** NOTE TO SPECIFIER ** Delete items below not required for project. Bar Grilles. Perforated Sheet Metal Grilles. Eggcrate Grilles. Waterjet Cut Custom Grilles. Round Perforated Grilles. Progressive Louvers. Radiator Covers and enclosures. Equipment Plates. MANUFACTURERS Acceptable Manufacturer: ** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions. Substitutions: Not permitted. Requests for substitutions will be considered in accordance with provisions of Section . ** NOTE TO SPECIFIER ** Select grilles and plates as required from the following products. Delete the item(s) not required for the project. PRODUCTS ** NOTE TO SPECIFIER ** Delete all but one of the following six paragraphs describing grille core types; if more than one type or finish is required, indicate bar grille types and finish on the drawings or the attached grille schedule. Standard thicknesses are indicated however, all products are available in any thickness upon request. Bar Grilles: ** NOTE TO SPECIFIER ** For Type AG10 core insert required bar spacing - 1/4 inch (6.5 mm) (6.5 mm), 3/8 inch, and 1/2 inch (12.7 mm) centers are available. Core: Type AG10; 1/8 inch (3 mm) thick by 3/4 inch (19 mm) deep rectangular metal bars spaced ___ inch on center, interlocked and welded to 1/8 inch (3 mm) thick by 1/2 inch (12.7 mm) deep rectangular metal bar crosspieces spaced 10 inches (25.4 mm) on center. Metal and finish as follows: ** NOTE TO SPECIFIER ** Select material finish and color required. Delete the materials and finishes not required. Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Brass: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Stainless Steel: Satin Finish No. 4. Mirror Polish No.8 finish. Core: Type AG20; 3/4 inch (19 mm) deep rectangular metal bars, cross-section flared 15 degrees one side, 1/4 inch (6.5 mm) thick across flared face tapering to 1/8 inch (3 mm) at bottom, spaced 1/2 inch (12.7 mm) on center, interlocked and welded to 1/8 inch (3 mm) thick by 1/2 inch (12.7 mm) deep rectangular metal bar crosspieces spaced 10 inches (25.4 mm) on center. ** NOTE TO SPECIFIER ** Select material finish and color required. Delete the materials and finishes not required. Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Core: Type AG30; 3/4 inch (19 mm) deep rectangular metal bars, cross-section flared 15 degrees both sides, 1/4 inch (6.5 mm) thick across flared face, spaced 1/2 inch (12.7 mm) on center, interlocked and welded to 1/8 inch (3 mm) thick by 1/2 inch (12.7 mm) deep rectangular metal bar crosspieces spaced 10 inches (25.4 mm) on center. ** NOTE TO SPECIFIER ** Select material finish and color required. Delete the materials and finishes not required. Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Core: Type AG40; 1/8 inch (3 mm) thick by 3/4 inch (19 mm) deep rectangular metal bars, ends milled to 16-degree bevel, spaced 3/8 inch (9.5 mm) on center, interlocked and welded at 16-degree angle from perpendicular to 1/8 inch (3 mm) thick by 1/2 inch (12.7 mm) deep rectangular metal bar crosspieces spaced 10 inches (25.4 mm) on center. ** NOTE TO SPECIFIER ** Select material finish and color required. Delete the materials and finishes not required. Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Brass: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Stainless Steel: Satin Finish No. 4. Mirror Polish No.8 finish. Core: Type AG50; 3/4 inch (19 mm) deep rectangular metal bars, cross-section flared 15 degrees on side, 3/16 inch (4.7 mm) thick across flared face, spaced 1/2 inch (12.7 mm) on center, interlocked and welded to 1/8 inch (3 mm) thick by 1/2 inch (12.7 mm) deep rectangular metal bar crosspieces spaced 10 inches (25.4 mm) on center. ** NOTE TO SPECIFIER ** Select material finish and color required. Delete the materials and finishes not required. Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Core: Type AG60; 3/4 inch (19 mm) deep rectangular/round metal bars, cross-section flared into a 1/4 inch (6.5 mm) round, spaced 1/2 inch (12.7 mm) on center, interlocked and welded to 1/8 inch (3 mm) thick by 1/2 inch (12.7 mm) deep rectangular metal bar crosspieces spaced 10 inches (25.4 mm) on center. ** NOTE TO SPECIFIER ** Select material finish and color required. Delete the materials and finishes not required. Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. ** NOTE TO SPECIFIER ** Select frame type required from the following frame paragraphs. Delete the frame types not required. Delete all three Frame, Mitered Corner and Curved Section paragraphs if frame is not required. No Frame: Weld anchor tabs Type 115 Frame: Type A, semi-concealed; 7/8 inch (22.2 mm) by 1/2 inch (12.7 mm) by 1/8 inch (3 mm) cross-section angle, inside of 1/2 inch (12.7 mm) leg welded to back side of grille at crosspieces. Frame: Type B, full face frame; 3/4 inch (19 mm) by 3/4 inch (19 mm) by 1/8 inch (3 mm) cross-section angle, back side of one angle leg welded to edge of grille at crosspieces, 3/4 inch (19 mm) face frame. Frame: Type C, reinforced full face frame; 3/4 inch (19 mm) by 7/8 inch (22.2 mm) by 5/8 inch (15.9 mm) by 1/8 inch (3 mm) cross-section zee, inside of 5/8 inch (15.9 mm) leg welded to back side of grille at crosspieces, 3/4 inch (19 mm) face frame. Frame: Type D, full face frame; 1 inch (25 mm) by 3/4 inch (19 mm) by 3/16 inch (4.6 mm) cross-section angle, back side of one angle leg welded to edge of grille at crosspieces, 3/4 inch (19 mm) face frame. Frame: Type E, full face frame; 3/4 inch (19 mm) by 3/4 inch (19 mm) by 3/16 inch (4.6 mm) cross-section angle, back side of one angle leg welded to edge of grille at crosspieces, 3/4 inch (19 mm) face frame. Frame: Type F, full face frame; 1/2 inch (12.5 mm) by 3/4 inch (19 mm) by 3/16 inch (4.6 mm) cross-section angle, back side of one angle leg welded to edge of grille at crosspieces, 3/4 inch (19 mm) face frame. Frame: Type G, semi-concealed; 3/4 inch (19 mm) by 1/8 inch (3 mm) cross-section, back side of leg welded to edge of grille at crosspieces. Frame: Type J, semi-concealed; 7/8 inch (22.2 mm) by 1/2 inch (12.7 mm) by 