluminum dome strainer with a free area of 43 square inches.
MIFAB® R100-M Series lacquered cast iron roof drain with anchor flange, cast iron waterproofing membrane clamp ring with integral gravel stop, and standard self-locking metal dome strainer with a free area of 43 square inches.
MIFAB® R100-OF Series lacquered cast iron roof drain with anchor flange, cast iron waterproofing membrane clamp ring with integral gravel stop adjustable internal standpipe dam, and standard self-locking metal dome strainer with a free area of 43 square inches.
MIFAB® R150 Series combined roof drain and secondary overflow system, consisting of one piece lacquered cast iron drain body with integral sump receiver, cast iron waterproofing membrane clamp rings with integral gravel stops, one 2 1/2" (64) high integral cast iron overflow standpipe and two self-locking metal dome strainers with a free area of 43 square inches each.
MIFAB® R1800 cast metal membrane clamp lockdown clamps with 3/8" (9) hardware.
MIFAB® RFD Series replacement roof drain, fabricated stainless steel bearing pan and funnel body with lacquered cast iron dome, dome receiver and gasket seal.
MIFAB® FD212TC-S5-49 Series lacquered cast iron floor drain with anchor flange, cast iron clamp ring with weepholes for waterproofing membrane, and polished 5" x 5" square chrome plated strainer.
MIFAB® SD7000-S4 Series Shower Drain with ABS, or lacquered cast iron body, membrane clamp, and adjustable 4" x 4" square strainer with stainless steel, light duty,stamped grate.
PVC floor sinks are manufactured out of PVC material to provide the ultimate in sanitary design. PVC material has excellent resistance to chemicals such as the acids contained in fruits, vegetables and fats. The smooth, uniform surface is easy to clean and the floor sink will not chip or rust. PVC floor sinks are lightweight for easier handling, installation and transportation. PVC floor sinks are available with optional dome bottom strainer and with full, three-quarter or half PVC, nickel bronze or stainless steel grate configurations.
PVC floor sinks are manufactured out of PVC material to provide the ultimate in sanitary design. PVC material has excellent resistance to chemicals such as the acids contained in fruits, vegetables and fats. The smooth, uniform surface is easy to clean and the floor sink will not chip or rust. PVC floor sinks are lightweight for easier handling, installation and transportation. PVC floor sinks are available with optional dome bottom strainer and with full, three-quarter or half PVC, nickel bronze or stainless steel grate configurations.
MIFAB® MCL-G Series sanitary acid resistant, powder epoxy coated inside and outside fabricated 14 gauge steel hydro mechanical grease interceptor. Unit shall include: removable baffle assembly and cross bar, deep seal trap covered by lid, sewer gas stopper, securing bolt(s), external vented flow control fitting, internal air relief by pass, feet underneath interceptor to elevate it 1/2" off the ground, and steel acid resistant, powder epoxy coated, non skid, rectangular gasketed lid(s). Interceptor shall be tested and certified to the P.D.I. Standard PDI-G101 and ASME A112.14.3 and be so marked.
MIFAB® MCL-G-L Series sanitary acid resistant, powder epoxy coated inside and outside fabricated 14 gauge steel hydro mechanical grease interceptor. Unit shall include: removable baffle assembly and cross bar, securing bolt(s), external vented flow control fitting, internal air relief by pass, feet underneath interceptor to elevate it 1/2" off the ground, and steel acid resistant, powder epoxy coated, non skid, rectangular gasketed lid. Interceptor shall be tested and certified to the P.D.I. MCL-G-L-20 and MCL-G-L-35 models shall be tested and certified to the ASME Standard A112.14.3 and P.D.I. G-101.
MIFAB® MI-GO-1-PL Series HDPE economy grease interceptor with flow rating of 8 GPM and grease holding capacity pf 12 lbs. Unit shall include: two inch F.I.P. inlet and outlet connections, removable baffle, integral deep seal trap, lid securing bolts and H.D.P.E. gasketed lid.
MIFAB® MI-ROC Series sanitary acid resistant powder epoxy coated inside and outside fabricated 10 gauge steel hydromechanical grease interceptor. Unit shall include: F.I.P. inlet and outlet, cast iron drainage fittings to form a visible double wall deep seal trap, easily removable separator and filter screens, recessed, non-skid, rectangular acid resistant, powder epoxy coated gasketed lid for in or above ground use, removable cross bar, and securing bolt(s). Unit shall be complete with three F.I.P. outlet connections. Plugs are provided for the outlet connections not required.
MIFAB® MI-ROC-LO Low Rough-In Series sanitary acid resistant powder epoxy coated inside and outside fabricated 10 gauge steel hydromechanical grease interceptor. Unit shall include: F.I.P. inlet and outlet, cast iron drainage fittings to form a visible double wall deep seal trap, easily removable separator and filter screens, recessed, non-skid, rectangular acid resistant, powder epoxy coated gasketed lid for in or above ground use, removable cross bar, and securing bolt(s). Unit shall be complete with three F.I.P. outlet connections. Plugs are provided for the outlet connections not required.
MIFAB XL-MCL-G Series sanitary acid resistant, powder epoxy coated inside and outside fabricated 14 gauge steel hydro mechanical grease interceptor. Unit shall include: removable baffle assembly and cross bar, deep seal trap covered by lid, sewer gas stopper, securing bolt(s), external vented flow control fitting, internal air relief by pass, feet underneath interceptor to elevate it 1/2" off the ground, and steel acid resistant, powder epoxy coated, non skid, rectangular gasketed lid(s). Interceptor shall be tested and certified to the P.D.I. Standard PDI-G101 and ASME A112.14.3 and be so marked.
