MasterFormat: 12

Download this Specification for WORD | WP | RTF | TEXT

Find over 500 more construction specifications | Arcat.com

SECTION 11 67 23 - Shooting Range Equipment

FIREARMS TRAINING EQUIPMENT

** NOTE TO SPECIFIER ** Meggitt Training Systems, 1nc.; Firearms training equipment products.
This section is based on the products of Meggitt Training Systems, Inc., which is located at:
296 Brogdon Rd.
Suwanee, GA, 30024
Tel: 800-813-9046
Fax 678-288-1520
Email: mgtts-lesales@meggitt.com
Web: www.meggitttrainingsystems.com
Meggitt Training Systems is the worldwide leader in firearms training equipment and services.
We are specialists in designing and manufacturing stationary and mobile ground target equipment and controls for small arms and armor training required by the armed forces, law enforcement agencies and the security industry worldwide.
Site Planning
Turnkey Design and Installation
Training
Maintenance and Inspection
Logistical Support
We will provide our customers:
The best training systems
Interoperability between legacy and future systems
Long term supportability
Lower life cycle ownership costs
Compatibility with future technology

PART 1

GENERAL

1.1

SECTION INCLUDES

** NOTE TO SPECIFIER ** Delete items below not required for project.

Law Enforcement and Commercial Ranges Equipment:

Bullet Traps.

Clearing Traps.

Shooting Stalls.

Safety Ceilings.

Baffles.

Redirective Guards.

Special Guards.

Ballistic Floor and Wall Treatments.

Target Systems.

10.

Audio/Visual Communication Systems.

11.

Controls.

12.

Mobile Ranges.

1.2

RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

Section 03 15 00 - Concrete Accessories.

Section 04 40 00 - Stone Assemblies.

Section 05 10 00 - Structural Metal Framing.

Section 05 50 00 - Metal Fabrications.

Section 06 10 00 - Rough Carpentry.

Section 09 90 00 - Painting and Coating.

Section 23 00 00 - Heating, Ventilating, and Air Conditioning HVAC.

Section 26 00 00 - Electrical.

1.3

SUBMITTALS

Submit under provisions of Section 01 30 00 - Administrative Requirements.

Product Data: Manufacturer's data sheets on each product to be used, including:

Preparation instructions and recommendations.

Storage and handling requirements and recommendations.

Installation methods.

Shop Drawings:

Submit shop drawings prepared by the manufacturer showing plans, sections, elevations, layouts, profiles and product component locations, including anchorage, bracing, fasteners, accessories and finishes.

Show connection details with screw types and locations, weld lengths and locations, and other fastener requirements.

Manufacturer's Certificates: Certify products meet or exceed specified requirements.

Closeout Submittals: Provide manufacturer's maintenance instructions that include recommendations for periodic checking and adjustment of systems and maintenance of all components.

1.4

QUALITY ASSURANCE

Manufacturer Qualifications: Company specializing in manufacturing products of this Section with ISO Certification certifying manufacturer's quality management system is currently registered to ISO 9001:2000 and ISO 14001; 2004 quality standards.

Manufacturer's Field Representative Qualifications: Experienced in the installation of the specified products.

Installer Qualifications: Installers shall have demonstrated experience in assembly and installation of products similar to those specified in this section.

Coordination of Work: Coordinate layout and installation of indoor shooting range equipment with other construction supported by, or penetrating through, ceilings, including light fixtures, HVAC equipment, fire-suppression system, and partitions

1.5

DELIVERY, STORAGE, AND HANDLING

Deliver materials in manufacturer's unopened, undamaged packaging, with manufacturer's labels intact.

Store products in manufacturer's unopened packaging until ready for installation.

Store materials protected from exposure to rain, snow or other harmful weather conditions, at temperature and humidity conditions.

1.6

PROJECT CONDITIONS

Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

1.7

MAINTENANCE

Bullet trap, safety ceilings, baffles, redirective guards and floor and wall treatments shall require periodic check-ups or inspections to verify the safety of the systems.

PART 2

PRODUCTS

2.1

MANUFACTURERS

Acceptable Manufacturer: Meggitt Training Systems, which is located at: 296 Brogdon Rd. ; Suwanee, GA 30024; Toll Free Tel: 800-813-9046; Fax: 678-288-1520; Email: request info; Web: meggitttrainingsystems.com

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

Substitutions: Not permitted.

Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2

APPLICATIONS/SCOPE

Firearms training equipment shall be provided in the sizes and in the configuration indicated on the Drawings.

Furnish all hardware necessary for the joining of the shooting range equipment specified.

Provide equipment assemblies complete with support structure, stops, and other components required for the required assembly.

Concrete anchors shall be of approved types as specified in Section 03 15 00 - Concrete Accessories.

Field painting of shop primed surfaces shall be as specified in Section 09 90 00 - Painting and Coating.

** NOTE TO SPECIFIER ** There is no essential difference between handgun and rifle ranges. However, the much higher velocities and muzzle energies of most rifle ammunition impose greater demands on the bullet trap, protected zone or stop butt, and danger area of the range. The use of a range for centre fire rifle, in addition to handgun, will often be dependant on the economics of the necessary construction and/or the danger area available. Knowledge of the various shooting activities to be conducted on the range is very important when selecting the proper shooting range components. Contact Meggitt for further information. Select the required components from the following paragraphs and delete those not required.

2.3

LAW ENFORCEMENT AND COMMERCIAL RANGE EQUIPMENT

BULLET TRAPS:

** NOTE TO SPECIFIER ** The following paragraphs contain various types of projectile trap assemblies to shelter the butt ends of the range and for capturing projectiles from rifles, pistols and shotguns. Consult with manufacturer's data sheets for special requirements and limitations of use. Select rubber or metal type for rifle or pistol rated traps as required and delete the paragraphs not required.

Rifle Rated/Rubber Systems: The overall height and depth of the bullet trap shall be as indicated on the Drawings.

Model LE7500 Reclining GranTrap: Trap Assembly for capturing projectiles emitted from rifles, pistols and shotguns along a line substantially parallel to the ground surface, with no backsplatter. Capable of capturing armor piercing, jacketed, semi-jacketed and non-jacketed, shot and slug projectiles with muzzle velocities between 900 and 3,600 feet per second (274 to 1097 meters per second) and energy levels to 3,600 foot-pounds. Fully automatic weapons should not exceed 200 rounds per minute and two hours duration during a 24 hour period. Tracer or incendiary rounds are NOT permitted.

Assembly Height:

Standard Height 9 feet (2.74 M).

Optional Height 8 feet (2.44 M).

Optional Height 12 feet (3.66 M).

Trap Assembly includes a box-type support frame inclined relative to the incoming direction of the projectiles. Particulate material inside the box type Trap Assembly covered by a self-healing membrane is provided to slow down and capture incoming projectiles. Support frame is not to be relied upon to capture projectiles.

Support frame includes an inclined bottom wall, a vertical back wall, and two sidewalls. Walls are fabricated from sheet metal and supported by a steel truss structure arranged and configured to properly support the bottom, back and sidewalls. Support trusses are located 4 to 5 feet (1.2 to 1.5M) along the length/width of the trap assembly.

Support frame includes a recessed target region positioned to capture the majority of the projectiles.

Provide support frame doors, normally closed, positioned proximate to the target region, arranged and configured to allow a portion of the volume particulate material from the target region to be removed from the Trap Assembly through the Support Frame when the door is opened.

Granulate Fill: Fill the space between the self-healing membrane cover and the vertical back wall with GranTex rubber granules. An anti adhesion material may be interspersed between the particles of granular material for increased flow ability. Provide with 2 percent additional fill.

Reserve Portion: Trap Assembly includes a reserve portion of granulate material located above the target region. When the doors described above are opened, the reserve portion of granulate material will flow into the target region to maintain a constant depth of material in the target region.

Supplemental Volume: Trap Assembly includes a supplemental volume of particulate material being arranged and configured to provide a backup for capturing projectiles when the Reserve portion described above has flowed into the target region. Supplemental volume is separated from the Reserve portion by a self-healing barrier. Tracer or incendiary rounds are NOT permitted.

Model LE7500OTR Reclining GranTrap with Overtrap Rubber Covered: Trap Assembly intended for higher volume rifle ranges and capturing projectiles emitted from rifles, pistols and shotguns along a line substantially parallel to the ground surface, with no backsplatter. Capable of capturing jacketed, semi-jacketed and non-jacketed, shot and slug projectiles with muzzle velocities between 900 and 3,600 feet per second (274 to 1097 meters per second) and energy levels to 3,600 foot-pounds. Fully automatic weapons should not exceed 200 rounds per minute and two hours duration during a 24 hour period. Tracer or incendiary rounds are NOT permitted.

Assembly Height:

Standard Height 9 feet (2.74 M).

Optional Height 8 feet (2.44 M).

Optional Height 12 feet (3.66 M).

Trap Assembly includes a box-type support frame inclined relative to the incoming direction of the projectiles. A volume of particulate material inside the box type Trap Assembly covered by a self-healing membrane is provided to slow down and capture incoming projectiles. The support frame is not be relied upon to capture projectiles.

