MasterFormat: 2020
Download this Cabinet and Drawer Hardware Specification for   WORD | WORD-Canadian | WP | RTF | TEXT
Find over 500 more construction specifications | Arcat.com
         
Salice America Inc. Cabinet and Drawer Hardware
 
         
SECTION 06 41 20
 
         
CABINET AND DRAWER HARDWARE
 
         
 
         
Copyright 2021 - 2021 ARCAT, Inc. - All rights reserved

          ** NOTE TO SPECIFIER ** Salice America Inc.; Cabinet and Door Hardware.
This section is based on the products of Salice America Inc., which is located at:
2123 Crown Centre Dr.
Charlotte, NC 28227
Toll Free Tel: 800-222-9652
Tel: 704-841-7810
Fax: 704-841-7808
Email: request info
Web: http://www.saliceamerica.com
[ Click Here ] for additional information.
Salice holds a well-established position worldwide by virtue of its natural talent for innovation, careful attention to quality, efficiency of customer service, and reliability earned during more than 90 years of experience. Salice is one of the most prestigious brands among the small, medium-sized, and large companies in the furniture industry.
 
          PART 1GENERAL
 
          1.1SECTION INCLUDES
          ** NOTE TO SPECIFIER ** Delete items below not required for project.
 
          A.Hinges.
 
          B.Runners and space organizers.
 
          C.Lift Systems and Systems for Fall Flaps:
 
          D.Furniture accessories.
 
          E.Sliding systems.
 
          F.Dampers and release devices.
 
          1.2RELATED SECTIONS
          ** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
 
          A.Section 06 40 00 - Architectural Woodwork.
 
          B.Section 06 41 14 - Plastic Laminate Faced Architectural Cabinets.
 
          C.Section 06 41 20 - Cabinet/Drawer Hardware*.
 
          D.Section 12 30 00 - Casework.
 
          E.Section 12 51 83 - Custom Office Furniture.
 
          1.3REFERENCES
          ** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
 
          A.American National Standards Institute (ANSI):
          1.ANSI/BHMA A156.9 - American National Standard for Cabinet Hardware.
          2.ANSI Grade 1.
 
          1.4SUBMITTALS
 
          A.Submit under provisions of Section 01 30 00 - Administrative Requirements.
 
          B.Product Data:
          1.Manufacturer's data sheets on each product to be used.
          2.Preparation instructions and recommendations.
          3.Storage and handling requirements and recommendations.
          4.Typical installation methods.
          ** NOTE TO SPECIFIER ** Delete if not applicable to product type.
 
          C.Verification Samples: Two representative units of each type, size, pattern, and color.
 
          D.Shop Drawings: Include details of materials, construction, and finish. Include relationship with adjacent construction.
 
          1.5QUALITY ASSURANCE
 
          A.Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with a minimum five years documented experience.
 
          B.Installer Qualifications: Company specializing in performing Work of this section with minimum two years documented experience with projects of similar scope and complexity.
 
          C.Source Limitations: Provide each type of product from a single manufacturing source to ensure uniformity.
          ** NOTE TO SPECIFIER ** Include mock-up if the project size or quality warrant the expense. The following is one example of how a mock-up on might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.
 
          D.Mock-Up: Construct a mock-up with actual materials in sufficient time for Architect's review and to not delay construction progress. Locate mock-up as acceptable to Architect and provide temporary foundations and support.
          1.Intent of mock-up is to demonstrate quality of workmanship and visual appearance.
          2.If mock-up is not acceptable, rebuild mock-up until satisfactory results are achieved.
          3.Retain mock-up during construction as a standard for comparison with completed work.
          4.Do not alter or remove mock-up until work is completed or removal is authorized.
 
          1.6PRE-INSTALLATION CONFERENCE
 
          A.Convene a conference approximately two weeks before scheduled commencement of the Work. Attendees shall include Architect, Contractor and trades involved. Agenda shall include schedule, responsibilities, critical path items and approvals.
 
          1.7DELIVERY, STORAGE, AND HANDLING
 
          A.Store and handle in strict compliance with manufacturer's written instructions and recommendations.
 
          B.Protect from damage due to weather, excessive temperature, and construction operations.
 
          1.8PROJECT CONDITIONS
 
          A.Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.
 
          1.9WARRANTY
 
          A.Manufacturer's standard limited warranty unless indicated otherwise.
 
          PART 2PRODUCTS
 
          2.1MANUFACTURERS
 
          A.Acceptable Manufacturer: Salice America Inc., which is located at: 2123 Crown Centre Dr.; Charlotte, NC 28227; Toll Free Tel: 800-222-9652; Tel: 704-841-7810; Fax: 704-841-7808; Email: request info; Web: http://www.saliceamerica.com
          ** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
 
          B.Substitutions: Not permitted.
 
          C.Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.
          ** NOTE TO SPECIFIER ** Delete article if not required or delete paragraphs not required.
 
          2.2HINGES
 
          A.Integrated Soft-Close Hinges with Adjustment Switch:
          ** NOTE TO SPECIFIER ** Delete series and finish options not required.
          1.Series CU Silentia: "Face-Frame1/2 2 cam adjustment.
          a.Stamped steel.
          b.Door Thickness: 9/16 to 7/8 inches (14 to 22 mm).
          c.Cup Diameter: 1-3/8 inch (35 mm). Cup Depth: 7/16 inches (11 mm).
          d.Opening: 106 degrees.
          e.Finish: Nickel.
          f.Finish: Titanium.
          2.Series CU Silentia: "Face-Frame1/2 3 cam adjustment.
          a.Stamped steel.
          b.Door Thickness: 9/16 to 7/8 inches (14 to 22 mm).
          c.Cup Diameter: 1-3/8 inch (35 mm). Cup Depth: 7/16 inches (11 mm).
          d.Opening: 106 degrees.
          e.Edgemount: Front tabs only.
          f.Finish: Nickel.
          g.Finish: Titanium.
          h.Six way adjustable by automatic cams.
          ** NOTE TO SPECIFIER ** Delete accessories and color options not required.
          3.Accessories:
          a.Cover Caps: For partial overlay Silentia face frame hinges. Compatible with overlays from 1/2 to 3/4 inch (13 to 19 mm). Material: Nylon.
          1)Personalize with Custom Logo:
          a)Logo: As supplied by the Architect.
          2)Color: White.
          3)Color: Grey.
          4)Color: Titanium.
          b.Cover Caps: For full overlay Silentia face frame hinges. Compatible with overlays from 1 to 1-3/8 inches (25 to 35 mm). Material: Nylon.
          1)Personalize with Custom Logo:
          a)Logo: As supplied by the Architect.
          2)Color: White.
          3)Color: Grey.
          4)Color: Titanium.
          c.Angle Reduction Clip: Clips on and limits opening to 86 degrees. For Silentia face frame hinges. Compatible with all overlays.
 
          B.Push Opening Hinges for Handle-Less Doors
          ** NOTE TO SPECIFIER ** Delete series options and device options not required.
          1.Push Series 200 Hinges: An integrated system of hinges developed to provide a solution to any situation involving concealed hinges. Bright nickel plated 1-3/8 inch (35 mm) diameter steel cup and arm.
          a.Adjustments:
          1)Compensating Side Adjustment: Minus 0.06 to 0.18 inches (minus 1.5 to 4.5 mm).
          2)Height Adjustment: Plus or minus 0.08 inches (plus or minus 2 mm).
          3)Depth Adjustment: Series 200 mounting Plates. 0.11 inches (2.8 mm).
          4)Depth Adjustment: Domi Snap-On mounting Plates: from 0.02 to 0.11 inches (0.5 to 2.8 mm).
          b.Anti-sliding safety stop.
          c.For Doors up to 1-1/4 inches (32 mm) Thick: Hinges are reverse-sprung so door self-opens when release device is activated.
          1)Opening: 94 degrees.
          2)Opening: 110 degrees.
          d.For Doors up to 1-1/8 inches (28 mm) thick: Hinges are reverse-sprung so door self-opens when release device is activated.
          1)Opening: 155 degrees.
          e.Push Series 200 Complementary Hinges:
          1)Hinges for doors with positive angled assembly.
          2)Crampon Hinges. For cabinet sides with 1-7/16 x 1-1/4 (37 x 32 mm) drilling.
          a)Opening: 94 degrees.
          3)Crampon Hinges. For smaller spaces with 19/32 x 1-1/4 inches (15 x 32 mm) drilling.
          a)Opening: 94 degrees.
          2.Push Hinges for Metal Profiles:
          a.Opening: 105 degrees. Hinges are reverse-sprung so door self-opens when release device is activated.
          b.Hinges for Doors with Positive Angled Assembly:
          1)Opening: 105 degrees.
          c.Crampon Hinges. For cabinet sides with 1-7/16 x 1-1/4 (37 x 32 mm) drilling.
          1)Opening: 105 degrees.
          d.Crampon Hinges. For smaller spaces with 19/32 x 1-1/4 inches (15 x 32 mm) drilling.
          1)Opening: 105 degrees.
          3.Push Series B hinges. For use on glass doors and mirrors.
          a.Adjustments:
          1)Compensating Side Adjustment: Minus 0.06 to 0.18 inches (minus 1.5 to 4.5 mm).
          2)Height Adjustment: Plus or minus 0.08 inches (plus or minus 2 mm).
          3)Depth Adjustment: With Series 200 mounting plates. 0.11 inches (2.8 mm).
          4)Depth Adjustment: With Domi snap-on mounting plates from 0.02 to - 0.11 inches (0.5 to 2.8 mm).
          b.Mounting Adhesive Torsion Load: 118 ft-lbs (160 Nm). When plate is fixed to the glass.
          c.Opening: 110 degrees.
          4.Push Series B hinges. For use on wood doors.
          a.Adjustments:
          1)Compensating Side Adjustment: Minus 0.06 to 0.18 inches (minus 1.5 to 4.5 mm).
          2)Height Adjustment: Plus or minus 0.08 inches (plus or minus 2 mm).
          3)Depth Adjustment: With Series 200 mounting plates. 0.11 inches (2.8 mm).
          4)Depth Adjustment: With Domi snap-on mounting plates from 0.02 to - 0.11 inches (0.5 to 2.8 mm).
          b.Opening 110 degrees.
          ** NOTE TO SPECIFIER ** Delete accessories options not required.
          5.Accessories:
          a.Symmetrical Steel Screw Cover Caps:
          1)Personalized: As determined by the Architect.
          2)Embossed logo.
          b.Symmetrical Plastic Screw Cover Caps:
          1)Personalized: As determined by the Architect.
          c.Steel Flange Cover Caps: For Series 200 hinges.
          1)Personalized: As determined by the Architect.
          d.Plastic Flange Cover Caps: For Series B hinges.
          1)Color: Titanium.
          2)Color: Nickel plated.
          3)Color: Titanium.
          4)Color: Nickel plated.
          e.Space for Series 200 Hinges:
          1)Spacer for hinges with 1-3/8 inch (35 mm) diameter. To be used to reduce the cup drilling depth by 0.055 inches (1.4 mm).
          f.Stop Devices: For 155 degree hinges
          1)Limits opening to 135 degrees.
          2)Limits opening to 115 degrees.
          3)Limits opening to 120 degrees.
          4)Limits opening to 92 degrees.
          g.Stop Devices: For Series B hinges
          1)Limits opening to 90 degrees.
          h.Stop Devices: For 94 degree hinges with 1-3/8 inch (35 mm) cup diameter.
          1)Limits opening at 86 degrees.
 