1/8 inch (3 mm) cross-section angle, inside of 1/2 inch (12.7 mm) leg welded to back side of grille at crosspieces, with a 1 inch (25.5mm) spackling frame. ** NOTE TO SPECIFIER ** Select horizontal or vertical installation from the following two paragraphs. Delete both paragraphs if not required. Mitered Corner Sections: Fabricate welded mitered corner sections to match sections of straight bar grille units for horizontal installation. Mitered Corner Sections: Fabricate welded mitered corner sections to match sections of straight bar grille units for vertical installation. ** NOTE TO SPECIFIER ** Select horizontal or vertical installation from the following two paragraphs. Delete both paragraphs if not required. Curved sections not available for Type AG40 core. Curved Sections: Fabricate concave curved sections in accordance with supplied templates to match sections of straight bar grille units for horizontal installation. Curved Sections: Fabricate concave curved sections in accordance with supplied templates to match sections of straight bar grille units for vertical installation. Curved Sections: Fabricate convex curved sections in accordance with supplied templates to match sections of straight bar grille units for horizontal installation. Curved Sections: Fabricate convex curved sections in accordance with supplied templates to match sections of straight bar grille units for vertical installation. ** NOTE TO SPECIFIER ** Delete following paragraph if access door is not required. If required select access operation and indicated opening size. Concealed Access Door: Provide concealed access door matching core at locations indicated. Pivot hinged access. Lift out access. Size ___________. ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. Type 114 tabs are for use with frame types A, C or J, Type 115 tabs are for use with frameless core or frame type B, D, E, F; method in third paragraph can be used with frame types A or C. Fastening on face of frame are available on Frame Type B and Frame Type C. Drop in frames for Type G do not require fastening devices. Consult manufacturer's catalog for additional Information. Fastening Devices: Weld anchor tabs Type 114, with countersunk pre-drilled fastener holes, for installation of grilles. Fastening Devices: Weld anchor tabs Type 115, with countersunk pre-drilled fastener holes, for installation of grilles. Fastening Devices: Pre-drill countersunk fastener holes in concealed surface of frame at indicated spacings for installation of grilles. ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. Fill in size if specified here. Coordinate with drawings. Bar Grille Size: __________ height by ___________ width. Bar Grille Sizes: Heights and widths indicated on Drawings. Bar Grille Sizes: Heights and widths indicated on Grille Schedule. Perforated Sheet Metal Grilles: ** NOTE TO SPECIFIER ** Delete all but one of the following 28 paragraphs describing perforated sheet metal grille patterns; if more than one pattern or finish is required, indicate patterns and finish on the drawings or the attached grille schedule. Pattern: Square Link, Number 200. Pattern repeat 1 inch (25.5mm), open area 38 percent. Pattern repeat 1-1/4 inches (31.8 mm), open area 40 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 49 percent. Pattern repeat 2-1/4 inches (57.2 mm), open area 56 percent. Pattern: Parquet, Number 201. Pattern repeat 1-3/16 inches (30.2 mm), open area 35 percent. Pattern: Grecian, Number 202. Pattern repeat 1-1/4 inches (31.8 mm), open area 39 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 58 percent. Pattern: Honeycomb, Number 203. Pattern repeat 3/4 inch (19 mm), open area 50 percent. Pattern: Clover Leaf, Number 204. Pattern repeat 1/2 by 3/16 inch (12.5 by 4.8 mm), open area 51 percent. Pattern repeat 1/2 by 1/4 inch (12.5 by 6.5 mm), open area 52 percent. Pattern repeat 1 inch (25.5 mm), open area 50 percent. Pattern: Diamond, Number 205. Pattern repeat 1/4 inch (6.5 mm) with 1/4 inch (6.5 mm) bar, open area 25 percent. Pattern repeat 1/2 inch (12.5 mm) with 1/4 inch (6.5 mm) bar, open area 45 percent. Pattern repeat 3/4 inch (19 mm) with 1/4 inch (6.5 mm) bar, open area 56 percent. Pattern repeat 1 inch (25.5 mm) with 1/4 inch (6.5 mm) bar, open area 64 percent. Pattern: Maltese, Number 206. Pattern repeat 15/16 inch (23.8 mm), open area 38 percent. Pattern repeat 1-3/4 inches (44.45 mm), open area 45 percent. Pattern: Shell, Number 207. Pattern repeat 5/8 inch (15.9 mm), open area 48 percent. Pattern repeat 1-1/8 inches (28.5 mm), open area 56 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 72 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 84 percent. Pattern: Lattice, Number 208. Pattern repeat 1/4 inch (6.5 mm) with 1/4 inch (6.5 mm) bar, open area 25 percent. Pattern repeat 1/2 inch (12.7 mm) with 1/4 inch (6.5 mm) bar, open area 45 percent. Pattern repeat 3/4 inch (19 mm) with 1/4 inch (6.5 mm) bar, open area 56 percent. Pattern repeat 1 inch (25.5 mm) with 1/4 inch (6.5 mm) bar, open area 64 percent. Pattern: Half Shell, Number 209. Pattern repeat 1-5/16 inches (33.3 mm), open area 55 percent. Pattern repeat 1-3/4 inches (44.45 mm), open area 68 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 80 percent. Pattern: School Slot, Number 210. Pattern repeat 1/4 inch (6.5 mm) by 1 inch (25.5 mm), open area 35 percent. Pattern repeat 5/16 inch (7.9 mm) by 1-3/8 inch (35 mm), open area 43 percent. Pattern: Egyptian, Number 211. Pattern repeat 1 inch (25.5mm), open area 40 percent. Pattern repeat 2 inches (51 mm), open area 55 percent. Pattern: Straight Hole, Number 212. Pattern repeat 1/4 inch (6.5 mm) diameter with 1/2 inch (12.7 mm) centers, open area 21 percent. (other sizes available). Pattern: Staggered Hole, Number 213. Pattern repeat 1/4 inch (6.5 mm) diameter with 1/2 inch (12.7 mm) centers, open area 23 percent. (other sizes available). Pattern: Gothic, Number 214. Pattern repeat 1-1/16 inches (27 mm), open area 58 percent. Pattern: Brick, Number 215. Pattern repeat 1/4 inch (6.5 mm) by 1 inch (25.5 mm), open