High-Strength Industrial Flooring

Color-Rok Flooring is an epoxy coating and colored silica quartz system used to decorate and protect most substrates including concrete, stone, wood, and metal. The Color-Rok Flooring system produces a seamless, slip-resistant surface while offering protection from abrasion and chemical attack. Use on any floor, walkway, or ramp where safety precautions against slippery conditions are important and sanitary cleaning is mandatory.

Color-Rok Flooring Exterior Top Coat is a one-component, crystal clear liquid coating specifically formulated as an exterior top coat for Color-Rok Flooring quartz aggregate decorative surfacing. Also excellent as a clear coating for exterior surfaces of concrete, terrazzo, brick or stone. Not recommended as a coating for exterior wood.

Diamite AGC is a water-based epoxy coating intended to protect a wide range of substrates from graffiti abuse.  Diamite AGC is resistant to spray paint, ink, crayons and harsh chemicals and may be applied to virtually any sound, clean and dry surface. Diamite AGC provides a smooth, attractive and easy-to-clean surface.

Diamite Brushkote is a solvent-based epoxy coating intended to protect a wide range of substrates from chemical and abrasion attack. It is immune to harsh chemicals including caustics and most acids. Diamite Brushkote is an excellent choice where a smooth, attractive and easy-to-clean surface is desired. 

Diamite Brushkote VOC is a water-based, high performance epoxy coating intended to protect a wide range of substrates from abrasion and chemical attack.  Diamite Brushkote VOC is totally VOC compliant, allowing application indoors without toxic odors and is an excellent choice where an  easy-to-clean and durable surface is desired.

Diamite CSC is a 100% solids, high performance epoxy compound intended for use as a chemical-resistant and containment coating to protect concrete, brick or block walls and floors. Diamite CSC is resistant to most acids, caustics, solvents and other harsh chemicals. Diamite CSC is applied to walls and floors of spill, splash and chemical leakage containment areas.

Diamite NEC is a 100% solids, high performance novolac epoxy compound intended for use as a chemical-resistant and containment coating to protect concrete, brick or block walls and floors. Diamite NEC is resistant to most acids, caustics, solvents and other harsh chemicals. Diamite NEC is applied to walls and floors of spill, splash and chemical leakage containment areas.

• Diamite Extreme is a 95% solids, high performance proprietary novolac epoxy compound intended for use as a chemical-resistant and containment coating to protect concrete, brick or block walls and floors. Diamite Extreme is resistant to most acids, caustics, solvents and other harsh chemicals. Diamite Extreme is applied to walls and floors of spill, splash and chemical leakage containment areas.

Lexite 100 is a single application, high build epoxy coating intended to protect horizontal surfaces against both abrasion and chemical attack. Lexite 100 may be applied to most substrates including concrete, brick, stone, wood, metal and other coatings that are firmly bonded to the base substrate.

Lexite Conductive Primer is a two-part epoxy coating system that exhibits excellent abrasion resistance as well as static dissipative properties. Lexite Conductive Primer is intended to be used in conjunction with Lexite Conductive Top Coat. Lexite Conductive Primer may be applied to concrete and metal substrates.

Lexite Conductive Top Coat is a high-build, static dissipative epoxy top coating intended to protect horizontal surfaces against both abrasion and chemical attack. Lexite Conductive Top Coat may be applied to concrete and metal substrates. It is important that this product be used in conjunction with Lexite Conductive Primer to achieve proper resistance performance.

Lexite PWC is a single application, high build epoxy coating approved for potable water contact intended to protect horizontal surfaces against both abrasion and chemical attack. Lexite PWC meets the specifications for extractions studies in accordance with CFR Title 21 polymeric and resinous coatings when extracted under distilled water, heptane and alcohol. Lexite PWC may be applied to most substrates including concrete, brick, stone, wood, metal and other coatings that are firmly bonded to the base substrate.

Lexite Glow is a single application, high build epoxy coating intended to "glow in the dark." Lexite Glow is designed to glow after activation by a light source allowing for safe evacuation of a building in total darkness. Lexite Glow may be applied to most substrates including concrete, brick, stone, wood, metal and other coatings that are firmly bonded to the base substrate.

Porselin is an epoxy enamel paint designed to coat virtually any sound vertical surface. Porselin drys to a brilliant high gloss finish, and may be used in both interior and exterior applications. Porselin protects coated surfaces from chemical attack, weathering and abrasion.

Diamite Primer is designed to be used as a primer for other Metalcrete epoxy and urethane flooring systems. Diamite Primer is available in both a water and solvent-based formulation. The water-based formulation should be used where VOC compliant materials are required or where good ventilation is not possible. Diamite Primer Conductive formulation is available for Lexite Conductive epoxy flooring applications.

Diamite Primer MVB is a two-component 100% solids epoxy primer designed to control vapor emission rates up to 20 pounds / 24 hours / 1,000 square feet. Diamite Primer MVB should be used as a primer for other Metalcrete epoxy and urethane flooring systems. Diamite Primer is available in both a water and solvent-based formulation. The water-based formulation should be used where there are issues associated with moisture in the concrete sub-base.

Diamite Oil Stop Primer is designed to be used over petroleum based oil contaminated surfaces prior to the application of other Metalcrete epoxy and urethane coating and flooring systems.

Diamite AC Epoxy Flooring is an epoxy system specifically formulated for resistance to acetic acid. It is also highly resistant to sulfuric, hydrochloric and other corrosive acids as well as most alkalis in concentrations normally found in contact with floor surfaces. Diamite AC Epoxy Flooring is used on any physically sound, clean and dry substrate including concrete, brick, terrazzo, marble, metal or wood. It may be used as a chemical-resistant grout for joints between quarry or ceramic tile when mixed with silica aggregate.

Diamite SL Epoxy Flooring is an epoxy system used to restore worn and eroded floors to their original condition and protect them from future deterioration.  Diamite SL Epoxy Flooring may be applied on any physically sound, clean, and dry substrate including concrete, brick, terrazzo, marble, metal or wood.  It may also be used to improve floor tolerances and reduce surface imperfections.  It is completely immune to the corrosive action of acids and alkalis in concentrations normally found in contact with floor surfaces.