MIFAB® HY-1000-NPB Series A.S.S.E. 1019-B certified exposed type, self draining, non freeze low lead wall hydrant with A.S.S.E. 1011 approved anti-siphon and vandal resistant integral vacuum breaker with 3/4" (19) male hose connection. Hydrant assembly complete with neoprene plunger to control both the flow and drain functions, hardened bronze operating stem, drain port under the hexagon nut, heavy duty brass casing, 360 degree swivel inlet connection, heavy duty chrome plated bronze head casting and polished chrome plated face plate. Operating key to be furnished with each hydrant.
MIFAB® HY-1500 Series hydrant boxes feature a “drip lip" to drain water away from the wall to prevent unsightly staining. Standard with all of MIFAB's HY-1500-S hydrant boxes are four 1″ x 1-1/4″ slots on top and two sides of the box to receive the mounting brackets provided. Hardware is included to fasten the brackets to the box. The mounting brackets are designed to provide easy installation of the hydrant box onto the stud system for labor savings.
MIFAB® HY-1500 Series hydrant boxes feature a “drip lip" to drain water away from the wall to prevent unsightly staining. Standard with all of MIFAB's HY-1500-S hydrant boxes are four 1″ x 1-1/4″ slots on top and two sides of the box to receive the mounting brackets provided. Hardware is included to fasten the brackets to the box. The mounting brackets are designed to provide easy installation of the hydrant box onto the stud system for labor savings.
MIFAB® HY-1500-3 Series hydrant boxes feature a “drip lip" to drain water away from the wall to prevent unsightly staining. Standard with all of MIFAB's HY-1500-S hydrant boxes are four 1″ x 1-1/4″ slots on top and two sides of the box to receive the mounting brackets provided. Hardware is included to fasten the brackets to the box. The mounting brackets are designed to provide easy installation of the hydrant box onto the stud system for labor savings.
MIFAB® HY-1500-49 Series hydrant boxes feature a “drip lip" to drain water away from the wall to prevent unsightly staining. Standard with all of MIFAB's HY-1500-S hydrant boxes are four 1″ x 1-1/4″ slots on top and two sides of the box to receive the mounting brackets provided. Hardware is included to fasten the brackets to the box. The mounting brackets are designed to provide easy installation of the hydrant box onto the stud system for labor savings.
MIFAB® HY-1600 Series hydrant boxes feature a “drip lip" to drain water away from the wall to prevent unsightly staining. Standard with all of MIFAB's HY-1500-S hydrant boxes are four 1″ x 1-1/4″ slots on top and two sides of the box to receive the mounting brackets provided. Hardware is included to fasten the brackets to the box. The mounting brackets are designed to provide easy installation of the hydrant box onto the stud system for labor savings.
MIFAB® HY-2000-NPB Series A.S.S.E. 1019-B certified exposed type, self draining, non freeze low lead wall hydrant with A.S.S.E. 1011 approved anti-siphon and vandal resistant integral vacuum breaker with 3/4" (19) male hose connection. Hydrant assembly complete with neoprene plunger to control both the flow and drain functions, hardened bronze operating stem, drain port under the hexagon nut, heavy duty brass casing, 360 degree swivel inlet connection, heavy duty chrome plated bronze head casting, polished chrome plated face plate, and satin finished nickel bronze box with hinged locking cover. Operating key to be furnished with each hydrant.
MIFAB® HY-3000-NPB Series exposed type, self draining, low lead, moderate climate wall hydrant with A.S.S.E. 1011 certified antisiphon and vandal resistant integral vacuum breaker with 3/4" (19) male hose connection. Hydrant assembly complete with one piece neoprene plunger to control the flow function, hardened bronze operating stem, heavy duty chrome plated bronze head casting and polished chrome plated face plate. Operating key to be furnished with each hydrant.
MIFAB® HY-3500-NPB Series encased type, self draining. moderate climate, low lead, wall hydrant with A.S.S.E. 1011 certified anti siphon vandal resistant integral vacuum breaker.Hydrant assembly complete with one piece neoprene plunger to control the flow function, hardened bronze operating stem, heavy duty chrome plated bronze head casting, polished chrome plated face plate and satin finished nickel bronze box with hinged locking cover. Operating key furnished with each hydrant.
MIFAB® HY-4000-NPB Series A.S.S.E. 1019-B approved exposed type, self draining, non freeze hot and cold wall hydrant with A.S.S.E. 1011 approved anti-siphon integral vacuum breaker with 3/4" male hose connection. Hydrant assembly complete with hot and cold temperature control selection, one piece neoprene plunger to control the flow, hardened bronze operating stem, heavy duty brass casing, heavy duty chrome plated bronze head casing and chrome plated face plate. Loose tee key to be furnished with each hydrant.
MIFAB® HY-4100-1 hydrant box features a “drip lip" to drain water away from the wall to prevent unsightly staining. Standard with all of MIFAB's HY-4100 hydrant boxes are four 1″ x 1-1/4″ slots on top and two sides of the box to receive the mounting brackets provided. Hardware is included to fasten the brackets to the box. The mounting brackets are designed to provide easy installation of the hydrant box onto the stud system for labor savings.
MIFAB® HY-4500-NPB Series A.S.S.E. 1019-B approved encased type, self draining, non freeze hot and cold wall hydrant with A.S.S.E. 1011 approved anti-siphon integral vacuum breaker with 3/4" male hose connection. Hydrant assembly complete with hot and cold temperature control selection, one piece neoprene plunger to control the flow, hardened bronze operating stem, heavy duty brass casing, heavy duty chrome plated bronze head casting, chrome plated face plate and polished nickel bronze box with hinged locking cover. Loose tee key to be furnished with each hydrant. MIFAB® HY-4500-NPB Series A.S.S.E. 1019-B approved encased type, self draining, non freeze hot and cold wall hydrant with A.S.S.E. 1011 approved anti-siphon integral vacuum breaker with 3/4" male hose connection. Hydrant assembly complete with hot and cold temperature control selection, one piece neoprene plunger to control the flow, hardened bronze operating stem, heavy duty brass casing, heavy duty chrome plated bronze head casting, chrome plated face plate and polished nickel bronze box with hinged locking cover. Loose tee key to be furnished with each hydrant.
