MasterFormat: 2014
Download this Hurricane Resistant Windows and Doors Specification for   WORD | WP | RTF | TEXT
Find over 500 more construction specifications | Arcat.com
         
CGI Windows and Doors, Inc.  Hurricane Resistant Windows and Doors
 
         
SECTION 08 57 00
 
         
HURRICANE RESISTANT WINDOWS AND DOORS
 
         
 
         
Copyright 2008 - 2011 ARCAT, Inc. - All rights reserved

          ** NOTE TO SPECIFIER ** CGI Windows and Doors, Inc. ; impact and hurricane resistant windows and doors.
This section is based on the products of CGI Windows and Doors, Inc. , which is located at:
3780 W. 104th St.
Hialeah, FL 33018
Toll Free Tel: 800-442-9042
Tel: 305-593-6590
Fax: 305-593-6592
Email: ocordova@cgiwindows.com
Web: http://www.cgiwindows.com

[ Click Here ] for additional information.
Since 1992, CGI has been creating high quality impact resistant windows and doors for the residential and commercial markets. CGI hurricane windows and doors can now be found in hotels, schools, office buildings, and in the finest and most elegant of homes.
CGI's line of impact windows and doors is manufactured in accordance with the most stringent impact standards in the country. Our impact products are produced by using only heavy commercial-grade aluminum, impact resistant laminated glass and the finest high-quality hardware.
CGI's products have easily passed the Miami-Dade County Large Missile test and have proven to withstand winds of nearly 300 mph and lead the industry in tested approved design pressures. Every impact resistant door and window that we manufacture offers unsurpassed impact resistance and hurricane protection.

 
          PART 1GENERAL
 
          1.1SECTION INCLUDES
          ** NOTE TO SPECIFIER ** Delete items below not required for project.
 
          A.Aluminum Windows: Impact-resistant aluminum windows, including aluminum extrusions, finish, glass, operating hardware, screens, internal sealants and weather stripping, for high velocity hurricane zone (HVHZ) construction. (Estate, Sentinel)
 
          B.Swing Doors: Impact-resistant aluminum swing doors, frames, sidelites, transoms, and structural mullions, including aluminum extrusions, finish, glass, door hardware, water-barrier thresholds, and weather strips, for high velocity hurricane zone (HVHZ) construction. (Estate, Sentinel)
 
          C.Sliding Doors: Impact-resistant aluminum sliding glass doors, frames, fixed panels, and structural mullions, including aluminum extrusions, finish, glass, door hardware, screens, water-barrier thresholds, and weather strips, for high velocity hurricane zone (HVHZ) construction. (Estate, Sentinel)
 
          1.2RELATED SECTIONS
          ** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
 
          A.Section 06 10 00 - Rough Carpentry.
 
          B.Section 07 91 26 - Joint Fillers.
 
          C.Section 08 83 13 - Mirrored Glass Glazing.
 
          1.3REFERENCES
          ** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
 
          A.American Architectural Manufacturers Association:
          1.AAMA 701/702: Pile weatherstripping and replaceable weatherseals.
          2.AAMA 2603: Organic coatings on aluminum.
          3.AAMA 2605: High-performance organic coatings on aluminum.
 
          B.American Society of Civil Engineers
          1.ASCE 7: Minimum Design Loads for Buildings and other Structures.
 
          C.American Society for Testing and Materials:
          1.ASTM B 221: Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes.
          2.ASTM E 283: Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen.
          3.ASTM E 330: Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference.
          4.ASTM E 331: Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference.
 
          D.Florida Building Code - Building, 2004 (FBC):
          1.Sections governing construction in a high-velocity wind zone (HVWZ).
          a.FBC 1620: HVWZ Wind Loads (Structural).
          b.FBC 2410: HVWZ General (Glass and Glazing).
          c.FBC 2411: HVWZ Windows, Doors, Glass and Glazing.
          2.Miami Dade County Test Application Standards (TAS) adopted by FBC:
          a.TAS 201-95.1: Impact Test Procedures.
          b.TAS 202-95.1: Criteria for Testing Impact Resistant Building Envelope Components (Uniform Static Air Pressure Method).
          c.TAS 203-95.1: Criteria for Testing Products Subject to Cyclic Wind Pressure Loading.
 
          1.4PERFORMANCE REQUIREMENTS
          ** NOTE TO SPECIFIER ** Delete if windows not required.
 
          A.Impact-Resistant Aluminum Window and Door Performance:
          1.Structural Test: ASTM E 330.
          2.Water Infiltration Resistance: ASTM ES47/E 331 and FBC TAS 202.
          3.Air Infiltration Resistance: ASTM E 283.
          4.Windborne Debris Impact Resistance: Pass large missile impact tests; Florida Building Code, FBC TAS 201.
          5.Hurricane Wind Pressure Resistance: After passing large missile impact test, pass cyclic pressure tests following FBC TAS 203.
 
          1.5SUBMITTALS
 
          A.Shop Drawings: Refer to Section 01 30 00 - Administrative Requirements for complete submittal procedures. Indicate elevations, locations, markings, quantities, material, head jamb and sill conditions, metal thickness, sizes, shapes, dimensions, finishes and wind pressures.
 
          B.Product Data: Provide detailed data on Manufacturers catalog data on each product to be used, including Miami Dade County Product Approval (NOA) and Florida Building Code (FBC) HVHZ Product Approval.
          ** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.
 
          C.Selection Samples: For each finish specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.
 
          1.6QUALITY ASSURANCE
 
          A.Manufacturer Qualifications: Not less than 10 years of experience in manufacturing impact-resistant aluminum windows and doors.
 
          B.Installer Qualifications: Skilled and experienced to install manufacturer's units of the types specified.
 
          1.7DELIVERY, STORAGE, AND HANDLING
 
          A.Store products in manufacturer's unopened packaging in a clean, dry area until ready for installation.
 
          B.Protect exposed metal and glass surfaces to prevent damage to finish.
 
          1.8WARRANTIES
 
          A.Warranty Period: Contact CGI Windows and Doors, Inc. for details on 10 year limited warranty.
          1.Structural, Hardware and Certain Finishes: 10 years.
          2.Stress Cracks on Glass: 1 year.
          3.Delamination on Laminated Glass Units: 5 years.
          4.Insulated Glass (sealed component): 10 years.
 
          PART 2PRODUCTS
 
          2.1MANUFACTURERS
 
          A.Acceptable Manufacturer: CGI Windows and Doors, Inc. , which is located at: 3780 W. 104th St.; Hialeah, FL 33018; Toll Free Tel: 800-442-9042 ; Tel: 305-593-6590; Fax: 305-593-6592; Email: ocordova@cgiwindows.com; Web: http://www.cgiwindows.com
          ** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
 
          B.Substitutions: Not permitted.
 
          C.Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.
          ** NOTE TO SPECIFIER ** Recognized by architects as a premier line of hurricane impact windows and doors, CGI Estate collection can be found in elegant homes, prestigious resorts, hotels, schools and office buildings. The collection combines best-in-class performance against hurricane force damage with architectural-grade quality, handcrafted details and superior engineering. Delete if not required.
 