          C.Self-Close Hinges:
          ** NOTE TO SPECIFIER ** Delete hinge options not required and device and finish options not required.
          1.Face Frame Hinges: Stamped steel. Opening: 106 degrees.
          a.S Series Excentra: 2 cam adjustment. 1/4inch (6 mm).
          b.S Series Excentra: 2 cam adjustment. 3/8 inch (9 mm).
          c.S Series Excentra: 2 cam adjustment. 1/2 inch (13 mm).
          d.S Series Excentra: 2 cam adjustment. 1-1/8 inch (29 mm).
          e.S Series Excentra: 2 cam adjustment. 1-1/4 inch (32 mm).
          f.S Series Excentra: 2 cam adjustment. 1-5/16 inch (33 mm).
          g.S Series Excentra: 2 cam adjustment. 1-3/8 inch (35 mm).
          h.S Series Excentra: 2 cam adjustment. 1-7/16 inch (36 mm).
          i.S Series Excentra: 2 cam adjustment. 1-9/16 inch (40 mm).
          j.S Series Excentra: 3 cam adjustment. 1/2 inch (13 mm).
          k.S Series Excentra: 3 cam adjustment. 9/16 inch (14 mm).
          l.S Series Excentra: 3 cam adjustment. 5/8 inch (16 mm).
          m.S Series Excentra: 3 cam adjustment. 3/4 inch (19 mm).
          n.S Series Excentra: 3 cam adjustment. 1 inch (25 mm).
          o.S Series Excentra: 3 cam adjustment. 1-1/4 inch (32 mm).
          p.S Series Excentra: 3 cam adjustment. 1-5/16 inch (33 mm).
          q.S Series Excentra: 3 cam adjustment. 1-3/8 inch (35 mm).
          r.S Series Excentra: 3 cam adjustment. 1-7/16 inch (36 mm).
          s.S Series Excentra: 3 cam adjustment. 1-9/16 inch (40 mm).
          t.Finish: Wood screw, Nickel finish
          u.Finish: Wood screw, Titanium finish
          v.Finish: Dowel, Nickel finish
          w.Finish: Dowel, Titanium Finish: Nickel.
          2.Universal Hinges: Self-closing. Standard application. 110 degrees opening.
          a.Door Type: Glass doors. No drilling of glass is required.
          b.Door Type: Special materials doors, 5/16 inches (8 mm).
          c.Door Type: Lipped doors and doors with molded profiles.
          d.Hinge Type: Integrated soft close.
          e.Hinge Type: Soft close.
          f.Hinge Type: Push opening.
          g.Mounting Adhesive Torsion Load: 118 ft-lbs (160 Nm). When plate is fixed to the glass.
          h.Parallel Side Adjustment: Minus 0.06 to 0.18 inches (minus 1.5 to 4.5 mm).
          i.Height Adjustment: Plus or minus 0.08 inches (plus or minus 2 mm).
          1)Depth Adjustment: Series 200 Mounting Plates. 0.11 inches (2.8 mm).
          2)Depth Adjustment: Domi Snap-On Mounting Plates: from 0.02 to 0.11 inches (0.5 to 2.8 mm).
          3.Self-Closing Hinges: Standard application. Series 100 to 105 degrees opening.
          a.For wooden doors of small weight and (15 to 20 mm) thick.
          1)Full overlay. A Crank: 0 inches (0 mm).
          2)One half inch Overlay. D Crank: 0.20 inches(5 mm).
          3)Half overlay. G Crank: 0.35 inches (9 mm).
          4)Inset. P crank: 0.67 inches (17 mm)
          5)Finish: Nickel.
          6)Fastener: Wood screw.
          7)Fastener: Dowel.
          8)Mounting Plates: Domi Snap-On.
          9)Mounting Plates: Series 200.
          10)Mounting Plates: Face frame.
          b.Adjustments:
          1)Compensating Side Adjustment: Minus 0.06 to 0.18 inches (minus 1.5 to 4.5 mm).
          2)Height Adjustment: Plus or minus 0.08 inches (plus or minus 2 mm).
          3)Depth Adjustment: Series 200 mounting Plates. 0.11 inches (2.8 mm).
          4)Depth Adjustment: Domi Snap-On mounting Plates: from 0.02 to 0.11 inches (0.5 to 2.8 mm).
          4.Self-Closing Hinges: Positive Angled Application. 100 to 105 degrees opening
          a.For wooden doors of small weight and (10 mm) thick minimum.
          1)Arm 15 degrees.
          2)Arm 24 degrees.
          3)Arm 30 degrees.
          4)Arm 37 degrees.
          5)Arm 45 degrees.
          6)Mounting Plates: Domi Snap-On.
          7)Mounting Plates: Series 200.
          8)Mounting Plates: Face frame.
          b.Adjustments:
          1)Compensating Side Adjustment: Minus 0.06 to 0.18 inches (minus 1.5 to 4.5 mm).
          2)Height Adjustment: Plus or minus 0.08 inches (plus or minus 2 mm).
          3)Depth Adjustment: Series 200 mounting Plates. 0.11 inches (2.8 mm).
          4)Depth Adjustment: Domi Snap-On mounting Plates: from 0.02 to 0.11 inches (0.5 to 2.8 mm).
          c.Anti-sliding safety stop.
          5.Inset Blind Corner Hinges. 100 to 105 degrees opening
          a.For wooden doors of small weight and 19/32 to 25/32 inches (15 to 20 mm) thick.
          6.Standard Application Hinges. Series 200. 94 degrees opening
          a.For wooden doors 3/4 to 1-3/4 inches (19 to 35 mm) thick.
          7.Standard Application Hinges. Series 200. 110 degrees opening
          a.For wooden doors medium weight 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          8.Standard Application Hinges. Series 200. 120 degrees opening
          a.For wooden doors medium weight 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          9.Standard Application Hinges. Series 200. 155 degrees opening
          a.For wooden doors medium weight 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          10.Standard Application Hinges. Series 200. 155 degrees opening
          a.For wooden doors 3/4 to 12-27/64 (19 to 36 mm) thick.
          11.Standard Application Hinges. Series 200. 165 degrees opening
          a.For wooden doors medium weight 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          12.Standard Application Hinges. Series 200. 94 degrees opening
          a.For Glass doors 5/32 x 15/64 inches (4 to 6 mm) thick.
          13.Positive Angled Application and Inset Blind Corner Hinges. Series 200. 94 degrees opening
          a.For Glass doors 5/32 x 15/64 inches (4 to 6 mm) thick.
          14.Hinges for Fridge Doors. Series 200. 94 degrees opening
          a.For wooden doors 3/4 to 1-3/4 inches (19 to 35 mm) thick.
          15.Positive Angled Application Hinges. Series 200. 94 degrees opening
          a.For wooden doors 3/4 to 1-3/4 inches (19 to 35 mm) thick.
          16.Negative Angled Application Hinges. Series 200. 120 degrees opening
          a.For wooden doors medium weight 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          17.Inset Blind Corner Hinges. Series 200. 94 degrees opening
          a.For wooden doors 3/4 to 1-3/4 inches (19 to 35 mm) thick.
          18.Long Inset Blind Corner Hinges. Series 200. 110 degrees opening
          a.For wooden doors medium weight 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          19.Inset Blind Corner Hinges. Series 200. 70 degrees opening
          a.For wooden doors 3/4 to 1-3/4 inches (19 to 35 mm) thick.
          20.Standard Application Hinges. Series F. 94 degrees opening
          a.For wooden doors 3/4 to 1-3/4 inches (19 to 35 mm) thick.
          21.Standard Application Hinges. Metal profiles Series 200. 105 degrees opening.
          a.For aluminum frame doors 25/32 inches (20 mm) thick.
          22.Positive Angled Application Hinges. Metal profiles Series 200. 105 degrees opening.
          a.For aluminum frame doors 25/32 inches (20 mm) thick.
          23.Inset Blind Corner Hinges. Metal profiles Series 200. 105 degrees opening.
          a.For aluminum frame doors 25/32 inches (20 mm) thick.
          24.Standard Application Hinges. Metal profiles Series 400. 94 degrees opening.
          a.For aluminum frame doors 25/32 inches (20 mm) thick.
          25.Positive Angled Application and Crampon Hinges. Metal profiles Series 400. 94 degrees opening.
          a.For aluminum frame doors 25/32 inches (20 mm) thick.
          26.Standard Application Hinges. Series 400 Mini hinges. 94 degrees opening.
          a.For wooden doors 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          27.Positive Angled Application and Inset Blind Corner Hinges. Series 400 Mini hinges. 94 degrees opening.
          a.For wooden doors 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          28.Standard Application Hinges. Series 600 Mini hinges. 94 degrees opening.
          a.For wooden doors 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          29.Positive Angled Application Hinges. Series 600 Mini hinges. 94 degrees opening.
          a.For wooden doors 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          30.Inset Blind Corner Hinges for Smaller Spaces. Series 600 Mini hinges. 94 degrees opening.
          a.For wooden doors 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          31.Standard Application Hinges. Series 600 Mini hinges. 94 degrees opening.
          a.For glass doors 5/32 x 15/64 inches (4 to 6 mm) thick.
          32.Positive Angled Application and Inset Blind Corner Hinge. Series 600 Mini hinges. 94 degrees opening.
          a.For glass doors 5/32 x 15/64 inches (4 to 6 mm) thick.
          33.Standard Application Hinges. Series M. 270 degrees opening.
          a.For wooden doors 5/8 to 1-1/32 inches (16 to 26 mm) thick.
 
          D.Special Applications:
          ** NOTE TO SPECIFIER ** Delete hinge options not required and device options not required.
          1.Universal Hinges:
          a.Standard Application: Universal hinges with integrated soft close. 110 degrees opening. For glass doors. No drilling of glass required.
          b.Standard Application: Universal hinges with integrated soft close. 110 degrees opening. For special material doors.
          c.Standard Application: Half-inset doors and doors with molded profiles. Universal hinges with integrated soft close. 110 degrees opening. For wood doors 15/32 to 25/32 inches (12 to 20 mm) thick.
          2.Face Frame Hinges: CU Series.
          a.Silentia Excentra: 2 cam adjustment with integrated soft close. 106 degrees opening. Door Thickness: 9/16 to 7/8 inches (14 to 22 mm)
          b.Silentia Excentra: 3 cam adjustment with integrated soft close. 106 degrees opening. Door Thickness: 9/16 to 7/8 inches (14 to 22 mm)
          3.Face Frame Hinges: S Series
          a.Silentia Excentra: 2 cam adjustment. 106 degrees opening. Door Thickness: 1/2 to 1-9/16 inches (13 to 40 mm)
          b.Silentia Excentra: 3cam adjustment. 106 degrees opening. Door Thickness: 1/2 to 1-9/16 inches (13 to 40 mm)
          4.Air Hinges: Inserts into and bottom of cabinet and in the door. 105 degree opening. Wooden and aluminum framed doors. Finish: Nickel and Titanium.
          a.Aluminum Door Profile Width: 1-1/32 inches (26 mm). Glass insertion slot: 5/32 inches (4 mm).
          b.Aluminum Door Profile Width: 3/4 inches (19 mm). Glass insertion slot: 5/32 inches (4 mm).
          c.Corner connectors.
          d.Glass gasket.
          e.Angle Reduction Clip: Reduces opening angle to 92 degrees.
          f.Sleeves: For insertion of corner connectors. Plastic or aluminum.
          5.Air Push Hinges: Equipped with spring for opening of handle-less doors. 105 degree opening. Wooden and aluminum framed doors. Finish: Nickel and Titanium.
          a.Aluminum Door Profile Width: 1-1/32 inches (26 mm). Glass insertion slot: 5/32 inches (4 mm).
          b.Aluminum Door Profile Width: 3/4 inches (19 mm). Glass insertion slot: 5/32 inches (4 mm).
          c.Corner connectors.
          d.Release devices and retaining catches.
          6.Lapis Hinges:
          a.Series 200 with Covers. 94 degrees opening. Adjustable soft-close mechanism operated by twin silicone-oil dampers housed in the hinge cup. For wooden doors 3/4 to 1-3/8 inches (19 to 35 mm) thick.
          b.Series 700 with Covers. 110 degrees opening. Adjustable soft-close mechanism operated by twin silicone-oil dampers housed in the hinge cup. For wooden doors 5/8 to 1-1/32 inches (16 to 26 mm) thick.
          c.Finish: Satin Chrome, Satin Metal Black, Satin Gold, Champagne, Glossy Chrome, glossy Metal Black, Stainless steel, Graphite, glossy Gold, Old Brass, Matt White,
          7.Lapis Push Hinges:
          a.Series 200 with Covers. 94 degrees opening. Adjustable soft-close mechanism operated by twin silicone-oil dampers housed in the hinge cup. Equipped with spring for opening handle-less doors. For wooden doors 3/4 to 1-3/8 inches (19 to 35 mm) thick, 3.3 to 20.9 lbs (1.5 to 9.5 kg). Decelerated opening action.
          8.Pacta Hinges: With Smove system for single doors. System for fall flaps.90 degree opening. Wooden Doors 11-1/32 to 15-3/4 inches (280 to 400 mm) in height, 3.3 to 20.9 lbs (1.5 to 9.5 kg). Decelerated opening action.
          9.Pacta Hinges: With Push system for single doors. System for fall flaps.90 degree opening. Wooden Doors 11-1/32 to 15-3/4 inches (280 to 400 mm) in height, 3.3 to 20.9 lbs (1.5 to 9.5 kg). Decelerated opening action.
          ** NOTE TO SPECIFIER ** Delete article if not required or delete paragraph options not required.
 