Support frame includes an inclined bottom wall, a vertical back wall, and two sidewalls. Walls are fabricated from sheet metal and supported by a steel truss structure arranged and configured to properly support the bottom, back and sidewalls. Support trusses are located every 4 to 5 feet (1.2 to 1.5M) along the length/width of the trap assembly.

Support frame includes a recessed target region positioned to capture the majority of the projectiles.

Upper frame supports the bullet traps 3/8 inch (9.5 mm) thick AR 500 (BHN) armor plate slop sheet, to protect the top portion of the trap assembly. Armor plate is covered with an air space, created by 7/8 inch rubber strips around the perimeter, and a 1/4 inch (6.5 mm) thick rubber belting, to capture the errant shots not redirect them.

10)

Upper frame is capable of holding up to 5 cubic feet (11.6 cubic meters) of GranTex media. Tracer or incendiary rounds are NOT permitted.

Pistol Rated/Steel:

Model LE2200 Escalator Bullet Trap: Trap designed to recover the major portion of bullet particles from lead collection trays accessible from behind the trap for periodic salvage. Designed for use with all handgun ammunition, all shot shell ammunition including slugs and .22 caliber rim fire rifle ammunition. Suitable for occasional use of soft point rifle and machine gun ammunition with both muzzle velocities and energies no greater than 2,000 feet per second and 2,200 foot pounds respectively. Not designed to accept armor piercing ammunition. Only lead or copper covered lead bullets should be used.

Trap consists three impact plates, per shooting position, arranged with the trailing edge of the lowest plate covering the leading edge of the next highest plate and extended upward at a mean angle not greater than 40 degrees from the horizontal plane to a height of 92 inches (2337 mm). Each impact plate is entirely flat and sandwiched between tie-down bars securing the plates in position. Impacted bullets are directed upward into the deceleration chamber and spent lead projectiles then travel through collection chute to the foot of the trap. Ceiling slope sheets are 1/4 inch (6.5 mm) hot rolled steel and extend the trap to an effective height of 108 inches (2743 mm). Sidewall plates are fabricated from 10 gauge hot rolled steel.

Bullet trap and ceiling slope sheets prefabricated with no field cutting or welding required. Trap is a free standing and mechanically bolted assembly with no external bolts exposed to gunfire. Trap designed to support the ceiling slope sheets overhead. The entire assembly, excluding the small sidewall deflectors, shall be self-supporting. Trap shall not have a gap between the ceiling slope sheet and deceleration scrolls, or anywhere else, where bullet projectiles can escape.

Impact plates fabricated from 5/16 inch AR500 (7.9 mm) thick alloy plate with a (500 BHN hardness). Air foil, lead recovery plates, and deceleration chamber fabricated from 1/4 inch (6.5 mm) ballistiplate alloy plates. Deceleration scrolls fabricated with smooth radius curves and opposing style. Alloy plates, other than impact plates, shall be 1/4 inch (6.5 mm) AR360 (340 to 380 BHN hardness).

All bullet trap components provided with a prime coat of paint at the factory.

No secondary media, such as sand, oil or water, shall be utilized in conjunction with the bullet trap.

Model LE2400 Venetian Blind Bullet Trap: Designed to withstand the impact of all .22 caliber rim fire rifle ammunition, all handgun ammunition up through .44 magnum and all shot shell ammunition including slugs. It is not designed to accept armor piercing ammunition.

Consists of five cantilever supported, 1/4 inch (6.5 mm) AR500 thick alloy impact plates (500 BHN hardness) installed at an angle not greater than 35 degrees from the horizontal plane and designed to direct impacted bullets downward into a deceleration chamber with spent lead particles dropping into a large steel collection tray. Impact plates provided with bolt on, 1/4 inch (6.5 mm) AR500 thick alloy steel leading edge assemblies to catch and contain backsplatter. Leading edges of 1/4 inch (6.5 mm) AR500 thick alloy ground to a cross sectional area. Ceiling slope sheets, bullet trap sidewall plates and wall deflector plates shall be 1/4 inch (6.5 mm) hot rolled steel.

Bullet trap and ceiling slope sheets are prefabricated with no field cutting or welding required. Trap is free standing and ceiling slope sheets shall be supported from the trap

Impact plates fabricated from alloy plate with a AR500 (500 BHN hardness). Alloy plates, other than impact plates, from 1/4 inch (6.5 mm) AR500 alloy plates with a (340 to 380 BHN hardness).

All bullet trap components receive a prime coat of paint at the factory. Tracer or incendiary rounds are NOT permitted.

Rifle Rated/Steel: Overall height and depth of the bullet trap shall be as indicated on the Drawings.

Model LE5000 Escalator Bullet Trap: Designed to stop all bullets fired from the firing line directly into the bullet trap. Designed for constant use with all handgun ammunition including .22, .357, .38, .45, .44 magnum, with all handgun or machine gun ammunition including 9 mm, 10 mm, and .40 caliber, all lead shotgun ammunition including 12 gauge lead slugs, and all soft nose rifle ammunition with muzzle energies under 4,000 foot pounds and velocity not exceeding 4,000 feet per second, including .308, 30 caliber, and .223.

Trap shall shelter the end of the gallery from wall to wall and from floor to the highest bullet path that can be expected from the firing line. Trap shall extend from the floor to a height of 107 inches (2718 mm). Geometry of trap shall be such that any running man, turning targets, or popup targets may be utilized as shown on the Drawings without interference with the trap.

Trap recovers the bullet particles for periodic salvage.

** NOTE TO SPECIFIER ** Select one of the following two paragraphs and delete the one not required. Spent lead sealed pails are standard.

Spent lead sealed pails will collect the spent bullets.

Lead collection conveyor system shall move particles into a sealed shipping container.

** NOTE TO SPECIFIER ** Select the following optional paragraph if required and delete if not required. This option may be used with either the spent lead pail or the lead collection conveyor system specified above.

An airborne particulate cartridge filtration system shall be utilized to draw lead dust from the trap opening through the containment chamber and lead conveyor system into a series of low maintenance cartridge filters. Air shall then pass through a HEPA assembly with inlet plenum to provide 99.97 percent cleaning efficiency on .30-micron particles before discharge.

Construction: Trap is constructed of special heat-treated steel. Frames support the impact plates at a low angle away from the shooter. Lower impact plates and overtrap plates arranged to assure a multiplicity of impacts before the particles enter the chamber for final enervation.

Trap is self-supporting and assembled entirely by mechanical joints with no field cutting or welding required for erection or replacement of components. Sidewall and overtrap plates are attached to facility walls and suspended from ceiling.

Primary impact plates abrasion resistant AR500 alloy steel, with 1/4, 3/8, or 1/2 inch thickness, (500 minimum BHN hardness).

All surfaces of the trap are factory primed on all sides.

Trap is divided into spaces corresponding to shooting points with targets approximately centered on respective impact plates and divisions between impact plates occurring approximately midway between target centers. Tracer or incendiary rounds are NOT permitted.

Services:

** NOTE TO SPECIFIER ** Select the following paragraphs for use with optional conveyor system or trap ventilation system. Delete if not required.

Electrical requirements: Lead collection conveyor motor: 230/460 VAC, 3 phase, 60 Hz; Airborne particulate blower motor: 230/460 VAC, 3 phase, 60 Hz; Airborne particulate pulsing controls: 110 VAC, Single phase, 60 Hz;

Compressed air requirements for airborne particulate pulsing: 90 psi

CLEARING TRAPS:

** NOTE TO SPECIFIER ** Clearing Traps provide a safe and secure location to load and unload a handgun or rifle. It provides protection to structures and personnel by containing any accidental discharge when used properly. Select the trap(s) types required and delete those not required.

Pistol: Model LE1213 Handgun Clearing Trap: Clearing trap designed to provide a safe and secure location to load and unload a firearm. Designed for use with all handgun ammunition including .22, .357, .38, .45, .44 magnum, 9 mm, 10 mm, and .40 calibers with muzzle velocities between 900 and 2,000 feet per second (274 to 610 meters per second) and energy levels to 2,200 foot-pounds. Tracer or incendiary rounds are NOT permitted.

Construction:

Exterior sides of the trap 10 gauge (3 mm) alloy steel. Exterior primed and painted in a Red color for maximum visibility.

Steel safety backer plate is placed on the bottom of the interior chamber and the chamber filled with granular rubber and covered with a rubber panel.

Rubber screen is mounted on the top of the clearing trap to protect against backsplatter. Screen has a slot, into which the weapon is inserted.

Steel safety backer plate on the bottom shall not be used as the primary means to terminate a round fired into the trap. It is used as a "fail-safe" component to prevent damage to structures and injury personnel.

Clearing trap shall be approximately 35 inches (89 cm) high.

Provide with an instruction card mounted to exterior of each trap that is in plain view when a user is clearing a weapon.

Rifle: Model LE1216 Rifle Clearing Trap: Clearing trap designed to provide a safe and secure location to load and unload a firearm. Designed for use with all handgun ammunition including .22, .357, .38, .45, .44 magnum, with all handgun or machine gun ammunition including 9 mm, 10 mm, and .40 caliber, all lead shotgun ammunition including 12 gauge lead slugs, and all soft nose rifle ammunition with muzzle energies under 3,600 foot pounds and velocity not exceeding 3,600 feet per second, including .308, 30 caliber, and .223. Tracer or incendiary rounds are NOT permitted.