Diamite TR Epoxy Flooring is an epoxy mortar system used to restore worn and eroded floors to their original condition and to protect from future deterioration. Diamite TR Epoxy Flooring may be applied on any physically sound, clean, and dry substrate including concrete, brick, terrazzo, marble, metal or wood.  It may be used as a chemical-resistant grout for joints between quarry or ceramic tile.  Diamite TR Epoxy Flooring is completely immune to the corrosive action of acids and alkalis in concentrations normally found in contact with floor surfaces.

Diamite Vinyl Ester is a vinyl ester resin combined with natural aggregate used to protect horizontal or vertical surfaces against abrasion and severe chemical attack.  Diamite Vinyl Ester may be used in both interior and exterior applications.

Diamite Epoxy Terrazzo is an epoxy based coating and colored chip system used to decorate and protect most substrates including concrete, stone, wood, metal and other coatings that are firmly bonded to the base substrate.  Diamite Epoxy Terrazzo systems provide a smooth, dense and durable surface with all the beauty of conventional cement terrazzo but at a fraction of the cost.

Diamite LT Mortar is an epoxy and natural aggregate system used to protect horizontal surfaces against abrasion and chemical attack in low temperature environments. It is usually applied to concrete floors in need of repair due to excessive wear and chemical attack.  Diamite LT Mortar may be applied when ambient and substrate temperatures are as low as 20°F (-7°C).

Metalpoxy Flooring is an epoxy and iron aggregate system used to protect horizontal surfaces against the most severe abrasion and impact. Metalpoxy Flooring is usually applied to concrete substrates in need of repair due to excessive wear, gouging and impact, and floor areas subjected to steel wheel traffic.

Metalpoxy SL Flooring is a self-leveling epoxy and metallic aggregate system used to protect horizontal surfaces against the most severe abrasion and impact.  Metalpoxy SL Flooring is usually applied to concrete substrates in need of repair due to excessive wear, gouging and impact, and floor areas subjected to steel wheel traffic.  It is completely immune to the corrosive action of acids and alkalis in concentrations normally found in contact with floor surfaces.

Metalpoxy Plus Flooring is an epoxy and non-oxidizing metallic aggregate system used to protect horizontal surfaces against the most severe abrasion and impact. Metalpoxy Plus Flooring is usually applied to concrete substrates in need of repair due to excessive wear, gouging and impact, and floor areas subjected to steel wheel traffic.

Diathane is a high performance urethane coating intended to provide protection against abrasion and harsh chemical attack.  Diathane may be used as a top or finish coat for all Metalcrete epoxy systems.  Diathane is an excellent choice where a dense, and easy-to clean surface is required.

Diathane Slurry is a four-component water based urethane cement slurry that has exceptional wear performance and resistance to heat. Diathane Slurry is intended for indoor applications subjected to heavy foot traffic and hand cart traffic. The Diathane Slurry flooring system produces a seamless, slip-resistant surface while offering protection from abrasion and chemical attack.

Diathane Mortar is a four-component water based urethane cement trowel down mortar that has exceptional wear performance and resistance to heat. Diathane Mortar is intended for indoor applications subjected to heavy foot traffic and hand cart traffic. The Diathane Mortar flooring system produces a seamless, slip-resistant surface while offering protection from abrasion and chemical attack.

Diathane Slurry TC is a four-component water based urethane top coat designed to be applied over Diathane Slurry. Diathane Slurry and Diathane Slurry TC have exceptional wear performance and resistance to heat. Diathane Slurry TC is intended for indoor applications subjected to heavy foot traffic and hand cart traffic. The Diathane Slurry TC flooring system produces a seamless, slip-resistant surface while offering protection from abrasion and chemical attack.

Diathane AGC is a VOC compliant urethane coating intended to protect a wide range of substrates from graffiti abuse.  Diathane AGC is resistant to spray paint, ink, crayons and harsh chemicals and may be applied to virtually any sound, clean and dry surface. Diathane AGC provides a smooth, attractive and easy-to-clean surface.

Diathane LT Mortar is a urethane and natural aggregate system used to protect horizontal surfaces against abrasion and chemical attack in low temperature environments. It is usually applied to concrete floors in need of repair due to excessive wear and chemical attack. Diathane LT Mortar may be applied when ambient and substrate temperatures are as low as 10°F (-12°C).

Diamite TDC is a polyurethane system used as a traffic deck coating system to protect concrete from future deterioration due to moisture infiltration and chloride ion attack as well as abrasion.  The Diamite TDC system consists of a primer, base coat, intermediate coat (optional) and top coat.  Diamite TDC is an elastomer designed to be a waterproofing membrane.  Diamite TDC may be applied on any physically sound, clean and dry substrate including concrete, brick, terrazzo,  marble, metal or wood.  It is completely immune to the corrosive action of salts, acids and alkalis in concentrations normally found in contact with concrete surfaces subjected to vehicular or pedestrian traffic.

Metco Hi-Mod Epoxy is a two-component, 100% solids, moisture insensitive, high modulus epoxy bonding agent formulated to bond fresh concrete to old concrete and old concrete to old concrete.  It is designed to meet the requirements of ASTM C 881 specifications.  Metco Hi-Mod Epoxy may also be used as a primer on damp and porous concrete surfaces.  It is available in three consistencies; low viscosity, medium viscosity and gel.

Metco Low-Mod Epoxy is a two-component, 100% solids, moisture insensitive, low modulus epoxy bonding agent formulated to bond fresh concrete to old concrete and old concrete to old concrete. Metco Low-Mod Epoxy should be used where large temperature variations are possible, and is designed to meet the requirements of ASTM C 881 specifications. Metco Low-Mod Epoxy may also be used as a primer on damp and porous concrete surfaces.  It is available in three consistencies; low viscosity, medium viscosity and gel. 

Metco LPL Epoxy is a two-component, long pot life, 100% solids, moisture insensitive, high modulus epoxy bonding agent formulated to provide extended working  time.  Metco LPL Epoxy is used to bond fresh concrete to hardened concrete and old concrete to old concrete, and is designed to meet the requirements of ASTM C 881 specification, Types I, II & V, Grade 2 (medium viscosity).  Metco LPL Epoxy is used in hot weather applications or where long open times are required.