area 35 percent. Pattern repeat 3/8 inch (9.5 mm) by 1 inch (25.5 mm), open area 43 percent. Pattern: Square on Diamond, Number 216. Pattern repeat 1/2 inch (12.5 mm), open area 45 percent. Pattern repeat 3/4 inch (19 mm), open area 56 percent. Pattern repeat 1 inch (25.5 mm), open area 64 percent. Pattern: Triangle and Clover, Number 217. Pattern repeat 1-1/4 inches (31.8 mm), open area 23 percent. Pattern: Cross Link, Number 218. Pattern repeat 1-1/2 inches (38.1 mm), open area 45 percent. Pattern: Windsor, Number 219. Pattern repeat 1-9/16 inches (39.68 mm), open area 48 percent. Pattern repeat 2 inches (51 mm), open area 55 percent. Pattern: Classic, Number 220. Pattern repeat 1-5/8 inches (41.27mm) by 1-5/16 inches (33.75 mm), open area 58 percent. Pattern repeat 2 inches (51 mm) by 1-3/4 inches (44.5 mm), open area 72 percent. Pattern: Tear Drop, Number 221. Pattern repeat 1-3/4 inches (44.5 mm) by 1-9/16 inches (39.68 mm), open area 66 percent. Pattern: Circle Link, Number 222. Pattern repeat 2-1/2 inch (12.7 mm) round, open area 65 percent. Pattern: Mosaic, Number 223. Pattern repeat 1-1/32 inches (26.19 mm), open area 54 percent. Pattern: Imperial, Number 224. Pattern repeat 1-7/8 inches (47.6 mm), open area 47 percent. Pattern: Majestic, Number 225. Pattern repeat 1 inch (25.5 mm), open area 40 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 52 percent. Pattern repeat 2-1/4 inches (57.2 mm), open area 64 percent. Pattern: Cathedral, Number 226. Pattern repeat 2-1/4 inches (57.15 mm) by 2-3/16 inches (55.5 mm), open area 57 percent. Pattern: Petals, Number 227. Pattern repeat 1-7/8 inches (47.6 mm), open area 52 percent. Pattern: Weave 228. Pattern repeat 1/2 inches (12.5 mm) by 1/2 inches (12.5 mm), open area 45 percent. Pattern: Orient, Number 229. Pattern repeat 2 inches (51 mm), open area 48 percent. Pattern: Pinwheel, Number 230. Pattern repeat 1-3/4 inches (44.5 mm), open area 58 percent. Pattern: Shuriken, Number 231. Pattern repeat 2 inches (51.5 mm), open area 33 percent. Pattern: Bubbles, Number 232. Random opening pattern, open area varies. Pattern: Kauai, Number 233. Pattern repeat 2-3/4 inches (69.8 mm), open area 58 percent. Pattern: Pebbles, Number 234. Random opening pattern, open area varies. Pattern: Cubic, Number 235. Random opening pattern, open area varies. ** NOTE TO SPECIFIER ** Select the material and thickness required from the following paragraphs. Delete the paragraphs not required. Standard thicknesses are indicated however; all products are available in any thickness upon request. Material: ** NOTE TO SPECIFIER ** Aluminum is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Aluminum, __ inch thick. ** NOTE TO SPECIFIER ** Brass is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Brass, __ inch thick. ** NOTE TO SPECIFIER ** Bronze is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Bronze, __ inch thick. ** NOTE TO SPECIFIER ** Stainless Steel is available in a 1/16 inch minimum thickness and a 14 gauge maximum thickness. Select thickness required below. Stainless Steel, __ inch thick. ** NOTE TO SPECIFIER ** Steel is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Steel, __ inch thick. ** NOTE TO SPECIFIER ** Delete one of the following two paragraphs. Delete both if access door is not required. Access Door: Fabricate concealed, hinged access door matching grille pattern at locations indicated. Access Door: Fabricate pivoting access door matching grille pattern at locations indicated. ** NOTE TO SPECIFIER ** Delete three of the following four paragraphs. The first through fourth paragraphs specify fastening types 105, 106, 107, and 107A, respectively. Fastening Devices: Pre-drill countersunk fastener holes in surface of frame at indicated spacings for installation of grilles. Fastening Devices: Weld 1/2 inch (12.7 mm) leg of 1/2 inch (12.7 mm) by 3/4 inch (19 mm) by 1/8 inch (3 mm) cross-section angle to concealed surface of grille, with countersunk pre-drilled fastener holes at indicated spacings in 3/4 inch (19 mm) leg, for reinforcement and installation of grille. Fastening Devices: Weld edge of 3/4 inch (19 mm) by 1/8 inch (3 mm) cross-section bar to concealed surface of grille, with countersunk pre-drilled fastener holes at indicated spacings in flat surface of bar, for reinforcement and installation of grille. Fastening Devices: Weld top edge of 3/4 inch (19 mm) leg of 1/2 inch (12.7 mm) by 3/4 inch (19 mm) by 1/8 inch (3 mm) cross-section angle to concealed surface of grille, with countersunk pre-drilled fastener holes at indicated spacings in 1/2 inch (12.7 mm) leg, for reinforcement and installation of grille. ** NOTE TO SPECIFIER ** Delete one of the following two paragraphs. Fill in size if specified here. Coordinate with drawings or the attached grille schedule. Perforated Sheet Metal Grille Size: __________ height by ___________ width. Perforated Sheet Metal Grille Size: Heights and widths indicated on Drawings. Perforated Sheet Metal Grille Size: Heights and widths indicated on Grille Schedule. ** NOTE TO SPECIFIER ** Select finish required. If more than one finish is required indicated on the drawings or the attached grille schedule. Finish: Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Brass: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Stainless Steel: Satin Finish No. 4. Mirror Polish No.8 finish. Steel: Prime finish. Powder Coat Colors (As selected by Architect). Eggcrate Grille: ** NOTE TO SPECIFIER ** Delete all but one of the following ten paragraphs describing eggcrate grille sizes; if more than one size or finish is required, indicate patterns and finish on the drawings or the attached grille schedule. Cell Size: 1/2 inch (12.5 mm) square by 1/2 inch (12.5 mm) depth. Cell Size: 3/4 inch (19 mm) square by 3/4 inch (19 mm) depth. Cell Size: 1 inch (25.5 mm) square by 1 inch (25.5 mm) depth. Cell Size: 1-1/4 inches (31.8 mm) square by 1-1/4 inches (31.8 mm) depth. Cell Size: 1-1/2 inches (38 mm) square by 1-1/2 inches (38 mm) depth. Cell Size: 1-3/4 inches (44.5 mm) square by 1-3/4 inches (44.5 mm) depth. Cell Size: 2 inches (51 mm) square by 2 inches (51 mm) depth. Cell Size: 2-1/4 inches (57.2 mm) square by 2-1/4 inches (57.2 mm) depth. Cell Size: 2-1/2 inches (63.5 mm) square by 2-1/2 inches (63.5 mm) depth. Cell Size: 2-3/4 inches (70 mm) (70 mm) square by 2-3/4 inches (70 mm) depth. Cell Size: 3 inches (76 mm) square by 3 inches (76 mm) depth. ** NOTE TO SPECIFIER ** Select finish required. If more than one finish is required indicated on the drawings or the attached grille schedule. Standard thicknesses are indicated however; all products are available in any thickness upon request. Material and Finish: Material is 1/8 inch (3.2 mm) thick. Aluminum: Satin No. 4 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Brass: Satin Finish No. 4. Bronze: Satin Finish No. 4. Stainless Steel: Satin Finish No. 4. ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. Fill in size if specified here. Coordinate with drawings or the attached grille schedule. Eggcrate Grille Size: __________ height by ___________ width. Eggcrate Grille Size: Heights and widths indicated on drawings. Eggcrate Grille Size: Heights and widths indicated on Grille Schedule. ** NOTE TO SPECIFIER ** Select frame type required from the following frame paragraphs. Delete the frame types not required. Delete all three paragraphs if frame is not required. Frame: Type A, semi-concealed; 7/8 inch (22.2 mm) by 1/2 inch (12.7 mm) by 1/8 inch (3 mm) cross-section angle, inside of 1/2 inch (12.7 mm) leg welded to back side of grille at crosspieces. Frame: Type B, full face frame; 3/4 inch (19 mm) by 3/4 inch (19 mm) by 1/8 inch (3 mm) cross-section angle, back side of one angle leg welded to edge of grille at crosspieces, 3/4 inch (19 mm) face frame. Frame: Type C, reinforced full face frame; 3/4 inch (19 mm) by 7/8 inch (22.2 mm) by 5/8 inch (15.9 mm) by 1/8 inch (3 mm) cross-section zee, inside of 5/8 inch (15.9 mm) leg welded to back side of grille at crosspieces, 3/4 inch (19 mm) face frame. Frame: Type D, full face frame; 1 inch (25 mm) by 3/4 inch (19 mm) by 3/16 inch (4.6 mm) cross-section angle, back side of one angle leg welded to edge of grille at crosspieces, 3/4 inch (19 mm) face frame. Frame: Type E, full face frame; 3/4 inch (19 mm) by 3/4 inch (19 mm) by 3/16 inch (4.6 mm) cross-section angle, back side of one angle leg welded to edge of grille at crosspieces, 3/4 inch (19 mm) face frame. Frame: Type F, full face frame; 1/2 inch (12.5 mm) by 3/4 inch (19 mm) by 3/16 inch (4.6 mm) cross-section angle, back side of one angle leg welded to edge of grille at crosspieces, 3/4 inch (19 mm) face frame. Frame: Type G, semi-concealed; 3/4 inch (19 mm) by 1/8 inch (3 mm) cross-section, back side of leg welded to edge of grille at crosspieces. Frame: Type J, semi-concealed; 7/8 inch (22.2 mm) by 1/2 inch (12.7 mm) by 1/8 inch (3 mm) cross-section angle, inside of 1/2 inch (12.7 mm) leg welded to back side of grille at crosspieces, with a 1 inch (25.5mm) spackling frame. ** NOTE TO SPECIFIER ** Select horizontal or vertical installation from the following two paragraphs. Delete both paragraphs if not required. Mitered Corner Sections: Fabricate welded mitered corner sections to match sections of straight bar grille units for horizontal installation. Mitered Corner Sections: Fabricate welded mitered corner sections to match sections of straight bar grille units for vertical installation. ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. Type 114 tabs are for use with frame types A, C or J, Type 115 tabs are for use with frameless core or frame type B, D, E, F; method in third paragraph can be used with frame types A or C. Fastening on face of frame are available on Frame Type B and Frame Type C. Drop in frames for Type G do not require fastening devices. Consult manufacturer's catalog for additional Information. Fastening Devices: Weld anchor tabs Type 114, with countersunk pre-drilled fastener holes, for installation of grilles. Fastening Devices: Weld anchor tabs Type 115, with countersunk pre-drilled fastener holes, for installation of grilles. Fastening Devices: Pre-drill countersunk fastener holes in concealed surface of frame at indicated spacings for installation of grilles. ** NOTE TO SPECIFIER ** Waterjet cut grilles are available in all standard patterns and in custom patterns including complex shapes and specially designed patterns, such as logos and gratings in a maximum thickness of 1 inch. Artwork is required in advance. Edit the following paragraphs describing waterjet grilles including pattern, thickness, finish and size. Waterjet Cut Grilles: ** NOTE TO SPECIFIER ** Delete all but one of the following 29 paragraphs describing perforated sheet metal grille patterns; if more than one pattern or finish is required, indicate patterns and finish on the drawings or the attached grille schedule. Pattern: Square Link, Number 200. Pattern repeat 1 inch (25.5mm), open area 38 percent. Pattern repeat 1-1/4 inches (31.8 mm), open area 40 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 49 percent. Pattern repeat 2-1/4 inches (57.2 mm), open area 56 percent. Pattern: Parquet, Number 201. Pattern repeat 1-3/16 inches (30.2 mm), open area 35 percent. Pattern: Grecian, Number 202. Pattern repeat 1-1/4 inches (31.8 mm), open area 39 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 58 percent. Pattern: Honeycomb, Number 203. Pattern repeat 3/4 inch (19 mm), open area 50 percent. Pattern: Clover Leaf, Number 204. Pattern repeat 1/2 by 3/16 inch (12.5 by 4.8 mm), open area 51 percent. Pattern repeat 1/2 by 1/4 inch (12.5 by 6.5 mm), open area 52 percent. Pattern repeat 1 inch (25.5 mm), open area 50 percent. Pattern: Diamond, Number 205. Pattern repeat 1/4 inch (6.5 mm) with 1/4 inch (6.5 mm) bar, open area 25 percent. Pattern repeat 1/2 inch (12.5 mm) with 1/4 inch (6.5 mm) bar, open area 45 percent. Pattern repeat 3/4 inch (19 mm) with 1/4 inch (6.5 mm) bar, open area 56 percent. Pattern repeat 1 inch (25.5 mm) with 1/4 inch (6.5 mm) bar, open area 64 percent. Pattern: Maltese, Number 206. Pattern repeat 