Construction:

Exterior sides of the trap 1/4 inch (6.5 mm) AR500 alloy steel except bottom that is 3/8 inch (9.5 mm) AR500 alloy steel. Exterior is primed and painted in a Red color for maximum visibility.

Steel safety backer plate is be placed on the bottom of the interior chamber and the chamber filled with granular rubber and covered with a rubber panel.

Rubber screen is mounted on the top of the clearing trap to protect against backsplatter. Screen shall have a slot, into which the weapon is inserted.

Clearing trap is approximately 35 inches (89 cm) high.

Provide with an instruction card mounted to the exterior of each trap that is in plain view when a user is clearing a weapon.

SHOOTING STALLS

** NOTE TO SPECIFIER ** Shooting stalls organize the firing line into defined shooting positions and provide locations for mounting individual shooter controls. They also provide protection from adjacent shooting positions. Select the stall(s) types required and delete those not required.

Pistol Rated Shooting Stalls:

Model BP10B Bastion Pylon Type Shooting Stall with Barricade: Each stall consists of an internal frame secured to the building to which the panels with shelves and various accessories are mounted. Stalls are suitable for use with service loads of handgun ammunition normally used for gallery range training.

Stalls provide not less than 24 inches (610 mm) of separation between shooters at the shelf height. They define the firing line as located at their edges nearest the shooter at shelf height. Stalls shall provide support for other accessories and hardware as specified.

Pylons: Each stall includes a telescoping tubular steel column to attach to an overhead structure. Frame weldment shall provide a base for attachment to floor. Tubular column serves as a conduit for concealment of the control and communications wiring

Panels molded ABS construction. Interior of panel shall have layered steel sheeting covering all areas that are not reinforced. Panels are removable for servicing of stalls, controls and accessories.

Provide cross members to tie stalls together laterally and provide for mounting drive units of target systems. Lateral members act as raceways for the drive unit and stall wiring.

Stall members shall not deflect more than 1 inch (25 mm) from a static force of 40 pounds (18 Kg) applied any place on the surface and should recover completely after removal of the force.

Each right-hand stall surface shall have an alcove in which a spent brass receptacle is attached.

Provide with removable spent brass receptacle, steel approximately 8 inches (203 mm) wide by 6 inches (152 mm) high, and 3 inches (76 mm) deep. Receptacle recessed into an alcove on the right stall wall to minimize protrusion.

Provide reinforced ABS drop shelf for each stall so that each shooter may use his shelf when needed or drop it out of the way for prone shooting.

Provide shelves with resilient surfaces for weapons; raised lips to prevent accidental drop off; muzzle rest to support handguns with muzzles pointed downrange; and tray area for spent brass.

Mount left end of shelves on hinge pins on the downrange edges of shelves. On the bottom side of shelves, provide slideable locking members that when extended hook on hinge pins of adjacent shooting points.

** NOTE TO SPECIFIER ** Select the one of the following optional paragraphs and delete the one not required.

Wing Barricades not less than 30 inches (762 mm) high and 14 inches (356 mm) wide and hinged at the firing line vertical edges of stalls. Provided with shot-pin type of locks to secure them in their right, left and center positions. Construct of rigid ABS panels finished in black color and suitably reinforced to withstand weight of shooters when leaning against them.

Gate Barricade is a 60 inches high by 11-3/4 inches (2985 mm) wide by 3/4 inches (19 mm) thick, Formica covered wood panel. It is stored on the downrange right hand side of the shooter along with the blast shield. When the shooter wants to use the barricade for strong hand/weak hand shooting, the shelf must be lowered, then the barricade is moved into place by swinging the panel right-to-left (similar to a door) to the center of the shooting position. Center arm has a shot-pin lock that passes through both the arm and the hinge bracket when the barricade is in the use position. Provide blast panels extending downrange from the firing line to prevent the muzzle blast from neighboring shooters from interfering with each other. Each blast panel extends 24 inches (610 mm) downrange and to a height of 72 inches (1829 mm) above the floor. Panels are replaceable and made of acoustical material to absorb shock waves.

Built light terminal for the signal light system into the left stall surface as high and far forward as internal construction permits. Light terminal provided with separate, 1 inch (25 mm) diameter, green, amber and red signal lights.

Model BV10 Phoenix Clear View Shooting Stall with Barricade: Each stall consists of an internal frame that is secured to the building and to which the panels with shelves and various accessories are mounted. Stalls are suitable for use with all standard service loads of handgun ammunition normally used for gallery range training.

Stalls provide not less than 24 inches (610 mm) of separation between shooters at the shelf height. They shall define the firing line as located at their edges nearest the shooter at shelf height. Stalls shall provide support for other accessories and hardware as specified.

Pylons: Each stall includes a tubular steel column to attach to an overhead structure. Frame weldment provides a base for attachment to the floor. Tubular column also serves as a conduit for concealment of the control and communications wiring

Dividers: Each divider is a 1-1/4 inch (32 mm) clear Plexiglas panel integrated into a frame weldment.

Provide cross members to tie the stalls together laterally and for mounting drive units of target systems. Cross members attach to the tubular members within stalls. Lateral members also act as raceways for the drive unit and stall wiring.

Stall members shall not deflect more than 1 inch (25 mm) from a static force of 40 pounds (18 Kg) applied any place upon their surfaces and should recover completely after removal of the force.

Provide reinforced "West Point" type ABS drop shelf for each stall so that each shooter may use his shelf when needed or drop it out of the way for prone shooting.

Provide shelves with resilient surfaces for weapons; raised lips to prevent accidental drop off; muzzle rest to support handguns with muzzles pointed downrange; and tray area for spent brass.

** NOTE TO SPECIFIER ** Select the one of the following optional paragraphs and delete the one not required.

Stall barricades are not less than 30 inches (762 mm) high and 14 inches (356 mm) wide and hinged at the firing line vertical edges of stalls. Provided with shot-pin type of locks to secure them in their right, left and center positions. Construct of rigid ABS panels finished in black color and suitably reinforced to withstand weight of shooters when leaning against them.

** NOTE TO SPECIFIER ** Select the following optional paragraph if required and delete if not required.

Built light terminal for signal light system into the left stall surface as high and far forward as internal construction permits. Light terminal shall provide separate, 1 inch (25 mm) diameter, green, amber and red signal lights.

Rifle Rated Shooting Stalls:

Model BP16B Bastion Pylon Type Shooting Stall with Barricade: Each stall consists of an internal frame that is secured to the building and to which the panels with shelves and various accessories are mounted. Stall is suitable for use with all standard service loads of handgun ammunition and high-velocity rifle ammunition up to and including the M16.

Stalls provide not less than 24 inches (610 mm) of separation between shooters at the shelf height. They shall define the firing line as located at their edges nearest the shooter at shelf height. The stalls shall further provide support for other accessories and hardware as specified.

Pylons: Each stall includes a telescoping tubular steel column to attach to an overhead structure. Frame weldment provides a base for attachment to the floor. Tubular column also serves as a conduit for concealment of the control and communications wiring

Panels molded ABS construction. Interior of panel shall have layered steel sheeting covering all areas that are not reinforced. Panels are removable for servicing of the stalls, controls and accessories.

Provide cross members to tie stalls together laterally and provide for mounting drive units of target systems. Lateral members act as raceways for the drive unit and stall wiring.

Stall members shall not deflect more than 1 inch (25 mm) from a static force of 40 pounds (18 Kg) applied any place on the surface and should recover completely after removal of the force.

Each right-hand member provides a removable, spent brass receptacle.

Provide cross members to tie the stalls together laterally and for mounting drive units of target systems. Cross members attach to the telescoping tubular members within stalls. Lateral members also act as raceways for the drive unit and stall wiring.

Provide reinforced ABS "West Point" drop shelves for each stall so that each shooter may use his shelf when needed or drop it out of the way for prone shooting.

Provide shelves with resilient surfaces for weapons; raised lips to prevent accidental drop off; muzzle rest to support handguns with muzzles pointed downrange; and tray area for spent brass.

Stall blast shield extensions shall extend downrange from shooting separator 24 inches (610 mm) and extend from top of pylon to the floor to function as a full-length blast shield. Stall extension shall consist of removable white acoustical panels slid into a 14-gage, flat black steel frame, which will allow for penetration of a bullet without a ricochet.

** NOTE TO SPECIFIER ** Select the following optional paragraph if required and delete if not required.

Built light terminal for the signal light system into the left stall surface as high and far forward as internal construction permits. Light terminal shall provide separate, 1 inch (25 mm) diameter, green, amber and red signal lights.

Model BV10REB Phoenix Clear View Shooting Stall with Blast Shield and Gate Barrier: Each stall consists of an internal frame that is secured to the building and to which the panels with shelves and various accessories are mounted. Stalls are suitable for use with all standard service loads of handgun and rifle ammunition normally used for gallery range training.

Stalls provide not less than 24 inches (610 mm) of separation between shooters at the shelf height. They shall define the firing line as located at their edges nearest the shooter at shelf height. Stalls shall further provide support for other accessories and hardware as specified.

Pylons: Each stall includes a telescoping tubular steel column to attach to an overhead structure. Frame weldment provides a base for attachment to the floor. Tubular column serves as a conduit for concealment of the control and communications wiring

Dividers: Each divider is a 1-1/4 inch (32 mm) clear panel integrated into a frame weldment.