          2.2ALUMINUM WINDOWS (ESTATE)
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          A.Fixed Windows: "Estate Collection" Series 238 Fixed Windows by CGI Windows and Doors, Inc.
          ** NOTE TO SPECIFIER ** Delete if not required.
          1.Fixed Window Types: Rectangular Fixed Windows; for example sizes and related design pressures refer to product approvals for latest results.
          a.Unit Size: 24 by 54 inches, 110 psf Positive, 195 psf Negative.
          b.Unit Size: 37 by 63 inches, 102.1 psf Positive, 111.3 psf Negative.
          c.Unit Size: 48 by 72 inches, 90 psf Positive, 90 psf Negative.
          ** NOTE TO SPECIFIER ** Delete if not required.
          2.Fixed Window Types: Designer Fixed Windows; for example sizes and related design pressures refer to product approvals for latest results.
          ** NOTE TO SPECIFIER ** Delete shapes not required.
          a.Designer Fixed Window Shapes: Half Circle.
          b.Designer Fixed Window Shapes: Arch Top/Eyebrow.
          c.Designer Fixed Window Shapes: Full Circle.
          d.Designer Fixed Window Shapes: Octagon.
          e.Designer Fixed Window Shapes: Hexagon.
          f.Designer Fixed Window Shapes: Chord.
          g.Designer Fixed Window Shapes: Tombstone.
          h.Designer Fixed Window Shapes: Trapezoid.
          i.Designer Fixed Window Shapes: Pentagon.
          j.Designer Fixed Window Shapes: Gothic Pentagon.
          k.Designer Fixed Window Shapes: Oval.
          l.Designer Fixed Window Shapes: Standard Colonial.
          m.Designer Fixed Window Shapes: Custom Colonial as indicated on Drawings.
          3.Air Infiltration Resistance: Air leakage no more than 0.07 cfm/sqft of glass area at pressure differential of 6.24 psf (air infiltration tests conducted at pressure differential of 1.57 psf may not be used to justify compliance).
          4.Water Infiltration Resistance: No water penetration at a static air pressure differential of 15 percent of positive design pressure with a maximum tested performance of 16.5 psf.
          5.Construction: Heavy extruded aluminum-alloy sections, precision cut and assembled with sealed, mitered, hairline joints.
          6.Member Wall Thicknesses:
          ** NOTE TO SPECIFIER ** Delete if not required.
          a.Rectangular Window Fixed Frames: At least 0.080 inch (2.03 mm).
          b.Designer Fixed Window Frames: At least 0.100 inch (2.54 mm).
          c.Rectangular Window Vents: At least 0.090 inch (2.29 mm).
          d.Designer Fixed Window Vents: At least 0.100 inch (2.54 mm).
          7.Frame Depth: Provide 0.50 (12.7 mm) inch flanges at perimeter frames.
          ** NOTE TO SPECIFIER ** Delete if not required.
          a.Rectangular Fixed Windows Frames: At least 2.075 inches (53 mm).
          b.Designer Fixed Window Frames: At least 2.085 (53 mm).
          8.Sightlines:
          ** NOTE TO SPECIFIER ** Delete if not required.
          a.Rectangular Fixed: Jambs, sill and head - 3.5 inches (89 mm).
          b.Designer Fixed: Jambs, sill and head - 3.25 inches (82.6 mm).
          9.Corner Construction:
          a.At Rectangular Fixed Window Frames: Assemble with sealed, mitered, hairline joints, made rigid by fastening with No. 10 stainless steel screws.
          b.At Fixed Window Frames: 4 stainless steel corner keys and 4 aluminum corner keys.
          c.At Designer Fixed Window Frames Construction: Welded corners with sealed hairline joints.
          10.Fixed Window Frame Construction: Use the same vent and frame extrusions as are used in casement and project-out Series 238 windows, but screw vent extrusion to frame extrusion at interior using No. 10 x 1 inch (25 mm) stainless steel sheet metal screws around entire window, spaced as required by NOA.
          a.Apply plastic caps matching color of finish to screw heads.
          b.Provide extruded aluminum decorative screw covers for rectangular fixed windows.
          11.Glazing Beads:
          ** NOTE TO SPECIFIER ** Delete type not required.
          a.Rectangular Fixed: Extruded aluminum snap-in design, with 0.500 inch (12.7 mm) glass bite for impact-resistant glazing at rectangular fixed windows.
          b.Designer Fixed: Extruded aluminum 0.75 inch (19 mm) by 0.75 inch (19 mm) x 0.125 inch (3.2 mm) wall thickness square tube glazing stop.
          12.Finishes: Uniform at all visible surfaces exterior and interior, vents open or shut.
          13.Factory Glazing:
          ** NOTE TO SPECIFIER ** Delete glazing type not required.
          a.Laminated Impact Resistant Glass Units: 7/16 inch (11 mm) thick (nominal) consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Outer and Inner Panes of Laminated Units: 3/16 inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed.
          b)Type: Tempered.
          ** NOTE TO SPECIFIER ** Delete tints not required.
          2)Tint in Outer Panes: None, clear.
          3)Tint in Outer Panes: Gray.
          4)Tint in Outer Panes: Bronze.
          5)Tint in Outer Panes: Green.
          6)Tint in Outer Panes: Blue.
          7)Tint in Outer Panes: High performance coating, Clear Low-E 366 on No. 2 surface.
          ** NOTE TO SPECIFIER ** Delete textures not required.
          8)Texture in Outer Panes: Standard, none, smooth.
          9)Texture in Outer Panes: Clear, Mist (Pattern C2).
          10)Texture in Outer Panes: Clear, Rain.
          ** NOTE TO SPECIFIER ** Second option below is only available with Low-E 366 coating. Delete types not required.
          11)Interlayer Type: 0.090 inch / 90 mil (2.2 mm) Saflex PVB.
          12)Interlayer Type: 0.090 inch / 90 mil (2.2 mm) Sentry Glass Plus.
          ** NOTE TO SPECIFIER ** Delete interlayer opacity not required.
          13)Interlayer Opacity: Standard, clear.
          14)Interlayer Opacity: White, translucent.
          15)Interlayer Opacity: Dark gray (turtle code).
          ** NOTE TO SPECIFIER ** Fill in blank below with tinting option. Tinting on inner panes only available with Clear Low-E 366 or textured coating on outer panes. Delete tints not required.
          16)Tint in Inner Panes: None, clear.
          17)Tint in Inner Panes: __________.
          ** NOTE TO SPECIFIER ** Delete if not required.
          b.Insulated Laminated Impact Resistant Glass Units: 3/4 inch (19 mm) thick (nominal) consisting of a sacrificial exterior lite, air space and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior Sacrificial Lites/Panes: 1/8 Inch (3.2 mm) tempered.
          ** NOTE TO SPECIFIER ** Delete tints not required.
          2)Tint in Sacrificial Lites/Panes: None, clear.
          3)Tint in Sacrificial Lites/Panes: Gray.
          4)Tint in Sacrificial Lites/Panes: Bronze.
          5)Tint in Sacrificial Lites/Panes: Green.
          6)Tint in Sacrificial Lites/Panes: Blue.
          7)Tint in Sacrificial Lites/Panes: High performance coating, Clear Low-E 366 on No. 2 surface.
          ** NOTE TO SPECIFIER ** Delete textures not required.
          8)Texture in Outer Panes: Standard, none, smooth.
          9)Texture in Outer Panes: Clear, Mist (Pattern C2).
          10)Texture in Outer Panes: Clear, Rain.
          11)Airspace: 1/4 inch (6 mm) minimum, Argon filled air space.
          12)Laminated Units: Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          a)Outer and Inner Panes of Laminated Units: 1/8 inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          1)Type: Annealed.
          2)Type: Tempered.
          ** NOTE TO SPECIFIER ** Fill in blank below with tinting option. Tinting on inner panes only available with Clear Low-E 366 or textured coating on outer panes. Delete tints not required.
          b)Tinting in Outer Pane: None, clear.
          c)Tint in Inner Panes: __________.
          ** NOTE TO SPECIFIER ** Additional and upgraded construction. Muntins not available with insulated glass. Delete items not required.
          14.Window Features:
          a.Raised profile muntins.
          b.Muntins: 3.5 inch (89 mm) muntins at rectangular fixed windows.
          c.Extruded double applied raised profile 1 inch (25.4 mm)
          d.Glazing Beads: Ogee glazing bead profile (colonial) at rectangular fixed windows.
          e.Glazing Beads: Square glazing bead profile (contemporary) at rectangular fixed windows..
          f.Standards: Miami Dade County NOA (Notices of Acceptance).
          g.Aluminum Alloy and Temper: AA 6063-T5 and T6 temper.
          h.Glazing Beads: Square tube glazing stops at Designer fixed windows.
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          B.Fixed Windows: "Estate Collection"Series 410 Rectangular Fixed Windows by CGI Windows and Doors, Inc.
          1.Rectangular Fixed Windows: For example sizes and related design pressures, refer to product approvals for latest results.
          a.Large Missile Impact:
          1)Unit Size: 42 by 72 inches, 133 psf Pos, 150 psf Neg.
          2)Unit Size: 60 by 96 inches, 103.6 psf Pos, 103.6 psf Neg.
          3)Unit Size: 72 by 120 inches, 75 psf Pos, 75 psf Neg.
          b.Small Missile Impact:
          1)Unit Size 36 by 54 inches, 133 psf Pos, 210 psf Neg.
          2)Unit Size: 42 by 72 inches, 133 psf Pos, 171.4 psf Neg.
          3)Unit Size: 60 by 96 inches, 107 psf Pos, 107 psf Neg.
          4)Unit Size: 72 by 120 inches, 75 psf Pos, 75 psf Neg.
          2.Air Infiltration Resistance: Air leakage no more than 0.02 cfm/sqft of glass area at pressure differential of 6.24 psf (air infiltration tests conducted at pressure differential of 1.57 psf may not be used to justify compliance).
          3.Water Infiltration Resistance: No water penetration at a static air pressure differential of 15 percent of positive design pressure with a maximum tested performance of 20 psf.
          4.Construction: Heavy extruded aluminum-alloy sections, precision cut and assembled with sealed, hairline joints. System is inside glazed.
          5.Member Wall Thicknesses: Window frames, at least 0.090 inch (2.29 mm).
          6.Frame Depth: Windows frames, at least 4.1 inches (104.1 mm).
          7.Sightlines for Flange Window: 2.5 inches (63.5 mm) for jambs, sill and head.
          8.Sightlines for Equal Leg Windows: 2 inches (50.8 mm) for jambs sills and heads.
          9.Corner Construction: Assemble with sealed, hairline joints, made rigid by fastening with No. 12 stainless steel screws.
          10.Glazing Beads: Extruded aluminum concealed glass stops fastened to frame at interior with #10 stainless steel screws with 1 inch (nominal) glass bite.
          11.Finishes: Uniform at all visible surfaces exterior and interior.
          12.Factory Glazing:
          a.Laminated Impact Resistant Glass Units: 7/16 inch (11 mm) thick (nominal) consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Outer and Inner Panes of Laminated Units: 3/16 inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed.
          b)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tints not required.
          2)Tint in Outer Panes: None, clear.
          3)Tint in Outer Panes: Gray.
          4)Tint in Outer Panes: Bronze.
          5)Tint in Outer Panes: Green.
          6)Tint in Outer Panes: Blue.
          7)Tint in Outer Panes: High performance coating, Clear Low-E 366 on No. 2 surface.
          8)Interlayer Type: 0.090 inch / 90 mil (2.2 mm) Sentry Glass Plus.
          ** NOTE TO SPECIFIER ** Delete interlayer opacity not required.
          9)Interlayer Opacity: Standard, clear.
          10)Interlayer Opacity: White, translucent.
          11)Interlayer Opacity: Dark gray (turtle code).
          ** NOTE TO SPECIFIER ** Fill in blank below with tinting option. Tinting on inner panes only available with Clear Low-E 366 or textured coating on outer panes. Delete tints not required.
          12)Tint in Inner Panes: None, clear.
          13)Tint in Inner Panes: __________.
          b.Insulated Laminated Impact Resistant Glass Units: 1.2 inch (31.75 mm) thick (nominal) consisting of a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass, airspace and a sacrificial interior lite.
          1)Interior Sacrificial Lites/Panes:
          ** NOTE TO SPECIFIER ** 1/4 inch thickness required for Dark Gray (Turtle Code). Delete thickness not required.
          a)Thickness: 3/16 Inch (4.8 mm).
          b)Thickness: 1/4 Inch (6.4 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          c)Type: Annealed.
          d)Type: Heat Strengthened.
          ** NOTE TO SPECIFIER ** 1/4 inch thickness required for Dark Gray (Turtle Code). Delete tint not required.
          e)Tint in Outer Panes: None, clear.
          f)Tint in Outer Panes: Gray.
          g)Tint in Outer Panes: Bronze.
          h)Tint in Outer Panes: Green (Solexia).
          i)Tint in Outer Panes: Blue (Azuria).
          j)Tint in Outer Panes: Dark Gray (Turtle Code).
          k)Tint in Outer Panes: High performance coating, Clear Low-E 366 on No. 2 surface.
          2)Interlayer Type: 0.090 inch / 90 mil (2.2 mm) Sentry Glass Plus.
          ** NOTE TO SPECIFIER ** Delete interlayer opacity not required.
