Low-Slope Roofing Systems

Our Gray EPDM membrane is used in fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. It may also be used as flexible membrane flashings for walls, curbs, etc, when installing an EPDM membrane roofing system. The system must be installed over acceptable roof insulation or other suitable substrate. 

This product is used in mechanically attached and fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. It may also be used as flexible membrane flashings for walls, curbs, etc, when installing an EPDM membrane roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate. See the MuleHide EPDM Specifications Manual for complete specifications and details.

MuleHide's SA EPDM Membrane offers excellent weatherability, hail resistance, and significant labor savings. This EPDM option also qualifies as a Low-VOC option with no solvent-related odors. SA EPDM Membrane is a nominal 60-mil non-reinforced EPDM membrane laminated to a 100%-solid pressure-sensitive adhesive and is available in 10' x 100' rolls. The release liner is silicon-coated on one side for consistent release from the adhesive. SA EPDM membrane is formulated with fire retardants to inhibit the spread of flame and can be incorporated in UL Class A systems.

Can be used as an elastomeric single-ply roofing membrane for new construction and re-roofing applications. May be installed in Ballasted and Fully Adhered roofing systems.

Our White-on-Black 60-mil and 90-mil EPDM membranes are used primarily in fully adhered roofing systems on new construction, reroofing and recover (retrofit) applications. The 60-mil membrane may also be used as flexible membrane flashings for walls, curbs, etc, when installing an EPDM membrane roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate. See our MuleHide Specifications Manual for complete specifications and details.

Our White-on-Black Reinforced EPDM membrane is used in mechanically attached and fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. It may also be used as flexible membrane flashings for walls, curbs, etc, when installing an EPDM membrane roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate. See the MuleHide EPDM Specifications Manual for complete specifications and details.

MuleHide PVC Fleece Back membrane is used in mechanically attached and fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. PVC standard membrane (non-fleece back) is to be used as flexible membrane flashings for walls, curbs, etc, when installing PVC Fleece Back roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate.

MuleHide PVC FRS utilizes Fiberglass Reinforcing Scrim, which adds dimensional stability to the membrane. It is for use on adhered roofing systems and can be used on new construction, reroofing and recover (retrofit) applications. The system must be installed over an acceptable roof insulation or other suitable substrate.

MuleHide PVC FRS Fleece Back utilizes Fiberglass Reinforcing Scrim, which adds dimensional stability to the membrane. It is enhanced with fleece for added puncture resistance, and an exceptional bond with acceptable adhesives. It is for use on adhered roofing systems and can be used on new construction, refoofing and recover (retrofit) applications. The system must be installed over an acceptable roof insulation or other suitable substrate.

Is used in mechanically attached and fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. It may also be used as flexible membrane flashings for walls, curbs, etc, when installing PVC KEE HP Membrane roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate. See the MuleHide PVC Specifications Manual for complete specifications and details.

MuleHide PVC KEE HP Fleece Back Membrane is used in fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. The polyester fleece backing enhances the puncture resistance of the membrane, and can also serve as a built-in separation layer for rough surfaces or existing asphalt-based roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate.

Is used in mechanically attached and fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. It may also be used as flexible membrane flashings for walls, curbs, etc, when installing PVC membrane roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate. See the MuleHide PVC Specifications Manual for complete specifications and detail

Is used in fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. It may also be used as flexible membrane flashings for walls, curbs, etc, when installing TPO-c membrane roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate. See the MuleHide TPO Specifications Manual for complete specifications and details.

Standard TPO is used in mechanically attached and fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. It may also be used as flexible membrane flashings for walls, curbs, etc, when installing TPO membrane roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate. See the MuleHide TPO Specifications Manual for complete specifications and details

Used in mechanically attached and fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. It may also be used as flexible membrane flashings for walls, curbs, etc, when installing TPO membrane roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate. See the MuleHide TPO Specifications Manual for complete specifications and details

Used in fully adhered and mechanically attached roofing systems in new construction, reroofing and recover (retrofit) applications. The system must be installed over an acceptable roof insulation or other suitable substrate. See the MuleHide TPO Fleece Back Specifications Manual for complete specifications and details.

TPO Fleece Back Plus Is used in fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications, where the roof membrane is adhered with hot asphalt. The system must be installed over an acceptable roof insulation or other suitable substrate. See the MuleHide TPO Fleece Back PLUS Specifications Manual for complete specifications and details

Is available with an optional CLEAN Film, a temporary protective film factory applied to the top surface of the membrane. By protecting the membrane surface from scuffs and dirt accumulation during installation, this protective film can save labor and time by helping to eliminate the need for roof cleaning upon project completion. CLEAN Film can be left in place for up to 90 days. Durable and easy to remove, CLEAN Film helps to improve the aesthetics and long-term reflectivity and is ideal for use on re-roofing, re-cover and new construction projects. CLEAN Film is available on TPO-c 60 mil membranes supplied in 6' x100' and 10'x100'rolls.

A premium fiberglass reinforced, SBS (elastomeric) modified bitumen membrane manufactured to meet the toughest code requirements of the industry. Nail Base is manufactured with a Styrene Butadiene Styrene (SBS) modified asphalt compound that exhibits exceptional waterproofing and weathering properties. Nail Base is finished with a polyolefin film with printed lay lines on the top surface.

A premium self-adhered, fiberglass reinforced, modified bitumen membrane (with fire retardant additives)* manufactured to meet the toughest code requirements of the industry. SA Base Sheet & SA Base Sheet FR are manufactured using Adeso® dual-compound technology, where the membrane consists of Styrene Butadiene Styrene (SBS) modified asphalt compound on top and a pressure sensitive adhesive compound on the bottom. The adhesive is covered with a split release liner. SA Base Sheet & Base Sheet FR are finished with a polyolefin film with printed lay lines on the top surface.

A premium self-adhering polyester reinforced modified bitumen membrane manufactured to meet the toughest code requirements of the industry. SA-APP Cap Sheet & SA-APP Cap Sheet FR are manufactured using Adeso® dual-compound technology, whereby the membrane consists of an Atactic Polypropylene (APP) modified asphalt compound on top and a pressure-sensitive adhesive compound on the bottom. The adhesive is covered with a split release liner. SA-APP Cap Sheet FR is finished with granules on the top surface, and features SEALLap® ULTRA side lap with self-adhesive compound for an instant bond, tested stronger than all other application methods and FASTLap®, granule free end lap. Each of these patented features provide for greater ease of application, as well as improved long-term performance. SA-APP Cap Sheet & SA-APP Cap Sheet FR are also used as a flashing membrane in all applicable specifications.

A highly reflective, self-adhered APP modified bitumen roofing membrane manufactured using Adeso® dual-compound technology, whereby the membrane consists of an APP (atactic polypropylene) modified asphalt compound on top and a pressure sensitive adhesive compound on the bottom. SA-APP KoolCap® & SA-APP KoolCap® FR features CURE Technology®, an innovative thin film technology attributing to exceptional granule retention, stain and discoloration resistance and UV stabilization for long-term durability and performance. CURE is solvent-free and environmentally friendly. SA-APP KoolCap® & SA-APP KoolCap® FR have a highly reflective granule surface which meets or exceeds most standards for “Cool Roofing" and has a SRI of 96.

SA-SBS Cap Sheet & SA-SBS Cap Sheet FR are a premium self-adhering polyester reinforced modified bitumen membrane manufactured to meet the toughest code requirements of the industry. SA-SBS Cap Sheet & SA-SBS Cap Sheet FR are manufactured using Adeso® dual-compound technology, whereby the membrane consists of a Styrene Butadiene Styrene (SBS) modified asphalt compound on top and a pressure sensitive adhesive compound on the bottom. The adhesive is covered with a split release liner. SA-SBS Cap Sheet & SA-SBS Cap Sheet FR are finished with granules on the top surface and features SEALLap® ULTRA side lap with self-adhesive compound for an instant bond, tested stronger than all other application methods and FASTLap®, granule free end lap. Each of these patented features provide for greater ease of application as well as improved long-term performance. SA-SBS Cap Sheet & SA-SBS Cap Sheet FR are also used as a flashing membrane in all applicable specifications.

APP Torch Base is an APP modified bitumen roofing membrane base sheet, reinforced with a fiberglass mat, saturated and coated with a polymerized asphaltic compound having exceptional waterproofing and weatherability characteristics. The top and bottom surfaces of APP Torch Base are finished with a poly film.

PP Torch Base membrane is designed for application as either a mechanically fastened or heat-welded (torch) applied base or interplay sheet. Applications include new roofing, recover (retrofit) and flashing detail. The system must be installed over an acceptable substrate or as part of a multi-ply system. APP Torch Base membrane may be used as a base sheet for self-adhered modified bitumen systems. It is not intended to be installed directly to a combustible substrate.

APP Torch Base/Cap S membrane is a polyester reinforced APP modified bitumen roofing membrane designed for heat-welded (torch) applications. Constructed with premium Atactic Polypropylene resins and incorporating superior polyester reinforcing, APP Torch Base/Cap S provides an exceptionally durable roofing product which is easy to install and will provide long-term weathering. APP Torch Base/Cap S has a smooth surface and a polyolefin backing.

A polyester reinforced APP modified bitumen roofing membrane designed for heat-welded (torch) applications. Constructed with premium Atactic Polypropylene resins and incorporating superior polyester reinforcement, APP Torch G provides an exceptionally durable roofing product which is easy to install and will provide long-term weathering. APP Torch G has a granule surface that is available in several colors, and a polyolefin backing. APP Torch G exceeds all minimum ASTM standards for tensile strength, puncture resistance and flexibility.

A premium, highly reflective, polyester reinforced APP modified bitumen roofing membrane manufactured for heat-welded (torch) applications, with a burn off bottom layer film. APP Torch G KoolCap & APP Torch G FR KoolCap has a highly reflective granule surface which meets or exceeds most standards for “Cool Roofing" and has a SRI of 96.

Constructed with premium APP resins and incorporating a non-woven polyester reinforcement, APP Torch G KoolCap & APP Torch G FR KoolCap provides an exceptionally durable roofing product with exceptional flexibility and dimensional stability. APP Torch G KoolCap & APP Torch G FR KoolCap features CURE Technology®, an innovative thin film technology attributing to exceptional granule retention, stain and discoloration resistance and UV stabilization for long-term durability and performance. CURE is solvent-free and environmentally friendly. APP Torch G KoolCap & APP Torch G FR KoolCap also feature FASTLap® technology for granule-free end laps. The membrane is solvent-free and environmentally friendly.