Provide cross members to tie the stalls together laterally and for mounting drive units of target systems. Cross members attach to the telescoping tubular members within stalls. Lateral members act as raceways for the drive unit and stall wiring.

Stall members shall not deflect more than 1 inch (25 mm) from a static force of 40 pounds (18 Kg) applied any place upon their surfaces and should recover completely after removal of the force.

Provide reinforced "West Point" type ABS drop shelf for each stall so that each shooter may use his shelf when needed or drop it out of the way for prone shooting.

Provide shelves with resilient surfaces for weapons; raised lips to prevent accidental drop off; muzzle rest to support handguns with muzzles pointed downrange; and tray area for spent brass.

Provide blast panels extending downrange from the firing line to prevent the muzzle blast from neighboring shooters from interfering with each other. Each blast panel extends 24 inches (610 mm) downrange and to a height of 72 inches (1829 mm) above the floor. Panels are replaceable and made of acoustical material to absorb shock waves.

** NOTE TO SPECIFIER ** Select the following optional paragraph if required and delete if not required.

SAFETY CEILINGS

** NOTE TO SPECIFIER ** Safety ceiling systems are provided so that misdirected high shots are interrupted before striking any part of the structure, thereby also providing sheltered areas for lighting, ventilation and other equipment as may be required. Select the safety ceiling system type required and delete those not required.

Pistol Rated Safety Ceilings:

Model JG12: System based on the air-space principle that utilizes an air space between a soft frontal surface and a hard back surface so that bullets may enter the front but after ricocheting off the back surface, their particles cannot escape through the entrance holes.

Ceiling system shelter the entire gallery from a height of 8 feet (2.4 m) above the floor from the firing line downrange and shall be based on shooting from the lowest position normally used for a range of the specified type. Sheltered area shall extend from 1 inch (25 mm) of either sidewall.

Air-space ceiling panels pre-fabricated in units of approximately 4 feet square for ease of handling. Dimensions may be altered to suit the requirements of facility. Panels furnished complete with all suspension hardware.

Panels consist of frames constructed of 2 inch (51 mm) by 4-inch (102 mm) lumber faced with unfinished plywood of 5/8 inch (15.9 mm) minimum thickness and covered on the back with hot rolled galvanized steel plate of 10 gauge minimum thickness. Entire assembly rigidly constructed using screws, lag bolts or ring-shank nails spaced on 6 inch (152 mm) maximum center distances.

Panels provided with suitable cleats or eye-bolts for attachment of suspension hardware, and for securing contiguous panels to each other.

Provide with appropriate suspension hardware consisting of No. 2/0 twin loop, zinc plated chain and suitable attachment hardware that provides vertical adjustment.

All wood items are fabricated of (FTW) Fire Treated Wood.

Pistol or Rifle Rated Safety Ceilings:

Ceiling system shelters the entire gallery from a height of 8 feet (2.4 m) above the floor from the firing line downrange and shall be based on shooting from the lowest position normally used for a range of the specified type. Sheltered area shall extend from 1 inch (25 mm) of either sidewall.

Air-space ceiling panels pre-fabricated in units of approximately 4 feet square (.37 sm) for ease of handling. Dimensions may be altered to suit the requirements of the facility. Panels furnished complete with all suspension hardware.

Panels shall consist of frames constructed of 2 inch (51 mm) by 4 inch (102 mm) lumber faced with unfinished plywood of 5/8 inch (15.9 mm) minimum thickness and covered on the back with 10 gauge hot rolled galvanized steel plate of .0125 inch (3.1 mm) AR 225 minimum thickness. Entire assembly shall be rigidly constructed using screws, lag bolts or ring-shank nails spaced on 6 inch (152 mm) maximum center distances.

Panels provided with suitable cleats or eye-bolts for the attachment of suspension hardware, and for securing the contiguous panels to each other.

** NOTE TO SPECIFIER ** Select paragraph for system required and delete items below not required for project.

Pistol Rated (Heavy Duty) ModelJG12B uses steel plate of 3/16 inch (4.8 mm) AR 225 minimum thickness with suspension hardware consisting of 3/16 inch (4.8 mm) welded, zinc plated chain or suitable attachment hardware that provides vertical adjustment.

Rifle Rated Model JG12C use armor steel plate of 1/4 inch (6.3 mm) AR 500 minimum thickness with suspension hardware consisting of No. 2/0 twin loop, zinc plated chain and suitable attachment hardware that provides vertical adjustment.

Heavy Duty Rifle Rated Model JG12D use steel plate of 3/8 inch (9.5 mm) AR 500 minimum thickness with suspension hardware consisting of No. 2/0 twin loop, zinc plated chain and suitable attachment hardware that provides vertical adjustment.

All wood items fabricated of (FTW) Fire Treated Wood.

BAFFLES

** NOTE TO SPECIFIER ** Baffles are provided so that misdirected shots are interrupted before striking any part of the structure and other equipment as may be required. Baffles are used in conjunction with ceiling baffles and bullet traps and consist of a series of downrange baffles located as required. Select the baffle types required and delete those not required.

Pistol or Rifle Rated Baffles

Model JA4: Baffle based on the air-space principle that utilizes an air space between a soft frontal surface and a hard back surface so that bullets may enter the front but after ricocheting off the back surface, their particles cannot escape through the entrance holes.

Sheltered area shall extend from 1 inch (25 mm) of either sidewall.

** NOTE TO SPECIFIER ** Baffles also available in 4 foot by 8 foot (1.2M x 2.4M) panels sizes.

Baffles pre-fabricated in units of approximately 4 feet square (.37 sm) for ease of handling. Dimensions may be altered to suit the requirements of the facility. Panels furnished complete with all suspension hardware.

Panels consist of frames constructed of 2 inch (51 mm) by 4 inch (102 mm) lumber faced with unfinished plywood 5/8 inch (15.9 mm) minimum thickness and covered on the back with hot rolled galvanized steel plate. Entire assembly rigidly constructed using screws, lag bolts or ring-shank nails spaced on 6 inch (152 mm) maximum center distances.

Provide panels with suitable cleats or eye-bolts for attachment of suspension hardware, and for securing the contiguous panels to each other.

** NOTE TO SPECIFIER ** Select from the following four paragraphs for system required and delete items below not required for project.

Pistol Rated Model JA4: Provided with galvanized steel plate of 10 gauge (31 mm) minimum thickness with appropriate suspension hardware consisting of No. 2/0 twin loop, zinc plated chain and suitable attachment hardware that provides vertical adjustment..

Heavy Duty Handguns Model JA4B: Provided with steel plate of 3/16 inch (4.8 mm) AR 225 minimum thickness.

Rifles Model JA4C: Provided with armor steel plate of 1/4 inch (6.3 mm) AR 500 minimum thickness.

Heavy Duty Rifle Model JA4D: Provided with armor steel plate of 3/8 inch (9.5 mm) AR 500 minimum thickness.

All wood items fabricated of (FTW) Fire Treated Wood.

Provide with appropriate suspension hardware consisting of 3/16 inch (4.8 mm) welded, zinc plated chain or suitable attachment hardware that provides vertical adjustment.

Model JA8 (Heavy Duty): Airspace Baffle provided to secure the top of granular bullet type traps from misdirected shots. Baffle shelters the top of the trap and is designed so that bullets striking the baffle, are trapped between the front surface and the steel back surface. All parts are able to withstand direct hits from all mid-range target ammunition and regular service ammunition, including magnum, from handguns, and shotguns. Armor piercing ammunition shall not be used.

Baffles extend to within 1 inch (25 mm) of the range sidewalls, or into an area sheltered by other ballistic protection.

Provide baffle with provision for appropriate mounting including attachments to overhead structures. All mounting hardware shall be provided.

** NOTE TO SPECIFIER ** Select from the following two paragraphs for system required and delete items below not required for project.

Pistol Rated Model JA8B: Back surface of the baffle shall have a minimum thickness of 3/16 inch (4.76 mm) and shall be manufactured from heat treated AR225 armor plate. Front surface of the baffle shall have a minimum thickness of 1/4 inch (6.5 mm) and shall be manufactured from conveyor belting. Front surface shall be held off the back surface by using one layer of 7/8 inch (22.22 mm) thick belting on all four sides. Spent rounds shall be contained in the airspace.

Rifle Rated Model JA8C: Back surface of the baffle shall have a minimum thickness of 1/4 inch (6.35 mm) and shall be manufactured from heat treated AR500 armor plate. Front surface of baffle shall have a minimum thickness of 1/4 inch (6.35 mm) and shall be manufactured from conveyor belting. Front surface shall be held off the back surface by using one layer of 7/8 inch (22.22 mm) thick belting on all four sides. Spent rounds shall be contained in the airspace.

Provide with appropriate suspension hardware consisting of 3/16 inch welded, zinc plated chain or suitable attachment hardware that provides vertical adjustment.

REDIRECTIVE GUARDS

** NOTE TO SPECIFIER ** Redirective guards provide protection from adjacent shooting positions. Select the guard(s) required and delete those not required.