Metco VLT Epoxy is a very low temperature, rapid setting, two-component, 100% solids, moisture  insensitive,  high modulus epoxy bonding agent formulated to bond steel and other ferrous materials to old concrete and old concrete to old concrete.  It is designed to meet the requirements of ASTM C 881 specifications. Also available in polyurethane formulation.

Acrylpave is a water-based, VOC compliant latex designed  to be added  to portland cement based systems of all types to enhance hardened properties.  Through internal reinforcement of the cementitious system, greater bond, flexural, and tensile strengths can be achieved.  Acrylpave internally reinforces the cement matrix, thereby giving the system a two way strength mechanism.  In addition, Acrylpave can dramatically improve freeze / thaw, scaling, and salt resistance and damp-proofs against water ingress.

Herculox is a milky white re-emulsifiable liquid adhesive used to bond new concrete toppings or cement plaster to floors, walls, walkways, steps, loading docks, ramps or any structurally sound masonry without chipping, scarifying or otherwise roughening the surface.  Herculox also rejoins broken masonry or other materials with a tenacious bond.

Metcobond is a styrene butadiene latex additive designed to increase bond, flexural and tensile strengths in cement-based mortars and concrete.  Metcobond also increases chemical resistance and reduces permeability of conventional concrete. Metcobond is used as an admixture in thin-set mortars, stucco, tile grout, terrazzo, plaster, slurries, bond coats and concrete overlays and toppings.

Thinpave is a latex modified concrete repair mortar for patching or resurfacing horizontal surfaces. It is used as a trowel-down material and is suitable  for both indoor and outdoor applications. Thinpave can be used from featheredge to 1/2 inch (12.7 mm) thicknesses.

Thinpave C1 is a latex modified concrete repair mortar for patching or resurfacing horizontal surfaces. It is used as a trowel-down material and is suitable for both indoor and outdoor applications. Thinpave C1 can be used from featheredge to  1/2 inch (12.7 mm) thicknesses.

Thickpave is a latex modified concrete repair mortar for patching or resurfacing horizontal surfaces. It is used as a trowel-down or screedable material and is suitable for both indoor and outdoor applications.  Thickpave can be used from a thickness of 1/2 inch (12.7 mm) to 2 inches (50 mm).

Vertipave is a latex-modified concrete repair mortar for vertical and overhead repairs.  It is designed at  a packable, trowel  grade consistency along with special additives that prevent sagging and slumping.  Vertipave is ideal for hard-to-form repairs both inside and outside and can be used from featheredge to a 4 inch (102 mm) thickness.

Vertipave C1 is a one-component vinyl fortified concrete repair mortar for vertical and overhead repairs.  It is designed at a packable, trowel grade consistency along with special additives that prevent sagging and slumping.  Vertipave C1 is ideal for hard-to-form repairs both inside and outside and can be used from featheredge to a 4 inch (102 mm) thickness.

Flexpave is a flexible, fiber reinforced, latex modified concrete repair mortar for patching or resurfacing both horizontal and vertical surfaces.  It is used as a trowel-applied material and is suitable for both indoor and outdoor applications.  Flexpave can be used from featheredge to 1/4 inch (6 mm) thicknesses.

Flowpave is a one-part, latex-modified compound designed to be installed at a self-leveling consistency.  It is mixed only with water and can be pumped or poured into place.  Flowpave can be used over concrete, wood, or mastic adhesives.  It provides a smooth, level underlayment for tile, carpet, or resilient floor coverings.

Flowpave Supreme is a self-leveling floor surfacing material designed for use as an underlayment or as a wearing surface for light duty traffic.  It is particularly useful where floors are out of tolerance or the surface has deteriorated or been damaged.  When mixed with water, Flowpave Supreme can be applied to small or large  areas at thicknesses from 1/16 inch (1.6 mm) to 1 inch (25.4 mm).

Metcrete is a concrete repair mortar for patching or resurfacing horizontal surfaces.  It is used as a trowel-down or screedable material and is suitable for both indoor and outdoor applications.  Metcrete can be used from a thickness of 1/2 inch (12.7 mm) to 6 inches (152 mm).

Plug-It is a rapid setting hydraulic cement mortar designed for filling holes and cracks in concrete or masonry.  When mixed with water, it sets in 2 to 4 minutes to allow rapid sealing and blockage of running water.  The early expansion which occurs as Plug-It sets assures a firm interlock to holes and cracks.

Speedpave MP is a rapid setting, high-early, magnesium phosphate based patching mortar for repair of concrete slabs and pavements.  It is a one-part system requiring only the addition of water for mixing.  Speedpave MP is designed for thicknesses from 1/2 inch (12.7 m) to 6 inches (152 mm).  It is good for both indoor and outdoor use.

Speedpave is a rapid setting, high-early, latex-modified patching mortar for repair of concrete slabs and pavements.  It is a one-part system requiring only the addition of water for mixing. Speedpave is designed for thicknesses from 1/2 inch (12.7 m) to 6 inches (152 mm).  It is good for both indoor and outdoor use.

Metcrete HT is a concrete topping and repair mortar for resurfacing or patching horizontal surfaces subject to high temperatures.  It is used as a trowel-down or screedable material and is suitable for both indoor and outdoor applications.  Metcrete HT can be used from a thickness of 1 inch (25.4 mm) to 6 inches (152 mm).  Provides good wear and impact resistance in combination with service temperatures up to 2000°F (1093°C). 

Finishpave is a one-part, latex modified repair compound designed for very thin trowel-on vertical applications.  Finishpave fills voids and smooths all surfaces to  provide a decorative and textured finish. When mixed with water, it gives a very workable consistency that can be applied to a near zero thickness.  It may also be applied as a slurry coat to provide a uniform colored appearance.

Featherpave is a one-part, latex modified repair compound designed for very thin trowel-on applications.  When mixed with water, it gives a very workable consistency that can be applied to a near zero thickness.  Featherpave is excellent for bringing localized bird baths and low spots up to proper level for subsequent floor covering.