          3)Interlayer Opacity: Standard, clear.
          4)Interlayer Opacity: White, translucent.
          5)Airspace: 9/16 inch (14.3 mm) minimum air space.
          6)Interior Sacrificial Lite/Pane: 3/16 inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed.
          b)Type: Tempered.
          7)Tint in Interior Sacrificial Lite: None, clear.
          13.Standards: Miami Dade County NOA (Notices of Acceptance).
          14.Aluminum Alloy and Temper: AA 6063-T5 and T6 temper.
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          C.Casement Windows: "Estate Collection" Series 238 Casement Windows by CGI Windows and Doors, Inc.
          1.Example Sizes and Related Design Pressures: Refer to product approvals for latest results.
          a.Unit Size: 24 by 54 inches, 110 psf Positive, 195 psf Negative.
          b.Unit Size: 37 by 63 inches, 110 psf Positive, 120 psf Negative.
          2.Air Infiltration Resistance: Air leakage no more than 0.04 cfm/sqft of glass area at pressure differential of 6.24 psf (air infiltration tests conducted at pressure differential of 1.57 psf may not be used to justify compliance).
          3.Water Infiltration Resistance: No water penetration at a static air pressure differential of 15 percent of positive design pressure with a maximum tested performance of 16.5 psf.
          4.Construction: Heavy extruded aluminum-alloy sections, precision cut and assembled with sealed, mitered hairline joints and no visible fasteners when vents are closed. Provide grooves in extrusions to receive double weather stripping between vents and frames. Casement and project-out vents outward.
          5.Member Wall Thicknesses:
          a.Frames: At least 0.080 inch (2.03 mm).
          b.Vents: At least 0.090 inch (2.29 mm).
          6.Frame Depth: At least 2.075 inches (53 mm). Provide 0.50 (12.7 mm) inch flanges at perimeter frames.
          7.Sightlines: Jambs, Sill and Head: 3.5 inches (89 mm).
          8.Corner Construction:
          a.At Casement Window Frames and Vents: Assemble with sealed mitered, hairline joints, made rigid by fastening with No. 10 stainless steel screws.
          b.At Frames: 4 stainless steel corner keys and 4 aluminum corner keys.
          c.At Vents: 4 stainless steel corner keys.
          9.Glazing Beads: Extruded aluminum snap-in design, with 0.50 inch (12.7 mm) glass bite for impact-resistant glazing.
          10.Weatherstripping: Dual continuous rows of weatherstripping, one row of Schlegel Q-Lon and another row of Aptus.
          11.Finishes: Uniform at all visible surfaces exterior and interior, vents open or shut.
          12.Factory Glazing:
          ** NOTE TO SPECIFIER ** Delete glazing type not required.
          a.Laminated Impact Resistant Glass Units: 7/16 inch (11 mm) thick (nominal) consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Outer and Inner Panes of Laminated Units: 3/16 inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed.
          b)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          2)Interlayer: 0.090 inch / 90 mil (2.2 mm) Sentry Glass Plus.
          3)Interlayer: 0.075 inch (1.91 mm) Vanceva Storm.
          ** NOTE TO SPECIFIER ** Delete interlayer opacity not required.
          a)Interlayer Opacity: Clear-standard.
          b)Interlayer Opacity: Translucent.
          c)Interlayer Opacity: Dark gray (turtle code).
          4)Overall Thickness: 7/16 inch (11 mm) nominal.
          ** NOTE TO SPECIFIER ** Delete if not required.
          5)Low E and high performance glass coatings as indicated on Drawings.
          ** NOTE TO SPECIFIER ** Delete if not required.
          b.Insulated Laminated Impact Resistant Glass Units: 3/4 inch (19 mm) thick (nominal) insulated Saflex PVB laminated consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior Sacrificial Lites/Panes: 1/8 Inch (3.2 mm) tempered.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          a)Tint in Outer Panes: None, clear.
          b)Tint in Outer Panes: Gray.
          c)Tint in Outer Panes: Bronze.
          d)Tint in Outer Panes: Green (Solexia).
          2)Airspaces: 1/4 inch (6 mm) minimum air space.
          ** NOTE TO SPECIFIER ** Delete if not required.
          3)Low E and high performance glass coatings as indicated on Drawings.
          4)Laminated Units: Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          a)Outer and Inner Panes of Laminated Units: 1/8 inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          b)Type: Annealed glass
          c)Type: Tempered glass.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          d)Tint: None, clear.
          e)Tint: Low E.
          f)Interlayer: 0.090 inch / 90 Mil PVB.
          ** NOTE TO SPECIFIER ** Delete interlayer opacity not required.
          1)Interlayer Opacity: Clear, standard.
          2)Interlayer Opacity: Translucent.
          3)Interlayer Opacity: Dark gray (turtle code).
          13.Window Features:
          ** NOTE TO SPECIFIER ** Additional and upgraded construction. The first two options below are not available with insulated glass. Delete items not required.
          a.Raised Profiles: Extruded double applied raised profile 1 inch (25.4 mm).
          b.Muntins: 3.5 inch (89 mm) muntins.
          c.Screens: At interior of all vents; charcoal fiberglass insect screen fabric, tightly splined into extruded aluminum-alloy frames with rigid corner construction.
          d.Glazing Beads: Ogee glazing bead profile (colonial).
          e.Glazing Beads: Square glazing bead profile (contemporary).
          f.Handles: Folding crank handles.
          14.Standards: Miami Dade County NOA (Notices of Acceptance).
          15.Aluminum Alloy and Temper: AA 6063-T5 and T6 temper.
          ** NOTE TO SPECIFIER ** Delete if all fixed unit or casement and project-out windows not required.
          16.Hardware: Factory applied and field adjusted.
          a.Operators: Single-arm rotary operator with crank handle, running in stainless steel operator track. Provide snubber blocks.
          b.Hinges: Pair of stainless steel 4-bar concealed hinges.
          c.Sash Locks, with Keepers: Two cam locks with lever handle; one at vents less than 30 inch (760 mm) high. Provide one 1/8 inch (3.2 mm) thick stainless steel keeper at each cam lock.
          d.Hardware Colors: Salt-air resistant multi-coat baked enamel in metallic finish.
          ** NOTE TO SPECIFIER ** Delete color not required.
          1)Color: White.
          2)Color: Bronze.
          3)Color: Silver.
          ** NOTE TO SPECIFIER ** Standard construction. Delete if upgrade items selected.
          e.Operator Finish: E-Gard Finish.
          ** NOTE TO SPECIFIER ** Additional and upgraded construction. Delete items not required.
          f.Hardware:
          1)Hardware Finish: CoastGard operator finish.
          2)Stainless steel operator.
          3)Limit opening devices, keyed and non-keyed; in addition to operator.
          4)Washability Hinges: For window sizes 24 inches (610 mm) wide and above.
          5)Locks: Custodial type locks, for institutional use.
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          D.Project-Out / Awning Windows: "Estate Collection" Series 238 Project-Out / Awning Windows by CGI Window and Doors, Inc.
          1.Example Sizes and Related Design Pressures: Refer to product approvals for latest results.
          a.Unit Size: 24 by 54 inches, 110 psf positive, 195 psf Negative.
          b.Unit Size: 37 by 63 inches, 110 psf Positive, 120 psf Negative.
          2.Air Infiltration Resistance: Air leakage no more than 0.04 cfm/sqft of glass area at pressure differential of 6.24 psf (air infiltration tests conducted at pressure differential of 1.57 psf may not be used to justify compliance).
          3.Water Infiltration Resistance: No water penetration at a static air pressure differential of 15 percent of positive design pressure with a maximum tested performance of 16.5 psf.
          4.Construction: Heavy extruded aluminum-alloy sections, precision cut and assembled with hairline joints and no visible fasteners when vents are closed. Provide grooves in extrusions to receive double weather stripping between vents and frames. Swing casement and project-out vents outward.
          5.Member Wall Thicknesses:
          a.Frames: At least 0.080 inch (2.03 mm).
          b.Vents: At least 0.090 inch (2.29 mm).
          6.Frame Depth: At least 2.075 inches (53 mm). Provide 0.50 (12.7 mm) inch flanges at perimeter frames.
          7.Sightlines: Jambs, sill and head - 3.5 inches (89 mm) from tip of flange to glass.
          8.Corner Construction at Casement and Project-Out Window Frames and Vents: Assemble with sealed hairline joints, made rigid by fastening with No. 10 stainless steel screws and the following.
          a.At Frames: 4 stainless steel corner keys and 4 aluminum corner keys.
          b.At Vents: 4 stainless steel corner keys.
          9.Glazing Beads: Extruded aluminum snap-in design, with 0.500 inch (12.7 mm) glass bite for impact-resistant glazing.
          10.Weatherstripping: Dual continuous rows of weatherstripping.
          11.Finishes: Uniform at all visible surfaces exterior and interior, vents open or shut.
          12.Factory Glazing:
          a.Laminated Impact Resistant Glass Units: 7/16 inch (11 mm) thick (nominal) consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Outer and Inner Panes of Laminated Units: 3/16 inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed.
          b)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          2)Interlayer: 0.090 inch / 90 mil (2.2 mm) Sentry Glass Plus.
          3)Interlayer: 0.075 inch (1.91 mm) Vanceva Storm.
          ** NOTE TO SPECIFIER ** Delete interlayer opacity not required.
          a)Interlayer Opacity: None, standard.
          b)Interlayer Opacity: Translucent.
          c)Interlayer Opacity: Dark gray (turtle code).
          4)Overall Thickness: 7/16 inch (11 mm) nominal.
          ** NOTE TO SPECIFIER ** Delete if not required.
          5)Low E and high performance glass coatings as indicated on Drawings.
          b.Insulated Laminated Impact Resistant Glass Units: 3/4 inch (19 mm) thick (nominal) consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior Sacrificial Lites/Panes: 1/8 Inch (3.2 mm) tempered.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          a)Tint in Outer Panes: None, clear.
          b)Tint in Outer Panes: Gray.
          c)Tint in Outer Panes: Bronze.
          d)Tint in Outer Panes: Green (Solexia).
          2)Airspaces: 1/4 inch (6 mm) minimum air space.
          ** NOTE TO SPECIFIER ** Delete if not required.
          3)Low E and high performance glass coatings as indicated on Drawings.
          4)Laminated Units: Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          a)Outer and Inner Panes of Laminated Units: 1/8 inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          b)Type: Annealed glass
          c)Type: Tempered glass.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          d)Tint: None, clear.
          e)Tint: Clear, Low E.
          13.Window Features:
          ** NOTE TO SPECIFIER ** First two options below are not available with insulated glass. Delete features not required.
          a.Raised Profiles: Extruded double raised profile 1 inch (25.4 mm)
          b.Muntins: 3.5 inch (89 mm) muntins.
          c.Screens: At interior of all vents; charcoal fiberglass insect screen fabric, tightly splined into extruded aluminum-alloy frames with rigid corner construction.
          d.Glazing Beads: Ogee glazing bead profile (colonial).
          e.Glazing Beads: Square glazing bead profile (contemporary).
          f.Handles: Folding crank handles.
          14.Standards: Miami Dade County NOA (Notices of Acceptance).
          15.Aluminum Alloy and Temper: AA 6063-T5 and T6 temper.
          16.Hardware: Factory applied and field adjusted.
          a.Operators: Dual-arm rotary operator with crank handle, running in stainless steel operator track. Provide snubber blocks.
          b.Hinges: Pair of stainless steel 4-bar concealed hinges.
          c.Sash Locks, with Keepers: Two cam locks with lever handle. Provide one 1/8 inch (3.2 mm) thick stainless steel keeper at each cam lock.
          d.Hardware Color: Salt-air resistant multi-coat baked enamel in metallic finish.
          ** NOTE TO SPECIFIER ** Delete color not required.
          1)Color: White.
          2)Color: Bronze.
          3)Color: Silver.
          e.Operator Finish: E-Gard Finish.
          f.Hardware:
          ** NOTE TO SPECIFIER ** Delete hardware options not required.
          1)Hardware Finish: CoastGard operator finish.
          2)Stainless Steel operator.
          3)Locks: Custodial type locks, for institutional use.
          4)Short arm operator providing approximately 4 inches (102 mm) of ventilation area.
          5)Long arm operator providing approximately 8 inches (204 mm) of ventilation area.