A premium, polyester reinforced APP modified bitumen roofing membrane (with fire retardant additives)* designed for heat-welded (torch) applications. Constructed with premium Atactic Polypropylene resins and incorporating superior polyester reinforcing, APP Torch G Premier & APP Torch G FR Premier provides an easy-to-install, long-term weathering durable roofing solution. APP Torch G Premier & APP Torch G FR Premier have a granulated surface available in several colors, a polyolefin backing and features FASTLap® technology for granular-free end laps. FASTLap provides greater ease and speed of application as well as improved long term weathering performance. APP Torch G Premier & APP Torch G FR Premier exceeds all minimum ASTM standards for tensile strength, puncture resistance and flexibility.

APP Torch S Premiere membrane is a premium, polyester reinforced APP modified bitumen roofing membrane designed for heat-welded (torch) applications. Constructed with premium Atactic Polypropylene resins and incorporating superior polyester reinforcing, APP Torch S Premier provides an easy-to-install, long-term weathering durable roofing solution. APP Torch S Premier has a sanded surface and a polyolefin backing. APP Torch S Premier exceeds all minimum ASTM standards for tensile strength, puncture resistance and flexibility.

APP Torch S Premier membrane is designed for application as a heat-welded (torch) applied base, interply or cap sheet or flashing. Applications include new roofing, recover (retrofit) and flashing details. The system must be installed over an acceptable substrate or as part of a multi-ply system. It is not intended to be installed directly to a combustible substrate.

F/G Base Sheet is manufactured from tough inorganic fiberglass mat then coated on both sides with weathering grade coating asphalt and then covered on top with white sand fines to prevent sticking in the roll. Meets ASTM D 4601-04 Type II.

Applied over the flat roofing deck or insulation as a base sheet by mechanical fasteners or hot asphalt before the application of roofing systems. This sheet is suitable for use as a vapor retarder, with a solid mopping of asphaltic material, under roof insulation or between multiple layers of insulation.

A fiberglass mat coated with an oxidized asphalt blend, which provide enhanced weathering and aging characteristics. G2 Base is designed as a base sheet for MuleHide torch applied modified roofing applications. It may also be used in built up roofing applications. It provides great tear and pull through resistance.

A premium fiberglass reinforced, SBS (elastomeric) modified bitumen membrane manufactured to meet the toughest code requirements of the industry. Nail Base is manufactured with a Styrene Butadiene Styrene (SBS) modified asphalt compound that exhibits exceptional waterproofing and weathering properties. Nail Base is finished with a polyolefin film with printed lay lines on the top surface.

A general-purpose penetrating asphalt primer used to promote adhesion prior to the application of hot-mopped, cold-applied and self-adhesive membrane systems, as well as roof cements, mastics and asphalt-based adhesives.

Tough and flexible, MuleHide #420 Mod Bit Adhesive – Brush Grade is a premium-quality, brush-grade, cold-applied bonding agent for use in installing SBS modified bitumen base sheets and SBS modified bitumen cap sheets. Fortified with high SBS content and reinforcing fibers, it delivers unsurpassed resiliency and durability. It is specially formulated for use with MuleHide self-adhering modified bitumen membranes.

• Can be used to install SBS modified bitumen base sheets and SBS modified bitumen cap sheets to a variety of substrates, including structural concrete roof decks, existing smooth-surfaced asphalt built-up roofs, approved roof insulations, and glass fiber base sheets.

• Can be used as an adhesive for APP sand back modified bitumen membranes.

• Bonds gravel or mineral granules to built-up roofing systems and modified bitumen cap sheets.

• Can be used in conventional build-up roofing systems.

MuleHide #421 Mod Bit Flashing Adhesive – Trowel Grade is a high quality formulation for use as a cold-applied bonding agent for SBS modified bitumen roof systems. Heavy, “trowel-grade" consistency makes this product ideal for flashing details, attachment of membrane to steep slopes and parapet walls and a variety of waterproofing repairs, especially at moving joints where its flexibility and elasticity make it superior to standard plastic cements. In addition, the formulation is non-destructive to asphalt based roofing membranes.

KoolCap® Touch Up is a highly reflective coating specially designed for use with our KoolCap® G membranes. It is bright white in color and is designed to help extend the life and enhance the performance of KoolCap® roofing system. KoolCap® Touch Up is a water based product and environmentally friendly.

High-quality mineral granules used on mineral-surfaced membrane products. Tough, dense, ceramic-coated particles are weather and UV resistant. Composed of a granite-like mineral permanently coated with various pigments to match MuleHide Mod Bit Cap Sheet products.

MuleHide RGA 1 Flashing Cement is the highest quality, most versatile asphalt based roof cement ever developed. This distinctive product is intended for use by quality driven roofing professionals who demand that their materials meet the highest performance standards. Its outstanding adhesion to wet, dry and even underwater surfaces allows application in any conditions. With wider usable temperature ranges, RGA 1 applies easily at seasonal temperature extremes.

A-300 Base is an acrylic based elastomeric coating. It exhibits exceptional exterior durability and UV stability, superior flexibility in low temperature environments. The A-300 Base is formulated from 100% acrylic polymers and supplied only in the color gray. This is a water-based material and must be kept from freezing. A-300 Base must be top coated with A-300 Finish.

CRRC® listed highly elastomeric coating. Exceptional durability and UV stability extends roof life. Attractive bright white reduces energy consumption. Apply by brush, roller, or airless sprayer.

A-310 Finish is a 100% Acrylic based high solids, heavy bodied elastomeric roof coating designed for all common roof substrates. Delivering the highest solids content of MuleHide acrylic coatings, A-310 forms a seamless and flexible layer of protection for your roof. This durable coating is designed to seal and dramatically reduce the surface temperatures. A-310 Finish is formulated with UV reactive chemicals for enhanced film forming characteristics and dirt pickup resistance remaining bright white after weathering.

A high tensile, superior grade water-based elastomeric coating. This proprietary formulation using 100% acrylic resins cures to form a seamless fluid applied roof membrane. A-320 Finish can be used as either a base or surface coat. This product has excellent adhesion to sprayed polyurethane foam (SPF) and a variety of other construction and roofing substrates and can exceed the expected tensile strength of typical acrylic roof coatings. This product provides excellent durability and dirt pickup resistance.

Zinc-rich, dark yellow color for easy-to-see coverage. Improves adhesion of the finish coat while it encapsulates rust and inhibits development of new rust. Apply by brush, roller, or airless sprayer.

Si TPO Primer is a primer used to promote adhesion with 100% Silicone Roof Coating to new and aged TPO roofing membranes. Si TPO Primer is manufactured from fast-evaporating solvents and adhesive resins. Primer has a blue color to allow applicator to better gauge application rates.

Highly flexible sealant for seams, penetrations, flashings, metal roof fasteners, and other areas to fill voids in the substrate. Application of product can be brushed or extruded.

Is a high quality-grade, water-based white elastomeric mastic which has exceptional workability. It cures to form a seamless flexible, waterproof membrane that will expand and contract with the movement of the roof surface. This product is designed for use at various flashing and detail conditions when installing MuleHide elastomeric roof coating systems. A-200 Flashing Fibrated offers excellent adhesion, flexibility, high tensile strength, and resistance to ultraviolet degradation.

MuleHide 115 Cleaner is a ready to use roof cleaner which easily cleans dirt, grease, oil and other foreign contamination using little or no agitation. It leaves the surface free of residue. Use it to help clean substrates prior to repairing and/or applying coatings.

One of the strongest materials available for reinforcement in cold process roofing. Offers an unusual combination of high-strength properties, delivering good elongation for excellent thermal stress force accommodations. Rolls are available in a variety of widths as well as soft or firm.

A ready-to-use, solvent borne, moisture cure silicone roof coating available in white or as tinted, which cures to form a seamless membrane when applied over the entire roof area. It also keeps the surface cool, providing protection from ultraviolet sun and other weather exposures.

MuleHide 100% Silicone Roof Coating can be applied over new spray applied polyurethane foam, EPDM, TPO, aged PVC, aged acrylic coatings, concrete, asphalt built-up roofs, granulated modified bitumen roofs and metal roofs. 100% Silicone Roof Coating is a 100% silicone-based, single part roof coating that creates a barrier that is durable, resistant to weathering, breathable, watertight and weatherproof. MuleHide 100% Silicone Roof Coating is manufactured from durable inorganic silicone resins, reinforcing and reflective pigments and silane adhesions promoters.

A single-part roof coating manufactured from durable inorganic silicone elastomers, reinforcing pigments and silaneadhesions promoters. 100% Silicone Skylight Coating is a oxime neutral cure chemistry that is not corrosive to metals. Is intended for sealing and restoring aged fiberglass skylight panels.

Zinc-rich, dark yellow color for easy-to-see coverage. Improves adhesion of the finish coat while it encapsulates rust and inhibits development of new rust. Apply by brush, roller, or airless sprayer.

Multibase SB is a 100% acrylic-based resin intended for application as a primer on approved substrates/surfaces prior to the application of MuleHide 100% Silicone Roof Coating. Multibase SB contains no mineral fillers and a minimal amount of pigment for improved adhesion.

Multibase SB blocks asphalt bleed through. Its light yellow color cures to a darker amber hue. Formulated to a relatively thin viscosity and low surface tension for complete penetration of the roof surface.

Use Multibase SB on modified bitumen, asphalt BUR, PVC, EPDM and Hypalon roof surfaces prior to applying the MuleHide 100% Silicone Roof Coatings. Do not use on coal-tar-pitch roofs, TPO membranes or any areas of ponding water.

Si TPO Primer is a primer used to promote adhesion with 100% Silicone Roof Coating to new and aged TPO roofing membranes. Si TPO Primer is manufactured from fast-evaporating solvents and adhesive resins. Primer has a blue color to allow applicator to better gauge application rates.

A high-solids non-shrinking moisture cure silicone sealant intended for sealing and repairing roofs, masonry, architectural metal and metal roof seams & fasteners. Minimal odor, contains no solvents and less than 10 grams per liter VOC. Use to seal penetrations and terminations prior to application of MuleHide 100% Silicone Roof Coating. Excellent adhesion to concrete, masonry, polyurethane foam, EPDM, aged PVC, aged acrylic coatings, granular cap sheet, wood, metals, Kynar®and most other common building materials. Si TPO Primer is required for application TPO roofs.

MuleHide 115 Cleaner is a ready to use roof cleaner which easily cleans dirt, grease, oil and other foreign contamination using little or no agitation. It leaves the surface free of residue. Use it to help clean substrates prior to repairing and/or applying coatings.