Wall Clamp for HY-1000-NPB, HY-2000-NPB, HY-4000-NPB, HY-4500-NPB Hydrants (Suffix -WC)
Hose connection adapter (to convert a 3/4″ M.I.P Hose) connection to a 1″ M.I.P hose connection.
Universal Repair Kit for MIFAB's Series of non freeze wall hydrants. All metal components are made from machined low lead brass.
MIFAB® HY-6000-NPB Series A.S.S.E. 1019-B certified self draining, non freeze, lawn/ground hydrant with A.S.S.E. 1011 approved anti-siphon and vandal resistant integral vacuum breaker with 3/4" (19) male hose connection. Hydrant assembly complete with one piece neoprene plunger to control both the flow and drain functions, hardened bronze operating stem, drain port under the hexagon nut, heavy duty galvanized steel pipe, heavy duty chrome plated bronze head casting, polished chrome plated face plate and satin finished nickel bronze box with hinged locking cover. Operating key furnished with each hydrant opens the hydrant, box and prevents unauthorized use. Hydrant inlet connection complete with drain port tapped for 1/8" (3) N.P.T.
MIFAB® HY-6500-NPB Series non freeze post hydrant with exposed bronze head and combination 3/4" (19) female and 1" (25) male inlet connection. Hydrant assembly complete with one piece neoprene plunger, hardened bronze operating stem, 1" (25) galvanized steel casing, heavy duty bronze head casting with head nut assembly, 3/8" (9) diameter galvanized steel operating rod, decorative casing guard, tapped 1/8" (3) drain port in the bronze tailpiece, and an operating key.
MIFAB® HY-6800-NPB Series non freeze yard hydrant with heavy duty cast iron head casting and lift handle with lock feature and combination 3/4" (19) female and 1" (25) male inlet connection. Hydrant assembly complete with neoprene plunger, hardened bronze operating stem, 1" (25) galvanized steel casing, heavy duty bronze head casting with head nut assembly, 3/8" (9) diameter galvanized steel operating rod and a tapped 1/8" (3) drain port in the bronze tailpiece.
MIFAB® HY-9040-NPB exposed type, low lead, mild climate, anti-contamination wall faucet with 3/4" (19) male hose connection and anti-siphon vacuum breaker. The body of the HY-9040-NPB is made from low lead bronze and has a rough bronze finish. Operating handle to be (specify brown plastic, clear plastic, cast iron wheel handle or operating key), and inlet connection to be (specify 1/2" (13) or 3/4" (19) F.P.T.). Vacuum breaker to be certified to the A.S.S.E. Standard 1011 and listed by I.A.P.M.O.
MIFAB® HY-9041-NPB Series exposed type, low lead, mild climate, anti-contamination wall faucet with 3/4" (19) male hose connection and anti-siphon vacuum breaker. The body of the HY-9041-NPB is made from low lead bronze and has a rough bronze finish. Operating handle to be (specify brown plastic, clear plastic, cast iron wheel handle or operating key), and inlet connection to be (specify 1/2" (13) or 3/4" (19) F.P.T.). Vacuum breaker to be certified to the A.S.S.E. Standard 1011 and listed by I.A.P.M.O.
MIFAB® HY-9200-NPB Series exposed type, low lead mild climate, anti-contamination wall faucet with 3/4" (19) male hose connection and anti-siphon vacuum breaker. The body of the HY-9240-NPB is made from low lead bronze and has a polished chrome plated finish. Operating handle to be (specify brown plastic, clear plastic, cast iron wheel handle or operating key), and inlet connection to be (specify 1/2" (13) or 3/4" (19) F.P.T.). Vacuum breaker to be certified to the A.S.S.E. Standard 1011 and listed by I.A.P.M.O.
MIFAB® MI-800 Series lacquered cast iron female threaded eccentric reducer bushing.
MIFAB® MI-860 Series of lacquered cast iron cast iron elbow adapter with male N.P.T. threaded connection by no hub outlet connection.
MIFAB® CF Series lacquered cast iron closet flange with mounting holes, stainless steel hardware and neoprene rubber gasket for waste connection.
MIFAB® MI-940 Series compact cast iron deep seal trap drain with combination funnel.
MIFAB® MI-950 Series lacquered deep seal trap with 1/2″ trap seal primer tapping and cast iron plug, 3/4″ low flushing tapping and bronze plug and 1 1/4" bottom bronze cleanout plug.
MIFAB® MI-950-F Series lacquered cast iron deep seal trap with funnel drain, with 1/2″ trap seal primer tapping and cast iron plug, 3/4″ low flushing tapping and bronze plug and 1 1/4" bottom bronze cleanout plug.
MIFAB® MI-DEGG Series galvanized steel dielectric nipples with plastic liner, designed and tested for use at temperatures up to +225 degrees F and for pressures up to 425 PSI.
MIFAB® MI-GRILL Series nickel bronze fresh air inlet with crowned and perforated round design, assembled with adjustable four point contact locking mechanism and vandal proof screw.
Couplings
MIFAB® MI-FLEX Series of flexible rubber couplings are manufactured from neoprene compound that meets the requirements of ASTM C-564 and 300 Series of stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws. MI-FLEX Series of flexible couplings are tested and certified to ASTM Standard 1173-2010 and CSA Standard B602-2016 and listed with I.A.P.M.O.