Floor Quartz is a silica quartz aggregate dry shake intended for use as a surface hardener on fresh concrete to provide substantially greater wear  resistance on the surface of industrial grade floor slabs and pavements. It is applied to the surface of fresh concrete during the normal floor finishing operations with standard finishing equipment.

Floor TR Hardener is a trap rock aggregate dry shake intended for use as a surface hardener on fresh concrete to provide substantially greater wear resistance on the surface of industrial grade floor slabs and pavements. It is applied to the surface of fresh concrete during the normal floor finishing operations with standard finishing equipment.

Floor E Hardener is an emery aggregate dry shake intended for use as a surface hardener on fresh concrete to provide substantially greater wear resistance on the surface of industrial grade floor slabs and pavements. It is applied to the surface of fresh concrete during the normal floor finishing operations with standard finishing equipment.

Floor Quartz FF is a silica quartz aggregate dry shake intended for use as a surface hardener on fresh concrete to provide substantially greater wear resistance on the surface of industrial grade floor slabs and pavements. It is applied to the surface of fresh concrete after screeding and highway straightedge operations where a FF 50 or greater floor tolerance is specified.

Florundum is a marble aggregate dry shake intended for use as a surface hardener on fresh concrete to provide a decorative and durable floor surface in retail, commercial, institutional and residential grade facilities. It is applied on the surface of freshly placed concrete during normal floor finishing operations with standard finishing  equipment. Florundum will provide a terrazzo like appearance after it is diamond abraded and polished using the Retroplate system.

Metalplate is a metallic aggregate dry shake intended for use as a surface hardener on fresh concrete to provide substantially greater wear resistance on the surface of industrial grade floor slabs. It is applied to the surface of fresh concrete during the normal finishing operations on the floor with standard finishing equipment.

Metalplate Plus is a non-oxidizing metallic aggregate dry shake intended for use as a surface hardener on fresh concrete to provide substantially greater wear resistance on the surface of industrial grade floor slabs in combination with 100% resistance to oxidation or rusting. It is applied to the surface of fresh concrete during the normal finishing operations on the floor with standard finishing equipment.

Metalplate SD is metallic aggregate dry shake intended for use as a surface hardener on fresh concrete to provide substantially greater wear resistance on the surface of industrial grade floor slabs in combination with static disseminating, conductive, and spark resistant properties. It is applied to the surface of fresh concrete during the normal finishing operations on the floor with standard finishing equipment. 

Metalplate Supreme is high-metallic aggregate content dry shake intended for use as a heavy-duty surface hardener on fresh concrete to provide substantially greater wear resistance to the surface of industrial grade floor slabs. It is applied to the surface of fresh concrete during the normal finishing operations on the floor with standard finishing equipment.

Metalplate FF is a metallic aggregate dry shake intended for use as a surface hardener on fresh concrete to provide substantially greater wear resistance on the surface of industrial grade floor slabs where flatness tolerances are required.  It is applied to the surface of fresh concrete after screeding and highway straightedge operations where a FF 50 or greater floor tolerance is specified.

Metalcrete is a screedable, high strength metallic topping intended for use where heavy impact and abrasion are primary floor service conditions. This product is usually applied as a bonded topping over properly prepared existing concrete at a 2 inch (50.8 mm) thickness. Metalcrete can be placed up to 5 inches (127 mm) thick.

Met-Top E is a screedable, high strength emery aggregate based topping intended for use where heavy impact, gouging and abrasion are primary floor service conditions. This product is usually applied as a bonded topping over properly prepared existing concrete at a 2 inch (50.8 mm) thickness. Met- Top E can be placed up to 6 inches (152.4 mm) thick.

Metalpoxy Flooring is an epoxy and iron aggregate system used to protect horizontal surfaces against the most severe abrasion and impact. Metalpoxy Flooring is usually applied to concrete substrates in need of repair due to excessive wear, gouging and impact, and floor areas subjected to steel wheel traffic.

Metalcrete SC is a high-strength metallic aggregate shotcrete mortar that uses a proprietary chemical blend to acheive exceptionally high early and ultimate strengths. After 56 days, Metalcrete SC has strengths over 13,000 psi (96.5 MPa). Metalcrete SC is applied by using shotcrete equipment thickness ranging from 6" in overhead applications to 9" in vertical applications. Development of decline pathways going underground is critical for movement of machinery, material, and personnel - Metalcrete SC provides a superior wear surface that resists impact and abrasion.

Metalcrete HT is a metallic aggregate topping designed for use under high temperature exposure.  It can be applied from 1 inch (25.4 mm) to 4 inches (102 mm) in thickness and provides excellent wear and impact resistance in combination with service temperatures up to 2000°F (1093°C).

Metalcrete Plus is a screedable, high-strength metallic and natural aggregate topping intended for use where heavy impact, gouging and abrasion are primary floor service conditions. It is applied monolithically over fresh concrete or as a delayed two course bonded topping at a 1 inch (25.4 mm) to 4 inch (102 mm) thickness.

Metalcrete SF is a screedable, high-strength, steel fiber reinforced metallic topping intended for use where gouging, heavy impact and abrasion are primary floor service conditions. It is applied monolithically over fresh concrete or as a delayed two course bonded topping at a 1 inch (25.4 mm) to 4 inch (102 mm) thickness. 

Metalcrete Rapid is a rapid-setting, high early strength, metallic aggregate patching mortar for repair of concrete slabs and pavements.  It is a one-part system requiring only the addition of water for mixing. Metalcrete Rapid is designed for thicknesses from 1/2 inch (12.7 mm) to 3 inches (76 mm). Metalcrete Rapid is intended for floor repairs subjected to severe abrasion and impact. High early strengths allows for traffic and abuse within 1-2 hours.

Magnarok Grout is a non-shrink, non-metallic grout designed for use under steel baseplates of all types to provide precision support and bearing capacity.  It is formulated to be used from a plastic to a fluid, self-leveling consistency to assure complete filling of voids and spaces under plates, in shear keys, and around anchor bolts.  Compressive strengths are significantly higher than plain concrete.