One of the strongest materials available for reinforcement in cold process roofing. Offers an unusual combination of high-strength properties, delivering good elongation for excellent thermal stress force accommodations. Rolls are available in a variety of widths as well as soft or firm.

Seal-Fast® Liqui-Flash is a flashing grade single component polyurethane roof sealant used in the construction of liquid flashing systems and sealing pitch pockets and pans, metal roof seams & fasteners, inlaid gutters, polyurethane foam, Asphalt, Modified Bitumen, PVC, and EPDM roofs. It may also be used on TPO roofs when primed with Low VOC Primer. Liqui-Flash is compatible with acrylic and silicone roof coatings. It is ideal for repairing hail damaged polyurethane foam roofs. It may also be used in conjunction with custom manufactured Shape Shift and metal pitch pockets which can be combined to produce pans of various sizes and shapes.

Colored EPDM granules specially formulated to provide a non-slip surface for walkways and traffic areas where foot traffic is expected on a MuleHide Silicone Roof Coating. Walkway Granules may be embedded in the surface of the silicone roof coating to provide a more durable, damage and slip resistant surface.

SPF+ 2.5 HFO is a sprayed-in-place, nominal 40 psi compressive strength, rigid, HFO-blown, closed-cell spray polyurethane foam (SPF) roofing system. This two-component SPF consists of SPF+ 2.5 HFO B component resin and SPF ISO A component. SPF+ 2.5 HFO provides an R-value of 6.7 per inch and a continuous insulation without thermal breaks. SPF+ 2.5 HFO roofing systems provide excellent wind uplift resistance, are self-flashing, seamless, and the closed-cell nature provides a durable, leak-resistant roofing system.

SPF+ 2.8 HFO is a sprayed-in-place, nominal 60 psi compressive strength, rigid, HFO-blown, closed-cell spray polyurethane foam (SPF) roofing system. This two-component SPF consists of SPF+ 2.8 HFO B component resin and SPF ISO A component. SPF+ 2.8 HFO provides an R-value of 6.7 per inch and a continuous insulation without thermal breaks. SPF+ 2.8 HFO roofing systems provide excellent wind uplift resistance, are self-flashing, seamless, and the closed-cell nature provides a durable, leak-resistant roofing system.

SPF+ 3.0 HFO is a sprayed-in-place, nominal 70 psi compressive strength, rigid, HFO-blown, closed-cell spray polyurethane foam (SPF) roofing system. This two-component SPF consists of SPF+ 3.0 HFO B component resin and SPF ISO A component. SPF+ 3.0 HFO provides an R-value of 6.7 per inch and a continuous insulation without thermal breaks. SPF+ 3.0 HFO roofing systems provide excellent wind uplift resistance, are self-flashing, seamless, and the closed-cell nature provides a durable, leak-resistant roofing system.

A general-purpose penetrating asphalt primer used to promote adhesion prior to the application of hot-mopped, cold-applied and self-adhesive membrane systems, as well as roof cements, mastics and asphalt-based adhesives.

A general purpose asphalt repair product for use as a repair material in many types of asphalt roof membranes. MuleHide #210 Plastic Cement has a heavy “trowel-grade" consistency that will not separate.

A general-purpose, cold-applied cement that is ideal for use in sealing and repairing many types of asphalt-based roof membranes.

• Can be used to repair conventional built-up roofs, asphalt shingles, metal, and masonry surfaces.

• Can be used to seal leaks and openings around flashings, such as chimneys, vents, skylights, metal joints, gutters, and similar components of built-up flashings.

A versatile, professional-grade performer, MuleHide #221 Wet/Dry Roof Cement is an all-weather, asphalt-based flashing cement ideally suited to repairing leaks in many types of asphaltic roofing membranes. It can be applied to wet or dry surfaces. Its heavy, trowel-grade consistency makes it ideal for sealing and patching temporary emergency holes and cracks in roofs, even in standing water.

• Can be used to repair conventional built-up roofs, asphalt shingles, metal roofs, and masonry surfaces.

• Seals leaks and openings around all types of flashings, including chimneys, vents, skylights, metal joints, gutters, and similar components of built-up flashings.

A professional-grade, all-weather, cold-applied flashing cement ideally suited for use with many types of asphalt roofing membranes.

• Can be used to repair conventional built-up roofs, asphalt shingles, metal roofs, and masonry surfaces.

• Seals leaks and openings around all types of flashings, including chimneys, vents, skylights, metal joints, gutters, and similar components of built-up flashings.

• Can be used for positive-side damp-proofing of concrete, masonry walls, and foundations.

A professional-grade, rubber-modified mastic designed for use as a cold-applied bonding agent in SBS modified bitumen roofing systems. A versatile performer, it can be used on all types of penetrations, on wet or dry surfaces, and in all weather conditions. Its flexibility and elasticity make it superior to standard plastic and flashing cements, particularly where there are moving joints.

• Ideal for installing SBS modified bitumen membrane flashings to parapet walls, curbs, steep slopes, and roof penetrations.

• Seals laps and perimeter edges of SBS modified bitumen roofing membranes.

• Can be used on flashings around skylights and gutters and in crevices.

• In repair applications only, it may be used as a topical application on smooth or granulated APP modified bitumen roofing products.

• Repairs splits, breaks and small holes in asphalt-based roofing and flashings.

• Seals joints of metal flashings and coping caps.

• Can be used to install metal edge flanges and seal gutter seams, air-conditioning ducts and other metal joints.

Tenacious under extreme conditions, MuleHide #251 Wet/Dry Elastomeric Flashing Cement is a cold-applied bonding agent formulated for making wet repairs of leaks in many asphaltic roofing membranes and SBS modified bitumen roofing systems. Fortified with SBS rubber, it is ideal for sealing and patching temporary emergency holes and cracks in roofs, even in standing water. It also can be used to make emergency repairs on built-up roofing (BUR) systems, shingles and concrete, as well as for general damp-proofing.

• Used to install SBS modified bitumen membrane flashings to parapet walls, curbs, and roof penetrations.

• Ideal for making waterproofing repairs, particularly in moving joints.

• Seals laps and perimeter edges of self-adhering modified bitumen membranes.

• In repair applications only, it may be used as a topical application on smooth or granulated APP modified bitumen roofing products.

• Repairs splits, breaks and small holes in asphalt-based roofing and flashings in wet and dry conditions.

• Can be used to install metal edge flanges and seal gutter seams, air-conditioning ducts and other metal joints.

• Can be used for positive-side damp-proofing of concrete, masonry walls, and foundations.

A durable, fiber-reinforced asphalt roof coating that forms a weather resistant film with excellent adhesion to most surfaces.

• Protects smooth-surfaced and granulated built-up roofs, modified bitumen (APP and SBS) membranes, and roll roofing membranes

• Performs well as an adhesive for mineral granules

• Suitable for use as an adhesive for organic roll roofing membranes

A professional-grade asphalt roof coating that forms a weather resistant film with excellent adhesion to most surfaces.

• Designed to be used as a protective coating on smooth-surfaced and granulated built-up roofs, modified bitumen (APP and SBS) membranes, and roll roofing membranes

• Performs well as an adhesive for mineral granules

• Protects metal roofing, masonry, stucco, parapet walls, curbs, and base flashings

• Suitable for use as an adhesive for organic roll roofing membranes

• Can be used as a damp-proofing compound for below-grade walls

• Can be used to protect the inside of planter boxes

A general-purpose penetrating asphalt primer used to promote adhesion prior to the application of hot-mopped, cold-applied and self-adhesive membrane systems, as well as roof cements, mastics and asphalt-based adhesives.

MuleHide #311 Non-Fibrated Emulsion Roof Coating stands up to heat, rain and snow and is particularly at home in hot climates. The asphalt-based clay emulsion roof coating protects smooth-surfaced asphalt built-up roofs and modified bitumen roofing membranes. It does not flow when applied in thick coats. When dry, it stays firmly in place, even when exposed to elevated temperatures.

• Good when used as a base coat prior to application of aluminum or elastomeric coatings.

• Effective as a base coat for reflective coatings.

• Also protects metal roofing, masonry, stucco, parapet walls, curbs, and base flashings.

• Effective in damp-proofing below-grade walls.

• Can be used as a protective coating on the inside of planter boxes.

MuleHide #401 Premium Fibrated Aluminum Roof Coating provides unsurpassed protection for asphalt-based roofs, extending their service lives by creating a powerful shield against damaging heat, ultraviolet radiation, mold, fungus and rust. With a premium amount of aluminum pigment per gallon, the heavy-bodied roof coating delivers maximum reflectivity.

• Designed for application to new or existing APP or SBS modified bitumen cap sheets (smooth and granulated), asphalt built-up roofs, and flashings.

• Can be used to coat a variety of other substrates, including masonry surfaces, and structural steel.

• Should only be applied to areas with positive drainage.

• Product must be mixed very well with a power drill until coating appears silver. Hand mixing is not satisfactory. Average mix time per bucket should be approximately 2 minutes.

MuleHide #406 Standard Fibrated Aluminum Roof Coating provides high-performance protection for asphalt-based roofing systems, extending their service lives by shielding them from damaging heat, ultraviolet light, mold, fungus and rust. The heavy-bodied coating delivers excellent reflectivity.

• Designed for application to new or existing APP or SBS modified bitumen cap sheets (smooth and granulated), asphalt built-up roofs, and flashings.

• Can be used to coat a variety of other substrates, including masonry surfaces, and structural steel.

• Should only be applied to areas with positive drainage.

• Product must be mixed very well with a power drill until coating appears silver. Hand mixing is not satisfactory. Average mix time per bucket should be approximately 2 minutes.

MuleHide #410 Premium Non-Fibrated Aluminum Roof Coating provides premium, high-performance protection for asphalt-based roofs. MuleHide #410 Premium Non-Fibrated Aluminum Roof Coating is easier to spread and provides greater coverage. This formula is non-destructive to asphalt based roofing membranes. Formula produced with premium amounts of aluminum pigment per gallon for maximum reflectivity.

MuleHide #416 Standard Non-Fibrated Aluminum Roof Coating delivers high-performance protection for asphalt-based roofing systems, extending their service lives by shielding them from damaging heat, ultraviolet light, mold, fungus and rust. The heavy-bodied coating delivers excellent reflectivity. It is easier to spread and provides greater coverage than fibrated aluminum roof coatings.

• Designed for application over new or existing APP or SBS modified bitumen cap sheets (smooth and granulated), asphalt built-up roofs and flashings.

• Can be used to coat a variety of other substrates, including storage tanks, masonry surfaces, and structural steel.