MIFAB® MI-FLEX-CC Series of flexible rubber couplings are manufactured from an elastomeric compound that meets the requirements of ASTM C-564 and 300 Series of stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws. The MI-FLEX-CC Series of flexible couplings are tested and certified to ASTM Standard 1173-2010 and CSA Standard B602-2010 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity.
MIFAB® MI-FLEX-CL Series of flexible rubber couplings are manufactured from neoprene compound that meets the requirements of ASTM C-564 and 300 Series of stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws. The MI-FLEX-CL Series of flexible couplings are tested and certified to ASTM Standard 1173- 2010 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models and listed to the National Plumbing Code of Canada and relevent Canadian Standard(s) and bear the cUPC mark of conformity.
MIFAB® Series MI-FLEX-CON (specify size) of flexible rubber couplings are manufactured from neoprene compound that meets the requirements of ASTM C-564 and 300 Series of stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws. MI-FLEX Series of flexible couplings are tested and certified to ASTM Standard 1173-2010 and CSA Standard B602-2016 and listed with I.A.P.M.O.
MIFAB® Series MI-FLEX-DTC (specify size) of flexible rubber couplings are manufactured from a flexible PVC that meets the requirements of ASTM C-564 and Type 300 Series of stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws. The MI-FLEX-DTC Series of flexible couplings are tested and certified to ASTM Standard 1173-2010 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity®. Non constant temperature rating is 140 F.
MIFAB® Series MI-FLEX-SO (specify size) of flexible rubber couplings are manufactured from neoprene compound that meets the requirements of ASTM C-564 and 300 Series of stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws. MI-FLEX Series of flexible couplings are tested and certified to ASTM Standard 1173-2010 and CSA Standard B602-2016 and listed with I.A.P.M.O.
MIFAB® Series MI-QXHUB (specify size) heavy duty shielded no hub couplings are manufactured with gaskets made from neoprene (meets the requirements of ASTM C-564) housed inside a Type 304 stainless steel corrugated shield. Four (2" through 4" size), six (5" through 12" size) Type 304 stainless steel clamps tightened with 3/8" Type 305 stainless steel hex head screws surround the shield to provide the sealing force. MI-QXHUB Series Couplings are tested and certified to the ASTM-C1540-2018 and CSA B602 Standards and listed with I.A.P.M.O. The MI-QXHUB are also tested and certified by Intertek Testing Services to the CAN/ULC S102.2-10 “Smoke Test". The MI-QXHUB are tested by IAPMO to comply to the FM 1680-1989 Standard (except for markings).
MIFAB® Series MI-XHUB heavy duty shielded no hub couplings are manufactured with gaskets made from neoprene that meets the requirements of ASTM C-564 housed inside a Type 304 stainless steel corrugated shield. Four (2" through 4" size), six (5" through 15" size) Type 304 stainless steel clamps tightened with 3/8" Type 305 stainless steel hex head screws surround the shield to provide the sealing force. MI- XHUB Series Couplings are tested and certified to the ASTM-C1540-2015 and CSA B602-2016 Standards and are listed with IAPMO. The MI-XHUB are also tested and certified by Intertek Testing Services to the CAN/ULC S102.2-10 “Smoke Test". The MI-XHUB are tested by I.A.P.M.O. to comply to the FM 1680-1989 Standard (except for markings).
MIFAB® Series MI-HUB (specify size) shielded no hub couplings are manufactured with gaskets made from neoprene that meets the requirements of ASTM C-564 housed inside a Type 301 stainless steel corrugated shield. Two (2" through 4" size), four (6" through 10" size) or six (12" and 15" sizes) Type 301 stainless steel clamps tightened with 5/16" Type 305 stainless steel hex head screws surround the shield to provide the sealing force. MI-HUB Series Couplings are tested and certified to the ASTM-#C1277-2018, CISPI 310-2010, CSA B602-2016 (File # 247608) and B70 Standards. They are listed with IAPMO and NSF certified to CISPI 310. Also tested and certified by Intertek Testing Services to CAN/ULC S102.2-07 “Smoke Test."
MIFAB® Series MI-QHUB (specify size) no hub couplings are manufactured with Quick Hub gaskets made with neoprene and three sealing rings that meets the requirements of ASTM C564 housed inside a Type 301 stainless steel corrugated shield. Two (2" through 4" size), four (6" through 10" size) or six (12" sizes) Type 301 stainless steel clamps tightened with 5/16" Type 305 stainless steel hex head screws surround the shield to provide the sealing force. MI-QHUB Series Couplings are tested and certified to the ASTM-C1277, CISPI 310, NSF, CSA B70 and CSA B602 (File # 247608) Standards and are listed with IAPMO. Also tested and certified by Intertek Testing Services to CAN/ULC S102.2 “Smoke Test." Patented Pipe Clamp for joining all types of pipe.
MIFAB® Series MI-HUB-ARC shielded repair couplings are manufactured with gaskets made from neoprene compound that meets the requirements of ASTM C-564 housed inside a Type 300 stainless steel shield. Two Type 300 stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws surround the shield to provide the sealing force. The MI-HUB-ARC Series of shielded repair couplings are tested and certified to ASTM Standard 1173-2010 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity. Non constant temperature rating is 140 F.
MIFAB® Series MI-HUB-ARC-CL shielded repair couplings are manufactured with gaskets made from neoprene compound that meets the requirements of ASTM C-564 housed inside a Type 300 stainless steel shield. Two Type 300 stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws surround the shield to provide the sealing force. The MI-HUB-ARC-CL Series of shielded repair couplings are tested and certified to ASTM Standard 1460- 2010 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity. Non constant temperature rating is 140 F.