Magnarok Metallic Grout is a non-shrink, metallic grout designed for use under heavy-duty steel base plates of all types to provide precision support  and bearing capacity. The metallic aggregate base of the material provides impact resistance and toughness not achievable with non-metallic grouts.  This grout can be used from a plastic to fluid self-leveling consistency to assure complete filling of voids and spaces under plates, in shear keys, and around anchor bolts.  Compressive strengths are significantly higher than plain concrete.

MagnaPak Grout is a non-shrink, non-metallic grout designed for use under steel base plates of all types, and grouting of hard to form precast panels, joints, and connections. It is formulated to be mixed to a damp, “dry-pack" consistency for no slump, no flow installation.  Compressive strengths are significantly higher than plain concrete.

MagnaPak Metallic Grout is a non-shrink, metallic aggregate grout designed for use under steel baseplates of all types, and grouting of hard to form precast panels, joints, and connections.  It is formulated to be mixed to a damp, “dry-pack" consistency for no slump, no flow installation. Compressive strengths are significantly higher than plain concrete.

Wedjrok Grout is a rapid setting, high early strength grout compound for use under steel baseplates of all types.  It is formulated at a pourable consistency and is free-flowing under baseplates and into anchor bolt sleeves.

Wedjrok FS Dry Pack Grout is a non-shrink, non-metallic grout designed for use under steel baseplates of all types, and grouting of hard to form precast panels, joints, and connections. It is formulated to be mixed to a damp, “dry-pack" consistency for no slump, no flow installation. Setting time is 15 to 20 minutes. Compressive strengths are significantly higher than plain concrete.

Magnarok LT Grout is a non-shrink, low temperature grout designed for use under steel baseplates of all types and as an anchoring compound. It is formulated to be used from a plastic to a fluid, self-leveling consistency to assure complete filling of voids and spaces under plates, in shear keys, and around anchor bolts.  This grout is specially designed for cold weather applications down to 20°F (-7°C).

Magnarok LTM Grout is a non-shrink, low temperature, metallic aggregate grout designed for use under steel baseplates of all types and as an anchoring  compound. The metallic aggregate base of the material provides impact resistance and toughness not achievable with non-metallic grouts. It is formulated to be used from a plastic to a fluid, self-leveling consistency to assure complete filling of voids and spaces under plates, in shear keys, and around anchor bolts. This grout is specially designed for cold weather applications down to 20°F (-7°C).

Magnarok HT Grout is a non-shrink, high temperature grout designed for use under steel baseplates of all types where temperatures in service will be up to 2000°F (1093°C).  It is formulated to be used from a plastic to a fluid, self-leveling consistency to assure complete filling of voids and spaces under plates, in shear keys, and around anchor bolts. Compressive strengths are significantly higher than plain concrete.

Magnarok Cable Sealing Cement provides an extremely dense, high-strength filler that seals all openings around electrical cables and positively prevents the transmission of flames, smoke and/or water through deck or bulkhead penetrations in marine applications.  It is a United States Coast Guard "accepted" cable sealing product for through-penetration fire stop designs. Magnarok Cable Sealing Cement is supplied as a dry powder that when mixed with water achieves high early strengths, slight expansion and long term non-shrink properties.

Diamite Epoxy Grout is a 100% reactive epoxy system designed to give very high strength, exceptional bond, chemical resistance, and tremendous toughness under load.  It contains a proprietary aggregate blend that maximizes yield while minimizing thermal movement and creep.  Diamite Epoxy Grout is dimensionally stable after hardening and is easily placed at a flowable consistency.

Diamite DP Epoxy Grout is a 100% reactive epoxy grout formulated for deep placements. This low exothermic epoxy grout achieves exceptionally high ultimate strengths, has a long pot life, and is resistant to creep when grouting machinery and equipment. Diamite DP Epoxy Grout is dimensionally stable after hardening, is chemical resistant, and expands to fill minor gaps and voids.

Diamite Novolac Epoxy Grout is a three component novolac epoxy grout system designed to provide excellent chemical resistance, very high strength, exceptional bond, and tremendous toughness under load.  It contains a proprietary aggregate blend that maximizes yield while minimizing thermal movement and creep.  Diamite Novolac Epoxy Grout is dimensionally stable after hardening and is easily placed at a flowable consistency. This product is recommended for applications where spills and splashes of acids, chemicals, solvents, and alkalines occur.

Diamite Fast-Set Grout is a fast setting, high early strength epoxy grout designed to take loads in 3 hours at normal ambient temperatures.  It provides excellent early and ultimate strengths and is resistant to common chemicals and fluids.  Diamite Fast-Set Grout is formulated with an optimum aggregate loading to balance placing requirements with desirable hardened properties.

Instarok Cement is a dry cement powder which when mixed with water hardens rapidly to a permanent, solid mass that is not affected by moisture, rain or submersion in water.  With nearly three times the strength of concrete, Instarok Cement anchors, patches and repairs in one hour or less.

Wedjrok Cement is a dry cement compound which when mixed with water hardens rapidly to a permanent, solid mass.  Wedjrok Cement is designed for applications in dry areas.  It sets firm within 15 minutes and is stronger than concrete in 1 hour.  Final strength is twice that of conventional concrete.

Diamite Anchoring Grout is a fast-setting epoxy grout designed to provide tremendous anchoring power in a short period of time for anchor bolts, embedments and dowels. Formulated to be pourable, it flows easily around bolts and into tough to access cavities.  Shutdown times or stressing in as little as 3 hours is achievable.

Seal N Kure  is an acrylic-based liquid designed to be applied as a thin membrane over new, green concrete to provide proper curing.  Because it holds in the proper amount of moisture, concrete will achieve its utmost potential in terms of strength, wear resistance, durability, and water tightness.  Seal N Kure forms a glossy film that is resistant to ultraviolet discoloring.

Seal N Kure 0800 is an acrylic-based liquid designed to be applied as a thin membrane over new, green concrete to provide proper curing. Because it holds in the proper amount of moisture, concrete will achieve its utmost potential in terms of strength, wear resistance, durability, and water tightness.  Seal N Kure 0800 forms a clear, glossy film that is resistant to ultraviolet discoloring.

