Novatech Group > CSI Specifications > Sliding Aluminum - Framed Glass Doors Specification

Download in other formats

Docx | Docx-Canadian | Doc | WP | Rtf | Text

SECTION 08 32 13

SLIDING ALUMINUM - FRAMED GLASS DOORS

** NOTE TO SPECIFIER ** Novatech Group; Patio Doors, Entry Doors and Insulated Glass.
This section is based on the products of Novatech Group, which is located at:
160 Murano
Sainte-Julie, QC, Canada J3E 0C6
Tel: 450-922-6106
Fax: 450-922-9633
Email: request info (marketing@groupenovatech.com)
Web: https://www.groupenovatech.com
[ Click Here ] for additional information.
The Novatech Group designs and manufactures architectural products for residential, commercial, and institutional markets. We are Canadian leaders in entry doors, door glass, patio doors, as well as glass products. Our development aims for excellence, automation, and innovation at all levels.

PART 1

GENERAL

1.1

SECTION INCLUDES

** NOTE TO SPECIFIER ** Delete items below not required for project.

Sliding aluminum - framed glass doors.:

1.2

RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

Section 06 10 00 - Rough Carpentry.

Section 08 15 73 - Sliding Plastic Doors.

Section 08 35 13.13 - Accordion Folding Doors.

1.3

REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

AAMA/WDMA/CSA 101/I.S.2/A440 - NAFS - North American Fenestration Standard/Specification for windows, doors, and skylights.

CSA A440S1 - Canadian Supplement to AAMA/WDMA/CSA 101/I.S.2/A440-17, North American Fenestration Standard/Specification for windows, doors, and skylights.

U.S. Department of Energy - Energy Star Windows Program.

National Resources Canada - Energy Star Windows Program.

1.4

SUBMITTALS

Submit under provisions of Section 01 30 00 - Administrative Requirements.

Product Data:

Manufacturer's data sheets on each product to be used.

Preparation instructions and recommendations.

Storage and handling requirements and recommendations.

Typical installation methods.

** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.

Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square representing actual product, color, and patterns.

Shop Drawings: Include elevations of each opening and details of materials, construction, and finish. Include relationship with adjacent construction.

1.5

QUALITY ASSURANCE

Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with a minimum five years documented experience.

Installer Qualifications: Company specializing in performing Work of this section with minimum two years documented experience with projects of similar scope and complexity.

Source Limitations: Provide each type of product from a single manufacturing source to ensure uniformity.

** NOTE TO SPECIFIER ** Include mock-up if the project size or quality warrant the expense. The following is one example of how a mock-up on might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project. Delete if not required.

Mock-Up: Construct a mock-up with actual materials in sufficient time for Architect's review and to not delay construction progress. Locate mock-up as acceptable to Architect and provide temporary foundations and support.

Intent of mock-up is to demonstrate quality of workmanship and visual appearance.

If mock-up is not acceptable, rebuild mock-up until satisfactory results are achieved.

Retain mock-up during construction as a standard for comparison with completed work.

Do not alter or remove mock-up until work is completed or removal is authorized.

1.6

PRE-INSTALLATION CONFERENCE

Convene a conference approximately two weeks before scheduled commencement of the Work. Attendees shall include Architect, Contractor and trades involved. Agenda shall include schedule, responsibilities, critical path items and approvals.

1.7

DELIVERY, STORAGE, AND HANDLING

Store and handle in strict compliance with manufacturer's written instructions and recommendations.

Protect from damage due to weather, excessive temperature, and construction operations.

1.8

PROJECT CONDITIONS

Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.9

SEQUENCING

Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

1.10

WARRANTY

Manufacturer's Warranty: Provide manufacturer's standard limited warranty.

PART 2

PRODUCTS

2.1

MANUFACTURERS

Acceptable Manufacturer: Novatech Group, which is located at:
160 Murano
Sainte-Julie, QC, Canada J3E 0C6
Tel: 450-922-6106
Fax: 450-922-9633
Email: request info (marketing@groupenovatech.com);Web: https://www.groupenovatech.com

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

Substitutions: Not permitted.

Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2

PERFORMANCE AND DESIGN REQUIREMENTS

Testing Performance Standards: Except as otherwise indicated, requirements for thermally-broken aluminum doors, terminology and standards of performance and fabrication workmanship are those specified and recommended in AAMA/WDMA/CSA101/I.S.2/ A440-17 (NAFS-17) and CSA A440S1-19

Air Infiltration Test: With the door closed and latched, the Air Leakage Resistance test was performed in accordance with Clause 9.3.2 in conjunction with ASTM E283-04, "Standard Test Method for Determining Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors under Specified Pressure Differences across the Specimen".

Air infiltration testing was performed using a test pressure of 1.57 psf (75 Pa) and/or 6.24 psf (300 Pa).

The air leakage rate was calculated and compared to the allowable air leakage.

Water Resistance Penetration Test: With the door closed and latched, a four-cycle Water Penetration Resistance test was performed in accordance with Clause 9.3.3 in conjunction with ASTM E547-00 "Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Cyclic Static Air Pressure Difference".

The test was performed using the specified pressure differential and a water spray rate of at least 5.0 gal / sq ft / hour (204 L / sq m / hour).

Each cycle consisted of five minutes with the pressure applied and one minute with the pressure released, during which the water spray was continuously applied.

Uniform Load Structural Test: Per A Uniform Load Structural test was conducted in accordance with Clause 9.3.4.3 and ASTM E330-02 "Standard Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference," Procedure A.

After a 10 second preload (50 percent of test load), followed by 1 minute with the pressure released, the sample was subjected to a Uniform Load Structural test using a specified test pressure for a time of 10 seconds.

The test was performed in the positive and negative directions.

After the test loads were released, the permanent deflections were recorded as well as the sliding door was inspected for failure or permanent deformation of any part of the sliding door system that would cause any operational malfunction.

Configuration: OX or XO. Door Size: Up to 95 x 94 inches (2413 x 2388 mm)

Door Details: Standard Interlock with standard 2-5/8 inch (67 mm) sill.

Performance Grade and Class: LG-PG40

Air Leakage: 0.06 cfm/sq ft (0.3 L/s.m^2).

Pass at 6.24 psf (300 Pa).

Water Penetration Resistance: 10.5 psf (510 Pa)

Design Pressure: +/- 40 psf (+/-1920 Pa)

Door Details: Internally-reinforced interlock stiles. Reinforced with ergonomic stiffener bar. Sill Height: 2-5/8 inch (67 mm).

Performance Grade and Class: LG-PG50

Air Leakage: 0.06 cfm/sq ft (0.3 L/s.m^2).

Pass at 6.24 psf (300 Pa).

Water Penetration Resistance: 10.5 psf (510 Pa).

Design Pressure: +/-50 psf (+/-2400 Pa).

Door Details: Externally-reinforced interlock stiles. Reinforced with ergonomic stiffener bar. Sill Height: 2-5/8 inch (67 mm).

Performance Grade and Class: LG-PG60 and CW-PG60

Air Leakage: 0.06 cfm/sq ft (0.3 L/s.m^2).

Pass at 6.24 psf (300 Pa).

Water Penetration Resistance: 10.5 psf (510 Pa).

Design Pressure: +/-60 psf (+/-2880 Pa).

Configuration: OX or XO. Door Size: Up to 122 x 96 inches (3099 x 2438 mm)

Door Details: Externally-reinforced interlock stiles. Reinforced with ergonomic stiffener bar. Sill Height: 2-5/8 inch (67 mm).

Performance Grade and Class: AW-PG40

Air Leakage: 0.25 cfm/sq ft (1.4 L/s.m^2).

Pass at 6.24 psf (300 Pa).

Water Penetration Resistance: 10 psf (480 Pa).

Design Pressure: +/-40 psf (+/-1920 Pa).

** NOTE TO SPECIFIER ** U-factor of the sliding door system was determined using the simulation procedure specified in NFRC 100 and the SHGC was determined using simulation procedures specified in NFRC 200. The simulation was conducted to NFRC 100 and NFRC 200 using specialized computer simulation software that was developed by the Lawrence Berkeley National Laboratory and is consistent with the ISO 15099 standard.

Energy Performance

Glass Package: Low-E 272 (4 mm) (S No. 2)