          2.3RUNNERS AND SPACE ORGANIZERS
 
          A.Metal Drawers: LINABOX Series.
          ** NOTE TO SPECIFIER ** Delete drawer type options not required.
          1.Drawer Type: 2-sided drawer - H 75. Aluminum metal sides, wood sub-front and back panel.
          a.Height of Metal Side: 2-31/32 inches (75 mm).
          b.Internal Height: 1-13/16 inches (46 mm).
          c.Wood Thickness: 5/8 inches (16 mm).
          2.Drawer Type: 2-sided drawer - H 101 mm. Aluminum metal sides, wood sub-front and back panel.
          a.Height of Metal Side: 3-31/32 inches (101 mm).
          b.Internal Height: 2-13/16 inches (72 mm).
          c.Wood Thickness: 5/8 inches (16 mm).
          3.Drawer Type: 2-sided drawer - H 178 mm. Aluminum metal sides, wood sub-front and back panel.
          a.Height of Metal Side: 7 inches (178 mm).
          b.Internal Height: 5-7/8 inches (149 mm).
          c.Wood Thickness: 5/8 inches (16 mm).
          4.Drawer Type: 2-sided drawer - H 237 mm. Aluminum metal sides, wood sub-front and back panel.
          a.Height of Metal Side: 9-5/16 inches (237 mm).
          b.Internal Height: 8-3/16 inches (208 mm).
          c.Wood Thickness: 5/8 inches (16 mm).
          5.Drawer Type: 4-sided pull-out drawer with solid front piece - H 100 mm. Aluminum metal drawer with a rapid assembly system, with no machinery or templates needed.
          a.Height of Front: 3-15/16 inches (100 mm).
          b.Hight of side: 2-31/32 inches (75 mm).
          c.Internal Height: 1-13/16 inches (46 mm).
          6.Drawer Type: 4-sided pull-out drawer with solid front piece - H 126 mm. Aluminum metal drawer with a rapid assembly system, with no machinery or templates needed.
          a.Height of Front: 4-31/32 inches (126 mm).
          b.Hight of side: 3-31/32 inches (101 mm).
          c.Internal Height: 2-13/16 inches (72 mm).
          7.Drawer Type: 4-sided pull-out drawer with 8 mm design element - H 126 mm. Aluminum metal drawer with a rapid assembly system, with no machinery or templates needed.
          a.Height of Front: 4-31/32 inches (126 mm).
          b.Hight of side: 3-31/32 inches (101 mm).
          c.Internal Height: 2-13/16 inches (72 mm).
          8.Drawer Type: 4-sided pull-out drawer with metal front gallery - H 203 mm. Aluminum metal drawer with a rapid assembly system, with no machinery or templates needed.
          a.Height of Front: 8 inches (203 mm).
          b.Hight of side: 7 inches (178 mm).
          c.Internal Height: 5-7/8 inches (149 mm).
          9.Drawer Type: Under-sink, 2-sided drawer - H 101 mm. Aluminum metal sides, wood sub-front and back panel.
          a.Height of Front: 8 inches (203 mm).
          b.Hight of Side: 3-31/32 inches (101 mm).
          c.Internal Height: 2-13/16 inches (72 mm).
          d.Wood Thickness: 5/8 inches (16 mm).
 
          B.Concealed Runners:
          ** NOTE TO SPECIFIER ** Delete runner options not required and delete device options not required.
          1.Futura Smove Runners: Soft closing.
          a.Full-extension, Clip Version 7555. Runner fixed to drawer by clip. Finish: bright zinc-plated. Drawer Material: 5/8 inches (16 mm).
          1)Static Load Capacity: 100 lbs (45.34 kg).
          2)Dynamic Load Capacity: 75 lbs (34.02 kg).
          3)Clip: 6 way adjustable clip.
          4)Clip: Vertical adjustment.
          5)Clip: Narrow drawer clip.
          6)Clip with height, side, and depth adjustment.
          7)Socket: Plastic plug-in.
          8)Socket: Plastic screw on.
          9)Socket: Plastic screw on for 9 inch (229 mm) runner.
          10)Socket: Steel.
          11)Socket: Narrow steel.
          12)Runner Length: 12-13/32 inches (315 mm).
          13)Runner Length: 15-3/8 inches (391 mm).
          14)Runner Length: 18-3/8 inches (467 mm).
          15)Runner Length: 21-3/8 inches (543 mm).
          b.Full-extension, Clip Version 7955. Runner fixed to drawer by clip. Finish: bright zinc-plated. Drawer Material: 3/4 inches (19 mm).
          1)Static Load Capacity: 100 lbs (45.34 kg).
          2)Dynamic Load Capacity: 75 lbs (34.02 kg).
          3)Clip: 6 way adjustable clip.
          4)Clip: Vertical adjustment.
          5)Clip: Narrow drawer clip.
          6)Clip with height, side, and depth adjustment.
          7)Socket: Plastic plug-in.
          8)Socket: Plastic screw on.
          9)Socket: Plastic screw on for 9 inch (229 mm) runner.
          10)Socket: Steel.
          11)Socket: Narrow steel.
          12)Runner Length: 12-13/32 inches (315 mm).
          13)Runner Length: 15-3/8 inches (391 mm).
          14)Runner Length: 18-3/8 inches (467 mm).
          15)Runner Length: 21-3/8 inches (543 mm).
          2.Futura Push Runners: With push opening systems and soft closing for handle-less drawers
          a.Full-extension, Clip Version 7557. Full-extension runner fixed to drawer by clip. Finish: bright zinc-plated. Drawer Material: 5/8 inches (16 mm).
          1)Static Load Capacity: 100 lbs (45.34 kg).
          2)Dynamic Load Capacity: 75 lbs (34.02 kg).
          3)Clip: 6 way adjustable clip.
          4)Clip: Vertical adjustment.
          5)Clip: Narrow drawer clip.
          6)Clip with height, side, and depth adjustment.
          7)Socket: Plastic plug-in.
          8)Socket: Plastic screw on.
          9)Socket: Plastic screw on for 9 inch (229 mm) runner.
          10)Socket: Steel.
          11)Socket: Narrow steel.
          12)Runner Length: 10-11/32 (263 mm).
          13)Runner Length: 12-13/32 inches (315 mm).
          14)Runner Length: 15-3/8 inches (391 mm).
          15)Runner Length: 18-3/8 inches (467 mm).
          16)Runner Length: 21-3/8 inches (543 mm).
          3.Futura Self Closing Runners:
          a.Full-extension, Clip Version 755. Full-extension runner fixed to drawer by clip. Finish: bright zinc-plated. Drawer Material: 5/8 inches (16 mm).
          1)Static Load Capacity: 100 lbs (45.34 kg).
          2)Dynamic Load Capacity: 75 lbs (34.02 kg).
          3)Clip: 6 way adjustable clip.
          4)Clip: Vertical adjustment.
          5)Clip: Narrow drawer clip./
          6)Clip with height, side, and depth adjustment
          7)Socket: Plastic plug-in.
          8)Socket: Plastic screw on.
          9)Socket: Plastic screw on for 9 inch (229 mm) runner.
          10)Socket: Steel.
          11)Socket: Narrow steel.
          12)Socket: Narrow steel.
          13)Runner Length: 10-11/32 (263 mm).
          14)Runner Length: 12-13/32 inches (315 mm).
          15)Runner Length: 15-3/8 inches (391 mm).
          16)Runner Length: 18-3/8 inches (467 mm).
          17)Runner Length: 21-3/8 inches (543 mm).
 
          C.Pull-Out Shelf:
          ** NOTE TO SPECIFIER ** Delete runner options not required and delete device options not required.
          1.SMOVE 65559 - Concealed Runner. Full-extension runner fixed to the shelf by clip.
          a.Runner Length: 13-25/32 inches (350 mm).
          b.Runner Length: 15-3/4 inches (400 mm).
          c.Runner Length: 17-23/32 inches (450 mm).
          d.Runner Length: 1-31/32 inches (500 mm).
          e.Runner Length: 21-21/32 inches (550 mm).
          f.Runner Length: 23-5/8 inches (600 mm).
          g.Dynamic Load Capacity: 66.14 lbs (30 kg)
          h.Integrated Smove system.
          i.Full-extension.
          2.PUSH 65579 - Concealed Runner. Full-extension runner fixed to the shelf by clip.
          a.Runner Length: 13-25/32 inches (350 mm).
          b.Runner Length: 15-3/4 inches (400 mm).
          c.Runner Length: 17-23/32 inches (450 mm).
          d.Runner Length: 1-31/32 inches (500 mm).
          e.Runner Length: 21-21/32 inches (550 mm).
          f.Runner Length: 23-5/8 inches (600 mm).
          g.Dynamic Load Capacity: 66.14 lbs (30 kg)
          h.Integrated Push system.
          i.Full-extension.
 
          D.Waste Bin Systems:
          1.Composed of Shelf runners, pre-mounted on a steel support, fully assembled Lineabox drawer, steel bin-holder frame and bins.
          a.Adjustable Steel Support:
          1)Depth adjustment with the runner fixing clips.
          2)Sideways, vertical and tilt adjustment on the runners support.
          b.Height of the Lineabox metal side 7-3/32 inches (180 mm).
          c.Runner Length: 1-31/32 inches (500 mm).
          ** NOTE TO SPECIFIER ** Delete storage unit width options not required.
          d.Storage Unit Width: 12 inches (305 mm). Plastic Waste Bin: 35 qt (33 L).
          e.Storage Unit Width: 15 inches (381 mm). 2 Plastic Waste Bins: 32 qt (30 L).
          f.Storage Unit Width: 18 inches (457 mm). 2 Plastic Waste Bins: 32 qt (30 L).
          g.Storage Unit Width: 21 inches (533 mm). 2 Plastic Waste Bins: 35 qt (33 L).
          h.Finishes:
          1)Bin-Holder Frame: Titanium.
          2)Waste Bins: Grey.
          3)Runners Support: Grey.
          4)Lineabox Sides: White, Stainless steel.
 
          E.Pull-Out Units: Waste bins.
          1.Composed by two runners fixed to the right or left side of cabinet and two fully assembled Lineabox drawers, premounted on a frame. Integrated Smove system.
          a.Depth, vertical and sideways adjustment with the runner fixing clips.
          b.For cabinets with side thickness 5/8 to 3/4 inches (16 to 19 mm).
          c.Central Drawer Length: 13-25/32 inches (350 mm).
          d.Runner Length: 19-11/16 inches (500 mm).
          ** NOTE TO SPECIFIER ** Delete width and finish options not required.
          e.Width: 4-1/2 inches (115 mm).
          f.Width: 6 inches (153 mm).
          g.Width: 12 inches (305 mm).
          1)One Shelf runner, 19-11/16 inches (500 mm) length, fixed to bottom of cabinet.
          h.Finish: Lineabox Sides: White.
          i.Finish: Lineabox Sides: Stainless steel.
 