15/16 inch (23.8 mm), open area 38 percent. Pattern repeat 1-3/4 inches (44.45 mm), open area 45 percent. Pattern: Shell, Number 207. Pattern repeat 5/8 inch (15.9 mm), open area 48 percent. Pattern repeat 1-1/8 inches (28.5 mm), open area 56 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 72 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 84 percent. Pattern: Lattice, Number 208. Pattern repeat 1/4 inch (6.5 mm) with 1/4 inch (6.5 mm) bar, open area 25 percent. Pattern repeat 1/2 inch (12.7 mm) with 1/4 inch (6.5 mm) bar, open area 45 percent. Pattern repeat 3/4 inch (19 mm) with 1/4 inch (6.5 mm) bar, open area 56 percent. Pattern repeat 1 inch (25.5 mm) with 1/4 inch (6.5 mm) bar, open area 64 percent. Pattern: Half Shell, Number 209. Pattern repeat 1-5/16 inches (33.3 mm), open area 55 percent. Pattern repeat 1-3/4 inches (44.45 mm), open area 68 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 80 percent. Pattern: School Slot, Number 210. Pattern repeat 1/4 inch (6.5 mm) by 1 inch (25.5 mm), open area 35 percent. Pattern repeat 5/16 inch (7.9 mm) by 1-3/8 inch (35 mm), open area 43 percent. Pattern: Egyptian, Number 211. Pattern repeat 1 inch (25.5mm), open area 40 percent. Pattern repeat 2 inches (51 mm), open area 55 percent. Pattern: Straight Hole, Number 212. Pattern repeat 1/4 inch (6.5 mm) diameter with 1/2 inch (12.7 mm) centers, open area 21 percent. (other sizes available). Pattern: Staggered Hole, Number 213. Pattern repeat 1/4 inch (6.5 mm) diameter with 1/2 inch (12.7 mm) centers, open area 23 percent. (other sizes available). Pattern: Gothic, Number 214. Pattern repeat 1-1/16 inches (27 mm), open area 58 percent. Pattern: Brick, Number 215. Pattern repeat 1/4 inch (6.5 mm) by 1 inch (25.5 mm), open area 35 percent. Pattern repeat 3/8 inch (9.5 mm) by 1 inch (25.5 mm), open area 43 percent. Pattern: Square on Diamond, Number 216. Pattern repeat 1/2 inch (12.5 mm), open area 45 percent. Pattern repeat 3/4 inch (19 mm), open area 56 percent. Pattern repeat 1 inch (25.5 mm), open area 64 percent. Pattern: Triangle and Clover, Number 217. Pattern repeat 1-1/4 inches (31.8 mm), open area 23 percent. Pattern: Cross Link, Number 218. Pattern repeat 1-1/2 inches (38.1 mm), open area 45 percent. Pattern: Windsor, Number 219. Pattern repeat 1-9/16 inches (39.68 mm), open area 48 percent. Pattern repeat 2 inches (51 mm), open area 55 percent. Pattern: Classic, Number 220. Pattern repeat 1-5/8 inches (41.27mm) by 1-5/16 inches (33.75 mm), open area 58 percent. Pattern repeat 2 inches (51 mm) by 1-3/4 inches (44.5 mm), open area 72 percent. Pattern: Tear Drop, Number 221. Pattern repeat 1-3/4 inches (44.5 mm) by 1-9/16 inches (39.68 mm), open area 66 percent. Pattern: Circle Link, Number 222. Pattern repeat 2-1/2 inch (12.7 mm) round, open area 65 percent. Pattern: Mosaic, Number 223. Pattern repeat 1-1/32 inches (26.19 mm), open area 54 percent. Pattern: Imperial, Number 224. Pattern repeat 1-7/8 inches (47.6 mm), open area 47 percent. Pattern: Majestic, Number 225. Pattern repeat 1 inch (25.5 mm), open area 40 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 52 percent. Pattern repeat 2-1/4 inches (57.2 mm), open area 64 percent. Pattern: Cathedral, Number 226. Pattern repeat 2-1/4 inches (57.15 mm) by 2-3/16 inches (55.5 mm), open area 57 percent. Pattern: Petals, Number 227. Pattern repeat 1-7/8 inches (47.6 mm), open area 52 percent. Pattern: Weave 228. Pattern repeat 1/2 inches (12.5 mm) by 1/2 inches (12.5 mm), open area 45 percent. Pattern: Orient, Number 229. Pattern repeat 2 inches (51 mm), open area 48 percent. Pattern: Pinwheel, Number 230. Pattern repeat 1-3/4 inches (44.5 mm), open area 58 percent. Pattern: Shuriken, Number 231. Pattern repeat 2 inches (51.5 mm), open area 33 percent. Pattern: Bubbles, Number 232. Random opening pattern, open area varies. Pattern: Kauai, Number 233. Pattern repeat 2-3/4 inches (69.8 mm), open area 58 percent. Pattern: Pebbles, Number 234. Random opening pattern, open area varies. Pattern: Cubic, Number 235. Random opening pattern, open area varies. Pattern: Custom as indicated on the drawings. Thickness: ______. Material and Finish: Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Brass: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Stainless Steel: Satin Finish No. 4. Mirror Polish No.8 finish. Steel: Prime finish. Powder Coat Colors (As selected by Architect). ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. Fill in size if specified here. Coordinate with drawings or the attached grille schedule. Waterjet Cut Grille Size: __________ height by ___________ width. Waterjet Cut Grille Size: Heights and widths indicated on Drawings. Waterjet Cut Grille Size: Heights and widths indicated on Grille Schedule. Round Perforated Grilles: ** NOTE TO SPECIFIER ** Not all perforation patterns can be used on round grilles; consult manufacturer's product data for available patterns and sizes. Delete all but one of the following 28 paragraphs describing perforated sheet metal grille patterns; if more than one pattern or finish is required, indicate patterns and finish on the drawings or the attached grille schedule. Pattern: Square Link, Number 200. Pattern repeat 1 inch (25.5mm), open area 38 percent. Pattern repeat 1-1/4 inches (31.8 mm), open area 40 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 49 percent. Pattern repeat 2-1/4 inches (57.2 mm), open area 56 percent. Pattern: Parquet, Number 201. Pattern repeat 1-3/16 inches (30.2 mm), open area 35 percent. Pattern: Grecian, Number 202. Pattern repeat 1-1/4 inches (31.8 mm), open area 39 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 58 percent. Pattern: Honeycomb, Number 203. Pattern repeat 3/4 inch (19 mm), open area 50 percent. Pattern: Clover Leaf, Number 204. Pattern repeat 1/2 by 3/16 inch (12.5 by 4.8 mm), open area 51 percent. Pattern repeat 1/2 by 1/4 inch (12.5 by 6.5 mm), open area 52 percent. Pattern repeat 1 inch (25.5 mm), open area 50 percent. Pattern: Diamond, Number 205. Pattern repeat 1/4 inch (6.5 mm) with 1/4 inch (6.5 mm) bar, open