          6)Manual push out window configuration with pull handle, no screens.
          ** NOTE TO SPECIFIER ** Delete hardware options not required.
          a)Provide limit devices.
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          E.Single Hung Windows: "Estate Collection" Series 360 Aluminum Single Hung Windows by CGI Windows and Doors, Inc.
          1.Example Sizes and Related Design Pressures: Refer to product approvals for latest results:
          a.Large Missile Impact:
          1)Unit Size: 37 by 76 inches, 100 psf Positive, 210 psf Negative.
          2)Unit Size: 54 by 96 inches, 100 psf Positive, 120 psf Negative.
          3)Unit Size: 42 by 120 inches, 100 psf Positive, 120 psf Negative.
          b.Small Missile Impact:
          1)Unit Size: 37 by 76 inches, 100 psf Positive, 200 psf Negative.
          2)Unit Size: 54 by 96 inches, 100 psf Positive, 120 psf Negative.
          3)Unit Size: 42 by 120 inches, 100 psf Positive, 195.9 psf Negative.
          2.Air Infiltration Resistance: Air leakage no more than 0.076 cfm/sqft of glass area at pressure differential of 6.24 psf (air infiltration tests conducted at pressure differential of 1.57 psf may not be used to justify compliance).
          3.Water Infiltration Resistance: No water penetration at a static air pressure differential of 15 percent of positive design pressure with a maximum tested performance of 15 psf (with waterbar adaptor).
          4.Construction: Heavy extruded aluminum-alloy sections, precision cut and assembled with hairline joints and no visible fasteners when sash is closed.
          5.Member Wall Thicknesses:
          a.Frames: .075 - 0.080 inch (2.0 mm).
          b.Sash: .070 - 0.080 inch (2.0 mm).
          6.Frame Depth and Construction: At least 3.625 inches (92 mm). Provide enclosed sloped sill frame member. All sash/vent rails shall be tubular. Sash/vent to engage the jamb 0.50 inches (12.7 mm). Top fixed glass to be installed into a separate fixed sash, rather than to be glazed directly on the frame. Provide 0.50 inch (12.7 mm) flanges at perimeter frames.
          7.Sightlines:
          a.Head: 3.188 inches (81 mm).
          b.Jambs: 3.5625 (90.5 mm).
          c.Meeting Rails: 2.658 inches (67.5 mm).
          d.Sills (Exterior): 4.5 inches (114.3 mm).
          8.Corner Construction: Assemble with sealed hairline joints, made rigid by fasteners with 3 #10 stainless steel screws per corner.
          9.Glazing Beads: Extruded aluminum snap-in design, with 0.50 inch (12.7 mm) glass bite for impact-resistant glazing.
          10.Weatherstripping: Wool pile with center soft fin (gray), minimum two rows at all moving connections.
          11.Finishes: Uniform at all visible surfaces exterior and interior.
          12.Factory Glazing:
          ** NOTE TO SPECIFIER ** Delete glass thickness not required.
          a.Laminated Impact Resistant Glass: 5/16 inch (8 mm) thick (nominal) consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass for Series 360 products.
          b.Laminated Impact Resistant Glass: 7/16 inch (11 mm) thick (nominal) consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass for Series 360 products.
          1)Outer and Inner Panes of Laminated Unit: 1/8 inch (3.2 mm) annealed float glass.
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed glass.
          b)Type: Tempered glass.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          g)Tints in Outer and Inner Panes: Dark Gray (turtle code)
          2)Interlayers:
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          a)Interlayer: 0.075 inch / 75 Mil (1.91 mm) Vanceva Storm composite by Solutia.
          b)Interlayer: 0.090 inch / (2.28 mm) Sentry Glass Plus by Dupont
          ** NOTE TO SPECIFIER ** Delete if not required.
          c)Interlayer Opacity: Translucent interlayer.
          ** NOTE TO SPECIFIER ** Delete if not required.
          3)Low E and high performance glass coatings as indicated on Drawings.
          c.Insulated Laminated Impact Resistant Glass Units: 13/16 inch (21 mm) thick (nominal) insulated laminated unit consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior Sacrificial Lites/Panes: 1/8 Inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed glass
          b)Type: Tempered glass.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          2)Airspaces: 3/8 inch (9.5 mm) minimum air space
          ** NOTE TO SPECIFIER ** Delete if not required.
          3)Low E and high performance glass coatings as indicated on Drawings.
          4)Laminated Units:
          a)Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          b)Outer and inner panes of laminated unit - 1/8 inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          c)Type: Annealed glass
          d)Type: Tempered glass.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          e)Tint: None, clear.
          f)Tint: Low E.
          g)Tint: Dark gray (turtle code).
          13.Hardware: Factory applied and field adjusted.
          a.Balances: Attached to an independent carrier with nylon guides for smooth operation and sash removal feature without disengaging the balance.
          1)Balance Type: Concealed block and tackle balances
          2)Balance Type: Spiral balances.
          b.Covers for balances and jamb installation screws.
          ** NOTE TO SPECIFIER ** Standard construction. Delete if upgrade items selected.
          c.Combination Egress Self Closing Lock and Lift/Pull (Spring Loaded): One at windows 28 inches (71.12 cm) wide and smaller/ two at windows over 28 inches (71.12 cm) wide.
          ** NOTE TO SPECIFIER ** Additional and upgraded construction. Delete items not required.
          14.Window Features:
          a.Meeting Rail Mounted Sweep Lock and Keeper and Lift/Pull: One at windows 28 inches (71.12 cm) wide and smaller/ two at windows over 28 inches (71.12 cm) wide.
          b.Screens: Charcoal fiberglass insect screen fabric, tightly splined into extruded aluminum-alloy frames with rigid corner construction.
          ** NOTE TO SPECIFIER ** Not available with insulated glass. Delete if not required.
          c.Raised Profile Muntins: Extruded double applied raised profile 1 inch (25 mm).
          d.Limit opening device.
          e.Waterbar adaptor.
          f.Glazing Beads: Ogee glazing bead profile (colonial).
          g.Glazing Beads: Square glazing bead profile (contemporary).
          15.Miami Dade County NOA (Notices of Acceptance).
          16.Aluminum Alloy and Temper: AA 6063-T5 and T6 temper; ASTM B 221M.
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          F.Horizontal Rolling Windows: "Estate Collection" Series 375 Aluminum Horizontal Rolling Windows by CGI Windows and Doors, Inc.
          1.Example Sizes and Related Design Pressures: Refer to product approvals for latest results:
          a.Large Missile Impact:
          1)160x60 (2 Eql Panels) or 90x60 (3 Eql Panels) +120psf Pos, -150 psf Neg.
          2)72x76 (2 Eql Panels) or 108x76 (3 Eql Panels) +101.9psf Pos, -101.9 psf Neg.
          b.Small Missile Impact:
          1)60x60 (2 Eql Panels) or 90x60 (3 Eql Panels) +120psf Pos, -209.6 psf Neg.
          2)72x76 (2 Eql Panels) or 108x76 (3 Eql Panels) +120 Pos, -135.5 psf Neg.
          2.Air Infiltration Resistance: Air leakage no more than 0.134 cfm/ft2 of glass area at pressure differential of 6.24 psf (air infiltration tests conducted at pressure differential of 1.57 psf may not be used to justify compliance).
          3.Water Infiltration Resistance: No water penetration at a static air pressure differential of 15 percent of positive design pressure with a maximum tested performance of 18 psf (with waterbar adaptor).
          4.Construction: Heavy extruded aluminum-alloy sections, precision cut and assembled with hairline joints and no visible fasteners when sash is closed.
          5.Member Wall Thicknesses:
          a.Frames: .075 - 0.080 inch (2.0 mm).
          b.Sash: .070 - 0.080 inch (2.0 mm).
          6.Frame Depths and Construction: At least 3.72 inches (94.5 mm). All sash/vent rails shall be tubular. Sash/vent to engage the jamb 0.50 inches (12.7 mm). Fixed panels to be installed into a separate fixed sash, rather than to be glazed directly on the frame. Provide 0.50 inch (12.7 mm) flanges at perimeter frames.
          7.Sightlines For Flange Product With Ogee Beads:
          a.Head: 3.5 inches (81 mm).
          b.Jambs: 3.375 (85.7 mm).
          c.Meeting Rails: 2.625 inches (66.8 mm).
          d.Sills (exterior): 4.125 inches (104.8 mm).
          8.Corner Construction: Assemble with sealed hairline joints, made rigid by fasteners with 3 #10 stainless steel screws per corner.
          ** NOTE TO SPECIFIER ** Delete glazing bead type not required.
          9.Glazing Beads: Extruded aluminum snap-in Ogee design, with minimum 0.50 inch (12.7 mm) glass bite for impact-resistant glazing.
          10.Glazing Beads: Square bead.
          11.Weatherstripping: Wool pile with center soft fin (gray), minimum two rows at all moving connections.
          12.Finishes: Uniform at all visible surfaces exterior and interior.
          13.Factory Glazing:
          a.Laminated Impact Resistant Glass: 5/16 inch (8 mm) thick (nominal) consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass for Series 375 products.
          b.Laminated Impact Resistant Glass: 7/16 inch (11 mm) glass with square glazing beads consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass for Series 375 products.
          1)Outer And Inner Panes Of Laminated Units: 3/16 inch (4.8 mm) annealed float glass
          ** NOTE TO SPECIFIER ** Delete if not required.
          2)Type: Annealed.
          3)Type: Tempered.
          4)Tint in Outer Panes: None, clear.
          5)Tint in Outer Panes: Gray.
          6)Tint in Outer Panes: Bronze.
          7)Tint in Outer Panes: Green (Solexia).
          8)Tints in Outer and Inner Panes: Dark gray (turtle code)
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          9)Interlayer: 0.075 inch (1.91 mm) Vanceva Storm by Solutia.
          10)Interlayer: 0.090 inch (2.28 mm) Sentry Glass Plus by Dupont
          ** NOTE TO SPECIFIER ** Delete if required.
          11)Interlayer Opacity: Translucent interlayer.
          ** NOTE TO SPECIFIER ** Delete if not required.
          12)Low E and high performance glass coatings as indicated on Drawings.
          c.Insulated Laminated Impact Resistant Glass Units: 13/16 inch (21 mm) thick (nominal) consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior Sacrificial Lites/Panes: 3/16 Inch (4.8 mm) annealed.
          a)Tint in Outer Panes: None, clear.
          b)Tint in Outer Panes: Gray.
          c)Tint in Outer Panes: Bronze.
          d)Tint in Outer Panes: Green (Solexia).
          2)Airspaces: 5/16 inch (7.96 mm) minimum air space.
          ** NOTE TO SPECIFIER ** Delete if not required.
          3)Low E and high performance glass coatings as indicated on Drawings.
          4)Laminated Units:
          a)Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          b)Outer and inner panes of laminated unit: 1/8 inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          c)Type: Annealed glass
          d)Type: Tempered glass.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          e)Tint: None, clear.
          f)Tint: Low E.
          g)Tint: Dark gray (turtle code).
          14.Hardware: Factory applied and field adjusted.
          a.Quad roller system consisting of a 1-1/2 inches x 3 inches (38 mm x 76 mm) housing each containing four 3/4 inch (19 mm) diameter nylon wheels with stainless steel raceways on stainless steel axels. Each operable panel to have 2 housings (8 wheels). Wheels to run on PVC track insert.
          b.Self closing heavy duty cast 1-7/8 inch x 4-1/8 inch (47.6 mm x 105 mm) locks (spring loaded): one per operable panel.
          15.Window Features:
          a.Screens: Charcoal fiberglass insect screen fabric, tightly splined into extruded aluminum-alloy frames with rigid corner construction.
          b.Extruded double applied raised profile 1 inch (25 mm) muntins, N/A with insulated glass.
          c.Limit opening device.
          d.Waterbar adaptor.
          e.Ogee glazing bead profile (colonial).
          f.Square glazing bead profile (contemporary).
          g.Unequal size vents
          16.Miami Dade County NOA (Notices of Acceptance).
          17.Aluminum Alloy and Temper: AA 6063-T5 and T6 temper; ASTM B 221M.
          ** NOTE TO SPECIFIER ** With Sentinel by CGI customers benefit from exceptional quality, craftsmanship, energy efficiency and durability at an affordable price. Sentinel's complete line of windows and doors are custom manufactured to enhance the aesthetics of your home while delivering protection from the most extreme coastal weather conditions. Whether considering hurricane impact-resistant windows and doors for a home or business, the Sentinel collection is the best of all worlds - aesthetically appealing, functionally proven and uniquely affordable. Delete if not required.
 