• Should only be applied to areas with positive drainage.

• Product must be mixed very well with a power drill until coating appears silver. Hand mixing is not satisfactory. Average mix time per bucket should be approximately 2 minutes.

Drill Point Fasteners (#12) are specifically engineered to secure insulation, coverboards and base sheets to corrugated steel (16 – 22 ga.) and wood substrates. Featuring a #2 double flute self-drilling point and exclusive tapered entry thread design, penetrating steel quickly and offering exceptional back-out resistance. Available with #3 Phillips Head.

EHD Fastener (#15) is engineered for lap attachment to corrugated steel (18 – 22 ga.) and wood substrates in higher wind uplift roof assemblies. Featuring a #2 double flute self-drilling point and exclusive tapered entry thread design, penetrating steel quickly and offering exceptional back-out resistance.

HDP Fastener (#14) is engineered to secure insulation, coverboards, base sheets and single-ply roof membrane systems to corrugated steel (16 - 22 ga.), wood, and concrete substrates. Featuring a #2 double flute self-drilling point and exclusive tapered entry thread design, penetrating steel quickly and offering exceptional back-out resistance.

LWG Fasteners are engineered to secure insulation, cover boards and base sheets to lightweight insulating concrete (LWIC) and gypsum decks. The LWG Fastener features an exclusive thread design engineered for exceptional pullout. When used in conjunction with the LWG 3" Metal Plate, multiple fasteners can be installed to achieve the required minimum pullout.

PFC Purlin Drill Point (#12) is a self-drilling fastener engineered to secure single-ply roofing membrane to structural steel purlins (16 ga. to 3/16") in standing seam metal roof recover applications. The specially designed 3/4" long pilot point prevents the existing metal roof panel from jacking up the threads during the drilling operation, thereby reducing point burnout and breakage.

Pre-Assembled Fastener System offers a simple, economical and ergonomic “system solution" to increase the productivity in the mechanical attachment of roof insulation boards. The system includes a pre-assembled Drill Point Fastener (#12) with Phillips head style and 3" Galvalume Plate or a Drill Point Fastener (#12) with 1/4" Hex head style and 3" Recessed Galvalume Plate, a Magnetic Setter Tool, 29" Stand-up Electric Power tool and a Canvas Fastener Bag.

The lightweight and easy to maneuver Stand-Up Power Tool allows the operator to quickly and comfortably drive the fasteners to the proper depth without special training.

TL Fastener is designed to mechanically attach rigid insulation board and single-ply membrane to structural cement wood fiber, gypsum and lightweight insulating concrete roof decks. Features a high-thread profile with a tapered root diameter and sharp point. Its unique design allows it to penetrate the roof deck and progressively compact the base material, creating a stronger hold in weak material. Used in conjunction with the 2" TL Seam Plate and 3" TL Insulation Plate.

Tru-Spike Fastener is a one-piece, vibration-resistant anchor designed to attach insulation, single-ply roofing, wood and steel to structural concrete roof decks and walls. Featuring an “S" shaped configuration at the working end to create an expansion mechanism, it provides a fast, reliable fastening solution for roof applications over structural concrete surfaces.

The 2" TL Seam Plate is used to attach reinforced single-ply and modified bituminous membranes to cementitious wood fiber, gypsum and lightweight concrete substrates. Use with MuleHide TL Roofing Fastener.

A round Galvalume-coated metal plate with (14) barbed anchors and reinforcing ribs for superior wind uplift resistance. Designed for the mechanical attachment of the MuleHide Reinforced EPDM, PVC and TPO membranes. The 2.4" Seam Plates can also be used with MuleHide HDP Fasteners, EHD Fasteners, reinforced 6" wide RMS or 6" wide and 10" wide RUSS™ Strip.

3" Insulation Plates are round Galvalume-coated metal plates with reinforcing ribs for superior wind uplift resistance. Designed specifically for the mechanical attachment of MuleHide Poly ISO insulation boards and other FM Approved insulation/cover boards.

LWG 3" Metal Plates are used to mechanically attach insulation, cover boards and base sheets to lightweight insulating concrete (LWIC) and gypsum decks. The LWG 3" Metal Plate is a circular design with one center fastener placement hole and eight equally spaced fastener placement holes around the perimeter of the plate allowing for maximum versatility. Required pullout values can be achieved by installing multiple LWG Fasteners in one LWG 3" Metal Plate.

The 3" TL Insulation Plate is used to attach roof insulation, coverboards and BUR base sheets to cementitious wood fiber, gypsum and lightweight concrete substrates. Use with MuleHide TL Roofing Fastener.

Cardboard Discs are used when induction weld systems are being installed over expanded or extruded polystyrene insulation to prevent the plates from melting the insulation or cause depressions in the insulation which can lead to ponding and ultimately roof damage.

The Induction Weld Plates are designed to attach insulation or coverboards to the deck while providing a non-penetrating mechanical attachment of TPO or PVC singly-ply membranes utilizing an induction weld bond to the Induction Weld Plate. Induction Weld Plates are approximately 3-3/8" in diameter. Plates are approved for use with steel, wood or structural concrete roof decks. The Induction Weld Plates can be installed using #15 EHD, Tru-Spike Fasteners, and PFC Purlin Drill Point Fasteners.

The RhinoBond TPO or PVC Fastening Plate is designed to attach the roofing membrane from the underside using the RhinoBond induction-welding tool.

All Purpose Bar is designed for use as an anchor bar for attachment of MuleHide EPDM membranes. May be installed in the field seam as a batten bar and used at the base of curbs, parapet walls and angle changes as an anchor bar. Also be used with any MuleHide single-ply membranes as a termination bar. Refer to the MuleHide Single-Ply Manuals for specific use and installation instructions.

RD-100 Retaining Drainbar is made from special extruded aluminum without sharp edges providing a smooth sealant ledge against the roofing material and is be used with ballasted or non-ballasted systems. This product is available in 10' lengths with slotted mounting holes 6" on center and slotted drainage holes that are 4" on center.

TB-125 Termination Bar is made from special extruded aluminum without sharp edges providing a smooth flat surface with no ledge against the roofing material.

The TB-75 Termination Bar with sealant ledge is made of extruded aluminum alloy with a mill finish. It is designed to terminate single-ply membrane to parapet walls and other penetrations.

TB-90 Termination Bar is made from special extruded aluminum without sharp edges providing a smooth flat surface with no ledge against the roofing material.

Cant Strip and Tapered Edge are widely accepted, high quality low-slope roofing products. Each is durable, lightweight and environmentally friendly. These components are factory fabricated from Blue Ridge Fiberboard Structodek insulation board. The Cant Strips are cut at angles that provide a true 45-degree angle between horizontal and vertical surfaces. The Tapered Edge is cut on angles that slope from zero on one edge to ½" to 2″ thickness on the opposite edge.

DensDeck Prime Roof Boards by Georgia-Pacific Gypsum are a patented design features a gypsum core with embedded glass mat facers on the top and bottom of the board. DensDeck Prime can be used in a variety of commercial roof systems and provides an excellent thermal barrier as well as exceptional fire, moisture, and wind uplift resistance properties.

DensDeck Prime is typically used as a cover board over insulation in fully adhered EPDM, TPO, and PVC applications. It is compatible with solvent-based bonding adhesives. For applications in which Helix Max is used to attach insulation and a vapor barrier is specified, DensDeck Prime can be used as a base layer for MuleHide's F5 Air and Vapor Barrier (in conjunction with Aeroweb). DensDeck Prime is also compatible with hot asphalt and can be used as a membrane underlayment in hot mopped roofing systems or as a parapet wall substrate in all systems.

MuleHide Poly ISO 1-HD is 1/2" thick, 100 psi high density polyisocyanurate insulation board specifically designed for use as a cover board. Consists of a closed-cell polyisocyanurate foam core laminated to premium performance coated glass fiber felt facers. MuleHide Poly ISO 1-HD is designed for use as a cover board over roof insulation boards or existing membranes. Compatible with single-ply roofing systems (ballasted, mechanically attached and fully adhered) and modified bitumen roofing systems, on new construction, tearoff and recover (retrofit) projects. Suitable for use with approved fasteners and plates, and low-rise foam adhesive. Poly ISO 1-HD can achieve a FM hail resistance rating of SH-1 with certain membranes.

MuleHide Poly ISO 1-HD Plus is an FM-approved, ½" thick high density polyisocyanurate insulation board that was specifically designed for use as a cover board in fully adhered systems. Suitable for both re-roofing and new construction applications, Poly ISO 1-HD Plus consists of a closed-cell polyisocyanurate foam core laminated to premium performance coated glass fiber felt facers. Poly ISO HD-1 Plus has an R-value of 2.5, which is significantly higher than roof cover boards made with other materials such as wood fiber or gypsum.

MuleHide Poly ISO 1-HD80 is a ½" thick, high-density polyisocyanurate insulation board that was specifically designed for use as a cover board with mechanically attached and induction welded single-ply roofing systems only. Suitable for use with approved fasteners and plates. This product consists of a closed-cell polyisocyanurate foam. In addition to providing a durable underlayment for roofing membranes, Poly ISO 1-HD80 has an R-value of 2.5 which is significantly higher than that of other cover board products such as wood fiber or gypsum.

The non-asphaltic primed red coating integrated on the surface possesses superior adhesion capabilities with current membrane and adhesive technology. The non-asphaltic primed red coating is compatible with all single-ply membranes including PVC, TPO and EPDM, as well as modified bitumen and BUR without concern of premature membrane degradation that is often associated with asphalt emulsion coated fiberboard products. Additionally, the Primed Red Coating, unlike asphalt emulsion coated products, has proven to be compatible with traditional, low-VOC and water-based adhesives as well as many foam adhesives.

DensDeck® Roof Boards by Georgia-Pacific Gypsum are utilized in a wide variety of roofing systems for new and re-roofing applications as cover boards and thermal barriers. Featuring a combination of fire resistance, strength and dimensional stability, DensDeck roof boards enhance the performance of all roofing assemblies and are widely respected by leading roofing system manufacturers and consultants.

DensDeck® StormX Prime Roof Boards by Georgia-Pacific Gypsum are a reinforced gypsum cover board with an enhanced, moisture-resistant core and coated glass mat facers. DensDeck StormX is extremely durable and is approved for use in assemblies meeting FM's Very Severe Hail (VSH) Classification.

USG SECUROCK Glass-Mat Roof Board is a high-performance roof board used in mechanically attached low-slope roofing systems. This material features a specialty treated core and high-performance glass-mat facers for protection against fire, mold, and moisture.