area 25 percent. Pattern repeat 1/2 inch (12.5 mm) with 1/4 inch (6.5 mm) bar, open area 45 percent. Pattern repeat 3/4 inch (19 mm) with 1/4 inch (6.5 mm) bar, open area 56 percent. Pattern repeat 1 inch (25.5 mm) with 1/4 inch (6.5 mm) bar, open area 64 percent. Pattern: Maltese, Number 206. Pattern repeat 15/16 inch (23.8 mm), open area 38 percent. Pattern repeat 1-3/4 inches (44.45 mm), open area 45 percent. Pattern: Shell, Number 207. Pattern repeat 5/8 inch (15.9 mm), open area 48 percent. Pattern repeat 1-1/8 inches (28.5 mm), open area 56 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 72 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 84 percent. Pattern: Lattice, Number 208. Pattern repeat 1/4 inch (6.5 mm) with 1/4 inch (6.5 mm) bar, open area 25 percent. Pattern repeat 1/2 inch (12.7 mm) with 1/4 inch (6.5 mm) bar, open area 45 percent. Pattern repeat 3/4 inch (19 mm) with 1/4 inch (6.5 mm) bar, open area 56 percent. Pattern repeat 1 inch (25.5 mm) with 1/4 inch (6.5 mm) bar, open area 64 percent. Pattern: Half Shell, Number 209. Pattern repeat 1-5/16 inches (33.3 mm), open area 55 percent. Pattern repeat 1-3/4 inches (44.45 mm), open area 68 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 80 percent. Pattern: School Slot, Number 210. Pattern repeat 1/4 inch (6.5 mm) by 1 inch (25.5 mm), open area 35 percent. Pattern repeat 5/16 inch (7.9 mm) by 1-3/8 inch (35 mm), open area 43 percent. Pattern: Egyptian, Number 211. Pattern repeat 1 inch (25.5mm), open area 40 percent. Pattern repeat 2 inches (51 mm), open area 55 percent. Pattern: Straight Hole, Number 212. Pattern repeat 1/4 inch (6.5 mm) diameter with 1/2 inch (12.7 mm) centers, open area 21 percent. (other sizes available). Pattern: Staggered Hole, Number 213. Pattern repeat 1/4 inch (6.5 mm) diameter with 1/2 inch (12.7 mm) centers, open area 23 percent. (other sizes available). Pattern: Gothic, Number 214. Pattern repeat 1-1/16 inches (27 mm), open area 58 percent. Pattern: Brick, Number 215. Pattern repeat 1/4 inch (6.5 mm) by 1 inch (25.5 mm), open area 35 percent. Pattern repeat 3/8 inch (9.5 mm) by 1 inch (25.5 mm), open area 43 percent. Pattern: Square on Diamond, Number 216. Pattern repeat 1/2 inch (12.5 mm), open area 45 percent. Pattern repeat 3/4 inch (19 mm), open area 56 percent. Pattern repeat 1 inch (25.5 mm), open area 64 percent. Pattern: Triangle and Clover, Number 217. Pattern repeat 1-1/4 inches (31.8 mm), open area 23 percent. Pattern: Cross Link, Number 218. Pattern repeat 1-1/2 inches (38.1 mm), open area 45 percent. Pattern: Windsor, Number 219. Pattern repeat 1-9/16 inches (39.68 mm), open area 48 percent. Pattern repeat 2 inches (51 mm), open area 55 percent. Pattern: Classic, Number 220. Pattern repeat 1-5/8 inches (41.27mm) by 1-5/16 inches (33.75 mm), open area 58 percent. Pattern repeat 2 inches (51 mm) by 1-3/4 inches (44.5 mm), open area 72 percent. Pattern: Tear Drop, Number 221. Pattern repeat 1-3/4 inches (44.5 mm) by 1-9/16 inches (39.68 mm), open area 66 percent. Pattern: Circle Link, Number 222. Pattern repeat 2-1/2 inch (12.7 mm) round, open area 65 percent. Pattern: Mosaic, Number 223. Pattern repeat 1-1/32 inches (26.19 mm), open area 54 percent. Pattern: Imperial, Number 224. Pattern repeat 1-7/8 inches (47.6 mm), open area 47 percent. Pattern: Majestic, Number 225. Pattern repeat 1 inch (25.5 mm), open area 40 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 52 percent. Pattern repeat 2-1/4 inches (57.2 mm), open area 64 percent. Pattern: Cathedral, Number 226. Pattern repeat 2-1/4 inches (57.15 mm) by 2-3/16 inches (55.5 mm), open area 57 percent. Pattern: Petals, Number 227. Pattern repeat 1-7/8 inches (47.6 mm), open area 52 percent. Pattern: Weave 228. Pattern repeat 1/2 inches (12.5 mm) by 1/2 inches (12.5 mm), open area 45 percent. Pattern: Orient, Number 229. Pattern repeat 2 inches (51 mm), open area 48 percent. Pattern: Pinwheel, Number 230. Pattern repeat 1-3/4 inches (44.5 mm), open area 58 percent. Pattern: Shuriken, Number 231. Pattern repeat 2 inches (51.5 mm), open area 33 percent. Pattern: Bubbles, Number 232. Random opening pattern, open area varies. Pattern: Kauai, Number 233. Pattern repeat 2-3/4 inches (69.8 mm), open area 58 percent. Pattern: Pebbles, Number 234. Random opening pattern, open area varies. Pattern: Cubic, Number 235. Random opening pattern, open area varies. ** NOTE TO SPECIFIER ** Select the material and thickness required from the following paragraphs. Delete the paragraphs not required. Standard thicknesses are indicated however; all products are available in any thickness upon request. Material: ** NOTE TO SPECIFIER ** Aluminum is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Aluminum, __ inch thick. ** NOTE TO SPECIFIER ** Brass is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Brass, __ inch thick. ** NOTE TO SPECIFIER ** Bronze is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Bronze, __ inch thick. ** NOTE TO SPECIFIER ** Stainless Steel is available in a 1/16 inch minimum thickness and a 14 gauge maximum thickness. Select thickness required below. Stainless Steel, __ inch thick. ** NOTE TO SPECIFIER ** Steel is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Steel, __ inch thick. Construction: Form true circle to indicated radius; finish cut edge to match sheet finish. Form 3/4 inch (19 mm) by 1/8 inch (3.2 mm) thick bar of metal matching face sheet to true cylinder to indicated radius; weld ends together and finish weld smooth. Collar weld cylinder to concealed surface of face sheet concentric with face sheet; finish welds smooth. ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. Fill in size if specified here. Coordinate with drawings or the attached grille schedule. Round Perforated Sheet Metal Grille Size: __________ diameter. Round Perforated Sheet Metal Grille Size: Diameters indicated on Drawings. Round Perforated Sheet Metal Grille Size: Diameters indicated on the Grille Schedule. ** NOTE TO SPECIFIER ** Select finish required. If more than one finish is required indicated on the drawings or the attached grille schedule. Finish: Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Brass: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Stainless Steel: Satin Finish No. 4. Mirror Polish No.8 finish. Steel: Prime finish. Powder Coat Colors (As selected by Architect). Progressive Louvers: ** NOTE TO SPECIFIER ** Select the material and thickness required from the following paragraphs. Delete the paragraphs not required. Standard thicknesses are indicated however; all products are available in any thickness upon request. Material: ** NOTE TO SPECIFIER ** Aluminum is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Aluminum, __ inch thick. ** NOTE TO SPECIFIER ** Brass is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Brass, __ inch thick. ** NOTE TO SPECIFIER ** Bronze is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Bronze, __ inch thick. ** NOTE TO SPECIFIER ** Stainless Steel is available in a 1/16 inch minimum thickness and a 14 gauge maximum thickness. Select thickness required below. Stainless Steel, __ inch thick. ** NOTE TO SPECIFIER ** Steel is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Steel, __ inch thick. Construction: Form from single metal sheet; form louver vanes with radiused end returns. ** NOTE TO SPECIFIER ** Delete two of the three following paragraphs. Form louvers 1/2 inch (12.7 mm) height, 3/16 inch (4.7 mm) projection, at 3/4 inch (19 mm) vertical spacing. Form louvers 5/8 inch (15.9 mm) height, 1/4 inch (6.5 mm) projection, at 15/16 inch (23.8 mm) vertical spacing. Form louvers 3/4 inch (19 mm) height, 1/4 inch (6.5 mm) projection, at 1-1/8 inches (28.5 mm) vertical spacing. Provide for indicated anchoring devices. Finish sight-exposed edges to match sheet finish. ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. Fill in size if specified here. Coordinate with drawings or the attached grille schedule. Progressive Louver Size: __________ height by _________ width. Progressive Louver Size: Sizes indicated on drawings. Progressive Louver Size: Sizes indicated on Grille Schedule. ** NOTE TO SPECIFIER ** Select finish required. If more than one finish is required indicated on the drawings or the attached grille schedule. Finish: Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Brass: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Stainless Steel: Satin Finish No. 4. Mirror Polish No.8 finish. Steel: Prime finish. Powder Coat Colors (As selected by Architect). Radiator Grilles: ** NOTE TO SPECIFIER ** Delete all but one of the following 28 paragraphs describing perforated sheet metal grille patterns; if more than one pattern or finish is required, indicate patterns and finish on the drawings or the attached grille schedule. Pattern: Square Link, Number 200. Pattern repeat 1 inch (25.5mm), open area 38 percent. Pattern repeat 1-1/4 inches (31.8 mm), open area 40 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 49 percent. Pattern repeat 2-1/4 inches (57.2 mm), open area 56 percent. Pattern: Parquet, Number 201. Pattern repeat 1-3/16 inches (30.2 mm), open area 35 percent. Pattern: Grecian, Number 202. Pattern repeat 1-1/4 inches (31.8 mm), open area 39 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 58 percent. Pattern: Honeycomb, Number 203. Pattern repeat 3/4 inch (19 mm), open area 50 percent. Pattern: Clover Leaf, Number 204. Pattern repeat 1/2 by 3/16 inch (12.5 by 4.8 mm), open area 51 percent. Pattern repeat 1/2 by 1/4 inch (12.5 by 6.5 mm), open area 52 percent. Pattern repeat 1 inch (25.5 mm), open area 50 percent. Pattern: Diamond, Number 205. Pattern repeat 1/4 inch (6.5 mm) with 1/4 inch (6.5 mm) bar, open area 25 percent. Pattern repeat 1/2 inch (12.5 mm) with 1/4 inch (6.5 mm) bar, open area 45 percent. Pattern repeat 3/4 inch (19 mm) with 1/4 inch (6.5 mm) bar, open area 56 percent. Pattern repeat 1 inch (25.5 mm) with 1/4 inch (6.5 mm) bar, open area 64 percent. Pattern: Maltese, Number 206. Pattern repeat 15/16 inch (23.8 mm), open area 38 percent. Pattern repeat 1-3/4 inches (44.45 mm), open area 45 percent. Pattern: Shell, Number 207. Pattern repeat 5/8 inch (15.9 mm), open area 48 percent. Pattern repeat 1-1/8 inches (28.5 mm), open area 56 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 72 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 84 percent. Pattern: Lattice, Number 208. Pattern repeat 1/4 inch (6.5 mm) with 1/4 inch (6.5 mm) bar, open area 25 percent. Pattern repeat 1/2 inch (12.7 mm) with 1/4 inch (6.5 mm) bar, open area 45 percent. Pattern repeat 3/4 inch (19 mm) with 1/4 inch (6.5 mm) bar, open area 56 percent. Pattern repeat 1 inch (25.5 mm) with 1/4 inch (6.5 mm) bar, open area 64 percent. Pattern: Half Shell, Number 209. Pattern repeat 1-5/16 inches (33.3 mm), open area 55 percent. Pattern repeat 1-3/4 inches (44.45mm), open area 68 percent. Pattern repeat 2-1/2 inches (63.5 mm), open area 80 percent. Pattern: School Slot, Number 210. Pattern repeat 1/4 inch (6.5 mm) by 1 inch (25.5 mm), open area 35 percent. Pattern repeat 5/16 inch (7.9 mm) by 1-3/8 inch (35 mm), open area 43 percent. Pattern: Egyptian, Number 211. Pattern repeat 1 inch (25.5mm), open area 40 percent. Pattern repeat 2 inches (51 mm), open area 55 percent. Pattern: Straight Hole, Number 212. Pattern repeat 1/4 inch (6.5 mm) diameter with 1/2 inch (12.7 mm) centers, open area 21 percent. (other sizes available). Pattern: Staggered Hole, Number 213. Pattern repeat 1/4 inch (6.5 mm) diameter with 1/2 inch (12.7 mm) centers, open area 23 percent. (other sizes available). Pattern: Gothic, Number 214. Pattern repeat 1-1/16 inches (27 mm), open area 58 percent. Pattern: Brick, Number 215. Pattern repeat 1/4 inch (6.5 mm) by 1 inch (25.5 mm), open area 35 percent. Pattern repeat 3/8 inch (9.5 mm) by 1 inch (25.5 mm), open area 43 percent. Pattern: Square on Diamond, Number 216. Pattern repeat 1/2 inch (12.5 mm), open area 45 percent. Pattern repeat 3/4 inch (19 mm), open area 56 percent. Pattern repeat 1 inch (25.5 mm), open area 64 percent. Pattern: Triangle and Clover, Number 217. Pattern repeat 