          2.3ALUMINUM WINDOWS (SENTINEL)
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          A.Fixed Windows: "Sentinel"Series 130 Fixed Windows by CGI Windows and Doors, Inc.
          ** NOTE TO SPECIFIER ** Delete if not required.
          1.Fixed Window Types: Rectangular Fixed Windows; for example sizes and related design pressures. Refer to product approvals for latest results.
          a.Unit Size: 37 by 63 inches (Ann/HS Glass) 80 psf Positive, 80 psf Negative.
          b.Unit Size: 49 by 97 inches (HS/HS Glass) 80 psf Positive, 80 psf Negative.
          ** NOTE TO SPECIFIER ** Delete if not required.
          2.Fixed Window Types: Designer Fixed Windows; for example sizes and related design pressures. Refer to product approvals for latest results.
          ** NOTE TO SPECIFIER ** Delete window shapes not required.
          a.Designer Fixed Window Shapes: Half Circle.
          b.Designer Fixed Window Shapes: Arch Top/Eyebrow.
          c.Designer Fixed Window Shapes: Full Circle.
          d.Designer Fixed Window Shapes: Octagon.
          e.Designer Fixed Window Shapes: Hexagon.
          f.Designer Fixed Window Shapes: Chord.
          g.Designer Fixed Window Shapes: Tombstone.
          h.Designer Fixed Window Shapes: Trapezoid.
          i.Designer Fixed Window Shapes: Pentagon.
          j.Designer Fixed Window Shapes: Gothic Pentagon.
          k.Designer Fixed Window Shapes: Standard Colonial.
          l.Designer Fixed Window Shapes: Custom Colonial as indicated on Drawings.
          3.Air Infiltration Resistance: Air leakage no more than 0.08 cfm/sqft of glass area at pressure differential of 6.24 psf (air infiltration tests conducted at pressure differential of 1.57 psf may not be used to justify compliance).
          4.Water Infiltration Resistance: No water penetration at a static air pressure differential of 15 percent of positive design pressure with maximum tested performance of 12 psf.
          5.Construction: Heavy extruded aluminum-alloy sections, precision cut and assembled with sealed, hairline joints.
          6.Member Wall Thicknesses: Rectangular and Designer window fixed frames, at least 0.065 inch (1.65 mm).
          7.Frame Depth: Rectangular and Designer fixed windows frames: At least 2.505 inches (63.63 mm). Provide 0.50 (12.7 mm) inch flanges at perimeter frames.
          ** NOTE TO SPECIFIER ** Delete options below not required.
          a.Provide equal leg adaptor frames.
          b.Provide fin adaptor frames.
          c.Provide flange adaptor frames.
          8.Sightlines for Rectangular and Designer Fixed: Jambs, sill and head - 2 inches (50.80 mm) for flange frames and 1.5 inches (38.10 mm) for equal leg frames.
          9.Corner Construction Rectangular Fixed Window Frames: Assemble with sealed, squared, hairline joints, made rigid by fastening with No. 10 stainless steel screws.
          10.Corner Construction At Designer Fixed Window Frames: Welded corners with sealed hairline joints.
          11.Glazing Beads: Extruded aluminum snap-in design, with 0.75 inch (19 mm) glass bite for impact-resistant glazing at rectangular fixed windows.
          12.Finishes: Uniform at all visible surfaces exterior and interior.
          13.Factory Glazing:
          ** NOTE TO SPECIFIER ** Delete glazing type not required.
          a.Laminated Impact Resistant Glass Units: 7/16 inch (11 mm) thick (nominal) consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Outer and Inner Panes of Laminated Units: 3/16 inch (4.8 mm).
          a)Inner Panes: Heat Strengthened
          ** NOTE TO SPECIFIER ** Delete type not required.
          b)Outer Panes: Annealed
          c)Outer Panes: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          d)Tint in Outer Panes: None, clear.
          e)Tint in Outer Panes: Gray.
          f)Tint in Outer Panes: Bronze.
          g)Tint in Outer Panes: Green (Solexia).
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          2)Interlayer: 0.090 inch / 90 mil (2.2 mm) Saflex PVB Sentry Glass Plus.
          3)Interlayer: 0.075 (1.9 mm) PVB Vanceva Composite.
          a)Interlayer Opacity: Clear-standard.
          b)Interlayer Opacity: Translucent.
          c)Interlayer Opacity: Dark gray (turtle code).
          ** NOTE TO SPECIFIER ** Delete if not required.
          4)Energy Efficient Coatings: Low E and high performance glass coatings as indicated on Drawings.
          ** NOTE TO SPECIFIER ** Delete if not required.
          b.Insulated Laminated Impact Resistant Glass Units: 1 inch (25.4 mm) thick (nominal) consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior sacrificial Lites/Panes: 3/16 Inch (4.8 mm) heat strengthened. Tempered for small missile rating.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          a)Tint in Outer Panes: None, clear.
          b)Tint in Outer Panes: Gray.
          c)Tint in Outer Panes: Bronze.
          d)Tint in Outer Panes: Green (Solexia).
          2)Airspace: 3/8 inch (9.5 mm) minimum air space.
          ** NOTE TO SPECIFIER ** Delete if not required.
          3)Energy advantage, Low E and high performance glass coatings as indicated on Drawings.
          4)Laminated Units:
          a)Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          b)Outer and Inner Panes of Laminated Units: 3/16 inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete if not required.
          c)Type: Annealed.
          d)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          e)Tint: None, clear.
          f)Tint: Clear, Low E.
          ** NOTE TO SPECIFIER ** Additional and upgraded construction. Delete items not required.
          14.Window Features:
          a.Extruded double applied 1 inch (25.4 mm) Low Profile muntins.
          b.Semi-Contoured/Low Profile muntins at rectangular fixed windows.
          c.GBG (Grill Between Glass).
          d.Low Profile with GBG with insulated glass.
          15.Standards: Miami Dade County NOA (Notices of Acceptance).
          16.Aluminum Alloy and Temper: AA 6063-T5 and T6 temper.
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          B.Single Hung Windows: "Sentinel" Series 110 Aluminum Single Hung Windows by CGI Windows and Doors, Inc.
          1.Example Sizes and Related Design Pressures. Refer to product approvals for latest results:
          a.Large and Small Missile Impact:
          1)Unit Size: 53-1/8 by 76 inches (Ann/Ann Glass), 75 psf Positive, 75 psf Negative.
          2)Unit Size: 53-1/8 by 76 inches, (HS/HS Glass) 80 psf Positive, 85 psf Negative.
          2.Air Infiltration Resistance: Air leakage no more than 0.52 cfm/sqft of glass area at pressure differential of 6.24 psf (air infiltration tests conducted at pressure differential of 1.57 psf may not be used to justify compliance).
          3.Water Infiltration Resistance: No water penetration at a static air pressure differential of 15 percent of positive design pressure with maximum tested performance of 12 psf.
          4.Construction: Extruded aluminum-alloy sections, precision cut and assembled with hairline joints.
          5.Member Wall Thicknesses: Frames and Sash, 0.065 inch (1.65 mm).
          6.Frame Depth and Construction: At least 2.505 inches (63.63 mm). Provide enclosed sill frame member. Provide 0.50 inch (12.7 mm) flanges at perimeter frames.
          ** NOTE TO SPECIFIER ** Delete if not required.
          a.Provide equal leg frames.
          7.Sightlines:
          a.Head: 1.75 inches (44.45 mm) with flange frames and 1.25 inches (31.75 mm) with equal leg frames.
          b.Jambs: 2.846 inches (72.29 mm) with flange frames and 2.346 inches (59.59 mm) with equal leg frames.
          c.Meeting rail: 2.819 inches (71.60 mm).
          d.Sill (exterior): 3.875 inches (98.425 mm) with flange frames and 3.375 (85.725 mm) with equal leg frames.
          8.Corner construction: Assemble with sealed hairline joints, made rigid by fasteners with 3 #10 stainless steel screws per corner.
          9.Glazing beads. Extruded aluminum snap-in design, with 0.50 inch (12.7 mm) glass bite for impact-resistant glazing.
          10.Weatherstripping: Wool pile with center soft fin (gray), minimum two rows at all moving connections. Third line of seal at sill with flexible PVB Bulb.
          11.Finishes: Uniform at all visible surfaces exterior and interior.
          12.Factory Glazing:
          ** NOTE TO SPECIFIER ** Delete glass thickness not required.
          a.Laminated impact resistant glass, 5/16 inch (8 mm) thick (nominal) consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Outer and Inner Panes of Laminated Units: 1/8 inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete if not required.
          a)Type: Annealed.
          b)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          g)Tints in outer and inner panes: Dark Gray (turtle code)
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          2)Interlayer: 0.090 inch / 90 mil (2.2 mm) Saflex PVB.
          3)Interlayer: 0.090 inch / 90 mil (2.2 mm) Sentry Glass Plus.
          4)Interlayer: 0.075 PVB Vanceva Composite.
          a)Interlayer Opacity: Clear-standard.
          b)Interlayer Opacity: Translucent.
          c)Interlayer Opacity: Dark gray (turtle code).
          ** NOTE TO SPECIFIER ** Delete if not required.
          5)Energy Efficient Coatings: Low E and high performance glass coatings as indicated on Drawings
          6)Insulated Laminated Impact Resistant Glass Units: 13/16 inch (21 mm) thick (nominal) insulated laminated unit consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          7)Exterior Sacrificial Lites/Panes: 1/8 Inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed.
          b)Type: Heat strengthened.
          c)Type: Tempered.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          d)Tint in Outer Panes: None, clear.
          e)Tint in Outer Panes: Gray.
          f)Tint in Outer Panes: Bronze.
          g)Tint in Outer Panes: Green (Solexia).
          8)Airspaces: 1/4 inch (6.35 mm) minimum air space.
          ** NOTE TO SPECIFIER ** Delete if not required.
          9)Low E and high performance glass coatings as indicated on Drawings.
          10)Laminated Units:
          a)Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          b)Outer and Inner Panes of Laminated Units: 1/8 inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          c)Type: Annealed.
          d)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          e)Tint: None, clear.
          f)Tint: Clear, Low E.
          g)Tint: Dark gray (turtle code).
          13.Hardware: Factory applied and field adjusted.
          ** NOTE TO SPECIFIER ** Delete balances not required.
          a.Balances: Concealed block and tackle.
          b.Balances: Spiral balances.
          c.Head covers for installation screws.
          ** NOTE TO SPECIFIER ** Standard construction. Delete if upgrade items selected.
          d.Combination Egress Self Closing Lock and Lift/Pull: Spring loaded.
          ** NOTE TO SPECIFIER ** Delete quantity not required.
          1)Quantity: One per window, standard.
          2)Quantity: Two per window.
          14.Window Features:
          ** NOTE TO SPECIFIER ** Additional and upgraded construction. Delete items not required.
          a.Screens: Charcoal fiberglass insect screen fabric, tightly splined into extruded aluminum-alloy frames with rigid corner construction.
          b.Extruded double applied 1 inch (25.4 mm) Low Profile muntins.
          c.Extruded double applied Semi-Contoured/Low Profile muntins.
          d.GBG (Grill Between Glass).
          e.Low Profile with GBG with insulated glass.
          f.Limit opening device.
          g.Meeting Rail Mounted Sweep Lock:
          ** NOTE TO SPECIFIER ** Delete quantity not required.
          1)Quantity: One per window, standard.
          2)Quantity: Two per window.
          15.Miami Dade County NOA (Notices of Acceptance): No. 10-0510.11.
          16.Aluminum Alloy and Temper: AA 6063-T5 and T6 temper; ASTM B 221M.
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          C.Horizontal Rolling Windows: "Sentinel" Series 120 Aluminum Horizontal Rolling Windows by CGI Windows and Doors, Inc.
          1.Example Sizes and Related Design Pressures. Refer to product approvals for latest results:
          a.Large and Small Missile Impact:
          1)74 x 63 (2 Eql Panels) or 111x63 (3 Eql Panels) with ANN/ANN Glass: 65psf Pos, 65 psf Neg.
          2)74x63 (2 Eql Panels) or 111x63 (3 Eql Panels) with HS/HS Glass: 80 psf Pos, 90 psf Neg (Fin frame windows limited to 80 psf Pos, 80 psf Neg).
          2.Air Infiltration Resistance: Air leakage no more than 0.7 cfm/ft2 of glass area at pressure differential of 6.24 psf (air infiltration tests conducted at pressure differential of 1.57 psf may not be used to justify compliance).
          3.Water Infiltration Resistance: No water penetration at a static air pressure differential of 15 percent of positive design pressure with maximum tested performance of 12 psf.
          4.Construction: Extruded aluminum-alloy sections, precision cut and assembled with hairline joints.
          5.Member Wall Thicknesses: Frames and sash, 0.065 inch (1.65 mm).
          6.Frame Depth and Construction: At least 2.505 inches (63.63 mm). Provide 0.50 inch (12.7 mm) flanges at perimeter frames.
          ** NOTE TO SPECIFIER ** Delete if not required.
          a.Provide equal leg frames.
          7.Sightlines for Flange Product:
          a.Heads: 2.846 inches (72.29 mm) with flange frames and 2.346 inches (59.59 mm) with equal leg frames.
          b.Jambs:
          1)Moving Panels: 3.436 inches (87.27 mm) with flange frames and 2.936 inches (74.57 mm) with equal legs.
          2)Fixed Panels: 1.750 inches (44.45 mm) with flange frames and 1.250 inches (31.75 mm) with equal leg frames.
          c.Meeting Rails: 2.819 inches (71.60 mm).
          d.Sills (exterior): 4.430 inches (112.52 mm) with flange frames and 3.930 inches (99.82 mm) with equal leg frames.
          8.Corner Construction: Assemble with sealed hairline joints, made rigid by fasteners with 3 #10 stainless steel screws per corner.
          9.Glazing Beads: Extruded aluminum snap-in square bead design with minimum 0.50 inch (12.7 mm) glass bite for impact-resistant glazing.
          10.Weatherstripping: Wool pile with center soft fin (gray), minimum two rows at all moving connections.
          11.Finishes: Uniform at all visible surfaces exterior and interior.
          12.Factory Glazing:
          a.Laminated Impact Resistant Glass: 5/16 inch (8 mm) thick (nominal) consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Outer and Inner Panes of Laminated Units: 1/8 inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed.
          b)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          g)Tints In Outer and Inner Panes: Dark gray (turtle code).
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          2)Interlayer: 0.075 inch (1.91 mm) Vanceva Storm by Solutia.
          3)Interlayer: 0.090 inch (2.28 mm) Saflex PVB Interlayer by Solutia.
          4)Interlayer: 0.090 inch (2.28 mm) Sentry Glass Plus by Dupont.
          ** NOTE TO SPECIFIER ** Delete opacity not required.
          a)Interlayer Opacity: Clear, standard.
          b)Interlayer Opacity: Translucent.
          ** NOTE TO SPECIFIER ** Delete if not required.
          5)Low E and high performance glass coatings as indicated on Drawings.
          b.Insulated Laminated Impact Resistant Glass Unit: 13/16 inch (21 mm) thick (nominal) consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior Sacrificial Lites/Panes: 1/8 Inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed.
          b)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          2)Airspaces: 1/4 inch (6 mm) minimum air space.
          ** NOTE TO SPECIFIER ** Delete if not required.
          3)Low E and high performance glass coatings as indicated on Drawings.
          4)Laminated Units:
          a)Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          b)Outer And Inner Panes Of Laminated Unit: 1/8 inch (3.2 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          c)Type: Annealed.
          d)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          e)Tint: Clear.
          f)Tint: Clear Low E.
          g)Tint: Dark gray (turtle code).
          13.Hardware: Factory applied and field adjusted.
          a.Single roller system consisting of nylon housing each containing one 3/4 inch (19 mm) diameter nylon wheels with stainless steel raceways on stainless steel axels. Each operable panel to have 2 housings (2 wheels). Wheels to run on PVC track insert.
          b.Self Closing Locks: Spring loaded, one per operable panel.
          14.Window Features:
          a.Screens: Charcoal fiberglass insect screen fabric, tightly splined into extruded aluminum-alloy frames with rigid corner construction.
          b.Extruded double applied 1 inch (25.4 mm) Low Profile muntins.
          c.Extruded double applied Semi-Contoured/Low Profile muntins.
          d.GBG (Grill Between Glass).
          e.Low Profile with GBG with insulated glass.
          f.Limit opening devices.
          g.Unequal size vents.
          15.Miami Dade County NOA (Notices of Acceptance) No. 10-0510.12.
          16.Aluminum Alloy and Temper: AA 6063-T5 and T6 temper; ASTM B 221M.
          ** NOTE TO SPECIFIER ** "Estate Collection" Series 450 Door, Sidelites and Transoms by CGI Windows and Doors, Inc. Recognized by architects as a premier line of hurricane impact windows and doors, CGI Estate collection can be found in elegant homes, prestigious resorts, hotels, schools and office buildings. The collection combines best-in-class performance against hurricane force damage with architectural-grade quality, handcrafted details and superior engineering. Delete if not required.
 