Seal N Kure 30 is a high solids, acrylic liquid designed to give heavy-duty protection and proper curing to green concrete.  It acts as an efficient moisture barrier to allow concrete to develop its highest strength potential during the curing process. Seal N Kure 30 provides a hard film for excellent sealing properties on both new and old concrete.

Seal N Kure 30 CR is a high solids, chlorinated rubber liquid designed to give heavy-duty protection and proper curing to green concrete.  It is available in both clear and pigmented formulations. Seal N Kure 30 acts as an efficient moisture barrier to allow concrete to develop its highest strength potential during the curing process.  Seal N Kure 30 CR provides a hard film for excellent sealing properties on both new and old concrete.

Seal N Kure FDR  is an acrylic-based liquid designed to be applied as a thin membrane over new, green concrete to provide proper curing.  The Seal N Kure FDR membrane will chemically react and begin to lose bond with the base concrete after a two to four week period. Because it holds in the proper amount of moisture, concrete will achieve its utmost potential in terms of strength, wear resistance, durability, and water tightness.

Pavecure Crystal is a guaranteed non-yellowing, acrylic-based liquid designed to be applied as a thin membrane over new, green concrete to provide proper curing.  Because it holds in the proper amount of moisture, concrete will achieve its utmost potential in terms of strength, wear resistance, durability, and water tightness. Pavecure Crystal forms a clear, glossy film that is totally resistant to ultraviolet discoloring.

Metcure is a water-based, VOC compliant acrylic designed for use as a curing and sealing compound over new and old concrete. It is safe to use and produces a continuous film which keeps moisture in green concrete for proper curing.  Through proper concrete hydration,  Metcure brings concrete to its fullest potential in terms of strength, durability and wear resistance.  Better application is encouraged through user friendliness.

Metcure 0800 is a water-based, VOC compliant acrylic designed for use as a curing and sealing compound over new and old concrete. It is safe  to use and produces a continuous film which keeps moisture in green concrete for proper curing. Through proper concrete hydration, Metcure 0800 brings concrete to its fullest potential in terms of strength, durability and wear resistance. Better application is encouraged through user friendliness.

Metcure 30 is a high solids, water-based acrylic designed to give optimum curing and protection to green concrete of all types. When applied to new, green concrete, it gives an efficient moisture barrier  even at  high coverage rates that promotes proper concrete hydration.  Metcure 30 allows concrete to develop its utmost potential in terms of strength gain, durability, water tightness, and wear resistance. Because Metcure 30 is VOC compliant, it is safe to use and invites more effective workmanship.

Duralon is a water-based, VOC compliant sealer designed for use over concrete, stone and cement  based  terrazzo.    When applied  to properly cleaned concrete, it bonds tenaciously and forms a continuous, impermeable film.  Because the product is a water-based formulation, it is safe to use and can be applied in existing facilities without the operation problems associated with solvent-based sealers.  Duralon is excellent for sealing floors of all types but may also be used on walls, columns or exterior concrete.

Decksaver W is an acrylic-based sealer designed to penetrate and coat wooden structures and decks of all types. Its excellent penetrating properties make wood  virtually impermeable to water and helps protect from the harmful effects of dry rot, weathering and insect attack. Decksaver W is easy to use and dries quickly.

Diaseal is a thin-mil epoxy floor sealer designed to protect floors from penetration by numerous liquids and to resist mild chemical attack.  Because Diaseal is a one component material, it is easy to apply with standard equipment.  Diaseal adheres tenaciously to concrete and forms a continuous film for easier floor clean up and maintenance.

Parktop is an asphalt pavement sealer designed to prolong the serviceable life of the pavement.  Parktop protects against penetration by water, ultraviolet light, salt and mild chemical attack.  Parktop forms a smooth, hard, non-porous surface that is resistant to abrasion.

Decksaver C is a siloxane based penetrating sealer designed to protect concrete from the adverse effects of salt and water penetration.  By impregnating  the upper  surface of the concrete, it reacts chemically within the pore structure of the cement matrix to form a blocking crystal that virtually waterproofs the concrete.  Decksaver C is intended for use primarily on textured concrete subject to freeze/thaw cycling and de-icing salt attack.  Decksaver C is available in both 10% and 20% solids.

Decksaver C-VOC is a VOC Compliant silane/siloxane based penetrating sealer designed to protect concrete from the adverse effects of salt and water penetration.  By impregnating the upper surface of the concrete, it reacts chemically within the pore structure of the cement matrix to form a blocking crystal that virtually waterproofs the concrete.  Decksaver C-VOC is intended for use primarily on textured concrete subject to freeze/thaw cycling and de-icing salt attack. Decksaver C-VOC is available in both 10% and 20% solids.

Siliseal is a sodium-silicate based hardening and sealing  liquid designed  to promote enhanced surface strength of concrete.  It penetrates into concrete surfaces to form hardened crystals within the surface. Siliseal also develops a densified surface that gives a slight glossy appearance. Siliseal can be used as an alternative for curing compounds when  curing membranes are not permissible due to subsequent floor coverings.

Repel is a silane based penetrating sealer designed to protect concrete from the adverse effects of salt and water penetration. By impregnating the upper surface of the concrete, it reacts chemically within the pore structure of the cement matrix to form a blocking crystal that virtually waterproofs the concrete. Repel is intended for use primarily on textured concrete subject to freeze/thaw cycling and de-icing salt attack. Repel is available in both 20% and 40% solid.

Floorsaver is a water-based, magnesium silico-fluoride penetrant designed to harden and dust-proof concrete floor surfaces. Through a chemical reaction with the concrete, Floorsaver significantly increases the floor surface quality and ties up any loose dust.  This hardening process helps prevent further deterioration of the surface.

Floorsaver Supreme is a two-part, penetrating epoxy system designed to fill the capillaries and pore structure of concrete slabs. Through a chemical reaction and gluing together of the cement matrix, Floorsaver Supreme can overcome the effect of a soft, dusting surface as well as provide a barrier to water, salts,  mild acids,  and hydraulic  fluids.  Floorsaver Supreme improves the wear resistance of dusting floors and weak pavements.