Pistol and Rifle Rated Redirective Guards:

Model JR5B: Redirective cove shelters the area behind it and is designed so that bullets hitting the cove are redirected down-range toward the bullet trap so nothing can be directed at the shooters. All parts shall be able to withstand, without damage, direct hits from all mid-range target ammunition and regular service ammunition from handguns and shotguns, except armor piercing.

Cove shall extend to within 1 inch (25 mm) of the building structure at both ends or into the area sheltered by other members.

Provide cove with provisions for appropriate mounting. For overhead suspension from structure use 2/0 twin loop, zinc-plated chain with "S" hooks and turnbuckles provided by the manufacturer.

All parts of the system shall be of materials and construction suitable for the class of service designated. Material shall be a minimum of 3/16 inch (4.8 mm) AR 225 armor plate steel.

** NOTE TO SPECIFIER ** Select from the following three paragraphs for system required and delete items below not required for project.

Standard Heavy Duty Handgun Model JR5B: Material shall be a minimum of 3/16 inch (4.8 mm) AR 225 armor plate steel. Provide with appropriate suspension hardware consisting of No. 2/0 twin loop, zinc plated chain and suitable attachment hardware that provides vertical adjustment.

Rifle Rated Model JR5C: Material shall be a minimum of 1/4 inch (6.5 mm) AR500 armor plate. Provide with appropriate suspension hardware consisting of 3/16 inch welded, zinc plated chain or suitable attachment hardware that provides vertical adjustment.

Heavy Duty Rifle Rated Model JR5D: Material shall be a minimum of 3/8 inch (6.59.5 mm) AR500 armor plate. Provide with appropriate suspension hardware consisting of 3/16 inch welded, zinc plated chain or suitable attachment hardware that provides vertical adjustment.

SPECIALTY GUARDS

** NOTE TO SPECIFIER ** Specialty guards provide protection from adjacent shooting positions. Select the guard(s) required and delete those not required.

Pistol Rated Specialty Guards

Model JR7: Redirective guard secures the range from misdirected shots and redirect bullets hitting the guard away from shooters. All parts of the guard shall be able to withstand, without damage, direct hits from all regular service ammunition from handguns and shotguns and magnum ammunition, except armor piercing.

Provide guard with provisions for appropriate mounting by anchor bolts or other devices.

All parts of the guard shall be of materials and construction suitable for the class of service designated.

** NOTE TO SPECIFIER ** Select one of the following two paragraphs for system required and delete items below not required for project.

Rifle Rated Model JR7C. Material shall be a minimum of 1/4 inch (6.3 mm) AR500 steel factory welded and painted with a primed coat.

Heavy Duty Rifle Rated Model JR7D: Material shall be a minimum of 3/8 inch (9.5mm) AR500 steel.

Model JR3: Redirective wall guard for small area protective use. Guard shelters the area behind it and designed to redirect bullets hitting the guard away from shooters. All parts of the guard shall be able to withstand, without damage, direct hits from all regular service ammunition from handguns and shotguns and magnum ammunition, except armor piercing.

Provide guard with provisions for appropriate mounting by anchor bolts or other devices.

Guard shall be of materials and construction suitable for the class of service designated.

** NOTE TO SPECIFIER ** Select from the following two paragraphs for system required and delete items below not required for project.

Rifle Rated Model JR3C: Material shall be a minimum of 1/4 inch (6.3 mm) AR500 steel factory welded and painted with a primed coat.

Heavy Duty Rifle Rated Model JR3D: Material shall be a minimum of 3/8 inch (9.5mm) AR500 steel.

BALLISTIC FLOOR AND WALL TREATMENTS

** NOTE TO SPECIFIER ** Ballistic wall and floor treatments provide protection for stray or misplaced shots. Acoustical foam reduces the reflected noise levels. Select the treatment(s) types required and delete those not required.

Ballistic Floor and Wall Treatments:

Pistol and Shotgun Rated Model BWA: Combat Wall System designed for use with all handgun and shotgun ammunition up to and including 40 caliber/12 ga. 00 buckshot.

System consists of 10 gauge steel plate mounted to walls with 3/4 inch thick by 2 inch (51 mm) rubber stripe mounted to steel plate to create an air space for the bullets to be contained in. The outer surface has a 1/4 inch (6.5 mm) conveyor belt rubber layer mounted to the rubber strips for a soft penetrable surface to contain the bullets inside the air space.

System is modular to facilitate ease of installation in the field and can be preassembled or assembled in the field at the site.

All wood items fabricated of (FTW) Fire Treated Wood.

Pistol and Shotgun Rated Model BWB Ballistic Combat Wall System (Heavy Duty): Combat Wall System designed for use with all handgun and shotgun ammunition up to and including 40 caliber/12 gauge 00 buckshot.

System consists of 3/16 inch thick AR225 steel plate mounted to the walls with 3/4 inch (19 mm) thick by 2 inch (52 mm) rubber strips mounted to the steel plate to create an air space for the bullets to be contained. The outer surface has a 1/4 inch (6.5 mm) conveyor belt rubber layer mounted to rubber strips for a soft penetrable surface to contain the bullets inside the air space.

System is modular in design to facilitate ease of installation in the field and can be preassembled or assembled in the field at the site.

All wood items fabricated of (FTW) Fire Treated Wood.

Rifle Rated Model BWC Ballistic Wall System: Combat Wall System designed for use with all handgun, shotgun and rifle ammunition up to and including .223 rifle ammunition.

System consists of rubber panels and rubber/wood constructed with air spaces to allow penetration through the self-healing outer rubber surface. Standard wall becomes the backing for the occasional shots fired. Projectile is captured within the air space and all chance of ricochet will be eliminated.

System is modular to ease installation and includes all rubber/wooden framing, rubber panels, and assembly fasteners. Panel firmly secured to the rubber/wooden frame at both top and bottom of the wall.

Front side of the wall baffle shall have 1/4 inch (6.5 mm) rubber belting.

Back surface of baffle shall have a minimum thickness of 1/4 inch (6.5 mm) manufactured from heat treated AR500 armor plate.

All wood items fabricated of (FTW) Fire Treated Wood.

Rifle Rated Model BWD Ballistic Wall System (Heavy Duty): Hanging Wall System designed for use with all handgun, shotgun and rifle ammunition up to and including the .223 rifle ammunition.

System is modular to installation and includes all rubber/wooden framing, rubber panels, and assembly fasteners. Panel shall be firmly secured to the rubber/wooden frame at both top and bottom of the wall.

Front side of the wall baffle shall have 1/4 inch (6.5 mm) rubber belting.

Back surface of the baffle shall have a minimum thickness of 3/8 inch (9.5 mm) manufactured from heat treated AR500 armor plate.

All wood items fabricated of (FTW) Fire Treated Wood.

Absorption Acoustical Foam:

Model No. AAF-Class1: 2 inch (51 mm) acoustical sculptured melamine foam is mounted on the safety ceiling and baffles, from the firing line downrange toward the bullet trap.

Attach foam to bare walls or wood panels with structural adhesive provided with acoustical foam.

If indicated on the Drawings, mount additional materials to the walls behind the firing line for additional acoustical absorption.

Absorption acoustical foam sculptured surface contour is based on the anechoic wedge principle and presents a surface area 300 percent greater than a flat surface. Melamine foam provides superior noise reduction characteristics, resists crushing from physical contact, and is rated for ASTM E-84 Class 1 flammability.

Shredded Rubber Plank:

Model SRP: Manufactured of high strength, coarse shredded SBR rubber stock, bound with a highly elastic polyurethane binder and molded under high compression and heat until fully cured. Polyurethane binders shall be of MDI type and contain no heavy metals. SBR rubber stock shall be free of metal, fiber and other similar deleterious substances.

Thickness:

** NOTE TO SPECIFIER ** Select one of the following thickness paragraphs and delete those not required.

1.0 inches (25 mm).

1.5 inches (37 mm).

1.7 inches (43 mm).

2.0 inches (51 mm).

Physical Properties:

Density: Minimum 50 pcf.

Tensile Strength: Greater than 160 psi.

Elongation: Greater than 160 percent.

Flash Point: Greater than 650 degrees F.

Accelerated Aging: 2500 hours, Weatherometer - no change

Freeze/Thaw: Minus 58 degrees F, 40 Cycles - no change

Electrical Conductivity (Siemans): 1.1 x 10-4 or better.

Compression Endurance: 10,000 cycles/10 ton - no deterioration

Flammability: When tested in accordance with ASTM D-2859, the material shall be rated "pass."

TARGET SYSTEMS

** NOTE TO SPECIFIER ** Target systems are provided at shooting stalls and provide individual shooter with various levels of target controls. Select the target system(s) required and delete those not required.

Model XWT 360 degree Target Oscillation: Monorail Type system allows the target to be turned from a center concealed position through a 90 degrees arc for a total of 360 degrees, to expose either the right or left face in less than 0.5 seconds in either direction. Equipment intended for full-time activities with mid-range handgun/rifle ammunition. Any portion 60 inches downrange of the firing line must be able to withstand occasional impact from misdirected bullets from proper courses of fire. Rail, front exposed surfaces of the carrier, rail hangers and the stops, are able to withstand occasional direct impacts of ammunition that may be fired in the range specified.

Supports all bulls-eye and silhouette targets up to and including the B21 and B27 silhouette targets with the use of target backers.