          2.4SWING DOORS (ESTATE)
 
          A.Swing Doors: "Sentinel" Series 450 Doors, Sidelites and Transoms by CGI Windows and Doors, Inc.
 
          B.Swing Door Design:
          ** NOTE TO SPECIFIER ** Delete swing not required.
          1.Swing Direction: As indicated on Drawings.
          2.Swing Direction: Out-swing configuration.
          3.Swing Direction: In-swing configuration.
          4.Door Panels: 2 inches (51 mm) thick (nominal) door panels.
          5.Complete frame, threshold and weatherstripping.
          6.Extruded snap-on glazing beads.
          7.Extruded astragal adaptor.
          ** NOTE TO SPECIFIER ** Delete optional items if not required.
          8.Door Features:
          a.True Horizontal Muntin: 4.625 inches (117 mm) wide.
          b.0.50 inch (12.7 mm) nominal thick panel (in lieu of glass where shown or scheduled). Panel can be used to replace part or all of the glass in the door.
          c.Saddle threshold (commercial doors, not rated for water resistance).
          d.Extruded raised profile 1 inch (25 mm) double applied muntins.
          ** NOTE TO SPECIFIER ** Not available with insulating glass. Delete if not required.
          e.Extruded raised profile 3.50 inch (89 mm) double applied muntins.
          f.Ogee profiles.
          g.Configuration: Out-swing configuration.
          h.Configuration: In-swing configuration.
          i.Glazing Beads: Ogee glazing bead profile (colonial).
          j.Glazing Beads: Square glazing bead profile (contemporary).
          9.Size: Refer to Drawings.
          ** NOTE TO SPECIFIER ** Custom door sizes available.
SWING DOOR SIZES
(In inches)
code size door type 6 8 high units 8 high units 9 high units
2068 / 2080 / 2090 single26 9/16 x 80 3/426 9/16 x 96 3/426 9/16 x 108 3/4
2668 / 2680 / 2690 single32 9/16 x 80 3/432 9/16 x 96 3/432 9/16 x 108 3/4
2868 / 2880 / 2890 single34 9/16 x 80 3/434 9/16 x 96 3/434 9/16 x 1083/4
3068 / 3080 / 3090 single38 9/16 x 80 3/438 9/16 x 96 3/438 9/16 x 108 3/4
4068 / 4080 / 4090 pair50 1/2 x 80 3/450 1/2 x 96 3/450 1/2 x 108 3/4
5068 / 5080 / 5090 pair 62 1/2 x 80 3/4 62 1/2 x 96 3/462 1/2 x 108 3/4
5468 / 5480 / 5490 pair66 1/2 x 80 3/4 66 1/2 x 96 3/466 1/2 x 108 3/4
6068 / 6080 / 6090 pair74 1/2 x 80 3/4 74 1/2 x 96 3/474 1/2 x 108 3/4
 
          C.Performance Requirements:
          1.Outswing Door, Transoms and Sidelites: 100 psf Positive and Negative (110 Negative with heat strengthened glass).
          2.Inswing Door (no water infiltration resistance required): 100 psf Positive and Negative (110 Negative with heat strengthened glass).
          3.Inswing Door: 50 psf Positive and 100 psf Negative (110 Negative with heat strengthened glass) where water infiltration resistance is required.
 
          D.Air Infiltration Resistance:
          1.Outswing Door: Transoms and Sidelites: no more than 0.07 cfm/sqft of glass area at static air pressure difference of 6.24 psf.
          2.Inswing Door: Air leakage no more than 0.04 cfm/sqft of glass area, at a static air pressure difference of 1.57 psf.
 
          E.Water Infiltration Resistance:
          1.Outswing Doors, Transoms and Sidelites: Water Infiltration Resistance: No water penetration at a static air pressure differential of 15 percent of positive design pressure with a maximum tested performance of 15 psf.
          2.Inswing Doors: No water penetration at a static air pressure differential of 15 percent of positive design pressure with a maximum tested performance of 7.5 psf.
 
          F.Construction: Heavyweight extruded aluminum sections for wet glazing, precision cut and assembled with sealant filled hairline joints and no visible screws. Provide grooves in extrusions to receive 3 lines of weather stripping where doors abut frames.
          1.Member Wall Thickness: 0.125 inch (3.2 mm) minimum; 0.150 inch (3.8 mm) at hardware mounting locations.
          2.Member Sizes (widths including glazing beads):
          a.Top Rail and Stiles: 1.918 inches (48.7 mm) thick by 5.5 inches (157 mm).
          b.Bottom Rails: 1.918 inches (48.7 mm) thick by 8 inches (203 mm).
          3.Sightlines:
          a.Top Rails: 6.25 inches (15.88 cm).
          b.Jambs: 6.75 inches (17.146 cm).
          c.Sills: 8 inches (20.32 cm).
          4.Door Corner Construction: Assemble using two 3/8 inch (8.9 mm) threaded compression rods in rails, secured at each end with washers and hex nuts.
          5.Glazing Beads: Snap-in design, for interior wet glazing, 0.060 inch (1.5 mm) wall thickness, with at least 0.50 inch (12.7 mm) glass bite for impact-resistant glazing.
          6.Finishes: Uniform at all visible surfaces exterior and interior.
          ** NOTE TO SPECIFIER ** Delete type not required.
          7.Residential Hardware: Including concealed three point locking mechanism with integrated key lock cylinder and thumbturn (single action/one step locking).
          8.Hinges: Hager - Standard weight, three knuckle with concealed anti-friction nylatron bearing, 134 metal leaves with .312 concealed metal pin and plug.
          a.Metal Type: Brass.
          b.Metal Type: Stainless steel.
          9.Commercial Hardware: Including concealed three point locking mechanism with integrated key lock cylinder and thumbturn (single action/one step locking).
          10.Sidelite and Transom Panels:
          a.Product: Series 450 Sidelite, Transom Panels, and Mullions, by CGI.
          b.Design and Performance: Sidelite and transom panels shall interlock with each other and with any CGI approved vertical aluminum tube mullions, at all points of interface, to form a structural unit at each opening. Compliance with impact, wind, water, and structural deflection requirements.
          c.For assemblies with an overall height of less than 108.75 inches utilize self-mating sidelites. For assemblies with an overall height of 108.75 inches or greater, provide structural mullions between sidelites and sidelites, and between sidelites and doors.
          ** NOTE TO SPECIFIER ** Delete transoms not required.
          d.Transoms: Utilize CGI door material transoms with integrated transom/door framing system,
          e.Transoms: Utilize CGI window material transoms with aluminum tube mullion.
          11.Factory Glazing:
          ** NOTE TO SPECIFIER ** Delete glazing type not required.
          a.Laminated Impact Resistant Glass Units: 7/16 inch (11 mm) thick (nominal) Saflex PVB laminated consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Outer and Inner Panes of Laminated Unit: 3/16 inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed.
          b)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          2)Interlayer: 0.090 inch / 90 mil (2.2 mm) film.
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          a)Interlayer Opacity: Clear, standard.
          b)Interlayer Opacity: Translucent.
          c)Interlayer Opacity: Dark gray (turtle code).
          ** NOTE TO SPECIFIER ** Delete if not required.
          3)Low E and high performance glass coatings as indicated on Drawings.
          ** NOTE TO SPECIFIER ** Delete if not required.
          b.Insulated Laminated Impact Resistant Glass Units: 1 inch (25.4 mm) thick (nominal) consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior Sacrificial Lites/Panes:
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)1/8 Inch (3.2 mm) tempered.
          b)1/4 Inch (6 mm) tempered.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          2)Airspaces: 5/16 inch (8 mm) minimum air space.
          3)Laminated Units:
          a)Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          b)Outer and Inner Panes of Laminated Units: 3/16 Inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          1)Type: Annealed.
          2)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint: None, clear.
          d)Tint: Low E.
 
          G.Standards:
          1.Miami Dade County Notices of Acceptance (NOA): 03-0422.02 and 03-0422.03.
          2.Aluminum Alloy and Temper: AA 6063-T5 and T6; ASTM B 221.
          ** NOTE TO SPECIFIER ** "Sentinel" Series 450 SN Door by CGI Windows and Doors, Inc. With Sentinel by CGI customers benefit from exceptional quality, craftsmanship, energy efficiency and durability at an affordable price. Sentinel's complete line of windows and doors are custom manufactured to enhance the aesthetics of your home while delivering protection from the most extreme coastal weather conditions. Whether considering hurricane impact-resistant windows and doors for a home or business, the Sentinel collection is the best of all worlds - aesthetically appealing, functionally proven and uniquely affordable. Delete if not required.
 
          2.5SWING DOORS (SENTINEL)
 
          A.Swing Doors: "Sentinel" Series 450 SN Doors by CGI Windows and Doors, Inc.
 
          B.Swing Door Design:
          ** NOTE TO SPECIFIER ** Delete swing not required.
          1.Out-swing configuration.
          2.2 inches (51 mm) thick (nominal) door panels.
          3.Complete frame, threshold and weatherstripping.
          4.Extruded snap-on square glazing bead profile (contemporary).
          5.Extruded astragal adaptor.
          ** NOTE TO SPECIFIER ** Delete options below if not required.
          6.Muntins: Extruded low profile 1 inch (25 mm) double applied muntins.
          7.Muntins: Semi-contoured (exterior only) 1 inch (25 mm) double applied muntins.
 