Jointfill 302 is a two-component epoxy joint filler designed to be used in control and construction joints in concrete industrial floors.  Jointfill 302 is a low modulus, flexible joint filler used in saw cut floor joints to provide support and load-bearing capacity at the joint edges.  Jointfill 302 is used in floor control joints where slight movement is possible due to thermal variations.  It is available in two consistencies, self-leveling and gel, for horizontal and vertical applications.

Flexfill is a two-component epoxy joint filler designed to be used in control and construction joints in concrete industrial floors.  Flexfill is a low modulus, highly flexible joint filler used in saw cut floor joints to provide support and load-bearing capacity at the joint edges.  Flexfill is used in floor control joints where movement is possible due to thermal variations, shrinkage and deflection.  It is available in two consistencies, self-leveling and gel.  Flexfill is used in horizontal and vertical applications.

Crackbond is a very low viscosity two-component epoxy, joint and crack filler designed to penetrate and re-bond cracks in concrete.  This free flowing liquid is installed by simply allowing the material to penetrate the crack by gravity feed.  Crackbond may also be installed by pressure injection methods. It permanently bonds non-moving cracks and joints in concrete.

Diamite Non-Sag Crack Filler is a two-component, fast-setting epoxy gel packaged in special two-part caulk tubes.  It is mixed automatically as it is extruded from the tubes with a special caulk gun supplied with the material.  This low modulus system helps prevent future cracking.  It will not run through cracks and stays flush with surface.  There is no mess or waste since material is mixed only as needed.  This product works very well for filling cracks in floors prior to applying coatings and toppings.  Material can be coated over within hours.

Crackfill is a single component latex, very low viscosity joint and crack filler designed to penetrate and seal cracks in concrete.  Crackfill is installed by simply allowing the material to penetrate the crack by gravity feed, but may also be installed by pressure injection methods. Crackfill permanently seals moving and non-moving cracks and joints in concrete.

Crackfill AB is a single-component, low viscosity, rubberized pourable joint and crack filler designed to penetrate and seal cracks in asphalt and concrete.  Crackfill AB is installed by simply allowing the material to penetrate the crack by gravity feed. Crackfill AB permanently seals moving and non-moving cracks and joints.

Vulcanox I is a one-part, elastomeric, urethane, joint sealant used to seal and caulk both moving and non-moving joints and cracks.  It is used in both interior and exterior applications.  Vulcanox I is used to seal around windows and door frames, as well as joints in concrete, masonry and flashing.  It may be applied to wood, concrete, masonry, metal, stone and firmly bonded painted surfaces.

Vulcanox II is a two-part, catalyzed, elastomeric, urethane joint sealant used to seal and caulk both moving and non-moving joints and cracks. Vulcanox II is used in both interior and exterior applications when a rapid cure sealant is required.  Vulcanox II is used as a concrete joint filler for expansion joints or control joints.  It can also be used to seal around windows and door frames and to seal joints in masonry and flashing. It may be applied to wood, concrete, masonry, metal, stone and firmly bonded painted surfaces.

Acrylpave is a water-based, VOC compliant latex designed  to be added  to portland cement based systems of all types to enhance hardened properties.  Through internal reinforcement of the cementitious system, greater bond, flexural, and tensile strengths can be achieved.  Acrylpave internally reinforces the cement matrix, thereby giving the system a two way strength mechanism.  In addition, Acrylpave can dramatically improve freeze / thaw, scaling, and salt resistance and damp-proofs against water ingress.

Accel-Set is a non-chloride and noncorrosive based liquid admixture formulated to accelerate the set of concrete in cold weather. Accel-Set is added to portland cement concrete at the ready-mix plant or job site.  Accel-Set also improves workability while increasing early age strengths of concrete.

Superslump is a liquid admixture for concrete and mortar that allows water reduction without sacrificing slump or workability.  Through a chemical process, it internally lubricates the cement matrix to increase the efficiency of any cementitious system. This allows the production of concrete and mortars with higher strengths, better freeze/thaw resistance, and lower permeability.  It can also be used to increase the workability of concrete and mortar while maintaining water content.

Metco WR is a liquid admixture for concrete and mortar that allows water reduction without sacrificing slump or workability. Through a chemical process, it internally lubricates the cement matrix to increase the efficiency of any cementitious system. This allows the production of concrete and mortars with higher strengths, better freeze/thaw resistance, and lower permeability. It can also be used to increase the workability of concrete and mortar while maintaining water content.

Microforce is a microsilica based additive designed to enhance the hardened properties of concrete and mortar.  Through direct addition to cement based materials, concrete and mortar strengths and durability can be greatly enhanced.  Because Microforce chemically reacts with the cement matrix, it permanently densifies the concrete or mortar to produce excellent resistance to water and salt penetration. Compressive, flexural and bond strengths are significantly increased.

Surftard is a specially formulated liquid which reacts chemically with the cement matrix of concrete to temporarily retard the set. It allows production of horizontal  exposed aggregate surfaces and is excellent for both interior and exterior applications.

Waterhold is a water-based, VOC compliant spray-on liquid for application over fresh concrete surfaces.  By forming a continuous monomolecular film over the surface, it keeps bleed water in the concrete under hot, windy, or dry conditions.  By retarding the evaporation of bleed water, plastic shrinkage cracking and crusting is minimized or avoided. Waterhold enhances the finishing characteristics of concrete flatwork and is excellent as a finishing aid.

Formease is a ready-to-use organic concrete form release agent.  It is suitable for all types of formwork including wood, metal, plastic and fiberglass.  Formease leaves a smooth, unstained and void free concrete surface.

Formease VOC is a ready-to-use water-based concrete form release agent. It is suitable for all types of formwork including wood, metal, plastic and fiberglass. Formease VOC leaves a smooth, unstained and void free concrete surface.

Formease Supreme is a ready-to-use, specially formulated concrete form release agent for architectural concrete.  It is suitable for all types  of formwork including wood, metal, plastic and fiberglass. Formease Supreme leaves a smooth, unstained and void free concrete surface with high-slump, superplasticized concrete.

Mortarset Liquid is a liquid admixture formulated to accelerate the set of mortar in cold weather.  Mortarset Liquid is added to both  masonry and portland cement mortars used to lay brick, block, stone, tile and glass block. Mortarset Liquid also improves workability while increasing early age strengths of mortar.