Provides automatic redundant stops at the firing line and single automatic stop at the butts end.

Targets travel speed is variable up to of 8 feet per second and stop close enough to the designated target lines so that the differences are not perceptible to the shooters at the firing line. (plus or minus 3/8 of an inch)

Target holders for offhand targets support the targets so that top edges are approximately 70 inches (1778 mm) from the floor.

Design Requirements: Design to assure long service life with minimal service when operated full-time for the class of service specified.

Monorail assembly consists of square sections with a horizontal distance across the open end of rail shall not be less than 2 inches (52 mm). Minimum weight of rail shall not be less than 3.5 pounds per lineal foot. Rail sections and hangers are assembled by bolted connections. Provide with suspension hangers and anti-sway restraints to minimize longitudinal and lateral movement of rail.

Design eliminates the obstructions caused by drive units, motors, control boxes and allows for enhanced airflow at the firing line.

Target carrying cars, steel construction with a steel, slanted prow facing the shooters. Carriers provided with steel dust guards.

Carriers ride on (4) upper and (4) lower resilient wheels and contain all the mechanisms for the target transport. Two of the lower wheels shall be driven by a DC electric motor located inside the carrier body.

Target carriers have identifying numerals, a minimum of 4 inches (102 mm) high, on the front of the cars.

Primary frontal section of target carrier body shall be made from 1/4 inch (6.35 mm) AR500 armor plate.

Vertical section that protects the rotating shaft must also be made from 1/4 inch (6.35 mm) AR500 armor plate.

On-board battery powers the carrier assembly. Carrier shall automatically be charged whenever the carrier is in the Home (firing Line) position by a separate charging system.

There shall be no cables, conduit or other means of electrical power and control going down range that can be hit by errant shots or be shorted out by spent brass landing on the track.

10)

Target carrier shall have an on-board microprocessor to control the carrier operations that will wirelessly communicate to the Local Control Unit (LCU) via a WiFi system.

11)

A long life lithium battery is supplied with the system. Whenever the carrier is in the home position, the battery will receive a charge.

Operations: For linear positional accuracy, the carrier has sensors that will measure relative position and speed of the carrier, as well as a home sensor. Sensors communicate with the on-board processor.

A DC gear motor is located on the carrier assembly to provide 360 degree target presentations.

Output shaft of the motor shall be mechanically connected to the target holder with a resilient coupling.

Assembly provided with eclectic sensors that provide precise position information to the on-board processor.

Provide with 5.5 inch wide target holder deflectors manufactured from 1/4 inch (9.4 mm) AR500 armor plate. Clamping system shall have adjustable tension jaws and depth adjustable teeth that perforates and grips the target backer.

Target carrier shall house a protected target illumination light fixture that provide a minimum of 12 lumens of illumination and shall be adjustable up to (10) levels of brightness.

Track is assembled from 12 gage galvanized steel sections with a "T" top for the attachment of overhead support grippers. Track sections are mechanically joined and the support grippers shall provide one inch vertical adjustment. Track sections shall be designed to shed spent brass or other debris.

In addition to the target light, there is a feature that allows the light to be used in a muzzle flash mode when programed to do this.

No cables or wires shall extend beyond the firing line. Track shall not be electrified for target movement or operations of any kind.

Operational parameters for the use of this system are: 0 plus or minus 40 degree C and storage environment of minus 40 to plus 70 degree C. System is designed for non-condensing humidity for indoor applications.

10)

No overhead obstructions like motors, control boxes or other obstructions are allowed to enhance the airflow at the range at the firing line.

11)

Power for the unit is provided for at the firing line for the shooting stall crossmember system.

12)

Control and logic functions are low-voltage powered (27 VDC maximum). Control and logic signals have a minimum of a 5-volt threshold for noise immunity. Wiring within electronics chassis by printed circuit boards wherever applicable. All connections to chassis shall be by barrier strips.

13)

Target Oscillation: System permits targets to be turned from a center concealed position to expose either the right or left side in either direction or continues in one direction for 360 degrees. Each target may be edged or exposed on either side at anytime while it is at its distance stops, while traveling to or from the firing line, and independent of all other targets.

14)

Oscillation pod has a descender that carries the bottom bearing of the target spindle to which the target holder is attached. All surfaces subjected to direct hits are angled so that the major bullet particles are deflected downrange.

Model CBN Monorail Target System: Consists of monorail track, suspension system supports, upper target carrier body, lower carrier target holder assembly, drive unit drive cable, take-up assembly, and electronic control module. System has capability of stopping at 1 foot, yard or meter increments down range with allowable coast.

Upper target carrier body is a welded steel fabrication with 4 upper and 2 lower adjustable rubber wheels. Front face of target carrier is positioned no more than 30 degrees to deflect misdirected shots down range toward the bullet trap. Main target control components are housed in a separate drive unit and not in the target carrier. Upper target carrier body has provisions for attachment of galvanized steel drive cable and lower carrier target holder/turner weldment. Unit is factory painted brown.

Drive unit consists of a steel frame, drive train and motor. Assembly is bolted to the booth supported insta-wire or cross tube. Steel frame is a welded, rigid, electro-galvanized steel fabrication. Motor is a fractional HP motor size selected for the intended use.

Solid state electronic drive control module is provided with receptacles for connection to AC power source, drive motor, individual control, master control, and 2 plug-in relay microprocessor controlled printed circuit board. Controller has capability to send the target carrier to any position on the track in one foot increments plus or minus 1 percent with allowable coast. Control circuitry is housed in the painted drive unit assembly with easy access by the removal of two thumb screws on each side of the assembly.

To provide 180 degree target presentations, a 24 volt DC gear motor is mounted on the lower carrier interchangeable target holder assembly. Assembly is fabricated from steel and shall be attached to upper carrier by 4 bolts. Output shaft of motor is mechanically connected to target holder with a resilient coupling. Provide assembly with electrical and mechanical limits to achieve precise 180 degree EDGE/FACE-L, FACE-L/FACE-R and EDGE/FACE-R movements. The 5-1/2 inch (12.5 mm) wide target holder deflectors are fabricated from alloy steel and have adjustable tension jaws that perforate and grip the target and backer. Replaceable alloy target holder deflectors deflect all misdirected shots toward the bullet trap.

Monorail track is fabricated of 12 gauge formed electro-galvanized interlocking sections with a channel top for the attachment of overhead support grippers. Track sections are mechanically joined and the support grippers provide 1 inch (25 mm) of vertical adjustment. Track assembly shall not utilize bus wire type technology with carbon pick up brush. Terminal end of track is fitted with take-up assembly containing 2 guide pulleys and 1 adjustable take-up pulley.

Model CEE, CasRail Econoline Monorail Target Retrieval System: Target retrieval systems are an electrically operated, monorail types. Equipment is intended for full-time activities with mid-range handgun ammunition. Equipment shall withstand occasional impacts from misdirected bullets from proper courses of fire when the carrier cars are at target lines. Front exposed surfaces of the carrier, rail hangers and stops shall be able to withstand occasional direct impacts of all ammunition that may be fired by most handguns.

Functional Requirements: System shall support transport all bull's eye and silhouette targets up to and including the B29 and B30 silhouette targets with cardboard backers.

Design Requirements: Systems designed to assure long service life with minimum service when operated full-time for the class of service specified.

Provide with offhand target holder that will suspend targets for handgun shooting so that the top edge is approximately 70 inches (1778 mm) above the floor and securely hold the targets and quickly release them when desired for changing.

Monorail is modular with pieces that slide together for installation. Monorail shape is made to provide a place where drive cable can be protected during operation. There is also a flat track on each side of the vertical section used for target carriers to ride back and forth.

Target carrier car consists of a steel chassis with 4 rubber wheels that ride on the monorail. Carrier fabricated with a vertical recess into which target spindles are attached.

Terminal stop consists of a bracket for attachment and provides a means for attaching the monorail and a mating member of the carrier-car stabilizing member and turnaround ball-bearing pulleys for the cable.

Drive unit houses motor power, rated at 117 VAC that moves target carrier back and forth. Local control switch is mounted on shooting stall divider and activates the motor to go downrange or back to the firing line. At any place in between the ends of the monorail track, the target carrier can be stopped by letting go of the momentary switch, which stops the target carrier in either direction. Motor is a 1/3 hp unit and requires a separate 20 AMP circuit for every two drive units.

Provide wide target holders for full-size police silhouette targets. They shall consist of two target-holding clips located 18 inches (457 mm) apart and connect to a common descender.

Model CEB, Electric Target Retrieval System: Systems shall be electrically operated trolley-wire type. Equipment is intended for full-time activities with midrange handgun ammunition. Equipment is able to withstand occasional impacts from misdirected bullets from proper courses of fire when the carrier cars are at the target lines. Front exposed surfaces of carrier, rail hangers and stops shall be able to withstand occasional direct impacts of all ammunition that may be fired in type range specified.

Functional Requirements: System provides control of the target transport by means of trolley wire with internal connections for remote 115 vac control switch is mounted in the shooting stall.

Provide an offhand target holder for each system that will suspend all bull's-eye targets for gallery courses so that their top edge will be approximately 70 inches (1778 mm) above the floor. It shall securely hold the targets and quickly release them when desired for changing.