          F.Kitchen Space Organizers:
          ** NOTE TO SPECIFIER ** Delete space organizers not required and then delete the options for the remaining organizers not required.
          1.Pull-Out Base Fillers: 2-tier base organizer for frame and frameless cabinets. Non-slip melamine surfaces. Comes fully assembled.
          a.Minimum Opening: 6 inch (152 mm).
          1)Components: 2-tier side pull-out unit, full extension soft close slide, 2 adjustable door-mounting brackets, and drilling template.
          b.Minimum Opening: 4-1/2 inch (114 mm).
          1)Components: 3-tier side pull-out unit, full extension soft close slide, 2 adjustable door-mounting brackets, and drilling template.
          c.Full extension soft close.
          d.Load Capacity 75 Ibs (35 kg).
          e.Door Adjustment: 3-way.
          f.Color Steel Wire Parts: Chrome white melamine.
          g.Color Steel Wire Parts: Champagne.
          h.Melamine Bottom: White.
          i.Melamine Bottom: American maple.
          j.Melamine Bottom: Gray.
          2.Pull-Out Organizer: 2-tier base organizer for frame and frameless cabinets. Non-slip melamine surfaces. Comes fully assembled.
          a.Components: 2-tier side pull-out unit, full extension soft close slide, 2 adjustable door-mounting brackets, snap-on pull-out dividers, and drilling template.
          b.Full extension soft close.
          c.Load Capacity 75 Ibs (35 kg).
          d.Door Adjustment: 3-way.
          e.Width: 12 inches (305 mm).
          f.Width: 15 inches (381 mm).
          g.Width: 18 inches (457 mm).
          h.Height: 20 inches (508 mm). Depth: 21-3/8 inches (543 mm).
          i.Color Steel Wire Parts: Chrome white melamine.
          j.Color Steel Wire Parts: Champagne.
          k.Melamine Bottom: Color: White.
          l.Melamine Bottom: Color: American maple.
          m.Melamine Bottom: Color: Gray.
          3.Wire Pull-Out Drawers: For frame and frameless cabinets. Easy drawer insertion and removal. Nonslip melamine surfaces.
          a.Components: 1 drawer pull-out unit.
          b.Full extension. Soft close slide 20-31/32 inches (533 mm).
          c.Load capacity 75 Ibs (35 kg).
          d.Side and bottom mount.
          e.Width: 12 inches (305 mm).
          f.Width: 15 inches (381 mm).
          g.Width: 18 inches (457 mm).
          h.Width: 21 inches (533 mm).
          i.Height: 5-3/8 inches (136 mm). Depth: 21-3/8 inches (543 mm).
          j.Color Steel Wire Parts: Chrome.
          k.Color Steel Wire Parts: Champagne.
          l.Melamine Bottom: Color: White.
          m.Melamine Bottom: Color: American maple.
          4.Spacers: For face frame cabinets. Bottom mounted spacers and adjustable side mounted spacers for face frame cabinets. The spacers can be used for drawers, pull-outs, and trash cans.
          a.Components: 4 brackets, 2 spacers and attachment screws.
          b.Finish: Zinc coated.
          c.Side mount no spacers.
          d.Bottom mount spacers.
          e.Spacer Type: Side mount with 1 adjustable spacer minimized.
          f.Spacer Type: Side mount with 1 adjustable spacer maximized.
          g.Spacer Type: Side mount with 2 adjustable spacer minimized.
          h.Spacer Type: Side mount with 2 adjustable spacer maximum.
          5.Smart Corner: For frameless cabinets. Full extension soft close. Open in one movement. Nonreversible. Automatically allows free access to rear baskets.
          a.Requires a minimum door opening of 17 inches (432 mm).
          b.Nonslip surface.
          c.Load Capacity: Back Shelves: 44 lbs (20 kg). Front shelves: 22 lbs (10 kg ). Inside Height: 22-3/8 inch (568 mm) minimum.
          d.Components: Set of 4 baskets, 2 front and 2 rear, full extension soft close slides, (400 mm), adjustable door mounting bracket.
          e.Door Opening Angle: Can be adjusted in three distinct positions.
          f.Size (WxDxH): 33-5/16 x 19-1/4 x 22-3/8 inches (846 x 489 x 568 mm).
          g.Color Steel Wire Parts: Chrome.
          h.Color Steel Wire Parts: Champagne.
          i.Melamine Bottom: Color: White.
          j.Melamine Bottom: Color: American maple.
          6.Fly Moon: For frame and frameless corner cabinets. Space saving corner unit with shelves designed to increase storage surface. Load capacity 44 lbs (20 kg) per shelf. Door Opening: 85 degrees minimum,
          a.Shaft Mechanism: Height adjustable shaft, brackets, and extension pipe.
          1)Can be fixed to one side of the cabinet.
          2)Color Steel Wire Parts: Champagne.
          3)Color Steel Wire Parts: Gray.
          b.Shelves: Two pivoting shelves that can be pulled-out independently.
          1)Right or left opening.
          2)Surface: Non-slip melamine.
          3)Shelf Rail Height: 2-3/4 inch (70 mm).
          4)Metal Plates: For connection to shaft mechanism.
          5)Soft close version available.
          6)Shelf Size (WxDxH): 29 x 16-1/32 x 3-3/8 inches (737 x 407 x 86 mm).
          a)Opening: 13-5/8 inches (346 mm).
          7)Shelf Size (WxDxH): 32-3/16 x 17-3/8 x 3-3/8 inches (818 x 441 x 86 mm).
          a)Opening: 16 inches (406 mm).
          8)Shelf Size (WxDxH): 38-7/16 x 18-3/4 x 3-3/8 inches (976 x 476 x 86 mm).
          a)Opening: 21 inches (533 mm).
          9)Color Steel Wire Parts: Chrome.
          10)Color Steel Wire Parts: Champagne.
          11)Melamine Bottom: Color: White.
          12)Melamine Bottom: Color: American maple.
          7.Swivel Carousels: For frame and frameless based corner cabinets. Independent shelf rotation. Non-slip melamine surface.
          a.Components:
          1)Pivoting Carousels Shelves: Two, 270 degree circle. Height adjustable.
          a)Diameter: 28-3/16 inches (716 mm). Load Capacity: 29 lbs (13 kg) per shelf.
          b)Diameter: 32-1/8 inches (816 mm). Load Capacity: 35 lbs (16 kg) per shelf.
          c)Shelf Rail Height: 4-3/8 inches (111 mm).
          d)Color Steel Wire Parts: Chrome.
          e)Color Steel Wire Parts: Champagne.
          f)Melamine Bottom: Color: White.
          g)Melamine Bottom: Color: American maple.
          2)Carousel Posts: 1 inch (25 mm) diameter with top and bottom fittings.
          a)Height Adjustable 25-7/16 to 31-1/16 inch (646 top 789 mm).
          b)Finish: Chrome.
          8.Rotating Pantry Unit: Soft close return. 90 degree rotation of the frame.
          a.Slide: Full extension pivoting slide with soft close return. 90 degree rotation of the frame to the right or to the left side.
          1)Load Capacity: 220 lbs (100 kg)
          2)Dimensions (DxH): 19-11/16 x 10-15/32 inch (500 x 266 mm)
          b.Brackets: Adjustable door-mounting bracket, fast application to frame internal holes. Doors over 7 ft (2134 mm) tall: Use 3 door-mounting brackets.
          1)Size (DxWxH): 1-5/8 x 9-7/8 x 1-3/16 inches (41 x 251 x 30 mm).
          2)Size (DxWxH): 1-5/8 x 13-13/16 x 1-3/16 inches (41 x 351 x 30 mm).
          3)Size (DxWxH): 1-5/8 x 15-3/4 x 1-3/16 inches (41 x 400 x 30 mm).
          4)Size (DxWxH): 1-5/8 x 21-5/8 x 1-3/16 inches (41 x 549 x 30 mm).
          5)Color: Champagne.
          6)Color: Gray.
          c.Basket: Nonslip melamine surface, height adjustable basket assembly.
          1)Size (DxWxH): 16-3/16 x 9-11/16 x 3-11/16 inches (411 x 246 x 94 mm).
          2)Size (DxWxH): 16-3/16 x 13-5/8 x 3-11/16 inches (411 x 346 x 94 mm).
          3)Size (DxWxH): 16-3/16 x 15-5/8 x 3-11/16 inches (411 x 397 x 94 mm).
          4)Size (DxWxH): 16-3/16 x 21-1/2 x 3-11/16 inches (411 x 546 x 94 mm).
          5)Color Steel Wire Parts: Chrome.
          6)Color Steel Wire Parts: Champagne.
          7)Melamine Bottom: Color: White.
          d.Frame: Height-adjustable frame, for overlay and inset doors.
          1)Color: Champagne.
          2)Color: Gray.
          3)Size (DxWxH): 19-9/16 x 1-3/16 x 46-7/32 to 63-17/32 inches (497 x 30 x 1182 to 1614 mm)
          a)Number of Baskets: 3.
          4)Size (DxWxH): 19-9/16 x 1-3/16 x 61-31/32 to 79-9/32 inches (497 x 30 x 1574 to 2014 mm)
          a)Number of Baskets: 4.
          5)Size (DxWxH): 19-9/16 x 1-3/16 x 73-25/32 to 91-3/32 inches (497 x 30 x 1879 to 2314 mm)
          a)Number of Baskets: 5.
          9.Straight Pantry Unit: Soft close return.
          a.Slide: Full extension slide with soft close return.
          1)Load Capacity: 265 lbs (120 kg)
          2)Size (DxWxH): 18-7/8 x 21 x 5-1/2 inches (479 x 533 x 140 mm).
          b.Brackets: Adjustable door-mounting bracket.
          1)Doors over 7 ft (2134 mm) Tall: Use 3 door-mounting brackets.
          2)Size (DxWxH): 1-5/8 x 9-7/8 x 1-3/16 inches (41 x 251 x 30 mm).
          3)Size (DxWxH): 1-5/8 x 13-13/16 x 1-3/16 inches (41 x 351 x 30 mm).
          4)Size (DxWxH): 1-5/8 x 15-3/4 x 1-3/16 inches (41 x 400 x 30 mm).
          5)Size (DxWxH): 1-5/8 x 21-5/8 x 1-3/16 inches (41 x 549 x 30 mm).
          6)Color: Champagne.
          7)Color: Gray.
          c.Frame: Height-adjustable frame, for overlay and inset doors.
          1)Color: Champagne.
          2)Color: Gray.
          3)Size (DxWxH): 19-9/16 x 1-3/16 x 41-23/32 to 59-1/16 inches (497 x 30 x 1060 to 1500 mm).
          a)Number of Baskets: 3.
          4)Size (DxWxH): 19-9/16 x 1-3/16 x 57-15/32 to 74-13/16 inches (497 x 30 x 1460 to 1900 mm).
          a)Number of Baskets: 4.
          5)Size (DxWxH): 19-9/16 x 1-3/16 x 69-9/32 to 86-5/8 inches (497 x 30 x 1760 to 2200 mm)
          a)Number of Baskets: 5.
          d.Basket: Nonslip melamine surface, height adjustable basket assembly.
          1)Size (DxWxH): 16-3/16 x 9-11/16 x 3-11/16 inches (411 x 246 x 94 mm).
          2)Size (DxWxH): 16-3/16 x 13-5/8 x 3-11/16 inches (411 x 346 x 94 mm).
          3)Size (DxWxH): 16-3/16 x 15-5/8 x 3-11/16 inches (411 x 397 x 94 mm).
          4)Size (DxWxH): 16-3/16 x 21-1/2 x 3-11/16 inches (411 x 546 x 94 mm).
          5)Color Steel Wire Parts: Chrome.
          6)Color Steel Wire Parts: Champagne.
          7)Melamine Bottom: Color: White.
          10.Maxi-Pantry Unit: Easy fit system. Reversible, for left or right hand doors.
          a.Integrated system allowing pullouts to move forward as the door is opened.
          b.Tall pantry system allowing easy and full access to contents.
          c.Opening Hinges: 165 degrees.
          d.Load capacity 175 lbs (80 kgs).
          e.Frame: Pull-out.
          1)Color: Champagne.
          2)Color: Gray.
          f.Opening: 16-5/16 inches (414 mm).
          1)Frame Size (DxWxH): 18-3/4 x 12-7/8 x 48-1/32 to 61-13/16 inches (475 x 327 x 1220 to 1570 mm).
          a)Number of Baskets: 3.
          2)Frame Size (DxWxH): 18-3/4 x 12-7/8 x 61-13/16 to 75-5/8 inches (475 x 327 x 1570 to 1921 mm).
          a)Number of Baskets: 4.
          3)Frame Size (DxWxH): 18-3/4 x 12-7/8 x 75-5/8 to 85-7/8 inches (475 x 327 x 1921 to 2181 mm).
          a)Number of Baskets: 5.
          g.Opening: 22-3/16 inches (564 mm).
          1)Frame Size (DxWxH): 18-3/4 x 18-3/4 x 48-1/32 to 61-13/16 inches (475 x 475 x 1220 to 1570 mm).
          a)Number of Baskets: 3.
          2)Frame Size (DxWxH): 18-3/4 x 18-3/4 x 61-13/16 to 75-5/8 inches (475 x 475 x 1570 to 1921 mm).
          a)Number of Baskets: 4.
          3)Frame Size (DxWxH): 18-3/4 x 18-3/4 x 75-5/8 to 85-7/8 inches (475 x 475 x 1921 to 2181 mm).
          a)Number of Baskets: 5.
          h.Basket: Basket for maxi-pantry unit. Easy insertion and removal, non-slip melamine surface, height adjustable basket assembly.
          1)Size (DxWxH): 16-3/16 x 12-5/8 x 6-1/4 inches (411 x 321 x 159 mm)
          2)Size (DxWxH): 16-3/16 x 18-1/2 x 6-1/4 inches (411 x 470 x 159 mm)
          3)Color Steel Wire Parts: Chrome.
          4)Color Steel Wire Parts: Champagne.
          5)Melamine Bottom: Color: White.
          6)Melamine Bottom: Color: American maple.
          11.Waste and Recycle: Bottom mount or side mount. Full extension: 16-11/16 inches (500 mm). Soft close. Installs with 4 screws. Used on various door widths; particularly 5-pieces doors.
          a.Waste Bins: Recyclable, nontoxic material. Resistant to low and elevated temperatures. Non deformable. Integrated handles for easy removal.
          b.Door-Mount Bracket: Adjustable. For use on various door widths.
          1)Cabinet Door Alignment: 3 way adjustability.
          a)Height: Plus or minus 5/64 inches (Plus or minus 2 mm).
          b)Side: Plus or minus 1/8 inches(Plus or minus 3 mm).
          c)Depth: Plus or minus 5/32 inches (Plus or minus 4 mm).
          12.Waste Recycle Pullouts: Soft close. Wire bottom. Full Extension: 19-11/16 inches (500 mm)
          a.Base: 12 inch (305 mm) pull-out waste bins. Adjustable door mount bracket allows for use on various door widths; particularly 5-pieces doors. Handle and door brackets included.
          1)Plastic Waste Bins: One 35 Qt. Equipped with handles to keep trash bag inside and lift cans up.
          2)Size (DxWxH): 19-5/8 x 12 x 19-1/2 inches (422 x 305 x 495 mm)
          b.Base: 15 inch (381 mm) pull-out waste bins. Adjustable door mount bracket allows for use on various door widths; particularly 5-pieces doors. Handle and door brackets included.
          1)Plastic Waste Bins: One 35 Qt (33.12 L). Equipped with handles to keep trash bag inside and lift cans up.
          2)Size (DxWxH): 19-5/8 x 15 x 19-1/2 inches (422 x 381 x 495 mm).
          c.Base: 18 inch (457 mm) pull-out waste bins. Adjustable door mount bracket allows for use on various door widths; particularly 5-pieces doors. Handle and door brackets included.
          1)Plastic Waste Bins: One 35 Qt (33.12 L). Equipped with handles to keep trash bag inside and lift cans up.
          2)Size (DxWxH): 19-5/8 x 18 x 19-1/2 inches (422 x 457 x 495 mm).
          d.Base: 21 inch (533 mm) pull-out waste bins. Adjustable door mount bracket allows for use on various door widths; particularly 5-pieces doors. Handle and door brackets included.
          1)Plastic Waste Bins: One 35 Qt (33.12 L). Equipped with handles to keep trash bag inside and lift cans up.
          2)Size (DxWxH): 19-5/8 x 21 x 19-1/2 inches (422 x 533 x 495 mm).
          13.Single 50 qt Waste Recycle Pullout: Adjustable door mount bracket. Bottom mounted. Full extension slides with over-travel functionality. For use on various door widths; particularly 5-pieces doors. Soft close.
          a.Door mount brackets.
          b.Load Capacity: 100 lbs (45.36 kg).
          c.Size (DxWxH): 22 x 11-1/2 x 24-1/16 inches (559 x 292 x 611 mm).
          d.Plastic Waste Bins: One 50 qt (47.32 L) and one 11 qt (10.41 L).
          1)Material: Recyclable, nontoxic. Low and high temperature resistant.
          2)Non deformable.
          3)Integrated handles for easy removal.
          4)Lid available (sold separately).
          14.Double 50 qt (47.32 L) Waste Recycle Pullout: Adjustable door mount bracket. Bottom mounted. Full extension slides with over-travel functionality. For use on various door widths; particularly 5-pieces doors. Soft close.
          a.Door mount brackets
          b.Load Capacity: 100 lbs (45.36 kg).
          c.Size (DxWxH): 22 x 14-1/2 x 24-1/16 inches (559 x 368 x 611 mm).
          d.Plastic Waste Bins: Two 50 qt (47.32 L).
          1)Material: Recyclable, nontoxic. Low and high temperature resistant.
          2)Non deformable.
          3)Integrated handles for easy removal.
          4)Lid available (sold separately).
          15.Under the Sink Pullouts 12 inch (305 mm) Base Cabinet: Integrated handle. Bottom mount. Full extension. Soft close. Installs with 4 wood screws
          a.Size (DxWxH): 19-5/8 x 11-3/4 x 14-1/2 inches (498 x 298 x 368 mm).
          b.Plastic Waste Bins: Two 16 qt (15.14 L)
          1)Material: Recyclable, nontoxic. Low and high temperature resistant.
          2)Non deformable.
          3)Integrated handles for easy removal.
          4)Front Handle Height: 15-1/16 inches (408 mm)
          5)Lid.
          16.Under the Sink Pullouts 15 inch (381 mm) Base Cabinet: Integrated handle. Bottom mount. Full extension. Soft close. Installs with 4 wood screws
          a.Load Capacity: 75 lbs (34 kg)
          b.Size (DxWxH): 17-11/16 x 15 x 19-1/2 inches (449 x 381 x 495 mm).
          c.Plastic Waste Bins: One 32 qt (30.28 L) and one rear basket for small storage.
          1)Material: Recyclable, nontoxic. Low and high temperature resistant.
          2)Non deformable.
          3)Integrated handles for easy removal.
          4)Front Handle Height: 15-1/16 inches (408 mm).
          5)Lid.
          17.Waste Recycle Accessories:
          a.Small Bin 3.2 qt. (DxWxH): 7-7/8 x 7-23/32 x 3-9/16 inch (200 x 196 x 90 mm).
          b.Small Bin 5.3 qt (DxWxH): 7-7/8 x 7-23/32 x 7-3/4 inch (200 x 196 x 197 mm).
          c.Waste Bin 11 qt (DxWxH): 7-3/16 x 8-17/32 x 14-1/2 inch (183 x 217 x 368 mm).
          d.Waste Bin 32 qt (DxWxH): 14-3/8 x 8-5/8 x 18-7/64 inch (365 x 219 x 460 mm).
          e.Waste Bin 35 qt (DxWxH): 17-15/64 x 8-5/8 x 18-7/64 inch (438 x 219 x 460 mm).
          f.Waste Bin 50 qt (DxWxH): 10-5/8 x 13-3/4 x 22-7/16 inch (270 x 349 x 570 mm).
          g.Lid with Filter (DxW): 14-3/8 x 8-5/8 inch (365 x 219 mm).
          h.Lid with Filter (DxW): 17-15/64 x 8-5/8 inch (438 x 219 mm).
          i.Lid with Filter (DxW): 12-7/8 x 10-1/16 inch (327 x 256 mm).
          j.Lid with Filter (DxW): 7-11/16 x 6-5/8 inch (195 x 168 mm).
          ** NOTE TO SPECIFIER ** Delete article if not required or delete paragraphs not required.
 