          C.Performance Requirements:
          1.Outswing Doors: 3 ft x 8 ft panel.
          ** NOTE TO SPECIFIER ** Delete options below not required.
          a.100 psf Positive and Negative with annealed/annealed glass.
          b.100 psf Positive and 110 psf Negative with heat strengthened glass.
 
          D.Air Infiltration Resistance:
          1.Outswing Doors: No more than 0.07 cfm/sqft of glass area at static air pressure difference of 6.24 psf.
 
          E.Water Infiltration Resistance:
          1.Outswing Doors: No water penetration at a static air pressure differential of 15 percent of positive design pressure with a maximum tested performance of 15 psf.
 
          F.Construction: Heavyweight extruded aluminum sections for wet glazing, precision cut and assembled with sealant filled hairline joints and no visible screws. Provide grooves in extrusions to receive 3 lines of weather stripping where doors abut frames.
          1.Member Wall Thickness: 0.125 inch (3.2 mm) minimum; 0.150 inch (3.8 mm) at hardware mounting locations.
          2.Member Sizes: Widths including glazing beads.
          a.Top Rails and Stiles: 1.918 inches (48.7 mm) thick by 5.5 inches (157 mm).
          b.Bottom Rails: 1.918 inches (48.7 mm) thick by 8 inches (203 mm).
          3.Sightlines:
          a.Top Rails: 6.25 inches (15.88 cm).
          b.Jambs: 6.75 inches (17.146 cm).
          c.Sills: 8 inches (20.32 cm).
          4.Door Corner Construction: Assemble using two 3/8 inch (8.9 mm) threaded compression rods in rails, secured at each end with washers and hex nuts.
          5.Glazing Beads: Snap-in design, for interior wet glazing, 0.060 inch (1.5 mm) wall thickness, with at least 0.50 inch (12.7 mm) glass bite for impact-resistant glazing.
          6.Finishes: Uniform at all visible surfaces exterior and interior.
          ** NOTE TO SPECIFIER ** Delete type not required.
          7.Residential Hardware: Including concealed three point locking mechanism with integrated Copper Creek key lock cylinder and thumb turn (single action/one step locking).
          8.Hinges: Standard 4 inch by 4-1/2 inch (102 mm by 1143 mm) inches aluminum.
          a.Hinge Finish: White finish.
          b.Hinge Finish: Bronze finish.
          9.Door Features:
          ** NOTE TO SPECIFIER ** Delete options below not required.
          a.Levers: Copper Creek-Braxton levers.
          1)Lever Finishes: Brushed Satin.
          2)Lever Finishes: Tuscan Bronze.
          3)Lever Finishes: Polished Brass.
          b.Muntins: Extruded double applied 1 inch (25.4 mm) Low Profile muntins,
          c.Muntins: Extruded double applied Semi-Contoured/Low Profile muntins.
          d.GBG (Grill Between Glass).
          e.Low Profile with GBG with insulated glass.
          10.Factory Glazing:
          ** NOTE TO SPECIFIER ** Delete glazing type not required.
          a.Laminated Impact Resistant Glass Units: 7/16 inch (11 mm) thick (nominal) Saflex PVB laminated consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass
          1)Outer And Inner Panes Of Laminated Unit: 3/16 inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete glazing type not required.
          a)Type: Annealed.
          b)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          g)Interlayer: 0.090 inch / 90 mil (2.2 mm) film.
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          h)Interlayer Opacity: Clear - standard.
          i)Interlayer Opacity: Translucent.
          j)Interlayer Opacity: Dark gray (turtle code).
          ** NOTE TO SPECIFIER ** Delete if not required.
          k)Low E and high performance glass coatings as indicated on Drawings.
          ** NOTE TO SPECIFIER ** Delete if not required.
          b.Insulated Laminated Impact Resistant Glass Units: 1 inch (25.4 mm) thick (nominal) consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior Sacrificial Lites/Panes:
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: 1/8 Inch (3.2 mm) tempered.
          b)Type: 1/4 Inch (6 mm) tempered.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint in Outer Panes: None, clear.
          d)Tint in Outer Panes: Gray.
          e)Tint in Outer Panes: Bronze.
          f)Tint in Outer Panes: Green (Solexia).
          2)Airspaces: 5/16 inch (8 mm) minimum air space.
          c.Laminated Units: Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Outer and Inner Panes of Laminated Units: 3/16 Inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)Type: Annealed.
          b)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete type not required.
          c)Tint: None, clear.
          d)Tint: Clear Low E.
          11.Standards:
          a.Miami Dade County Notices of Acceptance (NOA): 03-0422.02 and 03-0422.03.
          b.Aluminum Alloy and Temper: AA 6063-T5 and T6; ASTM B 221.
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          2.6SLIDING DOORS (ESTATE)
 
          A.Sliding Doors: "Estate Collection" Series 560 Aluminum Sliding Glass Doors by CGI Windows and Doors, Inc.
 
          B.Performance:
          1.Large Missile Rating:
          a.4 by 8 foot panels: 120 psf Positive, 167 psf Negative.
          b.4 by 10 foot panels: 120 psf Positive, 140 psf Negative.
          c.5 by 10 foot panels: 90 psf Positive, 90 psf Negative.
          2.Small Missile Rating:
          a.4 by 8 foot panels: 120 psf Positive, 167 psf Negative.
          b.4 by 10 foot panels: 120 psf Positive, 140 psf Negative.
          c.5 by 10 foot panels: 105 psf Positive, 105 psf Negative.
 
          C.Air Infiltration Resistance: No air leakage more than 0.28 cfm/sqft of glass area at static air pressure difference of 6.24 psf.
 
          D.Water Infiltration Resistance: No water penetration through doors with water bar as follows:
          1.At static air pressure difference of 9 psf w/ 2.50 Inch (63.5 mm) water-bar.
          2.At static air pressure difference of 12 psf w/ 3.062 Inch (77.8) water-bar.
          3.At static air pressure difference of 15 psf w/ 3.688 Inch (93.7 mm) water-bar.
          4.At static air pressure difference of 18 psf w/ 4.25 Inch (108 mm) water-bar.
 
          E.Construction: Heavyweight extruded aluminum sections for wet glazing, precision cut and assembled with sealant filled hairline joints. Provide grooves in extrusions to receive weather stripping where doors abut frames.
          1.Member Wall Thickness: At least 0.080 inch (2.0 mm) to 0.125 inch (3.2 mm) for framing, rails, astragals and interlock members. At least 0.812 inch (20.6 mm) glass bite.
          2.Member Sizes: 2.25 inch (57.2 mm) panels, 2.75 inch (70 mm) deep interlocks; 5.625 inch (14.29 cm) deep frames.
          3.Sightlines:
          a.Head: 6.375 inches (16.19 mm).
          b.Jambs: 6.875 inches (17.46 cm).
          c.Astragals: 11.125 inches (28.26 cm).
          d.Sills: 8.875 inches (22.54 cm).
          4.Door Frame Construction: Door frames must be assembled using a minimum of 3 #12 stainless steel screws per corner.
          5.Door Sill/Track: Must be of tubular single piece construction, designed to drain to exterior through the tubular section, with class I Clear Anodized finish and with beveled adaptor (minimum 0.75 inch (19.05 mm) beveled area) painted to march balance of door.
          6.Glazing Beads: Snap-in design, for interior wet glazing, with at least 0.812 inch (20.64 cm) glass bite for impact-resistant glazing.
          7.Finishes: Uniform at all visible surfaces exterior and interior.
          8.Hardware:
          a.Locking for Operable Panels:
          1)Maximum security stainless steel 0.625 (15.88 mm) inch thick laminated hook bolt lock similar to Adams-Rite MS-1950.
          2)Commercial quality 1.156 inch (29.36 mm) diameter mortised cam thumbturns on interior with solid brass barrel.
          ** NOTE TO SPECIFIER ** Delete option below if not required.
          3)Minimum 5 pin keyed cylinder to match thumbturn specifications on exterior as noted on plans).
          4)3.88 inch (98.55 mm) long by 0.875 (22.22 mm) inch wide cast stainless steel keeper, 0.25 (6 mm) inch thick at lock engagement points and secured with minimum (3) # 10 stainless steel screws secured into minimum 0.125 inch (3.2 mm) thick aluminum at frame jamb.
          b.Door Pulls: Standard back to back tubular 0.75 inch (19 mm) diameter round pulls (10 inches (254 mm) center to center) with 1.50 (38.1 mm) inches by 12 inches (38 mm by 305 mm) escutcheon plate. Provide single sided pulls used at secondary operable panels of XX and OXXO units.
          c.Rollers: Tandem stainless steel rollers with precision bearings in a stainless steel housing (2 rollers per operable door panel). Face adjusted rollers requiring exposed caps to conceal access hole for adjusting screws are not acceptable.
          d.Door stop: Heavy duty metallic round door stop, mounted on head frame member with a single concealed #12 screw, and contain a rubber sleeve to stop door panel. Extruded rubber stops or angle lip stops are not accepted.
          ** NOTE TO SPECIFIER ** Delete hardware finish not required.
          e.Hardware Finishes: Satin Nickel PVD.
          f.Hardware Finishes: Dark Bronze, simulating oil rubbed bronze.
          ** NOTE TO SPECIFIER ** Delete finish not required.
          9.Sightlines:
          a.Heads and Jambs: 5.25 inches (13.34 cm).
          b.Sills: 8.125 inches (20.6 cm).
          c.Interlocks: 5 inches (12.7 cm).
          d.Astragals: OXO and OXXO - 9.25 inches (23.5 cm).
          10.Stainless steel fasteners throughout.
          11.Clear anodized tubular aluminum sill with internal drain chamber. Sill is designed to facilitate the use of tiles on exterior side of door.
          12.Interior sill face trim (waterbar) must be beveled (minimum 0.75 inch (19 mm) beveled area) painted to march door.
          ** NOTE TO SPECIFIER ** Delete type not required.
          a.Water Resistance: 9 psf.
          b.Water Resistance: 12 psf.
          c.Water Resistance: 15 psf.
          d.Water Resistance: 18 psf.
          13.Extruded Snap-on Glazing Beads:
          ** NOTE TO SPECIFIER ** Delete type not required.
          a.Type: Contoured ogee.
          b.Type: Contemporary square profiles.
          ** NOTE TO SPECIFIER ** Delete additional or upgraded items below not required.
          14.Door Features:
          a.Screens: Super duty screens with extruded 1.75 inches (44 mm) vertical members.
          b.Reinforcing: Concealed aluminum reinforcing, steel reinforcing not acceptable.
          c.Impact Resistance: Small missile impact resistant.
          d.Keyed cylinder on exterior face.
          e.Panel framing members must be contained within the plane of the frame. Panel framing members that protrude past the plane of the frame are not acceptable.
          ** NOTE TO SPECIFIER ** Not available with insulated glass. Delete if not required.
          f.Extruded raised profile 1 inch (25 mm) double applied muntins.
          g.Extruded raised profile 3.50 inches (89 mm) double applied muntins.
          15.Factory Glazing:
          ** NOTE TO SPECIFIER ** Delete glazing type not required.
          a.Construction: Laminated impact resistant glass, 7/16 inch (11.12 mm) (nominal) consisting of clear, non-yellowing, non-grazing interlayer sandwiched between two panes of glass for Series 560 products.
          1)Laminated unit make up
          a)One of each on Inner and Outer Panes:
          1)1/4 inch (6 mm) annealed float glass.
          2)1/4 inch (6 mm) tempered float glass.
          3)3/16 inch (4.8 mm) annealed float glass.
          4)3/16 inch (4.8 mm) tempered float glass.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          b)Tint in Outer Panes: None, clear.
          c)Tint in Outer Panes: Gray.
          d)Tint in Outer Panes: Bronze.
          e)Tint in Outer Panes: Green (Solexia).
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          2)Interlayer: 0.090 inch/ 90 Mil Sentryglass Plus by Dupont.
          3)Interlayer: 0.075 inch / 75 Mil Vanceva Storm composite by Solutia.
          ** NOTE TO SPECIFIER ** Delete if not required.
          4)Low E and high performance glass coatings as indicated on Drawings.
          ** NOTE TO SPECIFIER ** Delete if not required.
          b.Insulated laminated impact resistant glass unit - 1 inch (25.4 mm) thick (nominal) consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior sacrificial Lites/Panes:
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)3/16 Inch (4.8 mm) tempered.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          b)Tint in Outer Panes: None, clear.
          c)Tint in Outer Panes: Gray.
          d)Tint in Outer Panes: Bronze.
          e)Tint in Outer Panes: Green (Solexia).
          2)Airspaces: 5/16 inch (8 mm) minimum air space.
          3)Laminated Units:
          a)Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          b)One of each on inner and outer pane.
          ** NOTE TO SPECIFIER ** Delete if not required.
          1)Type: 1/4 inch (6 mm) annealed.
          2)Type: 3/16 inch (4.8 mm) annealed.
          3)Type: 3/16 inch (4.8 mm) heat strengthened.
          4)Type: 3/16 inch (4.8 mm) tempered.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          c)Tint: None, clear.
          d)Tint: Low E.
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          e)Interlayer: 0.090 inch/90 Mil Sentry glass plus.
          f)Interlayer: 0.075 inch/75 Mil Vanceva Storm composite.
          16.Standards: Miami Dade County NOA (Notice of Acceptance): 08-0304.05.
          17.Aluminum Alloy and Temper: AA 6063-T5 and T6; ASTM B 221.
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          2.7SLIDING DOORS (SENTINEL)
 