** NOTE TO SPECIFIER ** Select the one or more of the following three optional paragraphs if required for the project. Delete if not required.

Provide prone adapters to suspend the targets so their top edges are approximately 24 inches (610 mm) above the floor.

Provide wide target adapters with clips 18 inches (457 m) apart to carry law enforcement targets up to the full-size B21 and B27 silhouette targets without backers.

Targets travel at an average speed of 5 feet per second and stop within plus or minus one inch of their designated intermediate and terminal stops and be within this longitudinal distance of each other at designated stops.

Design Requirements: Systems designed to assure long service life with minimum service when operated full-time for the class of service specified.

Trolley wire is 11-gage galvanized steel wire and is strung between a terminal stop at the target line and a stop at the firing line. Provide with tension adjustment device for trolley wire and tension so it has sag of 6 to 9 inches (152 to 229 mm) from the horizontal.

Target-carrier car consists of a steel chassis with four ball-bearing wheels that ride on the trolley wire and is provided with a vertical recess into which target spindles may be attached. Stabilizing member shall seat into a mating member at terminal stop and provide a means for attachment of puller cords.

Terminal stop consists of a bracket for attachment and provide a means for attaching the trolley wire, a mating member for seating against the carrier-car stabilizing member and turnaround ball-bearing pulleys for puller cords.

Firing-line stop consists of a ball-bearing pulley assembly that terminates the retrieval travel of the carrier car and redirects the puller cord towards the drive unit and also provides a means for attachment and tension adjustment of the trolley wire.

Drive unit provides the power for traveling the carrier car. Provided with brackets for mounting to lateral member across the range near the firing line. Provide a cushioned stop for terminating the return travel of the carrier car. Unit provided with a removable molded ABS cover for service access with the number of the shooting point on its rear face.

Provide drive units with an entrance box with knockouts for connection to the 115 vac electrical power. Each drive unit shall be provided with individual overload protection.

Provide system with puller cord consisting of 1/8-inch (3 mm) aircraft cable.

Model CTC-D, Target Carrier System: Manually operated trolley-wire type. Equipment intended for full-time activities with mid-range handgun ammunition and be able to withstand occasional impacts from misdirected bullets from proper courses of fire when carrier cars are at the target lines. Front exposed surfaces of carrier, rail hangers and stops shall be able to withstand occasional direct impacts of all ammunition that may be fired by most handguns.

Functional Requirements: System capable of transporting all bull's eye and silhouette targets up to and including the B29 and B30 silhouette targets with or without cardboard backers.

Provide an offhand target holder for each system that will suspend targets for handgun shooting so that their top edge will be approximately 70 inches (1778 mm) above the floor. It shall securely hold the targets and quickly release them when desired for changing.

** NOTE TO SPECIFIER ** Select one of the following two optional paragraph(s) as may required for the project. Delete if not required.

Provide a prone target holder or each system to suspend targets so top edge will be approximately 18 inches (457 mm) above the floor for prone shooting and rifle targets. Holders shall be of the quick-release type.

Provide wide target holders for full-size police silhouette targets consisting of two target-holding clips located 18 inches (457 mm) apart and connected to a common descender.

Design Requirements: Design system to assure long service life with minimum service when operated full-time for the class of service specified.

Trolley wire is 11-gage galvanized steel wire strung between a terminal stop at the target line and a stop at the firing-line. Provide with a tension adjustment so that the maximum sag of 6 inches at center of range.

Carrier car consists of a steel chassis with four ball-bearing wheels that ride on the trolley wire and provided with a vertical recess into which target spindles may be attached. Provide carrier with a stabilizing member those seats into a mating member at the terminal stop and intermediate stops with a means for attachment of the puller cords.

Terminal stop consists of a bracket for attachment. Provide stop with a means of attaching trolley wire and a mating member for seating against carrier-car stabilizing member and turnaround ball-bearing pulleys for puller cords.

Firing-line stop consists of a ball-bearing pulley assembly that terminates the retrieval travel of the carrier car and redirects the puller cord towards the hand wheel. It shall also provide a means for attachment and tension adjustment on the trolley wire.

Provide hand wheel for manually traveling carrier car. Support hand wheel in an assembly that provides a bearing in a mounting block for attachment.

Provide suitable ball-bearing pulley assemblies for directing the puller cord from the firing line stop to the hand wheel assembly and puller cord for rigging the system. Puller cord shall be low stretch specially fabricated for this service and shall be 0.11 inch (2.7 mm) diameter, 8 strand, open weave, polypropylene with bonded fiberglass core.

** NOTE TO SPECIFIER ** Select the following optional paragraph if required for the project. Delete if not required.

Provide up to two intermediate stops with the same stopping features of the terminal stops. Stops shall be movable into and out of the paths of target cars by manually setting them and shall mount onto brackets dropped from the ceiling or to lateral members across the range.

Model DP65V, Portable Ground or Overhead Mounted Pursuit Target System with Variable Speed Control: (Running Man Target System)

Provide complete with all required components to set up and operate a target on a standard beam-style track.

Design so all components can be quickly attached to a standard steel I-beam track using ordinary hand tools with no track drilling to assemble. Track may be permanently mounted on the range or it can be portable.

Moving target components (excluding the track) are fully portable and easily carried by one person.

Set-up time onto a previously installed track takes about 15 minutes. Any of the components can be removed from the track in a few minutes for servicing, replacement, or to secure the range overnight.

Drive unit operates from 117/230 VAC, 60/50 HZ, single phase power. Drive unit power cord is equipped with a NEMA 5-15P 3-pin grounding plug for convenient connection to the power source.

Control Console provides the operator with speed control, forward and reverse direction selection, and start/stop. Travel direction and stop location of the target are determined by the operator on the Control Console.

System includes electrical dynamic braking which causes the target to stop instantly from low speed and within approximately 1 foot (0.3 meters) at high speed.

Target travel direction can be reversed at any point along the track without first commanding it to stop.

Target carrier is equipped so a lath or similar material, to which cardboard target backing is attached, can be mounted onto the carrier. It is capable of handling targets of the Army Type E/F size or smaller.

Moving target components can be attached to either the front or the back side of the track. The drive unit can be located at either end of the track. System can be set up with the target above the track, or with the target below the track if suspended. Conversion from one form to another is accomplished in about 15 minutes, not including track installation.

** NOTE TO SPECIFIER ** Select one the following three optional paragraphs if required and delete those not required.

Provide system to allow two independent moving targets to operate on one track simultaneously without interference.

Provide a second system to run on the back side of the beam with separate controller unit.

Provide a second target carrier to run in conjunction with the existing carrier.

Covers and shields are utilized to protect the components from direct exposure to rain and snow.

System is not self armored and must be protected from live fire by a baffle, short berm or wall.

Model DP29, Portable Ground or Overhead Mounted Pursuit Target System with DC Variable Speed Control:

Provide complete with all required components to set up and operate a target on a standard beam-style track.

Moving target components (excluding the track) are fully portable and easily carried by one person.

Drive unit operates from 117/230 VAC, 60/50 HZ, single phase power. Drive unit power cord is equipped with a NEMA 5-15P 3-pin grounding plug for convenient connection to the power source.

Rangemaster 9000 Control Console provides the operator with speed control, forward and reverse direction selection, and start/stop. Travel direction and stop location of the target are determined by the operator on the Control Console.

System includes electrical dynamic braking which causes the target to stop instantly from low speed and within approximately 1 foot (0.3 meters) at high speed.

Target travel direction can be reversed at any point along the track without first commanding it to stop.

** NOTE TO SPECIFIER ** Select one of the following three optional paragraphs if required and delete those not required.

Provide system to allow for tandem operation of target carriers on a single drive unit.

Provide a second system to run on the back side of the beam with separate controller unit.

Provide a second target carrier to run in conjunction with the existing carrier {parallel}

Moving target components can be attached to either the front or back side of the track. Drive unit can be located at either end of the track. System can be set with target above the track, or with target below the track if suspended. Conversion from one form to another is accomplished in about 15 minutes, not including track installation.

Covers and shields are utilized to protect components from direct exposure to rain and snow.

System is not self armored and must be protected from live fire by a baffle, short berm or wall.

AUDIO/VISUAL COMMUNICATION SYSTEMS

** NOTE TO SPECIFIER ** Audio visual communications systems are available to provide communications to shooters that improve the overall safety of the range. Select the type(s) required and delete those not required.

Model MC65 Sight Light Illuminator: Provides optimum lighting of the weapon sights. Provides shadowless/glareless light in the general area of the sights with a controllable intensity.

Provide a separate fixture for each shooter located on the cross member that interconnects the shooting stalls with the target retrieval system drive units. Mount below the target system to eliminate shadows.

Each fixture contains an incandescent lamp in a receptacle and a dimmer switch. The light is totally concealed but illuminates the area through the opening on the base of the fixture. Dimmer switch is inside of the fixture with control knob protruding on the base where it is easily reached by the shooter.

Opening is covered with hardware cloth guard, allowing light to exit but keeping spent brass from semi automatic firearms from breaking the bulb.

Each fixture is housed in an 18-gauge welded steel case with a cream semi-gloss finish.

Each fixture is powered from the target retrieval system or an available outlet.