Mortarset Powder is a powdered admixture formulated to accelerate the set of mortar in cold weather.  Mortarset Powder also improves workability while increasing early age strengths of mortar. Mortarset Powder is added to both masonry and portland cement used to lay brick, block, stone, tile and glass block.

Mortarset Plus is a non-chloride and non-corrosive based liquid admixture formulated to accelerate the set of mortar in cold weather. Mortarset Plus is added to both masonry and portland cement mortars used to lay brick, block, stone, tile and glass block. Mortarset Plus also improves workability while increasing early age strengths of mortar.

Metalcrete Waterproofing is a combination of metal particles, hardening agents, and oxidizing chemicals used to waterproof foundation walls and other  concrete and masonry substrates above or below ground, inside or outside.

Blokcoat is a cementitious coating system enhanced with unique polymers designed to decorate, waterproof and protect block, brick and concrete surfaces.  Blokcoat may be used in both above grade and below grade applications.  Blokcoat fills voids and smooths all surfaces to provide a decorative and textured finish.

Blokcoat FR is a cementitious coating system enhanced with polypropylene fibers and proprietary polymers designed to decorate, waterproof and protect block, brick and concrete surfaces.  Blokcoat FR may be used in both above grade and below grade applications.  Blokcoat FR fills voids and smooths all surfaces to provide a decorative and textured finish.

Brickseal is a single-component acrylic-based sealer formulated to protect and coat brick, stone, block, stucco, and mortar. Brickseal protects masonry from rain, sleet, snow, de-icing chemicals and acid rain.  Brickseal chemically adheres to most surfaces producing a weather and wear resistant sealer.

Penabrick SB is a single-component, solvent-based, silicone based sealer designed to penetrate and protect brick, stone, stucco and mortar. Penabrick SB is a very low viscosity water repellent capable of penetrating most substrates.  It protects surfaces from rain, sleet, snow, de-icing chemicals and acid rain.  Penabrick SB penetrates and adheres to most surfaces, producing a weather resistant sealer. Penabrick SB can be applied over previously waterproofed surfaces

Penabrick WB is a water-based, single-component, VOC compliant, silicone waterproofing sealer designed to penetrate and protect brick, stone, stucco and mortar.  Penabrick WB is a very low viscosity water repellent capable of penetrating most substrates.  It protects surfaces from rain, sleet, snow, de-icing chemicals and acid rain. Penabrick WB penet rates and adheres to most surfaces, producing a weather resistant sealer.  Penabrick WB should be used on surfaces that are porous and have not been previously waterproofed. Use Penabrick SB to retreat previously waterproofed surfaces.

Penabrick Plus is a single component siloxane based sealer designed to penetrate and protect brick, stone, stucco and mortar.  Penabrick Plus penetrates and  adheres to most surfaces producing a weather-resistant sealer. It chemically reacts within the pore structure to form a blocking compound that virtually waterproofs the surface.

Coldbraze is an epoxy-based repair compound specially formulated to reinforce and repair iron, steel and other metallic surfaces. Coldbraze economically extends the serviceable life of metal linings, blow pipes, dust collecting units, weld joints, anchor supports, iron castings and mechanical parts.

Bitesin is a concentrated acid formulation in liquid form used to prepare concrete and other substrates for resurfacing overlays, paint, coatings and other surface treatments.  Bitesin etches away the relatively high proportion of portland cement commonly found at the surface of concrete by removing laitance, grime, embedded dirt, and other deleterious matter providing a clean, porous surface.

Glaze-Off is a liquid surface treatment designed to remove the glaze from ceramic and quarry tile to promote adhesion of paints, coatings, and floor coverings.  It may also be used as a preparation and cleaner for masonry and concrete surfaces where coatings are to be applied.  Glaze-Off is ideal as a surface preparation  for  subsequent application of Porselin epoxy paint.

DL Solvent is used to clean or remove epoxy and urethane liquid compounds from mixing equipment and application tools. DL Solvent can also be used to remove spills and other unwanted deposits as well as common hydrocarbon-based curing compounds and sealer.

Metco Stripper is a thick, gel-like liquid that is used to remove paint, coatings, wax, asphalt, tar, curing compounds and sealers. It may be used on wood, concrete, plaster or metal surfaces which require removal of coatings. Metco Stripper may be used as a cleaner on terrazzo floors to remove built up grime and restore floors to original condition.

Roll N Go is a patching compound designed to be placed into chuck holes, ruts, breaks and other depressions in concrete or asphalt. Roll N Go is a proprietary formulated repair compound that is pre-mixed and ready for use directly from the container.

Formaseal is an extruded flexible sealant designed for a wide variety of sealing requirements. Formaseal is used  to seal  and silence the rattling of loose manhole  covers, catch basin grills, meter pit caps and sewer lids.  It is used on roofs to seal open seams, cracks, flashing around pipes, ventilators and gutters.

Waterzall Concentrate is a general purpose cleaning agent.  It is formulated to be used at full strength for spot cleaning, or diluted with water for cleaning large areas or for clean-up of tools and equipment.  Waterzall Concentrate dissolves and removes dirt, tacky film, spots, smudges and most unwanted deposits from floors, walls, doors, plastics, metal, rubber, fabric, carpeting and virtually any other surface. Use Waterzall Concentrate for clean-up of Diamite, Lexite, and Metco Epoxy Products.

Waterzall Degreaser is a liquid compound designed to change oil-based materials into a water-soluble state so that they may be rinsed away thoroughly and effectively with water.  Waterzall Degreaser completely removes oil, grease, grime and other gummy deposits from virtually all types of surfaces.

Zeromate is an effective snow and ice melting pelletized chemical compound. Zeromate melts ice at temperatures of -50°F (-46°C).  Zeromate may also be used to control dust, dehumidify damp rooms and freeze-proofing water type fire extinguishers.

Metco Anti-Skid Aggregate is intended for use as a skidproofing compound that may be incorporated into both liquid coating systems and fresh concrete.  It is  designed for light to heavy-duty applications where slip-resistance is critical.  Metco Anti-Skid Aggregate also provides floor surfaces with additional abrasion  resistance and withstands impact from heavy repetitive loads.