          2.4LIFT SYSTEMS AND SYSTEMS FOR FALL FLAPS
 
          A.Lift Systems:
          1.Evolift: Flap door opening system for wooden and Aluminum-frame doors. Coil-spring movement with covers/
          ** NOTE TO SPECIFIER ** Delete flap door option not required.
          a.Flap Door, Soft Close:
          1)Door Height: 11-13/16 to 23-5/8 inches (300 to 600 mm). Door Weight: 3.3 to 39.7 lbs (1.5 to 18 kg).
          b.Flap Door, Push Opening:
          1)Door Height: 11-13/16 to 15-3/4 inches (300 to 400 mm). Door Weight: 4.4 to 33.1 lbs (2 to 15 kg).
          c.Components:
          1)Lift Mechanism, Mounting plate, Cover, and mounting screw.
          2)Hinges: for wood or aluminum doors and mounting plates.
          3)Opening Systems: Magnetic catches and striker plates.
          2.Wind: Small and compact flap door lifting system fixed to cabinet side/ For wooden doors. Adjustable spring strength. Opening: 85 to 94 degrees.
          a.Door Height: 8-21/32 to 23-5/8 inches (220 to 600 mm).
          b.Door Weight: 3.3 to 52.9 lbs (1.5 to 24 kg).
          ** NOTE TO SPECIFIER ** Delete one of the following two options not required.
          c.Soft close
          d.Push opening
 
          B.Drop Down Door Systems:
          ** NOTE TO SPECIFIER ** Delete door system not required.
          1.PACTA: With Smove system for single door fall flap.
          a.Hinge system for doors opening downwards without flap stays or cables.
          b.Fully-Open Position: Door and cabinet bottom panel align, creating a uniform and flat surface. Can also be used as a desk or writing surface.
          c.Soft Opening with Self close. For controlled and gradual motion.
          d.Cup Depth: 1/2 inch (13 mm).
          e.Opening: 90 degrees.
          f.Door Height: 11 to 16 inches (279 to 406 mm).
          g.Door Thickness: 5/8 to 1-7/64 inches (16 to 28 mm).
          h.Attachment to cabinet with in-line, snap-on mounting plate.
          i.Center Hinge: For doors wider than 30 inches (762 mm).
          ** NOTE TO SPECIFIER ** Delete cover options not required.
          j.Cover: White.
          k.Cover: Glossy White.
          l.Cover: Stainless steel.
          m.Cover: Gray.
          n.Cover: Champagne.
          o.Cover: Satin metal black.
          p.Cover: Glossy metal black.
          2.PACTA: With Push system for single door fall flap
          a.Hinge system for doors opening downwards without flap stays or cables.
          b.Fully-Open Position: Door and cabinet bottom panel align, creating a uniform and flat surface. Can also be used as a desk or writing surface.
          c.Soft Opening with Push to open. For handle-less doors.
          d.Cup Depth: 1/2 inch (13 mm)
          e.Opening: 90 degrees.
          f.Door Height: 11 to 16 inches (279 to 406 mm).
          g.Door Thickness: 5/8 to 1-7/64 inches (16 to 28 mm).
          h.Attachment to cabinet with in-line, snap-on mounting plate.
          i.Center Hinge: For doors wider than 30 inches (762 mm).
          ** NOTE TO SPECIFIER ** Delete cover options not required.
          j.Cover: White.
          k.Cover: Glossy White.
          l.Cover: Stainless steel.
          m.Cover: Gray.
          n.Cover: Champagne.
          o.Cover: Satin metal black.
          p.Cover: Glossy metal black.
          3.Vertical Sliding System: Mover Flat. Downward sliding system enabling the door to be held in any position.
          ** NOTE TO SPECIFIER ** Delete door width options not required.
          a.Door Width: 35-7/16 inches (900 mm).
          b.Door Width: 47-7/32 inches (1200 mm).
          c.Door Width: 71-1/16 inches (1800 mm).
          d.Door Width: 94-1/2 inches (2400 mm).
          e.Door Height: 18-7/8 to 24-3/4 inch (480 to 628 mm).
          f.Thickness of Cabinet Side: 3/4 inch (19 mm).
          g.Height Adjustment: Plus or minus 1/8 inches (3 mm).
          h.Components:
          1)Horizontal supporting profile and mounting supports.
          2)Pairs of runners with tie-rods and cams.
          ** NOTE TO SPECIFIER ** For doors 71-1/16inches (1800 mm) or greater. Delete if not required.
          3)Sliding profile for central panel with bumpers and hooks to mount the door onto the system.
          ** NOTE TO SPECIFIER ** Delete article if not required or delete paragraphs not required.
 
          2.5FURNITURE ACCESSORIES
 
          A.Excessories: Drawer storage.
          ** NOTE TO SPECIFIER ** Delete tray paragraphs not required and tray options not required.
          1.Imitation Leather Trays:
          a.Dimensions (DxWxH): 14.17 x 5.90 x 2 inches (360 x 150 x 50 mm)
          b.Dimensions (DxWxH): 16.14 x 5.90 x 2 inches (410 x 150 x 50 mm)
          c.Internal Dividers: One.
          d.Internal Dividers: Three.
          e.Internal dividers: Four.
          f.Internal Dividers: Five.
          g.Ring-holder tray.
          h.Earring holder tray.
          i.Earring and ring-holder tray.
          j.Watch holder tray.
          k.Finish: Moka Brown.
          l.Finish: Elephant Grey.
          m.Finish: Olive Grey.
          n.Finish: Taupe Brown.
          o.Finish: Tobacco Brown.
          p.Finish: Toffee White.
          2.Genuine Leather Trays:
          a.Dimensions (DxWxH): 11.22 x 5.04 x 2.16 inches (285 x 128 x 55 mm)
          b.Removable Internal Dividers: One.
          c.Earring and ring-holder tray.
          d.Ring holder tray.
          e.Watch holder tray.
          f.Finish: Moka Brown.
          g.Finish: Elephant Grey.
          h.Finish: Flax Grey.
          i.Finish: Turtle-Dove Grey.
          j.Finish: Mink Brown.
          k.Finish: Racing Green Brown.
          l.Finish: Khaki White.
          3.Imitation Leather Drawer Inserts:
          a.Dimensions (DxWxH): 14.17 x 5.90 x 2 inches (360 x 150 x 50 mm)
          b.Dimensions (DxWxH): 16.14 x 5.90 x 2 inches (410 x 150 x 50 mm)
          c.Wenge-Dyed Finish:
          1)Bottom only.
          2)Ring holder.
          3)Storage Dividers: 3.
          4)Earring holder.
          5)Watch holder.
          d.Walnut-Dyed Finish:
          1)Storage Dividers: 3.
          2)Bottom only.
          3)Ring holder.
          4)Earring holder.
          5)Watch holder.
          6)Bottom for drawers, shelves, and metal shoe racks.
          7)Drawer bottom with 3 dividers.
          e.Color: Moka Brown.
          f.Color: Elephant Grey.
          g.Color: Olive Grey.
          h.Color: Taupe Brown.
          i.Color: Tobacco Brown.
          j.Color: Toffee White.
 