MIFAB® Series MI-HUB-TR shielded transition couplings are manufactured with gaskets made from neoprene compound that meets the requirements of ASTM C-564 housed inside a Type 300 stainless steel shield. Two Type 300 stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws surround the shield to provide the sealing force. MI-HUB-TR Series of transition couplings are tested and certified to ASTM Standard 1460-2012 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity.
MIFAB® Series MI-HUB-TR shielded transition couplings are manufactured with gaskets made from neoprene compound that meets the requirements of ASTM C-564 housed inside a Type 300 stainless steel shield. Two Type 300 stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws surround the shield to provide the sealing force. MI-HUB-TR Series of transition couplings are tested and certified to ASTM Standard 1460-2012 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity.
MIFAB® MI-HUB-TRCC Series shielded transition couplings are manufactured with gaskets made from neoprene compound that meets the requirements of ASTM C-564 housed inside a Type 300 stainless steel shield. Two Type 300 stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws surround the shield to provide the sealing force. The MI-HUB-TRCC Series of shielded transition couplings are tested and certified to ASTM Standard 1460-2012 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity. Non constant temperature rating is 140 F.
MIFAB® Series MI-HUB-TRP shielded transition couplings are manufactured with gaskets made from neoprene compound that meets the requirements of ASTM C-564 housed inside a Type 300 stainless steel shield. Two Type 300 stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws surround the shield to provide the sealing force. The MI-HUB-TRP Series of shielded transition couplings are tested and certified to ASTM Standard 1460-2012 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity. Non constant temperature rating is 140 F.
MIFAB® Series MI-HUB-TRS shielded transition couplings are manufactured with gaskets made from neoprene compound that meets the requirements of ASTM C-564 housed inside a Type 300 stainless steel shield. Two Type 300 stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws surround the shield to provide the sealing force. The MI-HUB-TRS Series of shielded transition couplings are tested and certified to ASTM Standard 1460-2010 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity. Non constant temperature rating is 140 F.
MIFAB® Series MI-HUB-TRT shielded transition couplings are manufactured with gaskets made from neoprene compound that meets the requirements of ASTM C-564 housed inside a Type 300 stainless steel shield. Two Type 300 stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws surround the shield to provide the sealing force. The MI-HUB-TRT Series of shielded transition couplings are tested and certified to ASTM Standard 1460-2012 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity. Non constant temperature rating is 140 F.
MIFAB® Series MI-HUB-TRTW shielded transition couplings are manufactured with gaskets made from neoprene compound that meets the requirements of ASTM C-564 housed inside a Type 300 stainless steel shield. Two Type 300 stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws surround the shield to provide the sealing force. The MI-HUB-TRTW Series of shielded transition couplings are tested and certified to ASTM Standard 1460-2012 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity. Non constant temperature rating is 140 F.
MIFAB® MI-EC Series of flexible rubber end caps manufactured from neoprene compound that meets the requirements of ASTM C-564 with inside knurling for superior pipe grip and Type 300 Series of stainless steel clamp tightened with 5/16" Type 300 stainless steel hex head screw. MI-EC Series of end caps are tested and certified to I.A.P.M.O. Standard PS 90-06 and CSA Standard B602-2016 and listed with I.A.P.M.O. All models are listed to the National Plumbing Code of Canada and relevant Canadian Standard(s) and bear the cUPC mark of conformity. Non constant temperature rating is 140 F.
MIFAB® MI-EC-HB Series of flexible rubber end caps with hose bibb manufactured from neoprene compound that meets the requirements of ASTM C-564 with inside knurling for superior pipe grip and Type 300 Series of stainless steel clamp tightened with 5/16" Type 300 stainless steel hex head screw. Non constant temperature rating is 140 F.
MIFAB® Series MI-ELB of flexible rubber elbow couplings are manufactured from a flexible PVC that meets the requirements of ASTM C-564 and Type 300 Series of stainless steel clamps tightened (to 60 lbs. torque) with 5/16" Type 300 stainless steel hex head screws. The MI-ELB Series of flexible couplings are listed with I.A.P.M.O. Non constant temperature rating is 140 F.
MIFAB® MI-FLEX-DISH-1 dishwasher connector is manufactured out of a flexible PVC compound that meets the requirements of ASTM C-564. Two Type 300 stainless steel clamps tightened with 5/16" Type 300 stainless steel hex head screws provide the sealing force.
MIFAB's MI-FT-150 flexible rubber “J" bend connector is used to connect 1 1/4" or 1 1/2" Cast iron (CI), Plastic (PL), Steel (ST) or Copper (K) drain pipe to 1 1/4" or 1 1/2" Cast iron (CI), Plastic (PL), Steel (ST) or Copper (K) drain pipe or tubular trap. The flexible PVC material adjusts to pipe misalignment for an easy installation. Ideal to replace 1 1/4″ or 1 1/2″ plastic or metal p-traps. Applicable for above ground gravity (non pressure) flow applications only. 5/16″ driver required to tighten bolts to 60 lbs. torque.
MIFAB's MI-JS rolling style compression joint sealer or-ring is used to conect 4" Clay, Plastic or Steel pipe to 6" Clay, Plastic or Steel pipe in DWV systems. The MI-JS fits 4.20" through to 4.60" O.D. house pipe and fits 5.75" to 6" I.D. sewer pipe. Applicable for above ground gravity (non pressure) flow applications only.