1-1/4 inches (31.8 mm), open area 23 percent. Pattern: Cross Link, Number 218. Pattern repeat 1-1/2 inches (38.1 mm), open area 45 percent. Pattern: Windsor, Number 219. Pattern repeat 1-9/16 inches (39.68 mm), open area 48 percent. Pattern repeat 2 inches (51 mm), open area 55 percent. Pattern: Classic, Number 220. Pattern repeat 1-5/8 inches (41.27mm) by 1-5/16 inches (33.75 mm), open area 58 percent. Pattern repeat 2 inches (51 mm) by 1-3/4 inches (44.5 mm), open area 72 percent. Pattern: Tear Drop, Number 221. Pattern repeat 1-3/4 inches (44.5 mm) by 1-9/16 inches (39.68 mm), open area 66 percent. Pattern: Circle Link, Number 222. Pattern repeat 2-1/2 inch (12.7 mm) round, open area 65 percent. Pattern: Mosaic, Number 223. Pattern repeat 1-1/32 inches (26.19 mm), open area 54 percent. Pattern: Imperial, Number 224. Pattern repeat 1-7/8 inches (47.6 mm), open area 47 percent. Pattern: Majestic, Number 225. Pattern repeat 1 inch (25.5 mm), open area 40 percent. Pattern repeat 1-3/4 inches (44.5 mm), open area 52 percent. Pattern repeat 2-1/4 inches (57.2 mm), open area 64 percent. Pattern: Cathedral, Number 226. Pattern repeat 2-1/4 inches (57.15 mm) by 2-3/16 inches (55.5 mm), open area 57 percent. Pattern: Petals, Number 227. Pattern repeat 1-7/8 inches (47.6 mm), open area 52 percent. Pattern: Weave 228. Pattern repeat 1/2 inches (12.5 mm) by 1/2 inches (12.5 mm), open area 45 percent. Pattern: Orient, Number 229. Pattern repeat 2 inches (51 mm), open area 48 percent. Pattern: Pinwheel, Number 230. Pattern repeat 1-3/4 inches (44.5 mm), open area 58 percent. Pattern: Shuriken, Number 231. Pattern repeat 2 inches (51.5 mm), open area 33 percent. Pattern: Bubbles, Number 232. Random opening pattern, open area varies. Pattern: Kauai, Number 233. Pattern repeat 2-3/4 inches (69.8 mm), open area 58 percent. Pattern: Pebbles, Number 234. Random opening pattern, open area varies. Pattern: Cubic, Number 235. Random opening pattern, open area varies. ** NOTE TO SPECIFIER ** Select the material and thickness required from the following paragraphs. Delete the paragraphs not required. Material: ** NOTE TO SPECIFIER ** Aluminum is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Aluminum, __ inch thick. ** NOTE TO SPECIFIER ** Brass is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Brass, __ inch thick. ** NOTE TO SPECIFIER ** Bronze is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Bronze, __ inch thick. ** NOTE TO SPECIFIER ** Stainless Steel is available in a 1/16 inch minimum thickness and a 14 gauge maximum thickness. Select thickness required below. Stainless Steel, __ inch thick. ** NOTE TO SPECIFIER ** Steel is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Steel, __ inch thick. Construction: Form straight edges to minimum radius allowed by metal thickness before grain separation of metal. Build in reinforcement for anchoring devices in accordance with approved shop drawings; weld to concealed surfaces of face sheets and edges. Form perforated patterns in face sheets and cut-outs in sides for radiator controls in accordance with approved shop drawings. Form top and bottom edges flush. Weld corners and metal intersections. Finish sight-exposed welded surfaces to match sheet finish. ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. Fill in size if specified here. Coordinate with drawings or the attached grille schedule. Radiator Grille Size: __________ height by _________ width. Radiator Grille Size: Sizes indicated on Drawings. Radiator Grille Size: Sizes indicated on the Grille Schedule. ** NOTE TO SPECIFIER ** Select finish required. If more than one finish is required indicated on the drawings or the attached grille schedule. Finish: Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Brass: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Stainless Steel: Satin Finish No. 4. Mirror Polish No.8 finish. Steel: Prime finish. Powder Coat Colors (As selected by Architect). Equipment Plates: ** NOTE TO SPECIFIER ** Fabricated to match Drawings or template provided by Architect.

** NOTE TO SPECIFIER ** Select the material and thickness required from the following paragraphs. Delete the paragraphs not required. Material: ** NOTE TO SPECIFIER ** Aluminum is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Aluminum, __ inch thick. ** NOTE TO SPECIFIER ** Brass is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Brass, __ inch thick. ** NOTE TO SPECIFIER ** Bronze is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Bronze, __ inch thick. ** NOTE TO SPECIFIER ** Stainless Steel is available in a 1/16 inch minimum thickness and a 14 gauge maximum thickness. Select thickness required below. Stainless Steel, __ inch thick. ** NOTE TO SPECIFIER ** Steel is available in a 1/16 inch minimum thickness and a 1/8 inch (3.2 mm) maximum thickness. Select thickness required below. Steel, __ inch thick. Construction: Form plates and provide penetrations in accordance with supplied templates. Build in reinforcement for anchoring devices in accordance with approved shop drawings; weld to concealed surfaces of face sheets and edges. Finish sight-exposed edges to match sheet finish. ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. Fill in size if specified here. Coordinate with drawings or the attached grille schedule. Equipment Plates Size: __________ height by _________ width. Equipment Plates Size: Sizes indicated on Drawings. Equipment Plates Size: Sizes indicated on the Grille Schedule. ** NOTE TO SPECIFIER ** Select finish required. If more than one finish is required indicated on the drawings or the attached grille schedule. Finish: Aluminum: Satin No. 4 finish. Mirror Polish No. 8 finish. Prime finish. Anodized finish: Black. Clear. Duranodic. Powder Coat Colors (As selected by Architect). Brass: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Bronze: Satin Finish No. 4. Mirror Polish No.8 finish. Statuary Bronze. Light. Medium. Dark. Stainless Steel: Satin Finish No. 4. Mirror Polish No.8 finish. Steel: Prime finish. Powder Coat Colors (As selected by Architect).