          B.Excessories: Hanger systems.
          1.Hangers: Material: Beech. Finish: Wenge.
          a.Hook Material: Die-cast coated with epoxy-based powder.
          b.Hook Finish: Metal grey brown.
          ** NOTE TO SPECIFIER ** Delete hanger options and color options not required.
          c.Women's Suit Hanger:
          1)External Dimensions: 15-3/4 x 11-17/32 inches (400 x 293 mm).
          d.Women's Suit Hanger: Genuine leather insert.
          1)External Dimensions: 15-3/4 x 11-17/32 inches (400 x 293 mm).
          e.Men's Suit Hanger:
          1)External Dimensions: 17-23/32 x 10-1/8 inches(450 x 257 mm).
          f.Men's Suit Hanger: Genuine leather insert.
          1)External Dimensions: 17-23/32 x 10-1/8 inches(450 x 257 mm).
          g.Skirt Hanger:
          1)External Dimensions: 15-23/64 x 7-7/8 inches (390 x 200 mm).
          h.Skirt hanger: Genuine leather insert.
          1)External Dimensions: 15-23/64 x 7-7/8 inches (390 x 200 mm).
          i.Trousers Hanger:
          1)External dimensions: 15-23/64 x 6-11/16 inches (390 x 170 mm).
          j.Trousers hanger. Genuine leather insert.
          1)External dimensions: 15-23/64 x 6-11/16 inches (390 x 170 mm).
          k.Color: Moka Brown.
          l.Color: Elephant Grey.
          m.Color: Flax Grey.
          n.Color: Turtle-Dove Grey.
          o.Color: Mink Brown.
          p.Color: Racing Green Brown.
          q.Color: Khaki White.
          2.Hanging Elements:
          ** NOTE TO SPECIFIER ** Delete hanger options and color options not required.
          a.Bags Hanger:
          1)External Dimensions: 3-27/32 x 7-9/32 inches
          2)External Dimensions: 5-29/32 x 7-9/32 inches (98x185 mm)
          b.Scarves and Headscarves Hanger:
          1)External Dimensions: 5-29/32 x 9-21/32 inches (150x245 mm)
          c.Tie and Belt Hanger. Genuine leather support:
          1)External Dimensions: 5-11/16 x 6-1/8 inches (68x156 mm)
          d.Color: Moka Brown.
          e.Color: Elephant Grey.
          f.Color: Flax Grey.
          g.Color: Turtle-Dove Grey.
          h.Color: Mink Brown.
          i.Color: Racing Green Brown.
          3.Hanger Rods, Hanger Rods with Hook, and Tie Hanger Rods:
          a.Material: Beech. Finish: Wenge.
          b.Hook Material: Die-cast, coated with epoxy-based powder.
          c.Hook Finish: Metal grey brown.
          ** NOTE TO SPECIFIER ** Delete hanger rod options and color options not required.
          d.Hanger Rod:
          1)Dimensions: 33-1/16 inches (840 mm).
          e.Hanger Rod with Genuine Leather Sleeve:
          1)Dimensions: 33-1/16 inches (840 mm).
          f.Hanger Rod with Hook:
          1)Dimensions: 38-3/16 inches (970 mm).
          g.Hanger Rod with Hook and Genuine Leather Sleeve:
          1)Dimensions: 38-3/16 inches (970 mm).
          h.Tie Hanger Rod with Genuine Leather Supports:
          1)Dimensions: 34-1/16 inches (865 mm).
          i.Color: Moka Brown.
          j.Color: Elephant Grey.
          k.Color: Flax Grey.
          l.Color: Turtle-Dove Grey.
          m.Color: Mink Brown.
          n.Color: Racing Green Brown.
          o.Color: Khaki White.
          4.Hanger Rail: Material: Die-cast aluminum.
          ** NOTE TO SPECIFIER ** Delete hanger options and finish option not required.
          a.Hanger rail for clothes with supports, for wooden shelf.
          1)End supports for hanger rail.
          2)Centre support for hanger rail.
          3)Length: 39-3/8 inches (1000 mm).
          4)Length: 59-1/16 inches (1500 mm).
          b.Swivel hanger fixed under the shelf.
          1)Material: Steel.
          2)Finish: Nickel.
          c.Pull-out hanger. Cap in nickel finish.
          1)Material: Steel.
          2)Finish: Nickel.
          d.Pull-out hanger. Cap in metal grey brown finish.
          1)Material: Steel.
          2)Finish: Nickel.
          e.Finish: Metal grey brown.
          f.Finish: Nickel.
 
          C.Excessories: Protect.
          1.Coat-holder bag. Material: 100 percent cotton.
          a.External Dimensions:
          1)Folded: 38-3/16 inches (970 mm)
          2)Loose: 47-1/4 inch (1200 mm).
          ** NOTE TO SPECIFIER ** Delete color options not required.
          b.Color: Stoneware grey.
          c.Color: Brick brown.
          d.Color: Mint green.
 
          D.Excessories: Contain. Trays and boxes made of fabric.
          ** NOTE TO SPECIFIER ** Delete trays and boxes not required and box sizes not required.
          1.Trays:
          a.Dimension (LxDxH): 13-3/4 x 15-3/4 x 3-5/32 inches (350 x 400 x 80 mm).
          b.Dimension (LxDxH): 13-3/4 x 15-3/4 x 4-23/32 inches (350 x 400 x 120 mm).
          2.Trays with tab made of imitation leather:
          a.Dimension (LxDxH): 13-3/4 x 15-3/4 x 3-5/32 inches (350 x 400 x 80 mm).
          b.Dimension (LxDxH): 13-3/4 x 15-3/4 x 4-23/32 inches (350 x 400 x 120 mm).
          3.Trays with tab and frontal made of imitation leather
          a.Dimension (LxDxH): 13-3/4 x 15-3/4 x 3-5/32 inches (350 x 400 x 80 mm).
          b.Dimension (LxDxH): 13-3/4 x 15-3/4 x 4-23/32 inches (350 x 400 x 120 mm).
          4.Boxes:
          a.Dimensions (LxDxH): 9-27/32 x 18-5/16 x 10 inches (250 x 465 x 255 mm).
          b.Lid Dimensions (LxDxH): 10-7/32 x 18-7/8 x 2 inches (260 x 480 x 50 mm).
          5.Boxes:
          a.Dimensions (LxDxH): 15-5/16 x 18-5/16 x 4-15/16 inches (390 x 465 x 125 mm).
          b.Lid Dimensions (LxDxH): 15-3/4 x 18-7/8 x 2 inches (400 x 480 x 50 mm).
          6.Boxes:
          a.Dimensions (LxDxH): 15-5/16 x 18-5/16 x 10 inches (390 x 465 x 255 mm).
          b.Lid Dimensions (LxDxH): 15-3/4 x 18-7/8 x 2 inches (400 x 480 x 50 mm).
          7.Boxes with Tabs Made of Imitation Leather:
          a.Dimensions (LxDxH): 9-27/32 x 18-5/16 x 10 inches (250 x 465 x 255 mm).
          b.Lid Dimensions (LxDxH): 10-7/32 x 18-7/8 x 2 inches (260 x 480 x 50 mm).
          8.Boxes with Tabs Made of Imitation Leather:
          a.Dimensions (LxDxH): 15-5/16 x 18-5/16 x 4-15/16 inches (390 x 465 x 125 mm).
          b.Lid Dimensions (LxDxH): 15-3/4 x 18-7/8 x 2 inches (400 x 480 x 50 mm).
          9.Boxes with Tab Made of Imitation Leather:
          a.Dimensions (LxDxH): 15-5/16 x 18-5/16 x 10 inches (390 x 465 x 255 mm).
          b.Lid Dimensions (LxDxH): 15-3/4 x 18-7/8 x 2 inches (400 x 480 x 50 mm).
          ** NOTE TO SPECIFIER ** Delete color options not required.
          10.Color: Tasmania grey.
          11.Color: Flax grey.
          12.Color: Brown.
          13.Color: Sage green.
          14.Color: Pumpkin orange.
          15.Color: Denim blue.
          16.Color: Bitter red.
 
          E.Excessories: Pull-Out.
          ** NOTE TO SPECIFIER ** Delete drawer options not required.
          1.Aluminum 3-Sided Drawers with Various Fronts.
          ** NOTE TO SPECIFIER ** Delete drawer type not required and drawer front options not required.
          a.Wooden Frontal:
          1)Maximum. Drawer Width: 59-1/16 inches (1500 mm).
          2)Material: Aluminum coated with epoxy-based powder.
          a)Finish: Metal grey brown.
          3)Aluminum 3-sided drawer H 52.
          a)Profile height: 2 inches (52 mm).
          4)Aluminum 3-sided drawer H 78.
          a)Profile height: 3-1/16 inch (78 mm).
          5)Aluminum 3-sided drawer H 128.
          a)Profile height: 5-1/32 inches (128 mm).
          b.Glass Frontal:
          1)Max. Drawer Width: 59-1/16 inches (1500 mm).
          2)Material: Aluminum coated with epoxy-based powder.
          3)Finish: Metal grey brown.
          4)Aluminum 3-sided drawer H 52.
          a)Profile height: 2 inches (52 mm).
          5)Aluminum 3-sided drawer H 78.
          a)Profile height: 3-1/16 inch (78 mm).
          6)Aluminum 3-sided drawer H 128.
          a)Profile height: 5-1/32 inches (128 mm).
          2.Aluminum 4-Sided Drawers.
          a.Maximum. Drawer Width: 59-1/16 inches (1500 mm).
          b.Material: Aluminum coated with epoxy-based powder.
          1)Finish: Metal grey brown.
          ** NOTE TO SPECIFIER ** Delete drawer height options not required.
          2)Profile height: 2 inches (52 mm).
          3)Profile height: 3-1/16 inch (78 mm).
          4)Profile height: 5-1/32 inches (128 mm).
          3.Trousers Hangers and/or Skirt Hanger Drawers:
          a.Material: Aluminum coated with epoxy-based powder.
          b.Finish: Metal grey brown.
          c.Soft trim on upper surface to hold trousers in place.
          d.Rail supplied with nylon supports for easy location and sliding on the frame.
          e.Drawer Lengths: 19-11/16 inches (500 mm).
          f.Drawer Type: Four-Sided Drawers.
          ** NOTE TO SPECIFIER ** Delete runner length options not required.
          1)Runner Length: 13-3/4 inches (350 mm). Drawer Depth: 15-11/32 inches (390 mm).
          a)Rod Length: 11-1/16 inch (281 mm).
          2)Runner Length: 15-3/4 inches (400 mm). Drawer Depth: 17-5/16 inches (440 mm).
          a)Rod Length: 13-1/32 inches (331 mm).
          3)Runner Length: 17-23/32 inches (450 mm). Drawer Depth: 19-9/32 inches (490 mm).
          a)Rod Length: 15 inches (381 mm).
          4)Runner Length: 18-1/2 inch (470 mm). Drawer Depth: 20-1/16 inch (510 mm).
          a)Rod Length: 15-25/32 inches (401 mm).
          g.Drawer Type: Three-Sided Drawers:
          ** NOTE TO SPECIFIER ** Delete front and runner length options not required.
          1)Front: Wooden.
          2)Front: Glass.
          3)Runner Length: 13-3/4 inches (350 mm). Drawer Depth: 15-11/32 inches (390 mm).
          a)Rod Length: 12-3/32 inches (307 mm).
          4)Runner Length: 15-3/4 inches (400 mm). Drawer Depth: 17-5/16 inches (440 mm).
          a)Rod Length: 14-1/16 inches (357 mm).
          5)Runner Length: 17-23/32 inches (450 mm). Drawer Depth: 19-9/32 inches (490 mm).
          a)Rod Length: 16-1/32 inches (407 mm).
          6)Runner Length: 18-1/2 inch (470 mm). Drawer Depth: 20-1/16 inch (510 mm).
          a)Rod Length: 16-13/16 inches (427 mm).
          4.Bed Linen Storage for Drawer:
          a.Containers: Quilted fabric in Tasmania grey, easily removable from frame; Velcro fastenings. Custom-made according to drawer dimensions:
          b.Structure Material: Aluminum coated with epoxy-based powder.
          c.Finish: Metal grey brown.
          ** NOTE TO SPECIFIER ** Delete drawer width and depth options not required.
          d.Drawer Width: Up to 27-9/16 inches (700 mm): Oner container.
          e.Drawer Width: 27-9/16 inches (700 mm) and Larger: Two containers.
          f.Drawer Depth: 15-11/32 inches (390 mm).
          g.Drawer Depth: 17-5/16 inches (440 mm).
          h.Drawer Depth: 19-9/32 inches (490 mm).
          i.Drawer Depth: 20-5/32 inches (510 mm).
          5.Wired Shoe Rack for Drawer:
          a.Material: Aluminum coated with epoxy-based powder.
          1)Finish: Metal grey brown.
          b.Made in a single piece to suit drawer size.
          c.Holds two rows of shoes
          d.Maximum Width: 47-1/4 inches (1200 mm).
          ** NOTE TO SPECIFIER ** Delete drawer type and drawer width, and depth options not required.
          e.Drawer Type: Four sided.
          f.Drawer Type: Three sided. Wood or glass front.
          g.Drawer Depth: 19-9/32 inches (490 mm).
          h.Drawer Depth: 20-5/32 inches (510 mm).
          6.Metal Shoe Rack for Drawer:
          a.Material: Coated perforated metal sheet.
          1)Finish: Metal grey brown.
          b.Made in a single piece to suit drawer size.
          c.Holds two rows of shoes.
          d.Maximum Width: 59-1/16 inches (1500 mm).
          ** NOTE TO SPECIFIER ** Delete drawer type and drawer width, and depth options not required.
          e.Drawer Type: Four sided.
          f.Drawer Type: Three sided. Wood or glass front.
          g.Drawer Depth: 19-9/32 inches (490 mm).
          h.Drawer Depth: 20-5/32 inches (510 mm).
          i.Imitation leather inserts.
 