Provide a flexible armored cable with each fixture to connect to the entrance box of the corresponding target retrieval system drive unit or other receptacle.

Recommended lamp size is 60-watt incandescent.

Dimmer is a UL listed solid-state, rated at 600 watts and incorporates an on-off switch.

Model EM15 Signal Light System: Range condition is shown by signal light system visible to all shooters in which RED indicates that no shooting is allowed, AMBER indicates the shooters should be alert for a change, and GREEN indicates the range is secure and shooting may take place according to the Rangemaster's instructions.

System provided with a bank of lights for each shooting point and a master control at the Rangemaster's station, a feedback loop consisting of a Rangemaster call button at each shooting point and signal-light terminals for individual shooters with a signal-light control at the Rangemaster's station.

** NOTE TO SPECIFIER ** Select the following optional paragraph if required and delete if not required.

Provide with signal light system that incorporates a firing-line security system so that all condition lights are switched to red if anyone advances downrange across the firing line. System consists of a photoelectric surveillance system across each shooting stall plus the necessary interfacing electronics.

System consists of a master control panel from which the Rangemaster may select the condition lights. Signals from the control panel shall be transmitted to the signal light terminals by means of low-voltage lines.

Control panel includes switches so the Rangemaster may select the condition lights for individual terminals or may operate all in-unison.

Rangemaster call button in each signal light terminal shall cause the red signal light in that shooting point to illuminate and simultaneously illuminate a red indicator light on the master control panel that identifies the shooting point. This condition remains until canceled at the call button.

Model EM30, Firing Line Security System: System monitors a violation of the firing line (someone advancing downrange from the firing line). System consists of a photo-electric surveillance system that will sound an audible alarm within the range to warn those occupying the range of the danger.

System provided with a master control panel for the firing line security system with an indicator light to show when the system is armed, a warning light to show when violated, a reset button, and an audible alarm on/off switch.

When system is used with any electronic target system, the targets will cease transport and return to the edge position when a security breach has occurred

** NOTE TO SPECIFIER ** Select the following optional paragraph if required and delete if not required.

Provide system with down range doors tied to the security system so if the system is activated, and a door is open, the security alert will engage.

Audio Communications System (Two-Way Speaker Type - Multi Channel Master System): System is a selective type that provides two-way audio communications between the Rangemaster and the range room and enables the Rangemaster to select any one of up to ten individual channels.

** NOTE TO SPECIFIER ** Select one of the following four Model paragraph as required and delete those not required.

Model EG58 Audio Communications System (Two-Way Speaker Type - Ten Channel Master System)

Model EG60 Audio Communications System (Two-Way Speaker Type - Twenty Channel Master System)

Model EG71 Audio Communications System (Two-Way Speaker Type - Thirty Channel Master System)

Model EG61 Audio Communications System (Two-Way Speaker Type - Forty Channel Master System)

Functional Requirements: Master control panel enables the system to be turned on or off, the channels selected, and talk condition or listen condition selected.

Each channel is represented by a mode switch, which allows that channel to be turned off, turned on for individual operation, or turned on for in-unison operation with other channels. A separate on/off switch shall control all channels placed in the in-unison mode.

Master control has a talk/listen condition switch. When in the talk position, the Rangemaster is heard on all channels in the in-unison mode.

When the condition switch is in the listen position, the Rangemaster will hear a voice spoke into any one channel whose mode switch is on. He will not hear from channels that are off or in-unison.

Hardware Requirements: System consists of a master station and individual audio terminals.

Master station consists of a control field which is mounted among the other master controls (if any) and which contains the operational controls. It shall also provide the amplifier and power supply.

Each channel provided with an audio terminal that consists of both speaker and microphone capabilities that are housed for surface mounting on walls or ceiling as indicated.

System shall be compatible in electrical characteristics, mounting requirements and appearance to the other equipment in specified in this Section.

Model EG66, Speakers Stations for use with Master Communications System:

Two-Way Speaker Type to provide two-way audio communications between the Rangemaster and the individual channels.

Functional Requirements: Controlled through master control panel that enable stations to be turned on or off, channels selected, and talk condition or listen condition selected.

Each channel shall be represented by a mode switch which shall allow that channel to be turned off, turned on for individual operation or turned on for in-unison operation with other channels.

Hardware Requirements: Consist of individual audio terminals.

Each channel shall have an audio terminal consisting of both speaker and microphone capabilities and housed for surface mounting on walls or ceiling as indicated.

System shall be compatible in electrical characteristics, mounting requirements and appearance to other equipment specified in this Section.

Model EG67, Ceiling Speakers Stations for use with Master Communications System:

Paging Speaker Type to provide one-way audio communications between the Rangemaster and the individual channels.

Functional Requirements: Controlled through master control panel that enable stations to be turned on or off, channels selected, and talk condition selected.

Each channel shall be represented by a mode switch which shall allow that channel to be turned off, turned on for individual operation or turned on for in-unison operation with other channels.

Hardware Requirements: Consist of individual audio terminals.

Each channel shall have an audio terminal consisting of both speaker and housed for surface mounting on walls or ceiling as indicated.

System to be compatible in electrical characteristics, mounting requirements and appearance to other equipment specified in this Section.

Model EG55, Stereo Ear Protector System:

Headset. Consists of an adjustable fitting headband and two ear cups.

Equipped with soft cup pads for extra comfort and stability when worn in the over-the-head position. Cups are filled with special acoustic fibers.

Acetyl Headband is designed for comfort with initial pressure that is high to ensure best fit, but gradually relaxes after about seven minutes to a more comfortable level.

Built-in Electronics. Ear Protector has built-in electronics that are battery operated.

Built-in electronics automatically zero-in on sounds in the 800-4000 Hz range. (This is the normal frequency range of the human voice.).

Provide with adjustable volume control that amplifies any sound in these frequencies, as much as 10 dB up to a maximum safe 82 dB level.

Sounds above or below voice range are attenuated from an external sound level of between 82-102 dB to a comfortable ear cup level of 82 dB.

When external noises reach above the 102 dB level, the electronics are shut down for protection. Shut down response time is .5 mili-sec (1/2000 of a second) the fastest response time available.

Battery Operated, using a low cost 9-volt battery with a life expectancy of approximately 290 hours of continuous use.

Provided with a unique six-hour automatic shut-off feature for maximum battery life.

Replacement of battery can be performed within a matter of seconds without damage to electronic circuitry.

CONTROL SYSTEMS

** NOTE TO SPECIFIER ** Control systems are available to provide programmed courses and scenarios to improve the skills of the shooters and that also improves the overall safety of the range. Controls are available that provide manual and automatic (programmed) operation of the firing range. Select the type(s) required and delete those not required.

Model RM9000 Master Control: Provide complete manual and automatic (programmed) operation of the firing range.

General Description: Master control consists of required hardware and software components necessary to carry out the functions described in this specification.

Hardware based on an IBM PC compatible computer with additional components and assemblies as necessary.

Master control software operates in the Windows XP environment.

Functional Description: Master control shall provide the following functions:

Manually or automatically control the full potential of all target types required including face-left, face-right, random face, conceal, re-expose last face, pop-up, swing-up, swing-out, hit fall, hit return, hit sensitivity adjust, target illumination, clear hits, hit scores, and target movements such as downrange positioning and return for monorail target systems and lateral direction and speed control for moving target systems.

Allow entry, editing, permanent storage, retrieval, execution and deletion of conventional courses of fire (one shooter/one target) as well as advanced programs (one shooter/multiple targets).

Permit starting, stopping, pausing, continuing, and restarting programmed courses and scenarios.

Stop course in progress in the event of an emergency determined by the operator or automatically upon an encroachment into the secure area protected by the optional security system.

Download stored programs to selected individual control units.

Display targets graphically on the monitor in a manner representative of range layout.

Range display can be zoomed to any level desired by the operator.

Allow the writing of programmed scenarios to perform automatic, timed target operation.

Sections of programs can be skipped, repeated, and executed individually.

10)

Provide on-line help through a HELP menu.

11)

Provide dialog boxes, menus, buttons and other boxes as would be normally associated with Windows-based software.

12)

Provide the following menu items as a minimum:

Controls - selects various target devices and target control functions.

Program - controls all program functions including buttons for Run, Pause, Reset, Step, and Close. Display Status, Elapsed Time, Step, Instruction, Comment, Delay, Cycle.

Signals - controls signal light and Rangemaster call functions.

Security - controls firing line and door security functions.

View - allows zoom in/out and simulation views.

Help - on-line help system functions.

13)

Minimum System Requirements: The master control shall consist of the following as a minimum:

IBM PC compatible desktop computer.

Pentium IV processor, 1.7 MHz.

256 MB RAM.

40 GB hard disk drive.

CD- ROM.

VGA Monitor, 17 inch.

1 serial and 1 parallel port.

Microsoft Windows XP.

Range Interface Adaptor.

PC to RIA serial cable.

Model RM9000-LT Master Control: Portable version of Model RM9000. Portable master control shall be providing complete manual and automatic (programmed) operation of the firing range.

Model RM10000 Master Control: Provides complete manual and automatic (programmed) operation of the firing range.

General Description: Master control shall consist of required hardware and software components necessary to carry out functions described in this specification.

Hardware is based on an IBM PC compatible computer with additional components and assemblies as necessary.