Gypsum-fiber roof board is a high-performance roof board for use in low-slope roofing systems. Its unique, fiber-reinforced, homogenous composition gives the panel strength and water resistance through to the core. Securock® roof boards provide exceptional bond and low absorption in adhered systems and with its homogenous composition achieves high wind-uplift ratings with no risk of facer delamination. Made from 97% recycled material, Securock® roof boards combine superior performance with sustainable design for all types of roofing systems including single-ply, fluid-applied, built-up, spray foam, metal and modified bitumen roofing.

USG Securock UltraLight Coated Glass-Mat Roof Board is a high-performance roof board for use in low-slope roofing systems. This material features a specialty treated core and high-performance glass-mat facers for protection against fire, mold, and moisture. The top facer has been coated for adhered applications.

Flat Roof Insulation provides high long-term R-Values and saves labor installation time. Suitable for use with all roofing membrane materials, expanded polystyrene (EPS) roof insulation is compatible with loose-laid and attached single-ply membranes, conventional built-up roofing or modified bitumen systems. Flat Roof Insulation is unfaced EPS and is suitable for use with loosely laid single-ply membranes. Flat EPS Roof Insulation is also used with conventional BUR and mechanically or adhesively attached single-ply and modified bitumen membranes when field-applied cover boards are used.

Tapered Roof Insulation was developed more than 30 years ago with a dual purpose in mind: to drain and insulate dead-level roof decks. Manufactured from lightweight EPS, Tapered Roof Insulation is a value-engineered system that has been proven in new and reroof applications all over the country. This tapered roof insulation technology creates high thermal performance which improves interior comfort and reduces the energy costs of keeping a building comfortable.

MuleHide Poly ISO Flat insulations consist of a closed-cell polyisocyanurate foam core laminated to heavy, (non-asphaltic) glass fiber reinforced felt facers. The product insulations are compatible with all MuleHide membranes and accessories and are available in 20 and 25 psi densities. MuleHide Poly ISO insulation boards may be used for ballasted, mechanically attached and fully adhered single-ply roofing systems. Poly ISO insulation board may be installed over approved decks and substrates on new construction, tearoffs and recover (retrofit) projects. Rated for use in UL Class A and FM Class 1 assemblies.

MuleHide Poly ISO Tapered insulations consist of a closed-cell polyisocyanurate foam core laminated to heavy, (non-asphaltic) glass fiber reinforced felt facers. The product insulations are compatible with all MuleHide membranes and accessories and are available in 20 and 25 psi densities. MuleHide Poly ISO insulation boards may be used for ballasted, mechanically attached and fully adhered single-ply roofing systems. Poly ISO insulation board may be installed over approved decks and substrates on new construction, tearoffs and recover (retrofit) projects. Rated for use in UL Class A and FM Class 1 assemblies.

A 40-Mil composite consisting of 35-Mils of self-adhering rubberized asphalt laminated to a 5-Mil woven polypropylene film. A siliconized one-piece release liner prevents the material from bonding to itself in the roll and is easily removed for installation. F5 Air & Vapor Barrier is available in a 325 sq. ft. roll with dimensions of 39"x 100'. The factory-controlled thickness of the membrane ensures uniform barrier properties, and the woven polypropylene film increases strength and has a non-skid surface suitable for the bonding of subsequent layers.

FR-10 Fire retardant slipsheet is for use over combustible wood decks, or over certain EPS/XPS insulation. It can be used with PVC, EPDM, or TPO membranes assemblies to achieve specific class A and Class B fire resistance ratings

Shur-Gard MU Force HT is a self-adhered high-temp waterproofing underlayment for metal roof coverings and various other applications. Utilizing ADESO® dual-compound self-adhered technology, Shur-Gard MU Force HT features a polymer modified bitumen upper compound and a proprietary self-adhesive SBS (elastomeric) compound on the bottom. A split release film that protects the self-adhesive compound allows for easy application.

Shur-Gard MU Ultra HT is a self-adhered high-temp waterproofing underlayment for use under metal and various other roof coverings. The top surface is composed of a UV resistant high strength polyolefin composite film with anti-skid coating which is mated to a high-temp SBS (elastomeric) self-adhered compound. A siliconized split-release paper provides quick and accurate Shur-Gard MU Ultra HT installation.

Shur-Gard TU Force HT is a self-adhered, dual reinforced waterproofing underlayment designed for use in adhesive foam or mechanically fastened roof tile applications. Utilizing ADESO® dual-compound self-adhered technology, TU Force HT features a UV resistant polymer modified bitument plastomeric upper compound, and a proprietary self-adhesive SBS (elastromeric) compound on the bottom. A split release film that protects the self-adhesive compound allows for easy application.

Shur-Gard TU Ultra HT is a self-adhered waterproofing underlayment designed for use in adhesive foam or mechanically fastened roof tile applications. Utilizing ADESO dual-compound self-adhered technology, TU Ultra HT features a polymer modified bitumen upper compound and a proprietary self-adhesive SBS (elastomeric) compound on the bottom. A split release film that protects the self-adhesive compound allows for easy application.

F/G Base Sheet is manufactured from tough inorganic fiberglass mat then coated on both sides with weathering grade coating asphalt and then covered on top with white sand fines to prevent sticking in the roll. Meets ASTM D 4601-04 Type II.

Applied over the flat roofing deck or insulation as a base sheet by mechanical fasteners or hot asphalt before the application of roofing systems. This sheet is suitable for use as a vapor retarder, with a solid mopping of asphaltic material, under roof insulation or between multiple layers of insulation.

A fiberglass mat coated with an oxidized asphalt blend, which provide enhanced weathering and aging characteristics. G2 Base is designed as a base sheet for MuleHide torch applied modified roofing applications. It may also be used in built up roofing applications. It provides great tear and pull through resistance.

Shur-Gard #40 Base Sheet is manufactured from superior quality felt that is saturated with asphalt and then coated on both sides with weathering grade coating asphalt and then covered on top with mineral surface fines to prevent sticking in the roll. Meets ASTM 2626-04.

Applied over the flat roofing deck or insulation before the application of Built-Up Roofing systems.

MuleHide #421 Mod Bit Flashing Adhesive – Trowel Grade is a high quality formulation for use as a cold-applied bonding agent for SBS modified bitumen roof systems. Heavy, “trowel-grade" consistency makes this product ideal for flashing details, attachment of membrane to steep slopes and parapet walls and a variety of waterproofing repairs, especially at moving joints where its flexibility and elasticity make it superior to standard plastic cements. In addition, the formulation is non-destructive to asphalt based roofing membranes.

CCW-702LV is a Low-VOC solvent-based, high-tack adhesives specifically designed to promote maximum adhesion of MuleHide F5 Air and Vapor Barrier/Temporary Roof to approved substrates. These products are also used as a surface prep to promote adhesion of Helix® Low-Rise Adhesive. CCW-702LV is available in 5-gallon pails; a full pallet consists of 45 pails.

AeroWeb Low-VOC Contact Adhesive/Primer with its web-like spray pattern is a versatile option in a number of applications:

• Standard TPO and Standard EPDM on vertical & horizontal surfaces for warranties up to 30 years
• Adhering Fleece Back (vertical application only)
• Enhancing the bond between F5 Air & Vapor Barrier and various substrates
• Priming unexposed asphalt prior to applying Helix® Low-Rise Adhesive for insulation attachment

Used for single-side, wet, horizontal application of EPDM to acceptable HD wood fiberboard, plywood, OSB, DensDeck® Prime Roof Board or SECUROCK® Roof Board. Low-temperature restrictions apply.

A two-sided water based bonding adhesive used to adhere EPDM, Standard TPO, TPO Fleece Back and PVC Fleece Back membranes to approved surfaces. Can be used as a one-sided, wet lay-in adhesive with MuleHide Fleece Back membranes. Low-temperature restrictions apply.

FR Adhesive is a fire-resistant, water-based, fume-free EPDM bonding adhesive used with standard OSB or plywood inventory. It eliminates the need for commercial modular manufacturers to stock specialized roof decks to meet UL Class C roof deck requirements.

Designed to bond PVC membranes to a clean, dry horizontal surface as a one-sided wet lay-in adhesive with slopes up to 2:12. HydroBond® can be used with both smooth back and fleece backed PVC membranes. Can also be used as a contact adhesive for vertical applications, such as flashings.

CCW-702 is a solvent-based, high-tack adhesives specifically designed to promote maximum adhesion of MuleHide F5 Air and Vapor Barrier/Temporary Roof to approved substrates. These products are also used as a surface prep to promote adhesion of Helix® Low-Rise Adhesive. CCW-702 is available in 5-gallon pails; a full pallet consists of 45 pails.

A high strength solvent-based contact adhesive that allows quick bonding of EPDM membrane and cured flashings to various porous and non-porous substrates. May be used on both horizontal and vertical surfaces. Formulated for application with a 1⁄2" (13 mm) medium nap roller.

Used on EPDM membranes for splicing field sheets. Also used to splice uncured EPDM flashing material to cured EPDM membranes. Use White Splice Adhesive when a white (white-on-black)membrane is required. MuleHide Tape Primer must be used to prepare the membrane prior to the application of the adhesive. This product cannot be used on warranted projects.

A high strength solvent-based contact adhesive that allows bonding of MuleHide TPO membrane to various porous and non-porous substrates.

AeroWeb Low-VOC Contact Adhesive/Primer with its web-like spray pattern is a versatile option in a number of applications:

• Standard TPO and Standard EPDM on vertical & horizontal surfaces for warranties up to 30 years
• Adhering Fleece Back (vertical application only)
• Enhancing the bond between F5 Air & Vapor Barrier and various substrates
• Priming unexposed asphalt prior to applying Helix® Low-Rise Adhesive for insulation attachment

AeroWeb PVC Low-VOC Contact Adhesive with its web-like spray pattern is a versatile option in a number of applications:

• Adhering PVC bareback membranes to a variety of horizontal substrates and vertical walls

• Adhering Fleece Back membranes to vertical surfaces

AeroWeb PVC cannot be used with any KEE bareback membranes or on wood fiberboard.

A high-strength, solvent -based contact adhesive that bonds EPDM membranes to various porous and non-porous substrates.

This version meets requirements of California Rule 1168. A high strength solvent-based contact adhesive that allows bonding of EPDM and TPO to various porous and non-porous substrates. Specially formulated using a blend of VOC exempt and non-exempt solvents to be meet the < 250 g/L VOC content requirements of the OTC Model Rule for adhesives and sealants.