          F.Excessories: Shelves.
          1.Shelves with aluminum frame.
          2.Profile Height: 1-13/32 (36 mm).
          3.Material: Aluminum coated with epoxy-based powder.
          4.Finish: Metal grey brown.
          5.Maximum Width: 59-1/16 inches (1500 mm).
          6.Fixing: Side fixed with slide and lock device.
          7.Gasket to hold glass inlay in position. Glass not supplied.
          8.Custom Made to Order:
          a.Width: ___ inches (___ mm).
          b.Length: ___ inches (___ mm).
          c.Depth: ___ inches (___ mm).
          9.Can be supplied with 2700K/4000K Dual color, 24V integral LED light and with supports for clothes hanging rails.
          a.Consumption: 13W/M
 
          G.Display Storage Systems:
          ** NOTE TO SPECIFIER ** Delete pine storage systems not required.
          1.Pin Wine: Maximum weight carried by one pair: 7.72 lbs (3.5 kg).
          a.Post Components:
          1)Anchor bolt.
          2)Gasket.
          3)Bracket.
          4)Connecting item.
          5)Cap.
          b.Labels: Information labels. Assemble to posts.
          c.Profiles: Surface-mounted or recessed into wood panels.
          ** NOTE TO SPECIFIER ** Delete profile length and finish options not required.
          d.Profile Length: 39-3/8 inches (1 m).
          e.Profile Length: 78-3/4 inches (2 m).
          f.Profile Length: 118-1/8 inches (3 m).
          g.Finish: Aluminum.
          h.Finish: Titanium.
          2.Pin Knife: Maximum weight carried by one pair: 33.07 lbs (15 kg).
          a.Post Components:
          1)Anchor bolt:
          2)Gasket:
          3)Bracket:
          4)Connecting item:
          5)Cap:
          b.Profiles: Surface-mounted or recessed into wood panels.
          ** NOTE TO SPECIFIER ** Delete profile length and finish options not required.
          c.Profile Length: 39-3/8 inches (1 m).
          d.Profile Length: 78-3/4 inches (2 m).
          e.Profile Length: 118-1/8 inches (3 m).
          f.Finish: Aluminum.
          g.Finish: Titanium.
          3.Pin Shelf: Maximum weight carried by one pair: 16.53 lbs (7.5 kg).
          a.Post Components.
          1)Anchor bolt.
          2)Gasket.
          3)Bracket:
          4)O-ring.
          b.Profiles: Surface-mounted or recessed into wood panels.
          ** NOTE TO SPECIFIER ** Delete profile length and finish options not required.
          c.Profile Length: 39-3/8 inches (1 m).
          d.Profile Length: 78-3/4 inches (2 m).
          e.Profile Length: 118-1/8 inches (3 m).
          f.Finish: Aluminum.
          g.Finish: Titanium.
          h.Maximum shelf depth: 6-5/16 inches (160 mm).
          4.Pin Hang: Maximum weight carried by one pair: 22 lbs (10 kg).
          a.Post Components:
          1)Anchor bolt.
          2)Gasket.
          3)Bracket.
          4)Connecting item.
          5)Cap.
          b.Profiles: Surface-mounted or recessed into wood panels.
          ** NOTE TO SPECIFIER ** Delete profile length and finish options not required.
          c.Profile Length: 39-3/8 inches (1 m).
          d.Profile Length: 78-3/4 inches (2 m).
          e.Profile Length: 118-1/8 inches (3 m).
          f.Finish: Aluminum.
          g.Finish: Titanium.
          ** NOTE TO SPECIFIER ** Delete article if not required or delete door paragraphs not required.
 
          2.6SLIDING SYSTEMS
 
          A.Coplanar Systems:
          ** NOTE TO SPECIFIER ** Delete slider paragraphs not required and slider options not required.
          1.Slider S10:
          a.Wooden Cabinet Type: Wall cabinet.
          b.Wooden Cabinet Type: Base cabinet.
          c.Version: Single door right.
          d.Version: Single door left.
          e.Version: Two doors.
          f.Version: Two doors, Reverso.
          g.Single-piece sliding track.
          h.Innovative suspended slider with double horizontal wheels.
          i.Soft opening and soft close feature.
          j.Full adjustment of the doors.
          k.Weight Capacity per Door: 22 lbs (10 kg).
          l.Width of Door: 17-11/16 to 47-1/4 inches (450 to 1200 mm).
          m.Height of Door: 31-1/2 inches (800 mm).
          n.Thickness of Door: 5/8 to 1-3/16 inches (16 mm to 30 mm).
          o.Maximum Door Thickness with Handle: 1-9/16 inches (40 mm).
          p.Minimum Distance of Handle from Edge of Door: 3/8 inches (10 mm).
          q.Door Height Adjustment: Plus or minus 3/16 inches (Plus or minus 5.0 mm).
          r.Door Side Adjustment: Plus or minus 1/8 inches (Plus or minus 2.5 mm).
          s.Door Depth Adjustment:
          1)Wall: Plus or minus 1/16 inch (Plus or minus 2.0 mm).
          2)Base: Plus or minus 1/8 inches (Plus or minus 2.5 mm).
          t.Available also in motorized version only upon request as a custom order.
          2.Slider S20:
          a.Wooden Cabinet Type: Wall cabinet. Wood or glass aluminum frame doors.
          b.Wooden Cabinet Type: Base cabinet. Wood or glass aluminum frame doors.
          c.Version: Single door right.
          d.Version: Single door left.
          e.Version: Two doors.
          f.Version: Two doors, Reverso.
          g.Version: Three doors.
          h.Weight Capacity per Door: 44 lbs (20 kg).
          i.Width of Door: 23-5/8 to 59 inches (600 to 1500 mm).
          j.Width of Door: 47-7/32 inch (1200 mm).
          k.Thickness of Door: 3/4 to 1-3/16 (19 to 30 mm).
          l.Maximum Door Thickness with Handle: 1-3/4 inches (45 mm).
          m.Minimum Distance of Handle from Edge of Door: 3/8 inches (10 mm).
          n.Door Vertical Adjustment: Plus or minus 3/16 inches (Plus or minus 4.5 mm).
          o.Door Horizontal Adjustment: Plus or minus 1/8 inches (Plus or minus 3 mm).
          p.Push release version kit available.
          q.Available also in motorized version only upon request as a custom order.
          3.Slider M35 Top: Coplanar sliding system for wooden cabinets.
          a.Version: Top Reverso that enables doors to be opened in opposite direction.
          b.Version: Slider M35 Top Step, a system that enables doors to be opened when they are separated by a central compartment.
          c.Version: Slider M35 Top One, a system for opening of a single door.
          d.Version: Slider M35 Top Power, a motorized system for opening the door.
          e.Weight per Door: 77 lbs (35 kg).
          f.Width for Door: 24 to 59 inches (600 to 1500 mm).
          g.Height of Door: 47-1/4 to 70-7/8 inches (1200 to 1800 mm).
          h.Door Thickness with Handle: 23/32 to 1-9/16inch (18 to 40 mm).
          i.Soft closing movement while opening and closing.
          j.Door Vertical Adjustment: Plus or minus 3/16 inches (Plus or minus 5 mm).
          k.Door Horizontal Adjustment: Plus or minus 1/8 inches (Plus or minus 3.5 mm).
          l.Front Adjustment:
          1)Upper: Plus or minus 1/8 inches (Plus or minus 3 mm).
          2)Lower: Plus or minus 5/64 inches (Plus or minus 2 mm).
          4.Slider M50+: For tall double door cabinets with soft opening and closing feature with magnetic technology. For wood or glass with aluminum frame doors.
          a.Version: Single door right.
          b.Version: Single door left.
          c.Version: Two doors.
          d.Version: Two doors, Reverso.
          e.Version: Three doors.
          f.Weight Capacity per Door: 110 lbs (50 Kg).
          g.Width of Door: 23-5/8 to 78-3/4 inches (600 to 2000 mm).
          h.Height of Door from Floor Level: 11/16 inches (17 mm).
          i.Thickness of Door: 3/4 to 1-3/16 inches (19 to 30 mm).
          j.Maximum Door Thickness with Handle: 1-3/4 inches (45 mm).
          k.Door Height Adjustment: Plus or minus 3/16 inches (Plus or minus 5 mm).
          l.Door Side Adjustment: Plus or minus 1/8 inches (3.5 mm).
          m.Available also in motorized version with max. weight door of 77 lbs (35 Kg) only upon request as a custom order.
          n.Mechanisms:
          1)Overall Lengths: 47-7/32 to 63 inches (1199 to 1599 mm).
          a)Max. door height: 95-1/2 inches (2400 mm).
          b)Adaptable to cabinets up to 4 inch (100 mm) wider than the track.
          2)Overall Lengths: 63 to 78-3/4 inches (1600 to 1999 mm).
          a)Max. door height: 106-19/64 inches (2700 mm).
          b)Adaptable to cabinets up to 7-7/8 inches (200 mm) wider than the track.
          3)Overall lengths between 78-3/4 to 110-3/16 inches (2000 to 2799 mm)
          a)Door Height: 118-1/8 inches (3000 mm)
          b)Adaptable to cabinets up to 7-7/8 inches (200 mm) wider than the track.
          5.Slider L70: For tall double door cabinets with soft door opening and soft closing feature with magnetic technology-heavy duty. Wood or glass with aluminum frame doors.
          a.Version: Single door right.
          b.Version: Single door left.
          c.Version: Two doors.
          d.Version: Two doors, Reverso.
          e.Version: Three doors.
          f.Weight Capacity per Door: 154 lbs (70 kg).
          g.Width of Door: 31-1/2 to 78-3/4 inches (800 to 2000 mm).
          h.Height of Door: 118-1/8 inches (3000 mm).
          i.Height of Door from Floor Level: 1-11/32 inches (33 mm).
          j.Thickness of Door: 3/4 to 1-3/4 inches (19 to 45 mm)
          k.Door Height Adjustment: Plus or minus 3/16 inches (Plus or minus 5 mm).
          l.Door Side Adjustment: Plus or minus 1/8 inches (3.5 mm).
          m.For cabinets with dimensions up to 7-7/8 inches (200 mm) longer than the mechanism
          n.Front levelling feet.
 
          B.Pocket Door Systems:
          1.Exedra Pocket Doors: Smooth lateral assisted positive opening and cushioned soft-close movements, controlled by a safety device. Smooth, fluent, uniform, and noiseless movement, regardless of door insertion speed.
          a.Aluminum Profiles: 6060T5 alloy. Finish: Silver anodized.
          b.Components: Plastic, steel, and zinc alloy.
          c.Maximum Door Weight: 66 lbs (30 Kg).
          d.Thickness: 3/4 to 1-3/16 inches (19 to 30 mm).
          e.Width: 15-3/4 to 35-7/16 inches (400 to 900 mm).
          f.Height:
          1)Minimum: 51-1/16 inches (1333 mm).
          2)Minimum with Roller Kit: 53-1/2 inch (1359 mm).
          3)Maximum: 99-5/8 inches (2530 mm).
          g.Door Vertical Adjustment: Plus 5/32 inch (4 mm), minus 1/32 inch (1 mm).
          h.Door Horizontal Adjustment: Plus or minus 5/64 inches (Plus or minus 2 mm).
          i.Door Front Adjustment: Plus or minus 5/32 inch (4 mm).
          j.Assisted door extraction movement.
          k.Soft closing buffer with a linear magnetic damper.
          ** NOTE TO SPECIFIER ** Delete material not required.
          l.Material: Wood or derivatives.
          m.Material: Metal framed glass.
          n.Standard Projection of Door in Open Position: 4-3/16 inch (107 mm) when allowed.
          o.Space Below Door: 3/16inches (5 mm).
 