MIFAB's MI-SCON Series of flexible PVC sealing gasket connects 2″ or 3″ Cast Iron, Schedule 40 Plastic, or Steel pipe to shower drain bodies. (American Brass & Aluminum™, Armstrong®, Casper, Garvin, Intercon, Kohler® and Schaul). No lead caulking, threading or gluing needed. For non-pressure, gravity flow applications only. Recommended for above ground installations. Easy to install and reuse.
MIFAB's MI-SPF-100 is used to repair broken toilet flanges. It permits the repair of broken toilet flanges without having to replace the entire toilet flange. Simply install the MI-SPF-100 under the broken area of the closet flange and tighten the nut. Applicable for all cast iron, plastic, copper and brass toilet flanges.
MIFAB® MI-TEE Series of flexible rubber elbow couplings are manufactured from a flexible PVC that meets the requirements of ASTM C-564 and Type 300 Series of stainless steel clamps tightened (to 60 lbs. torque) with 5/16" Type 300 stainless steel hex head screws. The MI-TEE Series of flexible tees are listed with I.A.P.M.O. Non constant temperature rating is 140 F.
MIFAB® Series MI-QHUB (specify size) no hub couplings are manufactured with Quick Hub gaskets made with neoprene that meets the requirements of ASTM C-564 housed inside a Type 301 stainless steel corrugated shield. Two (2" through 4" size), four (6" through 10" size) or six (12" sizes) Type 301 stainless steel clamps tightened with 5/16" Type 305 stainless steel hex head screws surround the shield to provide the sealing force. MI-QHUB Series Couplings are tested and certified to the ASTM-C1277-2009a, CISPI 310-2010, and CSA B602-2010 (File # 247608) Standards and are listed with IAPMO. Also tested and certified by Intertek Testing Services to CAN/ULC S102.2-07 “Smoke Test." Patented Pipe Clamp for joining all types of pipe.
MIFAB® Series MI-QXHUB (specify size) heavy duty shielded no hub couplings are manufactured with gaskets made from neoprene (meets the requirements of ASTM C-564) housed inside a Type 304 stainless steel corrugated shield. Four (2" through 4" size), six (5" through 12" size) Type 304 stainless steel clamps tightened with 3/8" Type 305 stainless steel hex head screws surround the shield to provide the sealing force. MI-QXHUB Series Couplings are tested and certified to the ASTM-C1540-2018 and CSA B602 Standards and listed with I.A.P.M.O. The MI-QXHUB are also tested and certified by Intertek Testing Services to the CAN/ULC S102.2-10 “Smoke Test". The MI-QXHUB are tested by IAPMO to comply to the FM 1680-1989 Standard (except for markings).
Dialysis Boxes
MIFAB® MI-DIAL supply and waste dialysis box is constructed of 16 gauge, Type 316 stainless steel (satin finish) continuous welded corners, four mounting anchor tabs, and removable finishing frame and door, one 1/2″ NPT PVC supply connection with PVC ball valve and 3/4″ hose connection. Bracket with grommets for two 3/8″ diameter hose, and 2" stainless steel drain connection with sloped bottom.
MIFAB® MI-DIAL-2 supply and waste dialysis box is constructed of 16 gauge, Type 316 stainless steel (satin finish) continuous welded corners, four mounting anchor tabs, and removable finishing frame and door, one 1/2″ NPT PVC supply connection with PVC ball valve and 3/4″ hose connection. Bracket with grommets for two 3/8″ diameter hose, and 2" stainless steel drain connection with sloped bottom.
MIFAB® MI-DIAL-2-LD supply and waste dialysis box is constructed of 16 gauge, Type 316 stainless steel (satin finish), continuous welded corners, four mounting anchor tabs, two 1/2" NPT PVC supply connections with PVC ball valves and 3/4" hose connections. Bracket with grommets for two 3/8" diameter hose and 2" stainless steel drain connection with sloped bottom.
MIFAB® MI-DIAL-BPS Series supply and waste dialysis box is constructed of 16 gauge, Type 316 stainless steel, continuous welded corners, four mounting anchor tabs, and removable 304 S.S finishing frame and cover 1/2" sweat supply connection, 3/4" hose connection with trap seal primer, shut off valve, reduced pressure zone backflow preventer, and 2″ NPT stainless steel drain connection.
MIFAB® MI-DIAL-CB Series supply and waste dialysis box is constructed of 16 gauge, Type 316 stainless steel, continuous welded corners, four mounting anchor tabs, and removable 304 S.S finishing frame and cover 1/2" sweat supply connection, 3/4" hose connection with trap seal primer, shut off valve, reduced pressure zone backflow preventer, and 2″ NPT stainless steel drain connection.
MIFAB® MI-DIAL-DB Series supply and waste dialysis box is constructed of 16 gauge, Type 316 stainless steel, continuous welded corners, four mounting anchor tabs, and removable 304 S.S finishing frame and cover 1/2" sweat supply connection, 3/4" hose connection with trap seal primer, shut off valve, reduced pressure zone backflow preventer, and 2″ NPT stainless steel drain connection.
MIFAB® MI-DIAL-LD supply and waste dialysis box is constructed of 16 gauge, Type 316 stainless steel (satin finish) continuous welded corners, four mounting anchor tabs, and removable finishing frame and door, one 1/2″ NPT PVC supply connection with PVC ball valve and 3/4″ hose connection. Bracket with grommets for two 3/8″ diameter hose, and 2" stainless steel drain connection with sloped bottom.
Floor and Area Drains
MIFAB® P2060, 6" x 6" Series floor drain manufactured out of 16 gauge, Type 304 stainless steel with anchor tabs and slotted Load Class “A" Light duty stainless steel ADA compliant grate. Free area of 18 square inches. Bottom outlets are available in 2", 3" or 4" no hub outlet connections (specify outlet size) and fabricated as part of the floor drain. Also available with an optional anchor flange (Suffix -FL) and B, C, D or E load rated grates.