A high-strength solvent-based contact adhesive that allows bonding of EPDM and TPO to various porous and non-porous substrates. Specially formulated using a blend of VOC exempt and non-exempt solvents to meet the < 250 g/L VOC content requirements of the OTC Model Rule for adhesives and sealants.

A high strength solvent-based contact adhesive that allows bonding of PVC membranes to various porous and non-porous substrates. It is specially formulated using a blend of VOC-exempt and non-exempt solvents to be in compliance with the California Clean Air Act of 1988 (updated in 1997) and as further regulated by California's Air Quality Control Districts listing VOC limitations. Low VOC PVC Bonding Adhesive is used for bonding PVC flashings and membranes to a variety of substrates.

Low-VOC UN-TACK Adhesive Remover & Cleaner is designed to remove adhesives from a variety of surfaces, including metal, vinyl, plastic, rubber, glass and most fabrics. Low-VOC UN-TACK also helps to remove damaged and improperly installed insulation and other materials, including adhesives and contact cements. This product will help prepare surfaces for the application of Hardcast rolled sealants, butyl tapes and other adhesives, while also aiding in their removal.

PVC Un-Tack is designed to clean spray guns and hoses used to apply AeroWeb PVC. PVC Un-Tack can also be used to remove adhesives and primers from a variety of surfaces including single-ply membranes, accessories, metal, plastic, rubber, and glass. DO NOT use PVC UN-TACK for removal of AeroWeb Adhesive/Primer.

Helix® Max Low-Rise Adhesive is a low-rise, VOC-free, construction-grade, two-component polyurethane adhesive designed to bond MuleHide insulations and Fleece Back (TPO, PVC or PVC KEE) membranes to a variety of substrates.

Available in both 15 and 50 gallon drums.

Helix® Max Low-Rise Adhesive is a low-rise, VOC-free, construction-grade, two-component polyurethane adhesive designed to bond MuleHide insulations and Fleece Back (TPO, PVC or PVC KEE) membranes to a variety of substrates.

Each box contains 4 Dual Cartridges and static mixing tips.

Helix® Max Low-Rise Adhesive-Dual Tank (“Helix Max Adhesive") is a low-rise, construction-grade, two-component polyurethane adhesive that is designed to bond MuleHide's insulations and Fleece Back (TPO, PVC or PVC KEE) membranes to a variety of substrates. FM and other agency approvals

Self-contained tank set (A & B Components) includes guns, spray nozzles, 14" extension nozzle, and hoses in the A-side box.

Helix® Max Low-Rise Adhesive is a low-rise, VOC-free, construction-grade, two-component polyurethane adhesive designed to bond MuleHide insulations and Fleece Back (TPO, PVC or PVC KEE) membranes to a variety of substrates.

Comes in 5-Gallon Jugs (Set).

Tough and flexible, MuleHide #420 Mod Bit Adhesive – Brush Grade is a premium-quality, brush-grade, cold-applied bonding agent for use in installing SBS modified bitumen base sheets and SBS modified bitumen cap sheets. Fortified with high SBS content and reinforcing fibers, it delivers unsurpassed resiliency and durability. It is specially formulated for use with MuleHide self-adhering modified bitumen membranes.

• Can be used to install SBS modified bitumen base sheets and SBS modified bitumen cap sheets to a variety of substrates, including structural concrete roof decks, existing smooth-surfaced asphalt built-up roofs, approved roof insulations, and glass fiber base sheets.

• Can be used as an adhesive for APP sand back modified bitumen membranes.

• Bonds gravel or mineral granules to built-up roofing systems and modified bitumen cap sheets.

• Can be used in conventional build-up roofing systems.

MuleHide #421 Mod Bit Flashing Adhesive – Trowel Grade is a high quality formulation for use as a cold-applied bonding agent for SBS modified bitumen roof systems. Heavy, “trowel-grade" consistency makes this product ideal for flashing details, attachment of membrane to steep slopes and parapet walls and a variety of waterproofing repairs, especially at moving joints where its flexibility and elasticity make it superior to standard plastic cements. In addition, the formulation is non-destructive to asphalt based roofing membranes.

EclipsEdge is a three-piece snap-on fascia for single-ply applications. This product provides superior protection from wind and water penetration with economical pricing to maximize your profits. Our fast lead times and easy installation translate directly into decreased labor costs and enable you to move on to other projects more quickly.

EclipsEdge Extended MB is for BUR or Modified roofs. It protects against high wind events where longer face heights are needed, saving the building from costly damage. The design eliminates the stripping that is typical of other products, making EclipsEdge Extended MB fast and easy to install.

EclipsEdge MB is for BUR or modified roofs. Offers quick-to-ship convenience and economical pricing to simplify projects and maximize profits. Protecting against high wind events, saving the building from costly damage.The design eliminates the stripping that is typical of other products, making EclipsEdge MB fast and easy to install.

A 24-gauge galvanized steel sheet coated with a layer of 0.035" non-reinforced PVC flashing. PVC Coated Metal is cut into the appropriate width and used to fabricate metal drip edges or other roof perimeter edging profiles. PVC membrane may be welded directly to the coated metal edging, eliminating the need to strip in the metal with a separate piece of membrane.

A 24-gauge galvanized steel sheet coated with a layer of 0.035" non-reinforced TPO flashing. TPO Coated Metal is cut into the appropriate width and used to fabricate metal drip edges or other roof perimeter edging profiles. TPO membrane may be welded directly to the coated metal edging on Fully Adhered TPO roof systems, eliminating the need to strip in the metal with a separate piece of membrane.

Drip Edge provides maximum water flow from roof decks while providing an architectural, visually-attractive termination. It is specifically designed to simplify the installation process and save costs. It is available in convenient 12' lengths with pre-slotted fastening holes.

Drip Edge MB is specifically designed for use with APP and SBS torch-applied assemblies. It provides maximum water flow from roof decks while providing architectural, visually-attractive termination. It is specifically designed to simplify the installation process and save costs. It is available in convenient 12' lengths with pre-slotted fastening holes. 

Gravel Stop offers quick-to-ship convenience and economical pricing to simplify projects and maximize profits. Its concealed splice plate design prevents migration under the fascia panels and provides proper spacing for thermal movement of the fascia material. Gravel Stop is specifically designed to simplify the installation process and further save costs.  It is available in convenient 12' lengths with pre-slotted fastening holes.

Skirted Drip Edge is a factory-fabricated coated metal edge system used to terminate at the perimeter of PVC or TPO. This edge comes with a factory applied, wide PVC or TPO flashing strip to help save labor installation costs in the field. Skirted Drip Edge available with custom face sizes is an economical solution for many conditions such as continuous edge drainage with or without a gutter condition.

1 3/4" Fascia Cover is for all types of roof systems. This version, made from formed .063" aluminum, comes in convenient 12' lengths with pre-slotted holes for quicker installation and lower labor costs.

2-Piece Snap-On Compression features a snap-on cover that eliminates crimping, substantially reducing installation time on single-ply roofs. Dual attachment points on both the face and roof deck allow for added flexibility when accommodating roof irregularities. With no exposed fasteners and no unsightly cover plates, 2-Piece Snap-On Compression will complement the buildings aesthetics, while also being fast and easy to install.

2-Piece Snap-On Compression MB features a snap-on cover that eliminates crimping, substantially reducing installation time on BUR or modified roofs. Dual attachment points on both the face and roof deck allow for added flexibility when accommodating roof irregularities. With no exposed fasteners and no unsightly cover plates, 2-Piece Snap-On Compression MB will complement the buildings aesthetics, while also being fast and easy to install.

4" Fascia Cover is a versatile and affordable roof termination system that is well-suited to both low and steep sloped roofing applications. An aluminum bar with pre-punched, slotted fastener holes securely terminates the membrane. 4" Fascia Cover design eliminates the need for stripping-in or heat welding, and the convenient 12' length enables fast and easy installation.


ES-1 Calculator

Coping offers quick-to-ship convenience and economical pricing to simplify projects and maximize profits. The product is ANSI/SPRI/FM 4435/ES-1 tested and is manufactured in 12' lengths with fasteners provided for quicker installation and lower costs.


ES-1 Calculator

Counterflashing provides a watertight termination at the leading edge of the roofing material. Available in 1 piece reglet, 1-piece surface mounted or 2-piece reglet. - 1 piece reglet is a great option when a receiver is not required. - 1-piece surface mounted is a great option when a receiver and a joint reglet are not required. - 2-piece reglet is easily installed by hooking and rotating the flashing to snap into the receiver. It provides a watertight termination at the leading edge of the roofing material. This counter flashing can be taken apart for easy roof repairs.

ES-1 Calculator

One Fascia offers quick-to-ship convenience and economical pricing to simplify projects and maximize profits. One Fascia for single-ply roofs protects against high wind events, saving the building from costly damage. The design eliminates the stripping in typical of other products, making One Edge Fascia fast and easy to install.

Snap Coping is the perfect solution for parapet conditions where the slope must be created. It has a full snap-on design with 20-gauge, galvanized steel anchor clips and factory-applied stainless steel springs that ensure long-term positive attachment, bringing extra stability to the roof edge system. In addition, the snap-on design facilitates fast and easy installation. Snap Coping is custom fabricated in sizes to meet specific job requirements.

ES-1 Calculator

Downspouts are available in a variety of standard sizes, or it can be fabricated to meet specific job requirements. Downspouts are manufactured with simple connection configurations and include three attachment straps per 12' section, which enables fast and easy installation.

Gutters are specifically engineered and tested to meet the requirements of the ANSI/SPRI GT-1 Standard for Gutter Systems used with Low-Slope Roofs. The gutter system incorporates a 1-in. wide, 2-piece extruded aluminum internal gutter bracket for strength and support. The bracket also reduces telegraphing of the metal due to expansion and contraction of the gutter during temperature changes.


Gutter Calculator

Custom-designed Scuppers and Collector Boxes that meet the performance requirements of architects and contractors. Their unique design provides maximum security and performance to protect against leaks, and is a decorative and functional means of water control.

Traditionally, single-ply roofing is one-size-does-it all. Yet more and more modular manufacturers and dealers are reaping the benefits of MuleHide Professional Roofing Systems custom sizes to fit modular structures or master rolls with modular industry sheet sizes. We also offer white on black EPDM that reflects the sunlight & cools the building interior - leading to lower BTU usage and energy costs. Use with Acrylic Water Base Bonding Adhesive - fast installation keeps factory lines moving. Fully-adhered application is required

A thermoplastic polyolefin based for superior strength and weatherability. More product on the top of the scrim where you need it most, one of the thickest top plies in the industry. Our reinforced membranes offer watertight integrity you can count on. MuleHide TPO is CRRC rated and Energy Star listed. TPO has the weathering capability of EPDM with the superior seam strength of heat weldable membranes.