          C.Concertina Doors Sliding Systems:
          1.Components:
          ** NOTE TO SPECIFIER ** Delete track length and track color options not required.
          a.Track Length: 23-7/32 inches (590 mm).
          b.Track Length: 34-5/8 inches (880 mm).
          c.Track Length: 46-1/2 inches (1180 mm).
          d.Track Color: White:
          e.Track Color: Black:
          f.Track Color: Grey:
          g.Track Color: Beige:
          h.Hinge for sliding block.
          i.Central hinge.
          j.Hinge for aluminum-framed doors.
          k.Adhesive finger-protection strip.
          l.Long sliding block for aluminum-framed doors.
          m.Locating device for door.
          n.Sliding block.
          ** NOTE TO SPECIFIER ** Delete article if not required or delete paragraphs not required.
 
          2.7DAMPERS AND RELEASE DEVICES
 
          A.Dampers, External:
          ** NOTE TO SPECIFIER ** Delete external dampers not required. And delete damper options not required.
          1.Smove Universal Smoveholder: Damper device used to soften the closing action of any furniture door with concealed hinges. Used with all brands of hinges.
          a.Adapter: Screw fixed.
          ** NOTE TO SPECIFIER ** Delete overlay option not required.
          1)Full-overlay 9/16 inches (14 mm): Recess between 0 and 1/2 inches (0 and 12 mm).
          2)Half-overlay 25/32 inches (20 mm): Recess between 3/8 and 5/8 inches (10 and 16 mm).
          2.Smove D0S_SNG: System to soften the closing action of any door. Used with cruciform mounting plates. For light doors with two or more hinges.
          a.Adjustable decelerating system.
          b.Dampers for doors made with particularly light materials.
          c.Dampers for doors with two hinges.
          d.Dampers for doors with more than two hinges.
          e.Adapter: For use with cruciform mounting plates 1-7/16 x 1-1/4 inch (37 x 32 mm).
          1)Hinges with adapter height of 0.
          2)Hinges with adapter height of 5.
          3)Hinges with adapter height of 9.
          4)Hinges with adapter height of 17.
          3.Smove D0L_SNG: System to soften the closing action of any door; application on the top or bottom panel of the cabinet.
          a.With Stop Devices:
          1)For doors made with particularly light materials.
          2)For doors with two hinges.
          3)For doors with more than two hinges.
          b.Without Stop Devices:
          1)For doors made with particularly light materials.
          2)For doors with two hinges.
          3)For doors with more than two hinges.
          4.Smove recessed devices to soften closing action of any furniture door.
          a.Color: Grey.
          b.Color: Beige.
          c.For wood-based and aluminum framed doors over 63 inches (1600 mm) height.
          1)Dampers inserted opposite the hinges. It may be necessary to use two dampers, one to be inserted into the upper part and second into the lower part of cabinet side,
          2)Dampers inserted into center of the cabinets. It may be necessary to use two dampers, one to be inserted into the center of the top or the base panel of the cabinet.
          3)Dampers Inserted into the top or the base panel of the cabinet on the hinged side. It may be necessary to insert one device into the top and a second into the base panel of the cabinet.
          a)Drilling Distance from Cabinet Side: 1-1/16 inches (27 mm).
          4)Dampers inserted into the base panel of the cabinet on the hinged side.
          a)Drilling distance from the cabinet side:
          1)Hinges with arm 0 mm: 019/32 inches (15 mm) plus base height.
          2)Hinges with arm 5 mm: 25/32 inches (20 mm) plus base height.
          3)Hinges with arm 9 mm: 15/16 inches (24 mm) plus base height.
          d.For wood-based and aluminum framed doors 28-11/32 to 63 inches (720 to 1600 mm) height.
          1)Dampers inserted into the base panel of the cabinet on the hinged side.
          a)Drilling distance from the cabinet side:
          1)Hinges with arm 0 mm: 019/32 inches (15 mm) plus base height.
          2)Hinges with arm 5 mm: 25/32 inches (20 mm) plus base height.
          3)Hinges with arm 9 mm: 15/16 inches (24 mm) plus base height.
          ** NOTE TO SPECIFIER ** Delete adapters not required and adapter options not required.
          5.Adapters to be Screw Fixed to the Cabinet: Made of plastic.
          a.Color: Grey.
          b.Color: Beige.
          c.Longitudinal plastic adapter. Mounted with dowels.
          1)Without assembly stop device
          d.Cruciform plastic adapter. Mounted with wood screws.
          1)With assembly stop device.
          2)Drilling: 1-1/2 x 1-1/4 inches (37 x 32 mm).
          e.Cruciform plastic adapter.
          1)Mounted with wood screws.
          2)Mounted with Euroscrews
          3)Without assembly stop device.
          4)Drilling: 1-1/2 x 1-1/4 inches (37 x 32 mm).
          f.Cruciform plastic adapter. Mounted with wood screws.
          1)With assembly stop device.
          2)Drilling: 1-1/8 x 1-1/4 inches (37 x 32 mm).
          g.Cruciform plastic adapter. Mounted with wood screws.
          1)Without assembly stop device.
          2)Drilling: 1-1/8 x 1-1/4 inches (37 x 32 mm).
          h.Cruciform plastic adapter. Mounted with wood screws.
          1)With assembly stop device.
          2)Drilling: 3/8 x 1-1/4 inches (37 x 32 mm).
          i.Double cruciform plastic. Mounted with wood screws.
          1)With assembly stop device.
          2)Drilling: 7/32 x 1-1/4 inches (37 x 32 mm).
          j.Double cruciform plastic. Mounted with wood screws.
          1)Without assembly stop device
          2)Drilling: 7/32 x 1-1/4 inches (37 x 32 mm).
          6.Adapters to be Screw Fixed to the Cabinet: Made of die-cast.
          a.Longitudinal die-cast adapter. To be fixed with wood screws.
          1)Without assembly stop device.
          2)Cover caps to be ordered separately.
          3)Mounted with Euroscrews.
          b.Longitudinal die-cast adapter. To be fixed with wood screws.
          1)With assembly stop device.
          2)Cover caps to be ordered separately.
          3)Mounted with Euroscrews.
          7.Adapters with Double Sided Adhesive System: Made of plastic.
          a.Color: Grey.
          b.Color: Beige.
          c.Longitudinal plastic adapter. With assembly stop device.
          d.Longitudinal plastic adapter with additional fixing screw.
          1)Mounted with double sided adhesive system. For application with full overlay door.
          2)With assembly stop device.
          e.Longitudinal plastic adapter with additional fixing screw.
          1)Mounted with double sided adhesive system. For application with full and half overlay door.
          2)With assembly stop device.
          8.Adapter to be Mounted to Door with Screws: Made of die-cast.
          a.Longitudinal inclined die-cast adapter.
          1)Mounted with wood screws or Euroscrews.
          2)Without assembly stop device.
          3)Position near the center of the height of the door.
 
          B.Mechanical Push Dampers:
          1.With adhesive strip.
          ** NOTE TO SPECIFIER ** Delete color and screw fixed options not required.
          2.Color: Beige.
          3.Color: Grey.
          4.Screw Fixed: With assembly stop device.
          5.Screw Fixed: Without assembly stop device.
          6.Screw Fixed: Single adapter with depth and sideways adjustment and release device. With assembly stop device.
          7.Screw Fixed: Double adapter with depth and sideways adjustment and release devices. Without assembly stop device.
 
          C.Retaining Catches for Wooden Doors:
          ** NOTE TO SPECIFIER ** Delete color and retaining catch options not required.
          1.Color: Beige.
          2.Color: Grey.
          3.Retaining Catch: For wooden door. Knock-in.
          4.Retaining Catch: For wooden door and special assemblies. Knock-in.
          5.Retaining Catch: For wooden door. With assembly stop device. Screw-on.
          6.Retaining Catch: For wooden door. Without assembly stop device. Screw-on.
 
          D.Retaining Catches for Aluminum-Frame Doors:
          ** NOTE TO SPECIFIER ** Delete color and retaining catch options not required.
          1.Color: Beige.
          2.Color: Grey.
          3.Retaining catch for aluminum-frame. Door Width: 1-3/8 to 1-3/4 inches (35 to 45 mm).
          4.Retaining catch for aluminum-frame. Door Width: 11/16 to 1-3/8 inches (17 to 35 mm).
 
          E.Adapters:
          ** NOTE TO SPECIFIER ** Delete color and adapter options not required.
          1.Color: Beige.
          2.Color: Grey.
          3.Single adapter with assembly stop device.
          a.Drilling: 1/4 x 1-9/16 inches (6 x 40 mm).
          b.Drilling: 1/4 x 5/8 inches (6 x 16 mm).
          4.Single adapter without assembly stop device.
          a.Drilling: 1/4 x 1-9/16 inches (6 x 40 mm).
          b.Drilling: 1/4 x 5/8 inches (6 x 16 mm).
 
          F.Spacers and Insertion Tool for Retaining Catches:
          ** NOTE TO SPECIFIER ** Delete color and spacer options not required.
          1.Color: Beige.
          2.Color: Grey.
          3.Right Spacer: 3/16 (4.8 mm).
          4.Left Spacer: 3/16 (4.8 mm).
 
          G.Magnetic Push: Magnetic release devices and retaining catches.
          ** NOTE TO SPECIFIER ** Delete release device not required and delete supplementary release device if not required.
          1.Beige Release Device: Diameter: 0.39 inches (10 mm). Length: 1.57 inches (40 mm).
          a.Supplementary Release Device: Increases magnetic holding strength of DPM-series devices. Diameter: 0.39 inches (10 mm). Length: 1.57 inches (40 mm). Position the DPM at point of pressure on the door. Position the DPA at any point along opening edge of door.
          b.Beige spacer for inset door to be used together with release devices.
          2.Grey Release Device: Diameter: 0.39 inches (10 mm). Length: 1.57 inches (40 mm).
          a.Supplementary Release Device: Increases magnetic holding strength of DPM-series devices. Diameter: 0.39 inches (10 mm). Length: 1.57 inches (40 mm). Position the DPM at point of pressure on the door. Position the DPA at any point along opening edge of door.
          b.Grey spacer for inset door to be used together with release devices.
          ** NOTE TO SPECIFIER ** Delete retaining catch options not required.
          3.Retaining Catch: Insertion type. Diameter: 7/16 inch (11.5 mm) diameter
          4.Retaining Catch: With adhesive. 7/8 x 9/16 inch (20 x 14 mm).
          5.Retaining Catch: Adjustable magnetic. Diameter: 21/32 inches (16.6 mm)
          6.Adapters:
          ** NOTE TO SPECIFIER ** Delete adapter options not required.
          a.Beige plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 0.29 x 1.25 inch (7.5 x 32 mm ). Without assembly stop devices.
          b.Grey plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 0.29 x 1.25 inch (7.5 x 32 mm ). Without assembly stop devices.
          c.Beige plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 0.29 x 1.25 inch (7.5 x 32 mm ). Without assembly stop devices.
          d.Grey plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 0.29 x 1.25 inch (7.5 x 32 mm ). Without assembly stop devices.
          e.Beige plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 0.31 x .63 inch (8 x 16 mm ). Without assembly stop devices.
          f.Grey plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 0.31 x .63 inch (8 x 16 mm ). Without assembly stop devices.
          g.Beige plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 0.31 x 1.25 inch (8 x 32 mm ). Without assembly stop devices.
          h.Grey plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 0.31 x 1.25 inch (8 x 32 mm ). Without assembly stop devices.
          i.Beige plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 0.31 x 1.25 inch (8 x 32 mm ). Without assembly stop devices.
          j.Grey plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 0.31 x 1.25 inch (8 x 32 mm ). Without assembly stop devices.
          k.Beige adjustable plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 1.46 x 1.25 inch (37 x 32 mm ). Without assembly stop devices.
          l.Grey adjustable plastic adapter for release device. Fixed with wood screws.
          1)Drilling: 1.46 x 1.25 inch (37 x 32 mm ). Without assembly stop devices.
 
          PART 3EXECUTION
 
          3.1EXAMINATION
 
          A.Do not begin installation until substrates have been properly constructed and prepared.
 
          B.If substrate preparation is the responsibility of another installer, notify Architect in writing of unsatisfactory preparation before proceeding.
 
          3.2PREPARATION
 
          A.Clean surfaces thoroughly prior to installation.
 
          B.Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
 
          3.3INSTALLATION
 
          A.Install in accordance with manufacturer's instructions, approved submittals, and in proper relationship with adjacent construction.
 
          3.4FIELD QUALITY CONTROL
 
          A.Field Inspection: Coordinate field inspection in accordance with appropriate sections in Division 01.
          ** NOTE TO SPECIFIER ** Include if manufacturer provides field quality control with onsite personnel for instruction or supervision of product installation, application, erection, or construction. Delete if not required.
 
          B.Manufacturer's Services: Coordinate manufacturer's services in accordance with appropriate sections in Division 01.
 
          3.5CLEANING AND PROTECTION
 
          A.Clean products in accordance with the manufacturer's recommendations.
 
          B.Touch-up, repair or replace damaged products before Substantial Completion.
 
         
END OF SECTION