MIFAB® P2080 Series 8" x 8" floor drain manufactured out of 16 gauge, Type 304 stainless steel with anchor tabs and slotted, Load Class “A" Light duty stainless steel ADA compliant grate. Free area of 26 square inches. Bottom outlets are available in 2", 3" or 4" no hub outlet connections (specify outlet size) and fabricated as part of the floor drain. Also available with an optional anchor flange (Suffix -FL) and B, C, D or E load rated grates.
MIFAB® P2120 Series 12" x 12" floor drain manufactured out of 16 gauge, Type 304 stainless steel with anchor tabs and slotted, Load Class “A" Light duty stainless steel ADA compliant grate. Free area of 51 square inches. Bottom outlets are available in 2", 3", 4" or 6" no hub outlet connections (specify outlet size) and fabricated as part of the floor drain. Also available with an optional anchor flange (Suffix - FL) and B, C or D load rated grates.
MIFAB® P3060 Series 6" round floor drain manufactured out of 16 gauge, Type 304 stainless steel with anchor tabs and slotted Load Class “A" Light duty stainless steel ADA compliant grate. Free area of 14 square inches. Bottom outlets are available in 2", 3" or 4" no hub outlet connections (specify outlet size) and fabricated as part of the floor drain. Also available with an optional anchor flange (Suffix –FL) and B, C, D or E load rated grates.
MIFAB® P3080 Series 8" round floor drain manufactured out of 16 gauge, Type 304 stainless steel with anchor tabs and slotted Load Class “A" Light duty stainless steel ADA compliant grate. Free area of 18 square inches. Bottom outlets are available in 2", 3" or 4" no hub outlet connections (specify outlet size) and fabricated as part of the floor drain. Also available with an optional anchor flange flange (Suffix -FL) and B, C, D or E load rated grates.
MIFAB® Series P3080-S, 8″ x 8″ square floor drain manufactured out of 16 gauge, Type 316 stainless steel with anchor flange and slotted heavy duty stainless steel grate with bead blasted finish and sediment bucket. Grate free area of 26 square inches.
Bottom outlets are available in 3″ or 4″ no hub outlet connections and fabricated as part of the floor drain.
MIFAB® Series P3100, 12" round, adjustable depth floor drain manufactured out of 16 gauge, Type 316 stainless steel with anchor flange, and slotted heavy duty stainless steel grate with bead blasted finish and sediment bucket. Grate free area of 22 square inches. Bottom outlets are available in 4″, 6″ or 8″ no hub outlet connections and fabricated as part of the floor drain.
MIFAB® P3120 Series 12" x 12" heavy duty floor drain with solid cover and perimeter drainage opening. Body is manufactured out of 16 gauge, Type 304 stainless steel. Solid cover is ½" thick Type 304 stainless steel with a Load Class “C" heavy duty cover. Free area of 8 square inches. Bottom outlets are available in 2", 3", 4" or 6" no hub outlet connections (specify outlet size) and fabricated as part of the floor drain. Also available with an optional anchor flange (Suffix –FL) and D or E load rated cover.
MIFAB® P3230, 12″ diameter, 7″ deep, 12 gauge Type 316 stainless steel area drain with funnel type body design without any inside seams or welds to eliminate hidden areas for bacteria growth. Standard with loose set heavy duty round slotted grate (1/2″ thick plate) with finger holes, 9/16″ thick top frame and bead blasted finish and sediment bucket. The P3230 meets the U.S. FDA Standards for corrosion resistance. Manufactured with either 3″, 4″ or 6″ no hub outlet connections.
MIFAB® P3230-S, 12″ square, 7″ deep, 12 gauge Type 316 stainless steel area drain with funnel type body design without any inside seams or welds to eliminate hidden areas for bacteria growth. Standard with loose set heavy duty round slotted grate (1/2″ thick plate) with finger holes, 9/16″ thick top frame, and bead blasted finish and sediment bucket. The P3230-S meets the U.S. FDA Standards for corrosion resistance. Manufactured with either 3″, 4″ or 6″ no hub outlet connections.
MIFAB® P6150 Series 1 1/2" wide, Load Class “A" Light duty slotted trench drain ADA compliant grate constructed of Type 304 stainless steel with 10 gauge stainless steel angle frame and anchor tabs. Free area of 2.0 square inches per 1′ section. Also available with B, C, D and E load rated stainless steel grates and optional anchor flange (Suffix - FL).
MIFAB® P6230 Series 3" wide, Load Class “A" Light duty slotted trench drain ADA compliant grate constructed of Type 304 stainless steel with 10 gauge stainless steel angle frame and anchor tabs. Free area of 5.25 square inches per 1' section. Also available with B, C, D and E load rated stainless steel grates and optional anchor flange (Suffix –FL)..
MIFAB® P7060, 6 5/8″ diameter, 12 gauge Type 316 stainless steel, round industrial sanitary floor cleanout with heavy duty load rated cover (1/2″ thick plate) PVC secondary plug and bead blasted finish. Cleanout meets the U.S. FDA Standards for corrosion resistance. Manufactured with either 3″ or 4″ no hub outlet connections.
MIFAB® P7060-S, 6″ square, 12 gauge Type 316 stainless steel, industrial sanitary floor cleanout with heavy duty load rated cover (1/2″ thick plate) PVC secondary plug and bead blasted finish. Cleanout meets the U.S. FDA Standards for corrosion resistance. Manufactured with either 3″ or 4″ no hub outlet connections.