Butyl Seal Tape may be used on to seal EPDM membranes in certain details. It adheres to plastics, concrete and metals. This product may be used to repair gutters, chimney flashings, and metal roofs on mobile homes and transport vehicles. May be used as a substitute for water Cut-Off Mastic in certain details as noted in the published MuleHide details.

FR Adhesive is a fire-resistant, water-based, fume-free EPDM bonding adhesive used with standard OSB or plywood inventory. It eliminates the need for commercial modular manufacturers to stock specialized roof decks to meet UL Class C roof deck requirements.

MuleHide Mate-Line™ Tape was specifically developed to seal the EPDM membrane roof system at the junctions of multiple modular units. MuleHide Mate- Line™ Tapes shall be used in conjunction with the MuleHide Tape Primer to strip gravel stops, drip aprons, or seams.

Furnish and install the Modular Pipe Boot at all points where any projection penetrates the roof system, and is less than 3" in diameter.

MuleHide Self-Bridging Mate-Line™ was specifically developed to seal the EPDM membrane roof system at the junctions of multiple modular units. MuleHide Self-Bridging Mate-Line™ is used in conjunction with the MuleHide Tape Primer to span the gap between modular units.

Curb Wraps provide an efficient means to flash a curb with EPDM materials. Curb Wrap is pre-cut to a 20" width and has 6" In-Seam Tape pre-applied. Production time can be substantially reduces with this labor saving product. Available in black. Also available in 20" Fully pre-taped backing in Black and Gray, which can also be used to make easy repairs on adhered EPDM Roofs.

Ideal for installing inside and outside corners. Consists of .060 inch (1.5-mm) thick uncured EPDM flashing material laminated to cured butyl rubber tape and rolled onto a poly release liner providing .090 mils (2.25-mm) of total thickness. This product requires the use of Tape Primer or Low-VOC Tape Primer.

Used to seal field splice joints or a horizontal-to-vertical field seam transition. 40 mil (1 mm) thick uncured EPDM flashing material laminated to cured butyl rubber tape and rolled onto a poly release liner for a total thickness of 70 mils (1.75 mm). This product requires the use of Tape Primer or Low VOC Tape Primer.

A 24-gauge galvanized steel sheet coated with a layer of 0.035" non-reinforced PVC flashing. PVC Coated Metal is cut into the appropriate width and used to fabricate metal drip edges or other roof perimeter edging profiles. PVC membrane may be welded directly to the coated metal edging, eliminating the need to strip in the metal with a separate piece of membrane.

MuleHide PVC Inside Corners are uniform in shape and size and provide watertightness at inside corners formed by PVC coated metal and/or PVC flashing membrane. Provides a neat, finished look to building corners, curbs and parapet flashings with no cutting required.

Used for sealing joints of MuleHide PVC Coated Metal, drain details, field flashing pipes and other details where reinforced membrane or the used of pre-molded accessories are not feasible.

Are uniform in shape and size and provide water tightness at outside corners formed by PVC coated metal and/or PVC flashing membrane. Provides a neat, finished look to building corners, curbs and parapet flashings with no cutting required.

Used to seal step-offs at splice intersections. Installation is mandatory on all 60-mil and 80-mil PVC systems and on 45-mil systems where step-offs have not been properly sealed.

Uniform in shape and size and provide watertightness at corners formed by PVC coated metal and/or PVC flashing membrane. Provides a neat, finished look to building corners, curbs and parapet flashings with no cutting or stretching required.

The Decorative Rib (available in TPO or PVC versions) is secured to a MuleHide Fully Adhered roofing membrane to simulate the appearance of a standing seam metal roofing system.

Primarily used to seal details where field fabrication is necessary, such as drain details, pipe flashings, pitch pocket flashings, seaming joints of the MuleHide TPO Coated Metal and any place where reinforced membrane is not practical.

A 24-gauge galvanized steel sheet coated with a layer of 0.035" non-reinforced TPO flashing. TPO Coated Metal is cut into the appropriate width and used to fabricate metal drip edges or other roof perimeter edging profiles. TPO membrane may be welded directly to the coated metal edging on Fully Adhered TPO roof systems, eliminating the need to strip in the metal with a separate piece of membrane.

Uniform in shape and size and provide watertightness at inside corners formed by TPO coated metal and/or TPO flashing membrane. Provides a neat, finished look to building corners, curbs and parapet flashings with no cutting required.

Uniform in shape and size and provide water tightness at outside corners formed by TPO coated metal and/or TPO flashing membrane. Provides a neat, finished look to building corners, curbs and parapet flashings with no cutting required.

Used to seal step-offs at splice intersections. Installation is mandatory on all 60 mil and 80 mil TPO systems and on 45 mil systems where step-offs have not been properly sealed.

Uniform in shape and size and provide watertightness at corners formed by TPO coated metal and/or TPO flashing membrane. Provides a neat, finished look to building corners, curbs and parapet flashings with no cutting or stretching required.

May be used in conjunction with the MuleHide Tape Primer to flash inside and outside corners, pipes, pitch pockets or other penetrations that require the flashing to be molded or conform to an irregular shape. Not permitted for use in flashing gravel stops, drip aprons or stripping seams or batten bars. This product requires the use of Tape Primer or Low-VOC Tape Primer.

Ideal for sealing irregular, hard to flash penetrations through the membrane. Prefabricated pockets consisting of a 2" (50-mm) wide plastic support strip with attached Uncured EPDM Flashing Tape. This product requires the use of Tape Primer or Low-VOC Tape Primer. Available in Black or White.

Uncured EPDM Flashing Membrane is a 60-mil thick, self-curing membrane used as a pliable flashing that can be formed to seal pipes, inside and outside corners, and other projections that cannot be sealed with cured EPDM membrane. Consult drawings for installation details.

Prefabricated Pitch Pans deliver a watertight seal around rooftop protrusions.

Accommodates single pipe sizes from 1" to 6" in diameter. Conical-shaped steps securely seal all single pipe penetrations. The large, double-thick, molded rib at the top of each step offers superior tear resistance and reinforcement, as well as a cutting guide. This product requires the use of Tape Primer or Low-VOC Tape Primer.

Prefabricated two-way, or static, vents allow proper ventilation of attic spaces below PVC membranes. The reinforced membrane flange allows for quick installation by centering vent over opening and welding to the field membrane.

Interlocking, two-piece prefabricated pockets of non-reinforced PVC material used to seal pipe clusters or other irregular shaped penetrations. Pockets length can be adjusted from 7-1/2" to 11-1/2" by following the pre-molded cutting lines.

An injection molded, pre-formed flashing for single pipe penetrations made of MuleHide non-reinforced PVC material. Designed to add ease to the installation process while offering increased watertight security and improved aesthetics.

Contains a split (cut) and overlap tab that allows the pipe-boot to be opened and wrapped around a round pipe with an obstruction. Such obstructions prevent the use of a standard pre-molded pipe boot. Made of 60 mil reinforced PVC membrane for pipes 1" to 6" in diameter.

PVC Square Tubing Wraps are fabricated square penetration flashings made of white, gray or tan 60 mil standard reinforced PVC membrane. Overall height of the flashing is 11 inches. A split (cut) and overlap tab are incorporated into these parts to allow the flashing to be opened and wrapped around a square penetration with an obstruction. The PVC Square Tubing Wraps are primarily used to seal details where field fabrication is necessary, such as drain details, pipe flashings and pitch pocket flashings.

Prefabricated PVC flashing for hot stacks, dryer vents or static attic vents that come complete with painted metal sleeve and vent caps. Large target base patch allows for quick installation by simply screwing the metal sleeve to the deck and then welding the target base to the field membrane. This product cannot be used on warranted projects. For residential use only.

ShapeShift® Kits put everything needed to create pitch pans in one convenient package. The “grab-and-go" kits are available in two sizes to accommodate jobs of various sizes.

Large kits contain 16 ShapeShift corner sections, 16 ShapeShift straight sections, 3 - 2 liter pouches of MP Liquid Sealant in white and three cartridges of JTS 1 joint and termination sealant in white. Large kits create four 7- by 7-inch pitch pans.

Small kits contain 16 ShapeShift corner sections, 1 - 2 liter pouch of MP Liquid Sealant in white and two cartridges of JTS 1 in white. Small kits create four 4- by 4-inch pitch pans.

ShapeShift kits can be used to create pitch pans for acrylic-coated, smooth modified bitumen, and smooth built-up roofing systems.

ShapeShift® pitch pans consist of straight and outside corner sections that snap together to create an endless number of pitch pan sizes to seal around roof projections. The radius corner pieces measure approximately 2" x 2". The straight sections measure approximately 3" long. The high-strength polymer pieces have a 2-1/2" base flange with a 1-3/4" high side. The pieces snap together with interlocking joints. The smallest pitch pan possible is 4" x 4" (4 corner pieces). The maximum size is unlimited. ShapeShift® pitch pans are approved for installation on MuleHide warranted projects when installed on vertical surfaces if filled with JTS 1 sealant instead of MP Liquid Sealant.

Prefabricated two-way, or static, vents allow proper ventilation of attic spaces below TPO membranes. The reinforced membrane flange allows for quick installation by centering vent over opening and welding to the field membrane.

Interlocking, two-piece prefabricated pockets of non-reinforced TPO material used to seal pipe clusters or other irregular shaped penetrations. Pockets length can be adjusted from 7-1/2" to 11-1/2" by following the pre-molded cutting lines.

Designed as an economical flashing for single pipe penetrations on MuleHide TPO Membrane roof systems. TPO Pipe Seals can be used wherever the TPO Pipe Seals may be slipped over the top of the pipe.

Contains a split (cut) and overlap tab that allows the pipe boot to be opened and wrapped around a round pipe with an obstruction. Such obstructions prevent the use of a standard pre-molded pipe boot.

TPO Square Tubing Wraps are fabricated square penetration flashings made of 60 mil standard reinforced TPO membrane and are available in 8 colors. Overall height of the flashing is 11 inches. A split (cut) and overlap tab are incorporated into these parts to allow the flashing to be opened and wrapped around a square penetration with an obstruction. The TPO Square Tubing Wraps are primarily used to seal details where field fabrication is necessary, such as drain details, pipe flashings and pitch pocket flashings.

Designed as an economical flashing for single pipe penetrations on MuleHide TPO Membrane roof systems. TPO Universal Conical Boot can be used wherever the TPO Universal Conical Boot may be slipped over the top of the pipe.