          A.Sliding Doors: "Sentinel" Series 150 Aluminum Sliding Glass Doors by CGI Windows and Doors, Inc.
 
          B.Performance:
          1.Large Missile Rating:
          a.4 by 8 foot panel (Ann/HS Glass): 60 psf Positive, 60 psf Negative.
          b.4 by 8 foot panels (HS/HS Glass): 80 psf Positive, 80 psf Negative.
 
          C.Air Infiltration Resistance: No air leakage more than 0.19 cfm/sqft of glass area at static air pressure difference of 6.24 psf.
 
          D.Water Infiltration Resistance: No water penetration through doors with water bar as follows:
          1.At static air pressure difference of 9 psf without water-bar adaptor.
          2.At static air pressure difference of 12 psf with water-bar adaptor.
 
          E.Construction: Extruded aluminum sections for wet glazing, precision cut and assembled with sealant filled hairline joints. Provide grooves in extrusions to receive weather stripping where doors abut frames.
          1.Member Wall Thickness: At least 0.070 inch (1.78 mm) to 0.156 inch (3.96 mm) for framing, rails, astragals and interlock members. At least 0.75 inch (19 mm) glass bite.
          2.Member Sizes: 1.34 inch (34 mm) panels, 1.831 inch (46.5 mm) deep interlocks; 7.725 inch (19.6 cm) deep frames.
          3.Sightlines:
          a.Heads: 4.818 inches (12.2 cm).
          b.Jambs: 3.900 inches (9.9 cm).
          c.Astragals: 6.275 inches (15.9 cm).
          d.Sills: 4.870 inches (12.4 cm).
          4.Door Frame Construction: Door frames must be assembled using a minimum of 2 #10 stainless steel screws per corner.
          5.Door Sill/track must be single piece construction, designed to drain through weep on tracks, with class I Clear Anodized finish.
          ** NOTE TO SPECIFIER ** Delete if not required.
          a.Provide water bar adaptor.
          6.Glazing Beads: Snap-in design, for interior wet glazing, with at least 0.750 inch (19 mm) glass bite for impact-resistant glazing.
          7.Finishes: Uniform at all visible surfaces exterior and interior.
          8.Hardware:
          a.Locking for Operable Panels:
          1)Stainless steel single point mortise lock with Zinc cast Powder Coated recessed adaptor.
          2)Zinc cast Powder Coated keeper with one engagement point and secured with (2) #10 stainless steel screws.
          b.Door Pulls: Zinc cast Powder coated handle to match door color. Handles on both exterior and interior. No screws visible on the face of the escutcheon plate.
          ** NOTE TO SPECIFIER ** Delete if not required.
          1)Recessed handle on exterior.
          c.Rollers: Tandem stainless steel rollers with precision bearings in a stainless steel housing (2 rollers per operable door panel). Face adjusted rollers requiring exposed caps to conceal access hole for adjusting screws are not acceptable.
          d.Door stop: Powder coated door stop, mounted on panel top rail member with (2) #10 screws, and contain an extruded rubber sleeve to stop door panel.
          ** NOTE TO SPECIFIER ** Delete finishes not required.
          e.Hardware Finishes: White.
          f.Hardware Finishes: Bronze.
          ** NOTE TO SPECIFIER ** Delete finish not required.
          9.Extruded snap-on glazing beads with contemporary square profiles.
          10.Door Features:
          a.Extruded aluminum screens with finish to match doors.
          b.Concealed aluminum reinforcing (steel reinforcing not acceptable).
          c.Impact Resistance: Small missile impact resistant.
          d.Extruded double applied 1 inch (25.4 mm) Low Profile muntins
          e.Extruded double applied Semi-Contoured/Low Profile muntins.
          f.GBG (Grill Between Glass).
          g.Low Profile with GBG with insulated glass
          11.Factory Glazing:
          ** NOTE TO SPECIFIER ** Delete glazing type not required.
          a.Construction: Laminated impact resistant glass, 7/16 inch (11.12 mm) (nominal) consisting of clear, non-yellowing, non-grazing interlayer sandwiched between two panes of glass.
          1)Laminated Unit Make Up:
          a)Outer And Inner Panes Of Laminated Unit: 3/16 inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          b)Type: Annealed.
          c)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          d)Tint in Outer Panes: None, clear.
          e)Tint in Outer Panes: Gray.
          f)Tint in Outer Panes: Bronze.
          g)Tint in Outer Panes: Green (Solexia).
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          2)Interlayer: 0.090 inch/ 90 Mil Sentryglass Plus by Dupont.
          3)Interlayer: 0.075 inch / 75 Mil Vanceva Storm composite by Solutia.
          ** NOTE TO SPECIFIER ** Delete if not required.
          4)Low E and high performance glass coatings as indicated on Drawings.
          ** NOTE TO SPECIFIER ** Delete if not required.
          b.Insulated laminated impact resistant glass unit - 1 inch (25.4 mm) thick (nominal) consisting of a sacrificial exterior lite and a clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          1)Exterior sacrificial Lites/Panes:
          ** NOTE TO SPECIFIER ** Delete type not required.
          a)3/16 Inch (4.8 mm) tempered.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          b)Tint in Outer Panes: None, clear.
          c)Tint in Outer Panes: Gray.
          d)Tint in Outer Panes: Bronze.
          e)Tint in Outer Panes: Green (Solexia).
          2)Airspaces:
          a)3/8 inch (9.5 mm) minimum air space.
          3)Laminated Units:
          a)Consisting of clear, non-yellowing, non-crazing interlayer sandwiched between two panes of glass.
          b)Outer and Inner Panes of Laminated Units: 3/16 inch (4.8 mm).
          ** NOTE TO SPECIFIER ** Delete type not required.
          c)Type: Annealed.
          d)Type: Heat strengthened.
          ** NOTE TO SPECIFIER ** Delete tint not required.
          e)Tint: None, clear
          f)Tint: Clear Low E.
          ** NOTE TO SPECIFIER ** Delete interlayer not required.
          g)Interlayer: 0.090 inch/90 Mil Sentry glass plus.
          h)Interlayer: 0.075 inch/75 Mil Vanceva Storm composite.
          12.Standards: Miami Dade County NOA (Notice of Acceptance): 08-0304.05.
          13.Aluminum Alloy and Temper: AA 6063-T5 and T6, ASTM B 221.
 
          2.8FINISHES
          ** NOTE TO SPECIFIER ** Delete if not required.
 
          A.AAMA 2603 ESP Finishes: Pretreatment plus 1 coat ESP Siliconized Polyester Coating.
          ** NOTE TO SPECIFIER ** The three standard colors are listed following. Delete colors not required.
          1.Color: White.
          2.Color: Bronze
          3.Color: Driftwood.
          4.Color: As indicated on Drawings.
          5.Color: As selected by Architect.
          ** NOTE TO SPECIFIER ** Delete if not required. Special order, minimum quantities may apply.
 
          B.AAMA 2605 Kynar Finish: Pretreatment plus 2 coat, 70 percent polyvinylidene fluoride (PVDF) coating, or manufacturer approved equal.
          ** NOTE TO SPECIFIER ** Fill in blank below with color designation or delete line as applicable. Delete options for color not required.
          1.Color: _________________.
          2.Color: As indicated on Drawings.
          3.Color: As selected by Architect.
          ** NOTE TO SPECIFIER ** Delete if not required. Special order, minimum quantities apply.
 
          C.Clear Anodized Finishes: NAAMM AA-C2241, 215R1, Class I, minimum 0.7 mills, in natural aluminum color.
          ** NOTE TO SPECIFIER ** Delete if not required. Special order, minimum quantities apply.
 
          D.Wood Grain Finishes: Pretreatment plus base powder coat with textured ink sublimation.
 
          PART 3EXECUTION
 
          3.1PREPARATION
 
          A.Before start of unit installation, check openings for adequacy of pressure preservative treated wood blocking that will receive frames. Check the size, quantity, spacing, clearances, and rigidity of fastenings and their conformance to the specified NOA.
 
          3.2PREPARATION
 
          A.Coordinate with Section 06 10 00 - Rough Carpentry
          1.3/4 inch (19 mm) or 1-1/2 inch (38.1 mm) as per specified NOA rectangular or beveled pressure preservative treated South Yellow Pine blocking, set in a full bed of sealant.
          2.Fasten with to structure with drilled concrete fasteners spaced as required in NOA, so that blocking is continuous and is tightly butted to fill corners of each opening.
 
          B.Coordinate with Section 07 91 26 - Joint Fillers
          1.Sealant at exterior perimeter of aluminum frames, in deeply grooved stucco or in 1/4 inch (6 mm) gaps where other exterior finish materials terminate next to frames.
          2.Sealant in 1/8 inch (3.2 mm) gap at frame interior perimeters where sills and interior finish materials such as gypsum board and tile terminate next to frames.
 
          C.Perform cutting, fitting, forming, drilling, and grinding of frames, without damage to finish, as needed to fit project conditions and make watertight. Replace components with damage to exposed finishes.
 
          3.3WINDOW INSTALLATION
 
          A.Install windows following manufacturer's instructions.
 
          B.Attach window frame and shims to perimeter blocking at openings to accommodate construction tolerances and other irregularities. Maintain integrity of air barriers and vapor retarder sheets.
 
          C.Align windows plumb and level, free of warp or twist.
 
          D.Adjust vents to close snugly and put in smooth operating order.
 
          3.4DOOR INSTALLATION
 
          A.Install doors and frames in accordance with manufacturer's instructions, requirements of NOA for hurricane and impact-resistant construction, and approved shop drawings.
 
          B.Set frames plumb, square, level, and aligned to receive doors. Anchor frames to adjacent construction in strict accordance with manufacturer's recommendations, requirements of governing NOA, and within specified tolerances.
 
          C.Where aluminum surfaces contact alkaline substrates such as concrete or mortar, and metals other than stainless steel or zinc, protect from direct contact by painting reactive substrate and dissimilar metals with a heavy coating of bituminous paint in the field.
 
          D.Hang doors and adjust hardware to achieve specified clearances and proper door operation.
 
          E.Demonstrate doors and hardware are in good working order.
 
          3.5CLEANING
 
          A.Refer to manufacturers instructions for proper cleaning and maintenance of the products.
 
         
END OF SECTION