MIFAB® P7080, 8 5/8″ diameter, 12 gauge Type 316 stainless steel, round industrial sanitary floor cleanout with heavy duty load rated cover (1/2″ thick plate) PVC secondary plug and bead blasted finish. Cleanout meets the U.S. FDA Standards for corrosion resistance. Manufactured with either 3″, 4″ or 6″ no hub outlet connections.
MIFAB® P7080-S, 8 5/8″ diameter, 12 gauge Type 316 stainless steel, square industrial sanitary floor cleanout with heavy duty load rated cover (1/2″ thick plate) PVC secondary plug and bead blasted finish. Cleanout meets the U.S. FDA Standards for corrosion resistance. Manufactured with either 3″, 4″ or 6″ no hub outlet connections.
MIFAB® P4080 Series 8" x 8" x 6" deep floor sink manufactured out of 16 gauge, Type 304 stainless steel with anchor tabs and slotted Load Class “A" Light duty stainless steel ADA compliant full grate. Free area of 26 square inches. Bottom outlets are available in 2", 3", 4" or 6" no hub outlet connections (specify outlet size) and fabricated as part of the floor sink. Also available with an optional anchor flange flange (Suffix -FL) and B, C, D or E load rated grates.
MIFAB® Series P4120-10D, 12″ x 12″ x 10″ deep floor sink manufactured out of 16 gauge, Type 304 stainless steel with anchor flange, sediment bucket, and heavy duty stainless steel grate with bead blasted finish. Grate free area of 51 square inches. Bottom
outlets are available in 3″ or 4″ no hub outlet connections and fabricated as part of the floor sink.
MIFAB® Series P5000, kettle drain manufactured out of 16 gauge, Type 304 stainless steel with anchor tabs and slotted Load Class “A" Light duty stainless steel loose set full grate with bead blasted finish. Bottom outlets are centered and available in 4″, 6″ or 8″ no hub outlet connections and fabricated as part of the drain. Also available with an optional anchor flange (Suffix -FL) and B, or C load rated grates.
MIFAB® P6325 Series 3.10" wide, 2" deep, 16 gauge fabricated Type 304 stainless steel presloped slot drain (1/8" per foot) with ¾" wide opening and anchor tabs. Bodies have flanged ends to connect to each other with a neoprene rubber gasket in between. End outlets are available in 2" no hub outlet connections and fabricated as part of the trench drain system.
MIFAB® P6335 Series 3.10" wide, 2 1/2" deep, 16 gauge fabricated Type 304 stainless steel presloped slot drain (1/8" per foot) with ¾" wide opening and anchor tabs. Bodies have flanged ends to connect to each other with a neoprene rubber gasket in between. End outlets are available in 2" no hub outlet connections and fabricated as part of the trench drain system.
MIFAB® P6345 Series 3.10" wide, 3 1/2" deep, 16 gauge fabricated Type 304 stainless steel presloped slot drain (1/8" per foot) with ¾" wide opening and anchor tabs. Bodies have flanged ends to connect to each other with a neoprene rubber gasket in between. End outlets are available in 2" no hub outlet connections and fabricated as part of the trench drain system.
MIFAB® P9000 Series 2 7/8" wide, 1 1/16" deep Type 304 (CF8) fabricated stainless steel linear shower drain. Complete with vertically adjustable top assembly and frame and 2" cast iron no hub center outlet connection with anchor flange and membrane clamp and light-duty satin finished stainless steel grate with square hole pattern.
MIFAB® P9000-CFL Series 2 1/2" wide, 1 1/16" deep Type 304 (CF8) fabricated stainless steel linear shower drain. Complete with anchor flange and vertically adjustable top assembly and frame, 2" stainless steel no hub center outlet connection and light-duty satin finished stainless steel grate with square hole pattern.
MIFAB® P9000-FL Series 2 1/2" wide, 1 1/16" deep Type 304 (CF8) fabricated stainless steel linear shower drain. Complete with anchor flange and vertically adjustable top assembly and frame, 2" stainless steel no hub center outlet connection and light-duty satin finished stainless steel grate with square hole pattern.
MIFAB® P9000-FL-SO Series 2 1/2" wide, 1 1/16" deep Type 304 (CF8) fabricated stainless steel linear shower drain. Complete with anchor flange and vertically adjustable top assembly and frame, 2" stainless steel no hub side outlet connection and light-duty satin finished stainless steel grate with square hole pattern.
MIFAB® P9000-TI-CFL Series 2 1/2" wide, 1 3/16" deep Type 304 (CF8) fabricated stainless steel linear shower drain with anchor flange. Complete with 2" cast iron no hub center outlet connection with anchor flange and membrane clamp and recessed tile insert frame.
MIFAB® P9000-TI-CFL Series 2 1/2" wide, 1 3/16" deep Type 304 (CF8) fabricated stainless steel linear shower drain with anchor flange. Complete with 2" cast iron no hub center outlet connection with anchor flange and membrane clamp and recessed tile insert frame.
MIFAB® P9000-TI-SO Series 2 1/2" wide, 1 3/16" deep Type 304 (CF8) fabricated stainless steel linear shower drain with anchor flange. Complete with vertically adjustable top assembly and frame, 2" stainless steel no hub side outlet connection and recessed tile insert frame.
MIFAB® P6012 Series 1 1/2" wide, 16 gauge fabricated Type 304 stainless steel presloped trench drain (1/8" per foot) with slotted Load Class “A" Light duty stainless steel ADA compliant grates. Free area of 2.0 square inches per 1′ section. Square bottom bodies have flanged ends to connect to each other with a neoprene rubber gasket in between. Bottom and end outlets are available in 1 1/2" or 2" no hub outlet connections (Specify outlet size) and fabricated as part of the trench drain system. Also available with B, C, D and E load rated stainless steel grates and optional anchor flange (Suffix - FL).