Prefabricated TPO flashing for hot stacks, dryer vents or static attic vents that come complete with painted metal sleeve and vent caps. Large target base patch allows for quick installation by simply screwing the metal sleeve to the deck and then welding the target base to the field membrane. This product cannot be used on warranted projects. For residential use only.

Detec TruGround Conductive Primer makes effective electronic leak detection (ELD) testing of conventional roof assemblies fast and easy, helping ensure that a roofing system is watertight and free of breaches, holes, and seam voids.

A low-VOC product designed for one-step cleaning and priming of EPDM and TPO surfaces prior to the application of In-Seam Tapes and other taped products.

Used to clean both new and in-service EPDM, TPO, PVC and PVC KEE membranes prior to the seaming process. This cleaner helps to loosen and remove dirt and other contaminants from the membrane surface and leaves a suitable surface for welding or the subsequent application of Tape Primer. . Low-VOC Membrane Cleaner meets California & Utah VOC regulations.

Low-VOC PVC Step 1 Activator is a high-strength, solvent-based activator that allows PVC Pressure-Sensitive (PS) Cover Strip to be bonded to MuleHide PVC or KEE HP membranes.

Low-VOC PVC Step 2 Primer is a high-solids, polymer-base splice primer. This product is applied to PVC and KEE HP membrnaes to improve the adhesion of PVC Pressure-Sensitive (PS) Cover Strip.

Si TPO Primer is a primer used to promote adhesion with 100% Silicone Roof Coating to new and aged TPO roofing membranes. Si TPO Primer is manufactured from fast-evaporating solvents and adhesive resins. Primer has a blue color to allow applicator to better gauge application rates.

A solvent-based product designed for one-step cleaning and priming of EPDM surfaces to be bonded with In-Seam Tapes, Uncured Flashing Tapes, Cured Cover Tapes and Pre-Taped membranes.

A solvent-based product designed for one-step cleaning and priming of TPO surfaces to be bonded with In-Seam Tapes, Uncured Flashing Tapes, Cured Cover Tapes, and Pre-Taped membranes. It is specially formulated using a blend of VOC exempt and non-exempt solvents to meet the < 250 g/L VOC content requirements of the OTC Model Rule for adhesives and sealants.

Used to clean in-service EPDM membrane that has been exposed to the weather and clean TPO membrane prior to the welding process. Helps to loosen and remove dirt and other contaminants from the surface of the EPDM and TPO membranes and leaves a suitable surface for welding or the subsequent application of Tape Primer.

10" wide TPO Pressure-Sensitive RUSS is used in place of narrow width sheets to secure membrane in the perimeter area of the roof. Allows field membrane to be utilized over the entire roof area. Ideal when multiple perimeter sheets or non-standard perimeter spacings are required. This product requires the use of TPO Tape Primer or Low VOC Tape Primer.

Used in conjunction with MuleHide 2.4" seam plates and MuleHide HDP fasteners as securement of the EPDM membranes at the base of parapet walls and curbs. Installed beneath the EPDM field sheet and used as an alternate method to using the MuleHide All Purpose Bar. This product requires the use of Tape Primer or Low VOC Tape Primer.

May be used with TPO and should only be installed on horizontal surfaces using an appropriate MuleHide fastener below the roof membrane providing additional securement at angle changes. RUSS is secured with MuleHide EHD (#15) or HDP (#14) Fasteners and MuleHide 2.4" Seam Plates. This product requires the use of TPO Tape Primer or Low VOC Tape Primer.

Available in a 9" width with two strips of pre-applied In-Seam Tape. Used to attach EPDM membranes horizontally in the field of the roof on mechanically fastened systems. This product requires the use of Tape Primer or Low VOC Tape Primer.

A nominal 60-mil, cured EPDM membrane strip laminated to nominal 30-mil cured butyl rubber tape and rolled onto a release liner, for a total nominal thickness of 90-mil. Commonly used to strip in metal edging.This product requires the use of Tape Primer or Low-VOC Tape Primer.

A black or white, butyl rubber-based adhesive in tape form. Formulated to provide high green strength in both shear and peel. May be used on ballasted, mechanically attached and fully adhered EPDM roofing systems. This product requires the use of Tape Primer or Low VOC Tape Primer.

Available in white, gray, and tan, PVC Reinforced Coverstrip is used for stripping in rows of fasteners and plates and covering the butt joints of Sure-Flex PVC and FleeceBACK® PVC membranes. This product's smooth surface allows a total surface fusion weld over a wide temperature range, facilitating a consistent, watertight roof system. PVC Reinforced Coverstrip cannot be used to flash corners, pipes, t-joints, any angled metal flanges such as gravel stops, or other canted metal edgings.

Non-reinforced thermoplastic polyvinyl chloride-based membrane used for stripping in PVC or PVC KEE HP coated metal roof edging.

Coverstrip is used for stripping in rows of fasteners and plates and covering the butt joints of PVC and FleeceBACK PVC membranes. This product's smooth surface allows a total surface fusion weld over a wide temperature range, facilitating a consistent, watertight roof system.

A nominal 35-mil non-reinforced KEE HP flashing laminated to a nominal 35-mil, fully cured, pressure-sensitive, synthetic rubber adhesive. Used to strip in flat metal edgings (e.g. drip edge).

Seal-Fast® Tape may be used on a wide variety of surfaces including difficult roof materials such as : EPDM, TPO, most PVC, CSPE/Hypalon, CPE, SBS, APP modified, asphalt BURs, coal tar BURs, all metal roofs, tiles, shingle, aluminum, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry, OSB, etc.. This product may be used to repair gutters, chimney flashings, and metal roofs on mobile homes and transport vehicles. Seal-Fast® Tape makes a permanent watertight seal. Can be installed in temperatures down to -20oF (with our Seal-Fast® Primer). Also available in Seal-Fast Plus, Aluminum, Double Stick and Fabric tapes.

Used as cover strips over end lap joints of Fleece Back Membrane. TPO flashing strips may also be used to flash over TPO Coated Metal joints and to strip-in coated metal flanges. May be used for general repairs where reinforced material is required.

Intended to strip in flat metal flanges (i.e. drip edge or self-flashing curb flanges) or rows of fasteners and plates. TPO Cover Strip cannot be used for flashing corners, pipes, T-joints or butt joints on TPO Fleece Back Membrane or any angled metal flanges such as gravel stops or other canted metal edgings. This product requires the use of TPO Tape Primer or Low VOC Tape Primer.

May be used in conjunction with the MuleHide Tape Primer to flash inside and outside corners, pipes, pitch pockets or other penetrations that require the flashing to be molded or conform to an irregular shape. Not permitted for use in flashing gravel stops, drip aprons or stripping seams or batten bars. This product requires the use of Tape Primer or Low-VOC Tape Primer.

Designed to protect the membrane in areas exposed to repetitive foot traffic. MuleHide requires walkways to be installed at all traffic concentration points, such as roof hatches, access door, rooftop ladders, etc. regardless of traffic frequency. Walkways are also required if regular maintenance (once a month or more) is necessary to service rooftop equipment.

A nominal 6 ounce per square yard (140 grams per square meter) UV resistant polypropylene needle punched fabric. Can be used above the membrane as a slipsheet for crushed stone or pavers or below the membrane as a minimum underlayment mat for mechanically attached or ballasted system applications.

PVC Walkway Roll incorporates an aggressive, non-slip, herringbone tread pattern of polyester reinforced PVC material that offers excellent tear and puncture resistance.

An environmentally friendly product that provides superior protection to the underlying membrane. Features a resilient, shock-absorbing, weather-resistant traffic surface. Pavers lock together to provide multi-directional drainage patterns eliminating the need for protective mats. Consists of 90% post-consumer recycled content.

TPO Walkway Roll incorporates an aggressive, non-slip, diamond plate tread pattern of polyester reinforced TPO material that offers excellent tear and puncture resistance. Walkway Rolls are trimmed in safety yellow along the length of the sheet to better define the walkway area. The yellow edges are smooth without safety lugs to allow for easier welding.

Yellow PS Safety Warning Strip is intended for use on EPDM,TPO and PVC roofing systems to provide a visual warning of an impending hazard (i.e. roof edge, deep drain sump, skylight, etc.) It is meant to be beneficial when maintenance personnel are frequently on the roof. Yellow Warning Strip cannot be used for flashings or as a coverstrip.

Aluminator Retrofit Roof Drain with MaxxFlo Seal is designed to quickly address the need to replace existing roof drains in a re-roofing application. Durability is assured through the use of heavy duty (0.125") aluminum. The exclusive MaxxFlo mechanical seal offers superior protection against water backup. Available with a variety of flange options (plain aluminum, TPO clad, PVC clad and asphalt coated) to accommodate most roofing systems.

Aluminum Retrofit Roof Drain with Sealant Tape allows for quick replacement of existing roof drains. Drain body is constructed from 0.125" aluminum for durability. Sealant Tape protects against water backup by expanding up to 4 times its original thickness. Available with two types of strainers (plastic and aluminum) and a variety of flange options (plain aluminum, TPO clad, PVC clad and asphalt coated) to accommodate most roofing systems.

Cast Iron New Installation Roof Drain Kit allows for quick installation of new roof drains or replacement of existing roof drains. Kit contains all the components needed and is adaptable to most generic single ply membranes and conventional built-up roofing. Can be used on steel, wood, pre-cast concrete or gypsum roof decks.

Copper Retrofit Roof Drain with Sealant Tape allows for quick replacement of existing roof drains. Drain body is constructed from heavy duty copper for durability. Sealant Tape protects against water backup by expanding up to 4 times its original thickness. Available with a variety of flange options (plaincopper, TPO clad, PVC clad and asphalt coated) to accommodate most roofing systems.

The prefabricated drop tube scupper with heat-welded seams is an excellent alternative and solution for a through roof soffit drain and downspout tie in. With an easy heat-weld flange for quick and watertight application. For residential use only.

PVC New Installation Roof Drain Kit allows for quick installation of new roof drains or replacement of existing roof drains. Kit contains all the components needed and is adaptable to most generic single ply membranes and conventional built-up roofing. Can be used on steel, wood, pre-cast concrete or gypsum roof decks.

The prefabricated membrane coated scupper insert detail with heat welded seams is a superior detail to the galvanized scupper sleeve and bonding adhesive alternative.

The prefabricated drop tube scupper with heat-welded seams is an excellent alternative and solution for a through roof soffit drain and downspout tie in. With an easy heat-weld flange for quick and watertight application. For residential use only.

The prefabricated membrane coated scupper insert detail with heat welded seams is a superior detail to the galvanized scupper sleeve and bonding adhesive alternative.